WWP-LEOS-EXT-LAG-MIB

All MIBs › WWP-LEOS-EXT-LAG-MIB

Organization: Ciena, Inc

Last Updated: 2003-01-15

Category: Ciena LEOS Carrier Ethernet

Description: Manages Ciena LEOS extended Link Aggregation Group configuration, member port status, and LACP parameters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is WWP-LEOS-EXT-LAG-MIB?

WWP-LEOS-EXT-LAG-MIB is a Ciena (World Wide Packets, LEOS platform) proprietary MIB extending the standard IEEE 802.3ad LAG MIB with aggregator creation/deletion management. Its objects cover maximum and current LAG counts, and an extended LAG table recording aggregator ID/name/index, status, mode, protection-revert state/timer, hash mode, protection mode, and flood-hash mode, alongside a per-physical-port LAG-mode table (admin/operational mode) and a protection table (protected port, row status). As a configuration/status MIB it lets an administrator confirm a LAG's protection-revert timer and hash mode, and audit which physical ports are configured for LAG protection. It is deployed on Ciena (World Wide Packets LEOS) carrier Ethernet switches. Engineers can download the WWP-LEOS-EXT-LAG-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in WWP-LEOS-EXT-LAG-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ciena (World Wide Packets LEOS) carrier Ethernet switches

Monitoring Examples

An administrator checks wwpLeosExtLagProtectionRevertTimer to confirm how long a LAG will wait before reverting to its primary member after a protection switchover on a Ciena LEOS switch.

