SYMBIOSDMI20MIFDEFINITIONID22-MIB

All MIBs › SYMBIOSDMI20MIFDEFINITIONID22-MIB

Category: Legacy and Historical, Storage

Description: Defines Symbios DMI 2.0 component ID 2.2 instrumentation objects for legacy storage controller management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SYMBIOSDMI20MIFDEFINITIONID22-MIB?

SYMBIOSDMI20MIFDEFINITIONID22-MIB is a legacy module translating a Symbios (later LSI Logic) DMI 2.0 MIF (Management Information Format) component definition into SNMP form, used for instrumenting SCSI storage controller hardware inventory. It exposes component/subcomponent identity data such as manufacturer, product name, version, and serial number, plus installation and verification status, and subcomponent software index/version. Its monitoring role is mostly hardware/software inventory and installation-status rather than live performance counters: confirming a SCSI controller component's identity, that it installed successfully (a1Installation), and passed verification (a1Verify), and which software/firmware version its subcomponents report. It is directly derived from the DMI 2.0 MIF standard and tied to SCSI conventions (scsi, cosprings namespace) from that era. It is deployed on legacy servers or storage systems using Symbios/LSI SCSI controllers managed via DMI-to-SNMP bridging. Engineers can download the SYMBIOSDMI20MIFDEFINITIONID22-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SYMBIOSDMI20MIFDEFINITIONID22-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Symbios/LSI legacy SCSI storage controller

Monitoring Examples

An admin checks a1Manufacturer, a1Product, and a1Version to confirm the identity and firmware version of an installed SCSI controller component, and reviews a1Installation and a1Verify to confirm the component was installed and passed its self-verification. A failed a1Verify status alongside an unexpected a1SerialNumber would indicate a controller was swapped or is misconfigured following a hardware replacement.

What Can Be Monitored

component manufacturer/product/version
component serial number
installation status
verification status
subcomponent software version

