All MIBs › WLSX-TRAP-MIB
Organization: Aruba Wireless Networks
Last Updated: 2012-12-15
Description: MIB for Aruba wireless LAN controllers and switches, defining traps for AP events, client authentication, ARM channel changes, VRRP state transitions, and stack topology changes
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is WLSX-TRAP-MIB?
WLSX-TRAP-MIB is Aruba Networks' MIB defining the SNMP trap notifications emitted by its wireless LAN controllers and switches, covering a broad range of operational events across the wireless infrastructure. It defines traps for access point connect/disconnect events, wireless client authentication successes and failures, Adaptive Radio Management (ARM) channel/power changes, VRRP redundancy state transitions, and switch stack topology changes. Its monitoring value is centered on real-time fault and state-change detection rather than polled counters: an operator relies on these traps to be alerted immediately when an AP goes down, a client fails to authenticate repeatedly (a potential security issue), a controller's redundancy state fails over (a high-availability/fault event), or the switch stack topology changes (a hardware/cabling fault), all of which reflect the health of the wireless controller hardware and its managed APs. It is Aruba-proprietary but its VRRP-related traps correlate with the standard VRRP MIB's state model. It is deployed on Aruba wireless LAN controllers and switch stacks in enterprise and campus wireless network deployments. Network engineers evaluating or troubleshooting this functionality can download the WLSX-TRAP-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in WLSX-TRAP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Aruba wireless LAN controllers
- Aruba switches (stacked)
Monitoring Examples
This module defines only trap/notification types with no sample runtime objects listed, so no specific pollable object names can be cited. In practice a network management station would register as a trap receiver and alert on AP-down, client-authentication-failure, ARM channel-change, VRRP-failover, and stack-topology-change traps to catch AP outages, security issues, and controller redundancy failovers as they happen.
This MIB depends on
Related MIBs
Imported Objects
From ARUBA-MIB
| wlsrEnterpriseMibModules | OBJECT-IDENTITY |
From ARUBA-TC
| ArubaAPMasterStatus | |
| ArubaARMChangeReason | |
| ArubaAccessPointMode | |
| ArubaAddressType | |
| ArubaAuthenticationMethods | |
| ArubaBlackListReason | |
| ArubaConfigurationChangeType | |
| ArubaConfigurationState | |
| ArubaDBType | |
| ArubaEnableValue | |
| ArubaFrameType | |
| ArubaHTExtChannel | |
| ArubaIfState | |
| ArubaIfStateChangeReason | |
| ArubaOperStateValue | |
| ArubaStackChangeEvent | |
| ArubaStackIfTopoJoined | |
| ArubaStackState | |
| ArubaStationType | |
| ArubaSwitchRole | |
| ArubaThresholdResourceType | |
| ArubaVrrpState |
From SNMPv2-CONF
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| TEXTUAL-CONVENTION | |
| snmpModules |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| MacAddress | |
| PhysAddress | |
| RowStatus | |
| StorageType | |
| TAddress | |
| TDomain | |
| TestAndIncr | |
| TimeInterval | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| wlsrTrapMIB | 1.3.6.1.4.1.14823.2.3.1.11 | This MIB defines the Traps generated by the switch. | ||
| wlsxTrapsGroup | 1.3.6.1.4.1.14823.2.3.1.11.1 | |||
| wlsxTrapObjectsGroup | 1.3.6.1.4.1.14823.2.3.1.11.1.1 | |||
| MAC wlsxTrapAPMacAddress | 1.3.6.1.4.1.14823.2.3.1.11.1.1.1 | MacAddress | accessible-for-notify | This object is used in the traps to indicate the wired MAC address of an access point, for which the trap is being raised. |
| IP wlsxTrapAPIpAddress | 1.3.6.1.4.1.14823.2.3.1.11.1.1.2 | IpAddress | accessible-for-notify | This object is used in the traps to indicate the IP address of an access point, for which the trap is being raised. |
| MAC wlsxTrapAPBSSID | 1.3.6.1.4.1.14823.2.3.1.11.1.1.3 | MacAddress | accessible-for-notify | This object is used in the traps to indicate the BSSID of the access point, for which the trap is being raised. |
| STR wlsxTrapEssid | 1.3.6.1.4.1.14823.2.3.1.11.1.1.4 | DisplayString | accessible-for-notify | This object is used in the traps to indicate the SSID of the access point, for which the trap is being raised. |
| MAC wlsxTrapTargetAPBSSID | 1.3.6.1.4.1.14823.2.3.1.11.1.1.5 | MacAddress | accessible-for-notify | This object is used in the traps to indicate the BSSID of the access point, for which we are raising the trap. If an Air Monitor is sending the trap then this will indicate AP. If an access point is sending the trap, then it will point to itself. |
| STR wlsxTrapTargetAPSSID | 1.3.6.1.4.1.14823.2.3.1.11.1.1.6 | DisplayString | accessible-for-notify | This object is used in the traps to indicate the SSID of the access point, for which the trap is being raised. If an Air Monitor is sending the trap then this will indicate AP. If an access point is sending the trap, then it will point to itself. |
| I32 wlsxTrapTargetAPChannel | 1.3.6.1.4.1.14823.2.3.1.11.1.1.7 | Integer32 | accessible-for-notify | This object is used in the traps to indicate the channel of the access point, for which the trap is being raised. If an air monitor is sending the trap then this will indicate AP. If an access point is sending the trap, then it will point to itself. |
| MAC wlsxTrapNodeMac | 1.3.6.1.4.1.14823.2.3.1.11.1.1.8 | MacAddress | accessible-for-notify | This object is used in the traps to indicate the MAC address of a node. |
| MAC wlsxTrapSourceMac | 1.3.6.1.4.1.14823.2.3.1.11.1.1.9 | MacAddress | accessible-for-notify | This object is used in the traps to indicate the MAC address of the source. |
| MAC wlsxReceiverMac | 1.3.6.1.4.1.14823.2.3.1.11.1.1.10 | MacAddress | accessible-for-notify | This object is used in the traps to indicate the MAC address of the receiver. |
| MAC wlsxTrapTransmitterMac | 1.3.6.1.4.1.14823.2.3.1.11.1.1.11 | MacAddress | accessible-for-notify | This object is used in the traps to indicate the MAC address of the transmitter. |
| MAC wlsxTrapReceiverMac | 1.3.6.1.4.1.14823.2.3.1.11.1.1.12 | MacAddress | accessible-for-notify | This object is used in the traps to indicate the MAC address of the receiver. |
| I32 wlsxTrapSnr | 1.3.6.1.4.1.14823.2.3.1.11.1.1.13 | Integer32 | accessible-for-notify | This object is used in the traps to indicate the Signal to Noise ratio. |
| STR wlsxTrapSignatureName | 1.3.6.1.4.1.14823.2.3.1.11.1.1.14 | DisplayString | accessible-for-notify | This object is used in the traps to indicate the Signature Name. |
| ARU wlsxTrapFrameType | 1.3.6.1.4.1.14823.2.3.1.11.1.1.15 | ArubaFrameType | accessible-for-notify | This object is used in the traps to indicate the Frame Type |
| ADR wlsxTrapAddressType | 1.3.6.1.4.1.14823.2.3.1.11.1.1.16 | ArubaAddressType | accessible-for-notify | This object is used in the traps to indicate the Address type. |
| STR wlsxTrapAPLocation | 1.3.6.1.4.1.14823.2.3.1.11.1.1.17 | DisplayString | accessible-for-notify | This object is used in the traps to indicate the Location of the AP. |
| I32 wlsxTrapAPChannel | 1.3.6.1.4.1.14823.2.3.1.11.1.1.18 | Integer32 | accessible-for-notify | This object is used in the traps to indicate the Current Channel. |
| I32 wlsxTrapAPTxPower | 1.3.6.1.4.1.14823.2.3.1.11.1.1.19 | Integer32 | accessible-for-notify | This object is used in the traps to indicate the AP Transmit Power. |
| MAC wlsxTrapMatchedMac | 1.3.6.1.4.1.14823.2.3.1.11.1.1.20 | MacAddress | accessible-for-notify | This object is used in the traps to indicate the MAC address |
| IP wlsxTrapMatchedIp | 1.3.6.1.4.1.14823.2.3.1.11.1.1.21 | IpAddress | accessible-for-notify | This object is used in the traps to indicate the IP address |
| STR wlsxTrapRogueIfoURL | 1.3.6.1.4.1.14823.2.3.1.11.1.1.22 | DisplayString | accessible-for-notify | This object is used to point to the WEBUI Rogue AP information URL. |
| I32 wlsxTrapVlanId | 1.3.6.1.4.1.14823.2.3.1.11.1.1.23 | Integer32 | accessible-for-notify | This object is used in the traps to indicate the VLAN Id. |
| ARU wlsxTrapAdminStatus | 1.3.6.1.4.1.14823.2.3.1.11.1.1.24 | ArubaEnableValue | accessible-for-notify | This object is used in the traps to indicate the admin status of VLAN. |
| ARU wlsxTrapOperStatus | 1.3.6.1.4.1.14823.2.3.1.11.1.1.25 | ArubaOperStateValue | accessible-for-notify | This object is used in the traps to indicate the admin status of VLAN. |
| STR wlsxTrapAuthServerName | 1.3.6.1.4.1.14823.2.3.1.11.1.1.26 | DisplayString | accessible-for-notify | This object is used in the traps to indicate the Authentication Server used for Authentication. |
| I32 wlsxTrapAuthServerTimeout | 1.3.6.1.4.1.14823.2.3.1.11.1.1.27 | Integer32 | accessible-for-notify | This object is used in the traps to indicate the Authentication Server Timeout. |
| I32 wlsxTrapCardSlot | 1.3.6.1.4.1.14823.2.3.1.11.1.1.28 | Integer32 | accessible-for-notify | This object is used in the traps to indicate the Slot in which this card is present. |
| STR wlsxTrapTemperatureValue | 1.3.6.1.4.1.14823.2.3.1.11.1.1.29 | DisplayString | accessible-for-notify | This object is used in the traps to indicate the Temperature Value. |
| STR wlsxTrapProcessName | 1.3.6.1.4.1.14823.2.3.1.11.1.1.30 | DisplayString | accessible-for-notify | This object is used in the traps to indicate the Process name. |
| I32 wlsxTrapFanNumber | 1.3.6.1.4.1.14823.2.3.1.11.1.1.31 | Integer32 | accessible-for-notify | This object is used in the traps to indicate the Fan Number. |
| STR wlsxTrapVoltageType | 1.3.6.1.4.1.14823.2.3.1.11.1.1.32 | DisplayString | accessible-for-notify | This object is used in the traps to indicate the type of Voltage. |
| STR wlsxTrapVoltageValue | 1.3.6.1.4.1.14823.2.3.1.11.1.1.33 | DisplayString | accessible-for-notify | This object is used in the traps to indicate the voltage value in Float. |
