All MIBs › XYPLEX-CONCATENATED-MIB
Category: Xylogics and Xyplex Terminal Servers
Description:
Provides Xyplex consolidated MIB combining common management objects across multiple Xyplex modules.
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| NetworkAddress | |
| TimeTicks | |
| enterprises | |
| experimental | |
| mgmt |
What Is XYPLEX-CONCATENATED-MIB?
XYPLEX-CONCATENATED-MIB is a vendor MIB from Xyplex, a terminal-server/network-access equipment maker later part of MRV Communications, that concatenates common management objects shared across several Xyplex product-specific MIB modules into a single combined module. Rather than defining a distinct feature area of its own, it acts as an umbrella/compatibility module bundling definitions used elsewhere in the Xyplex MIB set, so its content generally mirrors whatever common system, interface, and configuration objects Xyplex products expose. Because it is a concatenation/compatibility module, its practical monitoring value depends entirely on which underlying Xyplex object groups it pulls in, typically general device identification, interface, and configuration status rather than a distinct new data category. It is inherently dependent on the individual Xyplex product MIBs it aggregates. It would be used wherever Xyplex terminal servers or network-access devices are managed and a management station needs a single combined MIB file instead of loading each Xyplex module separately. Engineers can download the XYPLEX-CONCATENATED-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in XYPLEX-CONCATENATED-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Xyplex (MRV Communications) terminal server / network access device
Monitoring Examples
No object names or module description text were provided for this MIB, so a concrete polling example or specific monitorable parameters can't be honestly grounded; as a concatenated/umbrella module it would expose whichever common Xyplex system and interface objects are aggregated into it, but which specific objects those are cannot be determined from the available information.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| mib_2 | 1.3.6.1.2.1 | |||
| system | 1.3.6.1.2.1.1 | |||
| STR sysDescr | 1.3.6.1.2.1.1.1 | DisplayString | read-only | A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software. It is mandatory that this only contain printable ASCII characters. |
| OID sysObjectID | 1.3.6.1.2.1.1.2 | OBJECT IDENTIFIER | read-only | The vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determining `what kind of box' is being managed. For example, if vendor `Flintstones, Inc.' was assigned the subtree 1.3.6.1.4.1.4242, it could assign the identifier 1.3.6.1.4.1.4242.1.1 to its `Fred Router'. |
| TIK sysUpTime | 1.3.6.1.2.1.1.3 | TimeTicks | read-only | The time (in hundredths of a second) since the network management portion of the system was last re-initialized. |
| STR sysContact | 1.3.6.1.2.1.1.4 | DisplayString | read-write | The textual identification of the contact person for this managed node, together with information on how to contact this person. |
| STR sysName | 1.3.6.1.2.1.1.5 | DisplayString | read-write | An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name. |
| STR sysLocation | 1.3.6.1.2.1.1.6 | DisplayString | read-write | The physical location of this node (e.g., `telephone closet, 3rd floor'). |
| INT sysServices | 1.3.6.1.2.1.1.7 | INTEGER | read-only | A value which indicates the set of services that this entity primarily offers. The value is a sum. This sum initially takes the value zero, Then, for each layer, L, in the range 1 through 7, that this node performs transactions for, 2 raised to (L - 1) is added to the sum. For example, a node which performs primarily routing functions would have a value of 4 (2^(3-1)). In contrast, a node which is a host offering application services would have a value of 72 (2^(4-1) + 2^(7-1)). Note that in the context of the Internet suite of protocols, values should be calculated accordingly: layer functionality 1 physical (e.g., repeaters) 2 datalink/subnetwork (e.g., bridges) 3 internet (e.g., IP gateways) 4 end-to-end (e.g., IP hosts) 7 applications (e.g., mail relays) For systems including OSI protocols, layers 5 and 6 may also be counted. |
| interfaces | 1.3.6.1.2.1.2 | |||
| INT ifNumber | 1.3.6.1.2.1.2.1 | INTEGER | read-only | The number of network interfaces (regardless of their current state) present on this system. |
| ifTable | 1.3.6.1.2.1.2.2 | not-accessible | A list of interface entries. The number of entries is given by the value of ifNumber. | |
| ifEntry | 1.3.6.1.2.1.2.2.1 | not-accessible | An interface entry containing objects at the subnetwork layer and below for a particular interface. | |
| INT ifIndex | 1.3.6.1.2.1.2.2.1.1 | INTEGER | read-only | A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization. |
| STR ifDescr | 1.3.6.1.2.1.2.2.1.2 | DisplayString | read-only | A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the hardware interface. |
| INT ifType | 1.3.6.1.2.1.2.2.1.3 | INTEGER | read-only | The type of interface, distinguished according to the physical/link protocol(s) immediately `below' the network layer in the protocol stack. |
| INT ifMtu | 1.3.6.1.2.1.2.2.1.4 | INTEGER | read-only | The size of the largest datagram which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface. |
| GAU ifSpeed | 1.3.6.1.2.1.2.2.1.5 | Gauge | read-only | An estimate of the interface's current bandwidth in bits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. |
| PHY ifPhysAddress | 1.3.6.1.2.1.2.2.1.6 | PhysAddress | read-only | The interface's address at the protocol layer immediately `below' the network layer in the protocol stack. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length. |
| INT ifAdminStatus | 1.3.6.1.2.1.2.2.1.7 | INTEGER | read-write | The desired state of the interface. The testing(3) state indicates that no operational packets can be passed. |
| INT ifOperStatus | 1.3.6.1.2.1.2.2.1.8 | INTEGER | read-only | The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed. |
| TIK ifLastChange | 1.3.6.1.2.1.2.2.1.9 | TimeTicks | read-only | The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re- initialization of the local network management subsystem, then this object contains a zero value. |
| CTR ifInOctets | 1.3.6.1.2.1.2.2.1.10 | Counter | read-only | The total number of octets received on the interface, including framing characters. |
| CTR ifInUcastPkts | 1.3.6.1.2.1.2.2.1.11 | Counter | read-only | The number of subnetwork-unicast packets delivered to a higher-layer protocol. |
| CTR ifInNUcastPkts | 1.3.6.1.2.1.2.2.1.12 | Counter | read-only | The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol. |
| CTR ifInDiscards | 1.3.6.1.2.1.2.2.1.13 | Counter | read-only | The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space. |
| CTR ifInErrors | 1.3.6.1.2.1.2.2.1.14 | Counter | read-only | The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. |
| CTR ifInUnknownProtos | 1.3.6.1.2.1.2.2.1.15 | Counter | read-only | The number of packets received via the interface which were discarded because of an unknown or unsupported protocol. |
| CTR ifOutOctets | 1.3.6.1.2.1.2.2.1.16 | Counter | read-only | The total number of octets transmitted out of the interface, including framing characters. |
| CTR ifOutUcastPkts | 1.3.6.1.2.1.2.2.1.17 | Counter | read-only | The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent. |
| CTR ifOutNUcastPkts | 1.3.6.1.2.1.2.2.1.18 | Counter | read-only | The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent. |
| CTR ifOutDiscards | 1.3.6.1.2.1.2.2.1.19 | Counter | read-only | The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. |
| CTR ifOutErrors | 1.3.6.1.2.1.2.2.1.20 | Counter | read-only | The number of outbound packets that could not be transmitted because of errors. |
| GAU ifOutQLen | 1.3.6.1.2.1.2.2.1.21 | Gauge | read-only | The length of the output packet queue (in packets). |
| OID ifSpecific | 1.3.6.1.2.1.2.2.1.22 | OBJECT IDENTIFIER | read-only | A reference to MIB definitions specific to the particular media being used to realize the interface. For example, if the interface is realized by an ethernet, then the value of this object refers to a document defining objects specific to ethernet. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value. |
| at | 1.3.6.1.2.1.3 | |||
| atTable | 1.3.6.1.2.1.3.1 | not-accessible | The Address Translation tables contain the NetworkAddress to `physical' address equivalences. Some interfaces do not use translation tables for determining address equivalences (e.g., DDN-X.25 has an algorithmic method); if all interfaces are of this type, then the Address Translation table is empty, i.e., has zero entries. | |
| atEntry | 1.3.6.1.2.1.3.1.1 | not-accessible | Each entry contains one NetworkAddress to `physical' address equivalence. | |
| INT atIfIndex | 1.3.6.1.2.1.3.1.1.1 | INTEGER | read-write | The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. |
| PHY atPhysAddress | 1.3.6.1.2.1.3.1.1.2 | PhysAddress | read-write | The media-dependent `physical' address. Setting this object to a null string (one of zero length) has the effect of invaliding the corresponding entry in the atTable object. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant atPhysAddress object. |
| IP atNetAddress | 1.3.6.1.2.1.3.1.1.3 | IpAddress | read-write | The NetworkAddress (e.g., the IP address) corresponding to the media-dependent `physical' address. |
| ip | 1.3.6.1.2.1.4 | |||
| INT ipForwarding | 1.3.6.1.2.1.4.1 | INTEGER | read-write | The indication of whether this entity is acting as an IP gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP gateways forward datagrams. IP hosts do not (except those source-routed via the host). Note that for some managed nodes, this object may take on only a subset of the values possible. Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to change this object to an inappropriate value. |
| INT ipDefaultTTL | 1.3.6.1.2.1.4.2 | INTEGER | read-write | The default value inserted into the Time-To-Live field of the IP header of datagrams originated at this entity, whenever a TTL value is not supplied by the transport layer protocol. |
| CTR ipInReceives | 1.3.6.1.2.1.4.3 | Counter | read-only | The total number of input datagrams received from interfaces, including those received in error. |
| CTR ipInHdrErrors | 1.3.6.1.2.1.4.4 | Counter | read-only | The number of input datagrams discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-to-live exceeded, errors discovered in processing their IP options, etc. |
| CTR ipInAddrErrors | 1.3.6.1.2.1.4.5 | Counter | read-only | The number of input datagrams discarded because the IP address in their IP header's destination field was not a valid address to be received at this entity. This count includes invalid addresses (e.g., 0.0.0.0) and addresses of unsupported Classes (e.g., Class E). For entities which are not IP Gateways and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address. |
| CTR ipForwDatagrams | 1.3.6.1.2.1.4.6 | Counter | read-only | The number of input datagrams for which this entity was not their final IP destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities which do not act as IP Gateways, this counter will include only those packets which were Source-Routed via this entity, and the Source- Route option processing was successful. |
| CTR ipInUnknownProtos | 1.3.6.1.2.1.4.7 | Counter | read-only | The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol. |
| CTR ipInDiscards | 1.3.6.1.2.1.4.8 | Counter | read-only | The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly. |
| CTR ipInDelivers | 1.3.6.1.2.1.4.9 | Counter | read-only | The total number of input datagrams successfully delivered to IP user-protocols (including ICMP). |
| CTR ipOutRequests | 1.3.6.1.2.1.4.10 | Counter | read-only | The total number of IP datagrams which local IP user-protocols (including ICMP) supplied to IP in requests for transmission. Note that this counter does not include any datagrams counted in ipForwDatagrams. |
| CTR ipOutDiscards | 1.3.6.1.2.1.4.11 | Counter | read-only | The number of output IP datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (e.g., for lack of buffer space). Note that this counter would include datagrams counted in ipForwDatagrams if any such packets met this (discretionary) discard criterion. |
| CTR ipOutNoRoutes | 1.3.6.1.2.1.4.12 | Counter | read-only | The number of IP datagrams discarded because no route could be found to transmit them to their destination. Note that this counter includes any packets counted in ipForwDatagrams which meet this `no-route' criterion. Note that this includes any datagarms which a host cannot route because all of its default gateways are down. |
| INT ipReasmTimeout | 1.3.6.1.2.1.4.13 | INTEGER | read-only | The maximum number of seconds which received fragments are held while they are awaiting reassembly at this entity. |
| CTR ipReasmReqds | 1.3.6.1.2.1.4.14 | Counter | read-only | The number of IP fragments received which needed to be reassembled at this entity. |
| CTR ipReasmOKs | 1.3.6.1.2.1.4.15 | Counter | read-only | The number of IP datagrams successfully re- assembled. |
| CTR ipReasmFails | 1.3.6.1.2.1.4.16 | Counter | read-only | The number of failures detected by the IP re- assembly algorithm (for whatever reason: timed out, errors, etc). Note that this is not necessarily a count of discarded IP fragments since some algorithms (notably the algorithm in RFC 815) can lose track of the number of fragments by combining them as they are received. |
| CTR ipFragOKs | 1.3.6.1.2.1.4.17 | Counter | read-only | The number of IP datagrams that have been successfully fragmented at this entity. |
| CTR ipFragFails | 1.3.6.1.2.1.4.18 | Counter | read-only | The number of IP datagrams that have been discarded because they needed to be fragmented at this entity but could not be, e.g., because their Don't Fragment flag was set. |
| CTR ipFragCreates | 1.3.6.1.2.1.4.19 | Counter | read-only | The number of IP datagram fragments that have been generated as a result of fragmentation at this entity. |
| ipAddrTable | 1.3.6.1.2.1.4.20 | not-accessible | The table of addressing information relevant to this entity's IP addresses. | |
| ipAddrEntry | 1.3.6.1.2.1.4.20.1 | not-accessible | The addressing information for one of this entity's IP addresses. | |
| IP ipAdEntAddr | 1.3.6.1.2.1.4.20.1.1 | IpAddress | read-only | The IP address to which this entry's addressing information pertains. |
| INT ipAdEntIfIndex | 1.3.6.1.2.1.4.20.1.2 | INTEGER | read-only | The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. |
| IP ipAdEntNetMask | 1.3.6.1.2.1.4.20.1.3 | IpAddress | read-only | The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0. |
| INT ipAdEntBcastAddr | 1.3.6.1.2.1.4.20.1.4 | INTEGER | read-only | The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface. |
| INT ipAdEntReasmMaxSize | 1.3.6.1.2.1.4.20.1.5 | INTEGER | read-only | The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface. |
| ipRouteTable | 1.3.6.1.2.1.4.21 | not-accessible | This entity's IP Routing table. | |
| ipRouteEntry | 1.3.6.1.2.1.4.21.1 | not-accessible | A route to a particular destination. | |
| IP ipRouteDest | 1.3.6.1.2.1.4.21.1.1 | IpAddress | read-write | The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use. |
| INT ipRouteIfIndex | 1.3.6.1.2.1.4.21.1.2 | INTEGER | read-write | The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. |
| INT ipRouteMetric1 | 1.3.6.1.2.1.4.21.1.3 | INTEGER | read-write | The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1. |
| INT ipRouteMetric2 | 1.3.6.1.2.1.4.21.1.4 | INTEGER | read-write | An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1. |
| INT ipRouteMetric3 | 1.3.6.1.2.1.4.21.1.5 | INTEGER | read-write | An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1. |
| INT ipRouteMetric4 | 1.3.6.1.2.1.4.21.1.6 | INTEGER | read-write | An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1. |
| IP ipRouteNextHop | 1.3.6.1.2.1.4.21.1.7 | IpAddress | read-write | The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface.) |
| INT ipRouteType | 1.3.6.1.2.1.4.21.1.8 | INTEGER | read-write | The type of route. Note that the values direct(3) and indirect(4) refer to the notion of direct and indirect routing in the IP architecture. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipRouteType object. |
| INT ipRouteProto | 1.3.6.1.2.1.4.21.1.9 | INTEGER | read-only | The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols. |
| INT ipRouteAge | 1.3.6.1.2.1.4.21.1.10 | INTEGER | read-write | The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned. |
| IP ipRouteMask | 1.3.6.1.2.1.4.21.1.11 | IpAddress | read-write | Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the ipRouteMask by determining whether the value of the correspondent ipRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the ipRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism. |
| INT ipRouteMetric5 | 1.3.6.1.2.1.4.21.1.12 | INTEGER | read-write | An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1. |
| OID ipRouteInfo | 1.3.6.1.2.1.4.21.1.13 | OBJECT IDENTIFIER | read-only | A reference to MIB definitions specific to the particular routing protocol which is responsible for this route, as determined by the value specified in the route's ipRouteProto value. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value. |
| ipNetToMediaTable | 1.3.6.1.2.1.4.22 | not-accessible | The IP Address Translation table used for mapping from IP addresses to physical addresses. | |
| ipNetToMediaEntry | 1.3.6.1.2.1.4.22.1 | not-accessible | Each entry contains one IpAddress to `physical' address equivalence. | |
| INT ipNetToMediaIfIndex | 1.3.6.1.2.1.4.22.1.1 | INTEGER | read-write | The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. |
| PHY ipNetToMediaPhysAddress | 1.3.6.1.2.1.4.22.1.2 | PhysAddress | read-write | The media-dependent `physical' address. |
| IP ipNetToMediaNetAddress | 1.3.6.1.2.1.4.22.1.3 | IpAddress | read-write | The IpAddress corresponding to the media- dependent `physical' address. |
| INT ipNetToMediaType | 1.3.6.1.2.1.4.22.1.4 | INTEGER | read-write | The type of mapping. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipNetToMediaTable. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipNetToMediaType object. |
| CTR ipRoutingDiscards | 1.3.6.1.2.1.4.23 | Counter | read-only | The number of routing entries which were chosen to be discarded even though they are valid. One possible reason for discarding such an entry could be to free-up buffer space for other routing entries. |
| icmp | 1.3.6.1.2.1.5 | |||
| CTR icmpInMsgs | 1.3.6.1.2.1.5.1 | Counter | read-only | The total number of ICMP messages which the entity received. Note that this counter includes all those counted by icmpInErrors. |
| CTR icmpInErrors | 1.3.6.1.2.1.5.2 | Counter | read-only | The number of ICMP messages which the entity received but determined as having ICMP-specific errors (bad ICMP checksums, bad length, etc.). |
| CTR icmpInDestUnreachs | 1.3.6.1.2.1.5.3 | Counter | read-only | The number of ICMP Destination Unreachable messages received. |
| CTR icmpInTimeExcds | 1.3.6.1.2.1.5.4 | Counter | read-only | The number of ICMP Time Exceeded messages received. |
| CTR icmpInParmProbs | 1.3.6.1.2.1.5.5 | Counter | read-only | The number of ICMP Parameter Problem messages received. |
| CTR icmpInSrcQuenchs | 1.3.6.1.2.1.5.6 | Counter | read-only | The number of ICMP Source Quench messages received. |
| CTR icmpInRedirects | 1.3.6.1.2.1.5.7 | Counter | read-only | The number of ICMP Redirect messages received. |
| CTR icmpInEchos | 1.3.6.1.2.1.5.8 | Counter | read-only | The number of ICMP Echo (request) messages received. |
| CTR icmpInEchoReps | 1.3.6.1.2.1.5.9 | Counter | read-only | The number of ICMP Echo Reply messages received. |
| CTR icmpInTimestamps | 1.3.6.1.2.1.5.10 | Counter | read-only | The number of ICMP Timestamp (request) messages received. |
| CTR icmpInTimestampReps | 1.3.6.1.2.1.5.11 | Counter | read-only | The number of ICMP Timestamp Reply messages received. |
| CTR icmpInAddrMasks | 1.3.6.1.2.1.5.12 | Counter | read-only | The number of ICMP Address Mask Request messages received. |
| CTR icmpInAddrMaskReps | 1.3.6.1.2.1.5.13 | Counter | read-only | The number of ICMP Address Mask Reply messages received. |
| CTR icmpOutMsgs | 1.3.6.1.2.1.5.14 | Counter | read-only | The total number of ICMP messages which this entity attempted to send. Note that this counter includes all those counted by icmpOutErrors. |
| CTR icmpOutErrors | 1.3.6.1.2.1.5.15 | Counter | read-only | The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include errors discovered outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there may be no types of error which contribute to this counter's value. |
| CTR icmpOutDestUnreachs | 1.3.6.1.2.1.5.16 | Counter | read-only | The number of ICMP Destination Unreachable messages sent. |
| CTR icmpOutTimeExcds | 1.3.6.1.2.1.5.17 | Counter | read-only | The number of ICMP Time Exceeded messages sent. |
| CTR icmpOutParmProbs | 1.3.6.1.2.1.5.18 | Counter | read-only | The number of ICMP Parameter Problem messages sent. |
| CTR icmpOutSrcQuenchs | 1.3.6.1.2.1.5.19 | Counter | read-only | The number of ICMP Source Quench messages sent. |
| CTR icmpOutRedirects | 1.3.6.1.2.1.5.20 | Counter | read-only | The number of ICMP Redirect messages sent. For a host, this object will always be zero, since hosts do not send redirects. |
| CTR icmpOutEchos | 1.3.6.1.2.1.5.21 | Counter | read-only | The number of ICMP Echo (request) messages sent. |
| CTR icmpOutEchoReps | 1.3.6.1.2.1.5.22 | Counter | read-only | The number of ICMP Echo Reply messages sent. |
| CTR icmpOutTimestamps | 1.3.6.1.2.1.5.23 | Counter | read-only | The number of ICMP Timestamp (request) messages sent. |
| CTR icmpOutTimestampReps | 1.3.6.1.2.1.5.24 | Counter | read-only | The number of ICMP Timestamp Reply messages sent. |
| CTR icmpOutAddrMasks | 1.3.6.1.2.1.5.25 | Counter | read-only | The number of ICMP Address Mask Request messages sent. |
| CTR icmpOutAddrMaskReps | 1.3.6.1.2.1.5.26 | Counter | read-only | The number of ICMP Address Mask Reply messages sent. |
| tcp | 1.3.6.1.2.1.6 | |||
| INT tcpRtoAlgorithm | 1.3.6.1.2.1.6.1 | INTEGER | read-only | The algorithm used to determine the timeout value used for retransmitting unacknowledged octets. |
| INT tcpRtoMin | 1.3.6.1.2.1.6.2 | INTEGER | read-only | The minimum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. In particular, when the timeout algorithm is rsre(3), an object of this type has the semantics of the LBOUND quantity described in RFC 793. |
| INT tcpRtoMax | 1.3.6.1.2.1.6.3 | INTEGER | read-only | The maximum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. In particular, when the timeout algorithm is rsre(3), an object of this type has the semantics of the UBOUND quantity described in RFC 793. |
| INT tcpMaxConn | 1.3.6.1.2.1.6.4 | INTEGER | read-only | The limit on the total number of TCP connections the entity can support. In entities where the maximum number of connections is dynamic, this object should contain the value -1. |
| CTR tcpActiveOpens | 1.3.6.1.2.1.6.5 | Counter | read-only | The number of times TCP connections have made a direct transition to the SYN-SENT state from the CLOSED state. |
| CTR tcpPassiveOpens | 1.3.6.1.2.1.6.6 | Counter | read-only | The number of times TCP connections have made a direct transition to the SYN-RCVD state from the LISTEN state. |
| CTR tcpAttemptFails | 1.3.6.1.2.1.6.7 | Counter | read-only | The number of times TCP connections have made a direct transition to the CLOSED state from either the SYN-SENT state or the SYN-RCVD state, plus the number of times TCP connections have made a direct transition to the LISTEN state from the SYN-RCVD state. |
| CTR tcpEstabResets | 1.3.6.1.2.1.6.8 | Counter | read-only | The number of times TCP connections have made a direct transition to the CLOSED state from either the ESTABLISHED state or the CLOSE-WAIT state. |
| GAU tcpCurrEstab | 1.3.6.1.2.1.6.9 | Gauge | read-only | The number of TCP connections for which the current state is either ESTABLISHED or CLOSE- WAIT. |
| CTR tcpInSegs | 1.3.6.1.2.1.6.10 | Counter | read-only | The total number of segments received, including those received in error. This count includes segments received on currently established connections. |
| CTR tcpOutSegs | 1.3.6.1.2.1.6.11 | Counter | read-only | The total number of segments sent, including those on current connections but excluding those containing only retransmitted octets. |
| CTR tcpRetransSegs | 1.3.6.1.2.1.6.12 | Counter | read-only | The total number of segments retransmitted - that is, the number of TCP segments transmitted containing one or more previously transmitted octets. |
| tcpConnTable | 1.3.6.1.2.1.6.13 | not-accessible | A table containing TCP connection-specific information. | |
| tcpConnEntry | 1.3.6.1.2.1.6.13.1 | not-accessible | Information about a particular current TCP connection. An object of this type is transient, in that it ceases to exist when (or soon after) the connection makes the transition to the CLOSED state. | |
| INT tcpConnState | 1.3.6.1.2.1.6.13.1.1 | INTEGER | read-write | The state of this TCP connection. The only value which may be set by a management station is deleteTCB(12). Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to set this object to any other value. If a management station sets this object to the value deleteTCB(12), then this has the effect of deleting the TCB (as defined in RFC 793) of the corresponding connection on the managed node, resulting in immediate termination of the connection. As an implementation-specific option, a RST segment may be sent from the managed node to the other TCP endpoint (note however that RST segments are not sent reliably). |
