WWP-QOS-MIB

All MIBs › WWP-QOS-MIB

Organization: World Wide Packets, Inc

Last Updated: 2001-04-03

Category: World Wide Packets Metro Ethernet

Description: Covers quality of service settings on World Wide Packets equipment, including traffic classification and scheduling policies.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is WWP-QOS-MIB?

WWP-QOS-MIB is a proprietary module from World Wide Packets (later acquired by Ciena) covering Quality of Service configuration on their Ethernet switching platforms. As indicated by its name and short description, it manages traffic classification and scheduling policy settings such as priority queues, rate limiting, and QoS profiles applied to switch ports. Because no module description text or sample objects were available for this entry, its exact object structure could not be independently confirmed, but QoS MIBs of this type are generally used to verify configuration correctness and to monitor queue-level statistics such as dropped or queued packet counts, which can reveal congestion or misconfiguration issues. It likely builds on the vendor's broader WWP enterprise MIB tree rather than standard IETF DiffServ MIBs. Deployment context is carrier Ethernet or metro-area network switches where QoS policy enforcement and verification are needed at each hop. Network engineers evaluating or troubleshooting this functionality can download the WWP-QOS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in WWP-QOS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ciena (World Wide Packets) Ethernet switches

Monitoring Examples

No sample objects were provided for this module, so specific table or object names cannot be cited; typically a QoS MIB of this kind would be polled for per-port or per-queue scheduling weights and drop counters to detect congestion, but that could not be confirmed from the available data.

What Can Be Monitored

QoS policy/profile assignment per port (unconfirmed, no sample objects available)