| ARU wlsxTrapStationBlackListReason | 1.3.6.1.4.1.14823.2.3.1.11.1.1.34 | ArubaBlackListReason | accessible-for-notify | The Reason for which a station is black listed. |
| IP wlsxTrapSpoofedIpAddress | 1.3.6.1.4.1.14823.2.3.1.11.1.1.35 | IpAddress | accessible-for-notify | This object is used in a trap to identify a spoofed IP address. |
| MAC wlsxTrapSpoofedOldPhyAddress | 1.3.6.1.4.1.14823.2.3.1.11.1.1.36 | MacAddress | accessible-for-notify | This object is used in a trap to identify an old MAC address. |
| MAC wlsxTrapSpoofedNewPhyAddress | 1.3.6.1.4.1.14823.2.3.1.11.1.1.37 | MacAddress | accessible-for-notify | This object is used in a trap to identify a New MAC address. |
| STR wlsxTrapDBName | 1.3.6.1.4.1.14823.2.3.1.11.1.1.38 | DisplayString | accessible-for-notify | This object is used in a trap to identify name of the database. |
| STR wlsxTrapDBUserName | 1.3.6.1.4.1.14823.2.3.1.11.1.1.39 | DisplayString | accessible-for-notify | This object is used in a trap to identify name of the database user. |
| STR wlsxTrapDBIpAddress | 1.3.6.1.4.1.14823.2.3.1.11.1.1.40 | DisplayString | accessible-for-notify | This object is used in a trap to identify the IpAddress of the Database. |
| ARU wlsxTrapDBType | 1.3.6.1.4.1.14823.2.3.1.11.1.1.41 | ArubaDBType | accessible-for-notify | This object is used in a trap to identify the port of the user. |
| I32 wlsxTrapVrrpID | 1.3.6.1.4.1.14823.2.3.1.11.1.1.42 | Integer32 | accessible-for-notify | This object contains the Virtual Router Identifier. |
| IP wlsxTrapVrrpMasterIp | 1.3.6.1.4.1.14823.2.3.1.11.1.1.43 | IpAddress | accessible-for-notify | This object contains the Master IP address. |
| ARU wlsxTrapVrrpOperState | 1.3.6.1.4.1.14823.2.3.1.11.1.1.44 | ArubaVrrpState | accessible-for-notify | This object represents the VRRP Operational state. |
| STR wlsxTrapESIServerGrpName | 1.3.6.1.4.1.14823.2.3.1.11.1.1.45 | DisplayString | accessible-for-notify | This object represents the External Services Interface (ESI) Server Group name |
| STR wlsxTrapESIServerName | 1.3.6.1.4.1.14823.2.3.1.11.1.1.46 | DisplayString | accessible-for-notify | This object represents the External Services Interface (ESI) Server Name |
| IP wlsxTrapESIServerIpAddress | 1.3.6.1.4.1.14823.2.3.1.11.1.1.47 | IpAddress | accessible-for-notify | This object represents the External Services Interface (ESI) Server IP address |
| I32 wlsxTrapLicenseDaysRemaining | 1.3.6.1.4.1.14823.2.3.1.11.1.1.48 | Integer32 | accessible-for-notify | This object represents number of the days remaining prior to a license expiry. |
| IP wlsxTrapSwitchIp | 1.3.6.1.4.1.14823.2.3.1.11.1.1.49 | IpAddress | accessible-for-notify | This object represents the controller IP address. |
| ARU wlsxTrapSwitchRole | 1.3.6.1.4.1.14823.2.3.1.11.1.1.50 | ArubaSwitchRole | accessible-for-notify | This object represents the Role of the controller. |
| IP wlsxTrapUserIpAddress | 1.3.6.1.4.1.14823.2.3.1.11.1.1.51 | IpAddress | accessible-for-notify | This object represents IP address of the User. |
| MAC wlsxTrapUserPhyAddress | 1.3.6.1.4.1.14823.2.3.1.11.1.1.52 | MacAddress | accessible-for-notify | This object represents MAC address of the User. |
| STR wlsxTrapUserName | 1.3.6.1.4.1.14823.2.3.1.11.1.1.53 | DisplayString | accessible-for-notify | This object represents the user name. |
| STR wlsxTrapUserRole | 1.3.6.1.4.1.14823.2.3.1.11.1.1.54 | DisplayString | accessible-for-notify | This object represents the Authentication method of the user. |
| ARU wlsxTrapUserAuthenticationMethod | 1.3.6.1.4.1.14823.2.3.1.11.1.1.55 | ArubaAuthenticationMethods | accessible-for-notify | This object represents the Authentication method of the user. |
| I32 wlsxTrapAPRadioNumber | 1.3.6.1.4.1.14823.2.3.1.11.1.1.56 | Integer32 | accessible-for-notify | This object represents the radio number. |
| STR wlsxTrapRogueInfoURL | 1.3.6.1.4.1.14823.2.3.1.11.1.1.57 | DisplayString | accessible-for-notify | This object is used to point to the WEBGUI Rogue AP information URL. |
| STR wlsxTrapInterferingAPInfoURL | 1.3.6.1.4.1.14823.2.3.1.11.1.1.58 | DisplayString | accessible-for-notify | This object is used to point to the WEBGUI Rogue interfering AP information URL. |
| I32 wlsxTrapPortNumber | 1.3.6.1.4.1.14823.2.3.1.11.1.1.59 | Integer32 | accessible-for-notify | This object is used in the traps to indicate the port number. |
| DAT wlsxTrapTime | 1.3.6.1.4.1.14823.2.3.1.11.1.1.60 | DateAndTime | accessible-for-notify | This object is used in all the enterprise traps to indicate the the time when the trap is generated on the controller. |
| IP wlsxTrapHostIp | 1.3.6.1.4.1.14823.2.3.1.11.1.1.61 | IpAddress | accessible-for-notify | This object represents the Trap host. |
| I32 wlsxTrapHostPort | 1.3.6.1.4.1.14823.2.3.1.11.1.1.62 | Integer32 | accessible-for-notify | This object represents the Trap host port. |
| I32 wlsxTrapConfigurationId | 1.3.6.1.4.1.14823.2.3.1.11.1.1.63 | Integer32 | accessible-for-notify | This object represents the ID of the configuration, to be used in traps. |
| STR wlsxTrapCTSURL | 1.3.6.1.4.1.14823.2.3.1.11.1.1.64 | DisplayString | accessible-for-notify | This object represents the URL from which the transfer should happen. |
| STR wlsxTrapCTSTransferType | 1.3.6.1.4.1.14823.2.3.1.11.1.1.65 | DisplayString | accessible-for-notify | This object represents the transfer type, upload or download. |
| ARU wlsxTrapConfigurationState | 1.3.6.1.4.1.14823.2.3.1.11.1.1.66 | ArubaConfigurationState | accessible-for-notify | This object represents state of the configuration transfer. |
| STR wlsxTrapUpdateFailureReason | 1.3.6.1.4.1.14823.2.3.1.11.1.1.67 | DisplayString | accessible-for-notify | This object represents the reason for the update failure. |
| STR wlsxTrapUpdateFailedObj | 1.3.6.1.4.1.14823.2.3.1.11.1.1.68 | DisplayString | accessible-for-notify | This variable represents the AMAPI object which is the reason for the the update failure. |
| ARU wlsxTrapTableEntryChangeType | 1.3.6.1.4.1.14823.2.3.1.11.1.1.69 | ArubaConfigurationChangeType | accessible-for-notify | This object represents type of the configuration change. |
| STR wlsxTrapGlobalConfigObj | 1.3.6.1.4.1.14823.2.3.1.11.1.1.70 | DisplayString | accessible-for-notify | This variable represents the AMAPI object corresponding to the global configuration change. |
| I32 wlsxTrapTableGenNumber | 1.3.6.1.4.1.14823.2.3.1.11.1.1.71 | Integer32 | accessible-for-notify | This object represents generation number of a table. Used in the MMS, to keep track of the table content changes. |
| I32 wlsxTrapLicenseId | 1.3.6.1.4.1.14823.2.3.1.11.1.1.72 | Integer32 | accessible-for-notify | This object is used in the traps to indicate the license ID. |
| I32 wlsxTrapConfidenceLevel | 1.3.6.1.4.1.14823.2.3.1.11.1.1.73 | Integer32 | accessible-for-notify | This object is used in the traps to indicate the Confidence Level as a percentage |
| STR wlsxTrapMissingLicenses | 1.3.6.1.4.1.14823.2.3.1.11.1.1.74 | DisplayString | accessible-for-notify | This variable indicates any licenses that are not present during a configuration update |
| I32 wlsxVoiceCurrentNumCdr | 1.3.6.1.4.1.14823.2.3.1.11.1.1.75 | Integer32 | accessible-for-notify | This object represents the number of CDRs in buffer. |
| I32 wlsxTrapTunnelId | 1.3.6.1.4.1.14823.2.3.1.11.1.1.76 | Integer32 | accessible-for-notify | This Object represents the tunnel ID. |
| I32 wlsxTrapTunnelStatus | 1.3.6.1.4.1.14823.2.3.1.11.1.1.77 | Integer32 | accessible-for-notify | This Object represents the tunnel Status. |
| STR wlsxTrapTunnelUpReason | 1.3.6.1.4.1.14823.2.3.1.11.1.1.78 | DisplayString | accessible-for-notify | This Object represents the tunnel up reason. |
| STR wlsxTrapTunnelDownReason | 1.3.6.1.4.1.14823.2.3.1.11.1.1.79 | DisplayString | accessible-for-notify | This Object represents the tunnel down reason. |
| STR wlsxTrapApSerialNumber | 1.3.6.1.4.1.14823.2.3.1.11.1.1.80 | DisplayString | accessible-for-notify | This object represents the AP Serial Number. |
| STR wlsxTrapTimeStr | 1.3.6.1.4.1.14823.2.3.1.11.1.1.81 | DisplayString | accessible-for-notify | This object represents the Time in String format. |
| IP wlsxTrapMasterIp | 1.3.6.1.4.1.14823.2.3.1.11.1.1.82 | IpAddress | accessible-for-notify | This object represents the master IP address. |
| IP wlsxTrapLocalIp | 1.3.6.1.4.1.14823.2.3.1.11.1.1.83 | IpAddress | accessible-for-notify | This object represents the Local IP address. |
| STR wlsxTrapMasterName | 1.3.6.1.4.1.14823.2.3.1.11.1.1.84 | DisplayString | accessible-for-notify | This object represents the master controller name. |
| STR wlsxTrapLocalName | 1.3.6.1.4.1.14823.2.3.1.11.1.1.85 | DisplayString | accessible-for-notify | This object represents the local controller name. |
| IP wlsxTrapPrimaryControllerIp | 1.3.6.1.4.1.14823.2.3.1.11.1.1.86 | IpAddress | accessible-for-notify | This object represents the IP address of the AP's primary controller. |
| IP wlsxTrapBackupControllerIp | 1.3.6.1.4.1.14823.2.3.1.11.1.1.87 | IpAddress | accessible-for-notify | This object represents the IP address of the AP's backup controller. |
| STR wlsxTrapSpoofedFrameType | 1.3.6.1.4.1.14823.2.3.1.11.1.1.88 | DisplayString | accessible-for-notify | This object is used in the traps to indicate the Spoofed Frame Type |
| STR wlsxTrapAssociationType | 1.3.6.1.4.1.14823.2.3.1.11.1.1.89 | DisplayString | accessible-for-notify | This object is used in the traps to indicate the type of association |
| IP wlsxTrapDeviceIpAddress | 1.3.6.1.4.1.14823.2.3.1.11.1.1.90 | IpAddress | accessible-for-notify | This object represents the IP address of a device seen by an AP. |
| MAC wlsxTrapDeviceMac | 1.3.6.1.4.1.14823.2.3.1.11.1.1.91 | MacAddress | accessible-for-notify | This object represents the MAC address of a device seen by an AP. |
| IP wlsxTrapVcIpAddress | 1.3.6.1.4.1.14823.2.3.1.11.1.1.92 | IpAddress | accessible-for-notify | This object represents the Ip Address of a Voice client. |