| IP tcpConnLocalAddress | 1.3.6.1.2.1.6.13.1.2 | IpAddress | read-only | The local IP address for this TCP connection. In the case of a connection in the listen state which is willing to accept connections for any IP interface associated with the node, the value 0.0.0.0 is used. |
| INT tcpConnLocalPort | 1.3.6.1.2.1.6.13.1.3 | INTEGER | read-only | The local port number for this TCP connection. |
| IP tcpConnRemAddress | 1.3.6.1.2.1.6.13.1.4 | IpAddress | read-only | The remote IP address for this TCP connection. |
| INT tcpConnRemPort | 1.3.6.1.2.1.6.13.1.5 | INTEGER | read-only | The remote port number for this TCP connection. |
| CTR tcpInErrs | 1.3.6.1.2.1.6.14 | Counter | read-only | The total number of segments received in error (e.g., bad TCP checksums). |
| CTR tcpOutRsts | 1.3.6.1.2.1.6.15 | Counter | read-only | The number of TCP segments sent containing the RST flag. |
| udp | 1.3.6.1.2.1.7 | |||
| CTR udpInDatagrams | 1.3.6.1.2.1.7.1 | Counter | read-only | The total number of UDP datagrams delivered to UDP users. |
| CTR udpNoPorts | 1.3.6.1.2.1.7.2 | Counter | read-only | The total number of received UDP datagrams for which there was no application at the destination port. |
| CTR udpInErrors | 1.3.6.1.2.1.7.3 | Counter | read-only | The number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port. |
| CTR udpOutDatagrams | 1.3.6.1.2.1.7.4 | Counter | read-only | The total number of UDP datagrams sent from this entity. |
| udpTable | 1.3.6.1.2.1.7.5 | not-accessible | A table containing UDP listener information. | |
| udpEntry | 1.3.6.1.2.1.7.5.1 | not-accessible | Information about a particular current UDP listener. | |
| IP udpLocalAddress | 1.3.6.1.2.1.7.5.1.1 | IpAddress | read-only | The local IP address for this UDP listener. In the case of a UDP listener which is willing to accept datagrams for any IP interface associated with the node, the value 0.0.0.0 is used. |
| INT udpLocalPort | 1.3.6.1.2.1.7.5.1.2 | INTEGER | read-only | The local port number for this UDP listener. |
| egp | 1.3.6.1.2.1.8 | |||
| transmission | 1.3.6.1.2.1.10 | |||
| snmp | 1.3.6.1.2.1.11 | |||
| CTR snmpInPkts | 1.3.6.1.2.1.11.1 | Counter | read-only | The total number of Messages delivered to the SNMP entity from the transport service. |
| CTR snmpOutPkts | 1.3.6.1.2.1.11.2 | Counter | read-only | The total number of SNMP Messages which were passed from the SNMP protocol entity to the transport service. |
| CTR snmpInBadVersions | 1.3.6.1.2.1.11.3 | Counter | read-only | The total number of SNMP Messages which were delivered to the SNMP protocol entity and were for an unsupported SNMP version. |
| CTR snmpInBadCommunityNames | 1.3.6.1.2.1.11.4 | Counter | read-only | The total number of SNMP Messages delivered to the SNMP protocol entity which used a SNMP community name not known to said entity. |
| CTR snmpInBadCommunityUses | 1.3.6.1.2.1.11.5 | Counter | read-only | The total number of SNMP Messages delivered to the SNMP protocol entity which represented an SNMP operation which was not allowed by the SNMP community named in the Message. |
| CTR snmpInASNParseErrs | 1.3.6.1.2.1.11.6 | Counter | read-only | The total number of ASN.1 or BER errors encountered by the SNMP protocol entity when decoding received SNMP Messages. |
| CTR snmpInTooBigs | 1.3.6.1.2.1.11.8 | Counter | read-only | The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `tooBig'. |
| CTR snmpInNoSuchNames | 1.3.6.1.2.1.11.9 | Counter | read-only | The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `noSuchName'. |
| CTR snmpInBadValues | 1.3.6.1.2.1.11.10 | Counter | read-only | The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `badValue'. |
| CTR snmpInReadOnlys | 1.3.6.1.2.1.11.11 | Counter | read-only | The total number valid SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `readOnly'. It should be noted that it is a protocol error to generate an SNMP PDU which contains the value `readOnly' in the error-status field, as such this object is provided as a means of detecting incorrect implementations of the SNMP. |
| CTR snmpInGenErrs | 1.3.6.1.2.1.11.12 | Counter | read-only | The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `genErr'. |
| CTR snmpInTotalReqVars | 1.3.6.1.2.1.11.13 | Counter | read-only | The total number of MIB objects which have been retrieved successfully by the SNMP protocol entity as the result of receiving valid SNMP Get-Request and Get-Next PDUs. |
| CTR snmpInTotalSetVars | 1.3.6.1.2.1.11.14 | Counter | read-only | The total number of MIB objects which have been altered successfully by the SNMP protocol entity as the result of receiving valid SNMP Set-Request PDUs. |
| CTR snmpInGetRequests | 1.3.6.1.2.1.11.15 | Counter | read-only | The total number of SNMP Get-Request PDUs which have been accepted and processed by the SNMP protocol entity. |
| CTR snmpInGetNexts | 1.3.6.1.2.1.11.16 | Counter | read-only | The total number of SNMP Get-Next PDUs which have been accepted and processed by the SNMP protocol entity. |
| CTR snmpInSetRequests | 1.3.6.1.2.1.11.17 | Counter | read-only | The total number of SNMP Set-Request PDUs which have been accepted and processed by the SNMP protocol entity. |
| CTR snmpInGetResponses | 1.3.6.1.2.1.11.18 | Counter | read-only | The total number of SNMP Get-Response PDUs which have been accepted and processed by the SNMP protocol entity. |
| CTR snmpInTraps | 1.3.6.1.2.1.11.19 | Counter | read-only | The total number of SNMP Trap PDUs which have been accepted and processed by the SNMP protocol entity. |
| CTR snmpOutTooBigs | 1.3.6.1.2.1.11.20 | Counter | read-only | The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `tooBig.' |
| CTR snmpOutNoSuchNames | 1.3.6.1.2.1.11.21 | Counter | read-only | The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status is `noSuchName'. |
| CTR snmpOutBadValues | 1.3.6.1.2.1.11.22 | Counter | read-only | The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `badValue'. |
| CTR snmpOutGenErrs | 1.3.6.1.2.1.11.24 | Counter | read-only | The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `genErr'. |
| CTR snmpOutGetRequests | 1.3.6.1.2.1.11.25 | Counter | read-only | The total number of SNMP Get-Request PDUs which have been generated by the SNMP protocol entity. |
| CTR snmpOutGetNexts | 1.3.6.1.2.1.11.26 | Counter | read-only | The total number of SNMP Get-Next PDUs which have been generated by the SNMP protocol entity. |
| CTR snmpOutSetRequests | 1.3.6.1.2.1.11.27 | Counter | read-only | The total number of SNMP Set-Request PDUs which have been generated by the SNMP protocol entity. |
| CTR snmpOutGetResponses | 1.3.6.1.2.1.11.28 | Counter | read-only | The total number of SNMP Get-Response PDUs which have been generated by the SNMP protocol entity. |
| CTR snmpOutTraps | 1.3.6.1.2.1.11.29 | Counter | read-only | The total number of SNMP Trap PDUs which have been generated by the SNMP protocol entity. |
| INT snmpEnableAuthenTraps | 1.3.6.1.2.1.11.30 | INTEGER | read-write | Indicates whether the SNMP agent process is permitted to generate authentication-failure traps. The value of this object overrides any configuration information; as such, it provides a means whereby all authentication-failure traps may be disabled. Note that it is strongly recommended that this object be stored in non-volatile memory so that it remains constant between re-initializations of the network management system. |
| char | 1.3.6.1.3.19 | |||
| INT charNumber | 1.3.6.1.3.19.1 | INTEGER | read-only | The number of entries in charPortTable, regardless of their current state. |
| charPortTable | 1.3.6.1.3.19.2 | not-accessible | A list of port entries. The number of entries is given by the value of charNumber. | |
| charPortEntry | 1.3.6.1.3.19.2.1 | not-accessible | Status and parameter values for a character port. | |
| INT charPortIndex | 1.3.6.1.3.19.2.1.1 | INTEGER | read-only | A unique value for each character port. Its value ranges between 1 and the value of charNumber. By convention and if possible, hardware port numbers come first, with a simple, direct mapping. The value for each port must remain constant at least from one re-initialization of the network management agent to the next. |
| STR charPortName | 1.3.6.1.3.19.2.1.2 | DisplayString | read-write | An administratively assigned name for the port, typically with some local significance. |
| INT charPortType | 1.3.6.1.3.19.2.1.3 | INTEGER | read-only | The port's type, 'physical' if the port represents an external hardware connector, 'virtual' if it does not. |
| OID charPortHardware | 1.3.6.1.3.19.2.1.4 | AutonomousType | read-only | A reference to hardware MIB definitions specific to a physical port's external connector. For example, if the connector is RS-232, then the value of this object refers to a document defining objects specific to RS-232. If an agent is not configured to have such values, the agent returns the object identifier: nullHardware OBJECT IDENTIFIER ::= { 0 0 } |
| INT charPortReset | 1.3.6.1.3.19.2.1.5 | INTEGER | read-write | A control to force the port into a clean, initial state, both hardware and software, disconnecting all the port's existing sessions. In response to a get-request or get-next-request, the agent always returns 'ready' as the value. Setting the value to 'execute' causes a reset. |
| INT charPortAdminStatus | 1.3.6.1.3.19.2.1.6 | INTEGER | read-write | The port's desired state, independent of flow control. 'enabled' indicates that the port is allowed to pass characters and form new sessions. 'disabled' indicates that the port is allowed to pass characters but not form new sessions. 'off' indicates that the port is not allowed to pass characters or have any sessions. 'maintenance' indicates a maintenance mode, exclusive of normal operation, such as running a test. |
| INT charPortOperStatus | 1.3.6.1.3.19.2.1.7 | INTEGER | read-only | The port's actual, operational state, independent of flow control. 'up' indicates able to function normally. 'down' indicates inability to function for administrative or operational reasons. 'maintenance' indicates a maintenance mode, exclusive of normal operation, such as running a test. 'absent' indicates that port hardware is not present. 'active' indicates up with a user present (e.g. logged in). |
| TIK charPortLastChange | 1.3.6.1.3.19.2.1.8 | TimeTicks | read-only | The value of sysUpTime at the time the port entered its current operational state. If the current state was entered prior to the last reinitialization of the local network management subsystem, then this object contains a zero value. |
| INT charPortInFlowType | 1.3.6.1.3.19.2.1.9 | INTEGER | read-write | The port's type of input flow control. 'none' indicates no flow control at this level or below. 'xonXoff' indicates software flow control by recognizing XON and XOFF characters. 'hardware' indicates flow control delegated to the lower level, for example a parallel port. 'ctsRts' and 'dsrDtr' are specific to RS-232-like ports. Although not architecturally pure, they are included here for simplicity's sake. |
| INT charPortOutFlowType | 1.3.6.1.3.19.2.1.10 | INTEGER | read-write | The port's type of output flow control. 'none' indicates no flow control at this level or below. 'xonXoff' indicates software flow control by recognizing XON and XOFF characters. 'hardware' indicates flow control delegated to the lower level, for example a parallel port. 'ctsRts' and 'dsrDtr' are specific to RS-232-like ports. Although not architecturally pure, they are included here for simplicy's sake. |
| INT charPortInFlowState | 1.3.6.1.3.19.2.1.11 | INTEGER | read-only | The current operational state of input flow control on the port. 'none' indicates not applicable. 'unknown' indicates this level does not know. 'stop' indicates flow not allowed. 'go' indicates flow allowed. |
| INT charPortOutFlowState | 1.3.6.1.3.19.2.1.12 | INTEGER | read-only | The current operational state of output flow control on the port. 'none' indicates not applicable. 'unknown' indicates this level does not know. 'stop' indicates flow not allowed. 'go' indicates flow allowed. |
| CTR charPortInCharacters | 1.3.6.1.3.19.2.1.13 | Counter | read-only | Total number of characters detected as input from the port since system re-initialization and while the port operational state was 'up', 'active', or 'maintenance', including, for example, framing, flow control (i.e. XON and XOFF), each occurrence of a BREAK condition, locally-processed input, and input sent to all sessions. |
| CTR charPortOutCharacters | 1.3.6.1.3.19.2.1.14 | Counter | read-only | Total number of characters detected as output to the port since system re-initialization and while the port operational state was 'up', 'active', or 'maintenance', including, for example, framing, flow control (i.e. XON and XOFF), each occurrence of a BREAK condition, locally-created output, and output received from all sessions. |
| INT charPortAdminOrigin | 1.3.6.1.3.19.2.1.15 | INTEGER | read-write | The administratively allowed origin for establishing session on the port. 'dynamic' allows 'network' or 'local' session establishment. 'none' disallows session establishment. |
| INT charPortSessionMaximum | 1.3.6.1.3.19.2.1.16 | INTEGER | read-write | The maximum number of concurrent sessions allowed on the port. A value of -1 indicates no maximum. Setting the maximum to less than the current number of sessions has unspecified results. |
| GAU charPortSessionNumber | 1.3.6.1.3.19.2.1.17 | Gauge | read-only | The number of open sessions on the port that are in the connecting, connected, or disconnecting state. |
| INT charPortSessionIndex | 1.3.6.1.3.19.2.1.18 | INTEGER | read-only | The value of charSessIndex for the port's first or only active session. If the port has no active session, the agent returns the value zero. |
| charSessTable | 1.3.6.1.3.19.3 | not-accessible | A list of port session entries. | |
| charSessEntry | 1.3.6.1.3.19.3.1 | not-accessible | Status and parameter values for a character port session. | |
| INT charSessPortIndex | 1.3.6.1.3.19.3.1.1 | INTEGER | read-only | The value of charPortIndex for the port to which this session belongs. |
| INT charSessIndex | 1.3.6.1.3.19.3.1.2 | INTEGER | read-only | The session index in the context of the port, a non-zero positive integer. Session indexes within a port need not be sequential. Session indexes may be reused for different ports. For example, port 1 and port 3 may both have a session 2 at the same time. Session indexes may have any valid integer value, with any meaning convenient to the agent implementation. |
| INT charSessKill | 1.3.6.1.3.19.3.1.3 | INTEGER | read-write | A control to terminate the session. In response to a get-request or get-next-request, the agent always returns 'ready' as the value. Setting the value to 'execute' causes termination. |
| INT charSessState | 1.3.6.1.3.19.3.1.4 | INTEGER | read-only | The current operational state of the session, disregarding flow control. 'connected' indicates that character data could flow on the network side of session. 'connecting' indicates moving from nonexistent toward 'connected'. 'disconnecting' indicates moving from 'connected' or 'connecting' to nonexistent. |
| OID charSessProtocol | 1.3.6.1.3.19.3.1.5 | AutonomousType | read-only | The network protocol over which the session is running. Other OBJECT IDENTIFIER values may be defined elsewhere, in association with specific protocols. However, this document assigns those of known interest as of this writing. |
| INT charSessOperOrigin | 1.3.6.1.3.19.3.1.6 | INTEGER | read-only | The session's source of establishment. |
| CTR charSessInCharacters | 1.3.6.1.3.19.3.1.7 | Counter | read-only | This session's subset of charPortInCharacters. |
| CTR charSessOutCharacters | 1.3.6.1.3.19.3.1.8 | Counter | read-only | This session's subset of charPortOutCharacters. |
| NUM charSessConnectionId | 1.3.6.1.3.19.3.1.9 | InstancePointer | read-only | A reference to additional local MIB information. This should be the highest available related MIB, corresponding to charSessProtocol, such as Telnet. For example, the value for a TCP connection (in the absence of a Telnet MIB) is the object identifier of tcpConnState. If an agent is not configured to have such values, the agent returns the object identifier: nullConnectionId OBJECT IDENTIFIER ::= { 0 0 } |
| TIK charSessStartTime | 1.3.6.1.3.19.3.1.10 | TimeTicks | read-only | The value of sysUpTime [3] when the session entered connecting state. |
| wellKnownProtocols | 1.3.6.1.3.19.4 | |||
| protocolOther | 1.3.6.1.3.19.4.1 | |||
| protocolTelnet | 1.3.6.1.3.19.4.2 | |||
| protocolRlogin | 1.3.6.1.3.19.4.3 | |||
| protocolLat | 1.3.6.1.3.19.4.4 | |||
| protocolX29 | 1.3.6.1.3.19.4.5 | |||
| protocolVtp | 1.3.6.1.3.19.4.6 | |||
| rs232 | 1.3.6.1.3.20 | |||
| INT rs232Number | 1.3.6.1.3.20.1 | INTEGER | read-only | The number of ports (regardless of their current state) in the RS-232-like general port table. |
| rs232PortTable | 1.3.6.1.3.20.2 | not-accessible | A list of port entries. The number of entries is given by the value of rs232Number. | |
| rs232PortEntry | 1.3.6.1.3.20.2.1 | not-accessible | Status and parameter values for a port. | |
| INT rs232PortIndex | 1.3.6.1.3.20.2.1.1 | INTEGER | read-only | A unique value for each port. Its value ranges between 1 and the value of rs232Number. By convention and if possible, hardware port numbers map directly to external connectors. The value for each port must remain constant at least from one re-initialization of the network management agent to the next. |
| INT rs232PortType | 1.3.6.1.3.20.2.1.2 | INTEGER | read-only | The port's hardware type. |
| INT rs232PortInSigNumber | 1.3.6.1.3.20.2.1.3 | INTEGER | read-only | The number of input signals for the port in the input signal table (rs232PortInSigTable). The table contains entries only for those signals the software can detect. |
| INT rs232PortOutSigNumber | 1.3.6.1.3.20.2.1.4 | INTEGER | read-only | The number of output signals for the port in the output signal table (rs232PortOutSigTable). The table contains entries only for those signals the software can assert. |
| INT rs232PortInSpeed | 1.3.6.1.3.20.2.1.5 | INTEGER | read-write | The port's input speed in bits per second. |
| INT rs232PortOutSpeed | 1.3.6.1.3.20.2.1.6 | INTEGER | read-write | The port's output speed in bits per second. |
| rs232AsyncPortTable | 1.3.6.1.3.20.3 | not-accessible | A list of asynchronous port entries. The maximum entry number is given by the value of rs232Number. Entries need not exist for synchronous ports. | |
| rs232AsyncPortEntry | 1.3.6.1.3.20.3.1 | not-accessible | Status and parameter values for an asynchronous port. | |
| INT rs232AsyncPortIndex | 1.3.6.1.3.20.3.1.1 | INTEGER | read-only | A unique value for each port. Its value is the same as rs232PortIndex for the port. |
| INT rs232AsyncPortBits | 1.3.6.1.3.20.3.1.2 | INTEGER | read-write | The port's number of bits in a character. |
| INT rs232AsyncPortStopBits | 1.3.6.1.3.20.3.1.3 | INTEGER | read-write | The port's number of stop bits. |
| INT rs232AsyncPortParity | 1.3.6.1.3.20.3.1.4 | INTEGER | read-write | The port's sense of a character parity bit. |
| INT rs232AsyncPortAutobaud | 1.3.6.1.3.20.3.1.5 | INTEGER | read-write | A control for the port's ability to automatically sense input speed. When rs232PortAutoBaud is 'enabled', a port may autobaud to values different from the set values for speed, parity, and character size. As a result a network management system may temporarily observe values different from what was previously set. |
| CTR rs232AsyncPortParityErrs | 1.3.6.1.3.20.3.1.6 | Counter | read-only | Total number of characters with a parity error, input from the port since system re-initialization and while the port state was 'up' or 'test'. |
| CTR rs232AsyncPortFramingErrs | 1.3.6.1.3.20.3.1.7 | Counter | read-only | Total number of characters with a framing error, input from the port since system re-initialization and while the port state was 'up' or 'test'. |
| CTR rs232AsyncPortOverrunErrs | 1.3.6.1.3.20.3.1.8 | Counter | read-only | Total number of characters with an overrun error, input from the port since system re-initialization and while the port state was 'up' or 'test'. |
| rs232SyncPortTable | 1.3.6.1.3.20.4 | not-accessible | A list of synchronous port entries. The maximum entry number is given by the value of rs232Number. Entries need not exist for asynchronous ports. | |
| rs232SyncPortEntry | 1.3.6.1.3.20.4.1 | not-accessible | Status and parameter values for a synchronous port. | |
| INT rs232SyncPortIndex | 1.3.6.1.3.20.4.1.1 | INTEGER | read-only | A unique value for each port. Its value is the same as rs232PortIndex for the port. |
| INT rs232SyncPortClockSource | 1.3.6.1.3.20.4.1.2 | INTEGER | read-write | Source of the port's bit rate clock. 'split' means the tranmit clock is internal and the receive clock is external. |
| CTR rs232SyncPortFrameCheckErrs | 1.3.6.1.3.20.4.1.3 | Counter | read-only | Total number of frames with an invalid frame check sequence, input from the port since system re-initialization and while the port state was 'up' or 'test'. |
| CTR rs232SyncPortTransmitUnderrunErrs | 1.3.6.1.3.20.4.1.4 | Counter | read-only | Total number of frames that failed to be transmitted on the port since system re-initialization and while the port state was 'up' or 'test' because data was not available to the transmitter in time. |
| CTR rs232SyncPortReceiveOverrunErrs | 1.3.6.1.3.20.4.1.5 | Counter | read-only | Total number of frames that failed to be received on the port since system re-initialization and while the port state was 'up' or 'test' because the receiver did not accept the data in time. |
| CTR rs232SyncPortInterruptedFrames | 1.3.6.1.3.20.4.1.6 | Counter | read-only | Total number of frames that failed to be received or transmitted on the port due to loss of modem signals since system re-initialization and while the port state was 'up' or 'test'. |
| CTR rs232SyncPortAbortedFrames | 1.3.6.1.3.20.4.1.7 | Counter | read-only | Number of frames aborted on the port due to receiving an abort sequence since system re-initialization and while the port state was 'up' or 'test'. |
| rs232InSigTable | 1.3.6.1.3.20.5 | not-accessible | A list of port input control signal entries. | |
| rs232InSigEntry | 1.3.6.1.3.20.5.1 | not-accessible | Input control signal status for a hardware port. | |
| INT rs232InSigPortIndex | 1.3.6.1.3.20.5.1.1 | INTEGER | read-only | The value of rs232PortIndex for the port to which this entry belongs. |
| INT rs232InSigName | 1.3.6.1.3.20.5.1.2 | INTEGER | read-only | Identification of a hardware signal, as follows: rts Request to Send cts Clear to Send dsr Data Set Ready dtr Data Terminal Ready ri Ring Indicator dcd Received Line Signal Detector sq Signal Quality Detector srs Data Signaling Rate Selector srts Secondary Request to Send scts Secondary Clear to Send sdcd Secondary Received Line Signal Detector |
| INT rs232InSigState | 1.3.6.1.3.20.5.1.3 | INTEGER | read-only | The current signal state. |
| CTR rs232InSigChanges | 1.3.6.1.3.20.5.1.4 | Counter | read-only | The number of times the signal has changed from 'on' to 'off' or from 'off' to 'on'. |
| rs232OutSigTable | 1.3.6.1.3.20.6 | not-accessible | A list of port output control signal entries. | |
| rs232OutSigEntry | 1.3.6.1.3.20.6.1 | not-accessible | Output control signal status for a hardware port. | |
| INT rs232OutSigPortIndex | 1.3.6.1.3.20.6.1.1 | INTEGER | read-only | The value of rs232PortIndex for the port to which this entry belongs. |
| INT rs232OutSigName | 1.3.6.1.3.20.6.1.2 | INTEGER | read-only | Identification of a hardware signal, as follows: rts Request to Send cts Clear to Send dsr Data Set Ready dtr Data Terminal Ready ri Ring Indicator dcd Received Line Signal Detector sq Signal Quality Detector srs Data Signaling Rate Selector srts Secondary Request to Send scts Secondary Clear to Send sdcd Secondary Received Line Signal Detector |
| INT rs232OutSigState | 1.3.6.1.3.20.6.1.3 | INTEGER | read-only | The current signal state. |
| CTR rs232OutSigChanges | 1.3.6.1.3.20.6.1.4 | Counter | read-only | The number of times the signal has changed from 'on' to 'off' or from 'off' to 'on'. |
| xyplex | 1.3.6.1.4.1.33 | |||
| xSystem | 1.3.6.1.4.1.33.1 | |||
| NTF resourceLack | 1.3.6.1.4.1.33.1.0.1 | Indication that the system incremented the corresponding value of resLacks. | ||
| STR sysIdent | 1.3.6.1.4.1.33.1.1 | DisplayString | read-write | An identification string for local and remote displays. Corresponds directly to SERVER IDENTIFICATION and the value labeled 'Identification:' on the SERVER CHARACTERISTICS display. |
| INT sysDefineMode | 1.3.6.1.4.1.33.1.2 | INTEGER | read-write | The system's operation with regard to DEFINE commands. 'permOnly' indicates that DEFINE commands modify only the permanent data base. 'operAndPerm' indicates that DEFINE commands modify both operational and permanent data bases, unless specifically documented to the contrary. Corresponds to SERVER CHANGE and the presence of the label CHANGE in the SERVER CHARACTERISTICS display. |
| DAT sysDateTime | 1.3.6.1.4.1.33.1.3 | DateTime | read-write | The system's current local date and time. Corresponds directly to SERVER DATE and SERVER TIME and the value in various displays. |
| OCT sysTimeZone | 1.3.6.1.4.1.33.1.4 | OCTET STRING | read-write | The adjustment to apply to a universal (Greenwich) time received when down-line loaded, comprising two octets. The first octet is the number of hours west of universal, the second is the number of minutes. Corresponds directly to SERVER TIMEZONE and the value labeled 'Timezone:' in the SERVER CHARACTERISTICS display. |
