All MIBs › WS-CC-RF-MIB
Organization: Symbol Technologies, Inc
Last Updated: 2008-10-21
Category: Symbol Technologies Wireless
Description: Manages Symbol Technologies wireless controller RF domain configuration and radio frequency channel parameters.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is WS-CC-RF-MIB?
WS-CC-RF-MIB is a Symbol Technologies module covering RF (radio frequency) domain configuration for the vendor's wireless controller/switch product line, managing radio channel and RF-related parameters across the controlled access points. It exposes RF domain configuration data such as channel assignments and power/RF parameters used to coordinate radio behavior across a fleet of access points. Its monitoring relevance is primarily configuration/status oriented for the wireless RF layer -- confirming channel and RF settings are applied correctly across the domain -- which is a software-level indicator of wireless service health rather than a hardware sensor. No specific dependency on other MIBs is apparent from the minimal module description. It is deployed on Symbol Technologies (later Motorola/Zebra) wireless controllers managing RF domains across enterprise Wi-Fi access point deployments, and administrators can perform a WS-CC-RF-MIB download to load the module directly into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in WS-CC-RF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Symbol Technologies wireless LAN controller
Monitoring Examples
No sample object or table names were extracted for this module, so specific identifiers cannot be cited; an administrator would typically poll RF domain channel and power configuration objects to confirm the wireless controller has applied consistent RF settings across its access points and to detect a misconfigured or conflicting channel assignment. Without a verified object list, further technical detail would not be grounded in the actual MIB content.
What Can Be Monitored
- RF domain configuration
- radio channel assignments
- RF power parameters
This MIB depends on
Related MIBs
Imported Objects
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| TimeTicks | |
| Unsigned32 |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| PhysAddress | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
From WS-CC-SMI
| wsCcRf | OBJECT-IDENTITY |
From WS-TYPE-MIB
| DoActionNow | |
| MultiPointer256 | |
| MultiPointer64 |
How to Use in IPNetwork Monitor
Example using wsCcRfRapStatusSignalCount OID:
Select a Symbol Technologies wireless LAN controller (RF-domain channel/power config status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type wsCcRfRapStatusSignalCount into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the number of signal data points for this radio. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| wsCcRfMIB | 1.3.6.1.4.1.388.14.3.2.1 | Mib for wireless features | ||
| STR wsCcRfCountryCode | 1.3.6.1.4.1.388.14.3.2.1.1 | DisplayString | read-write | This value is a two-character representation of the country code. Note: when changing this _CountrySelection, the current channel and power levels are NOT changed. The prior settings for these values may or may not be valid/legal for the new country selected. It is up to the network management software to ensure that channel and/or power settings are changed BEFORE changing the country selection so that no such invalid/illegal state is reached, even for a short interim. country code: Argentina: ar Australia: au Austria: at Bahrain: bh Belarus: by Belgium: be Brazil: br Bulgaria: bg Canada: ca Chile: cl China: cn Colombia: co Costa Rica: cr Croatia: hr Czech Republic: cz Denmark: dk Ecuador: ec Egypt: eg Estonia: ee Finland: fi France: fr Germany: de Greece: gr Hong Kong: hk Hungary: hu Iceland: is India: in Indonesia: id Ireland: ie Israel: il Italy: it Japan(J52): jj Japan(W52/W53): jw Jordan: jo Kazakhstan: kz Kuwait: kw Latvia: lv Liechtenstein: li Lithuania: lt Luxembourg: lu Malaysia: my Mexico: mx Morocco: ma Netherlands: nl New Zealand: nz Norway: no Oman: om Peru: pe Philippines: ph Poland: pl Portugal: pt Qatar: qa Romania: ro Russia: ru Saudi Arabia: sa Singapore: sg Slovak Republic: sk Slovenia: si South Africa: za South Korea: kr Spain: es Sri Lanka: lk Sweden: se Switzerland: ch Taiwan: tw Thailand: th Turkey: tr Ukraine: ua United Arab Emirates: ae United Kingdom: uk United States: us Uruguay: uy Venezuela: ve Vietnam: vn |
| INT wsCcRfSnmpSetDelay | 1.3.6.1.4.1.388.14.3.2.1.2 | INTEGER | read-write | NOT Implemented in this release: this would cause any configuration change to be held in a cache until this variable is toggled again. It will be useful if we need to apply some changes in a batch-mode. |
| U32 wsCcRfClusterIndex | 1.3.6.1.4.1.388.14.3.2.1.3 | Unsigned32 | read-write | The cluster index of the switch. |
| T/F wsCcRfProxyRespMuArpReq | 1.3.6.1.4.1.388.14.3.2.1.4 | TruthValue | read-write | Causes the switch to respond to an ARP Request on behalf of an MU. Since a lot of traffic is ARP, this helps to save battery life on the MUs. |
| T/F wsCcRfOversizedFrameEnable | 1.3.6.1.4.1.388.14.3.2.1.5 | TruthValue | read-write | Enable over-sized frame. |
| T/F wsCcRfWlanPriorityEnable | 1.3.6.1.4.1.388.14.3.2.1.6 | TruthValue | read-write | Use wlan priority weights to determine packet queueing order. |
| INT wsCcRfAdvancedConfigEnable | 1.3.6.1.4.1.388.14.3.2.1.7 | INTEGER | read-write | Enable or disable Advanced-Config functionality on the switch. Disabling of Advanced-Config will fail when the current setting is not compatible with Auto-Config rules. If user wishes to force the disable action, he/she should use the forcedFalse option instead. Note: After setting with forcedFalse, the object will return false(2) on a snmp-get. |
| STR wsCcRfLastError | 1.3.6.1.4.1.388.14.3.2.1.8 | DisplayString | read-only | Error string of the last failed attempt snmp set |
| wsCcRfAp | 1.3.6.1.4.1.388.14.3.2.1.9 | |||
| I32 wsCcRfApCount | 1.3.6.1.4.1.388.14.3.2.1.9.1 | Integer32 | read-only | Number of Acess Ports adopted |
| wsCcRfApTable | 1.3.6.1.4.1.388.14.3.2.1.9.2 | not-accessible | This table lists all Access Ports that contain at least one radio that has been adopted by this wireless switch | |
| wsCcRfApEntry | 1.3.6.1.4.1.388.14.3.2.1.9.2.1 | not-accessible | ||
| INT wsCcRfApIndex | 1.3.6.1.4.1.388.14.3.2.1.9.2.1.1 | INTEGER | accessible-for-notify | Small, arbitrary integer index. |
| PHY wsCcRfApNicMac | 1.3.6.1.4.1.388.14.3.2.1.9.2.1.2 | PhysAddress | read-only | MAC address of this Access Port. |
| STR wsCcRfApModelNumber | 1.3.6.1.4.1.388.14.3.2.1.9.2.1.3 | DisplayString | read-only | Model number of the Access Port. |
| STR wsCcRfApSerialNumber | 1.3.6.1.4.1.388.14.3.2.1.9.2.1.4 | DisplayString | read-only | Serial Number of this Access Port. |
| STR wsCcRfApPcbRevision | 1.3.6.1.4.1.388.14.3.2.1.9.2.1.5 | DisplayString | read-only | Revision of the printed circuit board for this Access Port. |
| STR wsCcRfApBootLoaderRev | 1.3.6.1.4.1.388.14.3.2.1.9.2.1.6 | DisplayString | read-only | Revision of the boot loader code in this Access Port. |
| STR wsCcRfApWispVersion | 1.3.6.1.4.1.388.14.3.2.1.9.2.1.7 | DisplayString | read-only | Version of the WISP (AP-switch) protocol implemented by this Access Port. |
| STR wsCcRfApRuntimeFwVersion | 1.3.6.1.4.1.388.14.3.2.1.9.2.1.8 | DisplayString | read-only | Version of run-time code on this Access Port. |
| U32 wsCcRfApNumRadios | 1.3.6.1.4.1.388.14.3.2.1.9.2.1.9 | Unsigned32 | read-only | The number of radios implemented on this Access Port. |
| I32 wsCcRfApRadio1 | 1.3.6.1.4.1.388.14.3.2.1.9.2.1.10 | Integer32 | read-only | Index of the first radio. 0 will be returned if the radio is not adopted. |
| I32 wsCcRfApRadio2 | 1.3.6.1.4.1.388.14.3.2.1.9.2.1.11 | Integer32 | read-only | Index of the second radio. 0 will be returned if the radio is not adopted. |
| IP wsCcRfApAddress | 1.3.6.1.4.1.388.14.3.2.1.9.2.1.12 | IpAddress | read-only | The IP address of the L3 AP. This field is empty for L2 AP. |
| U32 wsCcRfApVoiceDelay | 1.3.6.1.4.1.388.14.3.2.1.9.2.1.13 | Unsigned32 | read-only | Delay to AP (round trip delay / 2) for voice packets in ms. A value of 0 for this object implies that round trip delay is unavailable. |
| wsCcRfApImageVersionTable | 1.3.6.1.4.1.388.14.3.2.1.9.3 | not-accessible | Table displaying Access Ports image version info. | |
| wsCcRfApImageVersionEntry | 1.3.6.1.4.1.388.14.3.2.1.9.3.1 | not-accessible | ||
| I32 wsCcRfApImageVersionIndex | 1.3.6.1.4.1.388.14.3.2.1.9.3.1.1 | Integer32 | accessible-for-notify | Simple index. |
| APT wsCcRfApImageVersionApType | 1.3.6.1.4.1.388.14.3.2.1.9.3.1.2 | ApType | read-only | Ap type that the image applies to. |
| STR wsCcRfApImageVersionModel | 1.3.6.1.4.1.388.14.3.2.1.9.3.1.3 | DisplayString | read-only | Model string of the Access Port image. |
| STR wsCcRfApImageVersionName | 1.3.6.1.4.1.388.14.3.2.1.9.3.1.4 | DisplayString | read-only | Version name of the Access Port image. |
| STR wsCcRfApImageVersionReleaseDate | 1.3.6.1.4.1.388.14.3.2.1.9.3.1.5 | DisplayString | read-only | Release date of the Access Port image. |
| I32 wsCcRfApImageVersionImageSize | 1.3.6.1.4.1.388.14.3.2.1.9.3.1.6 | Integer32 | read-only | Size in bytes of the Access Port image. |
| wsCcRfApUnadoptedTable | 1.3.6.1.4.1.388.14.3.2.1.9.4 | not-accessible | Table of detected but unadopted access ports. | |
| wsCcRfApUnadoptedEntry | 1.3.6.1.4.1.388.14.3.2.1.9.4.1 | not-accessible | ||
| I32 wsCcRfApUnadoptedIndex | 1.3.6.1.4.1.388.14.3.2.1.9.4.1.1 | Integer32 | accessible-for-notify | Simple index. |
| PHY wsCcRfApUnadoptedMac | 1.3.6.1.4.1.388.14.3.2.1.9.4.1.2 | PhysAddress | read-only | Mac address of detected but unadopted AP. |
| APT wsCcRfApUnadoptedApType | 1.3.6.1.4.1.388.14.3.2.1.9.4.1.3 | ApType | read-only | Ap type of detected but unadopted access port. |
| U32 wsCcRfApUnadoptedLastSeen | 1.3.6.1.4.1.388.14.3.2.1.9.4.1.4 | Unsigned32 | read-only | The unadopted-ap was last seen wsCcRfApUnadoptedLastSeen seconds ago. |
| wsCcRfApHistoryTable | 1.3.6.1.4.1.388.14.3.2.1.9.5 | not-accessible | Description. | |
| wsCcRfApHistoryEntry | 1.3.6.1.4.1.388.14.3.2.1.9.5.1 | not-accessible | Description. | |
| INT wsCcRfApHistoryIndex | 1.3.6.1.4.1.388.14.3.2.1.9.5.1.1 | INTEGER | read-only | Simple Index |
| PHY wsCcRfApHistoryMac | 1.3.6.1.4.1.388.14.3.2.1.9.5.1.2 | PhysAddress | read-only | MAC Address of the AP |
| INT wsCcRfApHistoryRadioType | 1.3.6.1.4.1.388.14.3.2.1.9.5.1.3 | INTEGER | read-only | Radio Type: 11a, 11b, 11g, 11an, 11bgn or N/A |
| STR wsCcRfApHistoryTimestamp | 1.3.6.1.4.1.388.14.3.2.1.9.5.1.4 | DisplayString | read-only | Date and Time |
| INT wsCcRfApHistoryEvent | 1.3.6.1.4.1.388.14.3.2.1.9.5.1.5 | INTEGER | read-only | Adoption/unadoption/self-healing event |
| STR wsCcRfApHistoryReason | 1.3.6.1.4.1.388.14.3.2.1.9.5.1.6 | DisplayString | read-only | AP History reason for occurence of event |
| INT wsCcRfApHistoryEnable | 1.3.6.1.4.1.388.14.3.2.1.9.6 | INTEGER | read-write | Enable / disable AP history data collection |
| T/F wsCcRfApHistoryClear | 1.3.6.1.4.1.388.14.3.2.1.9.7 | TruthValue | read-write | Clears the entries in the AP History table. |
| wsCcRfApAapVersionTable | 1.3.6.1.4.1.388.14.3.2.1.9.8 | not-accessible | A table of the supported AAP firmware versions. | |
| wsCcRfApAapVersionEntry | 1.3.6.1.4.1.388.14.3.2.1.9.8.1 | not-accessible | Entry in AAP firmware version table. | |
| INT wsCcRfApAapVersionType | 1.3.6.1.4.1.388.14.3.2.1.9.8.1.1 | INTEGER | read-only | AAP Type |
| STR wsCcRfApAapVersionString | 1.3.6.1.4.1.388.14.3.2.1.9.8.1.2 | DisplayString | read-write | AAP minimum firmware version required. The string should be of the format is X.X.X.X-XXXR. |
| wsCcRfApImgUploadTable | 1.3.6.1.4.1.388.14.3.2.1.9.9 | not-accessible | Table to upload new AP images. | |
| wsCcRfApImgUploadEntry | 1.3.6.1.4.1.388.14.3.2.1.9.9.1 | not-accessible | An entry in the table. | |
| INT wsCcRfApImgUploadImgType | 1.3.6.1.4.1.388.14.3.2.1.9.9.1.1 | INTEGER | read-only | Image type. |
| STR wsCcRfApImgUploadFile | 1.3.6.1.4.1.388.14.3.2.1.9.9.1.2 | DisplayString | read-create | Image file path. It can be specified as one of the following: flash:/path/file cf:/path/file usb1:/path/file usb2:/path/file |
| ABB wsCcRfApImgUploadRowStatus | 1.3.6.1.4.1.388.14.3.2.1.9.9.1.3 | AbbrevRowStatus | read-create | The Row status. All columns must be supplied to create a row. Row creation uploads the file to the Switch. If upload fails, row creation will fail and wsCcRfApImgUploadLastFailedReason will have the reason. Row deletion restores the original AP Image. In case AAP, the image is not uploaded to the switch. AAP image update will fetch the image from the specified location. |
| STR wsCcRfApImgUploadLastFailedReason | 1.3.6.1.4.1.388.14.3.2.1.9.10 | DisplayString | read-only | Last image upload failed reason. |
| wsCcRfApAapImg | 1.3.6.1.4.1.388.14.3.2.1.9.11 | |||
| T/F wsCcRfApAapImgEnableAutoUpd | 1.3.6.1.4.1.388.14.3.2.1.9.11.1 | TruthValue | read-write | Enable or disable automatic image update of AAP. The value of this object can be set to 'true' even if no images have previously been configured in wsCcRfApImgUploadTable. |
| wsCcRfApAapImgUpd | 1.3.6.1.4.1.388.14.3.2.1.9.11.2 | |||
| PHY wsCcRfApAapImgUpdMac | 1.3.6.1.4.1.388.14.3.2.1.9.11.2.1 | PhysAddress | read-write | MAC address of the AAP. |
| INT wsCcRfApAapImgUpdStart | 1.3.6.1.4.1.388.14.3.2.1.9.11.2.2 | INTEGER | read-write | Image update start. Setting this value to 2 means starting image update. The following must be configured before setting this value to 2: - wsCcRfApAapImgUpdMac contains the MAC address of the AAP and the AAP must be adopted. - wsCcRfApImgUploadTable contains the AAP image name. If image update fails, wsCcRfApAapImgUpdLastFailedReason will have the reason. If there is no image update, its value will be set to 1. |
| STR wsCcRfApAapImgUpdLastFailedReason | 1.3.6.1.4.1.388.14.3.2.1.9.11.2.3 | DisplayString | read-only | Last image update failed reason. |
| wsCcRfRadio | 1.3.6.1.4.1.388.14.3.2.1.11 | |||
| T/F wsCcRfRadioAutoAdopt | 1.3.6.1.4.1.388.14.3.2.1.11.1 | TruthValue | read-write | Enable or disable the switch to auto-adopt radios. |
| U32 wsCcRfRadioCnt | 1.3.6.1.4.1.388.14.3.2.1.11.2 | Unsigned32 | read-only | Number of radios adopted by the switch. This is a count of the number of rows in wsCcRfRadioStatusTable |
| PHY wsCcRfRadioLastMac | 1.3.6.1.4.1.388.14.3.2.1.11.3 | PhysAddress | read-only | This scalar records the MAC address of the most recent radio to be Adopted, UnAdopted, or Denied. |
| STR wsCcRfRadioLastReason | 1.3.6.1.4.1.388.14.3.2.1.11.4 | DisplayString | read-only | This value notes the reason for the most-recent radio UnAdoption or Denial. |
| wsCcRfRadioTable | 1.3.6.1.4.1.388.14.3.2.1.11.5 | not-accessible | This table lists all radios adopted by this wireless switch. | |
| wsCcRfRadioEntry | 1.3.6.1.4.1.388.14.3.2.1.11.5.1 | not-accessible | ||
| I32 wsCcRfRadioIndex | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.1 | Integer32 | accessible-for-notify | Small, arbitrary integer index. |
| PHY wsCcRfRadioApMac | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.2 | PhysAddress | read-create | MAC address of the Access Port that this radio resides within. |
| STR wsCcRfRadioDescr | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.3 | DisplayString | read-create | Description of the radio. |
| RAD wsCcRfRadioType | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.4 | RadioType | read-create | Radio model. Changing this value will result in all parameters getting defaulted for this radio. |
| APT wsCcRfRadioApType | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.5 | ApType | read-create | Model of the Access Port this radio resides in. |
| OCT wsCcRfRadioBssWlanMap | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.6 | OCTET STRING | read-create | The mapping of WLANs to BSSIDs. Each radio supports 4 BSSIDs and 16 WLANs. The user can map any number of WLANs to each of the BSSIDs. Each BSSID forms a virtual ap. |
| INT wsCcRfRadioAntDiversity | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.7 | INTEGER | read-create | The antenna diversity setting for the Access Port. Options for 11n radio: - Valid options are primaryOnly and mimo - Default option is mimo - For single antenna operation set mode to primaryOnly |
| T/F wsCcRfRadioShortPreamble | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.8 | TruthValue | read-create | Enable support for Short Preamble when MUs associate with the Access Port. Enabling Short Preamble may cause incompatibility with some older clients. Applies only to b/g radios. |
| I32 wsCcRfRadioRtsThresh | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.9 | Integer32 | read-create | The Request To Send(RTS) threshold(in bytes) for use by this radio. |
| I32 wsCcRfRadioBeaconInt | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.10 | Integer32 | read-create | Specify a beacon interval in units of 1,000 microseconds (K-us). This is a multiple of the DTIM (wsCcRfRadioDtimPrd) value, for example, 100 : 10. |
