USR-GWCWAN-MIB

All MIBs › USR-GWCWAN-MIB

Organization: CommWorks Corporation, a 3Com Company

Last Updated: 2002-05-05

Category: CommWorks/3Com Access Equipment

Description: Manages WAN interfaces and gateway controller WAN connectivity on CommWorks/3Com carrier platforms.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is USR-GWCWAN-MIB?

USR-GWCWAN-MIB is a CommWorks (US Robotics/3Com) enterprise MIB covering WAN interface and gateway controller connectivity management on their carrier access platforms, part of the broader CommWorks Network Element management family. It exposes configuration and status data about WAN-side interfaces and the gateway controller function that ties access equipment into the carrier's WAN. Its monitoring value lies in software/link status: verifying that WAN interfaces on the gateway controller are up and correctly configured, which helps diagnose a loss of upstream carrier connectivity distinct from a subscriber-facing interface fault. It is part of the same commWorks enterprise MIB family as related Network Element MIBs, implying shared indexing/identification conventions with sibling CommWorks MIBs. It is deployed on CommWorks/3Com carrier access gateway platforms providing WAN uplink connectivity for aggregated subscriber traffic. Engineers can download the USR-GWCWAN-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in USR-GWCWAN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

CommWorks/3Com carrier access gateway platforms

Monitoring Examples

No sample object names were provided for this module in the source data; based on its description, one would expect WAN interface status/configuration objects tied to a gateway controller entity, likely indexed by WAN port or trunk identifier. An administrator would poll such objects to confirm the gateway controller's WAN uplink is operational, which would explain a site-wide loss of upstream connectivity if the interface shows a down or degraded state.

