ZXR10-TWAMP-MIB

All MIBs › ZXR10-TWAMP-MIB

Organization: ZTE Corporation

Last Updated: 2017-11-14

Category: ZTE ZXR10 MPLS and Traffic Engineering

Description: Defines ZTE ZXR10 TWAMP test sessions for two-way active measurement of IP network delay and packet loss.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ZXR10-TWAMP-MIB?

ZXR10-TWAMP-MIB is a ZTE-specific MIB for their ZXR10 router/switch platform implementing TWAMP (Two-Way Active Measurement Protocol), used to actively measure round-trip IP network delay, jitter, and packet loss between two TWAMP-capable devices. It exposes configuration and results data for TWAMP test sessions rather than physical hardware counters. Its monitoring value is centered on network performance/software status: TWAMP session results reveal delay, loss, and jitter metrics that indicate WAN/network path health, which is essential for SLA verification and performance troubleshooting on ZTE-based networks. It builds on and complements the IETF TWAMP standard (RFC 5357) framework, adapting it for ZTE's proprietary SNMP tree. It's typically deployed on ZXR10 routers in service-provider networks needing active performance measurement for SLA monitoring, and administrators can download the ZXR10-TWAMP-MIB file to integrate it into their measurement toolchain.

IPNetwork Monitor allows you to monitor SNMP objects defined in ZXR10-TWAMP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ZTE ZXR10 router/switch

Monitoring Examples

Because sample_objects for this MIB were not available, specific table/object names cannot be cited, but a realistic scenario given the description would involve polling a TWAMP session/results table to retrieve round-trip delay, jitter, and packet loss statistics between the ZXR10 device and a remote TWAMP responder. An admin would watch for rising loss or delay values as an indicator of network path degradation. Without the object list, exact column names for session configuration or results cannot be confirmed.

Imported Objects

From SNMPv2-SMI

Counter32
Counter64
IpAddress
MODULE-IDENTITY
OBJECT-IDENTITY
OBJECT-TYPE
Unsigned32
enterprises

From SNMPv2-TC

DisplayString
RowStatus

How to Use in IPNetwork Monitor

Example using zxr10twampResultTwDelay OID:

Select a ZTE ZXR10 router/switch (TWAMP delay/jitter/loss test-result status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type zxr10twampResultTwDelay into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the two way delay.(unit: ns). On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
twampMib	1.3.6.1.4.1.3902.3.6000
zte	1.3.6.1.4.1.3902
zxr10	1.3.6.1.4.1.3902.3
zxr10twampClientListEntry	1.3.6.1.4.1.3902.3.6000.134.6.1		not-accessible	An entry containing configuration information applicable to a particular client list of TWAMP
IP zxr10twampClientListMember	1.3.6.1.4.1.3902.3.6000.134.6.1.1	IpAddress	not-accessible	IP address of the white list.
ROW zxr10twampClientListRowStatus	1.3.6.1.4.1.3902.3.6000.134.6.1.2	RowStatus	read-create	Row status
zxr10twampClientListTable	1.3.6.1.4.1.3902.3.6000.134.6		not-accessible	The configuration table of TWAMP client list.
zxr10twampConnectionEntry	1.3.6.1.4.1.3902.3.6000.134.1.1		not-accessible	An entry containing configuration informations which apply to the particular connection of TWAMP.
U32 zxr10twampConnectionId	1.3.6.1.4.1.3902.3.6000.134.1.1.1	Unsigned32	not-accessible	Connection ID used to identify the TWAMP connection.
U32 zxr10twampConnectionReCount	1.3.6.1.4.1.3902.3.6000.134.1.1.5	Unsigned32	read-create	The failed repetition number of TWAMP connection.(default :10)
U32 zxr10twampConnectionReInterval	1.3.6.1.4.1.3902.3.6000.134.1.1.6	Unsigned32	read-create	The failed repetition interval of TWAMP connection.(default :30s)
ROW zxr10twampConnectionRowStatus	1.3.6.1.4.1.3902.3.6000.134.1.1.7	RowStatus	read-create	Row status
IP zxr10twampConnectionSvrAddress	1.3.6.1.4.1.3902.3.6000.134.1.1.2	IpAddress	read-create	The server IP address which is specified by TWAMP connection.
U32 zxr10twampConnectionSvrPort	1.3.6.1.4.1.3902.3.6000.134.1.1.3	Unsigned32	read-create	The server TCP port which is specified by TWAMP connection.
zxr10twampConnectionTable	1.3.6.1.4.1.3902.3.6000.134.1		not-accessible	The configuration table of TWAMP connection.
STR zxr10twampConnectionVrfName	1.3.6.1.4.1.3902.3.6000.134.1.1.4	DisplayString	read-create	The VRF name of TWAMP connection.
zxr10twampMIB	1.3.6.1.4.1.3902.3.6000.134			ZXROS SMI MIB
INT zxr10twampOdOperation	1.3.6.1.4.1.3902.3.6000.134.4.1.2	INTEGER	read-write	The on-demand operation type which including start and stop. (default :stop)
zxr10twampOdOperationEntry	1.3.6.1.4.1.3902.3.6000.134.4.1		not-accessible	An entry containing configuration information applicable to a particular on-demand test of TWAMP.
U32 zxr10twampOdOperationId	1.3.6.1.4.1.3902.3.6000.134.4.1.1	Unsigned32	not-accessible	The connection ID applies to the on-demand test of TWAMP.
zxr10twampOdOperationTable	1.3.6.1.4.1.3902.3.6000.134.4		not-accessible	The configuration table of on-demand TWAMP test.
INT zxr10twampProOperation	1.3.6.1.4.1.3902.3.6000.134.3.1.2	INTEGER	read-write	The proactive operation type which including start and stop. (default :stop)
zxr10twampProOperationEntry	1.3.6.1.4.1.3902.3.6000.134.3.1		not-accessible	An entry containing configuration information applicable to a particular proactive test of TWAMP.
U32 zxr10twampProOperationId	1.3.6.1.4.1.3902.3.6000.134.3.1.1	Unsigned32	not-accessible	The connection ID applies to the proactive test of TWAMP.
zxr10twampProOperationTable	1.3.6.1.4.1.3902.3.6000.134.3		not-accessible	The configuration table of proactive TWAMP test.
