Wellfleet-ATM-LE-MIB

All MIBs › Wellfleet-ATM-LE-MIB

Category: Wellfleet BayNetworks ATM

Description: Manages Wellfleet ATM LAN Emulation service parameters, ELAN memberships, and LE client status.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Wellfleet-ATM-LE-MIB?

Wellfleet-ATM-LE-MIB is a proprietary MIB from Wellfleet Communications/Bay Networks covering ATM LAN Emulation (LANE) service on its routers, a technology that allows legacy Ethernet/Token Ring LAN traffic to run over an ATM backbone. It exposes configuration and status objects for emulated LAN (ELAN) memberships and the state of LAN Emulation Clients (LECs) connecting to those ELANs. It is used to monitor the software/service status of the LANE subsystem -- for instance whether a LEC has successfully joined its ELAN and is operational -- which is important because a failed LEC join effectively takes a bridged LAN segment offline even though the underlying ATM hardware may be healthy. It depends conceptually on the standard ATM Forum LANE specification and on Wellfleet's underlying ATM interface MIBs for physical-layer status. It was typically deployed in enterprise or carrier networks of the 1990s where ATM backbones carried emulated legacy LAN traffic between sites. Engineers can download the Wellfleet-ATM-LE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-ATM-LE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Wellfleet/Bay Networks router with ATM interfaces (legacy)

Monitoring Examples

No sample objects were provided, so this is inferred: an administrator would poll the ELAN membership and LEC status objects to confirm each LAN Emulation Client shows as successfully joined to its target ELAN. A LEC stuck in an initializing or failed-join state would explain why devices on that emulated LAN segment cannot reach each other, even if the ATM physical interface itself reports as up.

What Can Be Monitored

ELAN membership status
LAN Emulation Client (LEC) join/operational state
ATM LANE service status