Imported Objects

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DisplayString

From USR-DEFINITIONS-MIB

InterfaceIndex
common	OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
usrGwcwan	1.3.6.1.4.1.429.4.58			The commWorks enterprise defined MIB objects for the Network Element.
usrGwcwanIfTable	1.3.6.1.4.1.429.4.58.1		not-accessible	A list of Gwcwan interface entries.
usrGwcwanIfEntry	1.3.6.1.4.1.429.4.58.1.1		not-accessible	Parameter values for a Gwcwan interfaces.
NUM usrGwcwanIfIndex	1.3.6.1.4.1.429.4.58.1.1.1	InterfaceIndex	read-only	The value of ifIndex for the port. By convention and if possible, hardware port numbers map directly to external connectors. The value for each port must remain constant at least from one re-initialization of the network management agent to the next.
STR usrGwcwanIfName	1.3.6.1.4.1.429.4.58.1.1.2	DisplayString	read-only	The textual name of the interface. It is of the form wan:# for physical interfaces and of the form wan:#/linkname for logicalinterfaces where # is the physical interface this logical interface resides on, and linkname is assigned by the administrator.
INT usrGwcwanIfType	1.3.6.1.4.1.429.4.58.1.1.3	INTEGER	read-only	This helps determine the type of physical interface / NIC Type/ WAN Driver Type.
usrGwcwanV35IfTable	1.3.6.1.4.1.429.4.58.2		not-accessible	A list of Gwcwan V35 virtual interface entries.
usrGwcwanV35IfEntry	1.3.6.1.4.1.429.4.58.2.1		not-accessible	Parameter values for V35 Gwcwan virtual interface.
NUM usrGwcwanV35IfIndex	1.3.6.1.4.1.429.4.58.2.1.1	InterfaceIndex	read-only	The value of ifIndex for the port. By convention and if possible, hardware port numbers map directly to external connectors. The value for each port must remain constant at least from one re-initialization of the network management agent to the next.
INT usrGwcwanV35ClockRefMode	1.3.6.1.4.1.429.4.58.2.1.2	INTEGER	read-write	Valid only when usrGwcwanIfType is usrGwcwanV35. The clock ref mode of this v35 interface
INT usrGwcwanV35ClockInvertedMode	1.3.6.1.4.1.429.4.58.2.1.3	INTEGER	read-write	Valid only when usrGwcwanIfType is usrGwcwanV35. The Clock inverted mode
INT usrGwcwanV35FlagIdlePattern	1.3.6.1.4.1.429.4.58.2.1.4	INTEGER	read-write	Valid only when usrGwcwanIfType is usrGwcwanV35. This mib is an addon to rfc1659 rs232SyncPortIdlePattern mib. rfc1659 does not support idle pattern as flag (7F). If this flag is set to flagIdlePattern, then Pilgrim sets wapi idle pattern to flag. Other wise, Pilgrim sets wapi according the value set in rs232SyncPortIdlePattern.
INT usrGwcwanV35PortType	1.3.6.1.4.1.429.4.58.2.1.5	INTEGER	read-write	The port's hardware type. This is actually a subset of rs232PortType parameter defined by RFC1659. It was necessary to re-define this variable since Write access is not allowed to the parameter defined by RFC1659.
usrGwcwanT1E1IfTable	1.3.6.1.4.1.429.4.58.3		not-accessible	A list of Gwcwan T1E1 virtual interface entries.
usrGwcwanT1E1IfEntry	1.3.6.1.4.1.429.4.58.3.1		not-accessible	Parameter values for T1E1 Gwcwan virtual interface.
NUM usrGwcwanT1E1IfIndex	1.3.6.1.4.1.429.4.58.3.1.1	InterfaceIndex	read-only	The value of ifIndex for the port. By convention and if possible, hardware port numbers map directly to external connectors. The value for each port must remain constant at least from one re-initialization of the network management agent to the next.
INT usrGwcwanDS1CableLen	1.3.6.1.4.1.429.4.58.3.1.2	INTEGER	read-write	Valid only when usrGwcwanIfType is usrGwcwanDS1. The cable length of DS1 interface. If the interface is long haul, use usrGwcwanDS1CableLenLongHaul. Otherwise, use specified cable length.
INT usrGwcwanDS1LineBuildout	1.3.6.1.4.1.429.4.58.3.1.3	INTEGER	read-write	Valid only when usrGwcwanIfType is usrGwcwanDS1. The line build out of DS1 interface.
usrGwcwanWSOCKIfTable	1.3.6.1.4.1.429.4.58.4		not-accessible	A list of Gwcwan WSOCK virtual interface entries.
usrGwcwanWSOCKIfEntry	1.3.6.1.4.1.429.4.58.4.1		not-accessible	Parameter values for WSOCK Gwcwan virtual interface.
NUM usrGwcwanWSOCKIfIndex	1.3.6.1.4.1.429.4.58.4.1.1	InterfaceIndex	read-only	The value of ifIndex for the port. By convention and if possible, hardware port numbers map directly to external connectors. The value for each port must remain constant at least from one re-initialization of the network management agent to the next.
INT usrGwcwanIPConnType	1.3.6.1.4.1.429.4.58.4.1.2	INTEGER	read-write	Valid only when usrGwcwanIfType is usrGwcwanWSOCK. The type of IP service to use to make the sockets connection (UDP or TCP).
IP usrGwcwanRemoteIp	1.3.6.1.4.1.429.4.58.4.1.3	IpAddress	read-write	Valid only when usrGwcwanIfType is usrGwcwanWSOCK. The remote IP address this virtual port sends to.
I32 usrGwcwanRemotePort	1.3.6.1.4.1.429.4.58.4.1.4	Integer32	read-write	Valid only when usrGwcwanIfType is usrGwcwanWSOCK. The remote UDP/IP port this virtual port sends to.
I32 usrGwcwanLocalPort	1.3.6.1.4.1.429.4.58.4.1.5	Integer32	read-write	Valid only when usrGwcwanIfType is usrGwcwanWSOCK. The local UDP/IP port this virtual port listens to.
usrGwcwanT1E1TrapEnaTable	1.3.6.1.4.1.429.4.58.5		not-accessible	A trap enable table that defines a column for every trap that a DS1 entity can generate.
usrGwcwanT1E1TrapEnaEntry	1.3.6.1.4.1.429.4.58.5.1		not-accessible	There is one entry in this table for every DS1 that exists in the chassis.
