All MIBs › SYMBIOSSDMSMASSSTORAGESYSTEMMIFDEF2-MIB
Category: Legacy and Historical, Storage
Description: Defines Symbios SDM mass storage system MIF objects for legacy SCSI and RAID controller monitoring.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is SYMBIOSSDMSMASSSTORAGESYSTEMMIFDEF2-MIB?
SYMBIOSSDMSMASSSTORAGESYSTEMMIFDEF2-MIB is a legacy vendor MIB derived from Symbios Logic's Storage Device Management (SDM) MIF definitions, targeting SCSI-based mass storage subsystems such as host bus adapters and RAID controllers from the Symbios/LSI (Cosprings) enterprise branch. It exposes component-identification data, hardware and firmware inventory objects, and installation/verification status for storage system components. Its most useful monitoring role is tracking hardware and firmware identity and health, including component manufacturer, product name, hardware version, serial number, and whether a component has passed installation verification (a1Verify), plus separate software component version tracking (a2MajorVersion) for firmware/driver revisions. As a MIF-derived MIB it reflects DMTF MIF/DMI conventions translated into SNMP form rather than a native IETF hierarchy, so it has little overlap with standard interface or host-resource MIBs. It would be deployed on older SCSI/RAID storage controllers and mass-storage subsystems from the Symbios Logic/LSI Logic era, typically inside servers or storage arrays needing component-level asset and health tracking, and administrators maintaining such legacy hardware can download the SYMBIOSSDMSMASSSTORAGESYSTEMMIFDEF2-MIB file to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in SYMBIOSSDMSMASSSTORAGESYSTEMMIFDEF2-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Symbios/LSI Logic SCSI host bus adapters and RAID controllers
- legacy mass storage subsystems
Monitoring Examples
An administrator could poll tComponentid/eComponentid entries alongside a1Manufacturer, a1Product, a1Version, and a1SerialNumber to build an inventory of installed SCSI/RAID components and confirm firmware/hardware versions match expected baselines. Checking a1Installation and a1Verify reveals whether a component was properly installed and passed self-verification, flagging a failed or unverified state as an early sign of a faulty card or connector. The tSoftwareComponentInformation/eSoftwareComponentInformation objects paired with a2MajorVersion let an operator confirm the firmware/driver major version running on the storage controller, useful when auditing for known-vulnerable or outdated firmware.
What Can Be Monitored
- component manufacturer and product identity
- hardware version and serial number
- installation/verification status
- software/firmware major version
- component type/component ID
This MIB depends on
Related MIBs
Imported Objects
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| symbios | 1.3.6.1.4.1.1123 | |||
| cosprings | 1.3.6.1.4.1.1123.3 | |||
| scsi | 1.3.6.1.4.1.1123.3.1 | |||
| fam8xx | 1.3.6.1.4.1.1123.3.1.2 | |||
| id | 1.3.6.1.4.1.1123.3.1.2.4 | |||
| dmtfGroups | 1.3.6.1.4.1.1123.3.1.2.4.1 | |||
| tComponentid | 1.3.6.1.4.1.1123.3.1.2.4.1.1 | not-accessible | This group defines the attributes common to all components. This group is required. | |
| eComponentid | 1.3.6.1.4.1.1123.3.1.2.4.1.1.1 | not-accessible | ||
| STR a1Manufacturer | 1.3.6.1.4.1.1123.3.1.2.4.1.1.1.1 | DmiDisplaystring | read-only | Manufacturer of this component. |
| STR a1Product | 1.3.6.1.4.1.1123.3.1.2.4.1.1.1.2 | DmiDisplaystring | read-only | Product name for this component. |
| STR a1Version | 1.3.6.1.4.1.1123.3.1.2.4.1.1.1.3 | DmiDisplaystring | read-only | Version number of this component. |
| STR a1SerialNumber | 1.3.6.1.4.1.1123.3.1.2.4.1.1.1.4 | DmiDisplaystring | read-only | Serial number for this component |