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter

From RFC1213-MIB

DisplayString

From Wellfleet-COMMON-MIB

wfAtmLeGroup

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wfAtmLecConfigTable	1.3.6.1.4.1.18.3.5.9.5.20.1		not-accessible	ATM LEC Interface table - One per LEC Client This table deals with configuration and operational status
wfAtmLecConfigEntry	1.3.6.1.4.1.18.3.5.9.5.20.1.1		not-accessible	per LEC Client objects - wfAtmLecCct corresponds to Wellfleet circuit number
INT wflecConfDelete	1.3.6.1.4.1.18.3.5.9.5.20.1.1.1	INTEGER	read-write	Indication to create or delete an ATM LE Client Config Entry from the MIB
INT wflecRowStatus	1.3.6.1.4.1.18.3.5.9.5.20.1.1.2	INTEGER	read-write	Indication to create or delete an ATM LE Client. This will remove the LEC from the Emulated LAN. However, the instance is not removed from the MIB
INT wflecConfigCct	1.3.6.1.4.1.18.3.5.9.5.20.1.1.3	INTEGER	read-only	This corresponds to the Wellfleet circuit number
STR wflecOwner	1.3.6.1.4.1.18.3.5.9.5.20.1.1.4	DisplayString	read-write	The entity that configured this entry and is therefore using the resources assigned to it.
INT wflecConfigMode	1.3.6.1.4.1.18.3.5.9.5.20.1.1.5	INTEGER	read-write	Indicates whether this LAN Emulation Client should auto-configure the next time it is (re)started.
INT wflecConfigLanType	1.3.6.1.4.1.18.3.5.9.5.20.1.1.6	INTEGER	read-write	C2 - LEC LAN Type The data frame format which this client will use the next time it returns to the Initial State. Auto-configuring clients use this parameter in their Configure requests. Manually-configured clients use it in their Join requests.
INT wflecConfigMaxDataFrameSize	1.3.6.1.4.1.18.3.5.9.5.20.1.1.7	INTEGER	read-write	C3 Maximum Data Frame Size. The maximum data frame size which this client will use the next time it returns to the Initial State. Auto-configuring clients use this parameter in their Configure requests. Manually-configured clients use it in their Join requests. This MIB object will not be overwritten with the new value from a LE_{JOIN,CONFIGURE}_RESPONSE. Instead, lecActualMaxDataFrameSize will be.'
STR wflecConfigLanName	1.3.6.1.4.1.18.3.5.9.5.20.1.1.8	DisplayString	read-write	C5 ELAN Name. The ELAN Name this client will use the next time it returns to the Initial State. Auto-configuring clients use this parameter in their Configure requests. Manually-configured clients use it in their Join requests. This MIB object will not be overwritten with the new value from a LE_{JOIN,CONFIGURE}_RESPONSE. Instead, lecActualMaxDataFrameSize will be.'
OCT wflecConfigLesAtmAddress	1.3.6.1.4.1.18.3.5.9.5.20.1.1.9	OCTET STRING	read-write	C9 LE Server ATM Address. The LAN Emulation Server which this client will use the next time it is started in manual configuration mode. When lecConfigMode is 'automatic', there is no need to set this address, and no advantage to doing so. The client will use the LECS to find a LES, putting the auto-configured address in lecActualLesAtmAddress while leaving lecConfigLesAtmAddress alone.
INT wflecControlTimeout	1.3.6.1.4.1.18.3.5.9.5.20.1.1.10	INTEGER	read-write	C7 Control Time-out. Time out period used for timing out most request/response control frame most request/response control frame interactions.
INT wflecMaxUnknownFrameCount	1.3.6.1.4.1.18.3.5.9.5.20.1.1.11	INTEGER	read-write	C10 Maximum Unknown Frame Count. This parameter MUST be less than or equal to 10. (See parameter C11)
INT wflecMaxUnknownFrameTime	1.3.6.1.4.1.18.3.5.9.5.20.1.1.12	INTEGER	read-write	C11 Maximum Unknown Frame Time. This parameter MUST be greater than or equal to 1.0 seconds. Within the period of time defined by the Maximum Unknown Frame Time, a LE Client will send no more than Maximum Unknown Frame Count frames to a given MAC address or Route Designator without also initiating the address resolution protocol to resolve that MAC address or Route Designator. This time value is expressed in seconds.
INT wflecVccTimeoutPeriod	1.3.6.1.4.1.18.3.5.9.5.20.1.1.13	INTEGER	read-write	C12 VCC Timeout Period. A LE Client may release any Data Direct or Multicast Send VCC that it has not used to transmit or receive any data frames for the length of the VCC Timeout Period. This time value is expressed in seconds.
INT wflecMaxRetryCount	1.3.6.1.4.1.18.3.5.9.5.20.1.1.14	INTEGER	read-write	C13 Maximum Retry Count. A LE CLient MUST not retry a LE-ARP for a given frame's LAN destination more than Maximum Retry Count times, after which it must discard the frame.
INT wflecAgingTime	1.3.6.1.4.1.18.3.5.9.5.20.1.1.15	INTEGER	read-write	C17 Aging Time. The maximum time that a LE Client will maintain an entry in its LE-ARP cache in the absence of a verification of that relationship.
