TNPP-OPT-MIB

All MIBs › TNPP-OPT-MIB

Category: Legacy and Example MIBs

Description: Defines TNPP protocol option parameters and configuration objects for network management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TNPP-OPT-MIB?

This MIB's short description and object names appear mismatched: it is nominally described as a TNPP (Telocator Network Paging Protocol) option-parameter module, but its only sampled objects (cdx6500PCTPortProtocolGroup, cdx6500PSTPortProtocolGroup) carry a "cdx6500" naming pattern more consistent with a Cadant/Arris C4-class cable modem termination system (CMTS) port-protocol conformance group. Given the sparse and empty module description, the module most plausibly exposes conformance/protocol-group objects tying specific port-protocol capabilities to a device's agent capabilities statement rather than live runtime counters. As such it is not clearly usable for monitoring hardware health (uptime, temperature, CPU/memory) or software status the way a data-bearing MIB would be, since only two conformance-group identifiers were sampled. Any dependency is unclear from the available data, though the "cdx6500" prefix suggests it originates from or references a Cadant/Arris CMTS product line rather than a generic paging-protocol implementation. Given this ambiguity, the module should be treated cautiously in a monitoring pipeline until its actual object tree is inspected directly from the source file, which is most easily obtained via a TNPP-OPT-MIB download.

IPNetwork Monitor allows you to monitor SNMP objects defined in TNPP-OPT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

vendor-neutral/unclear — object naming suggests Cadant/Arris CMTS heritage, device type not confirmed by available data

Monitoring Examples

Only two conformance-group style objects were sampled (cdx6500PCTPortProtocolGroup and cdx6500PSTPortProtocolGroup), with no accompanying scalar/table data objects, so this looks like a conformance module rather than one with pollable runtime data — a concrete monitoring scenario cannot be honestly constructed from what's available. An admin encountering this OID tree would more likely use it to confirm which optional port-protocol group an agent claims to support rather than to poll a live value. Further inspection of the raw MIB source would be needed to identify any actual monitorable objects.