| DMI a1Installation | 1.3.6.1.4.1.1123.3.1.2.4.1.1.1.5 | DmiDateX | read-only | The installation date and time of this component. The Service Layer assigns this value, the manufacturer should leave it blank. |
| INT a1Verify | 1.3.6.1.4.1.1123.3.1.2.4.1.1.1.6 | INTEGER | read-only | A code that provides a level of verification that the component is still installed and working. |
| tSoftwareComponentInformation | 1.3.6.1.4.1.1123.3.1.2.4.1.2 | not-accessible | Contains additional identifying information about this software component. | |
| eSoftwareComponentInformation | 1.3.6.1.4.1.1123.3.1.2.4.1.2.1 | not-accessible | ||
| STR a2MajorVersion | 1.3.6.1.4.1.1123.3.1.2.4.1.2.1.1 | DmiDisplaystring | read-only | Major version of this software component. |
| STR a2MinorVersion | 1.3.6.1.4.1.1123.3.1.2.4.1.2.1.2 | DmiDisplaystring | read-only | Minor version of this software component. |
| STR a2Revision | 1.3.6.1.4.1.1123.3.1.2.4.1.2.1.3 | DmiDisplaystring | read-only | Revision of this software component. |
| STR a2Build | 1.3.6.1.4.1.1123.3.1.2.4.1.2.1.4 | DmiDisplaystring | read-only | Manufacturer's internal identifier for this compilation. |
| INT a2TargetOperatingSystem | 1.3.6.1.4.1.1123.3.1.2.4.1.2.1.5 | INTEGER | read-only | The operating system for which this software component is intended. |
| STR a2LanguageEdition | 1.3.6.1.4.1.1123.3.1.2.4.1.2.1.6 | DmiDisplaystring | read-only | This identifies the language edition of this component. |
| STR a2IdentificationCode | 1.3.6.1.4.1.1123.3.1.2.4.1.2.1.7 | DmiDisplaystring | read-only | Stock Keeping Unit (SKU) or Part Number for this software component. |
| INT a2InstallableState | 1.3.6.1.4.1.1123.3.1.2.4.1.2.1.8 | INTEGER | read-only | Specifies whether this component describes a software product installed for the purpose of further distribution. |
| INT a2ExecutableState | 1.3.6.1.4.1.1123.3.1.2.4.1.2.1.9 | INTEGER | read-only | Specifies whether this component describes a software product which is executable. |
| tSoftwareSignature | 1.3.6.1.4.1.1123.3.1.2.4.1.3 | not-accessible | The Software Signature Group contains information that can be used to detect this software component. | |
| eSoftwareSignature | 1.3.6.1.4.1.1123.3.1.2.4.1.3.1 | not-accessible | ||
| STR a3FileName | 1.3.6.1.4.1.1123.3.1.2.4.1.3.1.1 | DmiDisplaystring | read-only | The name of a file that can be examined to detect this software component. |
| NUM a3FileSize | 1.3.6.1.4.1.1123.3.1.2.4.1.3.1.2 | DmiInteger | read-only | The size in bytes of a file that can be examined to detect this software component. |
| DMI a3FileDateAndTime | 1.3.6.1.4.1.1123.3.1.2.4.1.3.1.3 | DmiDateX | read-only | The date and time of a file that can be examined to detect this software component. |
| NUM a3FileChecksum | 1.3.6.1.4.1.1123.3.1.2.4.1.3.1.4 | DmiInteger | read-only | The checksum of the first 32 bytes of this file. |
| NUM a3FileCrc1 | 1.3.6.1.4.1.1123.3.1.2.4.1.3.1.5 | DmiInteger | read-only | The 16-bit CRC (ITU-T) on the middle 512k of this file. |
| NUM a3FileCrc2 | 1.3.6.1.4.1.1123.3.1.2.4.1.3.1.6 | DmiInteger | read-only | The 16-bit CRC (ITU-T) on the middle 512k of this file with a modulo-3 offset relative to the beginning of the file. |
| NUM a3FileIndex | 1.3.6.1.4.1.1123.3.1.2.4.1.3.1.7 | DmiInteger | read-only | The index into this software signature table. |
| tFieldReplaceableUnit | 1.3.6.1.4.1.1123.3.1.2.4.1.4 | not-accessible | A Field Replaceable Unit (FRU), is defined as a hardware component which is designed to be separately removable for replacement or repair. For the purposes of this definition, a motherboard and a fixed hard disk are FRUs, whereas a fixed hard disk platter or a chip fixed in place on the motherboard are not FRUs since they are not designed to be separately removable. Each instance within the FRU table should contain the device group and instance data for the associated hardware component. | |