INT wflecForwardDelayTime	1.3.6.1.4.1.18.3.5.9.5.20.1.1.16	INTEGER	read-write	C18 Forward Delay Time. The maximum time that a LE Client will maintain an entry in its LE-ARP cache in the absence of a verification of that relationship, so long as the Topology Change flag C19 is true.
INT wflecExpectedArpResponseTime	1.3.6.1.4.1.18.3.5.9.5.20.1.1.17	INTEGER	read-write	C20 Expected LE_ARP Reponse Time. The maximum time (seconds) that the LEC expects an LE_ARP_REQUEST/ LE_ARP_RESPONSE cycle to take. Used for retries and verifies.
INT wflecFlushTimeOut	1.3.6.1.4.1.18.3.5.9.5.20.1.1.18	INTEGER	read-write	C21 Flush Time-out. Time limit (seconds) to wait to receive a LE_FLUSH_RESPONSE after the LE_FLUSH_REQUEST has been sent before taking recovery action.
INT wflecPathSwitchingDelay	1.3.6.1.4.1.18.3.5.9.5.20.1.1.19	INTEGER	read-write	C22 Path Switching Delay. The time (seconds) since sending a frame to the BUS after which the LE Client may assume that the frame has been either discarded or delivered to the recipient. May be used to bypass the Flush protocol.
INT wflecLocalSegmentID	1.3.6.1.4.1.18.3.5.9.5.20.1.1.20	INTEGER	read-write	C23 Local Segment ID. The segment ID of the emulated LAN. This is only required for IEEE 802.5 clients that are Source Routing bridges.'
INT wflecMulticastSendType	1.3.6.1.4.1.18.3.5.9.5.20.1.1.21	INTEGER	read-write	C24 Multicast Send VCC Type. Signalling parameter that SHOULD be used by the LE Client when establishing the Multicast Send VCC. This is the method to be used by the LE Client when specifying traffic parameters when it sets up the Multicast Send VCC for this emulated LAN.
INT wflecMulticastSendAvgRate	1.3.6.1.4.1.18.3.5.9.5.20.1.1.22	INTEGER	read-write	C25 Multicast Send VCC AvgRate. Signalling parameter that SHOULD be used by the LE Client when establishing the Multicast Send VCC. Forward and Backward Sustained Cell Rate to be requested by LE Client when setting up Multicast Send VCC, if using Variable bit rate codings.
INT wflecMulticastSendPeakRate	1.3.6.1.4.1.18.3.5.9.5.20.1.1.23	INTEGER	read-write	C26 Multicast Send VCC PeakRate. Signalling parameter that SHOULD be used by the LE Client when establishing the Multicast Send VCC. Forward and Backward Peak Cell Rate to be requested by LE Client when setting up Multicast Send VCC, if using Variable bit rate codings.
INT wflecConnectionCompleteTimer	1.3.6.1.4.1.18.3.5.9.5.20.1.1.24	INTEGER	read-write	C28 Connection Complete Timer. Optional. In Connection Establishment this is the time period in which data or a READY_IND message is expected from a Calling Party.
INT wflecFlushEnable	1.3.6.1.4.1.18.3.5.9.5.20.1.1.25	INTEGER	read-write	Flush Protocol enable/disable - ATM_LEC_FLUSH_ENABLED - ATM LE flush protocol is used when switching VCs. If the Flush timeout (wflecFlushTimeOut) expires data for that MAC address will start flowing over the old VC again. ATM_LEC_FLUSH_DISABLED - ATM LE flush protocol is not used. Instead data for that MAC address will automatically start flowing over the new VC once the Path Switching delay timeout (wflecPathSwitchingDelay) has expired.
INT wflecConfigRetry	1.3.6.1.4.1.18.3.5.9.5.20.1.1.26	INTEGER	read-write	This attribute specifies how many retries should be attempted if any part of the config phase fails. The config phase starts with setting up the config direct VC and ends when a JOIN response is received. The default is 0 which means retry forever with a maximum timeout of 30 seconds between each retry. The time between each retry will start at 2 seconds and double from that point (never exceeding 30 seconds).
INT wflecMulticastFwdTimeout	1.3.6.1.4.1.18.3.5.9.5.20.1.1.27	INTEGER	read-write	The attribute specifies how many seconds to wait for the Multicast Forward VC to be set up before retrying. The retry will include closing the Multicast Send VC (if it has been opened) and reARPing for the BUS. A successful ARP response will result in the setup of the Multicast Send which in turn should result in the BUS setting up the Multicast Forward VC.
INT wflecMulticastFwdRetry	1.3.6.1.4.1.18.3.5.9.5.20.1.1.28	INTEGER	read-write	The attribute specifies how many retries should be made to get the Multicast Forward VC setup. The LEC will retry after wflecMulticastFwdTimeout seconds and will double this timeout for each each retry which follows. The timeout will not exeed 30 seconds however. After wflecMulticastFwdRetry retries, the LEC will restart itself. If wflecMulticastFwdRetry is set to 0 it will retry the BUS phase forever and will never restart itself.
INT wflecDebugLevel	1.3.6.1.4.1.18.3.5.9.5.20.1.1.29	INTEGER	read-write	Debug Levels - The level of debug desired from the Portable LEC code LEC_DBG_OFF - 0 LEC_DBG_WARN - 1 LEC_DBG_ERR - 2 LEC_DBG_MSG - 4 LEC_DBG_DBG - 8 LEC_DBG_VERBOSE - 16 This values above can be used separately, or OR'd together for a combination of debug levels. For example, to see both WARN and ERR messages, LEC_DBG_WARN OR LEC_DBG_ERR = 3, so set this object to 3.