| STR sysLoadSoftware | 1.3.6.1.4.1.33.1.5 | DisplayString | read-write | The software file name to request for down-line load of the server. Corresponds directly to SERVER SOFTWARE, and the value labeled 'Software:' in the SERVER CHARACTERISTICS display. |
| INT sysDump | 1.3.6.1.4.1.33.1.6 | INTEGER | read-write | Control for dumping the system's memory when the system crashes. Corresponds directly to SERVER DUMP and the presence of 'Dump' under the label 'Enabled Characteristics' in the SERVER CHARACTERISTICS display. |
| OCT sysMaintenancePassword | 1.3.6.1.4.1.33.1.7 | OCTET STRING | read-write | The password a management system must supply to force the system to reboot or use the system's remote console via the Maintenance Operation Protocol (MOP). Corresponds directly to SERVER MAINTENANCE PASSWORD. When setting this value, the management system must supply eight octets, filling with zeros from the first octet. That is, the value '1ab42' would be expressed as '0.0.0.0.0.1.ab.42'. Setting the value to zero disables the password check. When returning this value, the agent always returns a zero length OCTET STRING. |
| STR sysLocalName | 1.3.6.1.4.1.33.1.8 | DisplayString | read-write | The system's local name. Corresponds directly to SERVER NAME and the value labeled 'Name:' in the SERVER CHARACTERISTICS display. |
| INT sysSoftwareVersionType | 1.3.6.1.4.1.33.1.9 | INTEGER | read-only | The software version variant running in the system. Corresponds to the letter in the software version in the SERVER CHARACTERISTICS display. alpha 'A': alpha test beta 'B': beta test production null: normal, production software special 'S': special, custom software |
| OCT sysSoftwareVersion | 1.3.6.1.4.1.33.1.10 | OCTET STRING | read-only | The software version running in the system. In order, the octets contain major version, minor version, ECO, and pre-release number. Corresponds to the numbers in the software version in the SERVER CHARACTERISTICS display. For example, the version display for sysSoftwareVersionType 'production' and sysSoftwareVersion '2.2.0.0' is 'V2.2'. The version display for sysSoftwareVersionType 'beta' and sysSoftwareVersion '3.1.0.4' is 'V3.1B4'. |
| INT sysRomVersion | 1.3.6.1.4.1.33.1.11 | INTEGER | read-only | The firmware version of the bootstrap ROM installed in the system. Corresponds directly to the value labeled 'Rom' in the SERVER CHARACTERISTICS display. |
| INT sysHardwareType | 1.3.6.1.4.1.33.1.12 | INTEGER | read-only | The type of hardware on which the system is running, with values as defined in Xyplex Assigned Numbers, Xyplex document number 420-0497. Corresponds directly to the value labeled 'Hardware Type:' in the UNIT display. |
| INT sysHardwareVersion | 1.3.6.1.4.1.33.1.13 | INTEGER | read-only | This version of hardware on which the system is running. Corresponds directly to part of the value labeled 'HW' in the SERVER CHARACTERISTICS display. |
| INT sysChassisType | 1.3.6.1.4.1.33.1.14 | INTEGER | read-only | The type of chassis in which the system is running. Corresponds directly to part of the value labeled 'HW' in the SERVER CHARACTERISTICS display. |
| INT sysChassisVersion | 1.3.6.1.4.1.33.1.15 | INTEGER | read-only | This version of chassis in which the system is running. Corresponds directly to part of the value labeled 'HW' in the SERVER CHARACTERISTICS display. |
| INT sysCrash | 1.3.6.1.4.1.33.1.16 | INTEGER | read-write | Control to cause this system to crash. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes an immediate crash. Corresponds to the CRASH command. |
| INT sysInitialize | 1.3.6.1.4.1.33.1.17 | INTEGER | read-write | Control to cause this system to reset its software to initial load values, typically by reloading. When executing an initialize command, the system observes the value of sysInitializeDelay as supplied anywhere in the same set request with sysInitialize. If this value is not included in the set request, the system uses its default value. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'conditionalExecute' causes initialization if the overall system state is acceptible (such as not needing to store permanent parameters). Setting it to 'unconditionalExecute' causes initialization regardless of the overall system state. Setting it to 'cancel' aborts an initialization that has not yet started. According to standard SNMP operation, if the system is not in a proper state to accept a given set request for this value, it returns the standard SNMP error 'badValue'. Corresponds to the INITIALIZE command. |
| INT sysInitializeDelay | 1.3.6.1.4.1.33.1.18 | INTEGER | read-write | The number of minutes to delay before beginning the system initialization process as executed with sysInitialize. This value cannot be set outside a set-request that contains the value 'execute' for sysInitialize. If not included in such a set, the default value is 1. Corresponds to the INITIALIZE command's DELAY parameter and to the value labeled 'Minutes to shutdown:' in the SYSTEM STATUS display. |
| INT sysZeroAll | 1.3.6.1.4.1.33.1.19 | INTEGER | read-write | Control to zero all counters. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes all the system's counters to be zeroed. Corresponds to the ZERO ALL command. |
| INT sysZeroBase | 1.3.6.1.4.1.33.1.20 | INTEGER | read-write | Control to zero all base counters. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes all the system's base counters to be zeroed. Examples of counters that are zeroed are the SNMP counters or the counters from the SYSTEM COUNTERS display. Examples of counters that are not zeroed are Ethernet interface counters or port counters. Corresponds to the ZERO SYSTEM command. |
| TIK sysZeroBaseTime | 1.3.6.1.4.1.33.1.21 | TimeTicks | read-only | The number hundredths of a second since the most recent zeroing of the base counters, such as through execution of sysZeroAll or sysZeroBase. Corresponds directly to the value labeled 'Seconds Since Zeroed:' in the SERVER COUNTERS display. |
| STR sysLoaderName | 1.3.6.1.4.1.33.1.22 | DisplayString | read-only | The name of the system that provided this system's running software. Corresponds directly to the value labeled 'Primary Host:' in the SERVER STATUS display. |
| ADR sysLoaderAddressType | 1.3.6.1.4.1.33.1.23 | AddressType | read-only | The type of network address contained in sysLoaderAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'local' means there is no address and this system's software was loaded from local storage. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. Corresponds indirectly to the value labeled 'Load Address:' in the SERVER STATUS display. |
| OCT sysLoaderAddress | 1.3.6.1.4.1.33.1.24 | OCTET STRING | read-only | The network address of the system that provided this system's running software. Corresponds directly to the value labeled 'Load Address:' in the SERVER STATUS display. |
| ADR sysDumperAddressType | 1.3.6.1.4.1.33.1.25 | AddressType | read-only | The type of network address contained in sysDumperAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'local' means there is no address and this system's was dumped to local storage. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. Corresponds indirectly to the value labeled 'Dump Address:' in the SERVER STATUS display. |
| OCT sysDumperAddress | 1.3.6.1.4.1.33.1.26 | OCTET STRING | read-only | The network address of the system that most recently accepted a crash dump from this system. Corresponds directly to the value labeled 'Dump Address:' in the SERVER STATUS display. |
| CTR sysResourceLacks | 1.3.6.1.4.1.33.1.27 | Counter | read-only | The number of times a local resource allocation failed, for example due to lack of dynamic memory. Corresponds directly to the value labeled 'Resource Errors:' in the SERVER STATUS display. |
| INT sysChassisState | 1.3.6.1.4.1.33.1.28 | INTEGER | read-only | For chassis-based systems, the state of the overall chassis. 'notApplicable' indicates the system is not chassis based. 'noFault' indicates no current chassis problem. 'fault' indicates a current chassis problem such as a card or power supply failure. Corresponds directly to the value labeled 'Crate Current State: in the SERVER ALTERNATE STATUS display. |
| CTR sysChassisFaultTransitions | 1.3.6.1.4.1.33.1.29 | Counter | read-only | The number of times this system has seen sysChassisState switch from 'noFault' to 'fault' or from 'fault' to 'noFault'. Corresponds directly to the value labeled 'Crate Transition Count: in the SERVER ALTERNATE STATUS display. |
| INT sysResourceNumber | 1.3.6.1.4.1.33.1.30 | INTEGER | read-only | The number of resource entries in the Resource table. |
| INT sysFeatureNumber | 1.3.6.1.4.1.33.1.31 | INTEGER | read-only | The number of feature entries in the Feature table. |
| resTable | 1.3.6.1.4.1.33.1.32 | not-accessible | A list of resource entries. The number of entries is given by the value of sysResourceNumber. | |
| resEntry | 1.3.6.1.4.1.33.1.32.1 | not-accessible | Status values for a system resource. | |
| INT resType | 1.3.6.1.4.1.33.1.32.1.1 | INTEGER | read-only | Identification of a resource type. Typically corresponds directly to a label such as 'Processes:' in the SERVER ALTERNATE STATUS display. |
| GAU resCurrent | 1.3.6.1.4.1.33.1.32.1.2 | Gauge | read-only | The number of resources currently in use on the system. Typically corresponds directly to a value labeled 'Cur' in the SERVER ALTERNATE STATUS display. |
| GAU resWorst | 1.3.6.1.4.1.33.1.32.1.3 | Gauge | read-only | The highest or lowest value of resCurrent since system initialization. Typically corresponds directly to a value labeled 'High' or 'Low' in the SERVER ALTERNATE STATUS display. |
| INT resAdminMaximum | 1.3.6.1.4.1.33.1.32.1.4 | INTEGER | read-write | The desired maximum possible number of resources in the system. In many cases, ACCESS to this object for a particular resType is read-only. Typically corresponds directly to a value labeled 'Max' in the SERVER ALTERNATE STATUS display for desired, administrative values. When the desired change takes effect is implementation specific, ranging from immediately to the next system initialization. |
| CTR resLacks | 1.3.6.1.4.1.33.1.32.1.5 | Counter | read-only | The number of times since system initialization that the system could not obtain the resource because none were available. Typically corresponds directly to a value labeled 'Failure' in the SERVER ALTERNATE STATUS display. If such failures do not apply to the particular resource, such as 'cpuPercent', the agent returns zero for this object. |
| DAT resLackTime | 1.3.6.1.4.1.33.1.32.1.6 | DateTime | read-only | The local system date and time when resLack last increased. Typically corresponds directly to a value labeled 'Last Occurred' in the SERVER ALTERNATE STATUS display. If such failures do not apply to the particular resource, such as 'cpuPercent', the agent returns all zeroes (unknown) for this object. |
| INT resOperMaximum | 1.3.6.1.4.1.33.1.32.1.7 | INTEGER | read-only | The current maximum possible number of resources in the system. Typically corresponds directly to a value labeled 'Max' in the SERVER ALTERNATE STATUS display for current operational values. This value is based on current or previous value of resAdminMaximum. |
| featTable | 1.3.6.1.4.1.33.1.33 | not-accessible | A list of feature entries. The number of entries is given by the value of sysFeatureNumber. | |
| featEntry | 1.3.6.1.4.1.33.1.33.1 | not-accessible | Status values for a system feature. | |
| INT featType | 1.3.6.1.4.1.33.1.33.1.1 | INTEGER | read-only | Identification of a feature type. Corresponds to a SERVER feature keyword. |
| INT featStatus | 1.3.6.1.4.1.33.1.33.1.2 | INTEGER | read-write | The status of the feature as of the next system initialization. Corresponds to the presence of the feature's lable following the label 'Enabled Feature(s): in the UNIT display. |
| bootControl | 1.3.6.1.4.1.33.1.34 | |||
| STR bootControlLoadInternetFile | 1.3.6.1.4.1.33.1.34.1 | DisplayString | read-write | The filename to request when loading an image via TFTP. Corresponds directly to SERVER INTERNET LOAD FILE and the value labeled 'Internet Load File:' in the SERVER BOOT CHARACTERISTICS display. |
| IP bootControlLoadInternetServer | 1.3.6.1.4.1.33.1.34.2 | IpAddress | read-write | The internet address of the server to use when loading an image via TFTP. Corresponds directly to SERVER INTERNET LOAD HOST and the value labeled 'Internet Load Host:' in the SERVER BOOT CHARACTERISTICS display. |
| IP bootControlLoadInternetGateway | 1.3.6.1.4.1.33.1.34.3 | IpAddress | read-write | The internet address of the gateway to use when loading an image via TFTP. Corresponds directly to SERVER INTERNET LOAD GATEWAY and the value labeled 'Internet Load Gateway:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadBootpTftp | 1.3.6.1.4.1.33.1.34.4 | INTEGER | read-write | Control for loading via the combination of BOOTP and TFTP. Corresponds to SERVER LOAD PROTOCOL BOOTPTFTP and the presence of 'BOOTP/TFTP/' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadTftpDirect | 1.3.6.1.4.1.33.1.34.5 | INTEGER | read-write | Control for loading via directed TFTP. Corresponds to SERVER LOAD PROTOCOL TFTPDIRECT and the presence of 'TFTPDIRECT' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadLocal | 1.3.6.1.4.1.33.1.34.6 | INTEGER | read-write | Control for loading from a local medium. Corresponds to SERVER LOAD PROTOCOL LOCAL and the presence of 'LOCAL' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadMop | 1.3.6.1.4.1.33.1.34.7 | INTEGER | read-write | Control for loading via DEC MOP. Corresponds to SERVER LOAD PROTOCOL MOP and the presence of 'MOP' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadProprietary | 1.3.6.1.4.1.33.1.34.8 | INTEGER | read-write | Control for loading via Xyplex-proprietary extended MOP. Corresponds to SERVER LOAD PROTOCOL PROPRIETARY and the presence of 'Proprietary' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadRarpTftp | 1.3.6.1.4.1.33.1.34.9 | INTEGER | read-write | Control for loading via the combination of RARP and TFTP. Corresponds to SERVER LOAD PROTOCOL RARPTFTP and the presence of 'RARP/TFTP' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlDumpBootpTftp | 1.3.6.1.4.1.33.1.34.10 | INTEGER | read-write | Control for dumping via the combination of BOOTP and TFTP. Corresponds to SERVER DUMP PROTOCOL BOOTPTFTP and the presence of 'BOOTP/TFTP' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlDumpLocal | 1.3.6.1.4.1.33.1.34.11 | INTEGER | read-write | Control for dumping to a local medium. Corresponds to SERVER DUMP PROTOCOL LOCAL and the presence of 'Local' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlDumpMop | 1.3.6.1.4.1.33.1.34.12 | INTEGER | read-write | Control for dumping via DEC MOP. Corresponds to SERVER DUMP PROTOCOL MOP and the presence of 'MOP' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlDumpProprietary | 1.3.6.1.4.1.33.1.34.13 | INTEGER | read-write | Control for dumping via Xyplex-proprietary extended MOP. Corresponds to SERVER DUMP PROTOCOL PROPRIETARY and the presence of 'Proprietary' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlDumpRarpTftp | 1.3.6.1.4.1.33.1.34.14 | INTEGER | read-write | Control for dumping via the combination of RARP and TFTP. Corresponds to SERVER DUMP PROTOCOL RARPTFTP and the presence of 'RARP/TFTP' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlParamBootpTftp | 1.3.6.1.4.1.33.1.34.15 | INTEGER | read-write | Control for loading parameters via the combination of BOOTP and TFTP. Corresponds to SERVER PARAMETER PROTOCOL MOP and the presence of 'BOOTP/TFTP' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlParamLocal | 1.3.6.1.4.1.33.1.34.16 | INTEGER | read-write | Control for loading parameters from a local medium. Corresponds to SERVER PARAMETER PROTOCOL LOCAL and the presence of 'LOCAL' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlParamMop | 1.3.6.1.4.1.33.1.34.17 | INTEGER | read-write | Control for loading parameters via DEC MOP. Corresponds to SERVER PARAMETER PROTOCOL MOP and the presence of 'MOP' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlParamProprietary | 1.3.6.1.4.1.33.1.34.18 | INTEGER | read-write | Control for loading parameters via Xyplex-proprietary extended MOP. Corresponds to SERVER PARAMETER PROTOCOL PROPRIETARY and the presence of 'Proprietary' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlParamRarpTftp | 1.3.6.1.4.1.33.1.34.19 | INTEGER | read-write | Control for loading parameters via the combination of RARP and TFTP. Corresponds to SERVER PARAMETER PROTOCOL RARPTFTP and the presence of 'RARP/TFTP' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| GAU sysInstalledMemory | 1.3.6.1.4.1.33.1.35 | Gauge | read-only | The total number of bytes of main memory installed in the system. Corresponds directly to the value labeled 'Installed' on the SERVER ALTERNATE STATUS display. |
| characterDep | 1.3.6.1.4.1.33.2 | |||
| lat | 1.3.6.1.4.1.33.3 | |||
| INT latAnnounceServices | 1.3.6.1.4.1.33.3.1 | INTEGER | read-write | Control for automatic, periodic announcement of local services to the network. Corresponds directly to SERVER ANNOUNCEMENTS and the presence of the label 'Announcements' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| INT latCircuitTimer | 1.3.6.1.4.1.33.3.2 | INTEGER | read-write | Number of milleseconds to collect port input data before sending it to the host. Corresponds directly to SERVER CIRCUIT TIMER and the value labeled 'Circuit Timer:' in the SERVER CHARACTERISTICS display. |
| INT latIdentificationLengthLimit | 1.3.6.1.4.1.33.3.3 | INTEGER | read-write | Maximum number of characters to store in the instances of latVisibleServiceIdentification. Corresponds directly to SERVER IDENTIFICATION SIZE and the value labeled 'Identification Size:' in the SERVER CHARACTERISTICS display. |
| INT latKeepaliveTimer | 1.3.6.1.4.1.33.3.4 | INTEGER | read-write | Number of seconds of inactivity before sending a null message to the host. Corresponds directly to SERVER KEEPALIVE TIMER and the value labeled 'Keepalive Timer:' in the SERVER CHARACTERISTICS display. |
| INT latMulticastTimer | 1.3.6.1.4.1.33.3.5 | INTEGER | read-write | Number of seconds between transmission of local service announcements. Corresponds directly to SERVER MULTICAST TIMER and the value labeled 'Multicast Timer:' in the SERVER CHARACTERISTICS display. |
| INT latNodeLimit | 1.3.6.1.4.1.33.3.6 | INTEGER | read-write | Maximum number of service nodes to keep in the node table. Corresponds directly to SERVER NODE LIMIT and the value labeled 'Node Limit:' in the SERVER CHARACTERISTICS display. |
| INT latNumber | 1.3.6.1.4.1.33.3.7 | INTEGER | read-write | An arbitrary number assigned and used for administrative purposes. Corresponds directly to SERVER NUMBER and the value labeled 'Number:' in the SERVER CHARACTERISTICS display. |
| INT latRetransmitLimit | 1.3.6.1.4.1.33.3.8 | INTEGER | read-write | Maximum number of times to retransmit an unacknowledged message. Corresponds directly to SERVER RETRANSMIT LIMIT and the value labeled 'Retransmit Limit:' in the SERVER CHARACTERISTICS display. |
| OCT latLocalServiceGroups | 1.3.6.1.4.1.33.3.9 | OCTET STRING | read-write | The list of group numbers allowed to use local services, where a group number is in the range 0-255. The OCTET STRING contains a bitmap, with one bit for each group. Corresponding bit numbers start with 0 as the high-order bit of the first octet. Corresponds directly to SERVER SERVICE GROUPS and the value labeled 'Service Groups:' in the SERVER CHARACTERISTICS display. |
| INT latGroupPurge | 1.3.6.1.4.1.33.3.10 | INTEGER | read-write | Control for automatic deletion of all node table entries when latServiceGroups or latPortCurrentGroups is changed. Corresponds directly to SERVER PURGE GROUP and the presence of the label 'Purge Group' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| INT latNodePurge | 1.3.6.1.4.1.33.3.11 | INTEGER | read-write | Control for automatic deletion of all node table entries with status 'reachable' when the number of entries exceeds latNodeLimit. Corresponds directly to SERVER PURGE NODE and the presence of the label 'Purge Node' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| CTR latNodesRejected | 1.3.6.1.4.1.33.3.12 | Counter | read-only | Number of nodes not added to the node table because there was no room. Corresponds directly to the value labeled 'Discarded Nodes:' in the SERVER STATUS display. |
| CTR latInMessages | 1.3.6.1.4.1.33.3.13 | Counter | read-only | Number of LAT messages received. Corresponds directly to the value labeled 'Messages Received:' in the SERVER COUNTERS display. |
| CTR latOutMessages | 1.3.6.1.4.1.33.3.14 | Counter | read-only | Number of LAT messages sent. Corresponds directly to the value labeled 'Messages Transmitted:' in the SERVER COUNTERS display. |
| CTR latInSessionsAccepted | 1.3.6.1.4.1.33.3.15 | Counter | read-only | Number of incoming LAT session connection attempts accepted. Corresponds directly to the value labeled 'Solicitations Accepted:' in the SERVER COUNTERS display. |
| CTR latInSessionsRejected | 1.3.6.1.4.1.33.3.16 | Counter | read-only | Number of incoming LAT session connection attempts rejected. Corresponds directly to the value labeled 'Solicitations Rejected:' in the SERVER COUNTERS display. |
| CTR latAddressChange | 1.3.6.1.4.1.33.3.17 | Counter | read-only | Number of times a service announcement contained a node name already in the visible service table but with a different address. Corresponds directly to the value labeled 'Multiple Node Addresses:' in the SERVER COUNTERS display. |
| CTR latInDuplicates | 1.3.6.1.4.1.33.3.18 | Counter | read-only | Number of duplicate LAT messages received. Corresponds directly to the value labeled 'Duplicates Received:' in the SERVER COUNTERS display. |
| CTR latOutRetransmits | 1.3.6.1.4.1.33.3.19 | Counter | read-only | Number of LAT messages retransmitted due to no acknowledgement. Corresponds directly to the value labeled 'Messages Re-transmitted:' in the SERVER COUNTERS display. |
| CTR latInBadMessages | 1.3.6.1.4.1.33.3.20 | Counter | read-only | Number of LAT messages received with invalid format. Corresponds directly to the value labeled 'Illegal Messages Rcv'd:' in the SERVER COUNTERS display. |
| CTR latInBadSlots | 1.3.6.1.4.1.33.3.21 | Counter | read-only | Number of LAT messages received with invalid slot format. Corresponds directly to the value labeled 'Illegal Slots Rcv'd:' in the SERVER COUNTERS display. |
| CTR latInBadMulticasts | 1.3.6.1.4.1.33.3.22 | Counter | read-only | Number of multicast LAT messages received with invalid format. Corresponds directly to the value labeled 'Illegal Multicasts Rcv'd:' in the SERVER COUNTERS display. |
| latPortTable | 1.3.6.1.4.1.33.3.23 | not-accessible | A list of LAT character port entries. | |
| latPortEntry | 1.3.6.1.4.1.33.3.23.1 | not-accessible | LAT parameter values for a port. | |
| INT latPortIndex | 1.3.6.1.4.1.33.3.23.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Character MIB [11]. |
| OCT latPortAuthorizedGroups | 1.3.6.1.4.1.33.3.23.1.2 | OCTET STRING | read-write | The list of group numbers to which the port is allowed to set access, where a group number is in the range 0-255. The OCTET STRING contains a bitmap, with one bit for each group. Corresponding bit numbers start with 0 as the high-order bit of the first octet. Corresponds directly to PORT AUTHORIZED GROUPS and the value labeled 'Authorized Groups:' in the PORT CHARACTERISTICS display. |
| INT latPortAutoPrompt | 1.3.6.1.4.1.33.3.23.1.3 | INTEGER | read-write | Control for automatic stimulation of a host prompt upon forming a new session. Corresponds directly to PORT AUTOPROMPT and the presence of the label 'Autoprompt' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| OCT latPortCurrentGroups | 1.3.6.1.4.1.33.3.23.1.4 | OCTET STRING | read-write | The list of group numbers to which the port currently has set access, where a group number is in the range 0-255. The OCTET STRING contains a bitmap, with one bit for each group. Corresponding bit numbers start with 0 as the high-order bit of the first octet. Corresponds directly to PORT GROUPS and the value labeled 'Groups:' in the PORT CHARACTERISTICS display. |
| INT latPortRemoteModification | 1.3.6.1.4.1.33.3.23.1.5 | INTEGER | read-write | Control to allow the remote system to modify certain physical port characteristics. Corresponds directly to PORT REMOTE MODIFICATION and the presence of the label 'Remote Modification' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| latOfferedServiceTable | 1.3.6.1.4.1.33.3.24 | not-accessible | A list of offered service entries. | |
| latOfferedServiceEntry | 1.3.6.1.4.1.33.3.24.1 | not-accessible | Parameter values for an offered service entry. | |
| STR latOfferedServiceName | 1.3.6.1.4.1.33.3.24.1.1 | DisplayString | read-write | The name of an offered service. Corresponds directly to the name in a SERVICE command and the value labeled 'Service:' in the SERVICE CHARACTERISTICS display. |
| INT latOfferedServiceStatus | 1.3.6.1.4.1.33.3.24.1.2 | INTEGER | read-write | The status of the entry. Set to 'invalid' to remove the entry, which corresponds directly to the CLEAR SERVICE command. Actual removal of the entry is implementation specific. |
| INT latOfferedServiceAllowConnections | 1.3.6.1.4.1.33.3.24.1.3 | INTEGER | read-write | Control for allowing incoming connections to the service. Corresponds directly to SERVICE CONNECTIONS and the presence of the label 'Connections' following the label 'Enabled Characteristics:' in the SERVICE CHARACTERISTICS display. |
| STR latOfferedServiceIdentification | 1.3.6.1.4.1.33.3.24.1.4 | DisplayString | read-write | Text to identify a service. Corresponds directly to SERVICE IDENTIFICATION and the value labeled 'Identification:' in the SERVICE CHARACTERISTICS display. |
