All MIBs › TOW-OPT-MIB
Category: Legacy and Example MIBs
Description: Defines TOW protocol option parameters and configuration objects for network management.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TOW-OPT-MIB?
TOW-OPT-MIB is a private MIB whose module description and sample objects were not available in the provided source excerpt, so its specific internal structure cannot be confirmed with confidence; based on its naming, the short description indicates it defines protocol option parameters and configuration objects for network management under a "TOW" vendor or protocol namespace. Given the paucity of available detail, the general categories it likely covers are configuration/protocol-option settings rather than confirmed hardware sensor or fault data. Without visibility into concrete objects, no specific hardware/software status counters (uptime, temperature, CPU, etc.) can be confirmed as present. Any dependency on other MIBs/standards cannot be determined from the available information. It would presumably be deployed on whatever network device implements the "TOW" protocol referenced by its name, but the exact device class is not verifiable from the data provided. Engineers can download the TOW-OPT-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in TOW-OPT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Codex/Motorola 6500-series statistical multiplexers
Monitoring Examples
No module description or sample object names were available for this MIB, so no concrete, grounded monitoring example can be given without inventing object names; further inspection of the actual MIB source would be needed to describe a realistic polling scenario.
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| enterprises |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| cdx6500 | 1.3.6.1.4.1.449.2.1 | |||
| cdx6500CfgGeneralGroup | 1.3.6.1.4.1.449.2.1.2.2 | |||
| cdx6500Configuration | 1.3.6.1.4.1.449.2.1.2 | |||
| cdx6500TOWCfgEntry | 1.3.6.1.4.1.449.2.1.2.2.22.1 | not-accessible | Configuration parameters for each TOW entry. | |
| STR cdx6500TowCfgEntryName | 1.3.6.1.4.1.449.2.1.2.2.22.1.2 | DisplayString | read-only | Range = 0-20 alphanumeric characters, use the space character to blank field. |
| INT cdx6500TowCfgEntryNum | 1.3.6.1.4.1.449.2.1.2.2.22.1.1 | INTEGER | read-only | Entry number used to reference this table record. |
| STR cdx6500TowCfgInt10Duration | 1.3.6.1.4.1.449.2.1.2.2.22.1.31 | DisplayString | read-only | Format : dd:hh:mm dd : Days . Range 00 to 06. hh : Hours. Range 00 to 23. mm : minutes. Range 00 to 59. This parameter specifies the duration of the interval starting from the start time configured. To check if the end time of the interval is as desired, check the Time of Week intervals under the statistics menu. |
| STR cdx6500TowCfgInt10StartDays | 1.3.6.1.4.1.449.2.1.2.2.22.1.32 | DisplayString | read-only | DDD : This specifies the day. Range is one of MON TUE WED THU FRI SAT SUN. DDD+DDD+DDD : This specifies that the interval has to start on each of these days. The `+' operator implies AND. A maximum of 7 days can be specified. This parameter specifies the days on which the interval has to be applied. That is, the intervals would start on each of these days. |
| STR cdx6500TowCfgInt10StartTime | 1.3.6.1.4.1.449.2.1.2.2.22.1.30 | DisplayString | read-only | This parameter specifies the start time of the interval. Format : hh:mm hh : Is the start hour , with range 00 to 23. mm : Is the start minute, with range 00 to 59. This parameter specifies the start time of the interval. All the intervals configured in an entry do not overlap. Intervals configured in different entries can overlap. |
| STR cdx6500TowCfgInt1Duration | 1.3.6.1.4.1.449.2.1.2.2.22.1.4 | DisplayString | read-only | Format : dd:hh:mm dd : Days . Range 00 to 06. hh : Hours. Range 00 to 23. mm : minutes. Range 00 to 59. This parameter specifies the duration of the interval starting from the start time configured. To check if the end time of the interval is as desired, check the Time of Week intervals under the statistics menu. |