| eFieldReplaceableUnit | 1.3.6.1.4.1.1123.3.1.2.4.1.4.1 | not-accessible | ||
| NUM a4FruIndex | 1.3.6.1.4.1.1123.3.1.2.4.1.4.1.1 | DmiInteger | read-only | The index into the Field Replaceable Unit table. |
| NUM a4DeviceGroupIndex | 1.3.6.1.4.1.1123.3.1.2.4.1.4.1.2 | DmiInteger | read-only | The group ID of the group referencing this Field Replaceable Unit instance. |
| STR a4Description | 1.3.6.1.4.1.1123.3.1.2.4.1.4.1.3 | DmiDisplaystring | read-only | A clear description of this Field Replaceable Unit. |
| STR a4Manufacturer | 1.3.6.1.4.1.1123.3.1.2.4.1.4.1.4 | DmiDisplaystring | read-only | The name of the company manufacturing or providing this Field Replaceable Unit. |
| STR a4Model | 1.3.6.1.4.1.1123.3.1.2.4.1.4.1.5 | DmiDisplaystring | read-only | The manufacturer's model number for this Field Replaceable Unit. |
| STR a4PartNumber | 1.3.6.1.4.1.1123.3.1.2.4.1.4.1.6 | DmiDisplaystring | read-only | A part number by which a replacement part can be ordered for this Field Replaceable Unit. |
| STR a4FruSerialNumber | 1.3.6.1.4.1.1123.3.1.2.4.1.4.1.7 | DmiDisplaystring | read-only | The manufacturer's serial number for this Field Replaceable Unit. |
| STR a4RevisionLevel | 1.3.6.1.4.1.1123.3.1.2.4.1.4.1.8 | DmiDisplaystring | read-only | The revision level of this Field Replaceable Unit. |
| DMI a4WarrantyStartDate | 1.3.6.1.4.1.1123.3.1.2.4.1.4.1.9 | DmiDateX | read-only | The start date of the service warranty for this Field Replaceabl Unit. |
| NUM a4WarrantyDuration | 1.3.6.1.4.1.1123.3.1.2.4.1.4.1.10 | DmiInteger | read-only | The total duration of this Field Replaceable Unit warranty in months. |
| STR a4SupportPhoneNumber | 1.3.6.1.4.1.1123.3.1.2.4.1.4.1.11 | DmiDisplaystring | read-only | The phone number(s) for support for this Field Replaceable Unit. |
| tStorageDevices | 1.3.6.1.4.1.1123.3.1.2.4.1.5 | not-accessible | This group defines the mass storage devices in this system. | |
| eStorageDevices | 1.3.6.1.4.1.1123.3.1.2.4.1.5.1 | not-accessible | ||
| NUM a5StorageDeviceIndex | 1.3.6.1.4.1.1123.3.1.2.4.1.5.1.1 | DmiInteger | read-only | An index into the storage device table. |
| INT a5Type | 1.3.6.1.4.1.1123.3.1.2.4.1.5.1.2 | INTEGER | read-only | The type of this mass storage device. If 'Other' is used, then the Type Description attribute shall be used. |
| STR a5TypeDescription | 1.3.6.1.4.1.1123.3.1.2.4.1.5.1.3 | DmiDisplaystring | read-only | A longer description of the storage device. For example: 3.5 inch flexible diskette drive using diskettes with a maximum capacity of 1.44MB. If 'Other' was specified above, then this field shall be used. Otherwise, the contents of this optional field shall not contradict the Storage Device Type specified above. |
| INT a5WorldwideIdentifierType | 1.3.6.1.4.1.1123.3.1.2.4.1.5.1.4 | INTEGER | read-only | The type of identifier displayed by the Worldwide Identifier attribute. |
| STR a5WorldwideIdentifier | 1.3.6.1.4.1.1123.3.1.2.4.1.5.1.5 | DmiDisplaystring | read-only | The Worldwide identifier for this device. |
| STR a5Sub_identifier | 1.3.6.1.4.1.1123.3.1.2.4.1.5.1.6 | DmiDisplaystring | read-only | The sub-identifier for this storage device (e.g., the device's SCSI logical unit number). |
| NUM a5MediaDataBlockSize | 1.3.6.1.4.1.1123.3.1.2.4.1.5.1.7 | DmiInteger | read-only | The size in bytes of the data blocks used on the storage media. If the media block size is unknown or not consistent across the media, then this value shall be zero. |
| NUM a5FormattedMediaCapacity | 1.3.6.1.4.1.1123.3.1.2.4.1.5.1.8 | DmiInteger64X | read-only | The total size in bytes of this storage media after it has been formatted. |
| INT a5RemovableDevice | 1.3.6.1.4.1.1123.3.1.2.4.1.5.1.9 | INTEGER | read-only | If true, then this storage device is removable (e.g.: PCMCIA device). |
