TELDAT-MON-INTERF-ASL-MIB

All MIBs › TELDAT-MON-INTERF-ASL-MIB

Category: Teldat Router Management

Description: Monitors Teldat router ASL interface operational state, link statistics, and error counters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TELDAT-MON-INTERF-ASL-MIB?

The TELDAT-MON-INTERF-ASL-MIB is a vendor-specific monitoring module for the ASL (asynchronous serial line) interface type on Teldat routers, part of Teldat's family of per-interface-technology MIBs. It exposes the operational state of ASL interfaces along with link statistics and error counters for that serial link type. Its core purpose is monitoring the hardware/link status of the serial interface — whether the line is up or down, and cumulative error counts indicating a degrading or faulty serial connection — functioning much like an extension of the standard ifTable operational-status model but scoped to Teldat's ASL interface type. It likely relies conceptually on the same ifIndex numbering used across Teldat's other interface MIBs, though no direct import was evident here. It is deployed on Teldat routers equipped with asynchronous serial WAN or console links, polled by an NMS to catch link flaps or rising error rates. Engineers can download the TELDAT-MON-INTERF-ASL-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in TELDAT-MON-INTERF-ASL-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Teldat router/gateway (asynchronous serial line interface)

Monitoring Examples

No sample objects were provided for this module; based on its description, it would expose per-ASL-interface operational status (up/down) alongside link statistics and error counters, likely in an indexed table keyed by interface, that an operator would poll to detect a degraded or down asynchronous serial link.