| STR cdx6500TowCfgInt1StartDays | 1.3.6.1.4.1.449.2.1.2.2.22.1.5 | DisplayString | read-only | DDD : This specifies the day. Range is one of MON TUE WED THU FRI SAT SUN. DDD+DDD+DDD : This specifies that the interval has to start on each of these days. The `+' operator implies AND. A maximum of 7 days can be specified. This parameter specifies the days on which the interval has to be applied. That is, the intervals would start on each of these days. |
| STR cdx6500TowCfgInt1StartTime | 1.3.6.1.4.1.449.2.1.2.2.22.1.3 | DisplayString | read-only | This parameter specifies the start time of the interval. Format : hh:mm hh : Is the start hour , with range 00 to 23. mm : Is the start minute, with range 00 to 59. This parameter specifies the start time of the interval. All the intervals configured in an entry do not overlap. Intervals configured in different entries can overlap. |
| STR cdx6500TowCfgInt2Duration | 1.3.6.1.4.1.449.2.1.2.2.22.1.7 | DisplayString | read-only | Format : dd:hh:mm dd : Days . Range 00 to 06. hh : Hours. Range 00 to 23. mm : minutes. Range 00 to 59. This parameter specifies the duration of the interval starting from the start time configured. To check if the end time of the interval is as desired, check the Time of Week intervals under the statistics menu. |
| STR cdx6500TowCfgInt2StartDays | 1.3.6.1.4.1.449.2.1.2.2.22.1.8 | DisplayString | read-only | DDD : This specifies the day. Range is one of MON TUE WED THU FRI SAT SUN. DDD+DDD+DDD : This specifies that the interval has to start on each of these days. The `+' operator implies AND. A maximum of 7 days can be specified. This parameter specifies the days on which the interval has to be applied. That is, the intervals would start on each of these days. |
| STR cdx6500TowCfgInt2StartTime | 1.3.6.1.4.1.449.2.1.2.2.22.1.6 | DisplayString | read-only | This parameter specifies the start time of the interval. Format : hh:mm hh : Is the start hour , with range 00 to 23. mm : Is the start minute, with range 00 to 59. This parameter specifies the start time of the interval. All the intervals configured in an entry do not overlap. Intervals configured in different entries can overlap. |
| STR cdx6500TowCfgInt3Duration | 1.3.6.1.4.1.449.2.1.2.2.22.1.10 | DisplayString | read-only | Format : dd:hh:mm dd : Days . Range 00 to 06. hh : Hours. Range 00 to 23. mm : minutes. Range 00 to 59. This parameter specifies the duration of the interval starting from the start time configured. To check if the end time of the interval is as desired, check the Time of Week intervals under the statistics menu. |
| STR cdx6500TowCfgInt3StartDays | 1.3.6.1.4.1.449.2.1.2.2.22.1.11 | DisplayString | read-only | DDD : This specifies the day. Range is one of MON TUE WED THU FRI SAT SUN. DDD+DDD+DDD : This specifies that the interval has to start on each of these days. The `+' operator implies AND. A maximum of 7 days can be specified. This parameter specifies the days on which the interval has to be applied. That is, the intervals would start on each of these days. |
| STR cdx6500TowCfgInt3StartTime | 1.3.6.1.4.1.449.2.1.2.2.22.1.9 | DisplayString | read-only | This parameter specifies the start time of the interval. Format : hh:mm hh : Is the start hour , with range 00 to 23. mm : Is the start minute, with range 00 to 59. This parameter specifies the start time of the interval. All the intervals configured in an entry do not overlap. Intervals configured in different entries can overlap. |
| STR cdx6500TowCfgInt4Duration | 1.3.6.1.4.1.449.2.1.2.2.22.1.13 | DisplayString | read-only | Format : dd:hh:mm dd : Days . Range 00 to 06. hh : Hours. Range 00 to 23. mm : minutes. Range 00 to 59. This parameter specifies the duration of the interval starting from the start time configured. To check if the end time of the interval is as desired, check the Time of Week intervals under the statistics menu. |
