ZXR10-MPLSTE-STATIC-LSP-MIB

All MIBs › ZXR10-MPLSTE-STATIC-LSP-MIB

Last Updated: 2005-07-26

Category: ZTE ZXR10 MPLS and Traffic Engineering

Description: Defines ZTE ZXR10 MPLS TE static LSP configuration for manually provisioned label-switched paths.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ZXR10-MPLSTE-STATIC-LSP-MIB?

ZXR10-MPLSTE-STATIC-LSP-MIB is a ZTE private module for ZXR10 routers that defines configuration objects for statically (manually) provisioned MPLS Traffic Engineering LSPs, as opposed to dynamically signaled ones. It exposes configuration data describing static LSP paths, hop lists, and label bindings rather than dynamic signaling statistics. Its monitoring role centers on confirming the software/configuration status of these manually defined LSPs, letting an administrator verify a static path is correctly configured and active, which matters because static LSPs have no dynamic re-signaling to recover from a bad configuration. It depends on general MPLS-TE conventions and label-space objects defined in standard MPLS-TE and MPLS-LSR MIBs. It is deployed on ZXR10 core or edge routers where traffic engineering paths are pinned by the operator for deterministic routing rather than left to dynamic constraint-based routing. Engineers can download the ZXR10-MPLSTE-STATIC-LSP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ZXR10-MPLSTE-STATIC-LSP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ZTE ZXR10 MPLS traffic-engineering router

Monitoring Examples

No sample objects were provided for this MIB, so specific object names cannot be cited; based on its purpose, an operator would poll the static LSP configuration and hop-path objects to confirm a pinned traffic-engineering path still matches its intended route and label assignments. A discrepancy between configured and actual forwarding state would indicate the static LSP has failed or been overridden, requiring manual correction since no dynamic signaling will repair it.

What Can Be Monitored

static LSP path configuration
label binding for static LSP
static LSP operational status