| I32 wsCcRfRadioDtimPrd | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.11 | Integer32 | read-create | Specify a period for the Delivery Traffic Indication Message (DTIM). This is a divisor of the beacon interval (in milliseconds), for example, 10 : 100. |
| TRA wsCcRfRadioBasicRates | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.12 | TransmitRate | read-create | List of basic rates for the radio. |
| TRA wsCcRfRadioSupportedRates | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.13 | TransmitRate | read-create | List of supported rates for the radio. |
| T/F wsCcRfRadioRapDetector | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.14 | TruthValue | read-create | If this radio is a Rogue AP detector. |
| U32 wsCcRfRadioClusterIndex | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.15 | Unsigned32 | read-create | The preferred group of Cluster |
| U32 wsCcRfRadioMaxMu | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.16 | Unsigned32 | read-create | Max number of Mu a radio can associate. |
| INT wsCcRfRadioSelfHealingAction | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.17 | INTEGER | read-create | Action taken by this radio when neighbor radios go down |
| U32 wsCcRfRadioSelfHealingPwrOffset | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.18 | Unsigned32 | read-create | Self-healing power offset for this radio |
| DOA wsCcRfRadioRunAcsNow | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.19 | DoActionNow | read-create | Set wsCcRfRadioRunAcsNow to 1 to run Acs. |
| DOA wsCcRfRadioResetParentAp | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.20 | DoActionNow | read-create | Set wsCcRfRadioResetParentAp to 1 to reset the parent Access Port of this radio. |
| DOA wsCcRfRadioReset | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.21 | DoActionNow | read-create | Set wsCcRfRadioReset to 1 to reset the Radio. |
| ROW wsCcRfRadioRowStatus | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.22 | RowStatus | read-create | Rows status of the wsCcRfRadioTable |
| INT wsCcRfRadioCcaLevel | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.23 | INTEGER | read-create | Description. |
| INT wsCcRfRadioCcaMode | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.24 | INTEGER | read-create | Description. |
| T/F wsCcRfRadioRapSingleChannelScan | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.25 | TruthValue | read-create | Enable or disable single-channel scan for Rogue AP. |
| OCT wsCcRfRadioBssDtim | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.26 | OCTET STRING | read-create | Set DTIM per BSS. DTIM period is not configurable on a per BSS basis for AP71X1 11n radios. These radios use a single DTIM period across all BSS in a radio which can be configured in wsCcRfRadioDtimPrd. |
| INT wsCcRfRadioCfgMethod | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.27 | INTEGER | read-only | The radio can be configured by user before being adopted or by the switch while adoption |
| T/F wsCcRfRadioMuLocationingEnable | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.28 | TruthValue | read-create | Enable/Disable MU locationing on this radio |
| T/F wsCcRfRadioRogueApLocationingEnable | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.29 | TruthValue | read-create | Enable/Disable rogue AP locationing on this radio |
| T/F wsCcRfRadioRssEnable | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.31 | TruthValue | read-create | Setting this object to True enables (False for disable) RSS (Remote Site Survivability) for this radio. |
| INT wsCcRfRadioGroupId | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.32 | INTEGER | read-create | The group id that this radio belongs to. This field is used for the load-balancing feature wherein radios are combined in groups and MUs are discouraged from association if it not coming from the least loaded radio in the group. Group id 0 is used to indicate that this radio does not belong to any group. |
| INT wsCcRfRadioLedMode | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.33 | INTEGER | read-create | The mode of operation of the LEDs on the AP. The meanings of the values are: startFlashing - When the value startFlashing is written to this object, the parent AP of the radio begins flashing its LEDs to help locate it. stopFlashing- When the value stopFlashing is written to this object, the parent AP of the radio reverts its LEDs to normal mode of operation. idleState - When the value idleState is written to this object, no action is taken. When read, this object always returns the value idleState. |
| INT wsCcRfRadioState | 1.3.6.1.4.1.388.14.3.2.1.11.5.1.34 | INTEGER | read-only | The state of the radio. unseen : Configured, but not connected unadopted : Connected, but not adopted normal : Adopted and working normal detector : Adopted and is working as a detector selfHealing : Legacy self-healing rescuing : Adopted and is rescuing to recover for neighbor filling : Adopted and is filling in to recover coverage hole sensor : Sensor |
| wsCcRfRadioChannelPowerTable | 1.3.6.1.4.1.388.14.3.2.1.11.6 | not-accessible | Use wsCcRfRadioChannelPower table to view and set the channel/power/placement properties of the radios. The process can be broken down into the following steps: 1. Set wsCcRfRadioCpReset to TRUE. 2. Set wsCcRfRadioCpPlacement 3. Get wsCcRfRadioCpPosChannel 4. Set wsCcRfRadioCpDesChannel 5. Get wsCcRfRadioCpPosPowerLevel 6. Set wsCcRfRadioCpDesPowerLevel 7. Get wsCcRfRadioCpPowerInMW 8. Set wsCcRfRadioCp11nChannelWidth 9. Set wsCcRfRadioCp11nSecondaryChannel 10. Set wsCcRfRadioCpSet | |
| wsCcRfRadioChannelPowerEntry | 1.3.6.1.4.1.388.14.3.2.1.11.6.1 | not-accessible | ||
| INT wsCcRfRadioCpPlacement | 1.3.6.1.4.1.388.14.3.2.1.11.6.1.1 | INTEGER | read-write | The placement for radio. |
| INT wsCcRfRadioCpChannelMode | 1.3.6.1.4.1.388.14.3.2.1.11.6.1.2 | INTEGER | read-write | fixed mode: apply user selected channel random mode: random channel selection acs mode: auto channel selection (radio will scan for the least congested channel at startup or reconfiguration) |
| NUM wsCcRfRadioCpPosChannel | 1.3.6.1.4.1.388.14.3.2.1.11.6.1.3 | MultiPointer64 | read-only | The possible channels that can be set when placement = wsCcRfRadioCpPlacement. |
| U32 wsCcRfRadioCpDesChannel | 1.3.6.1.4.1.388.14.3.2.1.11.6.1.4 | Unsigned32 | read-write | The desired channel for radio. |
| I32 wsCcRfRadioCpPosPowerDb | 1.3.6.1.4.1.388.14.3.2.1.11.6.1.5 | Integer32 | read-only | The max possible power level (dBm) that can be set when channel= wsCcRfRadioCpDesChannel. |
| I32 wsCcRfRadioCpDesPowerDb | 1.3.6.1.4.1.388.14.3.2.1.11.6.1.6 | Integer32 | read-write | The desired power level (dBm) for radio. |
| I32 wsCcRfRadioCpDesPowerMw | 1.3.6.1.4.1.388.14.3.2.1.11.6.1.7 | Integer32 | read-only | wsCcRfRadioCpDesPowerLevel in mW. |
| DOA wsCcRfRadioCpSet | 1.3.6.1.4.1.388.14.3.2.1.11.6.1.8 | DoActionShowProgress | read-write | Validate values in wsCcRfRadioCpDes fields. If it is a valid combination, configure the switch with this combination and set wsCcRfRadioCp_ to these values. |
| DOA wsCcRfRadioCpReset | 1.3.6.1.4.1.388.14.3.2.1.11.6.1.9 | DoActionShowProgress | read-write | Reset the following OIDs. wsCcRfRadioCpDesPlacement wsCcRfRadioCpDesChannel wsCcRfRadioCpDesPowerLevel wsCcRfRadioCpPosChannel wsCcRfRadioCpPosPowerLevel wsCcRfRadioCpPowerInMW wsCcRfRadioCp11nChannelWidth wsCcRfRadioCp11nSecondaryChannel |
| wsCcRfRadioWmmTable | 1.3.6.1.4.1.388.14.3.2.1.11.7 | not-accessible | Configuration parameters for 802.11e / Wireless MultiMedia, which control the Quality of Service between the wireless devices on the network | |
| wsCcRfRadioWmmEntry | 1.3.6.1.4.1.388.14.3.2.1.11.7.1 | not-accessible | ||
| RAD wsCcRfRadioWmmBeParm | 1.3.6.1.4.1.388.14.3.2.1.11.7.1.1 | RadioWmmConfig | read-write | Parameters for the Best Effort QoS category of traffic in an 802.11e network. Prior to setting this field, please be sure to get the current value. |
| RAD wsCcRfRadioWmmBkParm | 1.3.6.1.4.1.388.14.3.2.1.11.7.1.2 | RadioWmmConfig | read-write | Parameters for the Background QoS category of traffic in an 802.11e network. Prior to setting this field, please be sure to get the current value. |
| RAD wsCcRfRadioWmmViParm | 1.3.6.1.4.1.388.14.3.2.1.11.7.1.3 | RadioWmmConfig | read-write | Parameters for the Video QoS category of traffic in an 802.11e network. Prior to setting this field, please be sure to get the current value. |
| RAD wsCcRfRadioWmmVoParm | 1.3.6.1.4.1.388.14.3.2.1.11.7.1.4 | RadioWmmConfig | read-write | Parameters for the Voice QoS category of traffic in an 802.11e network. Prior to setting this field, please be sure to get the current value. |
| wsCcRfRadioDefaultTable | 1.3.6.1.4.1.388.14.3.2.1.11.8 | not-accessible | This table lists the default setting for all supported radio for this switch. Please refer to wsCcRfRadioTable for column descriptions. | |
| wsCcRfRadioDefaultEntry | 1.3.6.1.4.1.388.14.3.2.1.11.8.1 | not-accessible | ||
| I32 wsCcRfRadioDefaultIndex | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.1 | Integer32 | accessible-for-notify | |
| RAD wsCcRfRadioDefaultType | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.2 | RadioType | read-only | |
| APT wsCcRfRadioDefaultApType | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.3 | ApType | read-only | |
| OCT wsCcRfRadioDefaultBssWlanMap | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.4 | OCTET STRING | read-write | |
| INT wsCcRfRadioDefaultAntDiversity | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.5 | INTEGER | read-write | |
| T/F wsCcRfRadioDefaultShortPreamble | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.6 | TruthValue | read-write | |
| I32 wsCcRfRadioDefaultRtsThresh | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.7 | Integer32 | read-write | |
| I32 wsCcRfRadioDefaultBeaconInt | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.8 | Integer32 | read-write | |
| I32 wsCcRfRadioDefaultDtimPrd | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.9 | Integer32 | read-write | |
| TRA wsCcRfRadioDefaultBasicRates | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.10 | TransmitRate | read-write | |
| TRA wsCcRfRadioDefaultSupportedRates | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.11 | TransmitRate | read-write | |
| T/F wsCcRfRadioDefaultRapDetector | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.12 | TruthValue | read-write | |
| U32 wsCcRfRadioDefaultClusterIndex | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.13 | Unsigned32 | read-write | |
| U32 wsCcRfRadioDefaultMaxMu | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.14 | Unsigned32 | read-write | |
| INT wsCcRfRadioDefaultSelfHealingAction | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.15 | INTEGER | read-write | |
| U32 wsCcRfRadioDefaultSelfHealingPwrOffset | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.16 | Unsigned32 | read-write | |
| T/F wsCcRfRadioDefaultRapSingleChannelScan | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.17 | TruthValue | read-write | Enable or disable single-channel scan for Rogue AP. |
| OCT wsCcRfRadioDefaultBssDtim | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.18 | OCTET STRING | read-write | Set DTIM per BSS. DTIM period is not configurable on a per BSS basis for AP71X1 11n radios. These radios use a single DTIM period across all BSS in a radio which can be configured in wsCcRfRadioDefaultDtimPrd. |
| T/F wsCcRfRadioDefaultMuLocationingEnable | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.19 | TruthValue | read-write | Enable/Disable MU locationing on this radio |
| T/F wsCcRfRadioDefaultRogueApLocationingEnable | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.20 | TruthValue | read-write | Enable/Disable Rogue AP locationing on this radio |
| RAD wsCcRfRadioDefaultAntGain | 1.3.6.1.4.1.388.14.3.2.1.11.8.1.24 | RadioAntennaGain | read-write | Antenna gain. Please see the definition of RadioAntennaGain for additional information. |
| wsCcRfRadioDefaultChannelPowerTable | 1.3.6.1.4.1.388.14.3.2.1.11.9 | not-accessible | Use wsCcRfRadioDefaultChannelPower table to view and set the channel/power/placement properties of the default radio configurations. Please refer to the descriptions in wsCcRfRadioChannelPowerTable | |
| wsCcRfRadioDefaultChannelPowerEntry | 1.3.6.1.4.1.388.14.3.2.1.11.9.1 | not-accessible | ||
| INT wsCcRfRadioDefaultCpPlacement | 1.3.6.1.4.1.388.14.3.2.1.11.9.1.1 | INTEGER | read-write | |
| INT wsCcRfRadioDefaultCpChannelMode | 1.3.6.1.4.1.388.14.3.2.1.11.9.1.2 | INTEGER | read-write | |
| NUM wsCcRfRadioDefaultCpPosChannel | 1.3.6.1.4.1.388.14.3.2.1.11.9.1.3 | MultiPointer64 | read-only | |
| U32 wsCcRfRadioDefaultCpDesChannel | 1.3.6.1.4.1.388.14.3.2.1.11.9.1.4 | Unsigned32 | read-write | |
| I32 wsCcRfRadioDefaultCpPosPowerDb | 1.3.6.1.4.1.388.14.3.2.1.11.9.1.5 | Integer32 | read-only | |
| I32 wsCcRfRadioDefaultCpDesPowerDb | 1.3.6.1.4.1.388.14.3.2.1.11.9.1.6 | Integer32 | read-write | |
| I32 wsCcRfRadioDefaultCpDesPowerMw | 1.3.6.1.4.1.388.14.3.2.1.11.9.1.7 | Integer32 | read-only | |
| DOA wsCcRfRadioDefaultCpSet | 1.3.6.1.4.1.388.14.3.2.1.11.9.1.8 | DoActionShowProgress | read-write | . |
| DOA wsCcRfRadioDefaultCpReset | 1.3.6.1.4.1.388.14.3.2.1.11.9.1.9 | DoActionShowProgress | read-write | |
| wsCcRfRadioDefaultWmmTable | 1.3.6.1.4.1.388.14.3.2.1.11.10 | not-accessible | Configuration parameters for 802.11e / Wireless MultiMedia, which control the Quality of Service between the wireless devices on the network | |
| wsCcRfRadioDefaultWmmEntry | 1.3.6.1.4.1.388.14.3.2.1.11.10.1 | not-accessible | ||
| INT wsCcRfRadioDefaultWmmAccessCategory | 1.3.6.1.4.1.388.14.3.2.1.11.10.1.1 | INTEGER | accessible-for-notify | A label for a particular QoS category of traffic in an 802.11e network. WMM defines 4 Access Categories (Voice, Video, Best Effort, Background). |
| T/F wsCcRfRadioDefaultWmmAdmissionCtrl | 1.3.6.1.4.1.388.14.3.2.1.11.10.1.2 | TruthValue | read-write | |
| U32 wsCcRfRadioDefaultWmmAifsn | 1.3.6.1.4.1.388.14.3.2.1.11.10.1.3 | Unsigned32 | read-write | The Arbitration Inter-Frame Spacing is the wait time in milliSeconds between data frames. A smaller number leads to greater priority for medium access. |
| U32 wsCcRfRadioDefaultWmmTxOp | 1.3.6.1.4.1.388.14.3.2.1.11.10.1.4 | Unsigned32 | read-write | An interval of time where an 802.11e station (MU/AP) has the right to initiate transmissions on the wireless medium. |
| U32 wsCcRfRadioDefaultWmmCwMin | 1.3.6.1.4.1.388.14.3.2.1.11.10.1.5 | Unsigned32 | read-write | If the medium is busy, or a transmitted frame collides, the AP or MU choose a random number between 0 and this minimum contention window size, to decide how long to wait before attempting (re)-transmission. For ease of use this value is configured as a number between 0 and 10; the actual window is calculated using 2**x -1 where x is the value configured. |
| I32 wsCcRfRadioDefaultWmmCwMax | 1.3.6.1.4.1.388.14.3.2.1.11.10.1.6 | Integer32 | read-write | On each collision the AP or MU doubles its initial contention window wait time, until that number is as large as this maximum contention window size. For ease of use this value is configured as a number between 0 and 10; the actual window is calculated using 2**x -1 where x is the value configured. |
| wsCcRfRadioStatusTable | 1.3.6.1.4.1.388.14.3.2.1.11.11 | not-accessible | Status of adopted radios. | |
| wsCcRfRadioStatusEntry | 1.3.6.1.4.1.388.14.3.2.1.11.11.1 | not-accessible | ||
| PHY wsCcRfRadioStatusRadioMac | 1.3.6.1.4.1.388.14.3.2.1.11.11.1.1 | PhysAddress | read-only | Radio MAC address |
| INT wsCcRfRadioStatusState | 1.3.6.1.4.1.388.14.3.2.1.11.11.1.2 | INTEGER | read-only | This value describes the state of the radio. A healthy radio would power-on, and quickly advance from radioUpAndWaitingForConfig and then on to radioReceivingConfig and then on to radioUpAndAdopted. A radio that is denied adoption due to ACLs would show: radioDeniedAdoptionDueToAcl. A radio that does not 'handshake' with the switch properly would be found in state: radioBroken. |
| NUM wsCcRfRadioStatusPtrToAp | 1.3.6.1.4.1.388.14.3.2.1.11.11.1.3 | SinglePointer | read-only | This value is the index in the ApTable for the entry representing the Access Port that contains this radio. Since each radio has one and only one Access Port as 'parent', this value is a simple integer, not a bit-mask. |
| I32 wsCcRfRadioStatusMaxWlans | 1.3.6.1.4.1.388.14.3.2.1.11.11.1.4 | Integer32 | read-only | the maximum number of 802.11 ESSIDs (wireless lans) supported by this radio |
| I32 wsCcRfRadioStatusMaxBss | 1.3.6.1.4.1.388.14.3.2.1.11.11.1.5 | Integer32 | read-only | The maximum number of 802.11 BSSIDs supported by this radio |
| U32 wsCcRfRadioStatusCurrChannel | 1.3.6.1.4.1.388.14.3.2.1.11.11.1.6 | Unsigned32 | read-only | current channel (may be different from configured channel due to DFS etc). |