| MAC wlsxTrapVcMacAddress | 1.3.6.1.4.1.14823.2.3.1.11.1.1.93 | MacAddress | accessible-for-notify | This object represents the MAC address of a Voice client. |
| STR wlsxTrapAPName | 1.3.6.1.4.1.14823.2.3.1.11.1.1.94 | DisplayString | accessible-for-notify | This object is used in the traps to indicate the Name of the AP. |
| I32 wlsxTrapApMode | 1.3.6.1.4.1.14823.2.3.1.11.1.1.95 | Integer32 | accessible-for-notify | This Object represents the AP Mode. |
| I32 wlsxTrapAPPrevChannel | 1.3.6.1.4.1.14823.2.3.1.11.1.1.96 | Integer32 | accessible-for-notify | This object is used in the traps to indicate the Previous Channel. |
| STR wlsxTrapAPPrevChannelSec | 1.3.6.1.4.1.14823.2.3.1.11.1.1.97 | ArubaHTExtChannel | accessible-for-notify | This object is used in the traps to indicate the Previous Secondary Channel. |
| I32 wlsxTrapAPPrevTxPower | 1.3.6.1.4.1.14823.2.3.1.11.1.1.98 | Integer32 | accessible-for-notify | This object is used in the traps to indicate previous AP Transmit Power. |
| NUM wlsxTrapAPCurMode | 1.3.6.1.4.1.14823.2.3.1.11.1.1.99 | ArubaAccessPointMode | accessible-for-notify | This Object represents the APs Current Mode. |
| NUM wlsxTrapAPPrevMode | 1.3.6.1.4.1.14823.2.3.1.11.1.1.100 | ArubaAccessPointMode | accessible-for-notify | This Object represents the APs Previous Mode. |
| ARU wlsxTrapAPARMChangeReason | 1.3.6.1.4.1.14823.2.3.1.11.1.1.101 | ArubaARMChangeReason | accessible-for-notify | This Object represents the APs Previous Mode. |
| STR wlsxTrapAPChannelSec | 1.3.6.1.4.1.14823.2.3.1.11.1.1.102 | ArubaHTExtChannel | accessible-for-notify | This object is used in the traps to indicate the Current Secondary Channel. |
| ARU wlsxTrapUserAttributeChangeType | 1.3.6.1.4.1.14823.2.3.1.11.1.1.103 | ArubaConfigurationChangeType | accessible-for-notify | This object represents type of the configuration change. |
| IP wlsxTrapApControllerIp | 1.3.6.1.4.1.14823.2.3.1.11.1.1.104 | IpAddress | accessible-for-notify | IP address of the controller to which the AP is (or was most recently) registered. |
| ARU wlsxTrapApMasterStatus | 1.3.6.1.4.1.14823.2.3.1.11.1.1.105 | ArubaAPMasterStatus | accessible-for-notify | Status of the AP as seen by the master when the status changes. |
| STR wlsxTrapCaName | 1.3.6.1.4.1.14823.2.3.1.11.1.1.106 | DisplayString | accessible-for-notify | This object is used in the traps to indicate the name of the trustpoint. |
| STR wlsxTrapCrlName | 1.3.6.1.4.1.14823.2.3.1.11.1.1.107 | DisplayString | accessible-for-notify | This object is used in the traps to indicate the name of the crl. |
| I32 wlsxTrapCount | 1.3.6.1.4.1.14823.2.3.1.11.1.1.108 | Integer32 | accessible-for-notify | This object represents the number of occurrence of this trap. |
| I32 wlsxTrapPowerSupplyNumber | 1.3.6.1.4.1.14823.2.3.1.11.1.1.109 | Integer32 | accessible-for-notify | This object represents the power supply number. |
| I32 wlsxTrapFanTrayNumber | 1.3.6.1.4.1.14823.2.3.1.11.1.1.110 | Integer32 | accessible-for-notify | This object represents the Fan Tray number. |
| ARU wlsxTrapClientClassification | 1.3.6.1.4.1.14823.2.3.1.11.1.1.111 | ArubaStationType | accessible-for-notify | This object is used in the traps to indicate the classification of the client. |
| ARU wlsxThresholdResourceType | 1.3.6.1.4.1.14823.2.3.1.11.1.1.112 | ArubaThresholdResourceType | accessible-for-notify | This object represents the Threshold alert's Resource Type . |
| STR wlsxThresholdResourceName | 1.3.6.1.4.1.14823.2.3.1.11.1.1.113 | DisplayString | accessible-for-notify | This object represents the Threshold alert's Resource Name . |
| I32 wlsxThresholdValue | 1.3.6.1.4.1.14823.2.3.1.11.1.1.114 | Integer32 | accessible-for-notify | This object represents the Threshold alert's set threshold value. |
| I32 wlsxResourceValue | 1.3.6.1.4.1.14823.2.3.1.11.1.1.115 | Integer32 | accessible-for-notify | This object represents the Threshold alert's actual value. |
| I32 wlsxStackPrevSlot | 1.3.6.1.4.1.14823.2.3.1.11.1.1.116 | Integer32 | accessible-for-notify | This object specifies the slot number of this stack element prior to topology change in stack. A value of -1 indicates that this slot was not in Active state of stack prior to topology change. |
| I32 wlsxStackCurrentSlot | 1.3.6.1.4.1.14823.2.3.1.11.1.1.117 | Integer32 | accessible-for-notify | This object specifies the slot number of this stack element after the topology change in stack. A value of -1 indicates that this slot is not in Active state of stack after the topology change. |
| ARU wlsxStackPrevState | 1.3.6.1.4.1.14823.2.3.1.11.1.1.118 | ArubaStackState | accessible-for-notify | This object specifies the state of this stack element prior to topology change in stack. |
| ARU wlsxStackCurrentState | 1.3.6.1.4.1.14823.2.3.1.11.1.1.119 | ArubaStackState | accessible-for-notify | This object specifies the state of this stack element after topology change in stack. |
| ARU wlsxStackChangeEvent | 1.3.6.1.4.1.14823.2.3.1.11.1.1.120 | ArubaStackChangeEvent | accessible-for-notify | This object specifies the event which caused change in topology in stack. |
| ARU wlsxStackProtoIfTopoJoined | 1.3.6.1.4.1.14823.2.3.1.11.1.1.121 | ArubaStackIfTopoJoined | accessible-for-notify | This object specifies whether an interface has joined the stacking topology or left the topology. |
| MAC wlsxStackMemberMacAddress | 1.3.6.1.4.1.14823.2.3.1.11.1.1.122 | MacAddress | accessible-for-notify | This object specifies mac-address of this stack element. |
| I32 wlsxStackMemberSlotNumber | 1.3.6.1.4.1.14823.2.3.1.11.1.1.123 | Integer32 | accessible-for-notify | This object specifies the slot number of this element in stack. |
| STR wlsxStackIfName | 1.3.6.1.4.1.14823.2.3.1.11.1.1.124 | DisplayString | accessible-for-notify | This object specifies the interface name which is part of stacking link connected to other stacking element. |
| I32 wlsxTrapLicenseServerDaysRemaining | 1.3.6.1.4.1.14823.2.3.1.11.1.1.125 | Integer32 | accessible-for-notify | This object represents number of the days remaining prior to expiry of license limits sent by the server. |
| I32 wlsxTrapLicenseClientDaysRemaining | 1.3.6.1.4.1.14823.2.3.1.11.1.1.126 | Integer32 | accessible-for-notify | This object represents number of the days remaining prior to expiry of licenses contributed by a license client. |
| I32 wlsxIfIndex | 1.3.6.1.4.1.14823.2.3.1.11.1.1.127 | Integer32 | accessible-for-notify | This object specifies the ifIndex. |
| ARU wlsxIfState | 1.3.6.1.4.1.14823.2.3.1.11.1.1.128 | ArubaIfState | accessible-for-notify | This object specifies the state of an interface. |
| ARU wlsxIfStateChangeReason | 1.3.6.1.4.1.14823.2.3.1.11.1.1.129 | ArubaIfStateChangeReason | accessible-for-notify | This object specifies the reason for interface state change. |
| wlsxTrapDefinitionsGroup | 1.3.6.1.4.1.14823.2.3.1.11.1.2 | |||
| NTF wlsxVlanLinkUp | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1000 | This trap indicates that a VLAN interface is up. | ||
| NTF wlsxVlanLinkDown | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1001 | This trap indicates that a VLAN interface is down. | ||
| NTF wlsxSignatureMatch | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1002 | This trap indicates that a signature match was detected. | ||
| NTF wlsxNodeRateAnomaly | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1003 | This trap indicates that a node is exceeding the threshold set for the frame type. | ||
| NTF wlsxNormalTemperature | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1004 | This trap indicates that the Temperature has returned to an acceptable range. | ||
| NTF wlsxProcessRestart | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1005 | This trap indicates that the named process has been restarted. | ||
| NTF wlsxFlashSpaceOK | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1006 | This trap which indicates that the system flash space is back to a sufficient level. | ||
| NTF wlsxMemoryUsageOK | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1007 | This trap which indicates that the free memory usage is back to a sufficient level. | ||
| NTF wlsxPowerSupplyOK | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1008 | This trap indicates that the system power supply condition have returned to normal operation status. | ||
| NTF wlsxFanOK | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1009 | This trap indicates that the fan has returned to normal. | ||
| NTF wlsxInRangeVoltage | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1010 | This trap indicates that the controller Voltage is back within range. | ||
| NTF wlsxCoverageHoleResolved | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1011 | This trap indicates that a coverage hole at location wlsxTrapAPLocation has been resolved. | ||
| NTF wlsxNSwitchIPChanged | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1012 | This trap indicates that the controller IP address has changed. | ||
| NTF wlsxNSwitchRoleChange | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1013 | This trap indicates that the role of the controller IP address has changed. | ||
| NTF wlsxNUserEntryCreated | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1014 | This trap indicates that a new user was created. | ||
| NTF wlsxNUserEntryDeleted | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1015 | This trap indicates that a user was deleted. | ||
| NTF wlsxNUserEntryAuthenticated | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1016 | This trap indicates that a user is Authenticated. | ||
| NTF wlsxNUserEntryDeAuthenticated | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1017 | This trap indicates that a user is Deauthenticated. | ||
| NTF wlsxNUserAuthenticationFailed | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1018 | This trap indicates that a user authentication has failed. | ||
