ZXR10-MPLS-TRAFFIC-STAT-MIB

All MIBs › ZXR10-MPLS-TRAFFIC-STAT-MIB

Category: ZTE ZXR10 MPLS and Traffic Engineering

Description: Provides ZTE ZXR10 MPLS traffic statistics including per-LSP packet and byte counters for performance analysis.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ZXR10-MPLS-TRAFFIC-STAT-MIB?

ZXR10-MPLS-TRAFFIC-STAT-MIB is a ZTE enterprise MIB module for the ZXR10 series routers/switches that exposes MPLS traffic statistics, specifically per-LSP (Label Switched Path) packet and byte counters used for performance analysis. As a monitoring resource its primary category of data is performance counters - traffic volume flowing over individual LSPs - rather than configuration or hardware sensors. Because it focuses on LSP-level packet/byte counts, it is used by operators to track MPLS network utilization and detect anomalies such as an LSP carrying unexpectedly low or zero traffic (a possible path failure) or unexpectedly high traffic (potential congestion). It necessarily depends on the base MPLS LSP/label-switching MIBs (e.g., MPLS-LSR-MIB or ZTE's own MPLS MIBs) to identify which LSP each statistics entry corresponds to. It is deployed on ZTE ZXR10 routers in MPLS-enabled service-provider or enterprise backbone networks to analyze traffic engineering and capacity planning, with operators typically loading it into a ZXR10-MPLS-TRAFFIC-STAT-MIB MIB Browser session to inspect the per-LSP counters directly.

IPNetwork Monitor allows you to monitor SNMP objects defined in ZXR10-MPLS-TRAFFIC-STAT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ZTE ZXR10 series router/switch

Monitoring Examples

No real object or table names were captured for this MIB (sample_objects contains only the "IMPORTS" clause, not an actual data object), so a specific polling example cannot be grounded in verified object names. Based on the module's stated purpose, an operator would generally be expected to poll per-LSP packet and byte counters to track MPLS traffic volume and detect under- or over-utilized label-switched paths, but this remains a general characterization rather than a confirmed example.

What Can Be Monitored

per-LSP packet counters
per-LSP byte counters

Imported Objects

From SNMPv2-SMI

Counter64
IpAddress
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus

From ZXR10-SMI

zxr10

OBJECT-IDENTITY

How to Use in IPNetwork Monitor

Example using zxr10MplsTeOutTotalSend OID:

Select a ZTE ZXR10 series router/switch (per-LSP packet/byte traffic-counter status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type zxr10MplsTeOutTotalSend into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the total number of sent packets of out-traffic. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
mpls_traffic_stat	1.3.6.1.4.1.3902.3.325
mpls_te_stat	1.3.6.1.4.1.3902.3.325.2
zxr10MplsTeStatisticsOutTable	1.3.6.1.4.1.3902.3.325.2.1		not-accessible	A table that contains MPLS TE out-traffic statistics.
zxr10MplsTeStatisticsOutEntry	1.3.6.1.4.1.3902.3.325.2.1.1		not-accessible	A list of entries of MPLS TE out-traffic statistics.
U32 zxr10MplsTeOutTunnelId	1.3.6.1.4.1.3902.3.325.2.1.1.1	Unsigned32	read-only	The MPLS TE tunnel which the out label belongs to.
C64 zxr10MplsTeOutTotalSendEx	1.3.6.1.4.1.3902.3.325.2.1.1.2	Counter64	read-only	Total number of sent packets of out-traffic.
C64 zxr10MplsTeOutTotalDrop	1.3.6.1.4.1.3902.3.325.2.1.1.3	Counter64	read-only	Total number of dropped packets of out-traffic.
C64 zxr10MplsTeOutTotalByte	1.3.6.1.4.1.3902.3.325.2.1.1.4	Counter64	read-only	Total number of sent bytes of out-traffic.
C64 zxr10MplsTeOutTotalDropByte	1.3.6.1.4.1.3902.3.325.2.1.1.5	Counter64	read-only	Total number of dropped bytes of out-traffic.
U32 zxr10MplsTeOutSendByteRate	1.3.6.1.4.1.3902.3.325.2.1.1.6	Unsigned32	read-only	The bandwith of sent out-traffic,its unit is Bps.

RFC description

MPLS traffic engineering tunnel statistics for ZXR10 carrier-class routers.

Start monitoring ZTE ZXR10 series router/switch (per-LSP packet/byte traffic-counter status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ZXR10-MPLS-TRAFFIC-STAT-MIB