I32 usrGwcwanT1E1TrapEnaDS1Index	1.3.6.1.4.1.429.4.58.5.1.1	Integer32	read-only	The value of ifIndex for the DS1/ES1 port. By convention and if possible, hardware port numbers map directly to external connectors. The value for each port must remain constant at least from one re-initialization of the network management agent to the next.
INT usrGwcwanT1E1TrapEnaYellowAlarm	1.3.6.1.4.1.429.4.58.5.1.2	INTEGER	read-write	Enable the generation of an SNMP trap for Far-End Loss of Frame condition (signaled by a received Yellow Alarm) on the specified DS1. This corresponds to dsx1RcvFarEndLOF bit in dsx1LineStatus variable
INT usrGwcwanT1E1TrapEnaSndYellowAlarm	1.3.6.1.4.1.429.4.58.5.1.3	INTEGER	read-write	Enable the generation of an SNMP trap for Near End Sending Yellow Alarm condition on the specified DS1. This corresponds to dsx1XmtFarEndLOF bit in dsx1LineStatus variable
INT usrGwcwanT1E1TrapEnaAlarmIndSignal	1.3.6.1.4.1.429.4.58.5.1.4	INTEGER	read-write	Enable the generation of an SNMP trap for Far End Sending Alarm Indication Signal condition on the specified DS1. This corresponds to dsx1RcvAIS bit in dsx1LineStatus variable
INT usrGwcwanT1E1TrapEnaSndAlarmIndSignal	1.3.6.1.4.1.429.4.58.5.1.5	INTEGER	read-write	Enable the generation of an SNMP trap for Near End Sending Alarm Indication Signal condition on the specified DS1. This corresponds to dsx1XmtAIS bit in dsx1LineStatus variable
INT usrGwcwanT1E1TrapEnaRedAlarm	1.3.6.1.4.1.429.4.58.5.1.6	INTEGER	read-write	Enable the generation of an SNMP trap for Near End Loss Of Frame (in red alarm condition) condition on the specified DS1. This corresponds to dsx1LossOfFrame bit in dsx1LineStatus variable
INT usrGwcwanT1E1TrapEnaLossOfSignal	1.3.6.1.4.1.429.4.58.5.1.7	INTEGER	read-write	Enable the generation of an SNMP trap for Near End Loss Of Signal condition on the specified DS1. This corresponds to dsx1LossOfSignal bit in dsx1LineStatus variable
INT usrGwcwanT1E1TrapEnaloopBack	1.3.6.1.4.1.429.4.58.5.1.8	INTEGER	read-write	Enable the generation of an SNMP trap for Near End loopback condition on the specified DS1. This corresponds to dsx1LoopbackState bit in dsx1LineStatus variable
INT usrGwcwanT1E1TrapEnaRcvTestCode	1.3.6.1.4.1.429.4.58.5.1.9	INTEGER	read-write	Enable the generation of an SNMP trap for Near End test code condition on the specified DS1. This corresponds to dsx1RcvTestCode bit in dsx1LineStatus variable
usrGwcwanTraps	1.3.6.1.4.1.429.4.58.6
NTF usrGwcwanT1E1YellowAlarm	1.3.6.1.4.1.429.4.58.6.1			This trap is generated for an active Far-End Loss of Frame condition (signaled by a received Yellow Alarm) on the specified DS1.
NTF usrGwcwanT1E1ClrYellowAlarm	1.3.6.1.4.1.429.4.58.6.2			This trap is generated when Far-End Loss of Frame condition (signaled by a received Yellow Alarm) clears on the specified DS1.
NTF usrGwcwanT1E1SndYellowAlarm	1.3.6.1.4.1.429.4.58.6.3			This trap is generated for an active Near End Sending Yellow Alarm condition on the specified DS1.
NTF usrGwcwanT1E1ClrSndYellowAlarm	1.3.6.1.4.1.429.4.58.6.4			This trap is generated when Near End Sending Yellow Alarm condition clears on the specified DS1.
NTF usrGwcwanT1E1AlarmIndSignal	1.3.6.1.4.1.429.4.58.6.5			This trap is generated for an active Far End Sending Alarm Indication Signal condition on the specified DS1.
NTF usrGwcwanT1E1ClrAlarmIndSignal	1.3.6.1.4.1.429.4.58.6.6			This trap is generated when Far End Sending Alarm Indication Signal condition clears on the specified DS1.
NTF usrGwcwanT1E1SndAlarmIndSignal	1.3.6.1.4.1.429.4.58.6.7			This trap is generated for an active Near End Sending Alarm Indication Signal condition on the specified DS1.
NTF usrGwcwanT1E1ClrSndAlarmIndSignal	1.3.6.1.4.1.429.4.58.6.8			This trap is generated when Near End Sending Alarm Indication Signal condition clears on the specified DS1.
NTF usrGwcwanT1E1RedAlarm	1.3.6.1.4.1.429.4.58.6.9			This trap is generated for an active Near End Loss Of Frame (in red alarm condition) condition on the specified DS1.
NTF usrGwcwanT1E1ClrRedAlarm	1.3.6.1.4.1.429.4.58.6.10			This trap is generated when Near End Loss Of Frame (in red alarm condition) condition clears on the specified DS1.
NTF usrGwcwanT1E1LossOfSignal	1.3.6.1.4.1.429.4.58.6.11			This trap is generated for an active Near End Loss Of Signal condition on the specified DS1.
NTF usrGwcwanT1E1ClrLossOfSignal	1.3.6.1.4.1.429.4.58.6.12			This trap is generated when Near End Loss Of Signal condition clears on the specified DS1.
NTF usrGwcwanT1E1loopBack	1.3.6.1.4.1.429.4.58.6.13			This trap is generated for an active Near End loopback condition on the specified DS1.
NTF usrGwcwanT1E1ClrloopBack	1.3.6.1.4.1.429.4.58.6.14			This trap is generated when Near End loopback condition clears on the specified DS1.
NTF usrGwcwanT1E1RcvTestCode	1.3.6.1.4.1.429.4.58.6.15			This trap is generated for an active Near End test code condition on the specified DS1.
NTF usrGwcwanT1E1ClrRcvTestCode	1.3.6.1.4.1.429.4.58.6.16			This trap is generated when Near End test code condition clears on the specified DS1.

RFC description

Manages gateway WAN interfaces and connections for CommWorks (3Com) network elements.

Start monitoring CommWorks/3Com carrier access gateway platforms (WAN interface/gateway-controller link status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download USR-GWCWAN-MIB

What Is USR-GWCWAN-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description