| NTF wlsxNAuthServerReqTimedOut | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1019 | This trap indicates that the authentication server request timed out. | ||
| NTF wlsxNAuthServerTimedOut | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1020 | This trap indicates that the authentication server timed out. | ||
| NTF wlsxNAuthServerIsUp | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1021 | This trap indicates that an authentication server is up. | ||
| NTF wlsxNAuthMaxUserEntries | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1022 | A trap which indicates that the user entries table is full and cannot add any more entries. | ||
| NTF wlsxNAuthMaxAclEntries | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1023 | A trap which indicates that the ACL Entries table is full and cannot add any more entries. | ||
| NTF wlsxNAuthMaxBWContracts | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1024 | A trap which indicates that the controller reached the maximum number of configurable Bandwidth contracts. | ||
| NTF wlsxNPowerSupplyFailure | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1025 | A trap which indicates that the power supply has failed. | ||
| NTF wlsxNFanFailure | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1026 | A trap which indicates that the fan has failed or is missing. | ||
| NTF wlsxNOutOfRangeVoltage | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1027 | A trap which indicates that the controller voltage is out of range. | ||
| NTF wlsxNOutOfRangeTemperature | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1028 | A trap which indicates that the controller internal temperature is out of range. | ||
| NTF wlsxNLCInserted | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1029 | A Trap which indicates that a line card is inserted. | ||
| NTF wlsxNSCInserted | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1030 | a Trap which indicates that a supervisor card is inserted. | ||
| NTF wlsxNGBICInserted | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1031 | A Trap which indicates that a GBIC is inserted in a Line Card. | ||
| NTF wlsxNProcessDied | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1032 | A Trap which indicates that a process has died. | ||
| NTF wlsxNProcessExceedsMemoryLimits | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1033 | A Trap which indicates that a process is consuming Large amounts of memory. | ||
| NTF wlsxNLowOnFlashSpace | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1034 | A Trap which indicates that the controller is running low on flash space. | ||
| NTF wlsxNLowMemory | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1035 | A Trap which indicates that the system free memory is low. | ||
| NTF wlsxNFanTrayRemoved | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1036 | A Trap which indicates that a fan tray is removed. | ||
| NTF wlsxNFanTrayInserted | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1037 | A Trap which indicates that a fan tray is inserted. | ||
| NTF wlsxNLCRemoved | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1038 | A Trap which indicates that a Line card is removed. | ||
| NTF wlsxNPowerSupplyMissing | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1039 | A Trap which indicates that the power supply is missing. | ||
| NTF wlsxNAccessPointIsUp | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1040 | A Trap which indicates that an access point up. | ||
| NTF wlsxNAccessPointIsDown | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1041 | A Trap which indicates that an access point down. | ||
| NTF wlsxNCoverageHoleDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1042 | This trap indicates that an access point at Location wlsxTrapAPLocation has detected a Coverage Hole. | ||
| NTF wlsxNChannelChanged | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1043 | This trap indicates that an access point at Location wlsxTrapAPLocation has changed the channel. | ||
| NTF wlsxNStationAddedToBlackList | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1044 | This trap indicates that the station is black listed. | ||
| NTF wlsxNStationRemovedFromBlackList | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1045 | This trap indicates that the station is removed from the black list. | ||
| NTF wlsxNIpSpoofingDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1046 | A trap indicating that the controller detected IP Spoofing. | ||
| NTF wlsxNDBCommunicationFailure | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1047 | This trap indicates that communication with Database failed. | ||
| NTF wlsxNVrrpStateChange | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1048 | This trap indicates that VRRP state has changed on the controller. | ||
| NTF wlsxNRadioAttributesChanged | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1049 | A Trap which indicates changes in the Radio attributes of an access point. | ||
| NTF wlsxNESIServerUp | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1050 | A Trap which indicates that a ESI server is up. | ||
| NTF wlsxNESIServerDown | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1051 | A Trap which indicates that a ESI server is down. | ||
| NTF wlsxNLicenseExpiry | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1052 | A Trap which indicates that one or more licenses on the controller will expire in wlsxTrapLicenseDaysRemaining days. | ||
| NTF wlsxUnsecureAPDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1053 | This trap indicates that an unauthorized access point is connected to the wired network. The access point is declared Rogue because it was matched to a MAC address. | ||
| NTF wlsxUnsecureAPResolved | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1054 | This trap indicates that a previously detected access point, classified as Rogue, is no longer present in the network. | ||
| NTF wlsxStaImpersonation | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1055 | This trap indicates that an AM detected Station Impersonation. | ||
| NTF wlsxReservedChannelViolation | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1056 | This trap indicates that an AM detected an access point which is violating the Reserved Channel configuration. | ||
| NTF wlsxValidSSIDViolation | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1057 | This trap indicates that an AP has detected an access point is violating Valid SSID configuration by using an SSID that is reserved for use by a valid AP only. | ||
| NTF wlsxChannelMisconfiguration | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1058 | This trap indicates that an AP detected an access point that has a channel misconfiguration because it is using a channel that is not valid. | ||
| NTF wlsxOUIMisconfiguration | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1059 | This trap indicates that an AP detected an access point that has an OUI misconfiguration because it is using an OUI that is not valid. | ||
| NTF wlsxSSIDMisconfiguration | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1060 | This trap indicates that an AP detected an access point that has an SSID misconfiguration because it is using an SSID that is not valid. | ||
| NTF wlsxShortPreableMisconfiguration | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1061 | This trap indicates that an access point has bad Short preamble configuration. | ||
| NTF wlsxWPAMisconfiguration | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1062 | This trap indicates that an AP detected an access point that is misconfigured because it is not using WPA. | ||
| NTF wlsxAdhocNetworkDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1063 | This trap indicates that an AM has detected an Ad hoc network. | ||
| NTF wlsxAdhocNetworkRemoved | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1064 | This trap indicates that a previously detected Ad hoc Network is no longer present in the network. | ||
| NTF wlsxStaPolicyViolation | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1065 | This trap indicates that Protection was enforced because a valid station's association to a non-valid access point violated Valid Station policy. For more info check: http://www.wve.org/entries/show/WVE-2005-0008 http://www.wve.org/entries/show/WVE-2005-0019 | ||
| NTF wlsxRepeatWEPIVViolation | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1066 | This trap indicates that an AP detected that a valid access point is using the same WEP initialization vector in consecutive packets. | ||
| NTF wlsxWeakWEPIVViolation | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1067 | This trap indicates that an AP detected that a valid access point is using a Weak WEP initialization vector. For more info check: http://www.wve.org/entries/show/WVE-2005-0021 | ||
| NTF wlsxChannelInterferenceDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1068 | This trap indicates that an AP has detected channel interference. | ||
| NTF wlsxChannelInterferenceCleared | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1069 | This trap indicates that a previously detected channel interference is no longer present. | ||
| NTF wlsxAPInterferenceDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1070 | This trap indicates that an AP has detected interference for an access point. | ||
| NTF wlsxAPInterferenceCleared | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1071 | This trap indicates that the previously detected interference for an access point is no longer present. | ||
| NTF wlsxStaInterferenceDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1072 | This trap indicates that an AP has detected interference for a station. | ||
| NTF wlsxStaInterferenceCleared | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1073 | This trap indicates that the previously detected interference for a station is no longer present. | ||