OCT wflecConfigLECSAtmAddress	1.3.6.1.4.1.18.3.5.9.5.20.1.1.30	OCTET STRING	read-write	The LE Config Server Address to be used. If left (or set) to NULL_VAL the well-known LECS ATM address will be used.
INT wflecConfigV2Capable	1.3.6.1.4.1.18.3.5.9.5.20.1.1.31	INTEGER	read-write	Indication to enable or disable LANE V2 support for this ATM LE Client.
wfAtmLecStatusTable	1.3.6.1.4.1.18.3.5.9.5.20.2		not-accessible	Lan Emulation Status Group Read-only table containing identification, status, and operational information about the LAN Emulation Clients this agent manages
wfAtmLecStatusEntry	1.3.6.1.4.1.18.3.5.9.5.20.2.1		not-accessible	per LEC Client objects - wfAtmLecCct corresponds to Wellfleet circuit number
INT wflecStatusCct	1.3.6.1.4.1.18.3.5.9.5.20.2.1.1	INTEGER	read-only	This corresponds to the Wellfleet circuit number
OCT wflecPrimaryAtmAddress	1.3.6.1.4.1.18.3.5.9.5.20.2.1.2	OCTET STRING	read-only	C1 - LE Client's ATM Address.
INT wflecID	1.3.6.1.4.1.18.3.5.9.5.20.2.1.3	INTEGER	read-only	C14 LE Client Identifier. Each LE Client requires a LE Client Identifier (LECID) assigned by the LE Server during the Join phase. The LECID is placed in control requests by the LE Client and MAY be used for echo suppression on multicast data frames sent by that LE Client. This value MUST NOT change without terminating the LE Client and returning to the Initial state. A valid LECID MUST be in the range X'0001' through X'FEFF'. The value of this object is only meaningful for a LEC that is connected to a LES. For a LEC which does not belong to an emulated LAN, the value of this object is defined to be 0.'
INT wflecInterfaceState	1.3.6.1.4.1.18.3.5.9.5.20.2.1.4	INTEGER	read-only	Indicates the state for the LE Client
INT wflecLastFailureRespCode	1.3.6.1.4.1.18.3.5.9.5.20.2.1.5	INTEGER	read-only	Failure response code. Status code from the last failed Configure response or Join response. Failed responses are those for which the LE_CONFIGURE_RESPONSE / LE_JOIN_RESPONSE frame contains a non-zero code, or fails to arrive within a timeout period. If none of this client's requests have failed, this object has the value 'none'. If the failed response contained a STATUS code that is not defined in the LAN Emulation specification, this object has the value 'undefinedError'. The value 'timeout' is self-explanatory. Other failure codes correspond to those defined in the specification, although they may have different numeric values.
INT wflecLastFailureState	1.3.6.1.4.1.18.3.5.9.5.20.2.1.6	INTEGER	read-only	Last failure state The state this client was in when it updated the 'lecLastFailureRespCode'. If 'lecLastFailureRespCode' is 'none', this object has the value initialState(1).
INT wflecProtocol	1.3.6.1.4.1.18.3.5.9.5.20.2.1.7	INTEGER	read-only	The LAN Emulation protocol which this client supports, and specifies in its LE_JOIN_REQUESTs.
INT wflecVersion	1.3.6.1.4.1.18.3.5.9.5.20.2.1.8	INTEGER	read-only	The LAN Emulation protocol version which this client supports, and specifies in its LE_JOIN_REQUESTs.
INT wflecTopologyChange	1.3.6.1.4.1.18.3.5.9.5.20.2.1.9	INTEGER	read-only	C19 Topology Change. Boolean indication that the LE Client is using the Forward Delay Time C18, instead of the Ageing Time C17, to age entries in its LE-ARP cache.
OCT wflecConfigServerAtmAddress	1.3.6.1.4.1.18.3.5.9.5.20.2.1.10	OCTET STRING	read-only	The ATM address of the LECS for this Client
INT wflecConfigSource	1.3.6.1.4.1.18.3.5.9.5.20.2.1.11	INTEGER	read-only	Indicates whether this LAN Emulation Client used the LAN Emulation Configuration Server, and, if so, what method it used to establish the Configuration Direct VCC.
INT wflecActualLanType	1.3.6.1.4.1.18.3.5.9.5.20.2.1.12	INTEGER	read-only	C2 - LEC LAN Type The data frame format that this LAN Emulation Client is using right now. This may come from lecConfigLanType, the LAN Emulation Configuration Server, or the LAN Emulation Server
INT wflecActualMaxDataFrameSize	1.3.6.1.4.1.18.3.5.9.5.20.2.1.13	INTEGER	read-only	C3 Maximum Data Frame Size. The maximum data frame size that this LAN Emulation client is using right now. This may come from lecConfigLanType, the LAN Emulation Configuration Server, or the LAN Emulation Server
STR wflecActualLanName	1.3.6.1.4.1.18.3.5.9.5.20.2.1.14	DisplayString	read-only	C5 ELAN Name. The identity of the emulated LAN which this client last joined, or wishes to join. This may come from lecConfigLanType, the LAN Emulation Configuration Server, or the LAN Emulation Server