| STR cdx6500TowCfgInt4StartDays | 1.3.6.1.4.1.449.2.1.2.2.22.1.14 | DisplayString | read-only | DDD : This specifies the day. Range is one of MON TUE WED THU FRI SAT SUN. DDD+DDD+DDD : This specifies that the interval has to start on each of these days. The `+' operator implies AND. A maximum of 7 days can be specified. This parameter specifies the days on which the interval has to be applied. That is, the intervals would start on each of these days. |
| STR cdx6500TowCfgInt4StartTime | 1.3.6.1.4.1.449.2.1.2.2.22.1.12 | DisplayString | read-only | This parameter specifies the start time of the interval. Format : hh:mm hh : Is the start hour , with range 00 to 23. mm : Is the start minute, with range 00 to 59. This parameter specifies the start time of the interval. All the intervals configured in an entry do not overlap. Intervals configured in different entries can overlap. |
| STR cdx6500TowCfgInt5Duration | 1.3.6.1.4.1.449.2.1.2.2.22.1.16 | DisplayString | read-only | Format : dd:hh:mm dd : Days . Range 00 to 06. hh : Hours. Range 00 to 23. mm : minutes. Range 00 to 59. This parameter specifies the duration of the interval starting from the start time configured. To check if the end time of the interval is as desired, check the Time of Week intervals under the statistics menu. |
| STR cdx6500TowCfgInt5StartDays | 1.3.6.1.4.1.449.2.1.2.2.22.1.17 | DisplayString | read-only | DDD : This specifies the day. Range is one of MON TUE WED THU FRI SAT SUN. DDD+DDD+DDD : This specifies that the interval has to start on each of these days. The `+' operator implies AND. A maximum of 7 days can be specified. This parameter specifies the days on which the interval has to be applied. That is, the intervals would start on each of these days. |
| STR cdx6500TowCfgInt5StartTime | 1.3.6.1.4.1.449.2.1.2.2.22.1.15 | DisplayString | read-only | This parameter specifies the start time of the interval. Format : hh:mm hh : Is the start hour , with range 00 to 23. mm : Is the start minute, with range 00 to 59. This parameter specifies the start time of the interval. All the intervals configured in an entry do not overlap. Intervals configured in different entries can overlap. |
| STR cdx6500TowCfgInt6Duration | 1.3.6.1.4.1.449.2.1.2.2.22.1.19 | DisplayString | read-only | Format : dd:hh:mm dd : Days . Range 00 to 06. hh : Hours. Range 00 to 23. mm : minutes. Range 00 to 59. This parameter specifies the duration of the interval starting from the start time configured. To check if the end time of the interval is as desired, check the Time of Week intervals under the statistics menu. |
| STR cdx6500TowCfgInt6StartDays | 1.3.6.1.4.1.449.2.1.2.2.22.1.20 | DisplayString | read-only | DDD : This specifies the day. Range is one of MON TUE WED THU FRI SAT SUN. DDD+DDD+DDD : This specifies that the interval has to start on each of these days. The `+' operator implies AND. A maximum of 7 days can be specified. This parameter specifies the days on which the interval has to be applied. That is, the intervals would start on each of these days. |
| STR cdx6500TowCfgInt6StartTime | 1.3.6.1.4.1.449.2.1.2.2.22.1.18 | DisplayString | read-only | This parameter specifies the start time of the interval. Format : hh:mm hh : Is the start hour , with range 00 to 23. mm : Is the start minute, with range 00 to 59. This parameter specifies the start time of the interval. All the intervals configured in an entry do not overlap. Intervals configured in different entries can overlap. |
| STR cdx6500TowCfgInt7Duration | 1.3.6.1.4.1.449.2.1.2.2.22.1.22 | DisplayString | read-only | Format : dd:hh:mm dd : Days . Range 00 to 06. hh : Hours. Range 00 to 23. mm : minutes. Range 00 to 59. This parameter specifies the duration of the interval starting from the start time configured. To check if the end time of the interval is as desired, check the Time of Week intervals under the statistics menu. |