Imported Objects

From SNMPv2-SMI

Counter64
Integer32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION

From WWP-SMI

wwpModules

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wwpQosMIB	1.3.6.1.4.1.6141.2.12			The MIB module for the WWP QOS specific information.
wwpQosMIBObjects	1.3.6.1.4.1.6141.2.12.1
wwpQos	1.3.6.1.4.1.6141.2.12.1.1
wwpQosTable	1.3.6.1.4.1.6141.2.12.1.1.1		not-accessible	A Table of QOS per vlan per port Entries.
wwpQosEntry	1.3.6.1.4.1.6141.2.12.1.1.1.1		not-accessible	The QOS per vlan per port Entry in the Table.
VLA wwpQosVlanId	1.3.6.1.4.1.6141.2.12.1.1.1.1.1	VlanId	read-only	Vlan ID for this instance of QOS. This Vlan Id should refer to the wwpVlanId in the WwpVlanEntry.
INT wwpQosPortId	1.3.6.1.4.1.6141.2.12.1.1.1.1.2	INTEGER	read-only	Port ID for this instance of . Port ID's start at 1, and are consecutive for each additional port. This port Id should refer to the dot1dBasePort in the Dot1dBasePortEntry.
I32 wwpQosRateLimit	1.3.6.1.4.1.6141.2.12.1.1.1.1.3	Integer32	read-write	The ingress traffic rate limit to be applied for this QOS entry.
I32 wwpQosPriQueue	1.3.6.1.4.1.6141.2.12.1.1.1.1.4	Integer32	read-write	The TX-priority-queue value for this entry.
ROW wwpQosRowStatus	1.3.6.1.4.1.6141.2.12.1.1.1.1.5	RowStatus	read-create	Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'.
wwpQosStatsTable	1.3.6.1.4.1.6141.2.12.1.1.2		not-accessible	A Table of QOS Stats per vlan per port Entries.
wwpQosStatsEntry	1.3.6.1.4.1.6141.2.12.1.1.2.1		not-accessible	The QOS Stats per vlan per port Entry in the Table.
VLA wwpQosStatsVlanId	1.3.6.1.4.1.6141.2.12.1.1.2.1.1	VlanId	read-only	Vlan ID for this instance of QOS. This Vlan Id should refer to the wwpVlanId in the WwpVlanEntry.
INT wwpQosStatsPortId	1.3.6.1.4.1.6141.2.12.1.1.2.1.2	INTEGER	read-only	Port ID for this instance of . Port ID's start at 1, and are consecutive for each additional port. This port Id should refer to the dot1dBasePort in the Dot1dBasePortEntry.
C64 wwpQosRxBytes	1.3.6.1.4.1.6141.2.12.1.1.2.1.3	Counter64	read-only	The number of bytes received for this QOS Entry.
C64 wwpQosRxPkts	1.3.6.1.4.1.6141.2.12.1.1.2.1.4	Counter64	read-only	The number of pkts received for this QOS Entry.
INT wwpQosResetCounters	1.3.6.1.4.1.6141.2.12.1.1.2.1.5	INTEGER	read-write	To reset the counters related to this QOS entry. A read on this object will always return the 'none'
wwpQosPriToQMapTable	1.3.6.1.4.1.6141.2.12.1.1.3		not-accessible	A Table of mapping of an RX-priority to a TX-queue.
wwpQosPriToQMapEntry	1.3.6.1.4.1.6141.2.12.1.1.3.1		not-accessible	The mapping Entry of an RX-priority to a TX-queue in the Table.
I32 wwpQosRxPriority	1.3.6.1.4.1.6141.2.12.1.1.3.1.1	Integer32	read-only	The RX-prioroty value for this entry.
I32 wwpQosTxPriQueue	1.3.6.1.4.1.6141.2.12.1.1.3.1.2	Integer32	read-write	The TX-priority-queue value for this entry.
wwpQosPortTable	1.3.6.1.4.1.6141.2.12.1.1.4		not-accessible	A Table of QOS per port Entries.
wwpQosPortEntry	1.3.6.1.4.1.6141.2.12.1.1.4.1		not-accessible	The QOS per port Entry in the Table.
INT wwpQosPortIndex	1.3.6.1.4.1.6141.2.12.1.1.4.1.1	INTEGER	read-only	Port ID for this instance of . Port ID's start at 1, and are consecutive for each additional port. This port Id should refer to the dot1dBasePort in the Dot1dBasePortEntry.
I32 wwpQosPortPriQueue	1.3.6.1.4.1.6141.2.12.1.1.4.1.2	Integer32	read-write	The TX-priority-queue value for this entry. The protocol entry in the hardware table will have the specified TX-priority-queue value. If no priority is associated with the port, then it is set to -1.
INT wwpQosPortQAlgo	1.3.6.1.4.1.6141.2.12.1.1.4.1.3	INTEGER	read-write	The transmit queue servicing algorithm for the port. It can be either set to strict or credir(Weighted Fair Queuing).
INT wwpQosPortQApplyMode	1.3.6.1.4.1.6141.2.12.1.1.4.1.4	INTEGER	read-write	This object decides whether to apply the config of all the queues together or one at a time. If this object is set to mgmtForAllQueues , then the Agent gets the config for all the 4 queues from the wwpQosPortQConfigTable and apply the configuration to Qos manager. This object shouldn't be set to mgmtForAllQueues unless all the 4 queues have been configured with Qdepth and QWeight. If it is set to mgmtPerQueue,then the agent just get the config for each configured queue at a time and apply the config to the Qos Manager.
