All MIBs › ZXR10-P2MP-TE-MIB
Organization: ZTE Corporation
Last Updated: 2016-01-29
Category: ZTE ZXR10 Multicast
Description: Defines ZTE ZXR10 Point-to-Multipoint MPLS TE tunnel configuration for multicast traffic engineering.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ZXR10-P2MP-TE-MIB?
ZXR10-P2MP-TE-MIB is a ZTE private module for ZXR10 routers covering Point-to-Multipoint MPLS Traffic Engineering tunnels, used to engineer multicast-style distribution trees across an MPLS network. It exposes configuration objects for local P2MP tunnel definitions, including destination leaf identification, bandwidth reservation, setup priority, and route-recording/integrity options. Its monitoring value is in verifying the software configuration and provisioning correctness of P2MP TE tunnels, letting an operator confirm a tunnel's destination leaves, reserved bandwidth, and priority settings are as intended, which helps catch a misconfigured or under-provisioned multicast TE tree before it causes packet loss under load. It depends on general MPLS-TE conventions (bandwidth, setup priority, route-recording) shared with unicast MPLS-TE MIBs. It is deployed on ZTE ZXR10 core routers delivering multicast or point-to-multipoint services (e.g., IPTV distribution) over an MPLS-TE backbone. Network engineers evaluating or troubleshooting this functionality can download the ZXR10-P2MP-TE-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in ZXR10-P2MP-TE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- ZTE ZXR10 MPLS core router
Monitoring Examples
An administrator would inspect zxr10P2mpTeLocTnnlCfgTable entries, keyed by zxr10P2mpTeLocTnnlCfgName and zxr10P2mpTeLocTnnlCfgIndex, checking zxr10P2mpTeLocTnnlCfgDestLType and zxr10P2mpTeLocTnnlCfgDestLName/zxr10P2mpTeLocTnnlCfgDestLID to confirm all expected destination leaves are present in the P2MP tree. Reviewing zxr10P2mpTeLocTnnlCfgBandwith and zxr10P2mpTeLocTnnlCfgSetupprio verifies the tunnel's reserved bandwidth and priority match the service requirement, while zxr10P2mpTeLocTnnlCfgRRO shows whether route recording is enabled for path visibility. A destination leaf missing from the table would reveal that a receiver site has dropped out of the multicast distribution tree.
What Can Be Monitored
- P2MP tunnel destination leaves
- reserved bandwidth per tunnel
- tunnel setup priority
- route-record option status
- tunnel integrity configuration
This MIB depends on
Related MIBs
Imported Objects
From SNMPv2-SMI
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| MacAddress | |
| RowStatus | |
| TimeTicks | |
| TruthValue |
From ZXR10-SMI
| zxr10RosngMIB | OBJECT-IDENTITY |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| zxr10P2mpTeMIB | 1.3.6.1.4.1.3902.3.6000.205 | P2MP TE | ||
| zxr10P2mpTeGlobalObjects | 1.3.6.1.4.1.3902.3.6000.205.1 | |||
| zxr10P2mpTeObjects | 1.3.6.1.4.1.3902.3.6000.205.2 | |||
| zxr10P2mpTeLocTnnlCfgTable | 1.3.6.1.4.1.3902.3.6000.205.2.1 | not-accessible | ||
| zxr10P2mpTeLocTnnlCfgEntry | 1.3.6.1.4.1.3902.3.6000.205.2.1.1 | not-accessible | ||
| STR zxr10P2mpTeLocTnnlCfgName | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.1 | DisplayString | not-accessible | P2mp Local tunnel Name . |
| U32 zxr10P2mpTeLocTnnlCfgIndex | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.2 | Unsigned32 | read-only | P2mp Local tunnel Index. |
| INT zxr10P2mpTeLocTnnlCfgDestLType | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.3 | INTEGER | read-create | The destlist type of P2mp Local tunnel . |
| STR zxr10P2mpTeLocTnnlCfgDestLName | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.4 | DisplayString | read-create | The destlist type of P2mp Local tunnel is Name. |