| I32 wsCcRfRadioStatusCurrPowerDb | 1.3.6.1.4.1.388.14.3.2.1.11.11.1.7 | Integer32 | read-only | Output power level for the radio in Db. |
| I32 wsCcRfRadioStatusCurrPowerMw | 1.3.6.1.4.1.388.14.3.2.1.11.11.1.8 | Integer32 | read-only | Output power level for the radio in Mw. |
| I32 wsCcRfRadioStatusAssociatedMus | 1.3.6.1.4.1.388.14.3.2.1.11.11.1.9 | Integer32 | read-only | Number of associated MUs. |
| TIK wsCcRfRadioStatusLastAdoption | 1.3.6.1.4.1.388.14.3.2.1.11.11.1.10 | TimeTicks | read-only | Timeticks since radio adoption time |
| I32 wsCcRfRadioStatusShortSlotTime | 1.3.6.1.4.1.388.14.3.2.1.11.11.1.11 | Integer32 | read-only | Indicates the 802.11g short-slot time on the radio |
| U32 wsCcRfRadioStatusVlanTag | 1.3.6.1.4.1.388.14.3.2.1.11.11.1.12 | Unsigned32 | read-only | The VLAN tag using which the switch is communicating with the radio |
| INT wsCcRfRadioStatusCfgMethod | 1.3.6.1.4.1.388.14.3.2.1.11.11.1.13 | INTEGER | read-only | The radio can be configured by user before being adopted or by the switch while adoption. |
| U32 wsCcRfRadioStatusAssociatedVoiceMus | 1.3.6.1.4.1.388.14.3.2.1.11.11.1.14 | Unsigned32 | read-only | Number of MUs identified as voice associated. |
| wsCcRf802dt1xRadioAuth | 1.3.6.1.4.1.388.14.3.2.1.11.12 | |||
| STR wsCcRf802dt1xRadioAuthLogin | 1.3.6.1.4.1.388.14.3.2.1.11.12.1 | DisplayString | read-write | 802.1x Port Authentication username. |
| PAS wsCcRf802dt1xRadioAuthPass | 1.3.6.1.4.1.388.14.3.2.1.11.12.2 | Password | read-write | 802.1x Port Authentication password. |
| DOA wsCcRf802dt1xRadioAuthSetRadio | 1.3.6.1.4.1.388.14.3.2.1.11.12.3 | DoActionNow | read-write | Set the username and password stored in wsCcRf802dt1xRadioAuthLogin and wsCcRf802dt1xRadioAuthPass on all radios adopted by the switch. |
| I32 wsCcRfRadioHealingModeCnt | 1.3.6.1.4.1.388.14.3.2.1.11.13 | Integer32 | read-only | Description. |
| I32 wsCcRfRadioNormalModeCnt | 1.3.6.1.4.1.388.14.3.2.1.11.14 | Integer32 | read-write | Description. |
| U32 wsCcRfRadioConfiguredCnt | 1.3.6.1.4.1.388.14.3.2.1.11.15 | Unsigned32 | read-only | Number of configured radios. This is a count of the number of rows in wsCcRfRadioTable. |
| wsCcRfRadioBridgeTable | 1.3.6.1.4.1.388.14.3.2.1.11.16 | not-accessible | This table gives information related to the bridging capabilities of the radios adopted by the wireless switch. | |
| wsCcRfRadioBridgeEntry | 1.3.6.1.4.1.388.14.3.2.1.11.16.1 | not-accessible | An entry in the wsCcRfRadioBridgeTable. | |
| T/F wsCcRfRadioBridgeClientBridgeEnable | 1.3.6.1.4.1.388.14.3.2.1.11.16.1.1 | TruthValue | read-write | Enables or disables client-bridge functionality on the radio. |
| T/F wsCcRfRadioBridgeBaseBridgeEnable | 1.3.6.1.4.1.388.14.3.2.1.11.16.1.2 | TruthValue | read-write | Allows the given radio to act as a base bridge and accept connections from client bridges. |
| STR wsCcRfRadioBridgeSsid | 1.3.6.1.4.1.388.14.3.2.1.11.16.1.3 | DisplayString | read-write | Set the bridge SSID (max length 32 characters). |
| INT wsCcRfRadioBridgeLinkTimeout | 1.3.6.1.4.1.388.14.3.2.1.11.16.1.4 | INTEGER | read-write | Set the bridge link timeout in seconds. |
| INT wsCcRfRadioBridgeMaxClientBridges | 1.3.6.1.4.1.388.14.3.2.1.11.16.1.5 | INTEGER | read-write | Set the maximum client-bridge connections permissible. |
| wsCcRfRadioGroupTable | 1.3.6.1.4.1.388.14.3.2.1.11.20 | not-accessible | A read only table showing radios to their group id mapping. | |
| wsCcRfRadioGroupEntry | 1.3.6.1.4.1.388.14.3.2.1.11.20.1 | not-accessible | An entry in wsCcRfRadioGroupTable. | |
| INT wsCcRfRadioGroupTableGrpId | 1.3.6.1.4.1.388.14.3.2.1.11.20.1.1 | INTEGER | read-only | The group id to which this radio belongs. |
| INT wsCcRfRadioGroupRadioId | 1.3.6.1.4.1.388.14.3.2.1.11.20.1.2 | INTEGER | read-only | The radio id (value same as wsCcRfRadioIndex) which belongs to this group. |
| wsCcRfRadioAdmissionControlTable | 1.3.6.1.4.1.388.14.3.2.1.11.21 | not-accessible | Configure admission control parameters for devices sending voice traffic. | |
| wsCcRfRadioAdmissionControlEntry | 1.3.6.1.4.1.388.14.3.2.1.11.21.1 | not-accessible | Description. | |
| INT wsCcRfRadioAdmissionControlAccessCategory | 1.3.6.1.4.1.388.14.3.2.1.11.21.1.1 | INTEGER | accessible-for-notify | A label for a particular QoS category of traffic. WMM standard suggests to perform admission control for maintaining QoS of traffic sent using Video and Voice access category. |
| U32 wsCcRfRadioAdmissionControlMaxAirTime | 1.3.6.1.4.1.388.14.3.2.1.11.21.1.2 | Unsigned32 | read-write | Maximum percentage of air time that can be distributed among devices sending traffic using a particular access category. For example, configuring a value of 70% for voice, means that a total 700 ms out of 1000 ms will be distributed among devices which setup voice calls. This helps in maintaining the QoS of existing calls on a particular radio. |
| U32 wsCcRfRadioAdmissionControlReservedRoamTime | 1.3.6.1.4.1.388.14.3.2.1.11.21.1.3 | Unsigned32 | read-write | Maxmimum percentage of air time reserved for devices which have roamed. This value should be less than the value specified for wsCcRfRadioAdmissionControlMaxAirTime. |
| U32 wsCcRfRadioAdmissionControlMaxAdmittedDevices | 1.3.6.1.4.1.388.14.3.2.1.11.21.1.4 | Unsigned32 | read-write | Max devices that the radio will admit for sending voice traffic without leading to oversubscription. A value of 0 would disable admission control for the access category. |
| U32 wsCcRfRadioAdmissionControlMaxRoamedDevices | 1.3.6.1.4.1.388.14.3.2.1.11.21.1.5 | Unsigned32 | read-write | Maximum roamed devices that the radio will admit for sending voice traffic after the count of admitted devices has reached wsCcRfRadioAdmissionControlMaxAdmittedDevices. |
| wsCcRfRadioDefaultAdmissionControlTable | 1.3.6.1.4.1.388.14.3.2.1.11.22 | not-accessible | Configure default admission control parameters for different radios. | |
| wsCcRfRadioDefaultAdmissionControlEntry | 1.3.6.1.4.1.388.14.3.2.1.11.22.1 | not-accessible | Description. | |
| INT wsCcRfRadioDefaultAdmissionControlAccessCategory | 1.3.6.1.4.1.388.14.3.2.1.11.22.1.1 | INTEGER | accessible-for-notify | A label for a particular QoS category of traffic. WMM standard suggests to perform admission control for maintaining QoS of traffic sent using Video and Voice access category. |
| U32 wsCcRfRadioDefaultAdmissionControlMaxAirTime | 1.3.6.1.4.1.388.14.3.2.1.11.22.1.2 | Unsigned32 | read-write | The default maximum percentage of air time for a particular access category. |
| U32 wsCcRfRadioDefaultAdmissionControlReservedRoamTime | 1.3.6.1.4.1.388.14.3.2.1.11.22.1.3 | Unsigned32 | read-write | The default percentage of air time reserved for roaming for a particular access category. |
| U32 wsCcRfRadioDefaultAdmissionControlMaxAdmittedDevices | 1.3.6.1.4.1.388.14.3.2.1.11.22.1.4 | Unsigned32 | read-write | The default maximum number of devices that can be admitted to send traffic using a particular access category. |
| U32 wsCcRfRadioDefaultAdmissionControlMaxRoamedDevices | 1.3.6.1.4.1.388.14.3.2.1.11.22.1.5 | Unsigned32 | read-write | The default maximum roamed devices that a radio will admit for sending voice traffic after the count of admitted devices has reached wsCcRfRadioDefaultAdmissionControlMaxAdmittedDevices. |
| wsCcRfRadioAdmissionControlStatusTable | 1.3.6.1.4.1.388.14.3.2.1.11.23 | not-accessible | Description. | |
| wsCcRfRadioAdmissionControlStatusEntry | 1.3.6.1.4.1.388.14.3.2.1.11.23.1 | not-accessible | Description. | |
| INT wsCcRfRadioAdmissionControlStatusAccessCategory | 1.3.6.1.4.1.388.14.3.2.1.11.23.1.1 | INTEGER | accessible-for-notify | Admission control statistics for WMM voice access category. |
| U32 wsCcRfRadioAdmissionControlStatusAirTimeUsage | 1.3.6.1.4.1.388.14.3.2.1.11.23.1.2 | Unsigned32 | read-only | The total percentage of air time used on the radio by devices which have been admitted. |
| U32 wsCcRfRadioAdmissionControlStatusAdmittedDevices | 1.3.6.1.4.1.388.14.3.2.1.11.23.1.3 | Unsigned32 | read-only | Total count of admitted devices. |
| U32 wsCcRfRadioAdmissionControlStatusRoamedDevices | 1.3.6.1.4.1.388.14.3.2.1.11.23.1.4 | Unsigned32 | read-only | Total count of roamed devices which have been admitted. |
| U32 wsCcRfRadioAdmissionControlStatusRequestDenied | 1.3.6.1.4.1.388.14.3.2.1.11.23.1.5 | Unsigned32 | read-only | Total count of requests which have been denied either due to insufficient air time or maximum device capacity. |
| INT wsCcRfRadioAdmissionControlEnable | 1.3.6.1.4.1.388.14.3.2.1.11.24 | INTEGER | read-write | Enable admission control for voice traffic. This also enables WMM admission control for Voice access category. A value of 0 disables admission control across all radios. |
| wsCcRfRadioWipsTable | 1.3.6.1.4.1.388.14.3.2.1.11.25 | not-accessible | This table gives information related to the WIPS mode of the radios adopted by the wireless switch. | |
| wsCcRfRadioWipsEntry | 1.3.6.1.4.1.388.14.3.2.1.11.25.1 | not-accessible | An entry in the wsCcRfRadioWipsTable. | |
| T/F wsCcRfRadioRfFunctionWipsEnable | 1.3.6.1.4.1.388.14.3.2.1.11.25.1.1 | TruthValue | read-write | Converts the given radio from the WLAN mode to the WIPS mode. |
| wsCcRfRadio11nTable | 1.3.6.1.4.1.388.14.3.2.1.11.26 | not-accessible | This table lists all 11n radios adopted by this wireless switch. A row in this table is an extension of a row in wsCcRfRadioTable with the relationship being sparse. | |
| wsCcRfRadio11nEntry | 1.3.6.1.4.1.388.14.3.2.1.11.26.1 | not-accessible | An entry in the table. | |
| T/F wsCcRfRadio11nShortGIEnable | 1.3.6.1.4.1.388.14.3.2.1.11.26.1.1 | TruthValue | read-write | Enable/Disable short guard interval. |
| INT wsCcRfRadio11nAmpduMinSpacing | 1.3.6.1.4.1.388.14.3.2.1.11.26.1.2 | INTEGER | read-write | The minimum spacing between the start of adjacent MPDUs within an A-MPDU. |
| INT wsCcRfRadio11nAmpduRxLimit | 1.3.6.1.4.1.388.14.3.2.1.11.26.1.3 | INTEGER | read-write | The maximum length of A-MPDU that the radio can receive. |
| U32 wsCcRfRadio11nAmpduTxLimit | 1.3.6.1.4.1.388.14.3.2.1.11.26.1.4 | Unsigned32 | read-write | The maximum length of A-MPDU that the radio can send. |
| T/F wsCcRfRadio11nAmpduTxEnable | 1.3.6.1.4.1.388.14.3.2.1.11.26.1.5 | TruthValue | read-write | Enable/Disable transmission of A-MPDU. |
| wsCcRfRadioDefault11nTable | 1.3.6.1.4.1.388.14.3.2.1.11.27 | not-accessible | This table lists the default setting for all supported 11n radios for this wireless switch. A row in this table is an extension of a row in wsCcRfRadioDefaultTable with the relationship being sparse. | |
| wsCcRfRadioDefault11nEntry | 1.3.6.1.4.1.388.14.3.2.1.11.27.1 | not-accessible | An entry in the table. | |
| T/F wsCcRfRadioDefault11nShortGIEnable | 1.3.6.1.4.1.388.14.3.2.1.11.27.1.1 | TruthValue | read-write | Enable/Disable short guard interval. |
| INT wsCcRfRadioDefault11nAmpduMinSpacing | 1.3.6.1.4.1.388.14.3.2.1.11.27.1.2 | INTEGER | read-write | The minimum spacing between the start of adjacent MPDUs within an A-MPDU. |
| INT wsCcRfRadioDefault11nAmpduRxLimit | 1.3.6.1.4.1.388.14.3.2.1.11.27.1.3 | INTEGER | read-write | The maximum length of A-MPDU that the radio can receive. |
| U32 wsCcRfRadioDefault11nAmpduTxLimit | 1.3.6.1.4.1.388.14.3.2.1.11.27.1.4 | Unsigned32 | read-write | The maximum length of A-MPDU that the radio can send. |
| T/F wsCcRfRadioDefault11nAmpduTxEnable | 1.3.6.1.4.1.388.14.3.2.1.11.27.1.5 | TruthValue | read-write | Enable/Disable transmission of A-MPDU. |
| wsCcRfRadioChannelPower11nTable | 1.3.6.1.4.1.388.14.3.2.1.11.28 | not-accessible | This table lists the channel/power/placement properties of 11n radio. A row in this table is an extension of a row in wsCcRfRadioChannelPowerTable with the relationship being sparse. | |
| wsCcRfRadioChannelPower11nEntry | 1.3.6.1.4.1.388.14.3.2.1.11.28.1 | not-accessible | An entry in the table. | |
| INT wsCcRfRadioCp11nChannelWidth | 1.3.6.1.4.1.388.14.3.2.1.11.28.1.1 | INTEGER | read-write | The channel width. This object is for 11n radio when wsCcRfRadioCpChannelMode is 'random' or 'acs'. Values of channel width are: 20 MHz - The Legacy mode, single channel is used 40 MHz - Primary and secondary channel chosen The default channel width is 40 MHz. |
| INT wsCcRfRadioCp11nSecondaryChannel | 1.3.6.1.4.1.388.14.3.2.1.11.28.1.2 | INTEGER | read-write | The choice for secondary channel. This object is for 11n radio when wsCcRfRadioCpChannelMode is 'fixed'. Values of secondary channel are: none - 20 MHz channel width is used. upper - The upper adjacent channel is used thereby doubling the channel width lower - The lower adjacent channel is used thereby doubling the channel width. The default value is 'none'. |
| wsCcRfRadioDefaultChannelPower11nTable | 1.3.6.1.4.1.388.14.3.2.1.11.29 | not-accessible | This table lists the default channel/power/placement properties of 11n radio. A row in this table is an extension of a row in wsCcRfRadioDefaultChannelPowerTable with the relationship being sparse. | |
| wsCcRfRadioDefaultChannelPower11nEntry | 1.3.6.1.4.1.388.14.3.2.1.11.29.1 | not-accessible | An entry in the table. | |
| INT wsCcRfRadioDefaultCp11nChannelWidth | 1.3.6.1.4.1.388.14.3.2.1.11.29.1.1 | INTEGER | read-write | The default channel width. This object is for 11n radio when wsCcRfRadioDefaultCpChannelMode is 'random' or 'acs'. Values of channel width are: 20 MHz - The Legacy mode, single channel is used 40 MHz - Primary and secondary channel chosen The default channel width is 40 MHz. |
| wsCcRfMus | 1.3.6.1.4.1.388.14.3.2.1.12 | |||
| U32 wsCcRfMuCnt | 1.3.6.1.4.1.388.14.3.2.1.12.1 | Unsigned32 | read-only | Number of rows in the wsCcRfMuTable |
| PHY wsCcRfMuLastMac | 1.3.6.1.4.1.388.14.3.2.1.12.2 | PhysAddress | read-only | This scalar records the MAC address of the most recent mu to be associated/disassociated. |
| wsCcRfMuTable | 1.3.6.1.4.1.388.14.3.2.1.12.3 | not-accessible | This table describes general information about each MU serviced by the switch. | |
| wsCcRfMuEntry | 1.3.6.1.4.1.388.14.3.2.1.12.3.1 | not-accessible | ||
| PHY wsCcRfMuMac | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.1 | PhysAddress | read-only | MAC address of the MU. |
| I32 wsCcRfMuWlanIndex | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.2 | Integer32 | read-only | (Reserved for future implementation). |
| I32 wsCcRfMuRadioIndex | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.3 | Integer32 | read-only | The index of the entry in the wsCcRfRadioTable to which this MU is associated. |
| U32 wsCcRfMuVlanIndex | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.4 | Unsigned32 | read-only | The VLAN that this MU is assigned to. |
| U32 wsCcRfMuKeyIndex | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.5 | Unsigned32 | read-only | The key index using which the MU is sending us frames. Useful when pre-shared keys are used with WEP, as we will know if this MU is |
| IP wsCcRfMuIpAddr | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.6 | IpAddress | read-only | IP address of the MU. |
| PHY wsCcRfMuBSS | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.7 | PhysAddress | read-only | The BSSID that this MU is associated with. |
| AUT wsCcRfMuAuthMethod | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.8 | AuthType | read-only | Authentication method implemented by the MU. |
| ENC wsCcRfMuEncMethod | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.9 | EncType | read-only | Encryption method implemented by the MU. |
| RAD wsCcRfMuRadioType | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.10 | RadioType | read-only | Radio type of the MU. |
| INT wsCcRfMuPowerMode | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.11 | INTEGER | read-only | Power-mode implemented by the MU. A MU's status will constantly switch between PSP and CAM mode when it is in PSP mode. |
| TRA wsCcRfMuSupportedRates | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.12 | TransmitRate | read-only | A bit-mask of rates supported by this MU. |
| INT wsCcRfMuVoice | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.13 | INTEGER | read-only | Whether this MU has registered itself as voice-capable. |
| T/F wsCcRfMuIsDataReady | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.14 | TruthValue | read-only | This value is true if the wireless switch is ready to forward/switch packets to/from this MU, (internally called the 'data ready' state). Otherwise this value is false. |
| T/F wsCcRfMuRogueApEna | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.15 | TruthValue | read-only | If true, this MU supports Rogue AP detection assist algorithm. |
| T/F wsCcRfMuIsWmm | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.16 | TruthValue | read-only | If the MU is using WMM |
| U32 wsCcRfMuRoamCount | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.17 | Unsigned32 | read-only | Number of times the mu has roamed without de-authentication. |
| TIK wsCcRfMuLastHeard | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.18 | TimeTicks | read-only | Timeticks since last heard from MU. |