| NTF wlsxFrameRetryRateExceeded | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1074 | This trap indicates that an AP detected that an access point has exceeded the configured upper threshold for Frame Retry Rate. | ||
| NTF wlsxFrameReceiveErrorRateExceeded | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1075 | This trap indicates that an AP detected that an access point has exceeded the configured upper threshold for Frame Receive Error Rate. | ||
| NTF wlsxFrameFragmentationRateExceeded | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1076 | This trap indicates that an AP detected that an access point exceeded the configured upper threshold for Frame Fragmentation Rate. | ||
| NTF wlsxFrameBandWidthRateExceeded | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1077 | This trap indicates that an AP detected that a station or access point has exceeded the configured upper threshold for Bandwidth rate. | ||
| NTF wlsxFrameLowSpeedRateExceeded | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1078 | This trap indicates that an AP detected that a station has exceeded the configured upper threshold for Low speed rate. | ||
| NTF wlsxFrameNonUnicastRateExceeded | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1079 | This trap indicates that an AP detected that a station has exceeded the configured upper threshold for Non Unicast traffic rate. | ||
| NTF wlsxLoadbalancingEnabled | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1080 | This trap indicates that an AM is reporting that an AP has enabled Load balancing. | ||
| NTF wlsxLoadbalancingDisabled | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1081 | This trap indicates that an AM is reporting that an AP has enabled Load balancing. | ||
| NTF wlsxChannelFrameRetryRateExceeded | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1082 | This trap indicates that an AP has detected that the configured upper threshold for Frame Retry Rate was exceeded on a channel. | ||
| NTF wlsxChannelFrameFragmentationRateExceeded | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1083 | This trap indicates that an AP has detected that the configured upper threshold for Frame Fragmentation Rate was exceeded on a channel. | ||
| NTF wlsxChannelFrameErrorRateExceeded | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1084 | This trap indicates that an AP has detected that the configured upper threshold for Frame Receive Error Rate was exceeded on a channel. | ||
| NTF wlsxSignatureMatchAP | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1085 | This trap indicates that an AP detected a signature match in a frame from an access point. | ||
| NTF wlsxSignatureMatchSta | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1086 | This trap indicates that an AP detected a signature match in a frame from a Station. | ||
| NTF wlsxChannelRateAnomaly | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1087 | This trap indicates that an AP detected frames on a channel which exceed the configured IDS rate threshold. For more info check: http://www.wve.org/entries/show/WVE-2005-0052 http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0047 http://www.wve.org/entries/show/WVE-2005-0048 | ||
| NTF wlsxNodeRateAnomalyAP | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1088 | This trap indicates that an AP detected frames transmitted or received by an access point, which exceed the configured IDS rate threshold. For more info check: http://www.wve.org/entries/show/WVE-2005-0052 http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0047 http://www.wve.org/entries/show/WVE-2005-0048 | ||
| NTF wlsxNodeRateAnomalySta | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1089 | This trap indicates that an AP detected frames transmitted or received by a node, which exceed the configured IDS rate threshold. | ||
| NTF wlsxEAPRateAnomaly | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1090 | This trap indicates that the rate of EAP Handshake packets received by an AP has exceeded the configured IDS EAP Handshake rate threshold. For more info check: http://www.wve.org/entries/show/WVE-2005-0049 | ||
| NTF wlsxSignalAnomaly | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1091 | This trap indicates that an AM detected a Signal Anomaly. | ||
| NTF wlsxSequenceNumberAnomalyAP | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1092 | This trap indicates that an AM received packets from an AP which exceeds the acceptable sequence number difference. The acceptable sequence number difference is an IDS configuration object. For more info check: http://www.wve.org/entries/show/WVE-2005-0061 http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0008 http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0047 http://www.wve.org/entries/show/WVE-2005-0048 | ||
| NTF wlsxSequenceNumberAnomalySta | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1093 | This trap indicates that an AM received packets from a Node which exceeds the acceptable sequence number difference. The acceptable sequence number difference is an IDS configuration object. For more info check: http://www.wve.org/entries/show/WVE-2005-0061 http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0008 http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0047 http://www.wve.org/entries/show/WVE-2005-0048 | ||
| NTF wlsxDisconnectStationAttack | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1094 | This trap indicates that an AM detected a station Disconnect attack. For more info check: http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0048 | ||
| NTF wlsxApFloodAttack | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1095 | This trap indicates that the number of potential fake APs detected by an AP has exceeded the configured IDS threshold. This is the total number of fake APs observed across all bands. For more info check: http://www.wve.org/entries/show/WVE-2005-0056 | ||
| NTF wlsxAdhocNetwork | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1096 | This trap indicates that an AM detected an Ad hoc Network. An Station is connected to an ad hoc AP. | ||
| NTF wlsxWirelessBridge | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1097 | This trap indicates that an AP detected a Wireless Bridge when a WDS frame was seen between the transmitter and receiver addresses. | ||
| NTF wlsxInvalidMacOUIAP | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1098 | This trap indicates that an AP detected an invalid MAC OUI in the BSSID of a frame. An invalid MAC OUI suggests that the frame may be spoofed. | ||
| NTF wlsxInvalidMacOUISta | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1099 | This trap indicates that an AP detected an invalid MAC OUI in the SRC or DST address of a frame. An invalid MAC OUI suggests that the frame may be spoofed. | ||
| NTF wlsxWEPMisconfiguration | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1100 | This trap indicates that an AP detected an access point that is misconfigured because it does not have Privacy enabled. | ||
| NTF wlsxStaRepeatWEPIVViolation | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1101 | This trap indicates that an AP detected that a valid station is using the same WEP initialization vector in consecutive packets. | ||
| NTF wlsxStaWeakWEPIVViolation | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1102 | This trap indicates that an AP detected that a valid station is using a Weak WEP initialization vector. | ||
| NTF wlsxStaAssociatedToUnsecureAP | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1103 | This trap indicates that an AM detected a client associated with a Rogue access point. | ||
| NTF wlsxStaUnAssociatedFromUnsecureAP | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1104 | This trap indicates that a previously detected rogue access point association is no longer present. | ||
| NTF wlsxAdhocNetworkBridgeDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1105 | This trap indicates that an AM has detected an Ad hoc network that is bridging to a wired network | ||
| NTF wlsxInterferingApDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1106 | This trap indicates that an AP detected an access point classified as Interfering. The access point is declared Interfering because it is neither authorized or classified as Rogue. | ||
| NTF wlsxPortUp | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1107 | This trap indicates that a Physical port is up. | ||
| NTF wlsxPortDown | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1108 | This trap indicates that a Physical port is Down. | ||
| NTF wlsxBSSIDIsUp | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1109 | A Trap which indicates that an access point BSSID is up. | ||
| NTF wlsxBSSIDIsDown | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1110 | A Trap which indicates that an access point BSSID is down. | ||
| NTF wlsxColdStart | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1111 | An enterprise version of cold start trap, which contains the controller time stamp. | ||
| NTF wlsxWarmStart | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1112 | An enterprise version of warm start trap, which contains the controller time stamp. | ||
| NTF wlsxAPImpersonation | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1113 | This trap indicates that an AP detected AP Impersonation because the number of beacons seen has exceeded the expected number by the configured percentage threshold. The expected number is calculated based on the Beacon Interval Field in the Beacon frame. | ||
| NTF wlsxInformQueueOverFlow | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1114 | This trap indicates that an Inform queue overflow condition occurred. | ||
| NTF wlsxNAuthServerIsDown | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1115 | This trap indicates that an authentication server is down. | ||