U32 zxr10twampResultConnectionId	1.3.6.1.4.1.3902.3.6000.134.7.1.1	Unsigned32	not-accessible	The connection ID,ranges from 1 to 65535.
zxr10twampResultEntry	1.3.6.1.4.1.3902.3.6000.134.7.1		not-accessible	An entry containing result information applicable to TWAMP detecting.
C64 zxr10twampResultFwdDelay	1.3.6.1.4.1.3902.3.6000.134.7.1.15	Counter64	read-only	The forward packet delay.(unit: ns)
C64 zxr10twampResultFwdDelayAvg	1.3.6.1.4.1.3902.3.6000.134.7.1.18	Counter64	read-only	The average of forward packet delay.(unit: ns)
C64 zxr10twampResultFwdDelayMax	1.3.6.1.4.1.3902.3.6000.134.7.1.17	Counter64	read-only	The maximum of forward packet delay.(unit: ns)
C64 zxr10twampResultFwdDelayMin	1.3.6.1.4.1.3902.3.6000.134.7.1.16	Counter64	read-only	The minimum of forward packet delay.(unit: ns)
C64 zxr10twampResultFwdJitter	1.3.6.1.4.1.3902.3.6000.134.7.1.19	Counter64	read-only	Delay jitter of the forward packet.(unit: ns)
C64 zxr10twampResultFwdJitterAvg	1.3.6.1.4.1.3902.3.6000.134.7.1.22	Counter64	read-only	The average of delay jitter of the forward packet.(unit: ns)
C64 zxr10twampResultFwdJitterMax	1.3.6.1.4.1.3902.3.6000.134.7.1.21	Counter64	read-only	The maximum of delay jitter of the forward packet.(unit: ns)
C64 zxr10twampResultFwdJitterMin	1.3.6.1.4.1.3902.3.6000.134.7.1.20	Counter64	read-only	The minimum of delay jitter of the forward packet.(unit: ns)
U32 zxr10twampResultPktLossNum	1.3.6.1.4.1.3902.3.6000.134.7.1.5	Unsigned32	read-only	The count of lossing packets.
U32 zxr10twampResultPktLossRatio	1.3.6.1.4.1.3902.3.6000.134.7.1.6	Unsigned32	read-only	The packet loss ratio which the precision is 1/1000000.
U32 zxr10twampResultPktRcvNum	1.3.6.1.4.1.3902.3.6000.134.7.1.4	Unsigned32	read-only	The count of receiving packets.
U32 zxr10twampResultPktSendNum	1.3.6.1.4.1.3902.3.6000.134.7.1.3	Unsigned32	read-only	The count of sending packets.
C64 zxr10twampResultRvsDelay	1.3.6.1.4.1.3902.3.6000.134.7.1.23	Counter64	read-only	The reverse packet delay.(unit: ns)
C64 zxr10twampResultRvsDelayAvg	1.3.6.1.4.1.3902.3.6000.134.7.1.26	Counter64	read-only	The average of reverse packet delay.(unit: ns)
C64 zxr10twampResultRvsDelayMax	1.3.6.1.4.1.3902.3.6000.134.7.1.25	Counter64	read-only	The maximum of reverse packet delay.(unit: ns)
C64 zxr10twampResultRvsDelayMin	1.3.6.1.4.1.3902.3.6000.134.7.1.24	Counter64	read-only	The minimum of reverse packet delay.(unit: ns)
C64 zxr10twampResultRvsJitter	1.3.6.1.4.1.3902.3.6000.134.7.1.27	Counter64	read-only	The reverse packet delay jitter.(unit: ns)
C64 zxr10twampResultRvsJitterAvg	1.3.6.1.4.1.3902.3.6000.134.7.1.30	Counter64	read-only	The average of delay jitter of the reverse packet.(unit: ns)
C64 zxr10twampResultRvsJitterMax	1.3.6.1.4.1.3902.3.6000.134.7.1.29	Counter64	read-only	The maximum of delay jitter of the reverse packet.(unit: ns)
C64 zxr10twampResultRvsJitterMin	1.3.6.1.4.1.3902.3.6000.134.7.1.28	Counter64	read-only	The minimum of delay jitter of the reverse packet.(unit: ns)
U32 zxr10twampResultSessionId	1.3.6.1.4.1.3902.3.6000.134.7.1.2	Unsigned32	not-accessible	The session ID,ranges from 1 to 65535.
zxr10twampResultTable	1.3.6.1.4.1.3902.3.6000.134.7		not-accessible	The result table of TWAMP detecting.
C64 zxr10twampResultTwDelayEx	1.3.6.1.4.1.3902.3.6000.134.7.1.7	Counter64	read-only	Two way delay.(unit: ns)
C64 zxr10twampResultTwDelayAvg	1.3.6.1.4.1.3902.3.6000.134.7.1.10	Counter64	read-only	The average of two way delay.(unit: ns)