| DOA wsCcRfMuDisassociateNow | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.19 | DoActionNow | read-write | Setting this value to one initiates the action to disassociate the MU. |
| INT wsCcRfMuTunnelIndex | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.20 | INTEGER | read-only | The tunnel identifier for this MU. |
| INT wsCcRfMuQosInfo | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.21 | INTEGER | read-only | UAPSD parameters for a given MU. Has the following bit values : Bit 0 - UAPSD enabled for Voice AC Bit 1 - UAPSD enabled for Video AC Bit 2 - UAPSD enabled for Best-Effort AC Bit 3 - UAPSD enabled for Background AC Bits 4-5 - UAPSD service period ( 00 - unlimited, 01 - 2 packets, 10 - 4 packets, 11 - 6 packets ). |
| U32 wsCcRfMuLastAssoc | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.22 | Unsigned32 | read-only | Number of seconds elapsed since the last association. |
| U32 wsCcRfMuSessionTimeout | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.23 | Unsigned32 | read-only | Session Timeout |
| U32 wsCcRfMuIdleTimeout | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.24 | Unsigned32 | read-only | Idle Timeout |
| STR wsCcRfMuRoleName | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.25 | DisplayString | read-only | The name of the role that this MU is assigned with |
| STR wsCcRfMuGroup | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.26 | DisplayString | read-only | Radius user group to which the MU belongs to |
| STR wsCcRfMuLocation | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.27 | DisplayString | read-only | MU is connected from which zone. This information will be provided by SOLE engine. |
| DOA wsCcRfMuLockOutNow | 1.3.6.1.4.1.388.14.3.2.1.12.3.1.28 | DoActionNow | read-write | Setting this object to one(1) initiates the action to disassociate the MU and set the MAC filter (i.e. associate the ACL) for this MU in one shot. |
| wsCcRfMuHistoryTable | 1.3.6.1.4.1.388.14.3.2.1.12.4 | not-accessible | Description. | |
| wsCcRfMuHistoryEntry | 1.3.6.1.4.1.388.14.3.2.1.12.4.1 | not-accessible | Description. | |
| INT wsCcRfMuHistoryIndex | 1.3.6.1.4.1.388.14.3.2.1.12.4.1.1 | INTEGER | read-only | Simple Index |
| PHY wsCcRfMuHistoryMac | 1.3.6.1.4.1.388.14.3.2.1.12.4.1.2 | PhysAddress | read-only | MAC address of MU |
| INT wsCcRfMuHistoryRadioIndex | 1.3.6.1.4.1.388.14.3.2.1.12.4.1.3 | INTEGER | read-only | Index of Radio |
| INT wsCcRfMuHistoryWlanIndex | 1.3.6.1.4.1.388.14.3.2.1.12.4.1.4 | INTEGER | read-only | Index of Wlan |
| U32 wsCcRfMuHistoryTimestamp | 1.3.6.1.4.1.388.14.3.2.1.12.4.1.5 | Unsigned32 | read-write | The event happened wsCcRfMuHistoryTimestamp seconds ago |
| INT wsCcRfMuHistoryEvent | 1.3.6.1.4.1.388.14.3.2.1.12.4.1.6 | INTEGER | read-write | Event: Adoption, disassociation or timeout. |
| wsCfRfMuProbeHistoryTable | 1.3.6.1.4.1.388.14.3.2.1.12.5 | not-accessible | Description. | |
| wsCfRfMuProbeHistoryEntry | 1.3.6.1.4.1.388.14.3.2.1.12.5.1 | not-accessible | Description. | |
| PHY wsCfRfMuProbeHistoryMac | 1.3.6.1.4.1.388.14.3.2.1.12.5.1.1 | PhysAddress | read-only | Description. |
| INT wsCfRfMuProbeHistoryIndex | 1.3.6.1.4.1.388.14.3.2.1.12.5.1.2 | INTEGER | read-only | Simple Index |
| U32 wsCfRfMuProbeHistoryTimeticks | 1.3.6.1.4.1.388.14.3.2.1.12.5.1.4 | Unsigned32 | read-only | Date and Time |
| I32 wsCfRfMuProbeHistorySignalStrength | 1.3.6.1.4.1.388.14.3.2.1.12.5.1.5 | Integer32 | read-only | It is not yet decided if this will be reported in db or rssi |
| INT wsCfRfMuProbeHeardRadio | 1.3.6.1.4.1.388.14.3.2.1.12.5.1.6 | INTEGER | read-only | Index of the heard radio. |
| INT wsCcRfMuProbeRequestsAgeHeardOut | 1.3.6.1.4.1.388.14.3.2.1.12.6 | INTEGER | read-write | Range is from 15 secs - 15 minutes |
| INT wsCcRfMuHistoryEnable | 1.3.6.1.4.1.388.14.3.2.1.12.7 | INTEGER | read-write | Enable / disable MU history data collection |
| T/F wsCcRfMuHistoryClear | 1.3.6.1.4.1.388.14.3.2.1.12.8 | TruthValue | read-write | Clears the entries in the MU History table. |
| INT wsCcRfMuProbeHistoryEnable | 1.3.6.1.4.1.388.14.3.2.1.12.9 | INTEGER | read-write | Enable / disable MU probe history data collection |
| T/F wsCcRfMuProbeHistoryClear | 1.3.6.1.4.1.388.14.3.2.1.12.10 | TruthValue | read-write | Clears the entries in the MU Probe History table. |
| wsCcRfMuProbeConfigTable | 1.3.6.1.4.1.388.14.3.2.1.12.11 | not-accessible | Table to configure MUs that have to be tracked for probe history status | |
| wsCcRfMuProbeConfigEntry | 1.3.6.1.4.1.388.14.3.2.1.12.11.1 | not-accessible | Description. | |
| INT wsCcRfMuProbeConfigIndex | 1.3.6.1.4.1.388.14.3.2.1.12.11.1.1 | INTEGER | accessible-for-notify | Simple index |
| PHY wsCcRfMuProbeConfigMac | 1.3.6.1.4.1.388.14.3.2.1.12.11.1.2 | PhysAddress | read-write | MAc address of MU to be tracked |
| INT wsCcRfMuProbeConfigStatus | 1.3.6.1.4.1.388.14.3.2.1.12.11.1.3 | INTEGER | read-write | Set tracking on or off for particular MU |
| wsCcRfMuProbeStatusTable | 1.3.6.1.4.1.388.14.3.2.1.12.12 | not-accessible | Status of MU probe history | |
| wsCcRfMuProbeStatusEntry | 1.3.6.1.4.1.388.14.3.2.1.12.12.1 | not-accessible | Description. | |
| INT wsCcRfMuProbeStatusIndex | 1.3.6.1.4.1.388.14.3.2.1.12.12.1.1 | INTEGER | read-only | Simple Index |
| PHY wsCcRfMuProbeStatusMac | 1.3.6.1.4.1.388.14.3.2.1.12.12.1.2 | PhysAddress | read-only | Mac Address |
| U32 wsCcRfMuProbeStatusTimeticks | 1.3.6.1.4.1.388.14.3.2.1.12.12.1.4 | Unsigned32 | read-only | Date and Time |
| I32 wsCcRfMuProbeStatusSignalStrength | 1.3.6.1.4.1.388.14.3.2.1.12.12.1.5 | Integer32 | read-only | It is not yet decided if this will be reported in db or rssi |
| INT wsCcRfMuProbeStatusHeardRadio | 1.3.6.1.4.1.388.14.3.2.1.12.12.1.6 | INTEGER | read-only | Index of the heard radio. |
| PHY wsCcRfMuHistoryStatusMac | 1.3.6.1.4.1.388.14.3.2.1.12.13 | PhysAddress | read-write | The Mac addres which the user want to view the history status |
| wsCcRfMuHistoryStatusTable | 1.3.6.1.4.1.388.14.3.2.1.12.14 | not-accessible | wsCcRfMuHistoryStatusTable, the procedure to view the table will be: 1.set the Mac address you are interested in wsCcRfMuHistoryStatusMac 2.do a walk of the table, and it will show you the history of that MU | |
| wsCcRfMuHistoryStatusEntry | 1.3.6.1.4.1.388.14.3.2.1.12.14.1 | not-accessible | wsCcRfMuHistoryStatusEntry | |
| INT wsCcRfMuHistoryStatusIndex | 1.3.6.1.4.1.388.14.3.2.1.12.14.1.1 | INTEGER | accessible-for-notify | Simple index of wsCcRfMuHistoryStatusTable |
| INT wsCcRfMuHistoryStatusRadioIndex | 1.3.6.1.4.1.388.14.3.2.1.12.14.1.2 | INTEGER | read-only | Index of Radio |
| INT wsCcRfMuHistoryStatusWlanIndex | 1.3.6.1.4.1.388.14.3.2.1.12.14.1.3 | INTEGER | read-only | Index of Wlan |
| U32 wsCcRfMuHistoryStatusTimestamp | 1.3.6.1.4.1.388.14.3.2.1.12.14.1.4 | Unsigned32 | read-only | The event happened wsCcRfMuHistoryTimestamp seconds ago |
| INT wsCcRfMuHistoryStatusEvent | 1.3.6.1.4.1.388.14.3.2.1.12.14.1.5 | INTEGER | read-only | Event: Adoption, disassociation or timeout |
| wsCcRfMuLocationing | 1.3.6.1.4.1.388.14.3.2.1.12.15 | |||
| wsCcRfMuLocationingPreferredTable | 1.3.6.1.4.1.388.14.3.2.1.12.15.1 | not-accessible | Table having MAC addresses of the preferred MUs. Locationing information for these MUs would be captured/reported. | |
| wsCcRfMuLocationingPreferredEntry | 1.3.6.1.4.1.388.14.3.2.1.12.15.1.1 | not-accessible | An entry for the MU locationing Preferred table | |
| INT wsCcRfMuLocationingPreferredIndex | 1.3.6.1.4.1.388.14.3.2.1.12.15.1.1.1 | INTEGER | read-only | Index of the row |
| PHY wsCcRfMuLocationingPreferredMuMac | 1.3.6.1.4.1.388.14.3.2.1.12.15.1.1.2 | PhysAddress | read-create | MAC address of the MU |
| ABB wsCcRfMuLocationingPreferredRowStatus | 1.3.6.1.4.1.388.14.3.2.1.12.15.1.1.3 | AbbrevRowStatus | read-create | Row Status |
| wsCcRfMuLocationingTable | 1.3.6.1.4.1.388.14.3.2.1.12.15.2 | not-accessible | Table giving locationing information about the various MUs. | |
| wsCcRfMuLocationingEntry | 1.3.6.1.4.1.388.14.3.2.1.12.15.2.1 | not-accessible | An entry in MU Locationing Table | |
| INT wsCcRfMuLocationingIndex | 1.3.6.1.4.1.388.14.3.2.1.12.15.2.1.1 | INTEGER | read-only | Index of the row |
| PHY wsCcRfMuLocationingMuMac | 1.3.6.1.4.1.388.14.3.2.1.12.15.2.1.2 | PhysAddress | read-only | MAC address of the MU |
| PHY wsCcRfMuLocationingRadioMac | 1.3.6.1.4.1.388.14.3.2.1.12.15.2.1.3 | PhysAddress | read-only | The MAC address of the radio that heard the Probe Request from the MU |
| I32 wsCcRfMuLocationingSignalStrength | 1.3.6.1.4.1.388.14.3.2.1.12.15.2.1.4 | Integer32 | read-only | The received Signal Strength in dBm |
| I32 wsCcRfMuLocationingHeardChannel | 1.3.6.1.4.1.388.14.3.2.1.12.15.2.1.5 | Integer32 | read-only | Channel on which the MU Probe Request was heard |
| TIK wsCcRfMuLocationingHeardTime | 1.3.6.1.4.1.388.14.3.2.1.12.15.2.1.6 | TimeTicks | read-only | Time in timeticks (since boot), when the MU Probe Request was heard |
| T/F wsCcRfMuLocationingEnable | 1.3.6.1.4.1.388.14.3.2.1.12.15.3 | TruthValue | read-write | Enable/Disable MU locationing. |
| I32 wsCcRfMuLocationingMaxMus | 1.3.6.1.4.1.388.14.3.2.1.12.15.4 | Integer32 | read-write | Maximum number of MUs for MU locationing table. |
| I32 wsCcRfMuLocationingWindowTime | 1.3.6.1.4.1.388.14.3.2.1.12.15.5 | Integer32 | read-write | Time window in seconds to collect the MU probe requests for a MU-Radio pair |
| I32 wsCcRfMuLocationingNumMu | 1.3.6.1.4.1.388.14.3.2.1.12.15.6 | Integer32 | read-only | Current number of MUs in the table. |
| DOA wsCcRfMuLocationingClear | 1.3.6.1.4.1.388.14.3.2.1.12.15.7 | DoActionNow | read-write | Erase the MU locationing Table. |
| wsCcRfMuRateLimiting | 1.3.6.1.4.1.388.14.3.2.1.12.16 | |||
| INT wsCcRfMuRateLimitingUp | 1.3.6.1.4.1.388.14.3.2.1.12.16.1 | INTEGER | read-write | Rate limit in uplink direction, from wireless client to network. The rate is in the range of kbps. The value 0 means that rate limiting is disabled. |
| INT wsCcRfMuRateLimitingDown | 1.3.6.1.4.1.388.14.3.2.1.12.16.2 | INTEGER | read-write | Rate limit in downlink direction, from network to wireless client. The rate is in the range of kbps. The value 0 means that rate limiting is disabled. |
| INT wsCcRfMuLoadBalancingMethod | 1.3.6.1.4.1.388.14.3.2.1.12.17 | INTEGER | read-write | Configure the MUs to be load balanced by user count or by by radio throughput threshold. |
| wsCcRfWlan | 1.3.6.1.4.1.388.14.3.2.1.14 | |||
| wsCcRfWlanTable | 1.3.6.1.4.1.388.14.3.2.1.14.1 | not-accessible | Table of wireless LANs on the switch. | |
| wsCcRfWlanEntry | 1.3.6.1.4.1.388.14.3.2.1.14.1.1 | not-accessible | ||
| I32 wsCcRfWlanIndex | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.1 | Integer32 | accessible-for-notify | Simple index. |
| STA wsCcRfWlanEnable | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.2 | StaticRowEnable | read-write | Enable/Disable wireless Lan. If this wlan is referenced by wsCcRfRadioBssWlanMap, a set to disabled mode will fail. |
| STR wsCcRfWlanDescr | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.3 | DisplayString | read-write | Description the Wlan. |
| STR wsCcRfWlanEssid | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.4 | DisplayString | read-write | ESSID of the WLAN. |
| U32 wsCcRfWlanVlan | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.5 | Unsigned32 | read-write | The Vlan this Wlan is associated with. If not associated with any Vlan, this value will be 0. This object's functionality has now been replaced with wsCcRfWlanVlanTable, which allows to configure upto 32 VLANs per WLAN. |
| T/F wsCcRfWlanDisallowMuToMu | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.6 | TruthValue | read-write | Set to true to prohibit MU-to-MU communication. |
| T/F wsCcRfWlanSecBeacon | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.7 | TruthValue | read-write | Enable the Secure Beacon checkbox to disallow the Access Port from broadcasting an ESSID in its beacons. This is a safeguard to prevent intruders from tapping into the WLAN. Consider this security measure for a private, corporate network. |
| T/F wsCcRfWlanVoicePrioritization | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.8 | TruthValue | read-write | Enable voice prioritization. |
| T/F wsCcRfWlanAnswerBroadcastEss | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.9 | TruthValue | read-write | Answer broadcast ESS. |
| PHY wsCcRfWlanMulticastAddr1 | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.10 | PhysAddress | read-write | Multicast address 1. |
| PHY wsCcRfWlanMulticastAddr2 | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.11 | PhysAddress | read-write | Multicast address 2. |
| I32 wsCcRfWlanWeight | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.12 | Integer32 | read-write | The weight to be used when QoS for all WLANs is set to weighted-round-robin. Note that the sum of all weights across all WLANs need not total 100. |
| T/F wsCcRfWlanWmmEnable | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.13 | TruthValue | read-write | Enable/Disable WMM on this wireless LAN |
| T/F wsCcRfWlanSvpEnable | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.14 | TruthValue | read-write | Enable/Disable support for Spectralink Voice Prioritization on this wireless LAN |
| AUT wsCcRfWlanAuthentication | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.15 | AuthType | read-write | If auth802dot1xEap, additional EAP settings for this WLAN will be used from the matching entry in the wireless authentication. |
| ENC wsCcRfWlanEncryptionMap | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.16 | EncMap | read-write | ** this needs to be a bitmap of enc types ** If cryptoWep64 or cryptoWep128, additional WEP settings for this WLAN will be used from the matching entry in the ccWlanCryptoWepTable. Likewise, if cryptoWpaTkip, use the settings in the matching entry in the ccWlanCryptoWpaTable. Likewise, if cryptoKeyguardMcm, use the settings in the matching entry in the ccWlanCryptoKeyguardTable. |
| ENC wsCcRfWlanBcastEnc | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.17 | EncType | read-only | The broadcast encryption type in use on a WLAN. In most cases it is same as the unicast encryption type. When multiple encryption types are supported (TKIP+CCMP) it is usually the lowest encryption type. |
| U32 wsCcRfWlanNumRadiosAdopted | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.18 | Unsigned32 | read-only | Number of radios adopted. |
| T/F wsCcRfWlanUseDscp | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.19 | TruthValue | read-write | Use Dscp when tagged. |
| I32 wsCcRfWlanMuIdleTime | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.20 | Integer32 | read-write | The number of seconds for which if the switch does not receive/send any data frames from/to an MU, it disassociates the MU. If an MU roams away from an access point without disassociating, this timeout helps the switch determine that the MU is gone, and clear resources allocated for that MU. |
| T/F wsCcRfWlanMobilityEnable | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.21 | TruthValue | read-write | Description. |
| INT wsCcRfWlanGRETunnelIdx | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.22 | INTEGER | read-write | Description. |
| IP wsCcRfWlanGRETunnelGatewayIp | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.23 | IpAddress | read-write | Description. |
| IP wsCcRfWlanGRETunnelGatewayMask | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.24 | IpAddress | read-write | Description. |
| INT wsCcRfWlanMuToMu | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.25 | INTEGER | read-write | States the mode of operation for MU-to-MU communications in the wireless switch. drop(1): traffic is not relayed to other MUs. allow(2): traffic is relayed to other MUs. The value switchToWired(3) is deprecated. Using switchToWired(3) is identical in behavior to the value allow(2). |
| INT wsCcRfWlanQosPrioritization | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.26 | INTEGER | read-write | Sets the prioritization of the WLAN for QoS purposes. |
| T/F wsCcRfWlanDynamicVlanAssignment | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.27 | TruthValue | read-write | Enables or disables dynamic VLAN assignment for the WLAN. |
| INT wsCcRfWlanAccountingType | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.28 | INTEGER | read-write | Indicates if the accounting type is Radius, Syslog or turned off. |
| IP wsCcRfWlanSyslogServerIp | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.29 | IpAddress | read-write | IP Address of the Syslog server |
| U32 wsCcRfWlanSyslogServerPort | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.30 | Unsigned32 | read-write | Port of the Syslog Server |
| INT wsCcRfWlanNacMode | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.31 | INTEGER | read-write | Set NAC mode to 1. Do NAC validation for all MU's except one in exclude list 2. By pass NAC validation for all MU's but include those that are in include list 3. No NAC operation. Go thru RADIUS server if authentication is set to EAP |