What Can Be Monitored

LAG aggregator creation, protection mode, and revert timer

Imported Objects

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus

From WWP-SMI

wwpModulesLeos

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wwpLeosExtLagMIB	1.3.6.1.4.1.6141.2.60.14			This MIB module is an extension to the IEEE8023-LAG-mib. This MIB defines the managed objects for the creation and deletion of Aggregators.
wwpLeosExtLagMIBObjects	1.3.6.1.4.1.6141.2.60.14.1
wwpLeosExtLag	1.3.6.1.4.1.6141.2.60.14.1.1
U32 wwpLeosMaxLags	1.3.6.1.4.1.6141.2.60.14.1.1.1	Unsigned32	read-only	The maximum number of aggregators that this device supports.
U32 wwpLeosNumLags	1.3.6.1.4.1.6141.2.60.14.1.1.2	Unsigned32	read-only	The current number of LAGs that are configured in this device.
wwpLeosExtLagTable	1.3.6.1.4.1.6141.2.60.14.1.1.3		not-accessible	The (conceptual) table listing all the aggregators.
wwpLeosExtLagEntry	1.3.6.1.4.1.6141.2.60.14.1.1.3.1		not-accessible	An entry (conceptual row) in the wwpLeosExtLagTable.
I32 wwpLeosExtAggId	1.3.6.1.4.1.6141.2.60.14.1.1.3.1.1	Integer32	read-only	Object which specifies a unique entry in the wwpLeosExtLagTable. A management station wishing to create a LAG should use a pseudo-random value for this object when creating an instance of a wwpLeosExtLagEntry.
STR wwpLeosExtAggName	1.3.6.1.4.1.6141.2.60.14.1.1.3.1.2	DisplayString	read-create	The name assigned to this Lag by the Management station. This object can only be set while creating LAG. It is not allowed to rename the LAG name once it is created.
I32 wwpLeosExtAggIndex	1.3.6.1.4.1.6141.2.60.14.1.1.3.1.3	Integer32	read-only	The unique identifier allocated to this Aggregator by the local System. This attribute identifies an Aggregator instance among the subordinate managed objects of the containing object. This value is read-only. This object refer to the dot3adAggIndex in the IEEE-8023-LAG-MIB.
ROW wwpLeosExtAggStatus	1.3.6.1.4.1.6141.2.60.14.1.1.3.1.4	RowStatus	read-create	Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To disable the aggregator, a management should set this object to 'notInService'.
INT wwpLeosExtAggMode	1.3.6.1.4.1.6141.2.60.14.1.1.3.1.5	INTEGER	read-write	This object specifies the mode in which given aggregation is operating.
INT wwpLeosExtLagProtectionRevertState	1.3.6.1.4.1.6141.2.60.14.1.1.3.1.6	INTEGER	read-write	This object specifies that if the primary port goes from operationally disabled to operationally enabled it shall become active, and one of the secondary ports shall become backup if this MIB object is set to 'on' and the wwpLeosLagProtectionRevertTimer timer expires.
INT wwpLeosExtLagProtectionRevertTimer	1.3.6.1.4.1.6141.2.60.14.1.1.3.1.7	INTEGER	read-write	This object specifies the revert protection timer value.
INT wwpLeosExtAggHashMode	1.3.6.1.4.1.6141.2.60.14.1.1.3.1.8	INTEGER	read-write	This object specifies the hash mode used by the aggregation for known unicast frames.
INT wwpLeosExtLagProtectionMode	1.3.6.1.4.1.6141.2.60.14.1.1.3.1.9	INTEGER	read-write	This object specifies the LACP protection-mode in which given aggregation is operating.
wwpLeosLagModeTable	1.3.6.1.4.1.6141.2.60.14.1.1.4		not-accessible	The (conceptual) table listing the modes of aggregation on each port.
wwpLeosLagModeEntry	1.3.6.1.4.1.6141.2.60.14.1.1.4.1		not-accessible	An entry (conceptual row) in the wwpLeosLagModeTable.
INT wwpLeosLagPhyPortId	1.3.6.1.4.1.6141.2.60.14.1.1.4.1.1	INTEGER	read-only	This object specifies the physical port number. It is also used as index in the table.
INT wwpLeosLagAdminMode	1.3.6.1.4.1.6141.2.60.14.1.1.4.1.2	INTEGER	read-write	This object specifies the administrative mode in which given port is operating.
INT wwpLeosLagOperMode	1.3.6.1.4.1.6141.2.60.14.1.1.4.1.3	INTEGER	read-only	This object specifies the operation mode in which given port is operating.
wwpLeosLagProtectionTable	1.3.6.1.4.1.6141.2.60.14.1.1.5		not-accessible	The (conceptual) table listing the protection ports for each aggregation.
wwpLeosLagProtectionEntry	1.3.6.1.4.1.6141.2.60.14.1.1.5.1		not-accessible	An entry (conceptual row) in the wwpLeosLagProtectionTable.
INT wwpLeosLagProtectionPort	1.3.6.1.4.1.6141.2.60.14.1.1.5.1.1	INTEGER	read-only	This object specifies the protection port number. It is also used as index in the table.
ROW wwpLeosLagProtectionRowStatus	1.3.6.1.4.1.6141.2.60.14.1.1.5.1.2	RowStatus	read-create	Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete entry set this object to 'destroy'.
INT wwpLeosExtAggFloodHashMode	1.3.6.1.4.1.6141.2.60.14.1.1.6	INTEGER	read-write	This object specifies the aggregation hash mode used by unknown unicast, multicast and broadcast frames for all aggregation ports in the system.
wwpLeosExtLagMIBNotificationPrefix	1.3.6.1.4.1.6141.2.60.14.2
wwpLeosExtLagMIBNotifications	1.3.6.1.4.1.6141.2.60.14.2.0
wwpLeosExtLagMIBConformance	1.3.6.1.4.1.6141.2.60.14.3
wwpLeosExtLagMIBCompliances	1.3.6.1.4.1.6141.2.60.14.3.1
wwpLeosExtLagMIBGroups	1.3.6.1.4.1.6141.2.60.14.3.2

RFC description

Extends IEEE 802.3 LAG MIB with creation and deletion of link aggregators on Ciena LEOS switches.

Start monitoring Ciena (World Wide Packets LEOS) carrier Ethernet switches (LAG protection-revert/hash-mode config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download WWP-LEOS-EXT-LAG-MIB

What Is WWP-LEOS-EXT-LAG-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description