C64 zxr10twampResultTwDelayMax	1.3.6.1.4.1.3902.3.6000.134.7.1.9	Counter64	read-only	The maximum of two way delay.(unit: ns)
C64 zxr10twampResultTwDelayMin	1.3.6.1.4.1.3902.3.6000.134.7.1.8	Counter64	read-only	The minimum of two way delay.(unit: ns)
C64 zxr10twampResultTwJitter	1.3.6.1.4.1.3902.3.6000.134.7.1.11	Counter64	read-only	Delay jitter of two way packet.(unit: ns)
C64 zxr10twampResultTwJitterAvg	1.3.6.1.4.1.3902.3.6000.134.7.1.14	Counter64	read-only	The average delay jitter of two way packet.(unit: ns)
C64 zxr10twampResultTwJitterMax	1.3.6.1.4.1.3902.3.6000.134.7.1.13	Counter64	read-only	The maximum delay jitter of two way packet.(unit: ns)
C64 zxr10twampResultTwJitterMin	1.3.6.1.4.1.3902.3.6000.134.7.1.12	Counter64	read-only	The minimum delay jitter of two way packet.(unit: ns)
zxr10twampServer	1.3.6.1.4.1.3902.3.6000.134.5
U32 zxr10twampSessionConnectionId	1.3.6.1.4.1.3902.3.6000.134.2.1.1	Unsigned32	not-accessible	The connection ID applies to the session of TWAMP.
INT zxr10twampSessionDetectPath	1.3.6.1.4.1.3902.3.6000.134.2.1.8	INTEGER	read-create	The detect path type of TWAMP session.(default :down)
U32 zxr10twampSessionDscp	1.3.6.1.4.1.3902.3.6000.134.2.1.10	Unsigned32	read-create	The DSCP value of TWAMP session.(default :0)
INT zxr10twampSessionDurationMode	1.3.6.1.4.1.3902.3.6000.134.2.1.13	INTEGER	read-create	The sending packet mode: continuous:In this mode,the test packets will always be sent until the user stops. packets:In this mode,the test will be stopped until the number of sending packet reaches the configured value. seconds:In this mode,the test will be stopped until the time of sending packet reaches the configured value.(default :continuous)
zxr10twampSessionEntry	1.3.6.1.4.1.3902.3.6000.134.2.1		not-accessible	An entry containing configuration informations which apply to the particular session of TWAMP.
U32 zxr10twampSessionId	1.3.6.1.4.1.3902.3.6000.134.2.1.2	Unsigned32	not-accessible	The identity of the TWAMP session.
STR zxr10twampSessionInboundIf	1.3.6.1.4.1.3902.3.6000.134.2.1.9	DisplayString	read-create	The inbound-interface of TWAMP session, and it applies to condition when the detect path type is up.
U32 zxr10twampSessionInterval	1.3.6.1.4.1.3902.3.6000.134.2.1.17	Unsigned32	read-create	Packet sending interval: If the unit is assigned second,it ranges from 1 to 60. If the unit is assigned millisecond,it ranges from 1 to 1000. If the unit is assigned microseconds,it ranges from 50 to 1000.
INT zxr10twampSessionIntervalUnit	1.3.6.1.4.1.3902.3.6000.134.2.1.16	INTEGER	read-create	The unit of sending interval which including second, millisecond and microsecond.(default :second)
U32 zxr10twampSessionPaddinglength	1.3.6.1.4.1.3902.3.6000.134.2.1.11	Unsigned32	read-create	The length of packet padding, and the upper limit of this parameter depends on the device.(default :27bytes)
IP zxr10twampSessionRcvAddress	1.3.6.1.4.1.3902.3.6000.134.2.1.5	IpAddress	read-create	The receiver IP address of TWAMP session.
U32 zxr10twampSessionRcvPort	1.3.6.1.4.1.3902.3.6000.134.2.1.6	Unsigned32	read-create	The receiver UDP port of TWAMP session.
ROW zxr10twampSessionRowStatus	1.3.6.1.4.1.3902.3.6000.134.2.1.19	RowStatus	read-create	Row status
IP zxr10twampSessionSenderAddress	1.3.6.1.4.1.3902.3.6000.134.2.1.3	IpAddress	read-create	The sender IP address of TWAMP session.