| NTF wlsxCTSTransferError | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1116 | This trap indicates the status of the configuration transfer from the management station. | ||
| NTF wlsxCTSTransferSucceeded | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1117 | This trap indicates the status of the configuration transfer from the management station. | ||
| NTF wlsxConfigurationUpdateError | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1118 | This trap indicates the configuration update status. | ||
| NTF wlsxConfigurationUpdateSucceeded | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1119 | This trap indicates the configuration update status. | ||
| NTF wlsxGlobalConfigurationChangeNotification | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1120 | This trap indicates that global configuration was modified on the controller. | ||
| NTF wlsxUserEntryChanged | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1121 | This trap indicates that the user configuration has changed. | ||
| NTF wlsxAPBssidEntryChanged | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1122 | This trap indicates that the BSSID configuration has changed. | ||
| NTF wlsxAPRadioEntryChanged | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1123 | This trap indicates that the Radio configuration has changed. | ||
| NTF wlsxAPEntryChanged | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1124 | This trap indicates that the AP configuration has changed. | ||
| NTF wlsxSwitchListEntryChanged | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1125 | This trap indicates that the controller list has changed. | ||
| NTF wlsxPortEntryChanged | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1126 | This trap indicates that the port configuration has changed. | ||
| NTF wlsxVlanEntryChanged | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1127 | This trap indicates that the VLAN configuration has changed. | ||
| NTF wlsxVlanInterfaceEntryChanged | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1128 | This trap indicates that the VLAN Interface configuration has changed. | ||
| NTF wlsxWindowsBridgeDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1129 | This trap indicates that an AM has detected a station that is bridging from a wireless network to a wired network | ||
| NTF wlsxLicenseEntryChanged | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1130 | This trap indicates that the license table has changed. | ||
| NTF wlsxEsiServerChanged | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1131 | This trap indicates that the ESI server table has changed. | ||
| NTF wlsxMonAPEntryChanged | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1132 | This trap indicates that a monitored AP entry changed | ||
| NTF wlsxMonStationEntryChanged | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1133 | This trap indicates that a monitored station entry changed | ||
| NTF wlsxSignAPNetstumbler | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1134 | This trap indicates that an AP detected a signature match for Netstumbler from an access point. For more info check: http://www.wve.org/entries/show/WVE-2005-0025 | ||
| NTF wlsxSignStaNetstumbler | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1135 | This trap indicates that an AP detected a signature match for Netstumbler from a Station. For more info check: http://www.wve.org/entries/show/WVE-2005-0025 | ||
| NTF wlsxSignAPAsleap | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1136 | This trap indicates that an AP detected a signature match for ASLEAP from an access point. For more info check: http://www.wve.org/entries/show/WVE-2005-0027 | ||
| NTF wlsxSignStaAsleap | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1137 | This trap indicates that an AP detected a signature match for ASLEAP from a Station. For more info check: http://www.wve.org/entries/show/WVE-2005-0027 | ||
| NTF wlsxSignAPAirjack | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1138 | This trap indicates that an AP detected a signature match for AirJack from an access point. For more info check: http://www.wve.org/entries/show/WVE-2005-0018 | ||
| NTF wlsxSignStaAirjack | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1139 | This trap indicates that an AP detected a signature match for AirJack from a Station. For more info check: http://www.wve.org/entries/show/WVE-2005-0018 | ||
| NTF wlsxSignAPNullProbeResp | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1140 | This trap indicates that an AP detected a signature match for Null-Probe-Response from an access point. For more info check: http://www.wve.org/entries/show/WVE-2006-0064 | ||
| NTF wlsxSignStaNullProbeResp | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1141 | This trap indicates that an AP detected a signature match for Null-Probe-Response from a Station. For more info check: http://www.wve.org/entries/show/WVE-2006-0064 | ||
| NTF wlsxSignAPDeauthBcast | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1142 | This trap indicates that an AP detected a signature match for Deauth-Broadcast from an access point. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0045 | ||
| NTF wlsxSignStaDeauthBcast | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1143 | This trap indicates that an AP detected a signature match for Deauth-Broadcast from a Station. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0045 | ||
| NTF wlsxWindowsBridgeDetectedAP | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1144 | This trap indicates that an AP is detecting an access point that is bridging from a wireless network to a wired network. | ||
| NTF wlsxWindowsBridgeDetectedSta | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1145 | This trap indicates that an AP is detecting a station that is bridging from a wireless network to a wired network. | ||
| NTF wlsxAdhocNetworkBridgeDetectedAP | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1146 | This trap indicates that an AM has detected an Ad hoc network that is bridging to a wired network | ||
| NTF wlsxAdhocNetworkBridgeDetectedSta | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1147 | This trap indicates that an AM has detected an Ad hoc network that is bridging to a wired network | ||
| NTF wlsxDisconnectStationAttackAP | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1148 | This trap indicates that an AM detected a station disconnect attack. For more info check: http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0048 | ||
| NTF wlsxDisconnectStationAttackSta | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1149 | This trap indicates that an AM detected a station Disconnect attack. For more info check: http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0048 | ||
| NTF wlsxSuspectUnsecureAPDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1150 | This trap indicates that an access point, classified as Suspected Rogue, has been detected by a Controller. The AP is suspected to be rogue, with the supplied confidence level, because it was matched to the wired MAC address. | ||
| NTF wlsxSuspectUnsecureAPResolved | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1151 | This trap indicates that a previously detected access point, classified Suspected Rogue, is either no longer present in the network or has changed its state. | ||
| NTF wlsxConfigurationLicenseMismatch | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1152 | This trap indicates the configuration update status in the case where some configuration could not be applied due to missing licenses. | ||
| NTF wlsxVoiceCdrBufferThresholdReached | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1153 | This trap indicates that the CDR buffer threshold has been reached | ||
| NTF wlsxTunnelUp | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1154 | This trap indicates that a tunnel interface is up. | ||
| NTF wlsxTunnelDown | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1155 | This trap indicates that a tunnel interface is down. | ||
| NTF wlsxMeshNodeEntryChanged | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1156 | This trap indicates that the mesh node configuration has changed. | ||
| NTF wlsxHtGreenfieldSupported | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1157 | This trap indicates that an AP detected an access point that supports HT Greenfield mode. For more info check: http://www.wve.org/entries/show/WVE-2008-0005 | ||
| NTF wlsxHT40MHzIntoleranceAP | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1158 | This trap indicates that an AP is detecting an access point with the HT 40MHz intolerance setting. For more info check: http://www.wve.org/entries/show/WVE-2008-0004 | ||
| NTF wlsxHT40MHzIntoleranceSta | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1159 | This trap indicates that the system is detecting an HT 40MHz Intolerance setting from a Station. For more info check: http://www.wve.org/entries/show/WVE-2008-0004 | ||
| NTF wlsxNAuthServerAllInService | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1160 | This trap indicates that all authentication servers is a server group are brought back in service. | ||
| NTF wlsxNAdhocNetwork | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1161 | This trap indicates that an AP detected an ad hoc network where a station is connected to an ad hoc access point. | ||
| NTF wlsxNAdhocNetworkBridgeDetectedAP | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1162 | This trap indicates that an AP detected an ad hoc network that is bridging to a wired network. | ||
| NTF wlsxNAdhocNetworkBridgeDetectedSta | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1163 | This trap indicates that an AP detected an ad hoc network that is bridging to a wired network. | ||
| NTF wlsxNAuthMaxXsecUserEntries | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1164 | A trap which indicates that the xSec user limit is reached. | ||