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
enterprises

OIDs

OID symbolic	OID numeric	Type	Access	Description
cdx6500	1.3.6.1.4.1.449.2.1
cdx6500CfgProtocolGroup	1.3.6.1.4.1.449.2.1.2.1
cdx6500Configuration	1.3.6.1.4.1.449.2.1.2
cdx6500Controls	1.3.6.1.4.1.449.2.1.4
cdx6500ContTNPPPortEntry	1.3.6.1.4.1.449.2.1.4.15.1.1		not-accessible	Entries in the TNPP Port Control Table.
cdx6500ContTNPPPortTable	1.3.6.1.4.1.449.2.1.4.15.1		not-accessible	This table contains the TNPP Port Control parameters.
cdx6500ContTNPPTable	1.3.6.1.4.1.449.2.1.4.15
cdx6500PCTPortProtocolGroup	1.3.6.1.4.1.449.2.1.2.1.1
cdx6500PPCTTNPPPortEntry	1.3.6.1.4.1.449.2.1.2.1.1.32.1		not-accessible	Entries in the TNPP port configuration table.
cdx6500PPCTTNPPPortTable	1.3.6.1.4.1.449.2.1.2.1.1.32		not-accessible	This table contains the TNPP port configuration parameters.
cdx6500PPSTTNPPPStatTable	1.3.6.1.4.1.449.2.1.3.1.1.33
cdx6500PSTPortProtocolGroup	1.3.6.1.4.1.449.2.1.3.1.1
cdx6500Statistics	1.3.6.1.4.1.449.2.1.3
cdx6500StatProtocolGroup	1.3.6.1.4.1.449.2.1.3.1
cdxProductSpecific	1.3.6.1.4.1.449.2
codex	1.3.6.1.4.1.449
STR tnppPCfgAutocallMnemonic	1.3.6.1.4.1.449.2.1.2.1.1.32.1.11	DisplayString	read-only	This parameter refers to the remote address which will be called by the TNPP PAD port. Specifies the Mnemonic Address for Autocall.
INT tnppPCfgAutocallTimeout	1.3.6.1.4.1.449.2.1.2.1.1.32.1.12	INTEGER	read-only	This parameter is the time interval in seconds between call attempts when auto calling. Specifies the time value for retrying AUTOCALL in seconds.
INT tnppPCfgCallControl	1.3.6.1.4.1.449.2.1.2.1.1.32.1.4	INTEGER	read-only	Specifies the mode for X.25 call generation. dtr - X.25 call is generated when DTR is up. Connection type between TNPP PAD and Paging Terminal is DTR. dataDrv - X.25 call is generated on incoming data. Connection type between TNPP PAD and Paging Terminal is SIMP. powerOn - X.25 call is generated on Node Boot/Power On. Connection type between TNPP PAD and Paging Terminal is SIMP. nc - Skipped during configuration.
INT tnppPCfgCANReports	1.3.6.1.4.1.449.2.1.2.1.1.32.1.7	INTEGER	read-only	Specifies whether to log reports generated by TNPP PAD. no - Reports generated due to CANcel frame will not be logged. yes - Reports generated due to CANcel frame will be logged which will be controlled by node parameter. nc - Skipped during configuration.
INT tnppPCfgCRCOption	1.3.6.1.4.1.449.2.1.2.1.1.32.1.5	INTEGER	read-only	Specifies the CRC option. normal - 2 bytes binary CRC. transp - 4 bytes ASCII CRC. nc - Skipped during configuration.
INT tnppPCfgElectricalInterfaceType	1.3.6.1.4.1.449.2.1.2.1.1.32.1.17	INTEGER	read-only	Specify the Electrical Interface Type: V.24 - V.24 Electrical Interface Type V.35 - V.35 Electrical Interface Type V.36 - V.36 Electrical Interface Type X.21 - X.21 Electrical Interface Type NONE - Electrically disabled
INT tnppPCfgHighSpeedElectricalInterfaceOption	1.3.6.1.4.1.449.2.1.2.1.1.32.1.19	INTEGER	read-only	Specify the cable type: NONE - V.35/V.36/X.21 DCE with straight through cable XOVER - V.35/V.36/X.21 DCE with crossover adapter cable
INT tnppPCfgMaxAutocallAttempt	1.3.6.1.4.1.449.2.1.2.1.1.32.1.13	INTEGER	read-only	Specifies the number of Autocall attempts. 0 - No Autocall retry limit.
INT tnppPCfgMaxReconnAttempt	1.3.6.1.4.1.449.2.1.2.1.1.32.1.16	INTEGER	read-only	This specifies the number of times that DCP on the orginating side will attempt to reconnect before clearing the call. If the value is zero no attempt to reconnect will be made.
INT tnppPCfgMaxRSCount	1.3.6.1.4.1.449.2.1.2.1.1.32.1.9	INTEGER	read-only	TNPP PAD port will stop transmission of any new frame to the paging terminal if the number of frames on hold remains above the value of this parameter. Transmission of control frames and retransmission of RS timed out frames will continue. Specifies the maximum number of RS that can be received before the TNPP PAD stops transmission.