wwpQosPortQConfTable	1.3.6.1.4.1.6141.2.12.1.1.5		not-accessible	A Table of QOS per port per Queue Entries.
wwpQosPortQConfEntry	1.3.6.1.4.1.6141.2.12.1.1.5.1		not-accessible	The QOS per port per queue Config Entry in the Table. This config will apply to the Qos Manager depending upon the wwpQosPortQApplyMode in the wwpQosPortEntry.
INT wwpQosConfPortId	1.3.6.1.4.1.6141.2.12.1.1.5.1.1	INTEGER	read-only	Port ID for this instance of . Port ID's start at 1, and are consecutive for each additional port. This port Id should refer to the dot1dBasePort in the Dot1dBasePortEntry.
I32 wwpQosConfQueueId	1.3.6.1.4.1.6141.2.12.1.1.5.1.2	Integer32	read-only	The TX-priority-queue Id.
I32 wwpQosPortQConfWeight	1.3.6.1.4.1.6141.2.12.1.1.5.1.3	Integer32	read-write	The bandwidth servicing percentage for the specified port transmit queue. This config will apply to the Qos Manager depending upon the wwpQosPortQApplyMode in the wwpQosPortEntry.
I32 wwpQosPortQConfDepth	1.3.6.1.4.1.6141.2.12.1.1.5.1.4	Integer32	read-write	The maximum packet depth for the specified port transmit queue. The depth value corresponds to: Depth Value \| Actual Number of Packets --------------\|--------------------------- 0 \| 32 1 \| 64 2 \| 128 3 \| 256 The maximum total queue depth that can be configured for the port is a combination of depth values that would not exceed an actual packet count of 384. This config will apply to the Qos Manager depending upon the wwpQosPortQApplyMode in the wwpQosPortEntry.
ROW wwpQosPortQConfStatus	1.3.6.1.4.1.6141.2.12.1.1.5.1.5	RowStatus	read-create	The RowStatus to create the config entry. The RowStatus must be set to active for the wwpQosPortQApplyMode to be applied.
wwpQosPortQStatusTable	1.3.6.1.4.1.6141.2.12.1.1.6		not-accessible	A Table of QOS per port per Queue Entries.
wwpQosPortQStatusEntry	1.3.6.1.4.1.6141.2.12.1.1.6.1		not-accessible	The QOS per port per queue Entry in the Table.
INT wwpQosQPortId	1.3.6.1.4.1.6141.2.12.1.1.6.1.1	INTEGER	read-only	Port ID for this instance of . Port ID's start at 1, and are consecutive for each additional port. This port Id should refer to the dot1dBasePort in the Dot1dBasePortEntry.
I32 wwpQosQueueId	1.3.6.1.4.1.6141.2.12.1.1.6.1.2	Integer32	read-only	The TX-priority-queue Id.
I32 wwpQosPortQWeight	1.3.6.1.4.1.6141.2.12.1.1.6.1.3	Integer32	read-only	The current bandwidth servicing percentage for the specified port transmit queue.
I32 wwpQosPortQDepth	1.3.6.1.4.1.6141.2.12.1.1.6.1.4	Integer32	read-only	The current maximum packet depth for the specified port transmit queue.
INT wwpQosTxAssignmentMode	1.3.6.1.4.1.6141.2.12.1.1.7	INTEGER	read-write	The QoS TX-priority-queue assignment mode. This affect the behavior for ALL QoS entries. Setting the mode to useQos(0) will cause the ASIC to assign the TX-priority-queue value from the matching QoS entry to the frame. When set to useGreater(1), the ASIC will assign the greater of the two results: QoS Tx-priority or RX-Pri-To-Q TX-priority.
INT wwpQosPortTxAssignmentMode	1.3.6.1.4.1.6141.2.12.1.1.8	INTEGER	read-write	The Port Protocol TX-priority-queue assignment mode. This affect the behavior for ALL Port Protocol entries. Setting the mode to usePort(0) will cause the ASIC to assign the TX-priority-queue value from the matching Port Protocol entry to the frame. When set to useGreater(1), the ASIC will assign the greater of the two results: Port Protocol Tx-priority or RX-Pri-To-Q TX-priority.
wwpQosNotificationPrefix	1.3.6.1.4.1.6141.2.12.2
wwpQosNotifications	1.3.6.1.4.1.6141.2.12.2.0
wwpQosMIBConformance	1.3.6.1.4.1.6141.2.12.3
wwpQosMIBCompliances	1.3.6.1.4.1.6141.2.12.3.1
wwpQosMIBGroups	1.3.6.1.4.1.6141.2.12.3.2

RFC description

Manages World Wide Packets quality of service configuration including traffic classification and scheduling policies.

Start monitoring Ciena (World Wide Packets) Ethernet switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download WWP-QOS-MIB

What Is WWP-QOS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description