OCT wflecActualLesAtmAddress	1.3.6.1.4.1.18.3.5.9.5.20.2.1.15	OCTET STRING	read-only	C9 LE Server ATM Address. The LAN Emulation Server address currently in use or most recently attempted. If no LAN Emulation Server attachment has been tried, this object's value is the zero-length string.'
INT wflecProxyClient	1.3.6.1.4.1.18.3.5.9.5.20.2.1.16	INTEGER	read-only	C4 Proxy When a client joins an ATM emulated LAN, it indicates whether it wants to act as a proxy. Proxy clients are allowed to represent unregistered MAC addresses, and receive copies of LE_ARP_REQUEST frames for such addresses.'
wfAtmLecOperConfigTable	1.3.6.1.4.1.18.3.5.9.5.20.3		not-accessible	ATM LEC Interface table - One per LEC Client This table deals with configuration and operational status
wfAtmLecOperConfigEntry	1.3.6.1.4.1.18.3.5.9.5.20.3.1		not-accessible	per LEC Operation Config objects - wfAtmLecOperConfigCct corresponds to Wellfleet circuit number
INT wflecOperConfigCct	1.3.6.1.4.1.18.3.5.9.5.20.3.1.1	INTEGER	read-only	This corresponds to the Wellfleet circuit number
INT wflecOperConfigControlTimeout	1.3.6.1.4.1.18.3.5.9.5.20.3.1.2	INTEGER	read-only	C7 Control Time-out. Time out period used for timing out most request/response control frame most request/response control frame interactions.
INT wflecOperConfigMaxUnknownFrameCount	1.3.6.1.4.1.18.3.5.9.5.20.3.1.3	INTEGER	read-only	C10 Maximum Unknown Frame Count. This parameter MUST be less than or equal to 10. (See parameter C11)
INT wflecOperConfigMaxUnknownFrameTime	1.3.6.1.4.1.18.3.5.9.5.20.3.1.4	INTEGER	read-only	C11 Maximum Unknown Frame Time. This parameter MUST be greater than or equal to 1.0 seconds. Within the period of time defined by the Maximum Unknown Frame Time, a LE Client will send no more than Maximum Unknown Frame Count frames to a given MAC address or Route Designator without also initiating the address resolution protocol to resolve that MAC address or Route Designator. This time value is expressed in seconds.
INT wflecOperConfigVccTimeoutPeriod	1.3.6.1.4.1.18.3.5.9.5.20.3.1.5	INTEGER	read-only	C12 VCC Timeout Period. A LE Client may release any Data Direct or Multicast Send VCC that it has not used to transmit or receive any data frames for the length of the VCC Timeout Period. This time value is expressed in seconds.
INT wflecOperConfigMaxRetryCount	1.3.6.1.4.1.18.3.5.9.5.20.3.1.6	INTEGER	read-only	C13 Maximum Retry Count. A LE CLient MUST not retry a LE-ARP for a given frame's LAN destination more than Maximum Retry Count times, after which it must discard the frame.
INT wflecOperConfigAgingTime	1.3.6.1.4.1.18.3.5.9.5.20.3.1.7	INTEGER	read-only	C17 Aging Time. The maximum time that a LE Client will maintain an entry in its LE-ARP cache in the absence of a verification of that relationship.
INT wflecOperConfigForwardDelayTime	1.3.6.1.4.1.18.3.5.9.5.20.3.1.8	INTEGER	read-only	C18 Forward Delay Time. The maximum time that a LE Client will maintain an entry in its LE-ARP cache in the absence of a verification of that relationship, so long as the Topology Change flag C19 is true.
INT wflecOperConfigTopologyChange	1.3.6.1.4.1.18.3.5.9.5.20.3.1.9	INTEGER	read-only	C19 Topology Change. Boolean indication that the LE Client is using the Forward Delay Time C18, instead of the Ageing Time C17, to age entries in its LE-ARP cache.
INT wflecOperConfigExpectedArpResponseTime	1.3.6.1.4.1.18.3.5.9.5.20.3.1.10	INTEGER	read-only	C20 Expected LE_ARP Reponse Time. The maximum time (seconds) that the LEC expects an LE_ARP_REQUEST/ LE_ARP_RESPONSE cycle to take. Used for retries and verifies.
INT wflecOperConfigFlushTimeOut	1.3.6.1.4.1.18.3.5.9.5.20.3.1.11	INTEGER	read-only	C21 Flush Time-out. Time limit (seconds) to wait to receive a LE_FLUSH_RESPONSE after the LE_FLUSH_REQUEST has been sent before taking recovery action.
INT wflecOperConfigPathSwitchingDelay	1.3.6.1.4.1.18.3.5.9.5.20.3.1.12	INTEGER	read-only	C22 Path Switching Delay. The time (seconds) since sending a frame to the BUS after which the LE Client may assume that the frame has been either discarded or delivered to the recipient. May be used to bypass the Flush protocol.
INT wflecOperConfigLocalSegmentID	1.3.6.1.4.1.18.3.5.9.5.20.3.1.13	INTEGER	read-only	C23 Local Segment ID. The segment ID of the emulated LAN. This is only required for IEEE 802.5 clients that are Source Routing bridges.'
INT wflecOperConfigMulticastSendType	1.3.6.1.4.1.18.3.5.9.5.20.3.1.14	INTEGER	read-only	C24 Multicast Send VCC Type. Signalling parameter that SHOULD be used by the LE Client when establishing the Multicast Send VCC. This is the method to be used by the LE Client when specifying traffic parameters when it sets up the Multicast Send VCC for this emulated LAN.
INT wflecOperConfigMulticastSendAvgRate	1.3.6.1.4.1.18.3.5.9.5.20.3.1.15	INTEGER	read-only	C25 Multicast Send VCC AvgRate. Signalling parameter that SHOULD be used by the LE Client when establishing the Multicast Send VCC. Forward and Backward Sustained Cell Rate to be requested by LE Client when setting up Multicast Send VCC, if using Variable bit rate codings.