| INT wsCcRfWlanQosWeight | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.32 | INTEGER | read-write | Sets the weight of a WLAN. |
| INT wsCcRfWlanHoldTime | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.33 | INTEGER | read-write | Hold time in seconds. The user credentials would hold for this much time when it leaves or roams away. |
| T/F wsCcRfWlanIndependentModeEnable | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.34 | TruthValue | read-write | If true, it means that the Independent mode for this WLAN is enabled. That allows it to be used by AAPs. A false value means that the WLAN is in 'regular' mode and cannot be used for AAPs. |
| T/F wsCcRfWlanClientBridgeBackhaulEnable | 1.3.6.1.4.1.388.14.3.2.1.14.1.1.35 | TruthValue | read-write | Enable client bridge backhaul. Requires wsCcRfWlanIndependentModeEnable to be True for this flag to be enabled. |
| wsCcRfWlanAuth | 1.3.6.1.4.1.388.14.3.2.1.14.2 | |||
| wsCcRfWlanAuthEapTable | 1.3.6.1.4.1.388.14.3.2.1.14.2.1 | not-accessible | Table of EAP authentication settings for each WLAN. | |
| wsCcRfWlanAuthEapEntry | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1 | not-accessible | ||
| IP wsCcRfWlanAuthEapRadiusServerIp1 | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.1 | IpAddress | read-write | IP address of the 1st RADIUS server. |
| I32 wsCcRfWlanAuthEapRadiusServerPort1 | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.2 | Integer32 | read-write | Port number of the 1st RADIUS server. |
| PAS wsCcRfWlanAuthEapRadiusServerSecret1 | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.3 | Password | read-write | Shared secret of the 1st RADIUS server. |
| IP wsCcRfWlanAuthEapRadiusServerIp2 | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.4 | IpAddress | read-write | IP address of the 2nd RADIUS server. |
| I32 wsCcRfWlanAuthEapRadiusServerPort2 | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.5 | Integer32 | read-write | Port number of the 2nd RADIUS server. |
| PAS wsCcRfWlanAuthEapRadiusServerSecret2 | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.6 | Password | read-write | Shared secret of the 2nd RADIUS server. |
| I32 wsCcRfWlanAuthEapSuppRetries | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.7 | Integer32 | read-write | Supplicant max retries. |
| I32 wsCcRfWlanAuthEapSuppTimeout | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.8 | Integer32 | read-write | Supplicant timeout. |
| I32 wsCcRfWlanAuthEapServerRetries | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.9 | Integer32 | read-write | Server max retries. |
| I32 wsCcRfWlanAuthEapServerTimeout | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.10 | Integer32 | read-write | Server timeout. |
| T/F wsCcRfWlanAuthEapReauth | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.11 | TruthValue | read-write | Enable reauthentication. |
| I32 wsCcRfWlanAuthEapReauthTimeout | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.12 | Integer32 | read-write | Reauthentication timeout. |
| INT wsCcRfWlanAuthEapAuthProtocol | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.13 | INTEGER | read-write | The authentication protocol to be used, PAP or CHAP. |
| INT wsCcRfWlanAuthEapDscpTos | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.14 | INTEGER | read-write | DSCP or TOS value to be used (between 0 and 63). |
| INT wsCcRfWlanAuthEapAccountingMode | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.15 | INTEGER | read-write | Indicates if mode of accounting is one of: Start-Stop, Start-only or Start-interim-Stop |
| U32 wsCcRfWlanAuthEapInterimAcctInterval | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.16 | Unsigned32 | read-write | Interval for interim accounting |
| U32 wsCcRfWlanAuthEapAcctTimeout | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.17 | Unsigned32 | read-write | Timeout value for accounting option |
| U32 wsCcRfWlanAuthEapAcctRetries | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.18 | Unsigned32 | read-write | Number of accounting retries |
| IP wsCcRfWlanAuthPrimaryServer | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.19 | IpAddress | read-write | IP Address of the Primary Accounting Server |
| IP wsCcRfWlanAuthEapSecondaryServer | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.20 | IpAddress | read-write | IP Address of the Secondary Accounting Server |
| U32 wsCcRfWlanAuthEapPrimarySrvrPort | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.21 | Unsigned32 | read-write | Port Number of the Primary Server |
| U32 wsCcRfWlanAuthEapSecondarySrvrPort | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.22 | Unsigned32 | read-write | Port Number of the Secondary Server |
| STR wsCcRfWlanAuthEapPrimarySecret | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.23 | DisplayString | read-write | Shared secret of the Primary Accounting server. |
| STR wsCcRfWlanAuthEapSecondarySecret | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.24 | DisplayString | read-write | Shared secret of the Secondary Accounting server. |
| INT wsCcRfWlanAuthEapRadiusMacAuthFormat | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.25 | INTEGER | read-write | The format of the MAC address to be sent to a RADIUS server when using MAC authentication: no-delim: No Delimiter - AABBCCDDEEFF pair-colon: Colon Delmilter per Pair - AA:BB:CC:DD:EE:FF pair-dash: Dash Delimiter per Pair - AA-BB-CC-DD-EE-FF quad-dot: Dot Delimiter per Four Hex - AABB.CCDD.EEFF middle-dash: Dash Delmiter in the middle - AABBCC-DDEEFF |
| T/F wsCcRfWlanAuthEapAapProxyRadiusEnable | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.26 | TruthValue | read-write | Enable proxying AAP radius requests. |
| T/F wsCcRfWlanAuthEapRadiusDynamicAuthEnable | 1.3.6.1.4.1.388.14.3.2.1.14.2.1.1.27 | TruthValue | read-write | Enable support for Radius Dynamic Authorization extensions such as Disconnect Message, and Change-Of-Authorization, as described in RFC 3576 |
| wsCcRfWlanAuthKerberosTable | 1.3.6.1.4.1.388.14.3.2.1.14.2.2 | not-accessible | Table of Kerberos authentication settings for each WLAN. | |
| wsCcRfWlanAuthKerberosEntry | 1.3.6.1.4.1.388.14.3.2.1.14.2.2.1 | not-accessible | ||
| STR wsCcRfwlanAuthKerbRealm | 1.3.6.1.4.1.388.14.3.2.1.14.2.2.1.1 | DisplayString | read-write | Realm name. A realm name functions similarly to a DNS domain name. In theory, the realm name is arbitrary. However, in practice a Kerberos realm is named by uppercasing the DNS domain name that is associated with hosts in the realm. |
| PAS wsCcRfWlanAuthKerbPassword | 1.3.6.1.4.1.388.14.3.2.1.14.2.2.1.2 | Password | read-write | Password for the Kerberos configuration. |
| IP wsCcRfWlanAuthKerbKdcServerIp1 | 1.3.6.1.4.1.388.14.3.2.1.14.2.2.1.3 | IpAddress | read-write | IP address of the 1st Kerberos server. |
| I32 wsCcRfWlanAuthKerbKdcServerPort1 | 1.3.6.1.4.1.388.14.3.2.1.14.2.2.1.4 | Integer32 | read-write | Port number of the 1st Kerberos server. |
| IP wsCcRfWlanAuthKerbKdcServerIp2 | 1.3.6.1.4.1.388.14.3.2.1.14.2.2.1.5 | IpAddress | read-write | IP address of the 2nd Kerberos server. |
| I32 wsCcRfWlanAuthKerbKdcServerPort2 | 1.3.6.1.4.1.388.14.3.2.1.14.2.2.1.6 | Integer32 | read-write | Port number of the 2nd Kerberos server. |
| I32 wsCcRfWlanAuthKerberosServerTimeout | 1.3.6.1.4.1.388.14.3.2.1.14.2.2.1.7 | Integer32 | read-write | Description. |
| wsCcRfWlanAuthEapNACServerTable | 1.3.6.1.4.1.388.14.3.2.1.14.2.3 | not-accessible | Table of Exclude lists EAP authentication settings for each WLAN. | |
| wsCcRfWlanAuthEapNACServerEntry | 1.3.6.1.4.1.388.14.3.2.1.14.2.3.1 | not-accessible | ||
| IP wsCcRfWlanAuthEapNACServerIp1 | 1.3.6.1.4.1.388.14.3.2.1.14.2.3.1.1 | IpAddress | read-write | IP address of the 1st NAC server. |
| INT wsCcRfWlanAuthEapNACServerPort1 | 1.3.6.1.4.1.388.14.3.2.1.14.2.3.1.2 | INTEGER | read-write | Port number of the 1st NAC server. |
| PAS wsCcRfWlanAuthEapNACServerSecret1 | 1.3.6.1.4.1.388.14.3.2.1.14.2.3.1.3 | Password | read-write | Shared secret of the 1st NAC server. |
| IP wsCcRfWlanAuthEapNACServerIp2 | 1.3.6.1.4.1.388.14.3.2.1.14.2.3.1.4 | IpAddress | read-write | IP address of the 2nd NAC server. |
| INT wsCcRfWlanAuthEapNACServerPort2 | 1.3.6.1.4.1.388.14.3.2.1.14.2.3.1.5 | INTEGER | read-write | Port number of the 2nd NAC server. |
| PAS wsCcRfWlanAuthEapNACServerSecret2 | 1.3.6.1.4.1.388.14.3.2.1.14.2.3.1.6 | Password | read-write | Shared secret of the 2nd NAC server. |
| I32 wsCcRfWlanAuthEapNACServerRetries | 1.3.6.1.4.1.388.14.3.2.1.14.2.3.1.7 | Integer32 | read-write | Server max retries. |
| I32 wsCcRfWlanAuthEapNACServerTimeout | 1.3.6.1.4.1.388.14.3.2.1.14.2.3.1.8 | Integer32 | read-write | Server timeout. |
| wsCcRfWlanEnc | 1.3.6.1.4.1.388.14.3.2.1.14.3 | |||
| T/F wsCcRfWlanEncSkEnable | 1.3.6.1.4.1.388.14.3.2.1.14.3.1 | TruthValue | read-write | Enable/disable Wlan encryption shared-key |
| wsCcRfWlanEncWep64Table | 1.3.6.1.4.1.388.14.3.2.1.14.3.2 | not-accessible | Table of WEP encryption settings for each WLAN. | |
| wsCcRfWlanEncWep64Entry | 1.3.6.1.4.1.388.14.3.2.1.14.3.2.1 | not-accessible | ||
| U32 wsCcRfWlanEncWep64KeyIndex | 1.3.6.1.4.1.388.14.3.2.1.14.3.2.1.1 | Unsigned32 | read-write | Specifies which WEP key to use. |
| OCT wsCcRfWlanEncWep64Key1 | 1.3.6.1.4.1.388.14.3.2.1.14.3.2.1.2 | OCTET STRING | read-write | WEP key #1 exactly 5 octets for WEP-64 (40-bit key). |
| OCT wsCcRfWlanEncWep64Key2 | 1.3.6.1.4.1.388.14.3.2.1.14.3.2.1.3 | OCTET STRING | read-write | WEP key #2 exactly 5 octets for WEP-64 (40-bit key). |
| OCT wsCcRfWlanEncWep64Key3 | 1.3.6.1.4.1.388.14.3.2.1.14.3.2.1.4 | OCTET STRING | read-write | WEP key #3 exactly 5 octets for WEP-64 (40-bit key). |
| OCT wsCcRfWlanEncWep64Key4 | 1.3.6.1.4.1.388.14.3.2.1.14.3.2.1.5 | OCTET STRING | read-write | WEP key #4 exactly 5 octets for WEP-64 (40-bit key). |
| wsCcRfWlanEncWep128KgTable | 1.3.6.1.4.1.388.14.3.2.1.14.3.3 | not-accessible | Table of WEP encryption settings for each WLAN. | |
| wsCcRfWlanEncWep128KgEntry | 1.3.6.1.4.1.388.14.3.2.1.14.3.3.1 | not-accessible | ||
| U32 wsCcRfWlanEncWep128KgKeyIndex | 1.3.6.1.4.1.388.14.3.2.1.14.3.3.1.1 | Unsigned32 | read-write | Specifies which WEP key to use. |
| OCT wsCcRfWlanEncWep128KgKey1 | 1.3.6.1.4.1.388.14.3.2.1.14.3.3.1.2 | OCTET STRING | read-write | WEP key #1 exactly 13 octets for WEP-128 (104-bit key); |
| OCT wsCcRfWlanEncWep128KgKey2 | 1.3.6.1.4.1.388.14.3.2.1.14.3.3.1.3 | OCTET STRING | read-write | WEP key #2 exactly 13 octets for WEP-128 (104-bit key); |
| OCT wsCcRfWlanEncWep128KgKey3 | 1.3.6.1.4.1.388.14.3.2.1.14.3.3.1.4 | OCTET STRING | read-write | WEP key #3 exactly 13 octets for WEP-128 (104-bit key); |
| OCT wsCcRfWlanEncWep128KgKey4 | 1.3.6.1.4.1.388.14.3.2.1.14.3.3.1.5 | OCTET STRING | read-write | WEP key #4 exactly 13 octets for WEP-128 (104-bit key); |
| wsCcRfWlanEncTkipCcmpTable | 1.3.6.1.4.1.388.14.3.2.1.14.3.4 | not-accessible | Table of Tkip/Ccmp encryption settings for each WLAN. | |
| wsCcRfWlanEncTkipCcmpEntry | 1.3.6.1.4.1.388.14.3.2.1.14.3.4.1 | not-accessible | ||
| INT wsCcRfWlanEncTkipCcmpKeyType | 1.3.6.1.4.1.388.14.3.2.1.14.3.4.1.1 | INTEGER | read-write | Specify whether to use key or passphrase. |
| PAS wsCcRfWlanEncTkipCcmpPassphrase | 1.3.6.1.4.1.388.14.3.2.1.14.3.4.1.2 | Password | read-write | Passphrase. |
| OCT wsCcRfWlanEncTkipCcmpKey | 1.3.6.1.4.1.388.14.3.2.1.14.3.4.1.3 | OCTET STRING | read-write | Key. |
| T/F wsCcRfWlanEncTkipCcmpKeyRotation | 1.3.6.1.4.1.388.14.3.2.1.14.3.4.1.4 | TruthValue | read-write | A truth-value that indicates whether the group key for a TKIP/CCMP mobile-unit should be periodically rotated. |
| I32 wsCcRfWlanEncTkipCcmpKeyInterval | 1.3.6.1.4.1.388.14.3.2.1.14.3.4.1.5 | Integer32 | read-write | The number of seconds after which the broadcast key of all mobile-units on a particular wireless lan is replaced by a new broadcast key. |
| T/F wsCcRfWlanEncTkipCcmpPmkCaching | 1.3.6.1.4.1.388.14.3.2.1.14.3.4.1.6 | TruthValue | read-write | Whether IEEE 802.11i PMK caching is enabled. Use of PMK caching allows a mobile-unit to authenticate just once to an AP, even if it roams away from it, and roams back to it. Enabling this feature results in much faster roam times on wireless LANs that use 802.1x authentication. |
| T/F wsCcRfWlanEncTkipCcmpOppPmkCaching | 1.3.6.1.4.1.388.14.3.2.1.14.3.4.1.7 | TruthValue | read-write | Whether extensions to IEEE 802.11i PMK caching, known as opportunistic PMK caching, are enabled. It extends PMK caching (authenticate once to an AP) to the whole switch (authenticate once to a switch). Enabling this feature results in much faster roam times on wireless LANs that use 802.1x authentication |
| T/F wsCcRfWlanEncTkipCcmpPreauthentication | 1.3.6.1.4.1.388.14.3.2.1.14.3.4.1.8 | TruthValue | read-write | Whether pre-authentication is enabled. |
| wsCcRfWlanEncPhraseToWep | 1.3.6.1.4.1.388.14.3.2.1.14.3.5 | |||
| STR wsCcRfWlanEncP2WPassphrase | 1.3.6.1.4.1.388.14.3.2.1.14.3.5.1 | DisplayString | read-write | An input to an algorithm used to convert ascii into wep keys. |
| OCT wsCcRfWlanEncP2WKey1 | 1.3.6.1.4.1.388.14.3.2.1.14.3.5.2 | OCTET STRING | read-only | Generated Wep128 key #1. |
| OCT wsCcRfWlanEncP2WKey2 | 1.3.6.1.4.1.388.14.3.2.1.14.3.5.3 | OCTET STRING | read-only | Generated Wep128 key #2. |
| OCT wsCcRfWlanEncP2WKey3 | 1.3.6.1.4.1.388.14.3.2.1.14.3.5.4 | OCTET STRING | read-only | Generated Wep128 key #3. |
| OCT wsCcRfWlanEncP2WKey4 | 1.3.6.1.4.1.388.14.3.2.1.14.3.5.5 | OCTET STRING | read-only | Generated Wep128 key #4. |
| DOA wsCcRfWlanEncP2WClearKeys | 1.3.6.1.4.1.388.14.3.2.1.14.3.5.6 | DoActionNow | read-write | Setting this scalar to 1 will clear all wep key fields. |
| wsCcRfWlanWmmTable | 1.3.6.1.4.1.388.14.3.2.1.14.4 | not-accessible | Configuration parameters for 802.11e / Wireless MultiMedia, which control the Quality of Service between the wireless devices on the network | |
| wsCcRfWlanWmmEntry | 1.3.6.1.4.1.388.14.3.2.1.14.4.1 | not-accessible | ||
| WLA wsCcRfWlanWmmBeParm | 1.3.6.1.4.1.388.14.3.2.1.14.4.1.1 | WlanWmmConfig | read-write | Parameters for the Best Effort QoS category of traffic in an 802.11e network. Prior to setting this field, please be sure to get the current value. |
| WLA wsCcRfWlanWmmBkParm | 1.3.6.1.4.1.388.14.3.2.1.14.4.1.2 | WlanWmmConfig | read-write | Parameters for the Background QoS category of traffic in an 802.11e network. Prior to setting this field, please be sure to get the current value. |
| WLA wsCcRfWlanWmmViParm | 1.3.6.1.4.1.388.14.3.2.1.14.4.1.3 | WlanWmmConfig | read-write | Parameters for the Video QoS category of traffic in an 802.11e network. Prior to setting this field, please be sure to get the current value. |
| WLA wsCcRfWlanWmmVoParm | 1.3.6.1.4.1.388.14.3.2.1.14.4.1.4 | WlanWmmConfig | read-write | Parameters for the Voice QoS category of traffic in an 802.11e network. Prior to setting this field, please be sure to get the current value. |
| INT wsCcRfWlanCount | 1.3.6.1.4.1.388.14.3.2.1.14.5 | INTEGER | read-only | the current number of wlan in the system |
| wsCcRfWlanClientIncludeListTable | 1.3.6.1.4.1.388.14.3.2.1.14.6 | not-accessible | Configuration for Include lists and hosts. The host entries existing in this list will go through NAC check if this client include list name is added into WLAN. | |
| wsCcRfWlanClientIncludeListEntry | 1.3.6.1.4.1.388.14.3.2.1.14.6.1 | not-accessible | Include list and host entry contains information about host mac address and mac mask to include for NAC status check. | |
| STR wsCcRfWlanClientIncludeListName | 1.3.6.1.4.1.388.14.3.2.1.14.6.1.1 | DisplayString | read-only | Indexed by Include List Names. |
| STR wsCcRfWlanClientIncludeListHostName | 1.3.6.1.4.1.388.14.3.2.1.14.6.1.2 | DisplayString | read-only | String index of Mu host names for the WlanClientIncludeListTable. |
| PHY wsCcRfWlanClientIncludeListMAC | 1.3.6.1.4.1.388.14.3.2.1.14.6.1.3 | PhysAddress | read-create | Host MAC address. This is a MAC address of the Mobile Units. Example: 00:0A:12:34:BE:OF |
| PHY wsCcRfWlanClientIncludeListMACMask | 1.3.6.1.4.1.388.14.3.2.1.14.6.1.4 | PhysAddress | read-create | Host end MAC address. This field is used to specify the range of MAC addresses. Example: 00:0A:12:34:BE:FF |
| ABB wsCcRfWlanClientIncludeListRowStatus | 1.3.6.1.4.1.388.14.3.2.1.14.6.1.5 | AbbrevRowStatus | read-create | Create or Delete a row from Include list Table. |
| wsCcRfWlanClientExcludeListTable | 1.3.6.1.4.1.388.14.3.2.1.14.7 | not-accessible | Configuration for Exclude lists and hosts. The host entries existing in this list will not go through NAC check if its associated to the particular WLAN. | |
| wsCcRfWlanClientExcludeListEntry | 1.3.6.1.4.1.388.14.3.2.1.14.7.1 | not-accessible | Exclude list and host entry contains information about host mac address and mac mask to exclude from NAC operation. | |