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
symbios	1.3.6.1.4.1.1123
cosprings	1.3.6.1.4.1.1123.3
scsi	1.3.6.1.4.1.1123.3.1
fam8xx	1.3.6.1.4.1.1123.3.1.2
id22	1.3.6.1.4.1.1123.3.1.2.22
dmtfGroups	1.3.6.1.4.1.1123.3.1.2.22.1
tComponentid	1.3.6.1.4.1.1123.3.1.2.22.1.1		not-accessible	This group defines the attributes common to all components. This group is required.
eComponentid	1.3.6.1.4.1.1123.3.1.2.22.1.1.1		not-accessible
STR a1Manufacturer	1.3.6.1.4.1.1123.3.1.2.22.1.1.1.1	DmiDisplaystring	read-only	Manufacturer of this component.
STR a1Product	1.3.6.1.4.1.1123.3.1.2.22.1.1.1.2	DmiDisplaystring	read-only	Product name for this component.
STR a1Version	1.3.6.1.4.1.1123.3.1.2.22.1.1.1.3	DmiDisplaystring	read-only	Version number of this component.
STR a1SerialNumber	1.3.6.1.4.1.1123.3.1.2.22.1.1.1.4	DmiDisplaystring	read-only	Serial number for this component
DMI a1Installation	1.3.6.1.4.1.1123.3.1.2.22.1.1.1.5	DmiDateX	read-only	The installation date and time of this component. The Service Layer assigns this value, the manufacturer should leave it blank.
INT a1Verify	1.3.6.1.4.1.1123.3.1.2.22.1.1.1.6	INTEGER	read-only	A code that provides a level of verification that the component is still installed and working.
tSubcomponentSoftware	1.3.6.1.4.1.1123.3.1.2.22.1.2		not-accessible	This group describes the software resources that are used by a component or subcomponent.
eSubcomponentSoftware	1.3.6.1.4.1.1123.3.1.2.22.1.2.1		not-accessible
NUM a2SoftwareIndex	1.3.6.1.4.1.1123.3.1.2.22.1.2.1.1	DmiInteger	read-only	An index into the SubComponent Software table
STR a2Type	1.3.6.1.4.1.1123.3.1.2.22.1.2.1.2	DmiDisplaystring	read-only	The type of software resource described by this row. For example this value would be 'Device Driver', 'INF File', 'Boot ROM', and etc.
STR a2Vendor	1.3.6.1.4.1.1123.3.1.2.22.1.2.1.3	DmiDisplaystring	read-only	The name of the vendor who supplied this piece of software.
STR a2Version	1.3.6.1.4.1.1123.3.1.2.22.1.2.1.4	DmiDisplaystring	read-only	The revision level of this piece of software. For example the Version Major, Version Minor, Revision, and Build numbers.
STR a2Description	1.3.6.1.4.1.1123.3.1.2.22.1.2.1.5	DmiDisplaystring	read-only	An additional description of this piece of software
STR a2IdentificationCode	1.3.6.1.4.1.1123.3.1.2.22.1.2.1.6	DmiDisplaystring	read-only	The Stock Keeping Unit (SKU) or Part Number for this piece of software.
STR a2LanguageEdition	1.3.6.1.4.1.1123.3.1.2.22.1.2.1.7	DmiDisplaystring	read-only	Identifies the language edition of this piece of software.
STR a2InterfaceDescription	1.3.6.1.4.1.1123.3.1.2.22.1.2.1.8	DmiDisplaystring	read-only	This is the specification or operating system to which this piece of software conforms. (e.g. 'Microsoft NT', 'NetWare', etc.)
STR a2InterfaceVersion	1.3.6.1.4.1.1123.3.1.2.22.1.2.1.9	DmiDisplaystring	read-only	The specification or operating system version to which this piece of software conforms. (e.g. '4.0 or higher', '3.xx', etc.)
tWorldwideIdentifer	1.3.6.1.4.1.1123.3.1.2.22.1.3		not-accessible	The Worldwide Identifer
eWorldwideIdentifer	1.3.6.1.4.1.1123.3.1.2.22.1.3.1		not-accessible
NUM a3WorldwideIdentifierIndex	1.3.6.1.4.1.1123.3.1.2.22.1.3.1.1	DmiInteger	read-only	An index into the Worldwide Identifier table.
INT a3WorldwideIdentifierType	1.3.6.1.4.1.1123.3.1.2.22.1.3.1.2	INTEGER	read-only	The type of identifier displayed by the Worldwide Identifier attribute.
STR a3WorldwideIdentifier	1.3.6.1.4.1.1123.3.1.2.22.1.3.1.3	DmiDisplaystring	read-only	The Worldwide identifier for this device.
tFieldReplaceableUnit	1.3.6.1.4.1.1123.3.1.2.22.1.4		not-accessible	A Field Replaceable Unit (FRU), is defined as a hardware component which is designed to be separately removable for replacement or repair. For the purposes of this definition, a motherboard and a fixed hard disk are FRUs, whereas a fixed hard disk platter or a chip fixed in place on the motherboard are not FRUs since they are not designed to be separately removable. Each instance within the FRU table should contain the device group and instance data for the associated hardware component.