| STR latOfferedServicePassword | 1.3.6.1.4.1.33.3.24.1.5 | DisplayString | read-write | The password a user must supply to use the service. Corresponds directly to SERVICE PASSWORD and the presence of the label 'Password' following the label 'Enabled Characteristics:' in the SERVICE CHARACTERISTICS display. When setting this value, the management system must supply eight octets, filling with zeros from the first octet. That is, the value '1ab42' would be expressed as '0.0.0.0.0.1.ab.42'. Setting the value to zero disables the password check. When returning this value, the agent always returns a zero length OCTET STRING. |
| OCT latOfferedServicePortMap | 1.3.6.1.4.1.33.3.24.1.6 | OCTET STRING | read-write | The list of character ports offer the service. The OCTET STRING contains a bitmap, with one bit for each port, and enough octets for all the ports on the system. Port numbers are as defined for charPortIndex in the Character MIB [11]. Corresponding bit numbers start with 1 as the high-order bit of the first octet. Corresponds directly to port-list portion of SERVICE PORTS and the value labeled 'Ports:' in the SERVICE CHARACTERISTICS display. |
| INT latOfferedServiceQueuing | 1.3.6.1.4.1.33.3.24.1.7 | INTEGER | read-write | Control for allowing queuing of incoming connections to the service when the service is busy. Corresponds directly to SERVICE QUEUE and the presence of the label 'Queuing' following the label 'Enabled Characteristics:' in the SERVICE CHARACTERISTICS display. |
| latVisibleServiceTable | 1.3.6.1.4.1.33.3.25 | not-accessible | A list of visible service entries. | |
| latVisibleServiceEntry | 1.3.6.1.4.1.33.3.25.1 | not-accessible | Parameter values for a visible service entry. | |
| STR latVisibleServiceName | 1.3.6.1.4.1.33.3.25.1.1 | DisplayString | read-only | The name of a visible service. Corresponds directly to the name in a SERVICE command and the value labeled 'Service Name' in the SERVICE SUMMARY display. |
| INT latVisibleServiceStatus | 1.3.6.1.4.1.33.3.25.1.2 | INTEGER | read-only | Status of communication with the service. Corresponds directly to the value labeled 'Status' in the SERVICE SUMMARY display. |
| STR latVisibleServiceNode | 1.3.6.1.4.1.33.3.25.1.3 | DisplayString | read-only | Name of a node offering the service. Corresponds directly to the value labeled Node Name in the SERVICE STATUS display. |
| GAU latVisibleServiceConnectedSessions | 1.3.6.1.4.1.33.3.25.1.4 | Gauge | read-only | Number of connected sessions to the service. Corresponds directly to the number with the value 'Connected', labeled 'Status' in the SERVICE SUMMARY display. |
| STR latVisibleServiceIdentification | 1.3.6.1.4.1.33.3.25.1.5 | DisplayString | read-only | Text to identify a service. The length is subject to limitation by latIdentificationLengthLimit. Corresponds directly to the value labeled 'Identification:' in the SERVICE SUMMARY display. |
| GAU latVisibleServiceRating | 1.3.6.1.4.1.33.3.25.1.6 | Gauge | read-only | Relative capacity of the service to accept additional sessions. Corresponds directly to value labeled Rating in the SERVICE STATUS display. |
| latNodeTable | 1.3.6.1.4.1.33.3.26 | not-accessible | A list of node entries. | |
| latNodeEntry | 1.3.6.1.4.1.33.3.26.1 | not-accessible | Parameter values for a node entry. | |
| STR latNodeName | 1.3.6.1.4.1.33.3.26.1.1 | DisplayString | read-only | The name of a node. Corresponds directly to the value labeled 'Node:' in the NODE STATUS display. |
| INT latNodeStatus | 1.3.6.1.4.1.33.3.26.1.2 | INTEGER | read-only | Status of communication with the node. Corresponds directly to the value labeled 'Status' in the NODE STATUS display. |
| GAU latNodeConnectedSessions | 1.3.6.1.4.1.33.3.26.1.3 | Gauge | read-only | Number of connected sessions to the node. Corresponds directly to the number with the value 'Connected', labeled 'Status' in the NODE STATUS display. |
| OCT latNodeAddress | 1.3.6.1.4.1.33.3.26.1.4 | OCTET STRING | read-only | Ethernet address of the node. Corresponds directly to the value labeled 'Address:' in the NODE STATUS display. |
| INT latNodeDataLinkFrame | 1.3.6.1.4.1.33.3.26.1.5 | INTEGER | read-only | Maximum Ethernet frame used by the node. Corresponds directly to the value labeled 'Data Link Frame Size:' in the NODE STATUS display. |
| STR latNodeIdentification | 1.3.6.1.4.1.33.3.26.1.6 | DisplayString | read-only | Text that identifies the node. The size is subject to limitation by latIdentificationLengtLimit. Corresponds directly to the value labeled 'Identification' in the NODE STATUS display. |
| OCT latNodeGroups | 1.3.6.1.4.1.33.3.26.1.7 | OCTET STRING | read-write | The list of group numbers to which the node belongs, where a group number is in the range 0-255. The OCTET STRING contains a bitmap, with one bit for each group. Corresponding bit numbers start with 0 as the high-order bit of the first octet. Corresponds directly to the value labeled 'Node Groups:' in the NODE STATUS display. |
| GAU latNodeServiceNumber | 1.3.6.1.4.1.33.3.26.1.8 | Gauge | read-only | Number of entries for the node in the node service table. Corresponds indirectly to the list of services in the NODE STATUS display. |
| INT latNodeZero | 1.3.6.1.4.1.33.3.26.1.9 | INTEGER | read-write | Control to zero counters kept for the node. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes all the system's counters to be zeroed. Corresponds to the ZERO NODE command. |
| TIK latNodeZeroTime | 1.3.6.1.4.1.33.3.26.1.10 | TimeTicks | read-only | The number of hundredths of a second since the most recent zeroing of the counters kept for the node, such as through execution of sysZeroAll or latNodeZero. Corresponds directly to the value labeled 'Seconds Since Zeroed:' in the NODE COUNTERS display. |
| CTR latNodeInMessages | 1.3.6.1.4.1.33.3.26.1.11 | Counter | read-only | The number of LAT messages received from the node. Corresponds directly to the value labeled 'Messages Received:' in the NODE COUNTERS display. |
| CTR latNodeOutMessages | 1.3.6.1.4.1.33.3.26.1.12 | Counter | read-only | The number of LAT messages sent to the node. Corresponds directly to the value labeled 'Messages Transmitted:' in the NODE COUNTERS display. |
| CTR latNodeInSlots | 1.3.6.1.4.1.33.3.26.1.13 | Counter | read-only | The number of LAT slots received from the node. Corresponds directly to the value labeled 'Slots Received:' in the NODE COUNTERS display. |
| CTR latNodeOutSlots | 1.3.6.1.4.1.33.3.26.1.14 | Counter | read-only | The number of LAT slots sent to the node. Corresponds directly to the value labeled 'Slots Transmitted:' in the NODE COUNTERS display. |
| CTR latNodeInBytes | 1.3.6.1.4.1.33.3.26.1.15 | Counter | read-only | The total number of bytes received from the node, including Ethernet overhead. Corresponds directly to the value labeled 'Bytes Received:' in the NODE COUNTERS display. |
| CTR latNodeOutBytes | 1.3.6.1.4.1.33.3.26.1.16 | Counter | read-only | The total number of bytes sent to the node, including Ethernet overhead. Corresponds directly to the value labeled 'Bytes Transmitted:' in the NODE COUNTERS display. |
| CTR latNodeAddressChange | 1.3.6.1.4.1.33.3.26.1.17 | Counter | read-only | The number of times a LAT message multicast by the node had a different Ethernet address from the previous time. Corresponds directly to the value labeled 'Multiple Node Addresses:' in the NODE COUNTERS display. |
| CTR latNodeInDuplicates | 1.3.6.1.4.1.33.3.26.1.18 | Counter | read-only | The number of duplicate LAT message received from the node. Corresponds directly to the value labeled 'Duplicates Received:' in the NODE COUNTERS display. |
| CTR latNodeOutRetransmits | 1.3.6.1.4.1.33.3.26.1.19 | Counter | read-only | The number of LAT message retransmitted to the node due to lack of acknowledgement. Corresponds directly to the value labeled 'Messages Re-transmitted:' in the NODE COUNTERS display. |
| CTR latNodeInBadMessages | 1.3.6.1.4.1.33.3.26.1.20 | Counter | read-only | The number of LAT message received from the node with invalid format. Corresponds directly to the value labeled 'Illegal Messages Received:' in the NODE COUNTERS display. |
| CTR latNodeInBadSlots | 1.3.6.1.4.1.33.3.26.1.21 | Counter | read-only | The number of LAT slots received from the node with invalid format. Corresponds directly to the value labeled 'Illegal Slots Received:' in the NODE COUNTERS display. |
| CTR latNodeInSessionsAccepted | 1.3.6.1.4.1.33.3.26.1.22 | Counter | read-only | The number of LAT session connection attempts received from the node and accepted. Corresponds directly to the value labeled 'Solicitations Accepted:' in the NODE COUNTERS display. |
| CTR latNodeInSessionsRejected | 1.3.6.1.4.1.33.3.26.1.23 | Counter | read-only | The number of LAT session connection attempts received from the node and rejected. Corresponds directly to the value labeled 'Solicitations Rejected:' in the NODE COUNTERS display. |
| xInternetDep | 1.3.6.1.4.1.33.4 | |||
| bootServer | 1.3.6.1.4.1.33.6 | |||
| bsBasic | 1.3.6.1.4.1.33.6.1 | |||
| INT basicLogLimit | 1.3.6.1.4.1.33.6.1.1 | INTEGER | read-write | Maximum allowed number of kilobytes for recording events. Corresponds directly to MANAGER LOG FILE SIZE and the value labeled 'Log File Size:' in the MANAGER CHARACTERISTICS display. |
| INT basicActiveLimit | 1.3.6.1.4.1.33.6.1.2 | INTEGER | read-write | Maximum allowed number of simultaneous service dialogs. Corresponds directly to MANAGER SIMULTANEOUS and the value labeled 'Maximum simultaneous requests:' in the MANAGER CHARACTERISTICS display. |
| GAU basicActiveNumber | 1.3.6.1.4.1.33.6.1.3 | Gauge | read-only | Number of active service dialogs. Corresponds indirectly to the list of active clients in the MANAGER STATUS display. |
| GAU basicClientNumber | 1.3.6.1.4.1.33.6.1.4 | Gauge | read-only | Number of defined clients. Corresponds indirectly to the list of defined clients in the MANAGER LOCAL, MANAGER GLOBAL, and MANAGER NODE displays. |
| CTR basicOffersSent | 1.3.6.1.4.1.33.6.1.5 | Counter | read-only | Total number of service offers sent in response to client requests. Corresponds directly to the value labeled 'Total service offers sent:' in the MANAGER STATUS display. |
| GAU basicEventTotal | 1.3.6.1.4.1.33.6.1.6 | Gauge | read-only | Total number of events that have been written to the event log since it was last purged. This may be less than the number currently in the log. Corresponds directly to the value labeled 'Total Messages Logged:' in the MANAGER EVENTS display. |
| INT basicEventPurge | 1.3.6.1.4.1.33.6.1.7 | INTEGER | read-write | Control to cause emptying the event log. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes the event log to immediately become empty. Corresponds directly to the PURGE MANAGER LOG FILE command. |
| activeTable | 1.3.6.1.4.1.33.6.1.8 | not-accessible | A list of active client dialog entries. The number of entries is given by basicActiveNumber. | |
| activeEntry | 1.3.6.1.4.1.33.6.1.8.1 | not-accessible | Parameter values for an active client dialog entry. | |
| ADR activeIdentificationType | 1.3.6.1.4.1.33.6.1.8.1.1 | AddressType | read-only | The type of identification value in activeIdentification. Corresponds indirectly to the value labeled 'EthernetAddress' in the MANAGER STATUS display. |
| OCT activeIdentification | 1.3.6.1.4.1.33.6.1.8.1.2 | OCTET STRING | read-only | Identification of the active partner. Corresponds directly to the value labeled 'EthernetAddress' in the MANAGER STATUS display. |
| INT activeFunction | 1.3.6.1.4.1.33.6.1.8.1.3 | INTEGER | read-only | The function the server is performing with the partner. Corresponds directly to the value labeled 'Function' in the MANAGER STATUS display. |
| INT activeSoftwareVersionType | 1.3.6.1.4.1.33.6.1.8.1.4 | INTEGER | read-only | If activeFunction is 'load', the software version being sent to the client, otherwise 'notApplicable'. Corresponds to the letter in the software version labeled 'Version' in the MANAGER STATUS display. alpha 'A': alpha test beta 'B': beta test production null: normal, production software special 'S': special, custom software |
| OCT activeSoftwareVersion | 1.3.6.1.4.1.33.6.1.8.1.5 | OCTET STRING | read-only | If activeFunction is 'load', the 4-byte software version being sent to the client, otherwise zero length. In order, the octets contain major version, minor version, ECO, and pre-release number. Corresponds to the numbers in the software version labeled 'Version' in the MANAGER STATUS display. For example, the version display for activeSoftwareVersionType 'production' and activeSoftwareVersion '2.2.0.0' is 'V2.2'. The version display for activeSoftwareVersionType 'beta' and activeSoftwareVersion '3.1.0.4' is 'V3.1B4'. |
| INT activeParameterVersion | 1.3.6.1.4.1.33.6.1.8.1.6 | INTEGER | read-only | If activeFunction is 'parameterStore', the parameter version being stored by the client, otherwise zero. Corresponds directly to the value labeled 'Version' in the MANAGER STATUS display. |
| INT activeCurrentSequence | 1.3.6.1.4.1.33.6.1.8.1.7 | INTEGER | read-only | The current dialog sequence number. Corresponds directly to the value labeled 'Seq' in the MANAGER STATUS display. |
| INT activeBytesRemaining | 1.3.6.1.4.1.33.6.1.8.1.8 | INTEGER | read-only | The number of bytes remaining to be transferred in the dialog. Corresponds directly to the value labeled 'Left' in the MANAGER STATUS display. |
| STR activeFile | 1.3.6.1.4.1.33.6.1.8.1.9 | DisplayString | read-only | The name of the file being used in the dialog. Corresponds directly to the value labeled 'File' in the MANAGER STATUS display. |
| INT activeStatus | 1.3.6.1.4.1.33.6.1.8.1.10 | INTEGER | read-only | The final status of the most recent attempt to get an image. Corresponds directly to the value labeled 'Get Status:' in the DEVICE STATUS display. |
| INT activeState | 1.3.6.1.4.1.33.6.1.8.1.11 | INTEGER | read-only | The dynamic state of an active attempt to get an image. Corresponds directly to the value labeled 'Get State:' in the DEVICE STATUS display. |
| clientTable | 1.3.6.1.4.1.33.6.1.9 | not-accessible | A list of client data base entries. The number of entries is given by basicClientNumber. | |
| clientEntry | 1.3.6.1.4.1.33.6.1.9.1 | not-accessible | Parameter values for a client data base entry. | |
| ADR clientIdentificationType | 1.3.6.1.4.1.33.6.1.9.1.1 | AddressType | read-write | The type of identification value in clientIdentification. Corresponds directly to MANAGER NODE, MANAGER GLOBAL, and MANAGER LOCAL, and the value labeled 'Ethernet Address' in the MANAGER NODE display or 'Ethernet Address', 'Device', and 'Global Devices' or 'Local Devices' in the MANAGER GLOBAL and LOCAL displays. |
| OCT clientIdentification | 1.3.6.1.4.1.33.6.1.9.1.2 | OCTET STRING | read-write | Identification of the client, either a hardware type or an Ethernet address, depending on clientIdentificationType. Corresponds directly to MANAGER NODE, MANAGER GLOBAL, and MANAGER LOCAL, and the value labeled 'Ethernet Address' in the MANAGER NODE display or 'Ethernet Address', 'Device', and 'Global Devices' or 'Local Devices' in the MANAGER GLOBAL and LOCAL displays. |
| INT clientEntryStatus | 1.3.6.1.4.1.33.6.1.9.1.3 | INTEGER | read-write | The status of the entry. Set to 'invalid' to remove the entry, which corresponds directly to the PURGE LOCAL, PURGE GLOBAL, and PURGE NODE commands. Actual removal of the entry is implementation specific. |
| STR clientName | 1.3.6.1.4.1.33.6.1.9.1.4 | DisplayString | read-write | A name that may be used to identify the client. Corresponds directly to the value labeled 'Name' in the MANAGER NODE display. |
| STR clientLoadFile | 1.3.6.1.4.1.33.6.1.9.1.5 | DisplayString | read-write | The file with the client's load image. Corresponds directly to the value labeled 'Load File' in the MANAGER LOCAL, MANAGER GLOBAL, and MANAGER NODE displays. |
| STR clientDiagnosticFile | 1.3.6.1.4.1.33.6.1.9.1.6 | DisplayString | read-write | The file with the client's diagnostic test image. Corresponds directly to the value labeled 'Diag File' in the MANAGER LOCAL, MANAGER GLOBAL, and MANAGER NODE displays. |
| INT clientLoadService | 1.3.6.1.4.1.33.6.1.9.1.7 | INTEGER | read-write | Control for allowing load service for the client. Corresponds directly to the value labeled 'Load' in the MANAGER LOCAL, MANAGER GLOBAL, and MANAGER NODE displays. |
| INT clientDumpService | 1.3.6.1.4.1.33.6.1.9.1.8 | INTEGER | read-write | Control for allowing dump service for the client. Corresponds directly to the value labeled 'Dump' in the MANAGER LOCAL, MANAGER GLOBAL, and MANAGER NODE displays. |
| namedTable | 1.3.6.1.4.1.33.6.1.10 | not-accessible | A list of named client data base entries. The number of entries is given by basicClientNumber. | |
| namedEntry | 1.3.6.1.4.1.33.6.1.10.1 | not-accessible | Parameter values for a named client data base entry. | |
| ADR namedIdentificationType | 1.3.6.1.4.1.33.6.1.10.1.1 | AddressType | read-write | The type of identification value in namedIdentification. Corresponds directly to MANAGER NODE, MANAGER GLOBAL, and MANAGER LOCAL, and the value labeled 'Ethernet Address' in the MANAGER NODE display or 'Ethernet Address', 'Device', and 'Global Devices' or 'Local Devices' in the MANAGER GLOBAL and LOCAL displays. |
| OCT namedIdentification | 1.3.6.1.4.1.33.6.1.10.1.2 | OCTET STRING | read-write | Identification of the client, either a hardware type or an Ethernet address, depending on namedIdentificationType. Corresponds directly to MANAGER NODE, MANAGER GLOBAL, and MANAGER LOCAL, and the value labeled 'Ethernet Address' in the MANAGER NODE display or 'Ethernet Address', 'Device', and 'Global Devices' or 'Local Devices' in the MANAGER GLOBAL and LOCAL displays. |
| INT namedEntryStatus | 1.3.6.1.4.1.33.6.1.10.1.3 | INTEGER | read-write | The status of the entry. Set to 'invalid' to remove the entry, which corresponds directly to the PURGE LOCAL, PURGE GLOBAL, and PURGE NODE commands. Actual removal of the entry is implementation specific. |
| STR namedName | 1.3.6.1.4.1.33.6.1.10.1.4 | DisplayString | read-write | A name that may be used to identify the client. Corresponds directly to the value labeled 'Name' in the MANAGER NODE display. |
| STR namedLoadFile | 1.3.6.1.4.1.33.6.1.10.1.5 | DisplayString | read-write | The file with the client's load image. Corresponds directly to the value labeled 'Load File' in the MANAGER LOCAL, MANAGER GLOBAL, and MANAGER NODE displays. |
| STR namedDiagnosticFile | 1.3.6.1.4.1.33.6.1.10.1.6 | DisplayString | read-write | The file with the client's diagnostic test image. Corresponds directly to the value labeled 'Diag File' in the MANAGER LOCAL, MANAGER GLOBAL, and MANAGER NODE displays. |
| INT namedLoadService | 1.3.6.1.4.1.33.6.1.10.1.7 | INTEGER | read-write | Control for allowing load service for the client. Corresponds directly to the value labeled 'Load' in the MANAGER LOCAL, MANAGER GLOBAL, and MANAGER NODE displays. |
| INT namedDumpService | 1.3.6.1.4.1.33.6.1.10.1.8 | INTEGER | read-write | Control for allowing dump service for the client. Corresponds directly to the value labeled 'Dump' in the MANAGER LOCAL, MANAGER GLOBAL, and MANAGER NODE displays. |
| eventTable | 1.3.6.1.4.1.33.6.1.11 | not-accessible | A list of event entries. The number of entries is given by basicEventNumber. | |
| eventEntry | 1.3.6.1.4.1.33.6.1.11.1 | not-accessible | Parameter values for a event entry. | |
| INT eventIndex | 1.3.6.1.4.1.33.6.1.11.1.1 | INTEGER | read-only | In identification number for an event. The value 1 indicates the oldest event in the file, with subsequent numbers indicating sequential events. The event text for a given number may change as a circular event log wraps over its beginning. Corresponds directly to the relative position of an event in the MANAGER EVENTS display. |
| STR eventText | 1.3.6.1.4.1.33.6.1.11.1.2 | DisplayString | read-only | The text of the event, including date, time and other information. Corresponds directly to the individual event text in the MANAGER EVENTS display. |
| INT basicDeviceNumber | 1.3.6.1.4.1.33.6.1.12 | INTEGER | read-only | The system's number of mass-storage devices. |
| deviceTable | 1.3.6.1.4.1.33.6.1.13 | not-accessible | A list of device entries. The number of entries is given by basicDeviceNumber. | |
| deviceEntry | 1.3.6.1.4.1.33.6.1.13.1 | not-accessible | Parameter values for a device entry. | |
| INT deviceIndex | 1.3.6.1.4.1.33.6.1.13.1.1 | INTEGER | read-only | In identification number for a device, in the range 1 to basicDeviceNumber |
| STR deviceName | 1.3.6.1.4.1.33.6.1.13.1.2 | DisplayString | read-only | A name by which the device is known in other displays, such as 'C1' or 'D2'. |
| STR deviceDescr | 1.3.6.1.4.1.33.6.1.13.1.3 | DisplayString | read-only | Details of the device type, including, for example, size, manufacturer, Flash versus RAM, and such. Corresponds directly to the value labeled 'Device Type: in the MANAGER DEVICE STATUS display. |
| INT deviceOperation | 1.3.6.1.4.1.33.6.1.13.1.4 | INTEGER | read-only | Current operational state of the device. Corresponds directly the value labeled 'Device Operation:' in the MANAGER DEVICE STATUS display. |
| INT deviceFormat | 1.3.6.1.4.1.33.6.1.13.1.5 | INTEGER | read-only | Formatting status of the device. Corresponds directly the presence of one of the value labels under the label 'Device Status:' in the MANAGER DEVICE STATUS display. |
| INT deviceProtection | 1.3.6.1.4.1.33.6.1.13.1.6 | INTEGER | read-only | Write-protect status of the device. Corresponds directly the presence of one of the value labels under the label 'Device Status:' in the MANAGER DEVICE STATUS display. |
| INT deviceFormatMedium | 1.3.6.1.4.1.33.6.1.13.1.7 | INTEGER | read-write | Control to cause formatting of the medium in the device. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes the device to be formatted. Corresponds directly to the FORMAT DEVICE command. |
| INT deviceGetFile | 1.3.6.1.4.1.33.6.1.13.1.8 | INTEGER | read-write | Control to cause getting a file to the device from a remote host system. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes the get to be attempted. Corresponds directly to the GET DEVICE command. When set to 'execute', the objects deviceGetFileHostIdentificationType, deviceGetFileHostIdentification, and deviceGetFileName must be somewhere in the same set request message. |
| ADR deviceGetFileHostIdentificationType | 1.3.6.1.4.1.33.6.1.13.1.9 | AddressType | read-write | The type of identification value in deviceIdentification. Corresponds indirectly to ADDRESS in the GET DEVICE command. This object may not be set outside the context of setting deviceGetFile to 'execute'. In response to a get-request or get-next-request, the value of this object is 'undefined'. |
| OCT deviceGetFileHostIdentification | 1.3.6.1.4.1.33.6.1.13.1.10 | OCTET STRING | read-write | Identification of the host to get the file from, with type depending on deviceIdentificationType. Corresponds directly to ADDRESS in the GET DEVICE command. This object may not be set outside the context of setting deviceGetFile to 'execute'. In response to a get-request or get-next-request, the value of this object is zero length. |
| STR deviceGetFileName | 1.3.6.1.4.1.33.6.1.13.1.11 | DisplayString | read-write | The name of the file to get. Corresponds directly to LOAD FILE in the GET DEVICE command. This object may not be set outside the context of setting deviceGetFile to 'execute'. In response to a get-request or get-next-request, the value of this object is zero length. |
| dump | 1.3.6.1.4.1.33.6.2 | |||
| INT dumpService | 1.3.6.1.4.1.33.6.2.1 | INTEGER | read-write | Control for allowing dump service for any client. Corresponds directly to DUMP and the value labeled 'Dump:' in the MANAGER CHARACTERISTICS display. |
| INT dumpDrive | 1.3.6.1.4.1.33.6.2.2 | INTEGER | read-write | Identification number of the disk drive where dumps are stored. Corresponds directly to DUMP DRIVE and the value labeled 'Dump Drive:' in the MANAGER CHARACTERISTICS display. |
| INT dumpMerit | 1.3.6.1.4.1.33.6.2.3 | INTEGER | read-write | Relative preference for this dump server over others. Corresponds directly to DUMP MERIT and the value labeled 'Dump Merit:' in the MANAGER CHARACTERISTICS display. |
| INT dumpSize | 1.3.6.1.4.1.33.6.2.4 | INTEGER | read-write | Type of dump file to keep. Corresponds directly to DUMP SIZE and the value labeled 'Dump Size:' in the MANAGER CHARACTERISTICS display. |
| CTR dumpCompleted | 1.3.6.1.4.1.33.6.2.5 | Counter | read-only | The number of dumps completed since system initialization. Corresponds directly to the value labeled 'Dump Operations Completed:' in the MANAGER STATUS display. |
| GAU dumpActive | 1.3.6.1.4.1.33.6.2.6 | Gauge | read-only | The number of dumps in progress. Corresponds directly to the value labeled 'Currently Dumping:' in the MANAGER STATUS display. |
| GAU dumpFileNumber | 1.3.6.1.4.1.33.6.2.7 | Gauge | read-only | The number of dump files currently stored. Corresponds directly to the value labeled 'Network dump files' and 'files' in the MANAGER FILES display. |
| dumpFileTable | 1.3.6.1.4.1.33.6.2.8 | not-accessible | A list of dump file entries. The number of entries is given by dumpFileNumber. | |
| dumpFileEntry | 1.3.6.1.4.1.33.6.2.8.1 | not-accessible | Parameter values for a dump file entry. | |
| ADR dumpFileIdentificationType | 1.3.6.1.4.1.33.6.2.8.1.1 | AddressType | read-only | The type of identification value in dumpFileIdentification. Corresponds indirectly to a file name part in the section labeled 'Network dump files' in the MANAGER FILES display. |
| OCT dumpFileIdentification | 1.3.6.1.4.1.33.6.2.8.1.2 | OCTET STRING | read-only | Identification of the dump file, an Ethernet address, as indicated by dumpFileIdentificationType. Corresponds indirectly to a file name part in the section labeled 'Network dump files' in the MANAGER FILES display. |