| I32 zxr10P2mpTeLocTnnlCfgDestLID | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.5 | Integer32 | read-create | The destlist type of P2mp Local tunnel is Id. |
| T/F zxr10P2mpTeLocTnnlCfgIntegrity | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.6 | TruthValue | read-create | P2mp Local tunnel is configed Integrity . |
| T/F zxr10P2mpTeLocTnnlCfgRRO | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.7 | TruthValue | read-create | P2mp Local tunnel is configed Integrity RRO. |
| U32 zxr10P2mpTeLocTnnlCfgBandwith | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.8 | Unsigned32 | read-create | The total bandwith of P2mp Local tunnel . |
| I32 zxr10P2mpTeLocTnnlCfgSetupprio | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.9 | Integer32 | read-create | The Setupprio of P2mp Local tunnel . |
| I32 zxr10P2mpTeLocTnnlCfgHoldprio | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.10 | Integer32 | read-create | The Holdprio of P2mp Local tunnel . |
| INT zxr10P2mpTeLocTnnlCfgResvStyle | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.11 | INTEGER | read-create | The ResvStyle of P2mp Local tunnel . |
| T/F zxr10P2mpTeLocTnnlCfgReopEnable | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.12 | TruthValue | read-create | The ReopEnable of P2mp Local tunnel . |
| INT zxr10P2mpTeLocTnnlCfgCrkBackMode | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.13 | INTEGER | read-create | The CrankbackMode of P2mp Local tunnel . |
| T/F zxr10P2mpTeLocTnnlCfgFrrEnable | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.14 | TruthValue | read-create | The Frr of P2mp Local tunnel . |
| T/F zxr10P2mpTeLocTnnlCfgEscapepath | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.15 | TruthValue | read-create | The Escapepath of P2mp Local tunnel . |
| T/F zxr10P2mpTeLocTnnlCfgBfd | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.16 | TruthValue | read-create | The bfd enable of P2mp Local tunnel . |
| U32 zxr10P2mpTeLocTnnlCfgMinTxInter | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.17 | Unsigned32 | read-create | The bfd MinTxInterval of P2mp Local tunnel . |
| U32 zxr10P2mpTeLocTnnlCfgMinRxInter | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.18 | Unsigned32 | read-create | The bfd MinRxInterval of P2mp Local tunnel . |
| I32 zxr10P2mpTeLocTnnlCfgMult | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.19 | Integer32 | read-create | The bfd multiplier of P2mp Local tunnel . |
| T/F zxr10P2mpTeLocTnnlCfgE2E | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.20 | TruthValue | read-create | The e2e enable of P2mp Local tunnel . |
| ROW zxr10P2mpTeLocTnnlCfgRowStatus | 1.3.6.1.4.1.3902.3.6000.205.2.1.1.100 | RowStatus | read-create | Row status |
| zxr10P2mpTeLeafTnnlCfgTable | 1.3.6.1.4.1.3902.3.6000.205.2.2 | not-accessible | ||
| zxr10P2mpTeLeafTnnlCfgEntry | 1.3.6.1.4.1.3902.3.6000.205.2.2.1 | not-accessible | ||
| STR zxr10P2mpTeLeafTnnlCfgName | 1.3.6.1.4.1.3902.3.6000.205.2.2.1.1 | DisplayString | not-accessible | P2mp Leaf Tunnel Name. |
| U32 zxr10P2mpTeLeafTnnlCfgIndex | 1.3.6.1.4.1.3902.3.6000.205.2.2.1.2 | Unsigned32 | read-only | P2mp Leaf Tunnel index. |
| IP zxr10P2mpTeLeafTnnlCfgRootAddr | 1.3.6.1.4.1.3902.3.6000.205.2.2.1.3 | IpAddress | read-create | The IngressId of P2mp Leaf Tunnel. |
| I32 zxr10P2mpTeLeafTnnlCfgRootTnnlID | 1.3.6.1.4.1.3902.3.6000.205.2.2.1.4 | Integer32 | read-create | The Index of P2mp Leaf Tunnel. |
| U32 zxr10P2mpTeLeafTnnlCfgRootP2mpID | 1.3.6.1.4.1.3902.3.6000.205.2.2.1.5 | Unsigned32 | read-create | The P2mpId of P2mp Leaf Tunnel. |
| ROW zxr10P2mpTeLeafTnnlCfgRowStatus | 1.3.6.1.4.1.3902.3.6000.205.2.2.1.100 | RowStatus | read-create | RowStatus. |