| INT a5DeviceLoaded | 1.3.6.1.4.1.1123.3.1.2.4.1.5.1.10 | INTEGER | read-only | If true, then the storage device is loaded. If the device is not removable, then this value shall be 'TRUE'. |
| INT a5RemovableMedia | 1.3.6.1.4.1.1123.3.1.2.4.1.5.1.11 | INTEGER | read-only | If true, then the media in this storage device is removable. |
| INT a5MediaLoaded | 1.3.6.1.4.1.1123.3.1.2.4.1.5.1.12 | INTEGER | read-only | If true, the media in this storage device is loaded. If the media is not removable, then this value shall be 'TRUE' |
| INT a5Compression | 1.3.6.1.4.1.1123.3.1.2.4.1.5.1.13 | INTEGER | read-only | If true, the storage device supports compression. |
| INT a5Encryption | 1.3.6.1.4.1.1123.3.1.2.4.1.5.1.14 | INTEGER | read-only | If true, the storage device supports encryption. |
| NUM a5FruGroupIndex | 1.3.6.1.4.1.1123.3.1.2.4.1.5.1.15 | DmiInteger | read-only | If this is a Field Replaceable Unit or if it is part of another FRU, this provides an index into the FRU table for this device; 'value = -1' indicates that the group is not a FRU. |
| NUM a5OperationalGroupIndex | 1.3.6.1.4.1.1123.3.1.2.4.1.5.1.16 | DmiInteger | read-only | The index into the Operational State table for this device. |
| tStorageDevicesEvents | 1.3.6.1.4.1.1123.3.1.2.4.1.6 | not-accessible | Storage Devices events. | |
| eStorageDevicesEvents | 1.3.6.1.4.1.1123.3.1.2.4.1.6.1 | not-accessible | ||
| NTF trap1 | 1.3.6.1.4.1.1123.3.1.2.4.1.6.1.0.1 | Rebuild in Progress | ||
| NTF trap2 | 1.3.6.1.4.1.1123.3.1.2.4.1.6.1.0.2 | Storage Device Readying | ||
| NTF trap3 | 1.3.6.1.4.1.1123.3.1.2.4.1.6.1.0.3 | Storage Device Error | ||
| NTF trap4 | 1.3.6.1.4.1.1123.3.1.2.4.1.6.1.0.4 | Self-Monitoring Warning | ||
| INT a6StorageDevicesEventType | 1.3.6.1.4.1.1123.3.1.2.4.1.6.1.1 | INTEGER | read-only | The type of Storage Devices event that has occurred. |
| INT a6EventSeverity | 1.3.6.1.4.1.1123.3.1.2.4.1.6.1.2 | INTEGER | read-only | The severity of this event. |
| INT a6EventIsStateBased | 1.3.6.1.4.1.1123.3.1.2.4.1.6.1.3 | INTEGER | read-only | The value of this attribute determined whether the Event being reported is a state-based Event or not. If the value of this attribute is TRUE then the Event is state-based. Else the Event is not state-based |
| NUM a6EventStateKey | 1.3.6.1.4.1.1123.3.1.2.4.1.6.1.4 | DmiInteger | read-only | This attribute holds the key identifying a row of the Event State group within the Component in which the event generator group is located. The Current State attribute within the row contains the current state of this state-based event. The current state can be one of the four severities: OK, Non-Critical, Critical, and Non-Recoverable. |
| STR a6AssociatedGroup | 1.3.6.1.4.1.1123.3.1.2.4.1.6.1.5 | DmiDisplaystring | read-only | The |
| INT a6EventSystem | 1.3.6.1.4.1.1123.3.1.2.4.1.6.1.6 | INTEGER | read-only | The major functional aspect of the product causing the fault. |
| INT a6EventSubsystem | 1.3.6.1.4.1.1123.3.1.2.4.1.6.1.7 | INTEGER | read-only | The minor functional aspect of the product causing the fault. |
| tStorageController | 1.3.6.1.4.1.1123.3.1.2.4.1.7 | not-accessible | This group defines the storage controller in this system. | |
| eStorageController | 1.3.6.1.4.1.1123.3.1.2.4.1.7.1 | not-accessible | ||
| NUM a7ControllerIndex | 1.3.6.1.4.1.1123.3.1.2.4.1.7.1.1 | DmiInteger | read-only | An index into the Storage Controller table. |
| STR a7Identification | 1.3.6.1.4.1.1123.3.1.2.4.1.7.1.2 | DmiDisplaystring | read-only | e.g. Name, brand and hardware revision level of the storage controller. |
| INT a7WorldwideIdentifierType | 1.3.6.1.4.1.1123.3.1.2.4.1.7.1.3 | INTEGER | read-only | The type of identifier displayed by the Worldwide Identifier attribute. |
| STR a7WorldwideIdentifier | 1.3.6.1.4.1.1123.3.1.2.4.1.7.1.4 | DmiDisplaystring | read-only | The Worldwide identifier for this controller. |