| INT dumpFileEntryStatus | 1.3.6.1.4.1.33.6.2.8.1.3 | INTEGER | read-write | The status of the entry. Set to 'invalid' to remove the entry, which corresponds indirectly to the PURGE MANAGER DUMP FILES command. Actual removal of the entry is implementation specific. |
| DAT dumpFileCreation | 1.3.6.1.4.1.33.6.2.8.1.4 | DateTime | read-only | The time the dump file was created. Corresponds directly to a date and time in the section labeled 'Network dump files' in the MANAGER FILES display. |
| INT dumpFileSize | 1.3.6.1.4.1.33.6.2.8.1.5 | INTEGER | read-only | The number of bytes stored in the dump file. Corresponds directly to the value labeled 'bytes' in the section labeled 'Network dump files' in the MANAGER FILES display. |
| load | 1.3.6.1.4.1.33.6.3 | |||
| INT loadService | 1.3.6.1.4.1.33.6.3.1 | INTEGER | read-write | Control for allowing load service for any client. Corresponds directly to LOAD and the value labeled 'Load:' in the MANAGER CHARACTERISTICS display. |
| INT loadMerit | 1.3.6.1.4.1.33.6.3.2 | INTEGER | read-write | Relative preference for this load server over others. Corresponds directly to LOAD MERIT and the value labeled 'Load Merit:' in the MANAGER CHARACTERISTICS display. |
| CTR loadCompleted | 1.3.6.1.4.1.33.6.3.3 | Counter | read-only | The number of loads completed since system initialization. Corresponds directly to the value labeled 'Load Operations Completed:' in the MANAGER STATUS display. |
| GAU loadActive | 1.3.6.1.4.1.33.6.3.4 | Gauge | read-only | The number of loads in progress. Corresponds directly to the value labeled 'Currently Loading:' in the MANAGER STATUS display. |
| GAU loadFileNumber | 1.3.6.1.4.1.33.6.3.5 | Gauge | read-only | The number of load files currently stored. Corresponds directly to the value labeled 'Load image files' and 'files' in the MANAGER FILES display. |
| loadFileTable | 1.3.6.1.4.1.33.6.3.6 | not-accessible | A list of load file entries. The number of entries is given by loadFileNumber. | |
| loadFileEntry | 1.3.6.1.4.1.33.6.3.6.1 | not-accessible | Parameter values for a load file entry. | |
| STR loadFileName | 1.3.6.1.4.1.33.6.3.6.1.1 | DisplayString | read-only | The name of a load file. Corresponds directly to a file name part in the section labeled 'Load image files' in the MANAGER FILES display. |
| DAT loadFileCreation | 1.3.6.1.4.1.33.6.3.6.1.2 | DateTime | read-only | The time the load file was created. Corresponds directly to a date and time in the section labeled 'Load image files' in the MANAGER FILES display. |
| INT loadFileSize | 1.3.6.1.4.1.33.6.3.6.1.3 | INTEGER | read-only | The number of bytes stored in the load file. Corresponds directly to the value labeled 'bytes' in the section labeled 'Load image files' in the MANAGER FILES display. |
| INT loadFileSoftwareVersionType | 1.3.6.1.4.1.33.6.3.6.1.4 | INTEGER | read-only | The software version type of the image in the load file. Corresponds directly to a software version in the section labeled 'Load image files' in the MANAGER FILES display. alpha 'A': alpha test beta 'B': beta test production null: normal, production software special 'S': special, custom software |
| OCT loadFileSoftwareVersion | 1.3.6.1.4.1.33.6.3.6.1.5 | OCTET STRING | read-only | The software version of the image in the load file. Corresponds directly to a software version in the section labeled 'Load image files' in the MANAGER FILES display. For example, the version display for loadFileSoftwareVersionType 'production' and loadFileSoftwareVersion '2.2.0.0' is 'V2.2'. The version display for loadFileSoftwareVersionType 'beta' and loadFileSoftwareVersion '3.1.0.4' is 'V3.1B4'. |
| param | 1.3.6.1.4.1.33.6.4 | |||
| INT paramService | 1.3.6.1.4.1.33.6.4.1 | INTEGER | read-write | Control for allowing parameter storage service for any client. Corresponds directly to PARAMETER SERVICE and the value labeled 'Parameter Service:' in the MANAGER CHARACTERISTICS display. |
| INT paramDefaultService | 1.3.6.1.4.1.33.6.4.2 | INTEGER | read-write | Control for allowing default parameter loading service for any client. Corresponds directly to PARAMETER DEFAULT SERVICE and the value labeled 'Parameter Default Service:' in the MANAGER CHARACTERISTICS display. |
| INT paramDrive | 1.3.6.1.4.1.33.6.4.3 | INTEGER | read-write | Identification number of the disk drive where parameters are stored. Corresponds directly to PARAMETER DRIVE and the value labeled 'Parameter Drive:' in the MANAGER CHARACTERISTICS display. |
| GAU paramActive | 1.3.6.1.4.1.33.6.4.4 | Gauge | read-only | The number of params in progress. Corresponds directly to the value labeled 'Currently Paraming:' in the MANAGER STATUS display. |
| GAU paramStorageActive | 1.3.6.1.4.1.33.6.4.5 | Gauge | read-only | The number of parameter storage operations in progress. Corresponds directly to the value labeled 'Currently saving parameters:' in the MANAGER STATUS display. |
| GAU paramFileNumber | 1.3.6.1.4.1.33.6.4.6 | Gauge | read-only | The number of parameter files currently stored. Corresponds directly to the value labeled 'Parameter files' and 'files' in the MANAGER FILES display. |
| paramFileTable | 1.3.6.1.4.1.33.6.4.7 | not-accessible | A list of param file entries. The number of entries is given by paramFileNumber. | |
| paramFileEntry | 1.3.6.1.4.1.33.6.4.7.1 | not-accessible | Parameter values for a param file entry. | |
| ADR paramFileIdentificationType | 1.3.6.1.4.1.33.6.4.7.1.1 | AddressType | read-only | The type of identification value in paramFileIdentification. Corresponds indirectly to a file name part in the section labeled 'Parameter files' in the MANAGER FILES display. |
| OCT paramFileIdentification | 1.3.6.1.4.1.33.6.4.7.1.2 | OCTET STRING | read-only | Identification of the param file, an Ethernet address, as indicated by paramFileIdentificationType. Corresponds indirectly to a file name part in the section labeled 'Parameter files' in the MANAGER FILES display. |
| INT paramFileEntryStatus | 1.3.6.1.4.1.33.6.4.7.1.3 | INTEGER | read-write | The status of the entry. Set to 'invalid' to remove the entry, which corresponds indirectly to the PURGE MANAGER PARAMETER FILES command. Actual removal of the entry is implementation specific. |
| DAT paramFileWrite | 1.3.6.1.4.1.33.6.4.7.1.4 | DateTime | read-only | The time the parameter file was last written. Corresponds directly to a date and time in the section labeled 'Parameter files' in the MANAGER FILES display. |
| INT paramFileSize | 1.3.6.1.4.1.33.6.4.7.1.5 | INTEGER | read-only | The number of bytes stored in the param file. Corresponds directly to the value labeled 'bytes' in the section labeled 'Parameter files' in the MANAGER FILES display. |
| INT paramFileParameterVersion | 1.3.6.1.4.1.33.6.4.7.1.6 | INTEGER | read-only | The version number of the parameter data in the file. Corresponds directly to the value labeled 'ver' in the section labeled 'Parameter files' in the MANAGER FILES display. |
| paramClient | 1.3.6.1.4.1.33.7 | |||
| STR paramClientLoaderName | 1.3.6.1.4.1.33.7.1 | DisplayString | read-only | The name of the system that most recently provided this system's stored parameters. Corresponds directly to the name value labeled 'Loaded From:' in the PARAMETER SERVER display. |
| ADR paramClientLoaderAddressType | 1.3.6.1.4.1.33.7.2 | AddressType | read-only | The type of network address contained in paramClientLoaderAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'local' means there is no address and parameters were loaded from local storage. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. Corresponds indirectly to the address value labeled 'Loaded From:' in the PARAMETER SERVER display. |
| OCT paramClientLoaderAddress | 1.3.6.1.4.1.33.7.3 | OCTET STRING | read-only | The network address of the system that most recently provided this system's stored parameters. Corresponds directly to the address value labeled 'Loaded From:' in the PARAMETER SERVER display. |
| INT paramClientParameterVersion | 1.3.6.1.4.1.33.7.4 | INTEGER | read-write | The version number of the parameters as stored in this system's local memory. Corresponds directly to SERVER PARAMETER VERSION and the value labeled 'Last Update Version:' in the PARAMETER SERVER display. |
| DAT paramClientUpdateTime | 1.3.6.1.4.1.33.7.5 | DateTime | read-only | This system's local date and time when it last attempted to store parameters with a parameter server. Corresponds directly to the values labeled 'Last Update Date:' and 'Last Update Time:' in the PARAMETER SERVER display. |
| INT paramClientServerCheck | 1.3.6.1.4.1.33.7.6 | INTEGER | read-write | Control over whether or not this system is allowed to check for additional parameter servers. 'enabled' allows checking. Corresponds directly to PARAMETER SERVER CHECK and the presence of PARAMETER POLLING under the label 'Enabled Characteristics' in the SERVER CHARACTERISTICS display. |
| INT paramClientCheckInterval | 1.3.6.1.4.1.33.7.7 | INTEGER | read-write | The number of minutes between checks for additional parameter servers. Corresponds directly to PARAMETER SERVER CHECK TIMER and the value labeled 'Check Timer:' in the PARAMETER SERVER display. |
| INT paramClientCheckNow | 1.3.6.1.4.1.33.7.8 | INTEGER | read-write | Control to cause this system to immediately check for additional parameter servers. The agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes a check to be started. Corresponds to the CHECK PARAMETER SERVER command. |
| INT paramClientServerLimit | 1.3.6.1.4.1.33.7.9 | INTEGER | read-write | The maximum number of parameter servers this system is allowed to remember at the same time. Corresponds directly to PARAMETER SERVER LIMIT and the value labeled 'Parameter Server Limit:' in the PARAMETER SERVER display. |
| INT paramClientRetransmitInterval | 1.3.6.1.4.1.33.7.10 | INTEGER | read-write | The number of minutes between this system's attempts to store new parameters with a server that has not acknowledged previous attempts. Corresponds directly to PARAMETER SERVER RETRANSMIT TIMER and the value labeled 'Retransmit Timer: in the PARAMETER SERVER display. |
| INT paramClientRetransmitLimit | 1.3.6.1.4.1.33.7.11 | INTEGER | read-write | The maximum number of attempts by this system to store new parameters with a server that has not acknowledged previous attempts. Corresponds directly to PARAMETER SERVER RETRANSMIT LIMIT and the value labeled 'Retransmit Limit:' in the PARAMETER SERVER display. |
| INT paramClientState | 1.3.6.1.4.1.33.7.12 | INTEGER | read-only | This system's state with regard to update attempts. The value meanings are: other none of the following idle no update in progress internal internal state of no meaning to manager hold holding to keep from updating too often retry waiting to retry after failure Corresponds directly to the value labeled 'Storage State:' in the PARAMETER SERVER display. |
| CTR paramClientProtocolErrors | 1.3.6.1.4.1.33.7.13 | Counter | read-only | The number of invalid parameter service protocol messages received by this system. Corresponds directly to the value labeled 'Bad Parameter Messages:' in the PARAMETER SERVER display. |
| CTR paramClientServerRejects | 1.3.6.1.4.1.33.7.14 | Counter | read-only | The number of parameter servers this system rejected due to exceeding paramClientServerLimit. Corresponds directly to the value labeled 'Rejected Servers:' in the PARAMETER SERVER display. |
| INT paramClientServerNumber | 1.3.6.1.4.1.33.7.15 | INTEGER | read-only | The number of parameter servers known to this system, indicating the number of entries in serverTable. Corresponds directly to the value labeled 'Parameter Servers:' in the PARAMETER SERVER display. |
| paramServerTable | 1.3.6.1.4.1.33.7.16 | not-accessible | A list of parameter server entries. The number of entries is given by the value of paramClientServerNumber. | |
| paramServerEntry | 1.3.6.1.4.1.33.7.16.1 | not-accessible | Status and parameter values for a parameter server. | |
| STR paramServerName | 1.3.6.1.4.1.33.7.16.1.1 | DisplayString | read-write | The server's name, unique within this system. Always 16 characters, null padded on the end. Corresponds directly to the name used to create the entry and the value labeled 'Name' in the PARAMETER SERVER display. |
| INT paramServerEntryStatus | 1.3.6.1.4.1.33.7.16.1.2 | INTEGER | read-write | The status of the entry. Set to 'invalid' to remove the entry, which corresponds directly to the CLEAR/PURGE PARAMETER SERVER command. Actual removal of the entry is implementation specific. |
| ADR paramServerAddressType | 1.3.6.1.4.1.33.7.16.1.3 | AddressType | read-write | The type of network address contained in paramServerAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'local' means there is no address and parameters were loaded from local storage. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. Corresponds indirectly to the value labeled 'Address' in the PARAMETER SERVER display. |
| OCT paramServerAddress | 1.3.6.1.4.1.33.7.16.1.4 | OCTET STRING | read-write | The server's network address. Corresponds directly to the value labeled 'Address' in the PARAMETER SERVER display. |
| INT paramServerStoredVersion | 1.3.6.1.4.1.33.7.16.1.5 | INTEGER | read-only | Parameter version number currently stored at the server. Corresponds directly to the value labeled 'Version' in the PARAMETER SERVER display. |
| DAT paramServerStoredTime | 1.3.6.1.4.1.33.7.16.1.6 | DateTime | read-only | The server's date and time when it stored the parameters of version paramServerStoredVersion. Corresponds directly to the value labeled 'Date' in the PARAMETER SERVER display. |
| INT paramServerStoredStatus | 1.3.6.1.4.1.33.7.16.1.7 | INTEGER | read-only | Status of this system's parameters with respect to the server. Corresponds directly to the value labeled 'Status' in the PARAMETER SERVER display. The value meanings are: ahead server version newer than system's behind server version older than system's current up to date failed system no longer attempting update failing system trying to update but failing query attempting to determine version unknown version not known |
| INT paramServerStoredFailure | 1.3.6.1.4.1.33.7.16.1.8 | INTEGER | read-only | When paramServerStoredStatus is 'failed' or 'failing', the reason for the most recent failure. Corresponds directly to the value labeled 'Reason' in the PARAMETER SERVER display. The value meanings are: other none of the following none no failure protocolOut invalid protocol message to server open file open error at server read file read error at server write file write error at server resource resource lack at server (e.g. disk) protocolIn invalid protocol message from server response no response from server close file close error at server delete file delete error at server rename file rename error at server fileData bad parameter data stored at server |
| xInternet | 1.3.6.1.4.1.33.10 | |||
| xIp | 1.3.6.1.4.1.33.10.1 | |||
| IP ipGatewayAddress1 | 1.3.6.1.4.1.33.10.1.1 | IpAddress | read-write | The internet address of the system's primary (first choice) gateway. A value of 0.0.0.0 indicates no address. Corresponds directly to SERVER INTERNET PRIMARY GATEWAY ADDRESS and the value labeled 'Primary Gateway Address:' in the SERVER INTERNET CHARACTERISTICS display. |
| IP ipGatewayAddress2 | 1.3.6.1.4.1.33.10.1.2 | IpAddress | read-write | The internet address of the system's secondary (second choice) gateway. A value of 0.0.0.0 indicates no address. Corresponds directly to SERVER INTERNET SECONDARY GATEWAY ADDRESS and the value labeled 'Secondary Gateway Address:' in the SERVER INTERNET CHARACTERISTICS display. |
| INT ipAutoSubnetMask | 1.3.6.1.4.1.33.10.1.3 | INTEGER | read-write | A control for automatic determination of subnet mask. 'disabled' indicates the system must use the mask as configured by the network manager. 'enabled' indicates that the system is to automatically change the subnet mask when the system's Internet address is changed. Corresponds directly to SERVER INTERNET SUBNET MASK AUTOCONFIGURE and the value labeled 'Subnet Mask Autoconfigure:' in the SERVER INTERNET CHARACTERISTICS display. |
| INT ipReassembly | 1.3.6.1.4.1.33.10.1.4 | INTEGER | read-write | A control for reassembly of IP fragments. Corresponds directly to SERVER INTERNET REASSEMBLY and the value labeled 'Reassembly:' in the SERVER INTERNET CHARACTERISTICS display. |
| xTcp | 1.3.6.1.4.1.33.10.2 | |||
| tcpPortTable | 1.3.6.1.4.1.33.10.2.1 | not-accessible | A list of TCP character port entries. | |
| tcpPortEntry | 1.3.6.1.4.1.33.10.2.1.1 | not-accessible | TCP parameter values for a character port. | |
| INT tcpPortIndex | 1.3.6.1.4.1.33.10.2.1.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Proposed Standard Internet Character MIB. |
| INT tcpPortConnectByAddress | 1.3.6.1.4.1.33.10.2.1.1.2 | INTEGER | read-write | A control for requesting outgoing connection by internet address. 'disabled' indicates outgoing connections must be by Domain name. 'enabled' indicates that outgoing connections may be requested by internet address. Corresponds directly to PORT INTERNET CONNECTIONS and the presence of the label 'Internet Connections' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT tcpPortWindowSize | 1.3.6.1.4.1.33.10.2.1.1.3 | INTEGER | read-write | Size of the TCP window for TCP connections on the port. Corresponds directly to PORT INTERNET TCP WINDOW SIZE and the value labeled 'TCP Window Size:' in the PORT ALTERNATE CHARACTERISTICS display. |
| snmpAgent | 1.3.6.1.4.1.33.10.3 | |||
| STR snmpAgentGetCommunity | 1.3.6.1.4.1.33.10.3.1 | DisplayString | read-write | The SNMP community name allowed to perform get-requests or get-next requests to this agent. Use of this value is case-insensitive. If the size is 0, the agent does not check the community name for these operations. Corresponds directly to SERVER INTERNET SNMP GET COMMUNITY and the value labeled 'Get Community:' in the SERVER INTERNET SNMP CHARACTERISTICS display. |
| STR snmpAgentSetCommunity | 1.3.6.1.4.1.33.10.3.2 | DisplayString | read-write | The SNMP community name allowed to perform set-requests to this agent. Use of this value is case-insensitive. If the size is 0, the agent does not check the community name for these operations. Corresponds directly to SERVER INTERNET SNMP SET COMMUNITY and the value labeled 'Set Community:' in the SERVER INTERNET SNMP CHARACTERISTICS display. |
| STR snmpAgentTrapCommunity | 1.3.6.1.4.1.33.10.3.3 | DisplayString | read-write | The SNMP community name sent in traps from this agent. Use of this value preserves case. Corresponds directly to SERVER INTERNET SNMP TRAP COMMUNITY and the value labeled 'Trap Community:' in the SERVER INTERNET SNMP CHARACTERISTICS display. |
| INT snmpAgentGetClientNumber | 1.3.6.1.4.1.33.10.3.4 | INTEGER | read-only | The number of client source addresses allowed to perform get-requests or get-next requests to this agent. If the value is 0, the agent does not check source address for these operations. Corresponds indirectly to the values labeled 'Get Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display. |
| INT snmpAgentSetClientNumber | 1.3.6.1.4.1.33.10.3.5 | INTEGER | read-only | The number of client source addresses allowed to perform set-requests to this agent. If the value is 0, the agent does not check source address for these operations. Corresponds indirectly to the values labeled 'Set Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display. |
| INT snmpAgentTrapClientNumber | 1.3.6.1.4.1.33.10.3.6 | INTEGER | read-only | The number of client source addresses to which this agent sends traps. If the value is 0, the agent does not perform this operation. Corresponds indirectly to the values labeled 'Trap Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display. |
| getClientTable | 1.3.6.1.4.1.33.10.3.7 | not-accessible | A list of get client entries. The number of entries is given by the value of snmpAgentGetClientNumber. | |
| getClientEntry | 1.3.6.1.4.1.33.10.3.7.1 | not-accessible | Parameter values for a get client. | |
| INT getClientIndex | 1.3.6.1.4.1.33.10.3.7.1.1 | INTEGER | read-only | Identification of a get client entry. Corresponds directly to the number in the label 'Get Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display. |
| INT getClientEntryStatus | 1.3.6.1.4.1.33.10.3.7.1.2 | INTEGER | read-write | Status of this entry. Setting the value to 'invalid' invalidates the entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. |
| ADR getClientAddressType | 1.3.6.1.4.1.33.10.3.7.1.3 | AddressType | read-write | The type of network address contained in getClientAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. If getClientAddressType does not accompany getClientAddress in a set request, the default type is 'ip'. Corresponds indirectly to the address value labeled 'Get Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display. |
| OCT getClientAddress | 1.3.6.1.4.1.33.10.3.7.1.4 | OCTET STRING | read-write | The client's network address. If getClientAddressType does not accompany getClientAddress in a set request, the default type is 'ip'. Corresponds directly to the address value labeled 'Get Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display. |
| setClientTable | 1.3.6.1.4.1.33.10.3.8 | not-accessible | A list of set client entries. The number of entries is given by the value of snmpAgentSetClientNumber. | |
| setClientEntry | 1.3.6.1.4.1.33.10.3.8.1 | not-accessible | Parameter values for a set client. | |
| INT setClientIndex | 1.3.6.1.4.1.33.10.3.8.1.1 | INTEGER | read-only | Identification of a set client entry. Corresponds directly to the number in the label 'Set Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display. |
| INT setClientEntryStatus | 1.3.6.1.4.1.33.10.3.8.1.2 | INTEGER | read-write | Status of this entry. Setting the value to 'invalid' invalidates the entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. |
| ADR setClientAddressType | 1.3.6.1.4.1.33.10.3.8.1.3 | AddressType | read-write | The type of network address contained in setClientAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. If setClientAddressType does not accompany setClientAddress in a set request, the default type is 'ip'. Corresponds indirectly to the address value labeled 'Set Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display. |
| OCT setClientAddress | 1.3.6.1.4.1.33.10.3.8.1.4 | OCTET STRING | read-write | The client's network address. When setting this value, the requester must supply setClientAddressType. If setClientAddressType does not accompany setClientAddress in a set request, the default type is 'ip'. Corresponds directly to the address value labeled 'Set Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display. |
| trapClientTable | 1.3.6.1.4.1.33.10.3.9 | not-accessible | A list of trap client entries. The number of entries is given by the value of snmpAgentTrapClientNumber. | |
| trapClientEntry | 1.3.6.1.4.1.33.10.3.9.1 | not-accessible | Parameter values for a trap client. | |
| INT trapClientIndex | 1.3.6.1.4.1.33.10.3.9.1.1 | INTEGER | read-only | Identification of a trap client entry. Corresponds directly to the number in the label 'Trap Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display. |
| INT trapClientEntryStatus | 1.3.6.1.4.1.33.10.3.9.1.2 | INTEGER | read-write | Status of this entry. Setting the value to 'invalid' invalidates the entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. |
| ADR trapClientAddressType | 1.3.6.1.4.1.33.10.3.9.1.3 | AddressType | read-write | The type of network address contained in trapClientAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. If trapClientAddressType does not accompany trapClientAddress in a set request, the default type is 'ip'. Corresponds indirectly to the address value labeled 'Trap Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display. |
| OCT trapClientAddress | 1.3.6.1.4.1.33.10.3.9.1.4 | OCTET STRING | read-write | The client's network address. When setting this value, the requester must supply trapClientAddressType. If trapClientAddressType does not accompany trapClientAddress in a set request, the default type is 'ip'. Corresponds directly to the address value labeled 'Trap Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display. |
| domainResolver | 1.3.6.1.4.1.33.10.4 | |||
| STR domainResolverSuffix | 1.3.6.1.4.1.33.10.4.1 | DisplayString | read-write | A partial domain name for the server to append to the end of an incomplete domain name provided by the user. Corresponds directly to SERVER INTERNET DEFAULT DOMAIN SUFFIX and the value labeled 'Domain Suffix:' in the SERVER INTERNET CHARACTERISTICS display. |
| IP domainResolverAddress1 | 1.3.6.1.4.1.33.10.4.2 | IpAddress | read-write | The internet address of a Domain Name Server. The system can use one or two such addresses, without preference. A value of 0.0.0.0 indicates no address. Corresponds directly to SERVER INTERNET PRIMARY DOMAIN ADDRESS and the value labeled 'Primary Domain Address:' in the SERVER INTERNET CHARACTERISTICS display. |
| IP domainResolverAddress2 | 1.3.6.1.4.1.33.10.4.3 | IpAddress | read-write | The internet address of a Domain Name Server. The system can use one or two such addresses, without preference. A value of 0.0.0.0 indicates no address. Corresponds directly to SERVER INTERNET SECONDARY DOMAIN ADDRESS and the value labeled 'Secondary Domain Address:' in the SERVER INTERNET CHARACTERISTICS display. |
| INT domainResolverTtl | 1.3.6.1.4.1.33.10.4.4 | INTEGER | read-write | The number of hours to keep received Domain information. Corresponds directly to SERVER INTERNET DOMAIN TTL and the value labeled ' Domain TTL:' in the SERVER INTERNET CHARACTERISTICS display. |
| INT domainResolverNameNumber | 1.3.6.1.4.1.33.10.4.5 | INTEGER | read-only | The number of Domain name mappings in this system's name cache. |