INT tnppPCfgPortNumber	1.3.6.1.4.1.449.2.1.2.1.1.32.1.1	INTEGER	read-only	Port Number of the TNPP port.
INT tnppPCfgPortSpeed	1.3.6.1.4.1.449.2.1.2.1.1.32.1.3	INTEGER	read-only	Specifies port speed in bits per second. speed300 : 300 bits per second. speed1200 : 1200 bits per second. speed2400 : 2400 bits per second. speed4800 : 4800 bits per second. speed9600 : 9600 bits per second. speed19200 : 19200 bits per second.
INT tnppPCfgPortType	1.3.6.1.4.1.449.2.1.2.1.1.32.1.2	INTEGER	read-only	Specifies the type of access protocol for this port.
INT tnppPCfgProtectionLevel	1.3.6.1.4.1.449.2.1.2.1.1.32.1.14	INTEGER	read-only	This specifies the level of data or connection protection which will be applied to calls to or from this port. The actual level for a call will be negotiated to the lesser of this level and the level configured for the other end of the call. none - No protection. cpOnly - Connection protection only. fullDcp - Full data and connection protection. nc - Skipped during configuration.
INT tnppPCfgReconnTimeout	1.3.6.1.4.1.449.2.1.2.1.1.32.1.15	INTEGER	read-only	This specifies the number of seconds that DCP on the originating side will wait between reconnection attempts.
INT tnppPCfgRSCount	1.3.6.1.4.1.449.2.1.2.1.1.32.1.8	INTEGER	read-only	TNPP PAD port will flow control the X.25 channel when the number of RSed frames on hold remains at or above the configured value of this parameter. Specifies the limit for RS support by TNPP PAD.
INT tnppPCfgRSSupport	1.3.6.1.4.1.449.2.1.2.1.1.32.1.10	INTEGER	read-only	Specifies whether to respond with RS to local paging terminal in case of X25 link being blocked. no - RS is not transmitted. yes - RS is transmitted. nc - Skipped during configuration.
INT tnppPCfgTANControl	1.3.6.1.4.1.449.2.1.2.1.1.32.1.6	INTEGER	read-only	Specifies whether to accept control characters(ACK/NAK) in the frame. mps2000Mode - Do not accept embedded control characters in the frame. unipageMode - Accept embedded control characters in the frame. nc - Skipped during configuration.
INT tnppPCfgV24ElectricalInterfaceOption	1.3.6.1.4.1.449.2.1.2.1.1.32.1.18	INTEGER	read-only	Specify the Pin 22 option: RI - V.24 uses Pin 22 for Ring Indicator output signal TM - V.24 uses Pin 22 for Test Mode input signal
INT tnppPContPortControl	1.3.6.1.4.1.449.2.1.4.15.1.1.2	INTEGER	write-only	Control operations for the specified TNPP port. boot - Boots the TNPP Port. enable - Enables the TNPP Port. disable - Disables the TNPP Port. busyout - Busyout the TNPP Port. resetstats - Resets the TNPP port statistics.
INT tnppPContPortNumber	1.3.6.1.4.1.449.2.1.4.15.1.1.1	INTEGER	not-accessible	Port number of the TNPP port.
tnppPDataSummaryStatEntry	1.3.6.1.4.1.449.2.1.3.1.1.33.2.1		not-accessible	Entries in the TNPP port statistics data summary table.
tnppPDataSummaryStatTable	1.3.6.1.4.1.449.2.1.3.1.1.33.2		not-accessible	This table contains the TNPP port statistics data summary parameters.
INT tnppPDSStatCharInPerSec	1.3.6.1.4.1.449.2.1.3.1.1.33.2.1.6	INTEGER	read-only	This indicates the rate at which characters have been received by the port per second.
INT tnppPDSStatCharOutPerSec	1.3.6.1.4.1.449.2.1.3.1.1.33.2.1.7	INTEGER	read-only	This indicates the rate at which characters have been transmitted by the port per second.
INT tnppPDSStatFramesInPerSec	1.3.6.1.4.1.449.2.1.3.1.1.33.2.1.8	INTEGER	read-only	This indicates the rate at which frames have been received by the port per second.
INT tnppPDSStatFramesOutPerSec	1.3.6.1.4.1.449.2.1.3.1.1.33.2.1.9	INTEGER	read-only	This indicates the rate at which frames have been transmitted by the port per second.
INT tnppPDSStatPortNumber	1.3.6.1.4.1.449.2.1.3.1.1.33.2.1.1	INTEGER	read-only	Port Number of the TNPP port.
CTR tnppPDSStatTotalCharIn	1.3.6.1.4.1.449.2.1.3.1.1.33.2.1.2	Counter	read-only	This indicates the total number of characters that have been received by the port.