INT wflecOperConfigMulticastSendPeakRate	1.3.6.1.4.1.18.3.5.9.5.20.3.1.16	INTEGER	read-only	C26 Multicast Send VCC PeakRate. Signalling parameter that SHOULD be used by the LE Client when establishing the Multicast Send VCC. Forward and Backward Peak Cell Rate to be requested by LE Client when setting up Multicast Send VCC, if using Variable bit rate codings.
INT wflecOperConfigConnectionCompleteTimer	1.3.6.1.4.1.18.3.5.9.5.20.3.1.17	INTEGER	read-only	C28 Connection Complete Timer. Optional. In Connection Establishment this is the time period in which data or a READY_IND message is expected from a Calling Party.
wfAtmLecStatisticsTable	1.3.6.1.4.1.18.3.5.9.5.20.4		not-accessible	Table of statistics
wfAtmLecStatisticsEntry	1.3.6.1.4.1.18.3.5.9.5.20.4.1		not-accessible	Entry contains statistics for each LEC
CTR wflecArpRequestsOut	1.3.6.1.4.1.18.3.5.9.5.20.4.1.1	Counter	read-only	The number of MAC-to-ATM ARP requests made by this LAN Emulation client over the LUNI associated with this emulated packet interface.
CTR wflecArpRequestsIn	1.3.6.1.4.1.18.3.5.9.5.20.4.1.2	Counter	read-only	The number of MAC-to-ATM ARP requests received by this LAN Emulation client over the LUNI associated with this emulated packet interface. Requests may arrive on the Control Direct VCC or on the Control Distribute VCC, depending upon how the LES is implemented and the chances it has had for learning. This counter covers both VCCs.
CTR wflecArpRepliesOut	1.3.6.1.4.1.18.3.5.9.5.20.4.1.3	Counter	read-only	The number of MAC-to-ATM ARP replies sent by this LAN Emulation client over the LUNI associated with this emulated packet interface.
CTR wflecArpRepliesIn	1.3.6.1.4.1.18.3.5.9.5.20.4.1.4	Counter	read-only	The number of MAC-to-ATM ARP replies received by this LAN Emulation client over the LUNI associated with this emulated packet interface. This count includes all such replies, whether solicited or not. Replies may arrive on the Control Direct VCC or on the Control Distribute VCC, depending upon how the LES is implemented. This counter covers both VCCs.
CTR wflecControlFramesOut	1.3.6.1.4.1.18.3.5.9.5.20.4.1.5	Counter	read-only	The total number of control packets sent by this LAN Emulation client over the LUNI associated with this emulated packet interface.
CTR wflecControlFramesIn	1.3.6.1.4.1.18.3.5.9.5.20.4.1.6	Counter	read-only	The total number of control packets received by this LAN Emulation client over the LUNI associated with this emulated packet interface
CTR wflecSvcFailures	1.3.6.1.4.1.18.3.5.9.5.20.4.1.7	Counter	read-only	The number of SVCs which this client tried to, but failed to, open.
INT wflecStatisticsCct	1.3.6.1.4.1.18.3.5.9.5.20.4.1.8	INTEGER	read-only	This corresponds to the Wellfleet circuit number
CTR wflecUnknownFramesDropped	1.3.6.1.4.1.18.3.5.9.5.20.4.1.9	Counter	read-only	The number of frames that have been dropped due to unknown frame pacing.
CTR wflecInDataFrames	1.3.6.1.4.1.18.3.5.9.5.20.4.1.10	Counter	read-only
CTR wflecInUnicastFrames	1.3.6.1.4.1.18.3.5.9.5.20.4.1.11	Counter	read-only
CTR wflecInUnicastOctets	1.3.6.1.4.1.18.3.5.9.5.20.4.1.12	Counter	read-only
CTR wflecInMulticastFrames	1.3.6.1.4.1.18.3.5.9.5.20.4.1.13	Counter	read-only
CTR wflecInMulticastOctets	1.3.6.1.4.1.18.3.5.9.5.20.4.1.14	Counter	read-only
CTR wflecInBroadcastFrames	1.3.6.1.4.1.18.3.5.9.5.20.4.1.15	Counter	read-only
CTR wflecInBroadcastOctets	1.3.6.1.4.1.18.3.5.9.5.20.4.1.16	Counter	read-only
CTR wflecOutDataFrames	1.3.6.1.4.1.18.3.5.9.5.20.4.1.17	Counter	read-only
CTR wflecOutUnknownFrames	1.3.6.1.4.1.18.3.5.9.5.20.4.1.18	Counter	read-only
CTR wflecOutUnknownOctets	1.3.6.1.4.1.18.3.5.9.5.20.4.1.19	Counter	read-only
CTR wflecOutMulticastFrames	1.3.6.1.4.1.18.3.5.9.5.20.4.1.20	Counter	read-only
CTR wflecOutMulticastOctets	1.3.6.1.4.1.18.3.5.9.5.20.4.1.21	Counter	read-only
CTR wflecOutBroadcastFrames	1.3.6.1.4.1.18.3.5.9.5.20.4.1.22	Counter	read-only
CTR wflecOutBroadcastOctets	1.3.6.1.4.1.18.3.5.9.5.20.4.1.23	Counter	read-only
CTR wflecOutUnicastFrames	1.3.6.1.4.1.18.3.5.9.5.20.4.1.24	Counter	read-only
CTR wflecOutUnicastOctets	1.3.6.1.4.1.18.3.5.9.5.20.4.1.25	Counter	read-only
wfAtmLecServerVccTable	1.3.6.1.4.1.18.3.5.9.5.20.5		not-accessible	Lan Emulation Client - Server VCC Table
wfAtmLecServerVccEntry	1.3.6.1.4.1.18.3.5.9.5.20.5.1		not-accessible	Entry contains statistics for each LEC
INT wflecConfigDirectInterface	1.3.6.1.4.1.18.3.5.9.5.20.5.1.1	INTEGER	read-only	The interface associated with the Configuration Direct VCC. If no Configuration Direct VCC exists, this object has the value 0. Otherwise, the objects ( wflecConfigDirectInterface, wflecConfigDirectVPI, wflecConfigDirectVCI ) identify the circuit