| nameTable | 1.3.6.1.4.1.33.10.4.6 | not-accessible | A list of Domain name entries. The number of entries is given by the value of domainResolverNameNumber. | |
| nameEntry | 1.3.6.1.4.1.33.10.4.6.1 | not-accessible | Parameter values for a Domain name. | |
| STR nameName | 1.3.6.1.4.1.33.10.4.6.1.1 | DisplayString | read-only | A fully qualified domain name. Corresponds directly to the value labeled 'Domain Name' in the DOMAIN display. |
| IP nameAddress | 1.3.6.1.4.1.33.10.4.6.1.2 | IpAddress | read-write | An Internet address corresponding to the Domain name. Corresponds directly to the value labeled 'Internet Address' in the DOMAIN display. |
| INT nameStatus | 1.3.6.1.4.1.33.10.4.6.1.3 | INTEGER | read-write | The status of the entry. Set to 'invalid' to remove the entry, which corresponds directly to the PURGE DOMAIN command. Actual removal of the entry is implementation specific. |
| INT nameSource | 1.3.6.1.4.1.33.10.4.6.1.4 | INTEGER | read-only | Source of this entry. The value meanings are: local defined by manager (LOCAL) primary obtained from a primary name server secondary obtained from a secondary name server Corresponds directly to the value labeled 'Source' in the DOMAIN display. |
| INT nameTtl | 1.3.6.1.4.1.33.10.4.6.1.5 | INTEGER | read-only | The number of minutes remaining in the entry's time to live. Corresponds directly to the value labeled 'TTL' in the DOMAIN display. |
| slip | 1.3.6.1.4.1.33.10.5 | |||
| slipTable | 1.3.6.1.4.1.33.10.5.1 | not-accessible | A list of SLIP character port entries. | |
| slipEntry | 1.3.6.1.4.1.33.10.5.1.1 | not-accessible | Parameter values for a SLIP port. | |
| INT slipIndex | 1.3.6.1.4.1.33.10.5.1.1.1 | INTEGER | read-only | An index value that uniquely identifies a port that can run SLIP. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Proposed Standard Internet Character MIB. |
| INT slipState | 1.3.6.1.4.1.33.10.5.1.1.2 | INTEGER | read-write | A control indicating whether SLIP is in operation on the port. Corresponds directly to PORT INTERNET SLIP and the value labeled 'SLIP' in the PORT CHARACTERISTICS display. |
| IP slipLocalAddress | 1.3.6.1.4.1.33.10.5.1.1.3 | IpAddress | read-write | The IP address assigned to the port. Corresponds directly to PORT SLIP ADDRESS and the value labeled 'SLIP Address:' in the PORT ALTERNATE CHARACTERISTICS display. |
| IP slipRemoteAddress | 1.3.6.1.4.1.33.10.5.1.1.4 | IpAddress | read-write | The IP address of the remote system attached to the port. Corresponds directly to PORT SLIP REMOTE and the value labeled 'Remote SLIP Address:' in the PORT ALTERNATE CHARACTERISTICS display. |
| IP slipMask | 1.3.6.1.4.1.33.10.5.1.1.5 | IpAddress | read-write | The subnet mask to use for SLIP operation on the port. Corresponds directly to PORT SLIP MASK and the value labeled 'SLIP Mask:' in the PORT ALTERNATE CHARACTERISTICS display. |
| CTR slipPortPacketsReceived | 1.3.6.1.4.1.33.10.5.1.1.6 | Counter | read-only | The number of SLIP packets received from the port. Corresponds directly to the value labeled 'Serial Packets Received:' in the PORT COUNTERS display. |
| CTR slipPortPacketsSent | 1.3.6.1.4.1.33.10.5.1.1.7 | Counter | read-only | The number of SLIP packets sent to the port. Corresponds directly to the value labeled 'Serial Packets Sent:' in the PORT COUNTERS display. |
| CTR slipPortPacketsDiscarded | 1.3.6.1.4.1.33.10.5.1.1.8 | Counter | read-only | The number of SLIP packets received from the port and discarded. Corresponds directly to the value labeled 'Serial Packets Discarded:' in the PORT COUNTERS display. |
| CTR slipPortPacketLengthErrors | 1.3.6.1.4.1.33.10.5.1.1.9 | Counter | read-only | The number of SLIP packets received from the port with an incorrect number of bytes. Corresponds directly to the value labeled 'Serial Packet Length Errors:' in the PORT COUNTERS display. |
| CTR slipPortPacketChecksumErrors | 1.3.6.1.4.1.33.10.5.1.1.10 | Counter | read-only | The number of SLIP packets received from the port with an invalid checksum. Corresponds directly to the value labeled 'Serial Packet Checksum Errors:' in the PORT COUNTERS display. |
| CTR slipNetworkPacketsReceived | 1.3.6.1.4.1.33.10.5.1.1.11 | Counter | read-only | The number of SLIP packets received from the network for this port. Corresponds directly to the value labeled 'Network Packets Received:' in the PORT COUNTERS display. |
| CTR slipNetworkPacketsSent | 1.3.6.1.4.1.33.10.5.1.1.12 | Counter | read-only | The number of SLIP packets sent to the network from this port. Corresponds directly to the value labeled 'Network Packets Sent:' in the PORT COUNTERS display. |
| CTR slipNetworkPacketsDiscarded | 1.3.6.1.4.1.33.10.5.1.1.13 | Counter | read-only | The number of SLIP packets received from the network for this port and discarded. Corresponds directly to the value labeled 'Network Packets Discarded:' in the PORT COUNTERS display. |
| telnet | 1.3.6.1.4.1.33.10.6 | |||
| telnetPortTable | 1.3.6.1.4.1.33.10.6.1 | not-accessible | A list of Telnet character port entries. | |
| telnetPortEntry | 1.3.6.1.4.1.33.10.6.1.1 | not-accessible | Telnet parameter values for a character port. | |
| INT telnetPortIndex | 1.3.6.1.4.1.33.10.6.1.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Proposed Standard Internet Character MIB. |
| INT telnetPortIncomingTcpPort | 1.3.6.1.4.1.33.10.6.1.1.2 | INTEGER | read-write | The TCP port number offered for incoming connections to this character port. Corresponds directly to PORT TELNET REMOTE PORT and the value labeled 'Remote Port:' in the PORT TELNET CHARACTERISTICS display. |
| INT telnetPortOutgoingTcpPort | 1.3.6.1.4.1.33.10.6.1.1.3 | INTEGER | read-only | The TCP port number used by default for outgoing connections from this character port. Corresponds directly to PORT TELNET DEFAULT PORT and the value labeled 'Default Port:' in the PORT TELNET CHARACTERISTICS display. |
| INT telnetPortNewlineTranslation | 1.3.6.1.4.1.33.10.6.1.1.4 | INTEGER | read-write | Translation to apply to newline sequences (CR/NULL or CR/LF) received from the network, before sending the newline to the character port. The value indicates the sequence sent to the character port, with 'none' meaning no translation. Corresponds directly to PORT TELNET NEWLINE FILTERING and the value labeled 'Newline Filtering:' in the PORT TELNET CHARACTERISTICS display. |
| STR telnetPortTerminalType | 1.3.6.1.4.1.33.10.6.1.1.5 | DisplayString | read-write | The terminal type character string for Telnet negotiations. Corresponds directly to PORT TELNET TERMINALTYPE and the value labeled 'TerminalType:' in the PORT TELNET CHARACTERISTICS display. |
| INT telnetPortEorReflection | 1.3.6.1.4.1.33.10.6.1.1.6 | INTEGER | read-write | Control for end-of-record handshake. Corresponds directly to PORT TELNET EOR REFLECTION and the value labeled 'EOR Reflection:' in the PORT TELNET CHARACTERISTICS display. |
| INT telnetPortBinaryMode | 1.3.6.1.4.1.33.10.6.1.1.7 | INTEGER | read-write | Control for operation of Telnet binary mode. The value meanings are: disabled refuse binary mode negotiation (INTERACTIVE) flowControl pass all but XON and XOFF (PASTHRU) complete pass all characters (PASSALL) Corresponds directly to PORT TELNET BINARY SESSION MODE and the value labeled 'Binary Session Mode:' in the PORT TELNET CHARACTERISTICS display. |
| telnetSerialPortTable | 1.3.6.1.4.1.33.10.6.2 | not-accessible | A list of Telnet character port entries. | |
| telnetSerialPortEntry | 1.3.6.1.4.1.33.10.6.2.1 | not-accessible | Telnet parameter values for a character port. | |
| INT telnetSerialPortIndex | 1.3.6.1.4.1.33.10.6.2.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Proposed Standard Internet Character MIB. |
| INT telnetSerialPortOptionDisplay | 1.3.6.1.4.1.33.10.6.2.1.2 | INTEGER | read-write | Control for display of Telnet option negotiations. Corresponds directly to PORT TELNET OPTION DISPLAY and the value labeled 'Option Display:' in the PORT TELNET CHARACTERISTICS display. |
| INT telnetSerialPortCsiEscape | 1.3.6.1.4.1.33.10.6.2.1.3 | INTEGER | read-write | Control for translation of 8-bit escape sequences received from the character port to 7-bit equivalents before transmission to the remote partner. Corresponds directly to PORT TELNET CSI ESCAPE and the value labeled 'CSI Escape:' in the PORT TELNET CHARACTERISTICS display. |
| INT telnetSerialPortEchoMode | 1.3.6.1.4.1.33.10.6.2.1.4 | INTEGER | read-write | Control for who echoes characters that come from the character port. The value meanings are: local terminal server echoes locally remote remote system echoes Corresponds directly to PORT TELNET ECHO MODE and the value labeled 'Echo Mode:' in the PORT TELNET CHARACTERISTICS display. |
| INT telnetSerialPortNewlineMode | 1.3.6.1.4.1.33.10.6.2.1.5 | INTEGER | read-write | Translation to apply to newline (carriage return) received from the character port, before sending the newline to the remote partner. The correspondence to command keywords is 'crNull' to NULL, 'crLF' to LINEFEED, and 'verbatim' to NOTHING (that is, no translation). Corresponds directly to PORT TELNET NEWLINE and the value labeled 'Newline:' in the PORT TELNET CHARACTERISTICS display. |
| INT telnetSerialPortTransmitMode | 1.3.6.1.4.1.33.10.6.2.1.6 | INTEGER | read-write | Criterion for deciding to send to the remote partner characters received from the character port. Corresponds directly to PORT TELNET TRANSMIT and the value labeled 'Transmit:' in the PORT TELNET CHARACTERISTICS display. |
| INT telnetSerialPortTransmitCharacterTimes | 1.3.6.1.4.1.33.10.6.2.1.7 | INTEGER | read-write | Number of character times to wait before transmitting when telnetSerialPortTransmitMode value is 'timed'. Corresponds directly to PORT TELNET TRANSMIT IDLETIME and the value labeled 'Transmit: Idle Time -' in the PORT TELNET CHARACTERISTICS display. |
| INT telnetSerialPortAbortOutputCharacter | 1.3.6.1.4.1.33.10.6.2.1.8 | INTEGER | read-write | Character input from the character port to cause aborting output. The value 0 indicates no character has this effect. Corresponds directly to PORT TELNET ABORT OUTPUT and the value labeled 'Abort Output Character:' in the PORT TELNET CHARACTERISTICS display. |
| INT telnetSerialPortAttentionCharacter | 1.3.6.1.4.1.33.10.6.2.1.9 | INTEGER | read-write | Character input from the character port to cause an attention notification to the remote partner. The value 0 indicates no character has this effect. Corresponds directly to PORT TELNET ATTENTION and the value labeled 'Attention Character:' in the PORT TELNET CHARACTERISTICS display. |
| INT telnetSerialPortEraseKeyCharacter | 1.3.6.1.4.1.33.10.6.2.1.10 | INTEGER | read-write | Character input from the character port to cause erasure of the previous input character. The value 0 indicates no character has this effect. Corresponds directly to PORT TELNET ERASE CHARACTER and the value labeled 'Erase Keystroke Character:' in the PORT TELNET CHARACTERISTICS display. |
| INT telnetSerialPortEraseLineCharacter | 1.3.6.1.4.1.33.10.6.2.1.11 | INTEGER | read-write | Character input from the character port to cause erasure of the previous line of input. The value 0 indicates no character has this effect. Corresponds directly to PORT TELNET ERASE LINE and the value labeled 'Erase Line Character:' in the PORT TELNET CHARACTERISTICS display. |
| INT telnetSerialPortInterruptCharacter | 1.3.6.1.4.1.33.10.6.2.1.12 | INTEGER | read-write | Character input from the character port to cause sending an interrupt notification to the remote partner. The value 0 indicates no character has this effect. Corresponds directly to PORT TELNET INTERRUPT and the value labeled 'Interrupt Character:' in the PORT TELNET CHARACTERISTICS display. |
| INT telnetSerialPortQueryCharacter | 1.3.6.1.4.1.33.10.6.2.1.13 | INTEGER | read-write | Character input from the character port to cause sending a status query to the remote partner. The value 0 indicates no character has this effect. Corresponds directly to PORT TELNET QUERY and the value labeled 'Query Character:' in the PORT TELNET CHARACTERISTICS display. |
| INT telnetSerialPortSynchronizeCharacter | 1.3.6.1.4.1.33.10.6.2.1.14 | INTEGER | read-write | Character input from the character port to cause sending a synchronization attempt to the remote partner. The value 0 indicates no character has this effect. Corresponds directly to PORT TELNET SYNCHRONIZE and the value labeled 'Synchronize Character:' in the PORT TELNET CHARACTERISTICS display. |
| tn3270 | 1.3.6.1.4.1.33.10.7 | |||
| INT tn3270DeviceNumber | 1.3.6.1.4.1.33.10.7.1 | INTEGER | read-only | The number of entries in the tn3270 Device table. |
| INT tn3270LanguageNumber | 1.3.6.1.4.1.33.10.7.2 | INTEGER | read-only | The number of entries in the tn3270 Language table. |
| INT tn3270PortKeymapStatus | 1.3.6.1.4.1.33.10.7.3 | INTEGER | read-write | Control for individual ports to create their own keymaps. Corresponds directly to SERVER TN3270 PORT KEYMAPS and the value labeled 'Port Keymaps:' in the SERVER TN3270 display. |
| tn3270DeviceTable | 1.3.6.1.4.1.33.10.7.4 | not-accessible | A list of tn3270 terminal device entries. | |
| tn3270DeviceEntry | 1.3.6.1.4.1.33.10.7.4.1 | not-accessible | Tn3270 parameter values for a terminal device entry. | |
| STR tn3270DeviceName | 1.3.6.1.4.1.33.10.7.4.1.1 | DisplayString | read-write | The name of a generic terminal device. Corresponds directly to SERVER TN3270 DEVICE and the value labeled 'Device Name:' in the SERVER TN3270 DEVICE display. |
| INT tn3270DeviceStatus | 1.3.6.1.4.1.33.10.7.4.1.2 | INTEGER | read-write | Status of this entry. Setting the value to 'invalid' invalidates the entry, corresponding directly to the PURGE SERVER TN3270 DEVICE command. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. |
| STR tn3270DeviceType | 1.3.6.1.4.1.33.10.7.4.1.3 | DisplayString | read-write | The terminal type character string for use when tn3270DeviceTn3270Type is insufficient. Corresponds directly to SERVER TN3270 DEVICE TERMINALTYPE and the value labeled 'TerminalType:' in the SERVER TN3270 DEVICE display. |
| INT tn3270Device3278Model | 1.3.6.1.4.1.33.10.7.4.1.4 | INTEGER | read-write | The 3278 model for the device. Corresponds directly to SERVER TN3270 DEVICE TN3278Model and the value labeled 'Tn3278Model:' in the SERVER TN3270 DEVICE display. |
| INT tn3270DeviceKeyNumber | 1.3.6.1.4.1.33.10.7.4.1.5 | INTEGER | read-only | The number of Key table entries for this device. |
| INT tn3270DeviceScreenNumber | 1.3.6.1.4.1.33.10.7.4.1.6 | INTEGER | read-only | The number of Screen table entries for this device. |
| tn3270KeyTable | 1.3.6.1.4.1.33.10.7.5 | not-accessible | A list of tn3270 key entries by device. | |
| tn3270KeyEntry | 1.3.6.1.4.1.33.10.7.5.1 | not-accessible | Tn3270 parameter values for a key entry for a device. | |
| STR tn3270KeyDeviceName | 1.3.6.1.4.1.33.10.7.5.1.1 | DisplayString | read-only | The name of a generic terminal device as in tn3270DeviceName. Corresponds directly to SERVER TN3270 DEVICE and the value labeled 'Device Name:' in the SERVER TN3270 DEVICE display. |
| INT tn3270KeyName | 1.3.6.1.4.1.33.10.7.5.1.2 | INTEGER | read-only | The key name to which this entry applies. Corresponds directly to the key portion of SERVER TN3270 DEVICE KEYMAP and the value labeled '3270-key' in the 'Keymap:' section of the SERVER TN3270 DEVICE display. |
| INT tn3270KeyStatus | 1.3.6.1.4.1.33.10.7.5.1.3 | INTEGER | read-write | Status of this entry. Setting the value to 'invalid' invalidates the entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. |
| OCT tn3270KeyCharacterSequence | 1.3.6.1.4.1.33.10.7.5.1.4 | OCTET STRING | read-write | The ASCII character sequence for the key. Corresponds directly to the escape-sequence portion of SERVER TN3270 DEVICE KEYMAP and the value labeled 'KeyCode' in the 'Keymap:' section of the SERVER TN3270 DEVICE display. |
| STR tn3270KeyDescription | 1.3.6.1.4.1.33.10.7.5.1.5 | DisplayString | read-write | Descriptive text for the key. Corresponds directly to the description portion of SERVER TN3270 DEVICE KEYMAP and the value labeled 'Description' in the SERVER TN3270 DEVICE display. |
| tn3270ScreenTable | 1.3.6.1.4.1.33.10.7.6 | not-accessible | A list of tn3270 screen action entries by device. | |
| tn3270ScreenEntry | 1.3.6.1.4.1.33.10.7.6.1 | not-accessible | Tn3270 parameter values for a screen action entry for a device. | |
| STR tn3270ScreenDeviceName | 1.3.6.1.4.1.33.10.7.6.1.1 | DisplayString | read-only | The name of a generic terminal device as in tn3270DeviceName. Corresponds directly to SERVER TN3270 DEVICE and the value labeled 'Device Name:' in the SERVER TN3270 DEVICE display. |
| INT tn3270ScreenActionName | 1.3.6.1.4.1.33.10.7.6.1.2 | INTEGER | read-only | The screen action to which this entry applies. Corresponds directly to the action portion of SERVER TN3270 DEVICE SCREENMAP and the value labeled 'Terminal Function' in the 'Screenmap: section of the SERVER TN3270 DEVICE display. |
| INT tn3270ScreenStatus | 1.3.6.1.4.1.33.10.7.6.1.3 | INTEGER | read-write | Status of this entry. Setting the value to 'invalid' invalidates the entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. |
| OCT tn3270ScreenCharacterSequence | 1.3.6.1.4.1.33.10.7.6.1.4 | OCTET STRING | read-write | The ASCII character sequence for the screen action. Some actions may have a lesser length limit. Corresponds directly to the escape-sequence portion of SERVER TN3270 DEVICE SCREENMAP and the value labeled 'HexCode' in the 'Screenmap: section of the SERVER TN3270 DEVICE display. |
| tn3270LanguageTable | 1.3.6.1.4.1.33.10.7.7 | not-accessible | A list of tn3270 language entries. | |
| tn3270LanguageEntry | 1.3.6.1.4.1.33.10.7.7.1 | not-accessible | Tn3270 parameter values for a language entry. | |
| STR tn3270LanguageName | 1.3.6.1.4.1.33.10.7.7.1.1 | DisplayString | read-write | The name of language for character translation tables. Corresponds directly to SERVER TN3270 LANGUAGE and the value labeled 'Language Name:' in the SERVER LANGUAGE display. |
| INT tn3270LanguageStatus | 1.3.6.1.4.1.33.10.7.7.1.2 | INTEGER | read-write | Status of this entry. Setting the value to 'invalid' invalidates the entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. |
| eToALanguageTable | 1.3.6.1.4.1.33.10.7.8 | not-accessible | A list of language EBCDIC to ASCII conversion entries. | |
| eToALanguageEntry | 1.3.6.1.4.1.33.10.7.8.1 | not-accessible | EBCDIC to ASCII parameter values for a language entry. | |
| STR eToALanguageName | 1.3.6.1.4.1.33.10.7.8.1.1 | DisplayString | read-only | The name of language from the language table. |
| INT eToAOffset | 1.3.6.1.4.1.33.10.7.8.1.2 | INTEGER | read-only | EBCDIC character offset plus one, that is, the value 1 corresponds to an operational offset of 0. Corresponds directly to the offset portion of SERVER TN3270 LANGUAGE and the hexadecimal labels around the conversion table labeled 'EBCDIC to ASCII' in the SERVER LANGUAGE display. |
| INT eToAValue | 1.3.6.1.4.1.33.10.7.8.1.3 | INTEGER | read-write | ASCII character value for the EBCDIC offset. Corresponds directly to the value portion of SERVER TN3270 LANGUAGE and the values in the conversion table labeled 'EBCDIC to ASCII' in the SERVER LANGUAGE display. |
| aToELanguageTable | 1.3.6.1.4.1.33.10.7.9 | not-accessible | A list of language ASCII to EBCDIC conversion entries. | |
| aToELanguageEntry | 1.3.6.1.4.1.33.10.7.9.1 | not-accessible | ASCII to EBCDIC parameter values for a language entry. | |
| STR aToELanguageName | 1.3.6.1.4.1.33.10.7.9.1.1 | DisplayString | read-only | The name of language from the language table. |
| INT aToEOffset | 1.3.6.1.4.1.33.10.7.9.1.2 | INTEGER | read-only | ASCII character offset plus one, that is, the value 1 corresponds to an operational offset of 0. Corresponds directly to the offset portion of SERVER TN3270 LANGUAGE and the hexadecimal labels around the conversion table labeled 'ASCII to EBCDIC' in the SERVER LANGUAGE display. |
| INT aToEValue | 1.3.6.1.4.1.33.10.7.9.1.3 | INTEGER | read-write | EBCDIC character value for the ASCII offset. Corresponds directly to the value portion of SERVER TN3270 LANGUAGE and the values in the conversion table labeled 'ASCII to EBCDIC' in the SERVER LANGUAGE display. |
| tn3270PortTable | 1.3.6.1.4.1.33.10.7.10 | not-accessible | A list of tn3270 character port entries. | |
| tn3270PortEntry | 1.3.6.1.4.1.33.10.7.10.1 | not-accessible | Parameter values for a tn3270 port. | |
| INT tn3270PortIndex | 1.3.6.1.4.1.33.10.7.10.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Character MIB [11]. |
| STR tn3270PortDeviceName | 1.3.6.1.4.1.33.10.7.10.1.2 | DisplayString | read-write | The name of a generic terminal device from the tn3270 device table. Corresponds directly to PORT TELNET TN3270 DEVICE and the value labeled 'Tn3270 Device:' in the PORT TELNET display. |
| STR tn3270PortLanguageName | 1.3.6.1.4.1.33.10.7.10.1.3 | DisplayString | read-write | The name of language from the tn3270 language table. Corresponds directly to PORT TELNET TN3270 LANGUAGE and the value labeled 'Tn3270 Language:' in the PORT TELNET display. |
| INT tn3270PortExtendedAttributes | 1.3.6.1.4.1.33.10.7.10.1.4 | INTEGER | read-write | A control indicating that certain 3270 extended attributes are supported on the port. Corresponds directly to PORT TELNET TN3270 XTDATTRS and the label 'Tn3270 XtdAttrs' following the label 'Enabled Characteristics' in the PORT TELNET display. |
| INT tn3270PortEorNegotiation | 1.3.6.1.4.1.33.10.7.10.1.5 | INTEGER | read-write | A control for negotiation of the Telnet EOR option when establishing a tn3270 session on the port. Corresponds directly to PORT TELNET TN3270 EOR and the label 'Tn3270 EOR' following the label 'Enabled Characteristics' in the PORT TELNET display. |
| INT tn3270PortErrorLock | 1.3.6.1.4.1.33.10.7.10.1.6 | INTEGER | read-write | A control for requiring use the RESET key when the host reports an error during a tn3270 session on the port. Corresponds directly to PORT TELNET TN3270 ERRORLOCK and the label 'Tn3270 ErrorLock' following the label 'Enabled Characteristics' in the PORT TELNET display. |
| kerberos | 1.3.6.1.4.1.33.10.8 | |||
| INT kerbStatus | 1.3.6.1.4.1.33.10.8.1 | INTEGER | read-write | A control indicating the level of Kerberos operation on the system. Corresponds directly to SERVER KERBEROS STATUS and the value labeled 'Kerberos Security:' in the SERVER KERBEROS display. |
| STR kerbRealm | 1.3.6.1.4.1.33.10.8.2 | DisplayString | read-write | The Kerberos realm with which the kerbServerName1 and kerbServerName2 are associated. Corresponds directly to SERVER KERBEROS REALM and the value labeled 'Kerberos Realm:' in the SERVER KERBEROS display. |
| INT kerbQueryLimit | 1.3.6.1.4.1.33.10.8.3 | INTEGER | read-write | The maximum number of attempts the system can make when trying to verify a Kerberos ID. Corresponds directly to SERVER KERBEROS QUERY LIMIT and the value labeled 'Kerberos Query Limit:' in the SERVER KERBEROS display. |
| STR kerbMasterName | 1.3.6.1.4.1.33.10.8.4 | DisplayString | read-write | The Domain name of the Kerberos master host system, which holds the Kerberos database. Corresponds directly to SERVER KERBEROS MASTER and the value labeled 'Kerberos Master:' in the SERVER KERBEROS display. |
| STR kerbServerName1 | 1.3.6.1.4.1.33.10.8.5 | DisplayString | read-write | The Domain name of the first Kerberos server to try when the system verifys a Kerberos ID. Corresponds directly to SERVER KERBEROS PRIMARY SERVER and the value labeled 'Kerberos Primary Server:' in the SERVER KERBEROS display. |
| STR kerbServerName2 | 1.3.6.1.4.1.33.10.8.6 | DisplayString | read-write | The Domain name of the Kerberos server to try when the system verifys a Kerberos ID and cannot reach the Kerberos primary server. Corresponds directly to SERVER KERBEROS SECONDARY SERVER and the value labeled 'Kerberos Secondary Server:' in the SERVER KERBEROS display. |
| CTR kerbInsecureLogins | 1.3.6.1.4.1.33.10.8.7 | Counter | read-only | The number of user logins on ports for which Kerberos user verification is not enabled. Corresponds directly to the value labeled 'Logins without Kerberos:' in the SERVER KERBEROS display. |
| CTR kerbSecureLogins | 1.3.6.1.4.1.33.10.8.8 | Counter | read-only | The number of successful user logins on ports for which Kerberos user verification is enabled. Corresponds directly to the value labeled 'Successful Logins:' in the SERVER KERBEROS display. |
| CTR kerbSecureLoginsFailed | 1.3.6.1.4.1.33.10.8.9 | Counter | read-only | The number of verification failures due to incorrect ID or password for attempted user logins on ports for which Kerberos user verification is enabled. Corresponds directly to the value labeled 'Unsuccessful Logins:' in the SERVER KERBEROS display. |
| CTR kerbPasswordChangeFailed | 1.3.6.1.4.1.33.10.8.10 | Counter | read-only | The number of user failures to change their Kerberos password due to invalid old password or new password verification. Corresponds directly to the value labeled 'Password Change Failures:' in the SERVER KERBEROS display. |
| INT kerbError | 1.3.6.1.4.1.33.10.8.11 | INTEGER | read-only | The error number of the most recent Kerberos-related failure. Corresponds directly to the value labeled 'Last Kerberos Error:' in the SERVER KERBEROS display. For a list of error numbers and their meanings, consult relevant Xyplex or Kerberos documentation. |
| DAT kerbErrorTime | 1.3.6.1.4.1.33.10.8.12 | DateTime | read-only | The date and time that kerbError was last updated. Corresponds directly to the value labeled 'Occurred:' in the SERVER KERBEROS display. |
| CTR kerbMasterAccess | 1.3.6.1.4.1.33.10.8.13 | Counter | read-only | The number of times the system successfully accessed the Kerberos master host. Corresponds directly to the value labeled 'Attempts to access:', 'Master', and 'Successful:' in the SERVER KERBEROS display. |