| zxr10P2mpTeDsteCfgTable | 1.3.6.1.4.1.3902.3.6000.205.2.3 | not-accessible | ||
| zxr10P2mpTeDsteCfgEntry | 1.3.6.1.4.1.3902.3.6000.205.2.3.1 | not-accessible | ||
| STR zxr10P2mpTeDsteCfgTunnelName | 1.3.6.1.4.1.3902.3.6000.205.2.3.1.1 | DisplayString | not-accessible | The canonical name assigned to the tunnel. This name can be used to refer to the tunnel on the LSR's console port.If mplsTETunnelIsIf is set to true then the ifName of the interface corresponding to this tunnel should have a value equal to mplsTETunnelName. Also see the description of ifName in RFC 2863. |
| U32 zxr10P2mpTeDsteCfgClassType | 1.3.6.1.4.1.3902.3.6000.205.2.3.1.2 | Unsigned32 | not-accessible | The dste class type of this tunnel. |
| U32 zxr10P2mpTeDsteCfgBandwidth | 1.3.6.1.4.1.3902.3.6000.205.2.3.1.3 | Unsigned32 | read-create | The dste bandwidth of this tunnel. |
| ROW zxr10P2mpTeDsteCfgRowStatus | 1.3.6.1.4.1.3902.3.6000.205.2.3.1.100 | RowStatus | read-create | Row status. |
| zxr10P2mpTeDestLNameCfgTable | 1.3.6.1.4.1.3902.3.6000.205.2.4 | not-accessible | ||
| zxr10P2mpTeDestLNameCfgEntry | 1.3.6.1.4.1.3902.3.6000.205.2.4.1 | not-accessible | ||
| STR zxr10P2mpTeDestLNameCfgName | 1.3.6.1.4.1.3902.3.6000.205.2.4.1.1 | DisplayString | not-accessible | The Name of destlist. |
| ROW zxr10P2mpTeDestLNameCfgRowStatus | 1.3.6.1.4.1.3902.3.6000.205.2.4.1.100 | RowStatus | read-create | row status. |
| zxr10P2mpTeDestLIDCfgTable | 1.3.6.1.4.1.3902.3.6000.205.2.5 | not-accessible | ||
| zxr10P2mpTeDestLIDCfgEntry | 1.3.6.1.4.1.3902.3.6000.205.2.5.1 | not-accessible | ||
| U32 zxr10P2mpTeDestLIDCfgDestLID | 1.3.6.1.4.1.3902.3.6000.205.2.5.1.1 | Unsigned32 | not-accessible | The id of destlist. |
| ROW zxr10P2mpTeDestLIDCfgRowStatus | 1.3.6.1.4.1.3902.3.6000.205.2.5.1.100 | RowStatus | read-create | row status. |
| zxr10P2mpTeDstNameCfgTable | 1.3.6.1.4.1.3902.3.6000.205.2.6 | not-accessible | ||
| zxr10P2mpTeDstNameCfgEntry | 1.3.6.1.4.1.3902.3.6000.205.2.6.1 | not-accessible | ||
| STR zxr10P2mpTeDstNameCfgName | 1.3.6.1.4.1.3902.3.6000.205.2.6.1.1 | DisplayString | not-accessible | The Name of destlist. |
| IP zxr10P2mpTeDstNameCfgDestAddr | 1.3.6.1.4.1.3902.3.6000.205.2.6.1.2 | IpAddress | not-accessible | The destination address of destlistname. |
| I32 zxr10P2mpTeDstNameCfgPathOptNum | 1.3.6.1.4.1.3902.3.6000.205.2.6.1.3 | Integer32 | read-create | The destination address of destlistname. |
| INT zxr10P2mpTeDstNameCfgPathType | 1.3.6.1.4.1.3902.3.6000.205.2.6.1.4 | INTEGER | read-create | The pathtype of destname. |
| STR zxr10P2mpTeDstNameCfgExpPathName | 1.3.6.1.4.1.3902.3.6000.205.2.6.1.5 | DisplayString | read-create | The explicit pathname of destname. |
| I32 zxr10P2mpTeDstNameCfgExpPathID | 1.3.6.1.4.1.3902.3.6000.205.2.6.1.6 | Integer32 | read-create | The explicit pathid of destname. |
| ROW zxr10P2mpTeDstNameCfgRowStatus | 1.3.6.1.4.1.3902.3.6000.205.2.6.1.100 | RowStatus | read-create | Row status. |
| zxr10P2mpTeDstIDCfgTable | 1.3.6.1.4.1.3902.3.6000.205.2.7 | not-accessible | ||
| zxr10P2mpTeDstIDCfgEntry | 1.3.6.1.4.1.3902.3.6000.205.2.7.1 | not-accessible | ||
| U32 zxr10P2mpTeDstIDCfgDestLID | 1.3.6.1.4.1.3902.3.6000.205.2.7.1.1 | Unsigned32 | not-accessible | The id of destlist. |
| IP zxr10P2mpTeDstIDCfgDestAddr | 1.3.6.1.4.1.3902.3.6000.205.2.7.1.2 | IpAddress | not-accessible | The destination address of destid. |
| I32 zxr10P2mpTeDstIDCfgPathOptNum | 1.3.6.1.4.1.3902.3.6000.205.2.7.1.3 | Integer32 | read-create | The pathopt num of destid. |
| INT zxr10P2mpTeDstIDCfgPathType | 1.3.6.1.4.1.3902.3.6000.205.2.7.1.4 | INTEGER | read-create | The pathtype of destid. |
| STR zxr10P2mpTeDstIDCfgExpPathName | 1.3.6.1.4.1.3902.3.6000.205.2.7.1.5 | DisplayString | read-create | The explicitpathname of destlistid. |