INT wflecConfigDirectVpi	1.3.6.1.4.1.18.3.5.9.5.20.5.1.2	INTEGER	read-only	If the Configuration Direct VCC exists, this object contains the VPI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0.
INT wflecConfigDirectVci	1.3.6.1.4.1.18.3.5.9.5.20.5.1.3	INTEGER	read-only	If the Configuration Direct VCC exists, this object contains the VCI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0.
INT wflecControlDirectInterface	1.3.6.1.4.1.18.3.5.9.5.20.5.1.4	INTEGER	read-only	The interface associated with the Control Direct VCC. If no Control Direct VCC exists, this object has the value 0. Otherwise, the objects ( wflecControlDirectInterface, wflecControlDirectVPI, wflecControlDirectVCI ) identify the circuit
INT wflecControlDirectVpi	1.3.6.1.4.1.18.3.5.9.5.20.5.1.5	INTEGER	read-only	If the Control Direct VCC exists, this object contains the VPI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0.
INT wflecControlDirectVci	1.3.6.1.4.1.18.3.5.9.5.20.5.1.6	INTEGER	read-only	If the Control Direct VCC exists, this object contains the VCI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0.
INT wflecControlDistributeInterface	1.3.6.1.4.1.18.3.5.9.5.20.5.1.7	INTEGER	read-only	The interface associated with the Control Distribute VCC. If no Control Distribute VCC exists, this object has the value 0. Otherwise, the objects ( wflecControlDistributeInterface, wflecControlDistributeVPI, wflecControlDistributeVCI ) identify the circuit
INT wflecControlDistributeVpi	1.3.6.1.4.1.18.3.5.9.5.20.5.1.8	INTEGER	read-only	If the Control Distribute VCC exists, this object contains the VPI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0.
INT wflecControlDistributeVci	1.3.6.1.4.1.18.3.5.9.5.20.5.1.9	INTEGER	read-only	If the Control Distribute VCC exists, this object contains the VCI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0.
INT wflecMulticastSendInterface	1.3.6.1.4.1.18.3.5.9.5.20.5.1.10	INTEGER	read-only	The interface associated with the Multicast Send VCC. If no Multicast Send VCC exists, this object has the value 0. Otherwise, the objects ( wflecMulticastSendInterface, wflecMulticastSendVPI, wflecMulticastSendVCI ) identify the circuit
INT wflecMulticastSendVpi	1.3.6.1.4.1.18.3.5.9.5.20.5.1.11	INTEGER	read-only	If the Multicast Send VCC exists, this object contains the VPI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0.
INT wflecMulticastSendVci	1.3.6.1.4.1.18.3.5.9.5.20.5.1.12	INTEGER	read-only	If the Multicast Send VCC exists, this object contains the VCI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0.
INT wflecMulticastForwardInterface	1.3.6.1.4.1.18.3.5.9.5.20.5.1.13	INTEGER	read-only	The interface associated with the Multicast Forward VCC. If no Multicast Forward VCC exists, this object has the value 0. Otherwise, the objects ( wflecMulticastForwardInterface, wflecMulticastForwardVPI, wflecMulticastForwardVCI ) identify the circuit
INT wflecMulticastForwardVpi	1.3.6.1.4.1.18.3.5.9.5.20.5.1.14	INTEGER	read-only	If the Multicast Forward VCC exists, this object contains the VPI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0.
INT wflecMulticastForwardVci	1.3.6.1.4.1.18.3.5.9.5.20.5.1.15	INTEGER	read-only	If the Multicast Forward VCC exists, this object contains the VCI which identifies that VCC at the point where it connects to this LE client. Otherwise, this object has the value 0.
INT wflecServerVccCct	1.3.6.1.4.1.18.3.5.9.5.20.5.1.16	INTEGER	read-only	This corresponds to the Wellfleet circuit number
wfAtmLecAtmAddressTable	1.3.6.1.4.1.18.3.5.9.5.20.6		not-accessible	LAN Emulation Client - ATM Addresses table
wfAtmLecAtmAddressEntry	1.3.6.1.4.1.18.3.5.9.5.20.6.1		not-accessible	Entry contains ATM address for a LE CLient
OCT wflecAtmAddress	1.3.6.1.4.1.18.3.5.9.5.20.6.1.1	OCTET STRING	read-only	The ATM address this row describes. This could be either a primary address or a secondary address.
INT wflecAtmAddressStatus	1.3.6.1.4.1.18.3.5.9.5.20.6.1.2	INTEGER	read-write	Used to create and delete rows in this table. A management station cannot disable an ATM address while the client is up
INT wflecAtmAddressCct	1.3.6.1.4.1.18.3.5.9.5.20.6.1.3	INTEGER	read-only	This corresponds to the Wellfleet circuit number
wfAtmLecMacAddressTable	1.3.6.1.4.1.18.3.5.9.5.20.7		not-accessible	LAN Emulation Client - MAC Addresses table
wfAtmLecMacAddressEntry	1.3.6.1.4.1.18.3.5.9.5.20.7.1		not-accessible	Entry contains MAC address for a LE CLient
OCT wflecMacAddress	1.3.6.1.4.1.18.3.5.9.5.20.7.1.1	OCTET STRING	read-only	The MAC address this row describes. This could be either a primary address or a secondary address.
OCT wflecMacAddressAtmBinding	1.3.6.1.4.1.18.3.5.9.5.20.7.1.2	OCTET STRING	read-only	The ATM Address registered for wflecMacAddress