U32 zxr10twampSessionSenderPort	1.3.6.1.4.1.3902.3.6000.134.2.1.4	Unsigned32	read-create	The sender UDP port of TWAMP session.
U32 zxr10twampSessionSendPktCount	1.3.6.1.4.1.3902.3.6000.134.2.1.14	Unsigned32	read-create	The number of sending packet which applies to condition when the sending packet mode is packets.The test will be stopped until the number of sending packet reaches the configured value.
U32 zxr10twampSessionSendTime	1.3.6.1.4.1.3902.3.6000.134.2.1.15	Unsigned32	read-create	Sending time of packets which applies to condition when the sending packet mode is seconds. The test will be stopped until the time of sending packets reaches the configured value.
U32 zxr10twampSessionStatInterval	1.3.6.1.4.1.3902.3.6000.134.2.1.18	Unsigned32	read-create	The statistics interval,ranges from 5s to 60s.(default :15s)
zxr10twampSessionTable	1.3.6.1.4.1.3902.3.6000.134.2		not-accessible	The configuration table of TWAMP session.
U32 zxr10twampSessionTimeOut	1.3.6.1.4.1.3902.3.6000.134.2.1.12	Unsigned32	read-create	Timeout ranges from 1s to 10s. Within this time, the server needs to reflect the test message, otherwise the message is discarded.(default :5s)
STR zxr10twampSessionVrfName	1.3.6.1.4.1.3902.3.6000.134.2.1.7	DisplayString	read-create	The VRF name of TWAMP session.
INT zxr10twampSvrClientListStatus	1.3.6.1.4.1.3902.3.6000.134.5.9	INTEGER	read-write	The status of client list, including enable and disable. (default: disable)
INT zxr10twampSvrIgnoreVrf	1.3.6.1.4.1.3902.3.6000.134.5.8	INTEGER	read-write	The ignore-vrf status,including enable and disable. (default value depends on the device)
U32 zxr10twampSvrInactiveTimeOut	1.3.6.1.4.1.3902.3.6000.134.5.2	Unsigned32	read-write	Inactivity timeout,ranges from 10s to 1800s.(default: 900)
U32 zxr10twampSvrMaxConDuration	1.3.6.1.4.1.3902.3.6000.134.5.3	Unsigned32	read-write	The maximum duration of connection,ranges from 0h to 24h. If this node is assigned 0,it means permanence connection unless stopped manually.If it is assigned 1h to 24h,it means connection lasting time.(default: 0)
U32 zxr10twampSvrMaxConnection	1.3.6.1.4.1.3902.3.6000.134.5.4	Unsigned32	read-write	The maximum number of connections which the minimum value is 1, and the maximum value of this parameter depends on the device. (default: 64)
U32 zxr10twampSvrMaxSePerConn	1.3.6.1.4.1.3902.3.6000.134.5.6	Unsigned32	read-write	The maximum session number of each connection which the minimum value is 1, and the maximum value of this parameter depends on the device.(default: 8)
U32 zxr10twampSvrMaxSession	1.3.6.1.4.1.3902.3.6000.134.5.5	Unsigned32	read-write	The maximum number of sessions which the minimum value is 1, and the maximum value of this parameter depends on the device. (default: 128)
U32 zxr10twampSvrPort	1.3.6.1.4.1.3902.3.6000.134.5.7	Unsigned32	read-write	The port number of server, ranges from 1025 to 65535, or 862. (default: 862)
INT zxr10twampSvrStatus	1.3.6.1.4.1.3902.3.6000.134.5.1	INTEGER	read-write	The status of TWAMP server,including enable and disable. (default: disable)

RFC description

Manages TWAMP (Two-Way Active Measurement Protocol) connections and configuration for ZXR10 routers.

Start monitoring ZTE ZXR10 router/switch (TWAMP delay/jitter/loss test-result status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ZXR10-TWAMP-MIB

What Is ZXR10-TWAMP-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

How to Use in IPNetwork Monitor

RFC description