| STR wsCcRfWlanClientExcludeListName | 1.3.6.1.4.1.388.14.3.2.1.14.7.1.1 | DisplayString | read-only | Indexed by Exclude List Names. |
| STR wsCcRfWlanClientExcludeListHostName | 1.3.6.1.4.1.388.14.3.2.1.14.7.1.2 | DisplayString | read-only | String index of Mu host names for the WlanClientExcludeListTable. |
| PHY wsCcRfWlanClientExcludeListMAC | 1.3.6.1.4.1.388.14.3.2.1.14.7.1.3 | PhysAddress | read-create | Host MAC address. This is a MAC address of the Mobile Units. Example: 00:0A:12:34:BE:OF |
| PHY wsCcRfWlanClientExcludeListMACMask | 1.3.6.1.4.1.388.14.3.2.1.14.7.1.4 | PhysAddress | read-create | Host end MAC address. This field is used to specify the range of MAC addresses. Example: 00:0A:12:34:BE:FF |
| ABB wsCcRfWlanClientExcludeListRowStatus | 1.3.6.1.4.1.388.14.3.2.1.14.7.1.5 | AbbrevRowStatus | read-create | Create or Delete a row from Exclude list Table. |
| wsCcRfWlanClientListWlanMapTable | 1.3.6.1.4.1.388.14.3.2.1.14.8 | not-accessible | Configure wlan mapping for this client list. The list could be include or exclude list name. | |
| wsCcRfWlanClientListWlanMapEntry | 1.3.6.1.4.1.388.14.3.2.1.14.8.1 | not-accessible | This table will allow the user to associate client exclude and include lists to each WLAN. | |
| STR wsCcRfWlanClientListName | 1.3.6.1.4.1.388.14.3.2.1.14.8.1.1 | DisplayString | read-only | Client exclude and include list name(s). This is a read only index which will display all the exclude and include list names created before (in wsCcRfWlanClientIncludeListTable and wsCcRfWlanClientExcludeListTable). |
| NUM wsCcRfWlanClientListWlanBitmap | 1.3.6.1.4.1.388.14.3.2.1.14.8.1.2 | MultiPointer256 | read-write | Adding client list (include and exclude list) to wlan(s). This is bitmap value (which is from 1 to maximum wlans ie., 1-256). |
| wsCcRfWlanVlanTable | 1.3.6.1.4.1.388.14.3.2.1.14.9 | not-accessible | Table of Vlans assigned to parent Wlan | |
| wsCcRfWlanVlanEntry | 1.3.6.1.4.1.388.14.3.2.1.14.9.1 | not-accessible | An entry in wsCcRfWlanVlanTable | |
| I32 wsCcRfWlanVlanIndex | 1.3.6.1.4.1.388.14.3.2.1.14.9.1.1 | Integer32 | read-only | The numeric vlan ID for this vlan entry, valid range is [ 1, 4094 ]. |
| INT wsCcRfWlanVlanUserLimit | 1.3.6.1.4.1.388.14.3.2.1.14.9.1.2 | INTEGER | read-create | The maximum number of users that can be associated on this VLAN of the WLAN. The value 0 has a special meaning. It means no limit on this VLAN of the WLAN. Other limits, such as maximum number of users per radio, etc, would still apply. Also, the maximum number of users is limited by the maximum number of MUs supported by the wireless switch e.g. 4096 for WS5100, 8192 for RFS7000. The range given here is the upper limit for any WiOS platform. |
| ABB wsCcRfWlanVlanRowStatus | 1.3.6.1.4.1.388.14.3.2.1.14.9.1.3 | AbbrevRowStatus | read-create | At the time of row-creation, rowStatus is set to createAndGo(4). If user does not wish to have this vlanIndex mapped to a WLAN any more, user deletes the row by setting rowstatus to destroy(6). When a walk is done on this table, it will show one row for each vlan-wlan mapping and the rowStatus of all those rows will be active(1). |
| I32 wsCcRfWlanMaxVlans | 1.3.6.1.4.1.388.14.3.2.1.14.10 | Integer32 | read-only | Maximum number of vlans per wlan. |
| STR wsCcRfWlanVlanLastError | 1.3.6.1.4.1.388.14.3.2.1.14.11 | DisplayString | read-only | The last error message on vlan table operation. It is not cleared. |
| T/F wsCcRfWlanBwAllocationEnable | 1.3.6.1.4.1.388.14.3.2.1.14.13 | TruthValue | read-write | Enables or Disables Wlan Bandwidth Allocation. |
| wsCcRfAssocAcl | 1.3.6.1.4.1.388.14.3.2.1.15 | |||
| wsCcRfMuAssocAclTable | 1.3.6.1.4.1.388.14.3.2.1.15.1 | not-accessible | A table that allows users to filter MUs that are allowed/denied association to different WLANs based on their MAC address | |
| wsCcRfMuAssocAclEntry | 1.3.6.1.4.1.388.14.3.2.1.15.1.1 | not-accessible | ||
| I32 wsCcRfMuAssocAclIndex | 1.3.6.1.4.1.388.14.3.2.1.15.1.1.1 | Integer32 | accessible-for-notify | Simple index. |
| INT wsCcRfMuAssocAclMode | 1.3.6.1.4.1.388.14.3.2.1.15.1.1.2 | INTEGER | read-create | Allow or deny the Mac range specified by wsCcRfWlanMuAclStartingMac and wsCcRfWlanMuAclEndingMac. |
| PHY wsCcRfMuAssocAclStartingMac | 1.3.6.1.4.1.388.14.3.2.1.15.1.1.3 | PhysAddress | read-create | Starting MAC address in a range or addresses. |
| PHY wsCcRfMuAssocAclEndingMac | 1.3.6.1.4.1.388.14.3.2.1.15.1.1.4 | PhysAddress | read-create | Ending MAC address in a range of addresses. |
| NUM wsCcRfMuAssocAclWlans | 1.3.6.1.4.1.388.14.3.2.1.15.1.1.5 | MultiPointer64 | read-create | The list of WLANs that this ACL rule applies to |
| ROW wsCcRfMuAssocAclRowStatus | 1.3.6.1.4.1.388.14.3.2.1.15.1.1.6 | RowStatus | read-create | Row status. |
| wsCcRfRap | 1.3.6.1.4.1.388.14.3.2.1.16 | |||
| INT wsCcRfRapMode | 1.3.6.1.4.1.388.14.3.2.1.16.1 | INTEGER | read-write | Enable/disable rogue AP detection |
| I32 wsCcRfRapMaxRogue | 1.3.6.1.4.1.388.14.3.2.1.16.2 | Integer32 | read-write | The maximum number of rows in wsCcRfRapStatusTable |
| I32 wsCcRfRapTimeout | 1.3.6.1.4.1.388.14.3.2.1.16.3 | Integer32 | read-write | The amount of time a rogue AP will remain after it is no longer seen |
| wsCcRfRapCfgTable | 1.3.6.1.4.1.388.14.3.2.1.16.4 | not-accessible | Configure rogue-ap (ap-detection) parameter | |
| wsCcRfRapCfgEntry | 1.3.6.1.4.1.388.14.3.2.1.16.4.1 | not-accessible | ||
| I32 wsCcRfRapCfgIndex | 1.3.6.1.4.1.388.14.3.2.1.16.4.1.1 | Integer32 | accessible-for-notify | Simple index |
| T/F wsCcRfRapCfgAnyMac | 1.3.6.1.4.1.388.14.3.2.1.16.4.1.2 | TruthValue | read-create | any Mac address |
| PHY wsCcRfRapCfgMac | 1.3.6.1.4.1.388.14.3.2.1.16.4.1.3 | PhysAddress | read-create | Mac address |
| T/F wsCcRfRapCfgAnySsid | 1.3.6.1.4.1.388.14.3.2.1.16.4.1.4 | TruthValue | read-create | Any ssid |
| STR wsCcRfRapCfgSsid | 1.3.6.1.4.1.388.14.3.2.1.16.4.1.5 | DisplayString | read-create | ssid |
| ROW wsCcRfRapCfgRowStatus | 1.3.6.1.4.1.388.14.3.2.1.16.4.1.6 | RowStatus | read-create | Row status |
| wsCcRfRapStatusTable | 1.3.6.1.4.1.388.14.3.2.1.16.5 | not-accessible | Status of AP assisted approved and un-approved access ports | |
| wsCcRfRapStatusEntry | 1.3.6.1.4.1.388.14.3.2.1.16.5.1 | not-accessible | ||
| INT wsCcRfRapStatusType | 1.3.6.1.4.1.388.14.3.2.1.16.5.1.1 | INTEGER | read-only | Radio type. |
| PHY wsCcRfRapStatusMac | 1.3.6.1.4.1.388.14.3.2.1.16.5.1.2 | PhysAddress | read-only | Mac address of the access port |
| U32 wsCcRfRapStatusHeardAp | 1.3.6.1.4.1.388.14.3.2.1.16.5.1.3 | Unsigned32 | read-only | Index of the heard access port |
| I32 wsCcRfRapStatusChannel | 1.3.6.1.4.1.388.14.3.2.1.16.5.1.4 | Integer32 | read-only | Channel of heard radio |
| STR wsCcRfRapStatusSsid | 1.3.6.1.4.1.388.14.3.2.1.16.5.1.5 | DisplayString | read-only | Ssid of heard radio |
| TIK wsCcRfRapStatusLastTimeSeen | 1.3.6.1.4.1.388.14.3.2.1.16.5.1.6 | TimeTicks | read-only | The number of second(s) ago this ap was last seen. |
| I32 wsCcRfRapStatusLastSignal | 1.3.6.1.4.1.388.14.3.2.1.16.5.1.7 | Integer32 | read-only | Last signal level from the radio. |
| I32 wsCcRfRapStatusMinSignal | 1.3.6.1.4.1.388.14.3.2.1.16.5.1.8 | Integer32 | read-only | Weakest signal heard from this radio. |
| I32 wsCcRfRapStatusMaxSignal | 1.3.6.1.4.1.388.14.3.2.1.16.5.1.9 | Integer32 | read-only | Strongest signal heard from this radio. |
| I32 wsCcRfRapStatusSumSignal | 1.3.6.1.4.1.388.14.3.2.1.16.5.1.10 | Integer32 | read-only | Sum of all signal values for this radio. |
| C32 wsCcRfRapStatusSignalCountEx | 1.3.6.1.4.1.388.14.3.2.1.16.5.1.11 | Counter32 | read-only | Number of signal data points for this radio. |
| INT wsCcRfRapMuAssistMode | 1.3.6.1.4.1.388.14.3.2.1.16.6 | INTEGER | read-write | Enable mobile-unit assisted scanning |
| INT wsCcRfRapMuAssistRefreshPeriod | 1.3.6.1.4.1.388.14.3.2.1.16.7 | INTEGER | read-write | The period in seconds with which all scan-capable mobile-units are requested to scan for neighboring APs |
| INT wsCcRfRUnpprovedApTimeout | 1.3.6.1.4.1.388.14.3.2.1.16.8 | INTEGER | read-write | The amount of time an unapproved AP will remain after it is no longer seen |
| INT wsCcRfRApprovedApTimeout | 1.3.6.1.4.1.388.14.3.2.1.16.9 | INTEGER | read-write | The amount of time an approved AP will remain after it is no longer seen |
| wsCcRfRapMuAssistTable | 1.3.6.1.4.1.388.14.3.2.1.16.10 | not-accessible | Status of MU assisted un-approved access ports | |
| wsCcRfRapMuAssistEntry | 1.3.6.1.4.1.388.14.3.2.1.16.10.1 | not-accessible | Description. | |
| INT wsCcRfRapMuAssistIndex | 1.3.6.1.4.1.388.14.3.2.1.16.10.1.1 | INTEGER | read-only | Simple index of approved and unapproved APs |
| PHY wsCcRfRapMuAssistMac | 1.3.6.1.4.1.388.14.3.2.1.16.10.1.2 | PhysAddress | read-only | MAC address of the access port |
| U32 wsCcRfRapMuAssistFoundOnPrtl | 1.3.6.1.4.1.388.14.3.2.1.16.10.1.3 | Unsigned32 | read-only | Portal with which the MU is associated |
| U32 wsCcRfRapMuAssistTimestamp | 1.3.6.1.4.1.388.14.3.2.1.16.10.1.4 | Unsigned32 | read-only | Timestamp at which the radio was last heard |
| STR wsCcRfRapMuAssistSsid | 1.3.6.1.4.1.388.14.3.2.1.16.10.1.5 | DisplayString | read-only | Ssid of heard radio |
| PHY wsCcRfRapMuAssistBss | 1.3.6.1.4.1.388.14.3.2.1.16.10.1.6 | PhysAddress | read-only | Bss of the heard radio |
| U32 wsCcRfRapMuAssistRssi | 1.3.6.1.4.1.388.14.3.2.1.16.10.1.7 | Unsigned32 | read-only | RSSI of the heard radio |
| wsCcRfRapLocationing | 1.3.6.1.4.1.388.14.3.2.1.16.11 | |||
| wsCcRfRapLocationingTable | 1.3.6.1.4.1.388.14.3.2.1.16.11.1 | not-accessible | This table gives locationing information about the rogue APs | |
| wsCcRfRapLocationingEntry | 1.3.6.1.4.1.388.14.3.2.1.16.11.1.1 | not-accessible | An entry in the rogue AP locationing table | |
| INT wsCcRfRapLocationingIndex | 1.3.6.1.4.1.388.14.3.2.1.16.11.1.1.1 | INTEGER | read-only | Index of the row |
| PHY wsCcRfRapLocationingAPMac | 1.3.6.1.4.1.388.14.3.2.1.16.11.1.1.2 | PhysAddress | read-only | MAC address of the rogue AP |
| PHY wsCcRfRapLocationingRadioMac | 1.3.6.1.4.1.388.14.3.2.1.16.11.1.1.3 | PhysAddress | read-only | MAC address of the radio which heard this rogue AP beacon |
| I32 wsCcRfRapLocationingSignalStrength | 1.3.6.1.4.1.388.14.3.2.1.16.11.1.1.4 | Integer32 | read-only | Signal Strength in dBm of the beacon from the rogue AP |
| I32 wsCcRfRapLocationingHeardChannel | 1.3.6.1.4.1.388.14.3.2.1.16.11.1.1.5 | Integer32 | read-only | Channel on which the beacon from the rogue AP was heard |
| TIK wsCcRfRapLocationingHeardTime | 1.3.6.1.4.1.388.14.3.2.1.16.11.1.1.6 | TimeTicks | read-only | Time in timeticks (since boot) when the rogue AP beacon was heard |
| T/F wsCcRfRapLocationingEnable | 1.3.6.1.4.1.388.14.3.2.1.16.11.2 | TruthValue | read-write | Enable/Disable rogue AP locationing |
| I32 wsCcRfRapLocationingMaxRap | 1.3.6.1.4.1.388.14.3.2.1.16.11.3 | Integer32 | read-write | Maximum number of Rogue APs in the table. |
| I32 wsCcRfRapLocationingScanInterval | 1.3.6.1.4.1.388.14.3.2.1.16.11.4 | Integer32 | read-write | Time interval between two scans in seconds |
| I32 wsCcRfRapLocationingScanTime | 1.3.6.1.4.1.388.14.3.2.1.16.11.5 | Integer32 | read-write | Duration (dwell time) of scan in milliseconds |
| STR wsCcRfRapLocationingChannelSetForRadioA | 1.3.6.1.4.1.388.14.3.2.1.16.11.6 | DisplayString | read-write | Channel Set for 802.11a radio |
| STR wsCcRfRapLocationingChannelSetForRadioBG | 1.3.6.1.4.1.388.14.3.2.1.16.11.7 | DisplayString | read-write | Channel Set for 802.11bg radio |
| I32 wsCcRfRapLocationingNumRap | 1.3.6.1.4.1.388.14.3.2.1.16.11.8 | Integer32 | read-only | Current number of Rogue APs in the table. |
| DOA wsCcRfRapLocationingClear | 1.3.6.1.4.1.388.14.3.2.1.16.11.9 | DoActionNow | read-write | Erase the contents of rogue AP locationing table |
| wsCcRfRapContainment | 1.3.6.1.4.1.388.14.3.2.1.16.12 | |||
| T/F wsCcRfRapContainmentEnable | 1.3.6.1.4.1.388.14.3.2.1.16.12.1 | TruthValue | read-write | Enable Rogue AP Containment |
| U32 wsCcRfRapContainmentInterval | 1.3.6.1.4.1.388.14.3.2.1.16.12.2 | Unsigned32 | read-write | Set the interval for broadcast 802.11 de-authentication. |
| wsCcRfRapContainmentTable | 1.3.6.1.4.1.388.14.3.2.1.16.12.3 | not-accessible | The table of Rogue AP (MACs) configured for Containment, | |
| wsCcRfRapContainmentEntry | 1.3.6.1.4.1.388.14.3.2.1.16.12.3.1 | not-accessible | Entries in the Rogue AP Containment Table | |
| INT wsCcRfRapContainmentIndex | 1.3.6.1.4.1.388.14.3.2.1.16.12.3.1.1 | INTEGER | read-only | Rogue AP Containment Table Index |
| PHY wsCcRfRapContainmentRogueMac | 1.3.6.1.4.1.388.14.3.2.1.16.12.3.1.2 | PhysAddress | read-create | BSS MAC of the Rogue AP which is to be Contained. |
| U32 wsCcRfRapContainmentFinderCount | 1.3.6.1.4.1.388.14.3.2.1.16.12.3.1.3 | Unsigned32 | read-only | Indicates the number of finders for a Rogue AP. A Rogue AP report may time out, or the Rogue AP can move to the Approved list. In either case, Containment shall stop for that particular Rogue AP. |
| ABB wsCcRfRapContainmentRowStatus | 1.3.6.1.4.1.388.14.3.2.1.16.12.3.1.4 | AbbrevRowStatus | read-create | Row Status (for Rogue AP Containment Table) |
| U32 wsCcRfRapContainmentReportedChannel | 1.3.6.1.4.1.388.14.3.2.1.16.12.3.1.5 | Unsigned32 | read-only | Channel on which the Rogue Access Point is reported. |
| wsCcRfIds | 1.3.6.1.4.1.388.14.3.2.1.17 | |||
| I32 wsCcRfIdsMaxExcsvAssoc | 1.3.6.1.4.1.388.14.3.2.1.17.1 | Integer32 | read-write | Monitor the number of association requests from mobile- units. |
| I32 wsCcRfIdsMaxExcsvProbes | 1.3.6.1.4.1.388.14.3.2.1.17.2 | Integer32 | read-write | Monitor the number of probe requests from mobile-units. |
| I32 wsCcRfIdsMuFilterAgeOut | 1.3.6.1.4.1.388.14.3.2.1.17.3 | Integer32 | read-write | Set the number of seconds to filter a mobile-unit that set off IDS |
| wsCcRfIdsMax | 1.3.6.1.4.1.388.14.3.2.1.17.4 | |||
| INT wsCcRfIdsMaxExcsvAssos | 1.3.6.1.4.1.388.14.3.2.1.17.4.1 | INTEGER | read-write | Set the limit on the number of association requests from mobile-units. |
| INT wsCcRfIdsMaxExcsvProbs | 1.3.6.1.4.1.388.14.3.2.1.17.4.2 | INTEGER | read-write | Set the limit on the number of probe requests from mobile-units. |
| INT wsCcRfIdsMaxExcsvDisassos | 1.3.6.1.4.1.388.14.3.2.1.17.4.3 | INTEGER | read-write | Set the limit on the number of disassociation requests from mobile-units. |
| INT wsCcRfIdsMaxExcsvAuthFailures | 1.3.6.1.4.1.388.14.3.2.1.17.4.4 | INTEGER | read-write | Set the limit on the number of authentication failures in mobile-units. |
| INT wsCcRfIdsMaxExcsvCryptoReplays | 1.3.6.1.4.1.388.14.3.2.1.17.4.5 | INTEGER | read-write | Set the limit on the number of crypto replays in mobile-units. |
| INT wsCcRfIdsMaxExcsv80211Replays | 1.3.6.1.4.1.388.14.3.2.1.17.4.6 | INTEGER | read-write | Set the limit on the number of 802.11 replays in mobile-units. |
| I32 wsCcRfIdsMaxExcsvDecryptFails | 1.3.6.1.4.1.388.14.3.2.1.17.4.7 | Integer32 | read-write | Set the limit on the number of decryption failures in mobile-units. |
| wsCcRfIdsAnmly | 1.3.6.1.4.1.388.14.3.2.1.17.5 | |||
| INT wsCcRfIdsAnmlySrcMacEqDestMac | 1.3.6.1.4.1.388.14.3.2.1.17.5.1 | INTEGER | read-write | When enabled, it carries out anomaly detection where source and destination MAC addresses are same in the frame. |
| INT wsCcRfIdsAnmlyNullDestination | 1.3.6.1.4.1.388.14.3.2.1.17.5.2 | INTEGER | read-write | When enabled, it carries out anomaly detection where the destination MAC is NULL. |
| INT wsCcRfIdsAnmlySrcMulticastMac | 1.3.6.1.4.1.388.14.3.2.1.17.5.3 | INTEGER | read-write | When enabled, it carries out anomaly detection where the source MAC address in the frame is a multicast address. |
| INT wsCcRfIdsAnmlyWeakWepIv | 1.3.6.1.4.1.388.14.3.2.1.17.5.4 | INTEGER | read-write | When enabled, it detects the out anomaly where the WEP IV is weak. |
| INT wsCcRfIdsStatusFilteredMacMax | 1.3.6.1.4.1.388.14.3.2.1.17.6 | INTEGER | read-only | Set the maximum number of MACs to be filtered for IDS. |
| INT wsCcRfIdsMuFilterAgeOutTime | 1.3.6.1.4.1.388.14.3.2.1.17.7 | INTEGER | read-write | Set the number of seconds to filter a mobile-unit that set off IDS |
| wsCcRfIdsStatusTable | 1.3.6.1.4.1.388.14.3.2.1.17.8 | not-accessible | A table to track WIDS status for each filtered MAC. | |
| wsCcRfIdsStatusEntry | 1.3.6.1.4.1.388.14.3.2.1.17.8.1 | not-accessible | An entry in the wsCcRfIdsStatusTable | |
| INT wsCcRfIdsStatusViolatnIndex | 1.3.6.1.4.1.388.14.3.2.1.17.8.1.1 | INTEGER | read-only | The index for this table which tells about at most 100 most recent violations. |
| PHY wsCcRfIdsStatusFilteredMuMac | 1.3.6.1.4.1.388.14.3.2.1.17.8.1.2 | PhysAddress | read-only | The MAC address of the mobile-unit which is being filtered for WIDS. |
| IDS wsCcRfIdsStatusViolatnType | 1.3.6.1.4.1.388.14.3.2.1.17.8.1.3 | IdsViolationType | read-only | The specific violation type done by the MU, whether a threshold was crossed or an anomaly was detected. |
| INT wsCcRfIdsStatusRadioIndex | 1.3.6.1.4.1.388.14.3.2.1.17.8.1.4 | INTEGER | read-only | The radio index where this violation occured. |