| I32 zxr10P2mpTeDstIDCfgExpPathID | 1.3.6.1.4.1.3902.3.6000.205.2.7.1.6 | Integer32 | read-create | The expicit pathid of destid. |
| ROW zxr10P2mpTeDstIDCfgRowStatus | 1.3.6.1.4.1.3902.3.6000.205.2.7.1.100 | RowStatus | read-create | Row status. |
| zxr10P2mpTeLocTnnlTable | 1.3.6.1.4.1.3902.3.6000.205.2.8 | not-accessible | ||
| zxr10P2mpTeLocTnnlEntry | 1.3.6.1.4.1.3902.3.6000.205.2.8.1 | not-accessible | ||
| I32 zxr10P2mpTeLocTnnlIndex | 1.3.6.1.4.1.3902.3.6000.205.2.8.1.1 | Integer32 | not-accessible | P2mp Local tunnel Index. |
| STR zxr10P2mpTeLocTnnlName | 1.3.6.1.4.1.3902.3.6000.205.2.8.1.2 | DisplayString | read-only | P2mp Local tunnel Name . |
| U32 zxr10P2mpTeLocTnnlP2mpID | 1.3.6.1.4.1.3902.3.6000.205.2.8.1.3 | Unsigned32 | read-only | The p2mpid of P2mp Local tunnel . |
| I32 zxr10P2mpTeLocTnnlInuseLspID | 1.3.6.1.4.1.3902.3.6000.205.2.8.1.4 | Integer32 | read-only | The inuselspid of P2mp Local tunnel . |
| TIK zxr10P2mpTeLocTnnlCreationTime | 1.3.6.1.4.1.3902.3.6000.205.2.8.1.5 | TimeTicks | read-only | The creationtime of P2mp Local tunnel. |
| TIK zxr10P2mpTeLocTnnlUpTime | 1.3.6.1.4.1.3902.3.6000.205.2.8.1.6 | TimeTicks | read-only | The uptime of P2mp Local tunnel. |
| INT zxr10P2mpTeLocTnnlOperStatus | 1.3.6.1.4.1.3902.3.6000.205.2.8.1.7 | INTEGER | read-only | The operstatus of P2mp Local tunnel . |
| INT zxr10P2mpTeLocTnnlAdminStatus | 1.3.6.1.4.1.3902.3.6000.205.2.8.1.8 | INTEGER | read-only | The adminstatus of P2mp Local tunnel . |
| zxr10P2mpTeLeafTnnlTable | 1.3.6.1.4.1.3902.3.6000.205.2.9 | not-accessible | ||
| zxr10P2mpTeLeafTnnlEntry | 1.3.6.1.4.1.3902.3.6000.205.2.9.1 | not-accessible | ||
| I32 zxr10P2mpTeLeafTnnlIndex | 1.3.6.1.4.1.3902.3.6000.205.2.9.1.1 | Integer32 | not-accessible | P2mp Leaf tunnel Index. |
| STR zxr10P2mpTeLeafTnnlName | 1.3.6.1.4.1.3902.3.6000.205.2.9.1.2 | DisplayString | read-only | P2mp Leaf tunnel Name . |
| INT zxr10P2mpTeLeafTnnlOperStatus | 1.3.6.1.4.1.3902.3.6000.205.2.9.1.3 | INTEGER | read-only | The operstatus of P2mp root tunnel . |
| zxr10P2mpTeLspTable | 1.3.6.1.4.1.3902.3.6000.205.2.10 | not-accessible | ||
| zxr10P2mpTeLspEntry | 1.3.6.1.4.1.3902.3.6000.205.2.10.1 | not-accessible | ||
| I32 zxr10P2mpTeLspTnnlIndex | 1.3.6.1.4.1.3902.3.6000.205.2.10.1.1 | Integer32 | not-accessible | P2mp Te Lsp Name . |
| U32 zxr10P2mpTeLspP2mpID | 1.3.6.1.4.1.3902.3.6000.205.2.10.1.2 | Unsigned32 | not-accessible | P2mp Te Lsp P2mpId . |
| I32 zxr10P2mpTeLspLSPID | 1.3.6.1.4.1.3902.3.6000.205.2.10.1.3 | Integer32 | not-accessible | P2mp Te Lsp Index. |
| IP zxr10P2mpTeLspIngressID | 1.3.6.1.4.1.3902.3.6000.205.2.10.1.4 | IpAddress | not-accessible | P2mp Te Lsp IngressId. |
| IP zxr10P2mpTeLspPrevHop | 1.3.6.1.4.1.3902.3.6000.205.2.10.1.5 | IpAddress | not-accessible | P2mp Te Lsp PrevHop. |
| U32 zxr10P2mpTeLspBandwith | 1.3.6.1.4.1.3902.3.6000.205.2.10.1.6 | Unsigned32 | read-only | P2mp Te Lsp Bandwith. |
| I32 zxr10P2mpTeLspSetupprio | 1.3.6.1.4.1.3902.3.6000.205.2.10.1.7 | Integer32 | read-only | P2mp Te Lsp Setupprio. |
| I32 zxr10P2mpTeLspHoldprio | 1.3.6.1.4.1.3902.3.6000.205.2.10.1.8 | Integer32 | read-only | P2mp Te Lsp Holdprio. |
| T/F zxr10P2mpTeLspIntegrity | 1.3.6.1.4.1.3902.3.6000.205.2.10.1.9 | TruthValue | read-only | P2mp Te Lsp Integrity. |
| T/F zxr10P2mpTeLspRRO | 1.3.6.1.4.1.3902.3.6000.205.2.10.1.10 | TruthValue | read-only | P2mp Te Lsp RRO. |
| INT zxr10P2mpTeLspResvStyle | 1.3.6.1.4.1.3902.3.6000.205.2.10.1.11 | INTEGER | read-only | P2mp Te Lsp RevStyle. |
| INT zxr10P2mpTeLspRole | 1.3.6.1.4.1.3902.3.6000.205.2.10.1.12 | INTEGER | read-only | P2mp Te Lsp Role. |
