ZXR10-MPLS-L2VPN

All MIBs › ZXR10-MPLS-L2VPN

Organization: ZTE Corporation

Last Updated: 2005-07-26

Category: ZTE ZXR10 L2VPN and L3VPN

Description: Manages ZTE ZXR10 MPLS-based Layer 2 VPN services including pseudowire and VPLS configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ZXR10-MPLS-L2VPN?

ZXR10-MPLS-L2VPN is a ZTE proprietary SNMP module (documented against ZXROS v4.6.03) for the ZXR10 platform that manages MPLS-based Layer 2 VPN services, including pseudowire configuration and VPLS (Virtual Private LAN Service) setups. It exposes configuration data describing pseudowires, VPLS instances, and their associated attachment circuits rather than environmental hardware metrics. This MIB supports monitoring the software/service status of MPLS L2VPN offerings on the device, letting an operator confirm pseudowires and VPLS instances are provisioned and in the expected operational state, which is critical for delivering carrier Ethernet services reliably. It is conceptually layered on top of core MPLS forwarding and likely complements ZXR10 MPLS-TE and L2VPN-object MIBs for a complete picture of the service. It is deployed on ZTE ZXR10 routers acting as PE devices in carrier MPLS networks delivering point-to-point or multipoint Ethernet services, and engineers configuring these PE routers often begin with a ZXR10-MPLS-L2VPN download to load the module into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ZXR10-MPLS-L2VPN. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ZTE ZXR10 router (MPLS PE device)

Monitoring Examples

No object names were captured for this MIB, so a specific table cannot be honestly cited; in practice an operator would poll the pseudowire/VPLS instance tables to confirm each service shows an established/up state, noticing a service-impacting problem if a pseudowire remains down or flaps repeatedly.

What Can Be Monitored

pseudowire operational state
VPLS instance status
attachment circuit configuration
L2VPN service provisioning state