| TIK wsCcRfIdsStatusRemainingBlacklistTime | 1.3.6.1.4.1.388.14.3.2.1.17.8.1.5 | TimeTicks | read-only | The remaining blacklist time for this mobile-unit which had a WIDS violation. |
| ROW wsCcRfIdsStatusRowStatus | 1.3.6.1.4.1.388.14.3.2.1.17.8.1.6 | RowStatus | read-create | The row status for this entry. |
| wsCcRfIdsEventTable | 1.3.6.1.4.1.388.14.3.2.1.17.9 | not-accessible | An entry in the wsCcRfIdsEventTable | |
| wsCcRfIdsEventEntry | 1.3.6.1.4.1.388.14.3.2.1.17.9.1 | not-accessible | An entry in the wsCcRfMuIdsTable. | |
| INT wsCcRfIdsEventRadioIndex | 1.3.6.1.4.1.388.14.3.2.1.17.9.1.1 | INTEGER | read-only | The radio index where this event last occured. |
| IDS wsCcRfIdsEventType | 1.3.6.1.4.1.388.14.3.2.1.17.9.1.2 | IdsViolationType | read-only | The event type, which is the index for this table. There are eleven event types enumerated so far and hence this table has eleven rows. |
| TIK wsCcRfIdsEventLastOccurredTime | 1.3.6.1.4.1.388.14.3.2.1.17.9.1.3 | TimeTicks | read-only | Timeticks since the last occurence of this event. |
| I32 wsCcRfIdsEventTotalCount | 1.3.6.1.4.1.388.14.3.2.1.17.9.1.4 | Integer32 | read-only | The total count of how many times a given type of event has occurred in the switch. |
| I32 wsCcRfIdsEventCountSinceMidnight | 1.3.6.1.4.1.388.14.3.2.1.17.9.1.5 | Integer32 | read-only | A count of how many times a given type of event has occurred in the switch since midnight i.e. 00:00:00 hours. |
| T/F wsCcRfIdsClearMuIdsEventEntries | 1.3.6.1.4.1.388.14.3.2.1.17.10 | TruthValue | read-write | A scalar to reset all entries in the wsCcRfIdsMuEventTable to 0 |
| INT wsCcRfIdsEventPeriod | 1.3.6.1.4.1.388.14.3.2.1.17.11 | INTEGER | read-write | The period of time, in seconds, over which the IDS events are observed to check if they exceeded the threshold. For example if this value is set as 5 seconds, the threshold for, say, excessive authentication failures can be, say, 100 event detections per 5 second interval. |
| U32 wsCcRfIdsDetectionWindow | 1.3.6.1.4.1.388.14.3.2.1.17.12 | Unsigned32 | read-write | Number of seconds for detection. |
| wsCcRfIdsThresholdsTable | 1.3.6.1.4.1.388.14.3.2.1.17.13 | not-accessible | Thresholds and filter-ageout for each violation type. | |
| wsCcRfIdsThresholdsEntry | 1.3.6.1.4.1.388.14.3.2.1.17.13.1 | not-accessible | An entry in the wsCcRfIdsThresholdsTable. | |
| IDS wsCcRfIdsThresholdsViolTypeIndex | 1.3.6.1.4.1.388.14.3.2.1.17.13.1.1 | IdsViolationType | read-write | Description. |
| U32 wsCcRfIdsThresholdsMu | 1.3.6.1.4.1.388.14.3.2.1.17.13.1.2 | Unsigned32 | read-write | MU threshold for violation type. Setting the value to 0 will disable the check. |
| U32 wsCcRfIdsThresholdsRadio | 1.3.6.1.4.1.388.14.3.2.1.17.13.1.3 | Unsigned32 | read-write | Radio threshold for violation type. Setting the value to 0 will disable the check. |
| U32 wsCcRfIdsThresholdsSwitch | 1.3.6.1.4.1.388.14.3.2.1.17.13.1.4 | Unsigned32 | read-write | Switch threshold for violation type. Setting the value to 0 will disable the check. |
| U32 wsCcRfIdsThresholdsFilterAgeout | 1.3.6.1.4.1.388.14.3.2.1.17.13.1.5 | Unsigned32 | read-write | Number of seconds to filter for violation type. |
| I32 wsCcRfIdsRadioIndex | 1.3.6.1.4.1.388.14.3.2.1.17.14 | Integer32 | read-only | The radio index where this event last occured. |
| IDS wsCcRfIdsViolationType | 1.3.6.1.4.1.388.14.3.2.1.17.15 | IdsViolationType | read-only | The specific type of the IDS violation has occured. |
| I32 wsCcRfIdsViolCountLastDetWindow | 1.3.6.1.4.1.388.14.3.2.1.17.16 | Integer32 | read-only | The number of IDS violations has occured in the last detection window. |
| wsCcRfIdsBadEssidTable | 1.3.6.1.4.1.388.14.3.2.1.17.17 | not-accessible | Bad Essid Table. To be used for configuring bad essid frame anomaly detection in IDS feature. | |
| wsCcRfIdsBadEssidEntry | 1.3.6.1.4.1.388.14.3.2.1.17.17.1 | not-accessible | A bad essid string entry. Upto 10 are allowed. | |
| INT wsCcRfIdsBadEssidIndex | 1.3.6.1.4.1.388.14.3.2.1.17.17.1.1 | INTEGER | read-only | Index of the bad ESSID string. |
| STR wsCcRfIdsBadEssid | 1.3.6.1.4.1.388.14.3.2.1.17.17.1.2 | DisplayString | read-create | Bad ESSID string. |
| ABB wsCcRfIdsBadEssidRowStatus | 1.3.6.1.4.1.388.14.3.2.1.17.17.1.3 | AbbrevRowStatus | read-create | Row status: only createAndGo(4) and delete(6) are supported. |
| wsCcRfSelfHealing | 1.3.6.1.4.1.388.14.3.2.1.18 | |||
| T/F wsCcRfSelfHealingNeighborRecoveryEnable | 1.3.6.1.4.1.388.14.3.2.1.18.1 | TruthValue | read-write | Enable/Disable monitoring of APs and attempt to increase coverage on failure. |
| DOA wsCcRfSelfHealingDetectNeighborNow | 1.3.6.1.4.1.388.14.3.2.1.18.2 | DoActionShowProgress | read-write | Disassociate all MUs, clear current neigbors and run a neighbor detection |
| T/F wsCcRfSelfHealingInterferenceAvoidanceEnable | 1.3.6.1.4.1.388.14.3.2.1.18.3 | TruthValue | read-write | Enable/disable interference avoidance. |
| I32 wsCcRfSelfHealingInterferenceAvoidanceRetriesx10 | 1.3.6.1.4.1.388.14.3.2.1.18.4 | Integer32 | read-write | The average number retries (x10) to cause a radio to re-run auto channel selection. |
| I32 wsCcRfSelfHealingInterferenceAvoidanceHoldTime | 1.3.6.1.4.1.388.14.3.2.1.18.5 | Integer32 | read-write | The number of seconds to disable interference avoidance after a detection. This prevents a radio from changing channels continuously. |
| wsCcRfSelfHealingNeighborRadioTable | 1.3.6.1.4.1.388.14.3.2.1.18.6 | not-accessible | This table stores radio neighbor information. | |
| wsCcRfSelfHealingNeighborRadioEntry | 1.3.6.1.4.1.388.14.3.2.1.18.6.1 | not-accessible | ||
| OCT wsCcRfSelfHealingNeighborRadioIndices | 1.3.6.1.4.1.388.14.3.2.1.18.6.1.1 | OCTET STRING | read-write | Indices of Neighbor Radios. field octets contents range ----- ------ -------- ----- 1 1-2 Count of indices 0..16 2-17 3-34 Neighbor Radio Indices 0..4096 for each index ---------------------------------------------------------------------------------- | Count (2 octets) | Neighbor Radio Indices ( 2 octets times 16 occurrences | ---------------------------------------------------------------------------------- All octets are in network byte order. Definition of contents: Count of indices: The number of Neighbor Radio Indices following. Neighbor Radios Indices: Each Neighbor Radios Index takes 2 octets. There are 16 Neighbor Radio Indices. Unused Neighbor Radios Indices will have the value zero. |
| wsCcRfSelfHealingMonitoringTable | 1.3.6.1.4.1.388.14.3.2.1.18.7 | not-accessible | ||
| wsCcRfSelfHealingMonitoringEntry | 1.3.6.1.4.1.388.14.3.2.1.18.7.1 | not-accessible | ||
| I32 wsCcRfSelfHealingMonitoringTransRadio | 1.3.6.1.4.1.388.14.3.2.1.18.7.1.1 | Integer32 | accessible-for-notify | Index of transmitting radio. |
| I32 wsCcRfSelfHealingMonitoringRecvRadio | 1.3.6.1.4.1.388.14.3.2.1.18.7.1.2 | Integer32 | accessible-for-notify | Index of receiving Radio. |
| I32 wsCcRfSelfHealingMonitoringChannel | 1.3.6.1.4.1.388.14.3.2.1.18.7.1.3 | Integer32 | read-only | Monitoring channel |
| TIK wsCcRfSelfHealingMonitoringLastTime | 1.3.6.1.4.1.388.14.3.2.1.18.7.1.4 | TimeTicks | read-only | The time of the last beacon heard |
| I32 wsCcRfSelfHealingMonitoringLastSignal | 1.3.6.1.4.1.388.14.3.2.1.18.7.1.5 | Integer32 | read-only | The dBm signal value of the last beacon heard |
| I32 wsCcRfSelfHealingMonitoringMinSig | 1.3.6.1.4.1.388.14.3.2.1.18.7.1.6 | Integer32 | read-only | The lowest dBm signal value heard |
| I32 wsCcRfSelfHealingMonitoringMaxSig | 1.3.6.1.4.1.388.14.3.2.1.18.7.1.7 | Integer32 | read-only | The highest dBm signal value heard |
| I32 wsCcRfSelfHealingMonitoringSumSig | 1.3.6.1.4.1.388.14.3.2.1.18.7.1.8 | Integer32 | read-only | The sum of all signal values heard |
| U32 wsCcRfSelfHealingMonitoringNumSig | 1.3.6.1.4.1.388.14.3.2.1.18.7.1.9 | Unsigned32 | read-only | The number of signal values heard |
| wsCcRfHotspot | 1.3.6.1.4.1.388.14.3.2.1.19 | |||
| wsCcRfHotspotTable | 1.3.6.1.4.1.388.14.3.2.1.19.1 | not-accessible | Configure hotspot related parameters. | |
| wsCcRfHotspotEntry | 1.3.6.1.4.1.388.14.3.2.1.19.1.1 | not-accessible | ||
| IP wsCcRfHotspotServerIp1 | 1.3.6.1.4.1.388.14.3.2.1.19.1.1.1 | IpAddress | read-write | Primary Radius server ip for hotspot authentication. |
| I32 wsCcRfHotspotServerPort1 | 1.3.6.1.4.1.388.14.3.2.1.19.1.1.2 | Integer32 | read-write | Primary Radius server port for hotspot authentication. |
| PAS wsCcRfHotspotServerSecret1 | 1.3.6.1.4.1.388.14.3.2.1.19.1.1.3 | Password | read-write | Primary Radius server shared secret for hotspot authentication. |
| IP wsCcRfHotspotServerIp2 | 1.3.6.1.4.1.388.14.3.2.1.19.1.1.4 | IpAddress | read-write | Secondary Radius server ip for hotspot authentication. |
| I32 wsCcRfHotspotServerPort2 | 1.3.6.1.4.1.388.14.3.2.1.19.1.1.5 | Integer32 | read-write | Secondary Radius server port for hotspot authentication. |
| PAS wsCcRfHotspotServerSecret2 | 1.3.6.1.4.1.388.14.3.2.1.19.1.1.6 | Password | read-write | Secondary Radius server shared secret for hotspot authentication. |
| I32 wsCcRfHotspotServerRetries | 1.3.6.1.4.1.388.14.3.2.1.19.1.1.7 | Integer32 | read-write | Number of retries the wireless switch initiates before giving up |
| I32 wsCcRfHotspotServerTimeout | 1.3.6.1.4.1.388.14.3.2.1.19.1.1.8 | Integer32 | read-write | Time the wireless switch waits for a response from the radius server before retrying |
| INT wsCcRfHotspotPageLocation | 1.3.6.1.4.1.388.14.3.2.1.19.1.1.9 | INTEGER | read-write | The location of the webpages to be used for authentication. These pages can either be hosted on the wireless switch or on an external web server |
| INT wsCcRfHotspotWebsiteType | 1.3.6.1.4.1.388.14.3.2.1.19.1.1.10 | INTEGER | read-write | The website type to be used for authentication. The website can either be hosted on the wireless switch or on an external web server |
| INT wsCcRfHotspotMode | 1.3.6.1.4.1.388.14.3.2.1.19.1.1.11 | INTEGER | read-write | The hotspot mode for a WLAN. This should be set to 'webPortalBased' to use customer-specific portal. |
| T/F wsCcRfHotspotLogoutOnClose | 1.3.6.1.4.1.388.14.3.2.1.19.1.1.12 | TruthValue | read-write | This property allows end user to enable/disable user logout on browser close event. |
| INT wsCcRfHotspotMaxLoginAttempts | 1.3.6.1.4.1.388.14.3.2.1.19.1.1.13 | INTEGER | read-write | This property allows end user to specify Maximum login attempts that can be allowed before user is denied any access. |
| T/F wsCcRfHotspotRedirectToHostName | 1.3.6.1.4.1.388.14.3.2.1.19.1.1.14 | TruthValue | read-write | Enable or disable the use of hostname/System-Name in the redirection URL instead of the IP address of the switch. |
| INT wsCcRfHotspotSimultaneousUsers | 1.3.6.1.4.1.388.14.3.2.1.19.1.1.15 | INTEGER | read-write | The number of MAC addresses that are allowed to use same username at the same time in hotspot |
| wsCcRfHotspotPageTable | 1.3.6.1.4.1.388.14.3.2.1.19.2 | not-accessible | Configure hotspot page parameters | |
| wsCcRfHotspotPageEntry | 1.3.6.1.4.1.388.14.3.2.1.19.2.1 | not-accessible | ||
| INT wsCcRfHotspotPageType | 1.3.6.1.4.1.388.14.3.2.1.19.2.1.1 | INTEGER | accessible-for-notify | Hotspot page type |
| OCT wsCcRfHotspotIntPageTitle | 1.3.6.1.4.1.388.14.3.2.1.19.2.1.2 | OCTET STRING | read-write | Ascii string that will be in the title of the webpage. |
| OCT wsCcRfHotspotIntPageHeader | 1.3.6.1.4.1.388.14.3.2.1.19.2.1.3 | OCTET STRING | read-write | Ascii string that is displayed as a header. (large font, top section) of the webpage. |
| OCT wsCcRfHotspotIntPageDescr | 1.3.6.1.4.1.388.14.3.2.1.19.2.1.4 | OCTET STRING | read-write | Ascii string that is displayed as the main body (normal font, middle of page) of the webpage |
| OCT wsCcRfHotspotIntPageFooter | 1.3.6.1.4.1.388.14.3.2.1.19.2.1.5 | OCTET STRING | read-write | Ascii string that is displayed at the footer (smaller font, bottom section) of the webpage |
| OCT wsCcRfHotspotIntPageImgUrl1 | 1.3.6.1.4.1.388.14.3.2.1.19.2.1.6 | OCTET STRING | read-write | main image( large size) that will be served up by the local webpage. Appears between the header and description on the webpage. |
| OCT wsCcRfHotspotIntPageImgUrl2 | 1.3.6.1.4.1.388.14.3.2.1.19.2.1.7 | OCTET STRING | read-write | Small image (thumbnail size) that will be served up by the local webpage. Appears near the footer on the webpage. |
| OCT wsCcRfHotspotExtPageUrl | 1.3.6.1.4.1.388.14.3.2.1.19.2.1.8 | OCTET STRING | read-write | Url of external page |
| wsCcRfHotspotWhiteIpTable | 1.3.6.1.4.1.388.14.3.2.1.19.3 | not-accessible | Configure hotspot white list parameters. Users who have not yet authenticated will be allowed access to these IP addresses | |
| wsCcRfHotspotWhiteIpEntry | 1.3.6.1.4.1.388.14.3.2.1.19.3.1 | not-accessible | ||
| I32 wsCcRfHotspotWhiteIpRuleIndex | 1.3.6.1.4.1.388.14.3.2.1.19.3.1.1 | Integer32 | accessible-for-notify | rule index |
| IP wsCcRfHotspotWhiteIpAddr | 1.3.6.1.4.1.388.14.3.2.1.19.3.1.2 | IpAddress | read-write | White-list IP address |
| wsCcRfQos | 1.3.6.1.4.1.388.14.3.2.1.20 | |||
| wsCcRfQosAcTo802dot1pTable | 1.3.6.1.4.1.388.14.3.2.1.20.1 | not-accessible | The mapping of access categories to 802.1p priorities. | |
| wsCcRfQosAcTo802dot1pEntry | 1.3.6.1.4.1.388.14.3.2.1.20.1.1 | not-accessible | A single mapping of an access category to 802.1p priority. | |
| OID wsCcRfQosAcTo802dot1pAccessCategory | 1.3.6.1.4.1.388.14.3.2.1.20.1.1.1 | TrafficIdentifier | accessible-for-notify | An access category. |
| I32 wsCcRfQosAcTo802dot1pPriority | 1.3.6.1.4.1.388.14.3.2.1.20.1.1.2 | Integer32 | read-write | An 802.1p priority tag. |
| wsCcRfQos802dot1pToAcTable | 1.3.6.1.4.1.388.14.3.2.1.20.2 | not-accessible | The mapping of 802.1p priorities to access categories . | |
| wsCcRfQos802dot1pToAcEntry | 1.3.6.1.4.1.388.14.3.2.1.20.2.1 | not-accessible | A single mapping of an 802.1p priority to an access category. | |
| I32 wsCcRfQos802dot1pToAcIndex | 1.3.6.1.4.1.388.14.3.2.1.20.2.1.1 | Integer32 | accessible-for-notify | A simple sequential index. |
| I32 wsCcRfQos802dot1pToAcPriority | 1.3.6.1.4.1.388.14.3.2.1.20.2.1.2 | Integer32 | read-only | An 802.1p priority tag. |
| OID wsCcRfQos802dot1pToAcAccessCategory | 1.3.6.1.4.1.388.14.3.2.1.20.2.1.3 | TrafficIdentifier | read-write | An access category. |
| wsCcRfQosDscpToAcTable | 1.3.6.1.4.1.388.14.3.2.1.20.3 | not-accessible | The mapping of DSCP values to access categories. | |
| wsCcRfQosDscpToAcEntry | 1.3.6.1.4.1.388.14.3.2.1.20.3.1 | not-accessible | A single mapping of a DSCP value to an access category. | |
| I32 wsCcRfQosDscpToAcIndex | 1.3.6.1.4.1.388.14.3.2.1.20.3.1.1 | Integer32 | accessible-for-notify | A simple sequential index. |
| I32 wsCcRfQosDscpToAcDscp | 1.3.6.1.4.1.388.14.3.2.1.20.3.1.2 | Integer32 | read-only | A DSCP value. |
| OID wsCcRfQosDscpToAcAccessCategory | 1.3.6.1.4.1.388.14.3.2.1.20.3.1.3 | TrafficIdentifier | read-write | An access category. |
| wsCcRfWiredWebAuth | 1.3.6.1.4.1.388.14.3.2.1.21 | |||
| T/F wsCcRfWiredWebAuthEnable | 1.3.6.1.4.1.388.14.3.2.1.21.1 | TruthValue | read-write | Enabling of wired web authentication. |
| INT wsCcRfWiredWebAuthVlan | 1.3.6.1.4.1.388.14.3.2.1.21.2 | INTEGER | read-write | Assignment of VLAN to the wired web authentication. |
| INT wsCcRfWiredWebAuthWlan | 1.3.6.1.4.1.388.14.3.2.1.21.3 | INTEGER | read-write | Assignment of WLAN to the wired web authentication. |
| I32 wsCcRfWiredWebAuthHostEntryDelete | 1.3.6.1.4.1.388.14.3.2.1.21.4 | Integer32 | read-write | Description.Use this object to remove an entry in wsCcRfWiredWebAuthHostTable. |
| wsCcRfWiredWebAuthHostTable | 1.3.6.1.4.1.388.14.3.2.1.21.5 | not-accessible | Description. | |
| wsCcRfWiredWebAuthHostEntry | 1.3.6.1.4.1.388.14.3.2.1.21.5.1 | not-accessible | Description. | |
| INT wsCcRfWiredWebAuthHostIndex | 1.3.6.1.4.1.388.14.3.2.1.21.5.1.1 | INTEGER | read-only | Description. The index for the wsCcRfWiredWebAuthHostTable. |
| PHY wsCcRfWiredWebAuthHostMac | 1.3.6.1.4.1.388.14.3.2.1.21.5.1.2 | PhysAddress | read-only | Description.The Mac Address of this wsCcRfWiredWebAuthHostEntry |
| IP wsCcRfWiredWebAuthHostIp | 1.3.6.1.4.1.388.14.3.2.1.21.5.1.3 | IpAddress | read-only | Description. The IP address of this wsCcRfWiredWebAuthHosEntry |
| INT wsCcRfWiredWebAuthHostState | 1.3.6.1.4.1.388.14.3.2.1.21.5.1.4 | INTEGER | read-only | Description.The current state of this wsCcRfWiredWebAuthHostEntry |
| I32 wsCcRfWiredWebAuthHostVlan | 1.3.6.1.4.1.388.14.3.2.1.21.5.1.5 | Integer32 | read-only | Description.The Vlan assigned to this wsCcRfWiredWebAuthHostEntry |
| wsCcRfLldp | 1.3.6.1.4.1.388.14.3.2.1.22 | |||
| STR wsCcRfLldpName | 1.3.6.1.4.1.388.14.3.2.1.22.1 | DisplayString | read-write | LLDP friendly name to be used in LLDP for adopted radio-ports. |
| PHY wsCcRfLldpApMacAddr | 1.3.6.1.4.1.388.14.3.2.1.22.2 | PhysAddress | read-write | The Mac address to be associated with LLDP friendly name. |
| INT wsCcRfLldpNameSet | 1.3.6.1.4.1.388.14.3.2.1.22.3 | INTEGER | read-write | Configure the LLDP friendly name to be used in LLDP for adopted radio-ports. If wsCcRfLldpApMacAddr is not specified, the LLDP friendly name update will be sent to all currently adpoted radio ports. |