| INT a7ProtectionManagement | 1.3.6.1.4.1.1123.3.1.2.4.1.7.1.5 | INTEGER | read-only | Indicates whether or not the controller provides redundancy or protection against device failures. |
| INT a7BusMaster | 1.3.6.1.4.1.1123.3.1.2.4.1.7.1.6 | INTEGER | read-only | If true, then this storage controller is the bus master. |
| NUM a7SecondsSinceLastPower_up | 1.3.6.1.4.1.1123.3.1.2.4.1.7.1.7 | DmiInteger | read-only | The number of seconds that have passed since this controller was last powered on. |
| NUM a7FruGroupIndex | 1.3.6.1.4.1.1123.3.1.2.4.1.7.1.8 | DmiInteger | read-only | If this is a Field Replaceable Unit or if it is part of another FRU, this provides an index into the FRU table; 'value = -1' indicates that the group is not a FRU. |
| NUM a7OperationalGroupIndex | 1.3.6.1.4.1.1123.3.1.2.4.1.7.1.9 | DmiInteger | read-only | The index into the Operational State table for this device. |
| tStorageControllerEvents | 1.3.6.1.4.1.1123.3.1.2.4.1.8 | not-accessible | Storage Controller events. | |
| eStorageControllerEvents | 1.3.6.1.4.1.1123.3.1.2.4.1.8.1 | not-accessible | ||
| NTF trap5 | 1.3.6.1.4.1.1123.3.1.2.4.1.8.1.0.1 | Storage Controller Error | ||
| NTF trap6 | 1.3.6.1.4.1.1123.3.1.2.4.1.8.1.0.2 | Self-monitoring Warning | ||
| INT a8StorageControllerEventType | 1.3.6.1.4.1.1123.3.1.2.4.1.8.1.1 | INTEGER | read-only | The type of Storage Controller event that has occurred. |
| INT a8EventSeverity | 1.3.6.1.4.1.1123.3.1.2.4.1.8.1.2 | INTEGER | read-only | The severity of this event. |
| INT a8EventIsStateBased | 1.3.6.1.4.1.1123.3.1.2.4.1.8.1.3 | INTEGER | read-only | The value of this attribute determined whether the Event being reported is a state-based Event or not. If the value of this attribute is TRUE then the Event is state-based. Else the Event is not state-based |
| NUM a8EventStateKey | 1.3.6.1.4.1.1123.3.1.2.4.1.8.1.4 | DmiInteger | read-only | This attribute holds the key identifying a row of the Event State group within the Component in which the event generator group is located. The Current State attribute within the row contains the current state of this state-based event. The current state can be one of the four severities: OK, Non-Critical, Critical, and Non-Recoverable. |
| STR a8AssociatedGroup | 1.3.6.1.4.1.1123.3.1.2.4.1.8.1.5 | DmiDisplaystring | read-only | The |
| INT a8EventSystem | 1.3.6.1.4.1.1123.3.1.2.4.1.8.1.6 | INTEGER | read-only | The major functional aspect of the product causing the fault. |
| INT a8EventSubsystem | 1.3.6.1.4.1.1123.3.1.2.4.1.8.1.7 | INTEGER | read-only | The minor functional aspect of the product causing the fault. |
| tBusPort | 1.3.6.1.4.1.1123.3.1.2.4.1.9 | not-accessible | This global table has one entry for each of the Bus Ports in this Component. | |
| eBusPort | 1.3.6.1.4.1.1123.3.1.2.4.1.9.1 | not-accessible | ||
| NUM a9BusPortIndex | 1.3.6.1.4.1.1123.3.1.2.4.1.9.1.1 | DmiInteger | read-only | An index into the Bus Port table. |
| INT a9Protocol | 1.3.6.1.4.1.1123.3.1.2.4.1.9.1.2 | INTEGER | read-only | The protocol describing the electrical characteristic of the Bus Port. If 'Other' is used, then the Protocol Description attribute shall be used. |
| STR a9ProtocolDescription | 1.3.6.1.4.1.1123.3.1.2.4.1.9.1.3 | DmiDisplaystring | read-only | Additional description of the protocol described above. If 'Other' was specified above, then this field shall be used. Otherwise, the contents of this optional field shall not contradict the Protocol specified above. |
| INT a9SignalCharacteristics | 1.3.6.1.4.1.1123.3.1.2.4.1.9.1.4 | INTEGER | read-only | The signal characteristics of the Bus Port being described. |
| INT a9WorldwideIdentifierType | 1.3.6.1.4.1.1123.3.1.2.4.1.9.1.5 | INTEGER | read-only | The type of identifier displayed by the Worldwide Identifier attribute. |