Imported Objects

From RFC1155-SMI

IpAddress

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

TEXTUAL-CONVENTION

From ZXR10-SMI

zxr10L2vpn

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
zxr10MplsL2vpnMIB	1.3.6.1.4.1.3902.3.104.1			ZXROS v4.6.03 Mpls L2vpn query and configuration MIB
zxr10MplsL2vpnObjects	1.3.6.1.4.1.3902.3.104.1.0
zxr10MplsL2vpnInstanceTable	1.3.6.1.4.1.3902.3.104.1.0.1		not-accessible	Mpls L2vpn instance query table
zxr10MplsL2vpnInstanceEntry	1.3.6.1.4.1.3902.3.104.1.0.1.1		not-accessible	Information of Mpls L2vpn instance configured on a PE
MPL zxr10MplsL2vpnInstanceType	1.3.6.1.4.1.3902.3.104.1.0.1.1.1	MplsL2vpnType	read-only	Mpls L2vpn type,including:vpls,vpws and ipls
U32 zxr10MplsL2vpnInstanceVCId	1.3.6.1.4.1.3902.3.104.1.0.1.1.2	Unsigned32	read-only	Mpls L2vpn unique vcid value on a PE.
STR zxr10MplsL2vpnInstanceVpnName	1.3.6.1.4.1.3902.3.104.1.0.1.1.3	DisplayString	read-only	Name specified for each configured Mpls L2vpn.
U32 zxr10MplsL2vpnPwCounts	1.3.6.1.4.1.3902.3.104.1.0.1.1.4	Unsigned32	read-only	Number of PWs that belongs to a certain Mpls L2vpn
zxr10MplsL2vpnPWObjects	1.3.6.1.4.1.3902.3.104.1.1
zxr10MplsL2vpnPWTable	1.3.6.1.4.1.3902.3.104.1.1.1		not-accessible	Mpls L2vpn PW query table.
zxr10MplsL2vpnPWEntry	1.3.6.1.4.1.3902.3.104.1.1.1.1		not-accessible	Informatin of Mpls L2vpn PW configured on a PE.
U32 zxr10MplsL2vpnPWVcId	1.3.6.1.4.1.3902.3.104.1.1.1.1.1	Unsigned32	read-only	VcId of Mpls L2vpn that PW belongs to.It can't be zero.
MPL zxr10MplsL2vpnPWType	1.3.6.1.4.1.3902.3.104.1.1.1.1.2	MplsL2vpnPWType	read-only	Type of PW:hub or spoke,used in H-VPLS.
MPL zxr10MplsL2vpnPWEncapsulationType	1.3.6.1.4.1.3902.3.104.1.1.1.1.3	MplsL2vpnPWEncapsulationType	read-only	Mpls L2vpn PW encapsulation type.
I32 zxr10MplsL2vpnPWVlanid	1.3.6.1.4.1.3902.3.104.1.1.1.1.4	Integer32	read-only	if zxr10MplsL2vpnPWEncapsulationType is eth-vlan type,this value represents vlan id encapsulated for L2vpn interface.It will be zero otherwise.
MPL zxr10MplsL2vpnPWPsnType	1.3.6.1.4.1.3902.3.104.1.1.1.1.5	MplsL2vpnPWPsnType	read-only	Type of external tunnel for this PW to be carried on.
U32 zxr10MplsL2vpnPWTunnelid	1.3.6.1.4.1.3902.3.104.1.1.1.1.6	Unsigned32	read-only	If zxr10MplsL2vpnPWPsnType is TE tunnel,this value represents Id of TE tunnel for this PW to be carried on. It will be zero otherwise.
U32 zxr10MplsL2vpnPWInlabel	1.3.6.1.4.1.3902.3.104.1.1.1.1.7	Unsigned32	read-only	The PW internal label used in the inbound direction,ie label locally allocated. If the label is not yet known,the object should return a value of 0xFFFFFFFF.
U32 zxr10MplsL2vpnPWOutlabel	1.3.6.1.4.1.3902.3.104.1.1.1.1.8	Unsigned32	read-only	The PW internal label used in the outbound direction,ie label allocated by remote peer.If the label is not yet known,the object should return a value of 0xFFFFFFFF.
MPL zxr10MplsL2vpnPWCbit	1.3.6.1.4.1.3902.3.104.1.1.1.1.9	MplsL2vpnPWCbit	read-only	Defines if the control word will be sent with each packet by the local node.
MPL zxr10MplsL2vpnPWStatus	1.3.6.1.4.1.3902.3.104.1.1.1.1.10	MplsL2vpnPWStatus	read-only	If PW has finished negotiation with remote peer including internal label and other parameters,then PW will be in established status.