CTR tnppPDSStatTotalCharOut	1.3.6.1.4.1.449.2.1.3.1.1.33.2.1.3	Counter	read-only	This indicates the total number of characters that have been transmitted by the port.
CTR tnppPDSStatTotalFramesIn	1.3.6.1.4.1.449.2.1.3.1.1.33.2.1.4	Counter	read-only	This indicates the total number of frames that have been received by the port.
CTR tnppPDSStatTotalFramesOut	1.3.6.1.4.1.449.2.1.3.1.1.33.2.1.5	Counter	read-only	This indicates the total number of frames that have been transmitted by the port.
tnppPFrameSummaryStatEntry	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1		not-accessible	Entries in the TNPP port statistics frame summary table.
tnppPFrameSummaryStatTable	1.3.6.1.4.1.449.2.1.3.1.1.33.3		not-accessible	This table contains the TNPP port statistics frame summary parameters.
CTR tnppPFSStatACKFramesIn	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.6	Counter	read-only	This indicates the total number of Acknowledgment frames received by the port.
CTR tnppPFSStatACKFramesOut	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.7	Counter	read-only	This indicates the total number of Acknowledgment frames transmitted by the port.
CTR tnppPFSStatCANFramesIn	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.12	Counter	read-only	This indicates the total number of CANcel report frames received by the port.
CTR tnppPFSStatCANFramesOut	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.13	Counter	read-only	This indicates the total number of CANcel report frames transmitted by the port.
CTR tnppPFSStatCRCErrors	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.3	Counter	read-only	This indicates the total number of TNPP frames received with Cyclic Redundancy Check errors .
CTR tnppPFSStatDataFramesInDiscarded	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.20	Counter	read-only	This indicates the total number of data frames received by the port and discarded.
CTR tnppPFSStatDataFramesInPassed	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.18	Counter	read-only	This indicates the total number of valid data frames received by the port.
CTR tnppPFSStatDataFramesOutDiscarded	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.21	Counter	read-only	This indicates the total number of data frames transmitted by the port and discarded.
CTR tnppPFSStatDataFramesOutPassed	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.19	Counter	read-only	This indicates the total number of valid data frames transmitted by the port.
CTR tnppPFSStatENQFramesIn	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.16	Counter	read-only	This indicates the total number of Enquiry frames received by the port.
CTR tnppPFSStatENQFramesOut	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.17	Counter	read-only	This indicates the total number of Enquiry frames transmitted by the port.
CTR tnppPFSStatEOTFramesIn	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.14	Counter	read-only	This indicates the total number of End of Transmission frames received by the port.
CTR tnppPFSStatEOTFramesOut	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.15	Counter	read-only	This indicates the total number of End of Transmission frames transmitted by the port.
CTR tnppPFSStatLinkFramingErrors	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.4	Counter	read-only	This indicates the total number of TNPP framing errors occured (Invalid Header, Invalid Control character, Frame Size Exceeded, Incomplete Frame, etc.,) .
INT tnppPFSStatLinkState	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.2	INTEGER	read-only	This indicates the current link state. init - Initialization state. awaitEnqResp - Await enquiry response state. ready - Ready to communicate state. transmitting - Transmitting state. transmitResponse - Transmit response state. na - Value not available.