INT wflecMacAddressCct	1.3.6.1.4.1.18.3.5.9.5.20.7.1.3	INTEGER	read-only	This corresponds to the Wellfleet circuit number
wfAtmLeArpTable	1.3.6.1.4.1.18.3.5.9.5.20.8		not-accessible	Lan Emulation Client ARP Cache Group This table provides access to an ATM LAN Emulation Client's MAC-to-ATM ARP cache. It contains entries for unicast addresses and for the broadcast address, but not for multicast MAC addresses.
wfAtmLeArpEntry	1.3.6.1.4.1.18.3.5.9.5.20.8.1		not-accessible	entry of MAC address to ATM address
OCT wfleArpMacAddress	1.3.6.1.4.1.18.3.5.9.5.20.8.1.1	OCTET STRING	read-only	The MAC address for which this cache entry provides a translation. Since ATM LAN Emulation uses an ARP protocol to locate broadcast and multicast servers, the value of this object could be the broadcast MAC address
OCT wfleArpAtmAddress	1.3.6.1.4.1.18.3.5.9.5.20.8.1.2	OCTET STRING	read-only	The ATM address of the Broadcast & Unknown Server or LAN Emulation Client whose MAC address is stored in 'leArpMacAddress'.
INT wfleArpIsRemoteAddress	1.3.6.1.4.1.18.3.5.9.5.20.8.1.3	INTEGER	read-only	Indicates whether the 'leArpMACaddress' belongs to a remote client. true(1) The address is believed to be remote - or its local/remote status is unknown. For an entry created via the LE_ARP mechanism, this corresponds to the 'Remote address' flag being set in the LE_ARP_RESPONSE. false(2) The address is believed to be local - that is to say, registered with the LES by the client whose ATM address is leArpAtmAddress.
INT wfleArpEntryType	1.3.6.1.4.1.18.3.5.9.5.20.8.1.4	INTEGER	read-only	Indicates how this LE_ARP table entry was created and whether it is aged.
INT wfleArpRowStatus	1.3.6.1.4.1.18.3.5.9.5.20.8.1.5	INTEGER	read-write	Row status of enable or disable
INT wfleArpCct	1.3.6.1.4.1.18.3.5.9.5.20.8.1.6	INTEGER	read-only	This corresponds to the Wellfleet circuit number
INT wfleArpVpi	1.3.6.1.4.1.18.3.5.9.5.20.8.1.7	INTEGER	read-only	This is the Vpi will be used for this MAC address
INT wfleArpVci	1.3.6.1.4.1.18.3.5.9.5.20.8.1.8	INTEGER	read-only	This is the Vci will be used for this MAC address
wfAtmLeRDArpTable	1.3.6.1.4.1.18.3.5.9.5.20.9		not-accessible	Lan Emulation Client RDArp Cache Group This table provides access to an ATM LAN Emulation Client's Route Descriptor-to-ATM ARP cache.
wfAtmLeRDArpEntry	1.3.6.1.4.1.18.3.5.9.5.20.9.1		not-accessible	entry of Route Descriptor to ATM address
INT wfleRDArpSegmentID	1.3.6.1.4.1.18.3.5.9.5.20.9.1.1	INTEGER	read-only	The LAN ID portion of the Route Descriptor associated with this ARP cache entry.
INT wfleRDArpBridgeNumber	1.3.6.1.4.1.18.3.5.9.5.20.9.1.2	INTEGER	read-only	The Bridge Number portion of the Route Descriptor associated with this ARP cache entry.
OCT wfleRDArpAtmAddress	1.3.6.1.4.1.18.3.5.9.5.20.9.1.3	OCTET STRING	read-only	The ATM address of the LAN Emulation Client which is associated with the route descriptor.
INT wfleRDArpEntryType	1.3.6.1.4.1.18.3.5.9.5.20.9.1.4	INTEGER	read-only	Indicates how this RD LE_ARP table entry was created and whether it is aged.
INT wfleRDArpRowStatus	1.3.6.1.4.1.18.3.5.9.5.20.9.1.5	INTEGER	read-write	Row status of enable or disable
INT wfleRDArpCct	1.3.6.1.4.1.18.3.5.9.5.20.9.1.6	INTEGER	read-only	This corresponds to the Wellfleet circuit number
INT wfleRDArpVpi	1.3.6.1.4.1.18.3.5.9.5.20.9.1.7	INTEGER	read-only	This is the Vpi will be used for this Route Descriptor
INT wfleRDArpVci	1.3.6.1.4.1.18.3.5.9.5.20.9.1.8	INTEGER	read-only	This is the Vci will be used for this Route Descriptor
wfAtmLecConfigLesTable	1.3.6.1.4.1.18.3.5.9.5.20.10		not-accessible	Address of Configured LES per LEC
wfAtmLecConfigLesEntry	1.3.6.1.4.1.18.3.5.9.5.20.10.1		not-accessible	An entry in the ATM Le Table
INT wfAtmLecConfigLesDelete	1.3.6.1.4.1.18.3.5.9.5.20.10.1.1	INTEGER	read-write	Create or Delete this LES Atm Address from the list
INT wfAtmLecConfigLesEnable	1.3.6.1.4.1.18.3.5.9.5.20.10.1.2	INTEGER	read-write	Enable or disable this LES Atm Address
INT wfAtmLecConfigLesCct	1.3.6.1.4.1.18.3.5.9.5.20.10.1.3	INTEGER	read-only	CCT number for this LEC
INT wfAtmLecConfigLesIndex	1.3.6.1.4.1.18.3.5.9.5.20.10.1.4	INTEGER	read-only	a unique one up type number to create a list
OCT wfAtmLecConfigLesAddress	1.3.6.1.4.1.18.3.5.9.5.20.10.1.5	OCTET STRING	read-write	Atm address of the LES
STR wfAtmLecConfigLesName	1.3.6.1.4.1.18.3.5.9.5.20.10.1.6	DisplayString	read-write	User name for the LES

RFC description

ATM LAN Emulation Client (LEC) configuration and operational status management for Wellfleet devices.

Start monitoring Wellfleet/Bay Networks router with ATM interfaces, legacy (LEC/ELAN join-state status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Wellfleet-ATM-LE-MIB

What Is Wellfleet-ATM-LE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description