| NTF wlsxNVpnMaxSessions | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1165 | A trap which indicates that the VPN session limit is reached. | ||
| NTF wlsxNRapExpiredPSK | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1166 | A trap which indicates that the RAP is using the Expired PSK. | ||
| NTF wlsxNRapWarnExpiredPSK | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1167 | A trap which indicates that the Cached IKE PSK for RAPs will expire soon. | ||
| NTF wlsxNConnectionResetWithLocal | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1168 | A trap which indicates that tcp connection between master controller and local controller has been lost. | ||
| NTF wlsxNApOnBackupController | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1169 | A trap which indicates that the AP has registered with the backup controller. | ||
| NTF wlsxClientFloodAttack | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1170 | This trap indicates that the number of potential fake clients detected by an AP has exceeded the configured IDS threshold. This is the total number of fake clients observed across all bands. For more info check: http://www.wve.org/entries/show/WVE-2005-0056 | ||
| NTF wlsxValidClientNotUsingEncryption | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1171 | This trap indicates that an AP detected an unencrypted data frame between a valid client and an access point. | ||
| NTF wlsxAdhocUsingValidSSID | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1172 | This trap indicates that an AP detected an ad hoc network using a valid/protected SSID. For more info check: http://www.wve.org/entries/show/WVE-2005-0008 | ||
| NTF wlsxAPSpoofingDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1173 | This trap indicates that an AP detected that one of its virtual APs is being spoofed using MAC spoofing. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 | ||
| NTF wlsxClientAssociatingOnWrongChannel | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1174 | This trap indicates that an AP detected a client trying to associate to one of its BSSIDs on the wrong channel. This can be a sign that the BSSID is being spoofed in order to fool the client into thinking the AP is operating on another channel. | ||
| NTF wlsxNDisconnectStationAttack | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1175 | This trap indicates that an AP has determined that a client is under Disconnect Attack because the rate of Assoc/Reassoc Response packets received by that client exceeds the configured threshold. For more info check: http://www.wve.org/entries/show/WVE-2005-0045 http://www.wve.org/entries/show/WVE-2005-0046 http://www.wve.org/entries/show/WVE-2005-0048 | ||
| NTF wlsxNStaUnAssociatedFromUnsecureAP | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1176 | This trap indicates that an AP that had previously detected a client association to a Rogue access point is no longer detecting that association. | ||
| NTF wlsxOmertaAttack | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1177 | This trap indicates that an AP detected an Omerta attack. For more info check: http://www.wve.org/entries/show/WVE-2005-0053 | ||
| NTF wlsxTKIPReplayAttack | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1178 | This trap indicates that an AP detected a TKIP replay attack. If successful this could be the precursor to more advanced attacks. For more info check: http://www.wve.org/entries/show/WVE-2008-0013 | ||
| NTF wlsxChopChopAttack | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1179 | This trap indicates that an AP detected a ChopChop attack. For more info check: http://www.wve.org/entries/show/WVE-2006-0038 | ||
| NTF wlsxFataJackAttack | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1180 | This trap indicates that an AP detected a FATA-Jack attack. For more info check: http://www.wve.org/entries/show/WVE-2006-0057 | ||
| NTF wlsxInvalidAddressCombination | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1181 | This trap indicates that an AP detected an invalid source and destination combination. For more info check: http://www.wve.org/entries/show/WVE-2008-0011 | ||
| NTF wlsxValidClientMisassociation | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1182 | This trap indicates that an AP detected a misassociation between a valid client and an unsafe AP. | ||
| NTF wlsxMalformedHTIEDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1183 | This trap indicates that an AP detected a malformed HT Information Element. This can be the result of a misbehaving wireless driver or it may be an indication of a new wireless attack. | ||
| NTF wlsxMalformedAssocReqDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1184 | This trap indicates that an AP detected a malformed association request with a NULL SSID. For more info check: http://www.wve.org/entries/show/WVE-2008-0010 | ||
| NTF wlsxOverflowIEDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1185 | This trap indicates that an AP detected a management frame with a malformed information element. The declared length of the element is larger than the entire frame containing the element. This may be used to corrupt or crash wireless drivers. For more info check: http://www.wve.org/entries/show/WVE-2008-0008 | ||
| NTF wlsxOverflowEAPOLKeyDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1186 | This trap indicates that an AP detected a key in an EAPOL Key message with a specified length greater than the length of the entire message. For more info check: http://www.wve.org/entries/show/WVE-2008-0009 | ||
| NTF wlsxMalformedFrameLargeDurationDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1187 | This trap indicates that an AP detected an unusually large duration in a wireless frame. This may be an attempt to block other devices from transmitting. For more info check: http://www.wve.org/entries/show/WVE-2005-0051 | ||
| NTF wlsxMalformedFrameWrongChannelDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1188 | This trap indicates that an AP detected a beacon on one channel advertising another channel. This could be an attempt to lure clients away from a valid AP. For more info check: http://www.wve.org/entries/show/WVE-2006-0050 | ||
| NTF wlsxMalformedAuthFrame | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1189 | This trap indicates that an AP detected an authentication frame with either a bad algorithm (similar to Fata-Jack) or a bad transaction. For more info check: http://www.wve.org/entries/show/WVE-2006-0057 | ||
| NTF wlsxCTSRateAnomaly | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1190 | This trap indicates that the rate of CTS packets received by an AP exceeds the configured IDS threshold. | ||
| NTF wlsxRTSRateAnomaly | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1191 | This trap indicates that the rate of RTS packets received by an AP exceeds the configured IDS threshold. | ||
| NTF wlsxNRogueAPDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1192 | This trap indicates that an unauthorized access point is connected to the wired network. The access point is classified as Rogue by the system. | ||
| NTF wlsxNRogueAPResolved | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1193 | This trap indicates that a previously detected access point, classified as Rogue, is either no longer present in the network or it changed its state. | ||
| NTF wlsxNeighborAPDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1194 | This trap indicates that an access point has been classified as a Neighbor by the system. | ||
| NTF wlsxNInterferingAPDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1195 | This trap indicates that an access point has been classified as Interfering by the system. The access point is declared Interfering because it is not authorized, nor has it been classified as a Rogue. | ||
| NTF wlsxNSuspectRogueAPDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1196 | This trap indicates that an access point, classified as Suspected Rogue, is detected by the system. The AP is suspected to be rogue with the supplied confidence level. | ||
| NTF wlsxNSuspectRogueAPResolved | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1197 | This trap indicates that a previously detected access point, classified as Suspected Rogue, is either no longer present in the network or has changed its state. | ||
| NTF wlsxBlockAckAttackDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1198 | This trap indicates that an attempt has been made to deny service to the source address by spoofing a block ACK add request that sets a sequence number window outside the currently used window. For more info check: http://www.wve.org/entries/show/WVE-2008-0006 | ||
| NTF wlsxHotspotterAttackDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1199 | This trap indicates that a new AP has appeared immediately following a client probe request. This is indicative of the Hotspotter tool or similar that attempts to trap clients with a fake hotspot or other wireless network. For more info check: http://www.wve.org/entries/show/WVE-2005-0054 | ||
| NTF wlsxNSignatureMatch | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1200 | This trap indicates that an AP detected a signature match in a frame. | ||
| NTF wlsxNSignatureMatchNetstumbler | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1201 | This trap indicates that an AP detected a signature match for Netstumbler in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0025 | ||
| NTF wlsxNSignatureMatchAsleap | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1202 | This trap indicates that an AP detected a signature match for ASLEAP in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0027 | ||
| NTF wlsxNSignatureMatchAirjack | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1203 | This trap indicates that an AP detected a signature match for Airjack in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0018 | ||