| STR cdx6500TowCfgInt7StartDays | 1.3.6.1.4.1.449.2.1.2.2.22.1.23 | DisplayString | read-only | DDD : This specifies the day. Range is one of MON TUE WED THU FRI SAT SUN. DDD+DDD+DDD : This specifies that the interval has to start on each of these days. The `+' operator implies AND. A maximum of 7 days can be specified. This parameter specifies the days on which the interval has to be applied. That is, the intervals would start on each of these days. |
| STR cdx6500TowCfgInt7StartTime | 1.3.6.1.4.1.449.2.1.2.2.22.1.21 | DisplayString | read-only | This parameter specifies the start time of the interval. Format : hh:mm hh : Is the start hour , with range 00 to 23. mm : Is the start minute, with range 00 to 59. This parameter specifies the start time of the interval. All the intervals configured in an entry do not overlap. Intervals configured in different entries can overlap. |
| STR cdx6500TowCfgInt8Duration | 1.3.6.1.4.1.449.2.1.2.2.22.1.25 | DisplayString | read-only | Format : dd:hh:mm dd : Days . Range 00 to 06. hh : Hours. Range 00 to 23. mm : minutes. Range 00 to 59. This parameter specifies the duration of the interval starting from the start time configured. To check if the end time of the interval is as desired, check the Time of Week intervals under the statistics menu. |
| STR cdx6500TowCfgInt8StartDays | 1.3.6.1.4.1.449.2.1.2.2.22.1.26 | DisplayString | read-only | DDD : This specifies the day. Range is one of MON TUE WED THU FRI SAT SUN. DDD+DDD+DDD : This specifies that the interval has to start on each of these days. The `+' operator implies AND. A maximum of 7 days can be specified. This parameter specifies the days on which the interval has to be applied. That is, the intervals would start on each of these days. |
| STR cdx6500TowCfgInt8StartTime | 1.3.6.1.4.1.449.2.1.2.2.22.1.24 | DisplayString | read-only | This parameter specifies the start time of the interval. Format : hh:mm hh : Is the start hour , with range 00 to 23. mm : Is the start minute, with range 00 to 59. This parameter specifies the start time of the interval. All the intervals configured in an entry do not overlap. Intervals configured in different entries can overlap. |
| STR cdx6500TowCfgInt9Duration | 1.3.6.1.4.1.449.2.1.2.2.22.1.28 | DisplayString | read-only | Format : dd:hh:mm dd : Days . Range 00 to 06. hh : Hours. Range 00 to 23. mm : minutes. Range 00 to 59. This parameter specifies the duration of the interval starting from the start time configured. To check if the end time of the interval is as desired, check the Time of Week intervals under the statistics menu. |
| STR cdx6500TowCfgInt9StartDays | 1.3.6.1.4.1.449.2.1.2.2.22.1.29 | DisplayString | read-only | DDD : This specifies the day. Range is one of MON TUE WED THU FRI SAT SUN. DDD+DDD+DDD : This specifies that the interval has to start on each of these days. The `+' operator implies AND. A maximum of 7 days can be specified. This parameter specifies the days on which the interval has to be applied. That is, the intervals would start on each of these days. |
| STR cdx6500TowCfgInt9StartTime | 1.3.6.1.4.1.449.2.1.2.2.22.1.27 | DisplayString | read-only | This parameter specifies the start time of the interval. Format : hh:mm hh : Is the start hour , with range 00 to 23. mm : Is the start minute, with range 00 to 59. This parameter specifies the start time of the interval. All the intervals configured in an entry do not overlap. Intervals configured in different entries can overlap. |
| cdx6500TOWCfgTable | 1.3.6.1.4.1.449.2.1.2.2.22 | not-accessible | This table contains the configuration parameters for TOW. | |
| cdxProductSpecific | 1.3.6.1.4.1.449.2 | |||
| codex | 1.3.6.1.4.1.449 |
RFC description
Manages Time Of Week scheduling configuration for Codex CDX6500 equipment with interval parameters.
Start monitoring Codex/Motorola statistical multiplexers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.