| TIK zxr10P2mpTeLspCreationTime | 1.3.6.1.4.1.3902.3.6000.205.2.10.1.13 | TimeTicks | read-only | P2mp Te Lsp CreationTime. |
| INT zxr10P2mpTeLspOperStatus | 1.3.6.1.4.1.3902.3.6000.205.2.10.1.14 | INTEGER | read-only | The operstatus of P2mp Te lsp . |
| INT zxr10P2mpTeLspCrkbackMode | 1.3.6.1.4.1.3902.3.6000.205.2.10.1.15 | INTEGER | read-only | The CrankbackMode of P2mp Te lsp . |
| zxr10P2mpTeSLspTable | 1.3.6.1.4.1.3902.3.6000.205.2.11 | not-accessible | ||
| zxr10P2mpTeSLspEntry | 1.3.6.1.4.1.3902.3.6000.205.2.11.1 | not-accessible | ||
| I32 zxr10P2mpTeSLspTnnlIndex | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.1 | Integer32 | not-accessible | P2mp Te SubLsp TunnelIndex . |
| U32 zxr10P2mpTeSLspP2mpID | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.2 | Unsigned32 | not-accessible | P2mp Te SubLsp P2mpId . |
| I32 zxr10P2mpTeSLspLspID | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.3 | Integer32 | not-accessible | P2mp Te SubLsp LSPId. |
| IP zxr10P2mpTeSLspIngressAddr | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.4 | IpAddress | not-accessible | P2mp Te SubLsp IngressAddr. |
| IP zxr10P2mpTeSLspDestAddr | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.5 | IpAddress | not-accessible | P2mp Te SubLsp DestAddr . |
| IP zxr10P2mpTeSLspPrevHop | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.6 | IpAddress | not-accessible | P2mp Te SubLsp PrevHop . |
| U32 zxr10P2mpTeSLspInLabel | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.7 | Unsigned32 | read-only | P2mp Te SubLsp InLabel. |
| U32 zxr10P2mpTeSLspOutLabel | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.8 | Unsigned32 | read-only | P2mp Te SubLsp OutLabel. |
| STR zxr10P2mpTeSLspInIfName | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.9 | DisplayString | read-only | P2mp Te SubLsp InIfName. |
| STR zxr10P2mpTeSLspOutIfName | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.10 | DisplayString | read-only | P2mp Te SubLsp OutIfName. |
| INT zxr10P2mpTeSLspSrcSubGrpOrigType | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.11 | INTEGER | read-only | P2mp Te SubLsp Src SubGroupOriginType. |
| IP zxr10P2mpTeSLspSrcSubGrpOrigin | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.12 | IpAddress | read-only | P2mp Te SubLsp Src SubGroupOrigin. |
| U32 zxr10P2mpTeSLspSrcSubGrpID | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.13 | Unsigned32 | read-only | P2mp Te SubLsp Src SubGroupID. |
| INT zxr10P2mpTeSLspSubGrpOrigType | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.14 | INTEGER | read-only | P2mp Te SubLsp SubGroupOriginType. |
| IP zxr10P2mpTeSLspSubGrpOrig | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.15 | IpAddress | read-only | P2mp Te SubLsp SubGroupOrigin. |
| U32 zxr10P2mpTeSLspSubGrpID | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.16 | Unsigned32 | read-only | P2mp Te SubLsp SubGroupID. |
| U32 zxr10P2mpTeSLspHopIndex | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.17 | Unsigned32 | read-only | P2mp Te SubLsp hopindex. |
| U32 zxr10P2mpTeSLspChopIndex | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.18 | Unsigned32 | read-only | P2mp Te SubLsp chopindex. |
| U32 zxr10P2mpTeSLspARhopIndex | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.19 | Unsigned32 | read-only | P2mp Te SubLsp arhopindex. |
| INT zxr10P2mpTeSLspRole | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.20 | INTEGER | read-only | P2mp Te SubLsp UpTime. |
| TIK zxr10P2mpTeSLspCreationTime | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.21 | TimeTicks | read-only | P2mp Te SubLsp CreationTime. |
| TIK zxr10P2mpTeSLspUpTime | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.22 | TimeTicks | read-only | P2mp Te SubLsp UpTime. |
