ZXR10-PROTOCOL-MIB

All MIBs › ZXR10-PROTOCOL-MIB

Category: ZTE ZXR10 IP Routing

Description: Defines ZTE ZXR10 protocol configuration objects for enabling and managing routing and switching protocols.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ZXR10-PROTOCOL-MIB?

This is a ZTE-specific MIB for the ZXR10 router/switch family, providing a general set of objects for enabling and configuring various routing and switching protocols supported by the device (e.g., toggling protocol support on or off at a system or interface level). It exposes primarily configuration/administrative-state data rather than protocol-specific performance metrics, acting as a higher-level control point that determines which protocol feature sets are active. Its monitoring value is configuration and feature-enablement verification: administrators can confirm which protocols are currently enabled on the device before troubleshooting protocol-specific issues, since a disabled protocol object would explain why an expected protocol MIB shows no active state elsewhere. It functions as a companion/summary layer to the many protocol-specific ZXR10 MIBs (BGP, OSPF, ACL, etc.), since those modules assume the relevant protocol has already been enabled here. It is typically deployed by network engineers performing initial configuration or troubleshooting protocol availability on ZXR10 routers and switches. Engineers can download the ZXR10-PROTOCOL-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ZXR10-PROTOCOL-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ZTE ZXR10 router/switch

Monitoring Examples

An engineer checks protocol enablement objects on a ZXR10 device to confirm that a routing protocol like BGP or OSPF is administratively enabled before investigating why no routes are being learned via that protocol's dedicated MIB. If a protocol appears disabled here despite being expected to run, that configuration mismatch is the likely root cause rather than a fault in the protocol's own state tables. No sample objects were present in the source extract, so exact object names cannot be confirmed here.

What Can Be Monitored

protocol enable/disable state
supported protocol feature set
system-level protocol configuration

Imported Objects

From RFC1155-SMI

IpAddress

From SNMPv2-SMI

Integer32
OBJECT-TYPE
enterprises

OIDs

OID symbolic	OID numeric	Type	Access	Description
zte	1.3.6.1.4.1.3902
zxr10	1.3.6.1.4.1.3902.3
zxr10protocol	1.3.6.1.4.1.3902.3.101
zxr10ip	1.3.6.1.4.1.3902.3.101.1
zxr10ipvrfaddrTable	1.3.6.1.4.1.3902.3.101.1.1		not-accessible	The description of zxr10 vrf address table. It is a list of vrf address entries.
zxr10ipvrfaddrEntry	1.3.6.1.4.1.3902.3.101.1.1.1		not-accessible	A vrf address entry containing objects that vrf interface address infomation,such as: vrf ifindex, vrf address, mask.
STR zxr10ipVrfVpnName	1.3.6.1.4.1.3902.3.101.1.1.1.1	DisplayString	read-only	The IP address of this vrf interface.
IP zxr10ipVrfAddr	1.3.6.1.4.1.3902.3.101.1.1.1.2	IpAddress	read-only	The IP address of this vrf interface.
IP zxr10ipVrfNetMask	1.3.6.1.4.1.3902.3.101.1.1.1.3	IpAddress	read-only	The subnet mask associated with the IP address of this vrf interface. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
I32 zxr10ipVrfIfIndex	1.3.6.1.4.1.3902.3.101.1.1.1.4	Integer32	read-only	The index value which uniquely identifies the vrf interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
I32 zxr10ipVrfBcastAddr	1.3.6.1.4.1.3902.3.101.1.1.1.5	Integer32	read-only	The value of the least-significant bit in the IP broadcast address used for sending datagrams on the vrf interface associated with the IP address. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the vrf interface.
I32 zxr10ipVrfReasmMaxSize	1.3.6.1.4.1.3902.3.101.1.1.1.6	Integer32	read-only	The size of the largest IP datagram which this vrf interface can re-assemble from incoming IP fragmented datagrams received on this interface.
zxr10tcp	1.3.6.1.4.1.3902.3.101.2
zxr10tcpConnTable	1.3.6.1.4.1.3902.3.101.2.1		not-accessible	A table containing TCP connection-specific information.
zxr10tcpconnEntry	1.3.6.1.4.1.3902.3.101.2.1.1		not-accessible	Information about a particular current TCP connection. An object of this type is transient, in that it ceases to exist when (or soon after) the connection makes the transition to the CLOSED state.
STR zxr10tcpConnVrfVpnName	1.3.6.1.4.1.3902.3.101.2.1.1.1	DisplayString	read-only	The IP address of this vrf interface.
INT zxr10tcpConnState	1.3.6.1.4.1.3902.3.101.2.1.1.2	INTEGER	read-write	The state of this TCP connection. The only value which may be set by a management station is deleteTCB(12). Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to set this object to any other value. If a management station sets this object to the value deleteTCB(12), then this has the effect of deleting the TCB (as defined in RFC 793) of the corresponding connection on the managed node, resulting in immediate termination of the connection. As an implementation-specific option, a RST segment may be sent from the managed node to the other TCP endpoint (note however that RST segments are not sent reliably).
IP zxr10tcpConnLocalAddress	1.3.6.1.4.1.3902.3.101.2.1.1.3	IpAddress	read-only	The local IP address for this TCP connection. In the case of a connection in the listen state which is willing to accept connections for any IP interface associated with the node, the value 0.0.0.0 is used.
INT zxr10tcpConnLocalPort	1.3.6.1.4.1.3902.3.101.2.1.1.4	INTEGER	read-only	The local port number for this TCP connection.
IP zxr10tcpConnRemAddress	1.3.6.1.4.1.3902.3.101.2.1.1.5	IpAddress	read-only	The remote IP address for this TCP connection.
INT zxr10tcpConnRemPort	1.3.6.1.4.1.3902.3.101.2.1.1.6	INTEGER	read-only	The remote port number for this TCP connection.

RFC description

ZTE ZXR10 router vendor MIB defining protocol-related objects including VRF IP addressing and TCP statistics.

Start monitoring ZTE ZXR10 router/switch (per-protocol feature-enablement config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ZXR10-PROTOCOL-MIB

What Is ZXR10-PROTOCOL-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description