CTR tnppPFSStatNAKFramesIn	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.8	Counter	read-only	This indicates the total number of Negative Acknowledgment frames received by the port.
CTR tnppPFSStatNAKFramesOut	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.9	Counter	read-only	This indicates the total number of Negative Acknowledgment frames transmitted by the port.
INT tnppPFSStatPortNumber	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.1	INTEGER	read-only	Port number of the TNPP port.
CTR tnppPFSStatProtocolErrors	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.5	Counter	read-only	This indicates the number of protocol errors due to unexpected events.
CTR tnppPFSStatRSFramesIn	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.10	Counter	read-only	This indicates the total number of Request to Stop frames received by the port.
CTR tnppPFSStatRSFramesOut	1.3.6.1.4.1.449.2.1.3.1.1.33.3.1.11	Counter	read-only	This indicates the total number of Request to Stop frames transmitted by the port.
tnppPGenStatEntry	1.3.6.1.4.1.449.2.1.3.1.1.33.1.1		not-accessible	Entries in the TNPP port statistics general parameters table.
tnppPGenStatTable	1.3.6.1.4.1.449.2.1.3.1.1.33.1		not-accessible	This table contains the port statistics general parameters.
CTR tnppPGStatFramingErrors	1.3.6.1.4.1.449.2.1.3.1.1.33.1.1.9	Counter	read-only	This indicates number of framing errors detected by the I/O driver.
INT tnppPGStatHoldQ	1.3.6.1.4.1.449.2.1.3.1.1.33.1.1.15	INTEGER	read-only	This indicates the size of the Hold Queue.
INT tnppPGStatLocalDTEState	1.3.6.1.4.1.449.2.1.3.1.1.33.1.1.10	INTEGER	read-only	This indicates the local DTE state. active - DTE is active. down - DTE is down. na - Value not available.
INT tnppPGStatLocalTerminalQ	1.3.6.1.4.1.449.2.1.3.1.1.33.1.1.13	INTEGER	read-only	This indicates the size of the Local Terminal queue.
CTR tnppPGStatOverrunErrors	1.3.6.1.4.1.449.2.1.3.1.1.33.1.1.8	Counter	read-only	This indicates number of overrun errors detected by the I/O driver.
CTR tnppPGStatParityErrors	1.3.6.1.4.1.449.2.1.3.1.1.33.1.1.7	Counter	read-only	This indicates the number of parity errors counted by the I/O driver.
INT tnppPGStatPortNumber	1.3.6.1.4.1.449.2.1.3.1.1.33.1.1.1	INTEGER	read-only	Port Number of the TNPP port.
INT tnppPGStatPortSpeed	1.3.6.1.4.1.449.2.1.3.1.1.33.1.1.4	INTEGER	read-only	This indicates the port speed in bits per second.
INT tnppPGStatPortStatus	1.3.6.1.4.1.449.2.1.3.1.1.33.1.1.3	INTEGER	read-only	This indicates the operational status of the port. disabled : port is disabled. up : port is up. na : Value not available.
INT tnppPGStatPortType	1.3.6.1.4.1.449.2.1.3.1.1.33.1.1.2	INTEGER	read-only	This indicates the type of access protocol for this port.
INT tnppPGStatPortUtilIn	1.3.6.1.4.1.449.2.1.3.1.1.33.1.1.5	INTEGER	read-only	This indicates the port utilization for the line to port direction.
INT tnppPGStatPortUtilOut	1.3.6.1.4.1.449.2.1.3.1.1.33.1.1.6	INTEGER	read-only	This indicates the port utilization for the port to line direction.
INT tnppPGStatReadyQ	1.3.6.1.4.1.449.2.1.3.1.1.33.1.1.14	INTEGER	read-only	This indicates the size of the Ready Queue.
INT tnppPGStatRemoteDTEState	1.3.6.1.4.1.449.2.1.3.1.1.33.1.1.11	INTEGER	read-only	This indicates the remote DTE state. active - DTE is active. down - DTE is down. na - Value not available.
INT tnppPGStatRemotePadQ	1.3.6.1.4.1.449.2.1.3.1.1.33.1.1.12	INTEGER	read-only	This indicates the size of the remote TNPP PAD queue.

RFC description

Manages TNPP port configuration and statistics on Codex CDX 6500 PAD devices.

Start monitoring vendor/device type unclear, object naming suggests Cadant/Arris CMTS heritage (port-protocol conformance status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TNPP-OPT-MIB

What Is TNPP-OPT-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description