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter

From RFC1213-MIB

DisplayString

From TELDAT-SW-STRUCTURE-MIB

telProdNpMonInterfRouter

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
telProdNpMonInterfASL	1.3.6.1.4.1.2007.4.1.2.2.2.16
telProdNpMonIfcASLGlobalTable	1.3.6.1.4.1.2007.4.1.2.2.2.16.1		not-accessible	This table contains general information about asynchronous serial line interfaces. There will be one entry per each interface of this kind.
telProdNpMonIfcASLGlobalEntry	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1		not-accessible	Each entry contains the interface number that will be the table index used to go over the table, the line speed, the throughput in bits per second, the last throughput, the number of bits per character, the number of stop bits, the parity chosen (if it exists), the number of parity errors, data errors, overrun errors, the amount of time passed since the last port reset and variables to indicate if the SCC loopback mode or echo mode are active, if CD or DSR signal states are ignored and if CD signal is disconnected from internal hardware.
INT telProdNpMonIfcASLGloIndex	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.1	INTEGER	read-only	Interface number. The interface must be asynchronous serial line. It is the table index.
STR telProdNpMonIfcASLGloDriverType	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.2	DisplayString	read-only	Type of physical driverP: (1) DCE, (2) DTE. The variable is a string.
INT telProdNpMonIfcASLGloSpeed	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.3	INTEGER	read-only	Speed of the asynchronous serial line. (Clock speed, in bps).
INT telProdNpMonIfcASLGloThrou	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.4	INTEGER	read-only	Throughput in bits per second. It is the mean effective speed.
INT telProdNpMonIfcASLGloLastThrou	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.5	INTEGER	read-only	Last throughput, in bits per second. It is the mean instantaneous speed.
INT telProdNpMonIfcASLGloBitsChar	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.6	INTEGER	read-only	Number of bits per character.
INT telProdNpMonIfcASLGloStopBits	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.7	INTEGER	read-only	Number of stop bits.
INT telProdNpMonIfcASLGloParitySel	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.8	INTEGER	read-only	Parity chosen (if parity has been chosen). The possible values are: (0) if no parity has been selected, (1) odd, (2) space, (3) even, (4) mark.
INT telProdNpMonIfcASLGloLastResetWeek	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.9	INTEGER	read-only	Weeks passed since the last port reset.
INT telProdNpMonIfcASLGloLastResetDay	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.10	INTEGER	read-only	Days passed since the last port reset: the remaining days that we get after counting the number of weeks that are not enough to form a week, this implies that the value of the variable must be under 7.
INT telProdNpMonIfcASLGloLastResetHour	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.11	INTEGER	read-only	Hours passed since the last reset of the port. If it has passed more than a week, this variable indicates the number of hours to be added to the number of weeks and days, and its value should be under 24 so as not form a complete day.
INT telProdNpMonIfcASLGloLastResetMin	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.12	INTEGER	read-only	Minutes passed since the last reset of the port. This variable indicates the number of minutes since the last hour was added to the hour counter.
INT telProdNpMonIfcASLGloLastResetSec	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.13	INTEGER	read-only	Seconds passed since the last reset of the port. The total time passed will be calculated by adding weeks, days, hours, minutes and seconds since the last reset.
INT telProdNpMonIfcASLGloLoopback	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.14	INTEGER	read-only	This variable indicates if SCC loopback mode is active: transmitter is connected internally to the receiver.
INT telProdNpMonIfcASLGloEcho	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.15	INTEGER	read-only	This variable indicates if SCC echo mode is active: transmitter resends received data.
INT telProdNpMonIfcASLGloIgnoreCD	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.16	INTEGER	read-only	This variable indicates if CD signal state is ignored.
INT telProdNpMonIfcASLGloDisconnectCD	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.17	INTEGER	read-only	This variable indicates if CD signal is disconnected from internal hardware.
INT telProdNpMonIfcASLGloIgnoreDSR	1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.18	INTEGER	read-only	This variable indicates if DSR signal state is ignored.
telProdNpMonIfcASLRS232Table	1.3.6.1.4.1.2007.4.1.2.2.2.16.2		not-accessible	This table contains the signals or circuits RS232. It shows wether the signals are active or not. The entry number is determined by the interface number considered.
telProdNpMonIfcASLRS232Entry	1.3.6.1.4.1.2007.4.1.2.2.2.16.2.1		not-accessible	Each entry contains the interface number of the node considered, which will be the first index used to go over the table, the order number of the circuit inside that interface (second index), which must be between 1 and a maximum value that depends on the conector type (the highest value will be 7), the circuit number (105, 106, 107, 108, 109, 125, 141), its name (RTS, CTS, DSR, DTR, DCD, RI, LL) and wether it is active or not.
INT telProdNpMonIfcASLRS232IfcIndex	1.3.6.1.4.1.2007.4.1.2.2.2.16.2.1.1	INTEGER	read-only	Interface number, which must be synchronous serial line. It is the first table index.
INT telProdNpMonIfcASLRS232CircIndex	1.3.6.1.4.1.2007.4.1.2.2.2.16.2.1.2	INTEGER	read-only	Second table index. This value goes between 1 to the number of this type of circuits, that varies depending on the conector type.
INT telProdNpMonIfcASLRS232Circuit	1.3.6.1.4.1.2007.4.1.2.2.2.16.2.1.3	INTEGER	read-only	RS232 circuit number. The possible values are 105, 106, 107, 108, 109, 125 y 141.
STR telProdNpMonIfcASLRS232Nickname	1.3.6.1.4.1.2007.4.1.2.2.2.16.2.1.4	DisplayString	read-only	Circuit name.
STR telProdNpMonIfcASLRS232State	1.3.6.1.4.1.2007.4.1.2.2.2.16.2.1.5	DisplayString	read-only	Signal state (circuit signals): on, off or unknown.
telProdNpMonIfcASLStatsTable	1.3.6.1.4.1.2007.4.1.2.2.2.16.3		not-accessible	This table contains statistics of asynchronous serial line interfaces.
telProdNpMonIfcASLStatsEntry	1.3.6.1.4.1.2007.4.1.2.2.2.16.3.1		not-accessible	Each entry contains the interface number that is the table index, the variable that shows the output from the last table deletion operation (in get operations) or begins the deletion (in set operations), the number of parity errors, the number of data errors and the number of overrun errors.
INT telProdNpMonIfcASLStatsIndex	1.3.6.1.4.1.2007.4.1.2.2.2.16.3.1.1	INTEGER	read-only	Interface number. The interface must be asynchronous serial line to appear in the table. It is the table index.
INT telProdNpMonIfcASLStatsClear	1.3.6.1.4.1.2007.4.1.2.2.2.16.3.1.2	INTEGER	read-write	This variable when is read shows the output from the last table delete attempt: the value is 2 if the deletion was performed succesfully, 3 if an error ocurred and 4 for an undefined result, that means that nobody has tried to delete the table yet. In set operations, the value 1 (it is the only value that can be assigned by a writing operation) causes a table deletion: frame counters are set to 0.
CTR telProdNpMonIfcASLStatsParityErr	1.3.6.1.4.1.2007.4.1.2.2.2.16.3.1.3	Counter	read-only	Number of parity errors.
CTR telProdNpMonIfcASLStatsDataErr	1.3.6.1.4.1.2007.4.1.2.2.2.16.3.1.4	Counter	read-only	Number of data errors.
CTR telProdNpMonIfcASLStatsOverrun	1.3.6.1.4.1.2007.4.1.2.2.2.16.3.1.5	Counter	read-only	Number of overrun errors.

RFC description

Monitoring for asynchronous serial line interfaces, tracking line speed, throughput, parity errors, and loopback status.

Start monitoring Teldat router/gateway, asynchronous serial line interface (link status/error counters) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TELDAT-MON-INTERF-ASL-MIB

What Is TELDAT-MON-INTERF-ASL-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description