| STR a9WorldwideIdentifier | 1.3.6.1.4.1.1123.3.1.2.4.1.9.1.6 | DmiDisplaystring | read-only | The Worldwide identifier for this bus port. |
| STR a9AddressDescriptor | 1.3.6.1.4.1.1123.3.1.2.4.1.9.1.7 | DmiDisplaystring | read-only | The address descriptor of this bus port. For example, the SCSI address of this port. |
| INT a9Isochronous | 1.3.6.1.4.1.1123.3.1.2.4.1.9.1.8 | INTEGER | read-only | Indicates whether or not this bus port supports isochronous transfers. |
| NUM a9MaximumWidth | 1.3.6.1.4.1.1123.3.1.2.4.1.9.1.9 | DmiInteger | read-only | The maximum width, in bits, of this Bus Port's data path. A value of 1 should be used for serial. |
| NUM a9MaximumTransferRate | 1.3.6.1.4.1.1123.3.1.2.4.1.9.1.10 | DmiInteger | read-only | The theoretical maximum transfer rate, in millions of bytes per second, that this Bus Port is capable of achieving under ideal conditions. A value of zero should be used if the transfer rate is less than 1 million bytes per second. A value of 0x80000000 should be used if the transfer rate is unknown. |
| NUM a9MaximumNumberOfAttachments | 1.3.6.1.4.1.1123.3.1.2.4.1.9.1.11 | DmiInteger | read-only | The maximum number of directly addressable entities supported by this bus port's protocol. A value of zero should be used if the number of attachments is unknown. |
| INT a9ConnectorType | 1.3.6.1.4.1.1123.3.1.2.4.1.9.1.12 | INTEGER | read-only | Describes how options (cards, devices, etc.) physically connect to this bus port. If 'Other' is used, then the Connector Type Description attribute shall be used. |
| STR a9ConnectorTypeDescription | 1.3.6.1.4.1.1123.3.1.2.4.1.9.1.13 | DmiDisplaystring | read-only | An additional text description of the type of connector describe above. If 'Other' was specified above, then this field shall be used. Otherwis , the contents of this optional field shall not contradict the connector specified above. |
| INT a9ConnectorGender | 1.3.6.1.4.1.1123.3.1.2.4.1.9.1.14 | INTEGER | read-only | Indicates the gender of the connector described above. |
| NUM a9OperationalGroupIndex | 1.3.6.1.4.1.1123.3.1.2.4.1.9.1.15 | DmiInteger | read-only | The index into the Operational State table for this bus port. |
| NUM a9MassStorageStatisticsGroupIndex | 1.3.6.1.4.1.1123.3.1.2.4.1.9.1.16 | DmiInteger | read-only | The index into the Mass Storage Statistics table for this bus port. |
| tBusPortEvents | 1.3.6.1.4.1.1123.3.1.2.4.1.10 | not-accessible | Bus Port events. | |
| eBusPortEvents | 1.3.6.1.4.1.1123.3.1.2.4.1.10.1 | not-accessible | ||
| INT a10BusPortEventType | 1.3.6.1.4.1.1123.3.1.2.4.1.10.1.1 | INTEGER | read-only | The type of Bus Port event that has occurred. |
| INT a10EventSeverity | 1.3.6.1.4.1.1123.3.1.2.4.1.10.1.2 | INTEGER | read-only | The severity of this event. |
| INT a10EventIsStateBased | 1.3.6.1.4.1.1123.3.1.2.4.1.10.1.3 | INTEGER | read-only | The value of this attribute determined whether the Event being reported is a state-based Event or not. If the value of this attribute is TRUE then the Event is state-based. Else the Event is not state-based |
| NUM a10EventStateKey | 1.3.6.1.4.1.1123.3.1.2.4.1.10.1.4 | DmiInteger | read-only | This attribute holds the key identifying a row of the Event State group within the Component in which the event generator group is located. The Current State attribute within the row contains the current state of this state-based event. The current state can be one of the four severities: OK, Non-Critical, Critical, and Non-Recoverable. |
| STR a10AssociatedGroup | 1.3.6.1.4.1.1123.3.1.2.4.1.10.1.5 | DmiDisplaystring | read-only | The |
| INT a10EventSystem | 1.3.6.1.4.1.1123.3.1.2.4.1.10.1.6 | INTEGER | read-only | The major functional aspect of the product causing the fault. |
| INT a10EventSubsystem | 1.3.6.1.4.1.1123.3.1.2.4.1.10.1.7 | INTEGER | read-only | The minor functional aspect of the product causing the fault. |