| INT zxr10P2mpTeSLspOperStatus | 1.3.6.1.4.1.3902.3.6000.205.2.11.1.23 | INTEGER | read-only | P2mp Te SubLsp OperStatus. |
| zxr10P2mpTeHopTable | 1.3.6.1.4.1.3902.3.6000.205.2.12 | not-accessible | ||
| zxr10P2mpTeHopEntry | 1.3.6.1.4.1.3902.3.6000.205.2.12.1 | not-accessible | ||
| U32 zxr10P2mpTeHopListIndex | 1.3.6.1.4.1.3902.3.6000.205.2.12.1.1 | Unsigned32 | not-accessible | Primary index into this table identifying a particular explicit route object. |
| I32 zxr10P2mpTeHopPathOptionIndex | 1.3.6.1.4.1.3902.3.6000.205.2.12.1.2 | Integer32 | not-accessible | Secondary index into this table identifying a particular group of hops representing a particular configured path. This is otherwise known as a path option. |
| I32 zxr10P2mpTeHopIndex | 1.3.6.1.4.1.3902.3.6000.205.2.12.1.3 | Integer32 | not-accessible | Tertiary index into this table identifying a particular hop. |
| INT zxr10P2mpTeHopAddrType | 1.3.6.1.4.1.3902.3.6000.205.2.12.1.4 | INTEGER | read-only | The Hop Address Type of this tunnel hop. |
| IP zxr10P2mpTeHopIpAddr | 1.3.6.1.4.1.3902.3.6000.205.2.12.1.5 | IpAddress | read-only | The Tunnel Hop Address for this tunnel hop. |
| U32 zxr10P2mpTeHopIpPrefixLen | 1.3.6.1.4.1.3902.3.6000.205.2.12.1.6 | Unsigned32 | read-only | If zxr10P2mpTeHopAddrType is set to ipv4(1) or ipv6(2), then this value will contain an appropriate prefix length for the IP address in object zxr10P2mpTeHopIpAddr. Otherwise this value is irrelevant and should be ignored. |
| U32 zxr10P2mpTeHopAsNumber | 1.3.6.1.4.1.3902.3.6000.205.2.12.1.7 | Unsigned32 | read-only | If zxr10P2mpTeHopAddrType is set to asnumber(3), then this value will contain the AS number of this hop. Otherwise the agent should set this object to zerolength string and the manager should ignore this. |
| U32 zxr10P2mpTeHopAddrUnnum | 1.3.6.1.4.1.3902.3.6000.205.2.12.1.8 | Unsigned32 | read-only | If zxr10P2mpTeHopAddrType is set to unnum(4), then this value will contain the interface identifier of the unnumbered interface for this hop. This object should be used in conjunction with zxr10P2mpTeHopIpAddr which would contain the LSR Router ID in this case. Otherwise the agent should set this object to zero-length string and the manager should ignore this. |
| U32 zxr10P2mpTeHopLspID | 1.3.6.1.4.1.3902.3.6000.205.2.12.1.9 | Unsigned32 | read-only | If zxr10P2mpTeHopAddrType is set to lspid(5), then this value will contain the LSPID of a tunnel of this hop. The present tunnel being configured is tunneled through this hop (using label stacking). This object is otherwise insignificant and should contain a value of 0 to indicate this fact. |
| INT zxr10P2mpTeHopType | 1.3.6.1.4.1.3902.3.6000.205.2.12.1.10 | INTEGER | read-only | Denotes whether this tunnel hop is routed in a strict or loose fashion. The value of this object has no meaning if the zxr10P2mpTeHopInclude object is set to false. |
| T/F zxr10P2mpTeHopInclude | 1.3.6.1.4.1.3902.3.6000.205.2.12.1.11 | TruthValue | read-only | If this value is set to true, then this indicates that this hop must be included in the tunnel's path. If this value is set to 'false', then this hoph must be avoided when calculating the path for this tunnel. The default value of this object is 'true', so that by default all indicated hops are included in the CSPF path computation. If this object is set to 'false' the value of zxr10P2mpTeHopType should be ignored. |
| STR zxr10P2mpTeHopPathOptionName | 1.3.6.1.4.1.3902.3.6000.205.2.12.1.12 | DisplayString | read-only | The description of this series of hops as they relate to the specified path option. The value of this object SHOULD be the same for each hop in the series that comprises a path option. |