U32 zxr10MplsL2vpnPWLocalGroupId	1.3.6.1.4.1.3902.3.104.1.1.1.1.11	Unsigned32	read-only	Used in the Group ID field sent to peer within the maintenance protocol used for PW setup.
MPL zxr10MplsL2vpnPWLocalEncapsulationType	1.3.6.1.4.1.3902.3.104.1.1.1.1.12	MplsL2vpnPWEncapsulationType	read-only	Local Mpls L2vpn PW encapsulation type.
U32 zxr10MplsL2vpnPWLocalLabel	1.3.6.1.4.1.3902.3.104.1.1.1.1.13	Unsigned32	read-only	PW internal label locally allocated.If the label is not yet known, the object should return a value of 0xFFFFFFFF.
MPL zxr10MplsL2vpnPWLocalCbit	1.3.6.1.4.1.3902.3.104.1.1.1.1.14	MplsL2vpnPWCbit	read-only	Local configuration of the control word.
STR zxr10MplsL2vpnPWLocalPortName	1.3.6.1.4.1.3902.3.104.1.1.1.1.15	DisplayString	read-only	Name of local interface that PW has been configured on.
IP zxr10MplsL2vpnPWLocalRouterId	1.3.6.1.4.1.3902.3.104.1.1.1.1.16	IpAddress	read-only	Router ID of local PE.
U32 zxr10MplsL2vpnPWLocalIfMtu	1.3.6.1.4.1.3902.3.104.1.1.1.1.17	Unsigned32	read-only	Locally supported MTU size over the interface associated with the PW.
U32 zxr10MplsL2vpnPWRemoteGroupId	1.3.6.1.4.1.3902.3.104.1.1.1.1.18	Unsigned32	read-only	Obtained from the Group ID field as received via the signaling protocol used for PW setup.
MPL zxr10MplsL2vpnPWRemoteEncapsulationType	1.3.6.1.4.1.3902.3.104.1.1.1.1.19	MplsL2vpnPWEncapsulationType	read-only	Remote Mpls L2vpn PW encapsulation type.
U32 zxr10MplsL2vpnPWRemoteLabel	1.3.6.1.4.1.3902.3.104.1.1.1.1.20	Unsigned32	read-only	PW internal label allocated by remote peer.If the label is not yet known, the object should return a value of 0xFFFFFFFF.
MPL zxr10MplsL2vpnPWRemoteCbit	1.3.6.1.4.1.3902.3.104.1.1.1.1.21	MplsL2vpnPWCbit	read-only	Remote configuration of the control word.
STR zxr10MplsL2vpnPWRemotePortName	1.3.6.1.4.1.3902.3.104.1.1.1.1.22	DisplayString	read-only	Name of remote interface that PW has been configured on.
IP zxr10MplsL2vpnPWRemoteRouterId	1.3.6.1.4.1.3902.3.104.1.1.1.1.23	IpAddress	read-only	Router ID of remote PE.
U32 zxr10MplsL2vpnPWRemoteIfMtu	1.3.6.1.4.1.3902.3.104.1.1.1.1.24	Unsigned32	read-only	Supported MTU size of remote peer over the interface associated with the PW.
zxr10MplsL2vpnVpwsIfObjects	1.3.6.1.4.1.3902.3.104.1.2
zxr10MplsL2vpnVpwsIfTable	1.3.6.1.4.1.3902.3.104.1.2.1		not-accessible	Mpls L2vpn instance query table
zxr10MplsL2vpnVpwsIfEntry	1.3.6.1.4.1.3902.3.104.1.2.1.1		not-accessible	Information of Mpls L2vpn instance configured on a PE
NUM zxr10MplsL2vpnVpwsIfIndex	1.3.6.1.4.1.3902.3.104.1.2.1.1.1	InterfaceIndex	read-only	Index of the VPWS configuration interface.
STR zxr10MplsL2vpnVpwsIfName	1.3.6.1.4.1.3902.3.104.1.2.1.1.2	DisplayString	read-only	Name of the VPWS configuration interface.
MPL zxr10MplsL2vpnVpwsIfEncapsulationType	1.3.6.1.4.1.3902.3.104.1.2.1.1.3	MplsL2vpnPWEncapsulationType	read-only	Encapsulation type of the VPWS configuration interface.
U32 zxr10MplsL2vpnVpwsIfVcid	1.3.6.1.4.1.3902.3.104.1.2.1.1.4	Unsigned32	read-only	Vcid of the VPWS configured on this interface.
MPL zxr10MplsL2vpnVpwsIfVpnType	1.3.6.1.4.1.3902.3.104.1.2.1.1.5	MplsL2vpnType	read-only	Type of the L2VPN configured on this interface.
zxr10MplsL2vpnNotifications	1.3.6.1.4.1.3902.3.104.1.3