| tMassStorageAssociation | 1.3.6.1.4.1.1123.3.1.2.4.1.11 | not-accessible | Mass storage associations define the relationships between the various components of the Storage Subsystem. | |
| eMassStorageAssociation | 1.3.6.1.4.1.1123.3.1.2.4.1.11.1 | not-accessible | ||
| NUM a11AssociationIndex | 1.3.6.1.4.1.1123.3.1.2.4.1.11.1.1 | DmiInteger | read-only | An index into the Association table. |
| INT a11Type | 1.3.6.1.4.1.1123.3.1.2.4.1.11.1.2 | INTEGER | read-only | This field specifies the type of the association. |
| INT a11Object1Type | 1.3.6.1.4.1.1123.3.1.2.4.1.11.1.3 | INTEGER | read-only | This field specifies the type of the object referred to by object 1 index. Therefore, combined with the object 1 index a complete referenc is made to a specific object. |
| NUM a11Object1Index | 1.3.6.1.4.1.1123.3.1.2.4.1.11.1.4 | DmiInteger | read-only | An index into the table identified by the object 1 type. |
| INT a11Object2Type | 1.3.6.1.4.1.1123.3.1.2.4.1.11.1.5 | INTEGER | read-only | This field specifies the type of the object referred to by object 2 index. Therefore, combined with the object 2 index a complete referenc is made to a specific object. |
| NUM a11Object2Index | 1.3.6.1.4.1.1123.3.1.2.4.1.11.1.6 | DmiInteger | read-only | An index into the table identified by the Object 2 type. |
| tMassStorageAssociationEvents | 1.3.6.1.4.1.1123.3.1.2.4.1.12 | not-accessible | Mass Storage Association events. | |
| eMassStorageAssociationEvents | 1.3.6.1.4.1.1123.3.1.2.4.1.12.1 | not-accessible | ||
| INT a12MassStorageAssociationEventType | 1.3.6.1.4.1.1123.3.1.2.4.1.12.1.1 | INTEGER | read-only | The type of Mass storage association where a change has occurred |
| INT a12EventSeverity | 1.3.6.1.4.1.1123.3.1.2.4.1.12.1.2 | INTEGER | read-only | The severity of this event. |
| INT a12EventIsStateBased | 1.3.6.1.4.1.1123.3.1.2.4.1.12.1.3 | INTEGER | read-only | The value of this attribute determined whether the Event being reported is a state-based Event or not. If the value of this attribute is TRUE then the Event is state-based. Else the Event is not state-based |
| NUM a12EventStateKey | 1.3.6.1.4.1.1123.3.1.2.4.1.12.1.4 | DmiInteger | read-only | This attribute holds the key identifying a row of the Event State group within the Component in which the event generator group is located. The Current State attribute within the row contains the current state of this state-based event. The current state can be one of the four severities: OK, Non-Critical, Critical, and Non-Recoverable. |
| STR a12AssociatedGroup | 1.3.6.1.4.1.1123.3.1.2.4.1.12.1.5 | DmiDisplaystring | read-only | The |
| INT a12EventSystem | 1.3.6.1.4.1.1123.3.1.2.4.1.12.1.6 | INTEGER | read-only | The mass storage association object type which is causing a change. |
| INT a12EventSubsystem | 1.3.6.1.4.1.1123.3.1.2.4.1.12.1.7 | INTEGER | read-only | The minor functional aspect of the product causing the fault. |
| tBusPortAssociation | 1.3.6.1.4.1.1123.3.1.2.4.1.13 | not-accessible | Bus Port Association | |
| eBusPortAssociation | 1.3.6.1.4.1.1123.3.1.2.4.1.13.1 | not-accessible | ||
| NUM a13BusPortAssociationIndex | 1.3.6.1.4.1.1123.3.1.2.4.1.13.1.1 | DmiInteger | read-only | An index into the Bus Port Association table. This index is the same as the index in the Association group that defines the bus port association. |
| NUM a13NegotiatedSpeed | 1.3.6.1.4.1.1123.3.1.2.4.1.13.1.2 | DmiInteger | read-only | The maximum burst transfer rate, in millions of bytes, which was negotiated between the two associated bus ports. |
| NUM a13NegotiatedWidth | 1.3.6.1.4.1.1123.3.1.2.4.1.13.1.3 | DmiInteger | read-only | The width, in bits, of the bus ports data path which was negotiated between the two associated bus ports. |