| INT zxr10P2mpTeHopEntryPathComp | 1.3.6.1.4.1.3902.3.6000.205.2.12.1.13 | INTEGER | read-only | If this value is set to dynamic, then the user should only specify the source and destination of the path and expect that the CSPF will calculate the remainder of the path. If this value is set to explicit, the user should specify the entire path for the tunnel to take. This path may contain strict or loose hops. Each hop along a specific path SHOULD have this object set to the same value. |
| INT zxr10P2mpTeHopRowStatus | 1.3.6.1.4.1.3902.3.6000.205.2.12.1.100 | INTEGER | read-only | Row status. |
| INT zxr10P2mpTeHopStorageType | 1.3.6.1.4.1.3902.3.6000.205.2.12.1.101 | INTEGER | read-only | The storage type for this Hop entry. |
| zxr10P2mpTeCHopTable | 1.3.6.1.4.1.3902.3.6000.205.2.13 | not-accessible | ||
| zxr10P2mpTeCHopEntry | 1.3.6.1.4.1.3902.3.6000.205.2.13.1 | not-accessible | ||
| U32 zxr10P2mpTeCHopListIndex | 1.3.6.1.4.1.3902.3.6000.205.2.13.1.1 | Unsigned32 | not-accessible | Primary index into this table identifying a particular computed hop list. |
| U32 zxr10P2mpTeCHopIndex | 1.3.6.1.4.1.3902.3.6000.205.2.13.1.2 | Unsigned32 | not-accessible | Secondary index into this table identifying the particular hop. |
| INT zxr10P2mpTeCHopAddrType | 1.3.6.1.4.1.3902.3.6000.205.2.13.1.3 | INTEGER | read-only | The Hop Address Type of this tunnel hop. Note that lspid(5) is a valid option only for tunnels signaled via CRLDP. |
| IP zxr10P2mpTeCHopIpAddr | 1.3.6.1.4.1.3902.3.6000.205.2.13.1.4 | IpAddress | read-only | The Tunnel Hop Address for this tunnel hop. The type of this address is determined by the value of the corresponding zxr10r10MplsTunnelCHopAddrType. If zxr10r10MplsTunnelCHopAddrType is set to unnum(4), then this value will contain the LSR Router ID of the unnumbered interface. Otherwise the agent should set this object to the zero-length string and the manager SHOULD ignore this object. |
| U32 zxr10P2mpTeCHopIpPrefixLen | 1.3.6.1.4.1.3902.3.6000.205.2.13.1.5 | Unsigned32 | read-only | If zxr10P2mpTeCHopAddrType is set to ipv4(1) or ipv6(2), then this value will contain an appropriate prefix length for the IP address in object zxr10P2mpTeCHopIpAddr. Otherwise this value is irrelevant and should be ignored. |
| U32 zxr10P2mpTeCHopAsNumber | 1.3.6.1.4.1.3902.3.6000.205.2.13.1.6 | Unsigned32 | read-only | If zxr10P2mpTeCHopAddrType is set to asnumber(3), then this value will contain the AS number of this hop. Otherwise the agent should set this object to zero-length string and the manager should ignore this. |
| U32 zxr10P2mpTeCHopAddrUnnum | 1.3.6.1.4.1.3902.3.6000.205.2.13.1.7 | Unsigned32 | read-only | If zxr10P2mpTeCHopAddrType is set to unnum(4), then this value will contain the unnumbered interface identifier of this hop. This object should be used in conjunction with zxr10P2mpTeCHopIpAddr which would contain the LSR Router ID in this case. Otherwise the agent should set this object to zerolength string and the manager should ignore this. |
| U32 zxr10P2mpTeCHopLspID | 1.3.6.1.4.1.3902.3.6000.205.2.13.1.8 | Unsigned32 | read-only | If zxr10P2mpTeCHopAddrType is set to lspid(5), then his value will contain the LSP ID of this hop. his object is otherwise insignificant and should contain a value of 0 to indicate this fact. |
| INT zxr10P2mpTeCHopType | 1.3.6.1.4.1.3902.3.6000.205.2.13.1.9 | INTEGER | read-only | Denotes whether this is tunnel hop is routed in a strict or loose fashion. |
| zxr10P2mpTeARHopTable | 1.3.6.1.4.1.3902.3.6000.205.2.14 | not-accessible | ||
| zxr10P2mpTeARHopEntry | 1.3.6.1.4.1.3902.3.6000.205.2.14.1 | not-accessible | ||
| U32 zxr10P2mpTeARHopListIndex | 1.3.6.1.4.1.3902.3.6000.205.2.14.1.1 | Unsigned32 | not-accessible | Primary index into this table identifying a particular recorded hop list. |