Imported Objects

From SNMPv2-SMI

IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString

From ZXR10-SMI

mplsTeStaticLsp

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
mplsTeStaticLspMIB	1.3.6.1.4.1.3902.3.320.1
mplsTeStaticLspNotifications	1.3.6.1.4.1.3902.3.320.1.0
NTF mplsTeStaticLocalLspUp	1.3.6.1.4.1.3902.3.320.1.0.1			This notification is generated when a mplsStaticLocalLspTunnelStatus object for one of the configured static tunnels is about to leave the down state and transition into up state.
NTF mplsTeStaticLocalLspDown	1.3.6.1.4.1.3902.3.320.1.0.2			This notification is generated when a mplsStaticLocalLspTunnelStatus object for one of the configured static tunnels is about to leave the up state and transition into down state.
NTF mplsTeStaticRemoteLspUp	1.3.6.1.4.1.3902.3.320.1.0.3			This notification is generated when a mplsStaticRemoteLspTunnelStatus object for one of the configured static tunnels is about to leave the down state and transition into up state.
NTF mplsTeStaticRemoteLspDown	1.3.6.1.4.1.3902.3.320.1.0.4			This notification is generated when a mplsStaticRemoteLspTunnelStatus object for one of the configured static tunnels is about to leave the up state and transition into down state.
mplsTeStaticLocalLspObjects	1.3.6.1.4.1.3902.3.320.1.1
mplsTeStaticLocalLspTable	1.3.6.1.4.1.3902.3.320.1.1.1		not-accessible	Local static tunnel information query table.
mplsTeStaticLocalLspEntry	1.3.6.1.4.1.3902.3.320.1.1.1.1		not-accessible	Local static tunnel instance.
U32 mplsStaticLocalLspTunnelId	1.3.6.1.4.1.3902.3.320.1.1.1.1.1	Unsigned32	read-only	Uniquely identifies a set of static tunnel instances between a pair of ingress and egress LSRs.
INT mplsStaticLocalLspTunnelType	1.3.6.1.4.1.3902.3.320.1.1.1.1.2	INTEGER	read-only	Specifies the type of a static tunnel.
IP mplsStaticLocalLspIngressLSRId	1.3.6.1.4.1.3902.3.320.1.1.1.1.3	IpAddress	read-only	Identity of the ingress LSR .
IP mplsStaticLocalLspEgressLSRId	1.3.6.1.4.1.3902.3.320.1.1.1.1.4	IpAddress	read-only	Identity of the egress LSR .
IP mplsStaticLocalLspNexthop	1.3.6.1.4.1.3902.3.320.1.1.1.1.5	IpAddress	read-only	The next hop of this LSR.
U32 mplsStaticLocalLsp0utIntf	1.3.6.1.4.1.3902.3.320.1.1.1.1.6	Unsigned32	read-only	Out interface of local static lsp.
STR mplsStaticLocalLspOutIfName	1.3.6.1.4.1.3902.3.320.1.1.1.1.7	DisplayString	read-only	Out interface name of local static lsp.
U32 mplsStaticLocalLspOutLabel	1.3.6.1.4.1.3902.3.320.1.1.1.1.8	Unsigned32	read-only	Out label of local static lsp.
U32 mplsStaticLocalLspBackuplspId	1.3.6.1.4.1.3902.3.320.1.1.1.1.9	Unsigned32	read-only	The index of tunnel which protecting the mplsStaticLocalLsp0utIntf.
INT mplsStaticLocalLspBackupLspstatus	1.3.6.1.4.1.3902.3.320.1.1.1.1.10	INTEGER	read-only	Specifies the state of the protecting tunnel as specified by mplsStaticLocalLspBackuplspId.
INT mplsStaticLocalLspBackeuplspProtectMode	1.3.6.1.4.1.3902.3.320.1.1.1.1.11	INTEGER	read-only	Specifies the protect mode of the protecting tunnel.
INT mplsStaticLocalLspNodeRole	1.3.6.1.4.1.3902.3.320.1.1.1.1.12	INTEGER	read-only	This value signifies the role that this static tunnel entry/instance represents.
U32 mplsStaticLocalLspBandwidth	1.3.6.1.4.1.3902.3.320.1.1.1.1.13	Unsigned32	read-only	This value identifies the bandwidth of this static tunnel.
INT mplsStaticLocalLspTunnelStatus	1.3.6.1.4.1.3902.3.320.1.1.1.1.14	INTEGER	read-only	This value identifies actual operational status of this static tunnel.
INT mplsStaticLocalLspTunnelAdminStatus	1.3.6.1.4.1.3902.3.320.1.1.1.1.15	INTEGER	read-only	This value identifies the administrator status of this static tunnel.
U32 mplsStaticLocalLspRvsInIntf	1.3.6.1.4.1.3902.3.320.1.1.1.1.16	Unsigned32	read-only	In interface of reverse Local static lsp.