| STR wsCcRfLastAlarmEvent | 1.3.6.1.4.1.388.14.3.2.1.23 | DisplayString | read-only | An event which could be one of the following: AP shut down AP channel configuration is changed Interference on current channel is detected Radius authentication server is unreachable/unavailable/unconnected Radius accounting server cannot be connected Portal server is unavailable AP is disconnected from the network |
| wsCcRfApExt | 1.3.6.1.4.1.388.14.3.2.1.24 | |||
| wsCcRfApExtTable | 1.3.6.1.4.1.388.14.3.2.1.24.1 | not-accessible | Description. | |
| wsCcRfApExtEntry | 1.3.6.1.4.1.388.14.3.2.1.24.1.1 | not-accessible | Description. | |
| PHY wsCcRfApExtApMac | 1.3.6.1.4.1.388.14.3.2.1.24.1.1.1 | PhysAddress | read-only | Description. |
| IP wsCcRfApExtNetMask | 1.3.6.1.4.1.388.14.3.2.1.24.1.1.2 | IpAddress | read-only | The network mask of this Access port. |
| U32 wsCcRfApExtTotalInterfaces | 1.3.6.1.4.1.388.14.3.2.1.24.1.1.3 | Unsigned32 | read-only | The total number of physical interfaces of this Access port. |
| STR wsCcRfApExtApName | 1.3.6.1.4.1.388.14.3.2.1.24.1.1.4 | DisplayString | read-write | The name of the AP. |
| STR wsCcRfApExtApLocation | 1.3.6.1.4.1.388.14.3.2.1.24.1.1.5 | DisplayString | read-write | The location of the AP. |
| OCT wsCcRfApExtSecureModeSecret | 1.3.6.1.4.1.388.14.3.2.1.24.1.1.6 | OCTET STRING | read-write | Configure a shared secret for an AP. |
| T/F wsCcRfApExtSecureModeEnable | 1.3.6.1.4.1.388.14.3.2.1.24.1.1.7 | TruthValue | read-write | Configure secured mode for this AP. If secure-mode is set to enable it means that the WISP-e for this AP will be secured. |
| T/F wsCcRfApExtSecureModeStagingEnable | 1.3.6.1.4.1.388.14.3.2.1.24.1.1.8 | TruthValue | read-write | Configure secure mode staging to an AP. In this mode the switch will send configured shared secret in the clear in the Join response to the AP. |
| OCT wsCcRfApExtSecureWispeDefSecret | 1.3.6.1.4.1.388.14.3.2.1.24.2 | OCTET STRING | read-write | Configure default shared secret for secure wisp-e. |
| STR wsCcRfSwitchManufacturer | 1.3.6.1.4.1.388.14.3.2.1.25 | DisplayString | read-only | The manufacturer of the switch or AC (access controller) |
| wsCcRfApConvert | 1.3.6.1.4.1.388.14.3.2.1.26 | |||
| I32 wsCcRfApConvertIndex | 1.3.6.1.4.1.388.14.3.2.1.26.1 | Integer32 | read-write | The valid AP index to be converted. |
| INT wsCcRfApConvertType | 1.3.6.1.4.1.388.14.3.2.1.26.2 | INTEGER | read-write | Convert AP to default or sensor. |
| INT wsCcRfApConvertAction | 1.3.6.1.4.1.388.14.3.2.1.26.3 | INTEGER | read-write | Both wsCcRfApConvertIndex and wsCcRfApConvertType should be properly set before setting this object. |
| wsCcRfSensor | 1.3.6.1.4.1.388.14.3.2.1.27 | |||
| wsCcRfSensorRevert | 1.3.6.1.4.1.388.14.3.2.1.27.1 | |||
| I32 wsCcRfSensorRevertIndex | 1.3.6.1.4.1.388.14.3.2.1.27.1.1 | Integer32 | read-write | The valid sensor index to be reverted to AP. |
| INT wsCcRfSensorRevertAction | 1.3.6.1.4.1.388.14.3.2.1.27.1.2 | INTEGER | read-write | wsCcRfSensorRevertIndex should be properly set before setting this object. |
| INT wsCcRfSensorRevertVlan | 1.3.6.1.4.1.388.14.3.2.1.27.1.3 | INTEGER | read-write | Configure vlans where sensors are to be discovered. 0 indicates no vlans exists. |
| wsCcRfSensorRevertSensorTable | 1.3.6.1.4.1.388.14.3.2.1.27.1.4 | not-accessible | This table contains a list of sensors that were previoulsy converted from APs. | |
| wsCcRfSensorRevertSensorEntry | 1.3.6.1.4.1.388.14.3.2.1.27.1.4.1 | not-accessible | Description. | |
| INT wsCcRfSensorRevertSensorIndex | 1.3.6.1.4.1.388.14.3.2.1.27.1.4.1.1 | INTEGER | accessible-for-notify | The sensor index. |
| PHY wsCcRfSensorRevertSensorMac | 1.3.6.1.4.1.388.14.3.2.1.27.1.4.1.2 | PhysAddress | read-only | The physical address of this sensor. |
| I32 wsCcRfSensorRevertSensorVlan | 1.3.6.1.4.1.388.14.3.2.1.27.1.4.1.3 | Integer32 | read-only | The assinged Vlan ID for this sensor. |
| IP wsCcRfSensorRevertSensorIp | 1.3.6.1.4.1.388.14.3.2.1.27.1.4.1.4 | IpAddress | read-only | The IP address of this sensor. |
| U32 wsCcRfSensorRevertSensorLastHeard | 1.3.6.1.4.1.388.14.3.2.1.27.1.4.1.5 | Unsigned32 | read-only | Seconds since last heard from the sensor. |
| wsCcRfSensorCfg | 1.3.6.1.4.1.388.14.3.2.1.27.2 | |||
| IP wsCcRfSensorCfgWipsServerPrimaryIp | 1.3.6.1.4.1.388.14.3.2.1.27.2.1 | IpAddress | read-write | The primary IP address of the WIPS server |
| IP wsCcRfSensorCfgWipsServerSecondaryIp | 1.3.6.1.4.1.388.14.3.2.1.27.2.2 | IpAddress | read-write | The secondary IP address of the WIPS server |
| wsCcRfSmart | 1.3.6.1.4.1.388.14.3.2.1.28 | |||
| wsCcRfSmartEnable | 1.3.6.1.4.1.388.14.3.2.1.28.1 | |||
| T/F wsCcRfSmartEnableSmartRF | 1.3.6.1.4.1.388.14.3.2.1.28.1.1 | TruthValue | read-write | Enable or disable Smart-RF functionality. |
| T/F wsCcRfSmartEnableDetectorAssign | 1.3.6.1.4.1.388.14.3.2.1.28.1.2 | TruthValue | read-write | Enable or disable automatic assignment of radio detectors. |
| T/F wsCcRfSmartEnableChannelAssign | 1.3.6.1.4.1.388.14.3.2.1.28.1.3 | TruthValue | read-write | Enable or disable automatic assignment of channels to working radios to avoid channel overlap and avoid interference from external RF sources. |
| T/F wsCcRfSmartEnablePowerAssign | 1.3.6.1.4.1.388.14.3.2.1.28.1.4 | TruthValue | read-write | Enable or disable automatic assignment of transmit power. |
| T/F wsCcRfSmartEnableRescuerAssign | 1.3.6.1.4.1.388.14.3.2.1.28.1.5 | TruthValue | read-write | Enable or disable automatic assignment of rescuers along with rescuing power. |
| T/F wsCcRfSmartEnableFaultyRadioRecover | 1.3.6.1.4.1.388.14.3.2.1.28.1.6 | TruthValue | read-write | Enable or disable monitoring for defective radio and self-healing by its rescuer. |
| T/F wsCcRfSmartEnableInterferenceRecover | 1.3.6.1.4.1.388.14.3.2.1.28.1.7 | TruthValue | read-write | Enable or disable monitoring for interference and self-healing it by rescuer. |
| T/F wsCcRfSmartEnableCoverageHoleRecover | 1.3.6.1.4.1.388.14.3.2.1.28.1.8 | TruthValue | read-write | Enable or disable monitoring and recovering for coverage hole. |
| T/F wsCcRfSmartEnableScheduledCalibration | 1.3.6.1.4.1.388.14.3.2.1.28.1.9 | TruthValue | read-write | Enable or disable scheduled Smart-RF calibration. |
| T/F wsCcRfSmartEnableVerboseMode | 1.3.6.1.4.1.388.14.3.2.1.28.1.10 | TruthValue | read-write | Enables or disables RF smart verbose mode. |
| T/F wsCcRfSmartEnableExtensiveScanMode | 1.3.6.1.4.1.388.14.3.2.1.28.1.11 | TruthValue | read-write | Enables or disables RF smart extensive scan mode. |
| wsCcRfSmartRadioTable | 1.3.6.1.4.1.388.14.3.2.1.28.2 | not-accessible | Table of radio specific configuration for Smart-RF Management. | |
| wsCcRfSmartRadioEntry | 1.3.6.1.4.1.388.14.3.2.1.28.2.1 | not-accessible | An entry in the table. | |
| PHY wsCcRfSmartRadioMac | 1.3.6.1.4.1.388.14.3.2.1.28.2.1.1 | PhysAddress | read-only | The MAC address of the radio. |
| I32 wsCcRfSmartRadioCfgIndex | 1.3.6.1.4.1.388.14.3.2.1.28.2.1.2 | Integer32 | read-only | The configuration index for this radio. |
| T/F wsCcRfSmartRadioEnableDetectorLock | 1.3.6.1.4.1.388.14.3.2.1.28.2.1.3 | TruthValue | read-write | Enable or disable radio detector mode lock of this radio. |
| T/F wsCcRfSmartRadioEnableChannelLock | 1.3.6.1.4.1.388.14.3.2.1.28.2.1.4 | TruthValue | read-write | Enable or disable channel lock of this radio. |
| T/F wsCcRfSmartRadioEnablePowerLock | 1.3.6.1.4.1.388.14.3.2.1.28.2.1.5 | TruthValue | read-write | Enable or disable power lock of this radio. |
| T/F wsCcRfSmartRadioEnableRescuerLock | 1.3.6.1.4.1.388.14.3.2.1.28.2.1.6 | TruthValue | read-write | Enable or disable rescuer lock of this radio. |
| RAD wsCcRfSmartRadioAntGain | 1.3.6.1.4.1.388.14.3.2.1.28.2.1.7 | RadioAntennaGain | read-write | Antenna gain. Please see the definition of RadioAntennaGain for additional information. |
| TRA wsCcRfSmartRadioCovRate | 1.3.6.1.4.1.388.14.3.2.1.28.2.1.8 | TransmitRate | read-write | The desired coverage rate. |
| IP wsCcRfSmartRadioSwichIpAddr | 1.3.6.1.4.1.388.14.3.2.1.28.2.1.9 | IpAddress | read-only | The IP Address of the switch this radio is adopted. |
| U32 wsCcRfSmartRadioCurrChannel | 1.3.6.1.4.1.388.14.3.2.1.28.2.1.10 | Unsigned32 | read-only | The current channel (may be different from configured channel due to DFS etc). A value of 0 for this object implies that the radio is not adopted. |
| INT wsCcRfSmartRadioCurrPower | 1.3.6.1.4.1.388.14.3.2.1.28.2.1.11 | INTEGER | read-only | The output power level for the radio in dBm. A value of 0 for this object implies that the radio is not adopted. |
| INT wsCcRfSmartRadioRetryThrshld | 1.3.6.1.4.1.388.14.3.2.1.28.3 | INTEGER | read-write | Retry threshold is the average number of retries per packet to cause a radio to re-run channel selection. The range in the CLI is 0.0 to 15.0. Since SNMP does not support decimal numbers, the range for this object is 0 to 150 and the set value would be divided by 10 by the smart-rf module. |
| wsCcRfSmartRescuerTable | 1.3.6.1.4.1.388.14.3.2.1.28.4 | not-accessible | Table to assign rescuers for radios. Up to 5 rescuers per radio can be assigned. | |
| wsCcRfSmartRescuerEntry | 1.3.6.1.4.1.388.14.3.2.1.28.4.1 | not-accessible | An entry in the table. | |
| PHY wsCcRfSmartRescuerMac | 1.3.6.1.4.1.388.14.3.2.1.28.4.1.1 | PhysAddress | read-only | Radio MAC of rescuer. |
| U32 wsCcRfSmartRescuerPowerBoost | 1.3.6.1.4.1.388.14.3.2.1.28.4.1.2 | Unsigned32 | read-create | Power raised by the rescuer to cover the radio's coverage, if the radio becomes defective. |
| U32 wsCcRfSmartRescuerAttenuation | 1.3.6.1.4.1.388.14.3.2.1.28.4.1.3 | Unsigned32 | read-create | Attenuation from the rescuer radio to this radio. This column is optional. |
| ABB wsCcRfSmartRescuerRowStatus | 1.3.6.1.4.1.388.14.3.2.1.28.4.1.4 | AbbrevRowStatus | read-create | The Row status. All columns except wsCcRfSmartRescuerAttenuation must be supplied to create a row. The agent itself may also create and/or delete rows, when Smart-RF calibration runs. |
| U32 wsCcRfSmartFaultyRadioNumRescuers | 1.3.6.1.4.1.388.14.3.2.1.28.5 | Unsigned32 | read-write | Number of rescuers to cover a faulty radio. |
| wsCcRfSmartCalibration | 1.3.6.1.4.1.388.14.3.2.1.28.6 | |||
| wsCcRfSmartCalibrationSched | 1.3.6.1.4.1.388.14.3.2.1.28.6.1 | |||
| DAT wsCcRfSmartCalibrationSchedStartTime | 1.3.6.1.4.1.388.14.3.2.1.28.6.1.1 | DateAndTime | read-write | The start-time of the Smart-RF Calibration schedule. It does not have to be a future time. |
| U32 wsCcRfSmartCalibrationSchedIntvl | 1.3.6.1.4.1.388.14.3.2.1.28.6.1.2 | Unsigned32 | read-write | Smart-RF Calibration schedule interval. |
| DOA wsCcRfSmartCalibrationStart | 1.3.6.1.4.1.388.14.3.2.1.28.6.2 | DoActionNow | read-write | Start a new Smart-RF calibration. If calibration fails, wsCcRfSmartCalibrationLastFailedReason will have the reason. |
| STR wsCcRfSmartCalibrationLastFailedReason | 1.3.6.1.4.1.388.14.3.2.1.28.6.3 | DisplayString | read-only | Last calibration failed reason. |
| STR wsCcRfSmartCalibrationStatusMessage | 1.3.6.1.4.1.388.14.3.2.1.28.6.4 | DisplayString | read-only | A message giving the current status of the calibration being performed at the master switch. |
| wsCcRfSmartStatus | 1.3.6.1.4.1.388.14.3.2.1.28.7 | |||
| DAT wsCcRfSmartStatusLastCalStartTime | 1.3.6.1.4.1.388.14.3.2.1.28.7.1 | DateAndTime | read-only | The time the last Smart-RF calibration started. |
| DAT wsCcRfSmartStatusLastCalEndTime | 1.3.6.1.4.1.388.14.3.2.1.28.7.2 | DateAndTime | read-only | The time the last Smart-RF calibration ended. |
| DAT wsCcRfSmartStatusNextCalStartTime | 1.3.6.1.4.1.388.14.3.2.1.28.7.3 | DateAndTime | read-only | The time the next Smart-RF calibration starts. |
| STR wsCcRfSmartStatusCurrOper | 1.3.6.1.4.1.388.14.3.2.1.28.7.4 | DisplayString | read-only | The current Smart-RF operation being done. |
| wsCcRfSmartStatusAssignmentTable | 1.3.6.1.4.1.388.14.3.2.1.28.7.5 | not-accessible | Table of Smart RF assignment history since last calibration. | |
| wsCcRfSmartStatusAssignmentEntry | 1.3.6.1.4.1.388.14.3.2.1.28.7.5.1 | not-accessible | An entry in the table. | |
| U32 wsCcRfSmartStatusAssignmentIndex | 1.3.6.1.4.1.388.14.3.2.1.28.7.5.1.1 | Unsigned32 | read-only | The assignment history sequence number. |
| STR wsCcRfSmartStatusAssignmentEvent | 1.3.6.1.4.1.388.14.3.2.1.28.7.5.1.2 | DisplayString | read-only | Smart RF assignment event. |
| IP wsCcRfSmartMasterSwitchAddr | 1.3.6.1.4.1.388.14.3.2.1.28.7.6 | IpAddress | read-only | The IP address of the master switch. This information is obtained from the clustering daemon and is therefore read-only. |
| T/F wsCcRfSmartIsClusterMaster | 1.3.6.1.4.1.388.14.3.2.1.28.7.7 | TruthValue | read-only | A boolean to represent whether this switch is the cluster master. This information is obtained from the clustering daemon and is therefore read-only. |
| INT wsCcRfSmartScanDwellTime | 1.3.6.1.4.1.388.14.3.2.1.28.8 | INTEGER | read-write | RF smart scan dwell time. |
| wsCcRfSmartRadioNeighborTable | 1.3.6.1.4.1.388.14.3.2.1.28.9 | not-accessible | A table giving details of a radio's neighborhood information. | |
| wsCcRfSmartRadioNeighborEntry | 1.3.6.1.4.1.388.14.3.2.1.28.9.1 | not-accessible | An entry in the neighbor table, indexed by a. the MAC address of the radio b. neighbor index c. tx power | |
| INT wsCcRfSmartRadioNeighborIndex | 1.3.6.1.4.1.388.14.3.2.1.28.9.1.2 | INTEGER | read-only | Neighbor index. |
| INT wsCcRfSmartRadioNeighborTxPower | 1.3.6.1.4.1.388.14.3.2.1.28.9.1.3 | INTEGER | read-only | Tx power of the neighbor radio. |
| U32 wsCcRfSmartRadioNeighborCfgIdx | 1.3.6.1.4.1.388.14.3.2.1.28.9.1.4 | Unsigned32 | read-only | Configuration index of the neighbor radio, taken from its index in the wsCcRfRadioTable. |
| I32 wsCcRfSmartRadioNeighborRxSignal | 1.3.6.1.4.1.388.14.3.2.1.28.9.1.5 | Integer32 | read-only | Rx signal strength of the neighbor radio for the given tx power. |
| I32 wsCcRfSmartRadioNeighborAttenuation | 1.3.6.1.4.1.388.14.3.2.1.28.9.1.6 | Integer32 | read-only | Attenuation of the neighbor radio for the given tx power. |
| PHY wsCcRfSmartRadioNeighborMac | 1.3.6.1.4.1.388.14.3.2.1.28.9.1.7 | PhysAddress | read-only | The MAC address of the neighbor radio. |
| U32 wsCcRfSmartPowerRangeLowerBound | 1.3.6.1.4.1.388.14.3.2.1.28.10 | Unsigned32 | read-write | Lower bound of the transmit power range for automatic assignment. |
| U32 wsCcRfSmartPowerRangeHigherBound | 1.3.6.1.4.1.388.14.3.2.1.28.11 | Unsigned32 | read-write | Higher bound of the transmit power range for automatic assignment. |
| INT wsCcRfSmartRadioHoldTime | 1.3.6.1.4.1.388.14.3.2.1.28.12 | INTEGER | read-write | The number of seconds to disable interference avoidance after a detection. This prevents a radio from changing channels continuously. |
| T/F wsCcRfMasterSyncEnable | 1.3.6.1.4.1.388.14.3.2.1.29 | TruthValue | read-write | Enables or disables the master-sync feature. |
| wsCcRfChannelManager | 1.3.6.1.4.1.388.14.3.2.1.30 | |||
| wsCcRfChannelManagerTable | 1.3.6.1.4.1.388.14.3.2.1.30.1 | not-accessible | A table where the smart-rf and smart-scan capability of each channel can be configured. | |
| wsCcRfChannelManagerEntry | 1.3.6.1.4.1.388.14.3.2.1.30.1.1 | not-accessible | An entry in wsCcRfChannelManagerTable. | |
| INT wsCcRfChannelManagerChan | 1.3.6.1.4.1.388.14.3.2.1.30.1.1.1 | INTEGER | read-only | Channel number |
| T/F wsCcRfChannelManagerSmartRfSel | 1.3.6.1.4.1.388.14.3.2.1.30.1.1.2 | TruthValue | read-write | Whether smart RF is selected for this channel. |
| T/F wsCcRfChannelManagerSmartScanSel | 1.3.6.1.4.1.388.14.3.2.1.30.1.1.3 | TruthValue | read-write | Whether smart scan is selected for this channel. |
| wsCcRfSmartScanWlanMapTable | 1.3.6.1.4.1.388.14.3.2.1.30.2 | not-accessible | A table giving the mapping of radio channels per WLAN with respect to their smart-scan capability. | |
| wsCcRfSmartScanWlanMapEntry | 1.3.6.1.4.1.388.14.3.2.1.30.2.1 | not-accessible | An entry in the wsCcRfSmartScanWlanMapTable. | |
| INT wsCcRfSmartScanWlanMapWlan | 1.3.6.1.4.1.388.14.3.2.1.30.2.1.1 | INTEGER | read-only | The wlan number for the smart scan channel map |
| T/F wsCcRfSmartScanWlanMapSmartScanSel | 1.3.6.1.4.1.388.14.3.2.1.30.2.1.2 | TruthValue | read-write | Whether smart scan is selected for this channel/wlan combination. |
| wsCcRfConformance | 1.3.6.1.4.1.388.14.3.2.1.100 | |||
| wsCcRfCompliances | 1.3.6.1.4.1.388.14.3.2.1.100.1 | |||
| wsCcRfCompliance | 1.3.6.1.4.1.388.14.3.2.1.100.1.1 | |||
| wsCcRfGroups | 1.3.6.1.4.1.388.14.3.2.1.100.2 | |||
| wsCcRfGroup | 1.3.6.1.4.1.388.14.3.2.1.100.2.1 | |||
| wsCcRfDeprecatedGroup | 1.3.6.1.4.1.388.14.3.2.1.100.2.2 | Group of deprecated objects. |
RFC description
Manages wireless RF features in Symbol wireless controllers including smart radio calibration and AP containment.
Start monitoring Symbol Technologies wireless LAN controller (RF-domain channel/power config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.