| NTF wlsxNSignatureMatchNullProbeResp | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1204 | This trap indicates that an AP detected a signature match for Null-Probe-Response in a frame. For more info check: http://www.wve.org/entries/show/WVE-2006-0064 | ||
| NTF wlsxNSignatureMatchDeauthBcast | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1205 | This trap indicates that an AP detected a signature match for Deauth-Broadcast in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0045 | ||
| NTF wlsxNSignatureMatchDisassocBcast | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1206 | This trap indicates that an AP detected a signature match for Disassoc-Broadcast in a frame. For more info check: http://www.wve.org/entries/show/WVE-2005-0019 http://www.wve.org/entries/show/WVE-2005-0046 | ||
| NTF wlsxNSignatureMatchWellenreiter | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1207 | This trap indicates that an AP detected a signature match for Wellenreiter in a frame. For more info check: http://www.wve.org/entries/show/WVE-2006-0058 | ||
| NTF wlsxAPDeauthContainment | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1208 | This trap indicates that an AP has attempted to contain an access point by disconnecting its client. | ||
| NTF wlsxClientDeauthContainment | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1209 | This trap indicates that an AP has attempted to contain a client by disconnecting it from the AP that it is associated with. | ||
| NTF wlsxAPWiredContainment | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1210 | This trap indicates that an AP has attempted to contain an access point by disrupting traffic to its client on the wired interface. | ||
| NTF wlsxClientWiredContainment | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1211 | This trap indicates that an AP has attempted to contain a client by disrupting traffic to it on the wired interface. | ||
| NTF wlsxAPTaggedWiredContainment | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1212 | This trap indicates that an AP has attempted to contain an access point by disrupting traffic to its client on the wired interface. | ||
| NTF wlsxClientTaggedWiredContainment | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1213 | This trap indicates that an AP has attempted to contain a client by disrupting traffic to it on the wired interface. | ||
| NTF wlsxTarpitContainment | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1214 | This trap indicates that an AP has attempted to contain an access point by moving a client that is attempting to associate to it to a tarpit. | ||
| NTF wlsxVoiceClientLocationUpdate | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1215 | This trap indicates that the location of voice client has been changed. | ||
| NTF wlsxAPChannelChange | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1216 | This trap indicates that an AP changed its channel. | ||
| NTF wlsxAPPowerChange | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1217 | This trap indicates that an AP changed its transmit power level. | ||
| NTF wlsxAPModeChange | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1218 | This trap indicates that an AP changed its mode from AP to APMonitor or vice versa. | ||
| NTF wlsxUserEntryAttributesChanged | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1219 | This trap indicates that the user entry attributes have changed. | ||
| NTF wlsxPowerSaveDosAttack | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1220 | This trap indicates that an AP detected a Power Save DoS attack. | ||
| NTF wlsxNAPMasterStatusChange | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1221 | This trap indicates that the status of the AP as seen by the master controller has changed. | ||
| NTF wlsxNAdhocUsingValidSSID | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1222 | This trap indicates that an AP detected an ad hoc network node using a valid/protected SSID. For more info check: http://www.wve.org/entries/show/WVE-2005-0008 | ||
| NTF wlsxCRLExpired | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1223 | This trap indicates that the CRL associated with the particular Trustpoint is expired. | ||
| NTF wlsxMgmtUserAuthenticationFailed | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1224 | This trap indicates that a management user authentication has failed. | ||
| NTF wlsxNConnectionBackfromLocal | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1225 | A trap which indicates that tcp connection between master controller and local controller is back. | ||
| NTF wlsxAPNumUpgradeFailure | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1226 | A trap which indicates the number of upgrade failure of an access point. | ||
| NTF wlsxAPNumWarmStarts | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1227 | A trap which indicates the number of warm starts of an access point. | ||
| NTF wlsxAPNumColdStarts | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1228 | A trap which indicates the number of cold starts of an access point. | ||
| NTF wlsxAPNumDown | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1229 | A trap which indicates the number of down alarms of an access point. | ||
| NTF wlsxAPNumRadioDown | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1230 | A trap which indicates the number of radio down alarms of an access point. | ||
| NTF wlsxNumClockSyncErrors | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1231 | A trap which indicates the total number of clock sync errors between the switch and access points. | ||
| NTF wlsxNumColdStart | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1232 | A trap which indicates the number of cold-starts of the switch. | ||
| NTF wlsxNumWarmStart | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1233 | A trap which indicates the number of warm-starts of the switch. | ||
| NTF wlsxWirelessHostedNetworkDetected | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1234 | This trap indicates that an AP detected a wireless client that is hosting a softAP. The softAP could be used to share the hosting client's wired or wireless network connection with other wireless users. | ||
| NTF wlsxClientAssociatedToHostedNetwork | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1235 | This trap indicates that an AP detected that a wireless client associated to an access point that is hosted by another wireless client. | ||
| NTF wlsxThresholdAbove | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1236 | A trap indicates a particular resource under monitoring has gone above the threshold specified. | ||
| NTF wlsxThresholdBelow | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1237 | A trap indicates a particular resource under monitoring has come below the threshold specified. | ||
| NTF wlsxWirelessHostedNetworkContainment | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1238 | This trap indicates that containment is being enforced on a client associated to a hosted network. | ||
| NTF wlsxHostOfWirelessNetworkContainment | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1239 | This trap indicates that containment is being enforced on a client that is hosting a wireless hosted network. | ||
| NTF wlsxEnhancedAdhocContainment | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1240 | This trap indicates that an AP has attempted to contain an adhoc node by disconnecting it from other members of the adhoc network. | ||
| NTF wlsxPowerSupplyOKTrap | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1241 | This trap indicates that the system power supply condition have returned to normal operation status. | ||
| NTF wlsxPowerSupplyFailureTrap | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1242 | A trap which indicates that the power supply has failed. | ||
| NTF wlsxFanTrayRemovedTrap | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1243 | A Trap which indicates that a fan tray is removed. | ||
| NTF wlsxFanTrayInsertedTrap | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1244 | A Trap which indicates that a fan tray is inserted. | ||
| NTF wlsxPowerSupplyMissingTrap | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1245 | A Trap which indicates that the power supply is missing. | ||
| NTF wlsxStackTopologyChangeTrap | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1246 | When change happens in any topology of the stack element in the stack, then a notification is sent to the Management Entity. | ||
| NTF wlsxStackIfStateChangeTrap | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1247 | When any stacking interface in any stack element joins or leaves stacking topology, then a notification is sent to the Management Entity with slot and interface information. | ||
| NTF wlsxLicenseServerExpiry | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1248 | A Trap which indicates that licenses sent from the license server will expire in wlsxTrapLicenseServerDaysRemaining days. | ||
| NTF wlsxLicenseClientExpiry | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1249 | A Trap which indicates that licenses contributed by a license client will expire in wlsxTrapLicenseClientDaysRemaining days. | ||
| NTF wlsxIfStateChangeTrap | 1.3.6.1.4.1.14823.2.3.1.11.1.2.1250 | When the link state of an interface changes due to reason specified by wlsxIfStateChangeReason object, a notification is sent to the Management Entity with reason for this state change and interface information. |
RFC description
Aruba wireless switch trap definitions for events including AP status, authentication changes, and network topology events.
Start monitoring Aruba wireless LAN controllers, Aruba switches (stacked) (AP-connect/client-auth/ARM/VRRP notification status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.