STR mplsStaticLocalLspRvsInIfName	1.3.6.1.4.1.3902.3.320.1.1.1.1.17	DisplayString	read-only	In interface name of reverse Local static lsp.
U32 mplsStaticLocalLspRvsInLabel	1.3.6.1.4.1.3902.3.320.1.1.1.1.18	Unsigned32	read-only	In label of reverse Local static lsp.
mplsTeStaticRemoteLspObjects	1.3.6.1.4.1.3902.3.320.1.2
mplsTeStaticRemoteLspTable	1.3.6.1.4.1.3902.3.320.1.2.1		not-accessible	Remote static tunnel information query table.
mplsTeStaticRemoteLspEntry	1.3.6.1.4.1.3902.3.320.1.2.1.1		not-accessible	Remote static tunnel instance .
U32 mplsStaticRemoteLspTunnelId	1.3.6.1.4.1.3902.3.320.1.2.1.1.1	Unsigned32	read-only	Uniquely identifies a set of static tunnel instances between a pair of ingress and egress LSRs.
INT mplsStaticRemoteLspTunnelType	1.3.6.1.4.1.3902.3.320.1.2.1.1.2	INTEGER	read-only	Specifies the type of a static tunnel.
IP mplsStaticRemoteLspIngressLSRId	1.3.6.1.4.1.3902.3.320.1.2.1.1.3	IpAddress	read-only	Identity of the ingress LSR .
IP mplsStaticRemoteLspEgressLSRId	1.3.6.1.4.1.3902.3.320.1.2.1.1.4	IpAddress	read-only	Identity of the egress LSR .
IP mplsStaticRemoteLspNexthop	1.3.6.1.4.1.3902.3.320.1.2.1.1.5	IpAddress	read-only	The next hop of this static lsp.
U32 mplsStaticRemoteLsp0utIntf	1.3.6.1.4.1.3902.3.320.1.2.1.1.6	Unsigned32	read-only	Out interface of Remote static lsp.
STR mplsStaticRemoteLspOutIfName	1.3.6.1.4.1.3902.3.320.1.2.1.1.7	DisplayString	read-only	Out interface name of Remote static lsp.
U32 mplsStaticRemoteLspOutLabel	1.3.6.1.4.1.3902.3.320.1.2.1.1.8	Unsigned32	read-only	Out label of Remote static lsp.
U32 mplsStaticRemoteLspInIntf	1.3.6.1.4.1.3902.3.320.1.2.1.1.9	Unsigned32	read-only	In interface of Remote static lsp.
STR mplsStaticRemoteLspInIfName	1.3.6.1.4.1.3902.3.320.1.2.1.1.10	DisplayString	read-only	In interface name of Remote static lsp.
U32 mplsStaticRemoteLspInLabel	1.3.6.1.4.1.3902.3.320.1.2.1.1.11	Unsigned32	read-only	In label of Remote static lsp.
INT mplsStaticRemoteLspNodeRole	1.3.6.1.4.1.3902.3.320.1.2.1.1.12	INTEGER	read-only	This value signifies the role that this static tunnel entry/instance represents.
U32 mplsStaticRemoteLspBandwidth	1.3.6.1.4.1.3902.3.320.1.2.1.1.13	Unsigned32	read-only	This value identifies the bandwidth of this static tunnel.
INT mplsStaticRemoteLspTunnelStatus	1.3.6.1.4.1.3902.3.320.1.2.1.1.14	INTEGER	read-only	This value identifies actual operational status of this static tunnel.
IP mplsStaticRemoteLspRvsNexthop	1.3.6.1.4.1.3902.3.320.1.2.1.1.15	IpAddress	read-only	The next hop of reverse static lsp.
U32 mplsStaticRemoteLspRvs0utIntf	1.3.6.1.4.1.3902.3.320.1.2.1.1.16	Unsigned32	read-only	Out interface of Remote reverse static lsp.
STR mplsStaticRemoteLspRvsOutIfName	1.3.6.1.4.1.3902.3.320.1.2.1.1.17	DisplayString	read-only	Out interface name of Remote reverse static lsp.
U32 mplsStaticRemoteLspRvsOutLabel	1.3.6.1.4.1.3902.3.320.1.2.1.1.18	Unsigned32	read-only	Out label of Remote reverse static lsp.
U32 mplsStaticRemoteLspRvsInIntf	1.3.6.1.4.1.3902.3.320.1.2.1.1.19	Unsigned32	read-only	In interface of Remote reverse static lsp.
STR mplsStaticRemoteLspRvsInIfName	1.3.6.1.4.1.3902.3.320.1.2.1.1.20	DisplayString	read-only	In interface name of Remote reverse static lsp.
U32 mplsStaticRemoteLspRvsInLabel	1.3.6.1.4.1.3902.3.320.1.2.1.1.21	Unsigned32	read-only	In label of Remote reverse static lsp.

RFC description

Defines SNMP management objects for MPLS TE (Multi-Protocol Label Switching Traffic Engineering) static Label Switched Paths (LSPs) on ZTE ZXR10 networking equipment, supporting features such as TE tunnel calculation using CSPF algorithms.

Start monitoring ZTE ZXR10 MPLS traffic-engineering router (static-LSP path/hop-list config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ZXR10-MPLSTE-STATIC-LSP-MIB

What Is ZXR10-MPLSTE-STATIC-LSP-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description