| CTR kerbMasterAccessFailed | 1.3.6.1.4.1.33.10.8.14 | Counter | read-only | The number of times the system failed access to the Kerberos master host. Corresponds directly to the value labeled 'Attempts to access:', 'Master', and 'Unsuccessful:' in the SERVER KERBEROS display. |
| CTR kerbServerAccess1 | 1.3.6.1.4.1.33.10.8.15 | Counter | read-only | The number of times the system successfully accessed the Kerberos primary server. Corresponds directly to the value labeled 'Attempts to access:', 'Server1', and 'Successful:' in the SERVER KERBEROS display. |
| CTR kerbServerAccessFailed1 | 1.3.6.1.4.1.33.10.8.16 | Counter | read-only | The number of times the system failed access to the Kerberos primary server. Corresponds directly to the value labeled 'Attempts to access:', 'Server1', and 'Unsuccessful:' in the SERVER KERBEROS display. |
| CTR kerbServerAccess2 | 1.3.6.1.4.1.33.10.8.17 | Counter | read-only | The number of times the system successfully accessed the Kerberos secondary server. Corresponds directly to the value labeled 'Attempts to access:', 'Server2', and 'Successful:' in the SERVER KERBEROS display. |
| CTR kerbServerAccessFailed2 | 1.3.6.1.4.1.33.10.8.18 | Counter | read-only | The number of times the system failed access to the Kerberos secondary server. Corresponds directly to the value labeled 'Attempts to access:', 'Server2', and 'Unsuccessful:' in the SERVER KERBEROS display. |
| kerbPortTable | 1.3.6.1.4.1.33.10.8.19 | not-accessible | A list of Kerberos character port entries. | |
| kerbPortEntry | 1.3.6.1.4.1.33.10.8.19.1 | not-accessible | Parameter values for a Kerberos port. | |
| INT kerbPortIndex | 1.3.6.1.4.1.33.10.8.19.1.1 | INTEGER | read-only | An index value that uniquely identifies a port could relate to Kerberos. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Character MIB [11]. |
| INT kerbPortStatus | 1.3.6.1.4.1.33.10.8.19.1.2 | INTEGER | read-write | A control indicating the level of Kerberos operation on the port. Corresponds directly to PORT KERBEROS and the value 'Kerberos' following the label 'Enabled Characteristics' in the PORT CHARACTERISTICS display. |
| portSecurity | 1.3.6.1.4.1.33.10.9 | |||
| INT psEntryNumber | 1.3.6.1.4.1.33.10.9.1 | INTEGER | read-only | The number of security entries in this system's port security table with psEntryStatus of 'valid'. |
| INT psEntryNumberLimit | 1.3.6.1.4.1.33.10.9.2 | INTEGER | read-only | The maximum number of security entries in this system's port security table. |
| INT psEntryInvalidIndex | 1.3.6.1.4.1.33.10.9.3 | INTEGER | read-only | A value of psEntryIndex for an entry that has psEntryStatus of 'invalid'. A management station may choose this value when adding a new entry. Collisions between independent management stations simultaneously using the same number are beyond the scope of this document. |
| psPortTable | 1.3.6.1.4.1.33.10.9.4 | not-accessible | A list of port security character port entries. | |
| psPortEntry | 1.3.6.1.4.1.33.10.9.4.1 | not-accessible | Port security parameter values for a port. | |
| INT psPortIndex | 1.3.6.1.4.1.33.10.9.4.1.1 | INTEGER | read-only | An index value that uniquely identifies a port for security purposes. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Proposed Standard Internet Character MIB. |
| INT psPortDefaultInboundAccess | 1.3.6.1.4.1.33.10.9.4.1.2 | INTEGER | read-write | The default access to the port for incoming TCP connections. Corresponds directly to PORT INTERNET SECURITY DEFAULT INBOUND and the value labeled 'Inbound Default:' in the PORT INTERNET SECURITY display. |
| INT psPortDefaultOutboundAccess | 1.3.6.1.4.1.33.10.9.4.1.3 | INTEGER | read-write | The default access to the port for outgoing TCP connections. Corresponds directly to PORT INTERNET SECURITY DEFAULT OUTBOUND and the value labeled 'Outbound Default:' in the PORT INTERNET SECURITY display. |
| psTable | 1.3.6.1.4.1.33.10.9.5 | not-accessible | A list of port security entries. | |
| psEntry | 1.3.6.1.4.1.33.10.9.5.1 | not-accessible | Port security parameter values for an entry for a port. | |
| INT psEntryIndex | 1.3.6.1.4.1.33.10.9.5.1.1 | INTEGER | read-only | A small, numeric distinguisher for port security entries. When adding a new entry, the client should specify an unused value, such as psEntryInvalidIndex. Corresponds directly to the value labeled 'Entry' in the SERVER INTERNET SECURITY display. |
| INT psEntryStatus | 1.3.6.1.4.1.33.10.9.5.1.2 | INTEGER | read-write | Status of this entry. Setting the value to 'invalid' invalidates the entry, corresponding directly to the CLEAR INTERNET SECURITY command. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. When creating a new instance, psEntryAddress, psEntryMask, psEntryAccess, and psEntryDirection for the new instance must be present in the set request. |
| IP psEntryAddress | 1.3.6.1.4.1.33.10.9.5.1.3 | IpAddress | read-write | The IP address to which the entry pertains. Corresponds directly to the PORT INTERNET SECURITY internet address and the value labeled 'Internet Address' in the SERVER INTERNET SECURITY display. |
| IP psEntryMask | 1.3.6.1.4.1.33.10.9.5.1.4 | IpAddress | read-write | The mask applied to psEntryAddress when making a security check based on this entry. Corresponds directly to PORT INTERNET SECURITY MASK and the value labeled 'Security Mask' in the SERVER INTERNET SECURITY display. |
| INT psEntryAccess | 1.3.6.1.4.1.33.10.9.5.1.5 | INTEGER | read-write | The access to the port for TCP connections when making a security check based on this entry. Corresponds directly to PORT INTERNET SECURITY ALLOW or DENY and the value labeled 'Access' in the SERVER INTERNET SECURITY display. |
| INT psEntryDirection | 1.3.6.1.4.1.33.10.9.5.1.6 | INTEGER | read-write | The direction of TCP connections to which this entry applies. Corresponds directly to PORT INTERNET SECURITY INBOUND or OUTBOUND and the value labeled 'Direction' in the SERVER INTERNET SECURITY display. |
| OCT psEntryPortMap | 1.3.6.1.4.1.33.10.9.5.1.7 | OCTET STRING | read-write | The list of character ports to which this entry applies. The OCTET STRING contains a bitmap, with one bit for each port, and enough octets for all the ports on the system. Port numbers are as defined for charPortIndex in the Proposed Standard Internet Character MIB. Corresponding bit numbers start with 1 as the high-order bit of the first octet. Corresponds directly to PORT INTERNET SECURITY and the value labeled 'Ports' in the SERVER INTERNET SECURITY display. |
| xremote | 1.3.6.1.4.1.33.10.10 | |||
| STR xremoteServerName1 | 1.3.6.1.4.1.33.10.10.1 | DisplayString | read-write | The Domain name of the first XREMOTE font server to try for downloading fonts. Corresponds directly to SERVER XREMOTE PRIMARY SERVER and the value labeled 'Xremote Primary Font Server:' in the SERVER XREMOTE display. |
| STR xremoteServerName2 | 1.3.6.1.4.1.33.10.10.2 | DisplayString | read-write | The Domain name of the XREMOTE font server to try for downloading fonts and the primary font server does not respond. Corresponds directly to SERVER XREMOTE SECONDARY SERVER and the value labeled 'Xremote Secondary Font Server:' in the SERVER XREMOTE display. |
| CTR xremoteServerAccess1 | 1.3.6.1.4.1.33.10.10.3 | Counter | read-only | The number of times the system successfully accessed the XREMOTE primary font server. Corresponds directly to the value labeled 'Attempts to access:', 'Server1', and 'Successful:' in the SERVER XREMOTE display. |
| CTR xremoteServerAccessFailed1 | 1.3.6.1.4.1.33.10.10.4 | Counter | read-only | The number of times the system failed access to the XREMOTE primary font server. Corresponds directly to the value labeled 'Attempts to access:', 'Server1', and 'Unsuccessful:' in the SERVER XREMOTE display. |
| CTR xremoteServerAccess2 | 1.3.6.1.4.1.33.10.10.5 | Counter | read-only | The number of times the system successfully accessed the XREMOTE secondary font server. Corresponds directly to the value labeled 'Attempts to access:', 'Server2', and 'Successful:' in the SERVER XREMOTE display. |
| CTR xremoteServerAccessFailed2 | 1.3.6.1.4.1.33.10.10.6 | Counter | read-only | The number of times the system failed access to the XREMOTE secondary font server. Corresponds directly to the value labeled 'Attempts to access:', 'Server2', and 'Unsuccessful:' in the SERVER XREMOTE display. |
| GAU xremoteSessions | 1.3.6.1.4.1.33.10.10.7 | Gauge | read-only | The number of connected XREMOTE sessions. Corresponds directly to the value labeled 'Current Number of Xremote Sessions:' in the SERVER XREMOTE display. |
| xremotePortTable | 1.3.6.1.4.1.33.10.10.8 | not-accessible | A list of XREMOTE character port entries. | |
| xremotePortEntry | 1.3.6.1.4.1.33.10.10.8.1 | not-accessible | XREMOTE parameter values for a port. | |
| INT xremotePortIndex | 1.3.6.1.4.1.33.10.10.8.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Proposed Standard Internet Character MIB. |
| INT xremotePortXremote | 1.3.6.1.4.1.33.10.10.8.1.2 | INTEGER | read-write | Control for use of XREMOTE on the port. Corresponds directly to PORT XREMOTE and the presence of the label 'Xremote' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT xremotePortXdmQuery | 1.3.6.1.4.1.33.10.10.8.1.3 | INTEGER | read-write | The type of query message issued by a port when searching for an X Display Manager (XDM). Corresponds directly to the PORT XDM QUERY and the 'XDM Query:' in the PORT ALTERNATE CHARACTERISTICS display |
| STR xremotePortXdmHost | 1.3.6.1.4.1.33.10.10.8.1.4 | DisplayString | read-write | The Domain name or Internet address of the X Display Manager (XDM) for a port. Corresponds directly to the PORT XDM HOST and the 'XDM Host:' in the PORT ALTERNATE CHARACTERISTICS display |
| GAU xremoteServerClients | 1.3.6.1.4.1.33.10.10.9 | Gauge | read-only | The number of active X clients. Corresponds directly to the value labeled 'Current Number of XClients:' in the SERVER XREMOTE display. |
| rotary | 1.3.6.1.4.1.33.10.11 | |||
| INT rotaryNumber | 1.3.6.1.4.1.33.10.11.1 | INTEGER | read-only | The number of entries in the Rotary table. |
| rotaryTable | 1.3.6.1.4.1.33.10.11.2 | not-accessible | A list of rotary entries. | |
| rotaryEntry | 1.3.6.1.4.1.33.10.11.2.1 | not-accessible | Parameter values for a rotary. | |
| IP rotaryAddress | 1.3.6.1.4.1.33.10.11.2.1.1 | IpAddress | read-write | The internet address to be recognized as a rotary. Corresponds directly to the ip-address portion of SERVER INTERNET ROTARY and the value labeled 'Internet Address' in the SERVER INTERNET ROTARY display. |
| INT rotaryStatus | 1.3.6.1.4.1.33.10.11.2.1.2 | INTEGER | read-write | Status of this entry. Setting the value to 'invalid' invalidates the entry, corresponding directly to the CLEAR SERVER INTERNET ROTARY command. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. |
| OCT rotaryPortMap | 1.3.6.1.4.1.33.10.11.2.1.3 | OCTET STRING | read-write | The list of character ports that compose the rotary. The OCTET STRING contains a bitmap, with one bit for each port, and enough octets for all the ports on the system. Port numbers are as defined for charPortIndex in the Proposed Standard Internet Character MIB. Corresponding bit numbers start with 1 as the high-order bit of the first octet. Corresponds directly to port-list portion of SERVER INTERNET ROTARY and the value labeled 'Ports' in the SERVER INTERNET ROTARY display. |
| xEgp | 1.3.6.1.4.1.33.10.12 | |||
| ospf | 1.3.6.1.4.1.33.10.13 | |||
| routerIp | 1.3.6.1.4.1.33.10.14 | |||
| routerUdp | 1.3.6.1.4.1.33.10.15 | |||
| routerPolicy | 1.3.6.1.4.1.33.10.16 | |||
| ethernet | 1.3.6.1.4.1.33.11 | |||
| etherTable | 1.3.6.1.4.1.33.11.1 | not-accessible | A list of generic entries. | |
| etherEntry | 1.3.6.1.4.1.33.11.1.1 | not-accessible | Generic status and parameter values for an Ethernet interface. | |
| INT etherIndex | 1.3.6.1.4.1.33.11.1.1.1 | INTEGER | read-only | An index value that uniquely identifies an Ethernet interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. |
| CTR etherAlignmentErrors | 1.3.6.1.4.1.33.11.1.1.2 | Counter | read-only | A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check. |
| CTR etherFCSErrors | 1.3.6.1.4.1.33.11.1.1.3 | Counter | read-only | A count of frames received on a particular interface that are an integral number of octets in length that do not pass the FCS check. |
| etherTxTable | 1.3.6.1.4.1.33.11.2 | not-accessible | A list of Ethernet transmit entries. | |
| etherTxEntry | 1.3.6.1.4.1.33.11.2.1 | not-accessible | Transmit status and parameter values for an Ethernet interface. | |
| INT etherTxIndex | 1.3.6.1.4.1.33.11.2.1.1 | INTEGER | read-only | An index value that uniquely identifies an Ethernet interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. |
| CTR etherTxSingleCollisionFrames | 1.3.6.1.4.1.33.11.2.1.2 | Counter | read-only | A count of successfully transmitted frames on a particular interface for which transmission is inhibited by exactly one collision. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts or ifOutNUcastPkts object and is not counted by the corresponding instance of the etherTxMultipleCollisionFrames object. |
| CTR etherTxMultipleCollisionFrames | 1.3.6.1.4.1.33.11.2.1.3 | Counter | read-only | A count of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts or ifOutNUcastPkts object and is not counted by the corresponding instance of the etherTxSingleCollisionFrames object. |
| etherMulticastTable | 1.3.6.1.4.1.33.11.3 | not-accessible | A list of etherMulticast entries. | |
| etherMulticastEntry | 1.3.6.1.4.1.33.11.3.1 | not-accessible | EtherMulticast status and parameter values for an Ethernet interface. | |
| INT etherMulticastIndex | 1.3.6.1.4.1.33.11.3.1.1 | INTEGER | read-only | An index value that uniquely identifies an Ethernet interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. |
| CTR etherMulticastBytesIn | 1.3.6.1.4.1.33.11.3.1.2 | Counter | read-only | A count of frames successfully received on a particular interface and for which the destination address multicast bit was set. Bytes that are counted by an instance of this object are also counted by the corresponding instance of the ifInOctets object. |
| CTR etherMulticastBytesOut | 1.3.6.1.4.1.33.11.3.1.3 | Counter | read-only | A count of successfully frames successfully transmitted on a particular interface and for which the destination address multicast bit was set. Bytes that are counted by an instance of this object are also counted by the corresponding instance of the ifOutOctets object. |
| etherXTxTable | 1.3.6.1.4.1.33.11.4 | not-accessible | A list of Ethernet extended transmit entries. | |
| etherXTxEntry | 1.3.6.1.4.1.33.11.4.1 | not-accessible | Extended transmit status and parameter values for an Ethernet interface. | |
| INT etherXTxIndex | 1.3.6.1.4.1.33.11.4.1.1 | INTEGER | read-only | An index value that uniquely identifies an Ethernet interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. |
| CTR etherXTxExcessiveCollisions | 1.3.6.1.4.1.33.11.4.1.2 | Counter | read-only | A count of frames for which transmission on a particular interface fails due to excessive collisions. |
| bootClient | 1.3.6.1.4.1.33.12 | |||
| STR bootClientStatus | 1.3.6.1.4.1.33.12.1 | DisplayString | read-only | The overall status of the bootstrapping operation, including, for example, what is presently happening and error information. |
| character | 1.3.6.1.4.1.33.13 | |||
| basic | 1.3.6.1.4.1.33.13.1 | |||
| INT basicBroadcast | 1.3.6.1.4.1.33.13.1.1 | INTEGER | read-write | Control for user ability to broadcast messages to other local ports. Corresponds directly to SERVER BROADCAST and the presence of the label 'Broadcast' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| INT basicErrorReport | 1.3.6.1.4.1.33.13.1.2 | INTEGER | read-write | Control for server display of an error when the user gives an unsupported command. Corresponds directly to SERVER REPORT ERRORS and the presence of the label 'Report Errors' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| INT basicLock | 1.3.6.1.4.1.33.13.1.3 | INTEGER | read-write | Control for user ability to use a password to protect a logged in terminal from other users. Corresponds directly to SERVER LOCK and the presence of the label 'Lock' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| INT basicInactivityTimer | 1.3.6.1.4.1.33.13.1.4 | INTEGER | read-write | Number of minutes a terminal may remain logged in with no sessions, no input or output, and no modem transitions. Corresponds directly to SERVER INACTIVITY TIMER and the value labeled 'Inactivity Timer:' in the SERVER CHARACTERISTICS display. |
| INT basicPasswordRetryLimit | 1.3.6.1.4.1.33.13.1.5 | INTEGER | read-write | Number of times the server allows a user to retry an incorrect password. Corresponds directly to SERVER PASSWORD LIMIT and the value labeled 'Password Limit:' in the SERVER CHARACTERISTICS display. |
| STR basicPrivilegedPassword | 1.3.6.1.4.1.33.13.1.6 | DisplayString | read-write | The password a user must enter to become privileged. For security reasons, reading this object always returns a zero-length value. Corresponds directly to SERVER PRIVILEGED PASSWORD. |
| STR basicLoginPassword | 1.3.6.1.4.1.33.13.1.7 | DisplayString | read-write | The password a user must enter to be given the opportunity to log in. For security reasons, reading this object always returns a zero-length value. Corresponds directly to SERVER LOGIN PASSWORD. |
| STR basicLoginPrompt | 1.3.6.1.4.1.33.13.1.8 | DisplayString | read-write | The text string the server displays to prompt a user for the login password. Corresponds directly to SERVER LOGIN PROMPT. |
| STR basicWelcome | 1.3.6.1.4.1.33.13.1.9 | DisplayString | read-write | The text string the server displays before attempting to log in a user. Corresponds directly to SERVER WELCOME and the value labeled 'Welcome:' in the SERVER CHARACTERISTICS display. |
| GAU basicActivePorts | 1.3.6.1.4.1.33.13.1.10 | Gauge | read-only | The number of ports with connected sessions or logged in users. Corresponds directly to the value labeled 'Active Ports:' and 'Cur' in the SERVER STATUS display. |
| GAU basicActivePortsHigh | 1.3.6.1.4.1.33.13.1.11 | Gauge | read-only | The highest value of basicActivePorts since system initialization. Corresponds directly to the value labeled 'Active Ports:' and 'High' in the SERVER STATUS display. |
| GAU basicActiveUsers | 1.3.6.1.4.1.33.13.1.12 | Gauge | read-only | The number of logged in users. Corresponds directly to the value labeled 'Active Users:' and 'Cur' in the SERVER STATUS display. |
| GAU basicActiveUsersHigh | 1.3.6.1.4.1.33.13.1.13 | Gauge | read-only | The highest value of basicActiveUsers since system initialization. Corresponds directly to the value labeled 'Active Users:' and 'High' in the SERVER STATUS display. |
| GAU basicSessions | 1.3.6.1.4.1.33.13.1.14 | Gauge | read-only | The total number of connected sessions. Corresponds directly to the value labeled 'Connected Sessions:' and 'Cur' in the SERVER STATUS display. |
| GAU basicSessionsHigh | 1.3.6.1.4.1.33.13.1.15 | Gauge | read-only | The highest value of basicSessions since system initialization. Corresponds directly to the value labeled 'Connected Sessions:' and 'High' in the SERVER STATUS display. |
| INT basicSessionsLimit | 1.3.6.1.4.1.33.13.1.16 | INTEGER | read-write | The maximum total number of sessions that can simultaneously be connected to the system. A value of -1 indicates no limit up to available dynamic system memory. Corresponds directly to SERVER SESSION LIMIT and the value labeled 'Connected Sessions:' and 'Max' in the SERVER STATUS display. |
| basicPortTable | 1.3.6.1.4.1.33.13.1.17 | not-accessible | A list of basic character port entries. | |
| basicPortEntry | 1.3.6.1.4.1.33.13.1.17.1 | not-accessible | Basic parameter values for a port. | |
| INT basicPortIndex | 1.3.6.1.4.1.33.13.1.17.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Character MIB [12]. |
| INT basicPortDefaultDestAction | 1.3.6.1.4.1.33.13.1.17.1.2 | INTEGER | read-write | The action to take relative to basicPortDefaultDestName. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE and the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. |
| INT basicPortDefaultDestProtocol | 1.3.6.1.4.1.33.13.1.17.1.3 | INTEGER | read-write | The session protocol to use with basicPortDefaultDestName. Corresponds directly to LAT/TELNET PORT DEDICATED/PREFERRED SERVICE. |
| STR basicPortDefaultDestName | 1.3.6.1.4.1.33.13.1.17.1.4 | DisplayString | read-write | The default name to use in forming a connection when no other name is specified. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE and the value labeled 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. If the value of basicPortDefaultDestProtocol is 'telnet', an Internet port number may be included on the end of the name, delimited with a colon (':'). If the value of basicPortDefaultDestProtocol is not 'telnet', then the maximum length is 16. |
| STR basicPortDefaultDestLATNodeName | 1.3.6.1.4.1.33.13.1.17.1.5 | DisplayString | read-write | A LAT node name to use with basicPortDefaultDestName. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE NODE and the value labeled 'Node:' following the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. This object can have a non- zero-length value only if the value of basicPortDefaultDestProtocol is 'lat'. |
| STR basicPortDefaultDestLATPortName | 1.3.6.1.4.1.33.13.1.17.1.6 | DisplayString | read-write | A LAT port name to use with basicPortDefaultDestName. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE NODE and the value labeled 'Node:' following the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. this object can hav a non-zero-length value only if the value if basicPortDefaultDestProtocol is 'lat' |
| INT basicPortAutoConnect | 1.3.6.1.4.1.33.13.1.17.1.7 | INTEGER | read-write | Control for automatic session connection. Corresponds directly to PORT AUTOCONNECT and the presence of the label 'Autoconnect' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicPortAutoLogin | 1.3.6.1.4.1.33.13.1.17.1.8 | INTEGER | read-write | Control for automatic port login. Corresponds directly to PORT AUTODEDICATED and the presence of the label 'Autodedicated' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicPortBroadcast | 1.3.6.1.4.1.33.13.1.17.1.9 | INTEGER | read-write | Control for display of messages sent by users on other ports. Corresponds directly to PORT BROADCAST and the presence of the label 'Broadcast' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicPortConnectResume | 1.3.6.1.4.1.33.13.1.17.1.10 | INTEGER | read-write | Control for behavior of a connection attempt to a destination where the port already has a connection. 'disabled' causes a new connection. 'enabled' causes the existing connection to become the active connection. Corresponds directly to PORT CONNECTRESUME and the presence of the label 'Connectresume' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicPortDialup | 1.3.6.1.4.1.33.13.1.17.1.11 | INTEGER | read-write | Defines whether the port should be considered as connected to a dialup line. 'enabled' means that it is. Corresponds directly to PORT DIALUP and the presence of the label 'Dial Up' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicPortIdleTimeout | 1.3.6.1.4.1.33.13.1.17.1.12 | INTEGER | read-write | The number of minutes the system will allow a session to have no activity before automatically disconnecting it. A value of -1 indicates no timeout. Zero is not a valid value. Corresponds directly to PORT IDLE TIMEOUT and the value labeled 'Idle Timeout:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicPortInactivityLogout | 1.3.6.1.4.1.33.13.1.17.1.13 | INTEGER | read-write | Control for the system automatically logging the port out when it has no sessions, no local activity, and no modem signal changes for the time period specified by basicInactivityTimer. Corresponds directly to PORT INACTIVITY LOGOUT and the presence of the label 'Inactivity Logout' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicPortLossNotification | 1.3.6.1.4.1.33.13.1.17.1.14 | INTEGER | read-write | Control for the system sending a Bell character to the port when it looses an input character due to an overrun or data error. Corresponds directly to PORT LOSS NOTIFICATION and the presence of the label 'Loss Notification' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicPortMessageCodes | 1.3.6.1.4.1.33.13.1.17.1.15 | INTEGER | read-write | Control for including error numbers in error messages displayed on the port. Corresponds directly to PORT MESSAGE CODES and the presence of the label 'Message Codes' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicPortMultisessions | 1.3.6.1.4.1.33.13.1.17.1.16 | INTEGER | read-write | Control for running the multisession line protocol between the port and the locally-connected terminal. Corresponds directly to PORT MULTISESSIONS and the presence of the label 'Multisessions' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| STR basicPortDefaultUserName | 1.3.6.1.4.1.33.13.1.17.1.17 | DisplayString | read-write | Default user name to use for automatically logging in the port. Corresponds directly to PORT USERNAME and the value labeled 'Port n:' in the PORT CHARACTERISTICS display. |
| INT basicPortVerification | 1.3.6.1.4.1.33.13.1.17.1.18 | INTEGER | read-write | Control for display of informational messages on the port when the user connects, disconnects, or switches a session. Corresponds directly to PORT VERIFICATION and the presence of the label 'Verification' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicPortDefaultProtocol | 1.3.6.1.4.1.33.13.1.17.1.19 | INTEGER | read-write | The session protocol to use when not otherwise specified. Corresponds directly to PORT RESOLVE SERVICE and the value labeled 'Resolve Service:' in the PORT ALTERNATE CHARACTERISTICS display. |