| tOperationalState | 1.3.6.1.4.1.1123.3.1.2.4.1.14 | not-accessible | This group provides the operational state, usage, and availabili y status, and administrative state indicators for specific Device Group instance . | |
| eOperationalState | 1.3.6.1.4.1.1123.3.1.2.4.1.14.1 | not-accessible | ||
| NUM a14OperationalStateInstanceIndex | 1.3.6.1.4.1.1123.3.1.2.4.1.14.1.1 | DmiInteger | read-only | The Index into the Operational State table. |
| NUM a14DeviceGroupIndex | 1.3.6.1.4.1.1123.3.1.2.4.1.14.1.2 | DmiInteger | read-only | The group ID of the group referencing this instance. |
| INT a14OperationalStatus | 1.3.6.1.4.1.1123.3.1.2.4.1.14.1.3 | INTEGER | read-only | The operational status of the Device Group instance. |
| INT a14UsageState | 1.3.6.1.4.1.1123.3.1.2.4.1.14.1.4 | INTEGER | read-only | The usage state of the Device Group instance. |
| INT a14AvailabilityStatus | 1.3.6.1.4.1.1123.3.1.2.4.1.14.1.5 | INTEGER | read-only | The availability status of the Device Group instance. |
| INT a14AdministrativeState | 1.3.6.1.4.1.1123.3.1.2.4.1.14.1.6 | INTEGER | read-only | The administrative state of the Device Group instance. |
| NUM a14FatalErrorCount | 1.3.6.1.4.1.1123.3.1.2.4.1.14.1.7 | DmiCounter | read-only | The accumulated Fatal or Non-recoverable error count for this Device Group instance. |
| NUM a14MajorErrorCount | 1.3.6.1.4.1.1123.3.1.2.4.1.14.1.8 | DmiCounter | read-only | The accumulated Major or Critical error count for this Device Group instance. |
| NUM a14WarningErrorCount | 1.3.6.1.4.1.1123.3.1.2.4.1.14.1.9 | DmiCounter | read-only | The accumulated Warning or Non-Critical error count for this Device Group instance. |
| INT a14CurrentErrorStatus | 1.3.6.1.4.1.1123.3.1.2.4.1.14.1.10 | INTEGER | read-only | This attribute presents the current error status for this Device Group instance. The most critical error status in effect should be presented. I.e. if a part of the Device Group instance is 'Critical', while other status is 'Non-critical' then the status 'Critical' should be reported. |
| INT a14DevicePredictedFailureStatus | 1.3.6.1.4.1.1123.3.1.2.4.1.14.1.11 | INTEGER | read-only | Enumeration describing the current Device Predicted Failure Status (e.g.: the S.M.A.R.T. status of the device). |
| tSymsdmsmassstoragesystem | 1.3.6.1.4.1.1123.3.1.2.4.1.15 | not-accessible | This group is the Symbios Vendor unique group. | |
| eSymsdmsmassstoragesystem | 1.3.6.1.4.1.1123.3.1.2.4.1.15.1 | not-accessible | ||
| NUM a15SymDeviceIndex | 1.3.6.1.4.1.1123.3.1.2.4.1.15.1.1 | DmiInteger | read-only | An index into the Symbios Vendor Unique Device info table. |
| NUM a15SymDeviceFlag | 1.3.6.1.4.1.1123.3.1.2.4.1.15.1.2 | DmiInteger | read-only | An Symbios Vendor Unique Flag. |
| INT a15SmartReportingCapability | 1.3.6.1.4.1.1123.3.1.2.4.1.15.1.3 | INTEGER | read-write | A flag indicating the state of a Devices's SMART reporting capability. |
| NUM a15SmartPollingPeriod | 1.3.6.1.4.1.1123.3.1.2.4.1.15.1.4 | DmiInteger | read-write | Number of minutes to wait between polling a device for its S.M.A.R.T. status. |
| tMiftomib | 1.3.6.1.4.1.1123.3.1.2.4.1.99 | not-accessible | This group defines attributes required for DMI to SNMP translati n. | |
| eMiftomib | 1.3.6.1.4.1.1123.3.1.2.4.1.99.1 | not-accessible | ||
| STR a99MibName | 1.3.6.1.4.1.1123.3.1.2.4.1.99.1.1 | DmiDisplaystring | read-only | The MIB name that defines this MIF |
| STR a99MibOid | 1.3.6.1.4.1.1123.3.1.2.4.1.99.1.2 | DmiDisplaystring | read-only | The MIB OID that corresponds to this MIF |
| NUM a99DisableTrap | 1.3.6.1.4.1.1123.3.1.2.4.1.99.1.3 | DmiInteger | read-write | This attribute can be changed to disable sending oftraps from this component |
RFC description
Symbios Logic SCSI mass storage subsystem MIB for disk array monitoring.
Start monitoring Symbios/LSI Logic SCSI host bus adapter/RAID controller, legacy mass storage (hardware/firmware inventory) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.