| U32 zxr10P2mpTeARHopIndex | 1.3.6.1.4.1.3902.3.6000.205.2.14.1.2 | Unsigned32 | not-accessible | Secondary index into this table identifying the particular hop. |
| INT zxr10P2mpTeARHopAddrType | 1.3.6.1.4.1.3902.3.6000.205.2.14.1.3 | INTEGER | read-only | The Hop Address Type of this tunnel hop. ote that lspid(5) is a valid option only for tunnels signaled via CRLDP. |
| IP zxr10P2mpTeARHopIpAddr | 1.3.6.1.4.1.3902.3.6000.205.2.14.1.4 | IpAddress | read-only | The Tunnel Hop Address for this tunnel hop. The type of this address is determined by the value of the corresponding zxr10r10MplsTunnelARHopAddrType. If zxr10P2mpTeARHopAddrType is set to unnum(4), then this value contains the LSR Router ID of the unnumbered interface. Otherwise the agent SHOULD set this object to the zero-length string and the manager should ignore this object. |
| U32 zxr10P2mpTeARHopAddrUnnum | 1.3.6.1.4.1.3902.3.6000.205.2.14.1.5 | Unsigned32 | read-only | If zxr10P2mpTeARHopAddrType is set to unnum(4), then this value will contain the interface identifier of the unnumbered interface for this hop. This object should be used in conjunction with zxr10P2mpTeARHopIpAddr which would contain the LSR Router ID in this case. Otherwise the agent should set this object to zero-length string and the manager should ignore this. |
| U32 zxr10P2mpTeARHopLspID | 1.3.6.1.4.1.3902.3.6000.205.2.14.1.6 | Unsigned32 | read-only | If zxr10P2mpTeARHopAddrType is set to lspid(5), then this value will contain the LSP ID of this hop. This object is otherwise insignificant and should contain a value of 0 to indicate this fact. |
| zxr10P2mpTeFrrDBTable | 1.3.6.1.4.1.3902.3.6000.205.2.15 | not-accessible | ||
| zxr10P2mpTeFrrDBEntry | 1.3.6.1.4.1.3902.3.6000.205.2.15.1 | not-accessible | ||
| U32 zxr10P2mpTeFrrProtectedIfIndex | 1.3.6.1.4.1.3902.3.6000.205.2.15.1.1 | Unsigned32 | not-accessible | P2MP TE FRR Protected Interface Index. |
| I32 zxr10P2mpTeFrrPriTunnelIndex | 1.3.6.1.4.1.3902.3.6000.205.2.15.1.2 | Integer32 | not-accessible | P2MP TE FRR Primary Tunnel Index. |
| U32 zxr10P2mpTeFrrPriTunnelP2mpID | 1.3.6.1.4.1.3902.3.6000.205.2.15.1.3 | Unsigned32 | not-accessible | P2MP TE FRR Primary Tunnel P2MP ID. |
| IP zxr10P2mpTeFrrPriTunnelIngressID | 1.3.6.1.4.1.3902.3.6000.205.2.15.1.4 | IpAddress | not-accessible | P2MP TE FRR Primary Tunnel IngressID. |
| I32 zxr10P2mpTeFrrPriTunnelLspID | 1.3.6.1.4.1.3902.3.6000.205.2.15.1.5 | Integer32 | not-accessible | P2MP TE FRR Primary Tunnel LspId. |
| IP zxr10P2mpTeFrrPriTunnelPrevHop | 1.3.6.1.4.1.3902.3.6000.205.2.15.1.6 | IpAddress | not-accessible | P2MP TE FRR Primary Tunnel PrevHop. |
| IP zxr10P2mpTeFrrPriTunnelNextHop | 1.3.6.1.4.1.3902.3.6000.205.2.15.1.7 | IpAddress | not-accessible | P2MP TE FRR Primary Tunnel NextHop. |
| I32 zxr10P2mpTeFrrBackupTunnelIndex | 1.3.6.1.4.1.3902.3.6000.205.2.15.1.8 | Integer32 | read-only | P2MP TE FRR Backup tunnel index. |
| STR zxr10P2mpTeFrrProtectedIfName | 1.3.6.1.4.1.3902.3.6000.205.2.15.1.9 | DisplayString | read-only | P2MP TE FRR Protected Interface Name. |
| U32 zxr10P2mpTeFrrInnerLabel | 1.3.6.1.4.1.3902.3.6000.205.2.15.1.10 | Unsigned32 | read-only | P2MP TE FRR Inner Label. |
| INT zxr10P2mpTeFrrStatus | 1.3.6.1.4.1.3902.3.6000.205.2.15.1.11 | INTEGER | read-only | P2MP TE FRR Status. |
| zxr10P2mpTeTraps | 1.3.6.1.4.1.3902.3.6000.205.3 | |||
| zxr10P2mpTeConformance | 1.3.6.1.4.1.3902.3.6000.205.4 |
RFC description
Point-to-multipoint traffic engineering management for ZTE ZXR10 routers.
Start monitoring ZTE ZXR10 MPLS core router (P2MP TE tunnel destination-leaf/bandwidth config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.