NTF mplsL2vpnGenericInterfaceTrap	1.3.6.1.4.1.3902.3.104.1.3.1			When one of following conditions happens: (1)Admini,phy or protocol status of a interface is down and it has no children. (2)Interface is off and it has no children. (3)Encapsulation of a interface has changed. (4)MTU of a interface has changed. this type of Trap pdu will be sent.There is only one VPWS type VC affected.
NTF mplsL2vpnMatchInterfaceTrap	1.3.6.1.4.1.3902.3.104.1.3.2			When one of following conditions happens: (1)Admini,phy or protocol status of a interface is down and it has children. (2)Interface is off and it has children. this type of Trap pdu will be sent.
NTF mplsL2vpnGenericProtocolTrap	1.3.6.1.4.1.3902.3.104.1.3.3			When one of following conditions happens: (1)Receives a VC label withdraw message from remote peer. (2)Deletes a VPWS VC. (3)Delete a VPLS peer. (4)Protocol patameters negotiation fails during VC setup. this type of Trap pdu will be sent.
NTF mplsL2vpnSessionDownTrap	1.3.6.1.4.1.3902.3.104.1.3.4			When session to VC peer is down,all the VC that have been bound to mpls Lsp Tunnel will be down;this kind of trap will be sent.
NTF mplsL2vpnVplsDeleteTrap	1.3.6.1.4.1.3902.3.104.1.3.5			When delete a VPLS instance.,this kind of trap will be sent.
NTF mplsL2vpnLinkTrap	1.3.6.1.4.1.3902.3.104.1.3.6			When one of following conditions happens: (1)The PSN route is off. (2)Can't find outer mpls tunnel label. (3)Can't find outer TE tunnel label. this type of Trap pdu will be sent.
NTF mplsL2vpnPsnRouteDownTrap	1.3.6.1.4.1.3902.3.104.1.3.7			When PSN route between PE is down,all the VC between them will be down; this type of Trap pdu will be sent.
NTF mplsL2vpnTETunnelDownTrap	1.3.6.1.4.1.3902.3.104.1.3.8			When one TE Tunnel between is dwon,all the VC between them which has been bound to this tunnel will be down;this type of Trap pdu will be sent
zxr10MplsL2vpnTrapObjects	1.3.6.1.4.1.3902.3.104.1.4
NUM zxr10MplsL2vpnTrapIfIndex	1.3.6.1.4.1.3902.3.104.1.4.1	InterfaceIndex	read-only	If a L2vpn configuration interface is down,a interface down trap pdu will be sent;zxr10MplsL2vpnTrapIfIndex is index of this interface in if table.
STR zxr10MplsL2vpnTrapIfName	1.3.6.1.4.1.3902.3.104.1.4.2	DisplayString	read-only	If a L2vpn configuration interface is down,a interface down trap will be sent;zxr10MplsL2vpnTrapIfName is name of this interface.
MPL zxr10MplsL2vpnTrapLevel	1.3.6.1.4.1.3902.3.104.1.4.3	MplsL2vpnTrapLevel	read-only	Alerting level of Trap pdu.
MPL zxr10MplsL2vpnTrapDetail	1.3.6.1.4.1.3902.3.104.1.4.4	MplsL2vpnTrapDetail	read-only	Detailed information of Trap arising.
U32 zxr10MplsL2vpnTrapVcid	1.3.6.1.4.1.3902.3.104.1.4.5	Unsigned32	read-only	Vcid of L2vpn affected.
IP zxr10MplsL2vpnTrapPeerAddress	1.3.6.1.4.1.3902.3.104.1.4.6	IpAddress	read-only	Peer Address of VC affected.
MPL zxr10MplsL2vpnTrapVpnType	1.3.6.1.4.1.3902.3.104.1.4.7	MplsL2vpnType	read-only	Peer Address of VC affected.
U32 zxr10MplsL2vpnTrapTETunnelId	1.3.6.1.4.1.3902.3.104.1.4.8	Unsigned32	read-only	TE Tunnel Id which VC has been bound to.

RFC description

Configures and queries MPLS Layer 2 VPN settings for ZTE ZXR10 routers.

Start monitoring ZTE ZXR10 router (MPLS PE device) (pseudowire/VPLS instance provisioning status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ZXR10-MPLS-L2VPN

What Is ZXR10-MPLS-L2VPN?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description