| CTR basicPortLogins | 1.3.6.1.4.1.33.13.1.17.1.20 | Counter | read-only | The number of logins on the port since system initialization. Corresponds directly to the value labeled 'Local Accesses:' in the PORT COUNTERS display. |
| CTR basicPortRemoteSessions | 1.3.6.1.4.1.33.13.1.17.1.21 | Counter | read-only | The number of remotely originating sessions to the port since system initialization. Corresponds directly to the value labeled 'Remote Accesses:' in the PORT COUNTERS display. |
| CTR basicPortIdleTimeouts | 1.3.6.1.4.1.33.13.1.17.1.22 | Counter | read-only | The number of session disconnects due to expiration of basicPortIdleTimeout. Corresponds directly to the value labeled 'Idle Timeouts:' in the PORT COUNTERS display. |
| INT basicPortStatus | 1.3.6.1.4.1.33.13.1.17.1.23 | INTEGER | read-only | The current operational status of the port. Corresponds directly to the value labeled 'Status:' in the PORT STATUS display. |
| INT basicPortLastInCharacter | 1.3.6.1.4.1.33.13.1.17.1.24 | INTEGER | read-only | The character that most recently came into the port. Corresponds directly to the value labeled 'Last Char Input:' in the PORT STATUS display. |
| INT basicPortLastOutCharacter | 1.3.6.1.4.1.33.13.1.17.1.25 | INTEGER | read-only | The character that most recently went out of the port. Corresponds directly to the value labeled 'Last Char Output:' in the PORT STATUS display. |
| STR basicPortActiveUserName | 1.3.6.1.4.1.33.13.1.17.1.26 | DisplayString | read-only | The user name currently logged into the port. Corresponds directly to the value by the port number and labeled 'Username' in the USERS display. |
| INT basicPortDefaultSessionMode | 1.3.6.1.4.1.33.13.1.17.1.27 | INTEGER | read-write | Data recognition mode when starting a session, with the following meanings: interactive locally recognize all controls binary recognize only session protocol (corresponds to PASSALL) binaryWithFlow recognize only XON and XOFF (corresponds to PASTHRU transparent recognize no data Corresponds directly to PORT DEFAULT SESSION MODE and the value labeled 'Default Session Mode:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicPortZero | 1.3.6.1.4.1.33.13.1.17.1.28 | INTEGER | read-write | Control to zero counters for the port. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes the port's counters to be zeroed. Corresponds to the ZERO PORT command. |
| TIK basicPortZeroTime | 1.3.6.1.4.1.33.13.1.17.1.29 | TimeTicks | read-only | The number of hundredths of a second since the most recent zeroing of the port's counters, such as through execution of basicPortZero. Corresponds directly to the value labeled 'Seconds Since Zeroed:' in the PORT COUNTERS display. |
| basicSerialPortTable | 1.3.6.1.4.1.33.13.1.18 | not-accessible | A list of basic character serial port entries. | |
| basicSerialPortEntry | 1.3.6.1.4.1.33.13.1.18.1 | not-accessible | Basic parameter values for a serial port. | |
| INT basicSerialPortIndex | 1.3.6.1.4.1.33.13.1.18.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Character MIB [12]. |
| INT basicSerialPortBreak | 1.3.6.1.4.1.33.13.1.18.1.2 | INTEGER | read-write | Action to take on a BREAK condition from the port. Corresponds directly to PORT BREAK and the value labeled 'Break:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortInterrupts | 1.3.6.1.4.1.33.13.1.18.1.3 | INTEGER | read-write | Control for recognizing BREAK or local switch to interrupt a session. Corresponds directly to PORT INTERRUPTS and the presence of the label 'Interrupts' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortNoLoss | 1.3.6.1.4.1.33.13.1.18.1.4 | INTEGER | read-write | Control for storing port input locally in anticipation of session startup. Corresponds directly to PORT NOLOSS and the presence of the label 'Noloss' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortPause | 1.3.6.1.4.1.33.13.1.18.1.5 | INTEGER | read-write | Control for pausing after each screenful of locally-originated output to the port. Corresponds directly to PORT PAUSE and the presence of the label 'Pause' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| STR basicSerialPortPrompt | 1.3.6.1.4.1.33.13.1.18.1.6 | DisplayString | read-write | Prompt for the system to use on the port. Corresponds directly to PORT PROMPT and the value labeled 'Prompt:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortTerminalType | 1.3.6.1.4.1.33.13.1.18.1.7 | INTEGER | read-write | Type of terminal attached to the port, for formatting local output. Corresponds directly to PORT TYPE and the value labeled 'Type:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortTypeaheadLimit | 1.3.6.1.4.1.33.13.1.18.1.8 | INTEGER | read-write | Maximum number of input characters to hold pending tranmission on a session. Corresponds directly to PORT TYPEAHEAD SIZE and the value labeled 'Typeahead Size:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortBackwardSwitch | 1.3.6.1.4.1.33.13.1.18.1.9 | INTEGER | read-write | Character input from the character port to cause a switch to the previous, lower numbered session. The value 0 indicates no character has this effect. Corresponds directly to PORT BACKWARD SWITCH and the value labeled 'Backwards Switch:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortForwardSwitch | 1.3.6.1.4.1.33.13.1.18.1.10 | INTEGER | read-write | Character input from the character port to cause a switch to the next, higher numbered session. The value 0 indicates no character has this effect. Corresponds directly to PORT FORWARD SWITCH and the value labeled 'Forwards Switch:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortLocalSwitch | 1.3.6.1.4.1.33.13.1.18.1.11 | INTEGER | read-write | Character input from the character port to cause a switch to local command mode. The value 0 indicates no character has this effect. Corresponds directly to PORT LOCAL SWITCH and the value labeled 'Local Switch:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortModemControl | 1.3.6.1.4.1.33.13.1.18.1.12 | INTEGER | read-write | Control for observing hardware modem control signals. Corresponds directly to PORT MODEM CONTROL and the value labeled 'Modem Control:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortSignalCheck | 1.3.6.1.4.1.33.13.1.18.1.13 | INTEGER | read-write | Control for observing DSR and DCD to bound allowing sessions. Corresponds directly to PORT SIGNAL CHECK and the presence of the label 'Signal Check' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortDSRLogout | 1.3.6.1.4.1.33.13.1.18.1.14 | INTEGER | read-write | Control for logging out the port when DCD is deasserted. Corresponds directly to PORT DSRLOGOUT and the presence of the label 'DSRlogout' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortDSRObserve | 1.3.6.1.4.1.33.13.1.18.1.15 | INTEGER | read-write | Control for beginning the login sequence on the port when DCD is asserted. Corresponds directly to PORT DSRWAIT and the presence of the label 'DSRwait' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortDCDTimeout | 1.3.6.1.4.1.33.13.1.18.1.16 | INTEGER | read-write | The number of milleseconds that DCD may be asserted before disconnecting the port. Corresponds directly to PORT DCD TIMEOUT and the value labeled 'DCD Timeout:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortDTRAssert | 1.3.6.1.4.1.33.13.1.18.1.17 | INTEGER | read-write | Control when the system asserts DTR on the port. always unconditional(DISABLED) onConnectionOrRing connection formed or RING asserted(ENABLED) onConnection connection formed (FORCONNECTION) onRing RING asserted (FORRING) Corresponds directly to PORT DTRWAIT and the value labeled 'DTR Wait:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLimitedCommands | 1.3.6.1.4.1.33.13.1.18.1.18 | INTEGER | read-write | Control for limiting the commands available to the user on the port. Corresponds directly to PORT SECURITY and the presence of the label 'Security' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortLimitedView | 1.3.6.1.4.1.33.13.1.18.1.19 | INTEGER | read-write | Control for restricting what a user may display. Corresponds directly to PORT LIMITED VIEW and the presence of the label 'Limited View' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortPassword | 1.3.6.1.4.1.33.13.1.18.1.20 | INTEGER | read-write | Control for requiring the user to supply the login password to log in on the port. Corresponds directly to PORT PASSWORD and the presence of the label 'Password' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortLineEditor | 1.3.6.1.4.1.33.13.1.18.1.21 | INTEGER | read-write | Control for allowing the user to use local mode command line editing. Corresponds directly to PORT LINE EDITOR and the presence of the label 'Line Editor' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT basicSerialPortLineEditorBackspace | 1.3.6.1.4.1.33.13.1.18.1.22 | INTEGER | read-write | Character input from the character port to move the cursor to the left. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR BACKSPACE and the value labeled 'Backspace Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorBeginning | 1.3.6.1.4.1.33.13.1.18.1.23 | INTEGER | read-write | Character input from the character port to move the cursor to the beginning of the line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR BEGINNING and the value labeled 'Begin Line Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorCancel | 1.3.6.1.4.1.33.13.1.18.1.24 | INTEGER | read-write | Character input from the character port to cancel an interactive dialog or delete the current line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR CANCEL and the value labeled 'Cancel Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorDeleteBeginning | 1.3.6.1.4.1.33.13.1.18.1.25 | INTEGER | read-write | Character input from the character port to delete the current line from the cursor to the beginning. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR DELETE BEGINNING and the value labeled 'Delete Begin Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorDeleteLine | 1.3.6.1.4.1.33.13.1.18.1.26 | INTEGER | read-write | Character input from the character port to delete the current line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR DELETE LINE and the value labeled 'Delete Line Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorEnd | 1.3.6.1.4.1.33.13.1.18.1.27 | INTEGER | read-write | Character input from the character port to move the cursor to the end of the line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR END and the value labeled 'End of Line Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorForward | 1.3.6.1.4.1.33.13.1.18.1.28 | INTEGER | read-write | Character input from the character port to move the cursor to the right. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR FORWARDS and the value labeled 'Forwards Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorInsertToggle | 1.3.6.1.4.1.33.13.1.18.1.29 | INTEGER | read-write | Character input from the character port to toggle between insert and overwrite modes. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR INSERT TOGGLE and the value labeled 'Insert Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorNextLine | 1.3.6.1.4.1.33.13.1.18.1.30 | INTEGER | read-write | Character input from the character port to recall the next, newer line in the command history. The value -1 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR NEXT LINE and the value labeled 'Next Line Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorPreviousLine | 1.3.6.1.4.1.33.13.1.18.1.31 | INTEGER | read-write | Character input from the character port to recall the previous, older line in the command history. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR PREVIOUS LINE and the value labeled 'Previous Line Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorQuotingCharacter | 1.3.6.1.4.1.33.13.1.18.1.32 | INTEGER | read-write | Character input from the character port to inhibit interpretation of the next input character. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR QUOTING CHARACTER and the value labeled 'Quoting Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicSerialPortLineEditorRedisplay | 1.3.6.1.4.1.33.13.1.18.1.33 | INTEGER | read-write | Character input from the character port to redisplay the current command line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR REDISPLAY CHARACTER and the value labeled 'Redisplay Character:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT basicConsoleLogoutDisconnect | 1.3.6.1.4.1.33.13.1.19 | INTEGER | read-write | Control for automatic session disconnection when a console port user logs out. Corresponds directly to SERVER CONSOLE LOGOUT and the presence of the label 'Console Logout' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| queue | 1.3.6.1.4.1.33.13.2 | |||
| INT queueLimit | 1.3.6.1.4.1.33.13.2.1 | INTEGER | read-write | The maximum number of entries that can be made in the Queue table. The value -1 indicates the imit is available memory. Corresponds directly to SERVER QUEUE LIMIT and the value labeled 'Queue Limit:' in the SERVER CHARACTERISTICS display. |
| GAU queueHigh | 1.3.6.1.4.1.33.13.2.2 | Gauge | read-only | The highest value of queueNumber since system initialization. Corresponds directly to the value labeled 'Queue Entries' and 'High' in the SERVER STATUS display. |
| GAU queueNumber | 1.3.6.1.4.1.33.13.2.3 | Gauge | read-only | The number of entries in the Queue table. Corresponds directly to the value labeled 'Queue Entries' and 'Cur' in the SERVER STATUS display. |
| queueTable | 1.3.6.1.4.1.33.13.2.4 | not-accessible | A list of queue entries. | |
| queueEntry | 1.3.6.1.4.1.33.13.2.4.1 | not-accessible | Parameter values for a queue entry. | |
| INT queueJob | 1.3.6.1.4.1.33.13.2.4.1.1 | INTEGER | read-only | The job number of a queued request. Corresponds directly to the value labeled 'Entry' in the QUEUE display. |
| INT queueStatus | 1.3.6.1.4.1.33.13.2.4.1.2 | INTEGER | read-write | The status of a queue entry. Set to 'invalid' to remove the entry, which corresponds directly to the REMOVE QUEUE ENTRY command. Actual removal of the entry is implementation specific. |
| STR queueSourceName | 1.3.6.1.4.1.33.13.2.4.1.3 | DisplayString | read-only | The name of the system that originated the queue entry. Corresponds directly to the value labeled 'Source Node' in the QUEUE display. |
| STR queueServiceName | 1.3.6.1.4.1.33.13.2.4.1.4 | DisplayString | read-only | The name of the service for which the originator is waiting. Corresponds directly to the value labeled 'Service' in the QUEUE display. |
| INT queueServicePortIndex | 1.3.6.1.4.1.33.13.2.4.1.5 | INTEGER | read-only | The charPortIndex of the port for which the originator is waiting, if supplied by the originator. As defined in the Character MIB [12]. Corresponds indirectly to the port number part of the value labeled 'Port Name' in the QUEUE display. |
| STR queueServicePortName | 1.3.6.1.4.1.33.13.2.4.1.6 | DisplayString | read-only | The name of the port for which the originator is waiting, if supplied by the originator. Corresponds directly to the port name part of the value labeled 'Port Name' in the SERVER QUEUE display. |
| queuePortTable | 1.3.6.1.4.1.33.13.2.5 | not-accessible | A list of queuing-related character port entries. | |
| queuePortEntry | 1.3.6.1.4.1.33.13.2.5.1 | not-accessible | Queuing parameter values for a port. | |
| INT queuePortIndex | 1.3.6.1.4.1.33.13.2.5.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Character MIB [12]. |
| INT queuePortQueuing | 1.3.6.1.4.1.33.13.2.5.1.2 | INTEGER | read-write | Control for allowing queued requests for using the port. Corresponds directly to PORT QUEUING and the presence of the label 'Queuing' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| menu | 1.3.6.1.4.1.33.13.3 | |||
| GAU menuNumber | 1.3.6.1.4.1.33.13.3.1 | Gauge | read-only | The number of entries in the Menu table. Corresponds indirectly to SERVER MENU display. |
| STR menuContinuePrompt | 1.3.6.1.4.1.33.13.3.2 | DisplayString | read-write | The text to use when prompting a menu user to press RETURN to continue. Corresponds directly to SERVER MENU CONTINUE PROMPT and the value labeled 'Menu Continue Prompt:' in the SERVER MENU display. |
| STR menuSelectionPrompt | 1.3.6.1.4.1.33.13.3.3 | DisplayString | read-write | The text to use when prompting a menu user for a menu selection. Corresponds directly to SERVER MENU PROMPT and the value labeled 'Menu Prompt:' in the SERVER MENU display. |
| menuTable | 1.3.6.1.4.1.33.13.3.4 | not-accessible | A list of menu entries. | |
| menuEntry | 1.3.6.1.4.1.33.13.3.4.1 | not-accessible | Parameter values for a menu entry. | |
| INT menuIndex | 1.3.6.1.4.1.33.13.3.4.1.1 | INTEGER | read-only | The index number of a menu entry. Corresponds directly to the numbers down the left of the SERVER MENU display. |
| INT menuStatus | 1.3.6.1.4.1.33.13.3.4.1.2 | INTEGER | read-write | The status of a the entry. Set to 'invalid' to remove the entry, which corresponds directly to the CLEAR SERVER MENU command. Actual removal of the entry is implementation specific. |
| STR menuText | 1.3.6.1.4.1.33.13.3.4.1.3 | DisplayString | read-only | The text to be displayed in the menu. Corresponds directly to the line next to the entry number in the SERVER MENU display. |
| STR menuCommand | 1.3.6.1.4.1.33.13.3.4.1.4 | DisplayString | read-only | The commands to execute when the user chooses the menu entry. Corresponds directly second line following the entry number in the SERVER MENU display. |
| menuPortTable | 1.3.6.1.4.1.33.13.3.5 | not-accessible | A list of menu-related character port entries. | |
| menuPortEntry | 1.3.6.1.4.1.33.13.3.5.1 | not-accessible | Menu parameter values for a port. | |
| INT menuPortIndex | 1.3.6.1.4.1.33.13.3.5.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Character MIB [12]. |
| INT menuPortMenuStatus | 1.3.6.1.4.1.33.13.3.5.1.2 | INTEGER | read-write | Control for menu operation on the port. Corresponds indirectly to PORT MENU and PORT PRIVILEGED MENU and the presence of the labels 'Menu' and 'Privileged Men' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| netLogin | 1.3.6.1.4.1.33.13.4 | |||
| INT netLoginNumber | 1.3.6.1.4.1.33.13.4.1 | INTEGER | read-only | The number of entries in the Network Login Server table. |
| netLoginServerTable | 1.3.6.1.4.1.33.13.4.2 | not-accessible | A list of network login server entries. | |
| netLoginServerEntry | 1.3.6.1.4.1.33.13.4.2.1 | not-accessible | Network login parameter values for a server entry. | |
| STR netLoginServerName | 1.3.6.1.4.1.33.13.4.2.1.1 | DisplayString | read-write | The name of a network login server, suitable for resolution to a network address. Corresponds directly to host portion of SERVER SCRIPT SERVER and the value labeled 'Script Host' in the SERVER PARAMETER SERVER display. |
| INT netLoginServerStatus | 1.3.6.1.4.1.33.13.4.2.1.2 | INTEGER | read-write | Status of this entry. Set to 'invalid'to remove the entry, which corresponds directly to the CLEAR SERVER SCRIPT SERVER command. Acutal removal of the entry is implementation specific. |
| STR netLoginServerPath | 1.3.6.1.4.1.33.13.4.2.1.3 | DisplayString | read-write | The full path name to the script file that is identified by the user name. Corresponds directly to path portion of SERVER SCRIPT SERVER and the value labeled 'Script Path' in the SERVER PARAMETER SERVER display. |
| netLoginPortTable | 1.3.6.1.4.1.33.13.4.3 | not-accessible | A list of network login character port entries. | |
| netLoginPortEntry | 1.3.6.1.4.1.33.13.4.3.1 | not-accessible | Network login parameter values for a port. | |
| INT netLoginPortIndex | 1.3.6.1.4.1.33.13.4.3.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Character MIB [12]. |
| INT netLoginPortScriptUse | 1.3.6.1.4.1.33.13.4.3.1.2 | INTEGER | read-write | Control for the script action taken when a user logs in on the port. Corresponds directly to PORT SCRIPT LOGIN and the value labeled 'Script Login:' in the PORT ALTERNATE CHARACTERISTICS display. |
| INT netLoginPortScriptEcho | 1.3.6.1.4.1.33.13.4.3.1.3 | INTEGER | read-write | Control for display of script operation on the port when running a script. Corresponds directly to PORT SCRIPT ECHO and the presence of the label 'Script Echo' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| ADR netLoginPortLoaderAddressType | 1.3.6.1.4.1.33.13.4.3.1.4 | AddressType | read-only | The type of network address contained in netLoginPortLoaderAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. Corresponds indirectly to the address part of the value labeled 'Script Loaded From:' in the PORT STATUS display. |
| OCT netLoginPortLoaderAddress | 1.3.6.1.4.1.33.13.4.3.1.5 | OCTET STRING | read-only | The network address of the server that provided the script for the current port login. Corresponds directly the address part of the value labeled 'Script Loaded From:' in the PORT STATUS display. |
| STR netLoginPortLoaderFile | 1.3.6.1.4.1.33.13.4.3.1.6 | DisplayString | read-only | The path and file name of the script used for the current port login. Corresponds directly the file name part of the value labeled 'Script Loaded From:' in the PORT STATUS display. |
| dial | 1.3.6.1.4.1.33.13.5 | |||
| dialPortTable | 1.3.6.1.4.1.33.13.5.1 | not-accessible | A list of dial character port entries. | |
| dialPortEntry | 1.3.6.1.4.1.33.13.5.1.1 | not-accessible | Dial parameter values for a port. | |
| INT dialPortIndex | 1.3.6.1.4.1.33.13.5.1.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Character MIB [12]. |
| INT dialPortDialback | 1.3.6.1.4.1.33.13.5.1.1.2 | INTEGER | read-write | Control for use of dialback when a user logs in on the port. Corresponds directly to PORT DIALBACK and the presence of the label 'Dialback' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| INT dialPortDialbackTimeout | 1.3.6.1.4.1.33.13.5.1.1.3 | INTEGER | read-write | The number of seconds to wait for remote modem response when dialing back. Corresponds directly to PORT DIALBACK TIMEOUT and the value labeled 'Dialback Timeout:' in the PORT ALTERNATE CHARACTERISTICS display. |
| sessionLog | 1.3.6.1.4.1.33.13.6 | |||
| INT sessionLogLimit | 1.3.6.1.4.1.33.13.6.1 | INTEGER | read-write | The maximum number of entries allowed in the Session Log table. Corresponds directly to SERVER ACCOUNTING ENTRIES and the value labeled 'Accounting Entries:' in the SERVER CHARACTERISTICS display. |
| sessionLogTable | 1.3.6.1.4.1.33.13.6.2 | not-accessible | A list of session log entries. | |
| sessionLogEntry | 1.3.6.1.4.1.33.13.6.2.1 | not-accessible | Parameter values for a session log entry. | |
| INT sessionLogIndex | 1.3.6.1.4.1.33.13.6.2.1.1 | INTEGER | read-only | The index number of a session log entry. Corresponds directly to the order of the displayed records in the SERVER ACCOUNTING display. The maximum value is sessionLogLimit. |
| INT sessionLogConnectionID | 1.3.6.1.4.1.33.13.6.2.1.2 | INTEGER | read-only | An indentifying number for records relating to the same connection, that is, the connect and disconnect records, either of which can be missing. Corresponds directly to value labeled 'Entry' the SERVER ACCOUNTING display. |
| INT sessionLogPort | 1.3.6.1.4.1.33.13.6.2.1.3 | INTEGER | read-only | An index value that uniquely identifies the port where the event took place. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Character MIB [12]. Corresponds directly to the value labeled 'Port' in the SERVER ACCOUNTING display. |
| INT sessionLogEvent | 1.3.6.1.4.1.33.13.6.2.1.4 | INTEGER | read-only | The type of event. Corresponds directly to the alphabetic part of the value labeled 'Type' in the SERVER ACCOUNTING display. |
| INT sessionLogEventDetail | 1.3.6.1.4.1.33.13.6.2.1.5 | INTEGER | read-only | The detailed reason for the event. Corresponds directly to the numeric part of the value labeled 'Type' in the SERVER ACCOUNTING display. |
| STR sessionLogUserName | 1.3.6.1.4.1.33.13.6.2.1.6 | DisplayString | read-only | The user name logged in on the port when the event occurred. Corresponds directly to the value labeled 'Username' in the SERVER ACCOUNTING display. |
| STR sessionLogRemoteName | 1.3.6.1.4.1.33.13.6.2.1.7 | DisplayString | read-only | The name of the session remote partner. Corresponds directly to the value labeled 'Destination' in the SERVER ACCOUNTING display. |
| DAT sessionLogConnectTime | 1.3.6.1.4.1.33.13.6.2.1.8 | DateTime | read-only | The date and time that session connection occurred. Corresponds directly to the value labeled 'Connect Time' in the SERVER ACCOUNTING display. |
| DAT sessionLogDisconnectTime | 1.3.6.1.4.1.33.13.6.2.1.9 | DateTime | read-only | The date and time that session disconnection occurred. Corresponds directly to the value labeled 'Disconnect Time' in the SERVER ACCOUNTING display. |
| CTR sessionLogInCharacters | 1.3.6.1.4.1.33.13.6.2.1.10 | Counter | read-only | The number of characters that came into the port for the session. Corresponds directly to the value labeled 'Bytes In' in the SERVER ACCOUNTING display. |
| CTR sessionLogOutCharacters | 1.3.6.1.4.1.33.13.6.2.1.11 | Counter | read-only | The number of characters that went out of the port for the session. Corresponds directly to the value labeled 'Bytes Out' in the SERVER ACCOUNTING display. |
| decnet | 1.3.6.1.4.1.33.14 | |||
| rcp | 1.3.6.1.4.1.33.14.1 | |||
| OCT rcpRemoteAddress | 1.3.6.1.4.1.33.14.1.1 | OCTET STRING | read-only | If a remote console session exists, the Ethernet address of the remote partner, otherwise zero length. |
RFC description
Concatenated Xyplex MIB including MIB-II, bootstrap clients/servers, character stream devices, DECnet, Ethernet interfaces, LAT, and parameter client definitions.
Start monitoring Xyplex (MRV Communications) terminal server / network access device (bundled system/interface/config status, umbrella module) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.