eFieldReplaceableUnit	1.3.6.1.4.1.1123.3.1.2.22.1.4.1		not-accessible
NUM a4FruIndex	1.3.6.1.4.1.1123.3.1.2.22.1.4.1.1	DmiInteger	read-only	The index into the Field Replaceable Unit table.
NUM a4DeviceGroupIndex	1.3.6.1.4.1.1123.3.1.2.22.1.4.1.2	DmiInteger	read-only	The group ID of the group referencing this Field Replaceable Unit instance.
STR a4Description	1.3.6.1.4.1.1123.3.1.2.22.1.4.1.3	DmiDisplaystring	read-only	A clear description of this Field Replaceable Unit.
STR a4Manufacturer	1.3.6.1.4.1.1123.3.1.2.22.1.4.1.4	DmiDisplaystring	read-only	The name of the company manufacturing or providing this Field Replaceable Unit.
STR a4Model	1.3.6.1.4.1.1123.3.1.2.22.1.4.1.5	DmiDisplaystring	read-only	The manufacturer's model number for this Field Replaceable Unit.
STR a4PartNumber	1.3.6.1.4.1.1123.3.1.2.22.1.4.1.6	DmiDisplaystring	read-only	A part number by which a replacement part can be ordered for this Field Replaceable Unit.
STR a4FruSerialNumber	1.3.6.1.4.1.1123.3.1.2.22.1.4.1.7	DmiDisplaystring	read-only	The manufacturer's serial number for this Field Replaceable Unit.
STR a4RevisionLevel	1.3.6.1.4.1.1123.3.1.2.22.1.4.1.8	DmiDisplaystring	read-only	The revision level of this Field Replaceable Unit.
DMI a4WarrantyStartDate	1.3.6.1.4.1.1123.3.1.2.22.1.4.1.9	DmiDateX	read-only	The start date of the service warranty for this Field Replaceabl Unit.
NUM a4WarrantyDuration	1.3.6.1.4.1.1123.3.1.2.22.1.4.1.10	DmiInteger	read-only	The total duration of this Field Replaceable Unit warranty in months.
STR a4SupportPhoneNumber	1.3.6.1.4.1.1123.3.1.2.22.1.4.1.11	DmiDisplaystring	read-only	The phone number(s) for support for this Field Replaceable Unit.
STR a4FruInternetUniformResourceLocator	1.3.6.1.4.1.1123.3.1.2.22.1.4.1.12	DmiDisplaystring	read-only	The Internet Uniform Resource Locator string that can be used through a World Wide Web browser to obtain further information about this FRU
tStorageDevices	1.3.6.1.4.1.1123.3.1.2.22.1.5		not-accessible	This group defines the mass storage devices in this system.
eStorageDevices	1.3.6.1.4.1.1123.3.1.2.22.1.5.1		not-accessible
NUM a5StorageDeviceIndex	1.3.6.1.4.1.1123.3.1.2.22.1.5.1.1	DmiInteger	read-only	An index into the storage device table.
INT a5Type	1.3.6.1.4.1.1123.3.1.2.22.1.5.1.2	INTEGER	read-only	The type of this mass storage device. If 'Other' is used, then the Type Description attribute shall be used.
STR a5TypeDescription	1.3.6.1.4.1.1123.3.1.2.22.1.5.1.3	DmiDisplaystring	read-only	A longer description of the storage device. For example: 3.5 inch flexible diskette drive using diskettes with a maximum capacity of 1.44MB. If 'Other' was specified above, then this field shall be used. Otherwise, the contents of this optional field shall not contradict the Storage Device Type specified above.
STR a5Sub_identifier	1.3.6.1.4.1.1123.3.1.2.22.1.5.1.4	DmiDisplaystring	read-only	The sub-identifier for this storage device (e.g., the device's SCSI logical unit number).
NUM a5MediaDataBlockSize	1.3.6.1.4.1.1123.3.1.2.22.1.5.1.5	DmiInteger	read-only	The size in bytes of the data blocks used on the storage media. If the media block size is unknown or not consistent across the media, then this value shall be zero.
NUM a5FormattedMediaCapacity	1.3.6.1.4.1.1123.3.1.2.22.1.5.1.6	DmiInteger64X	read-only	The total size in bytes of this storage media after it has been formatted.
INT a5RemovableDevice	1.3.6.1.4.1.1123.3.1.2.22.1.5.1.7	INTEGER	read-only	If true, then this storage device is removable (e.g.: PCMCIA device).
INT a5DeviceLoaded	1.3.6.1.4.1.1123.3.1.2.22.1.5.1.8	INTEGER	read-only	If true, then the storage device is loaded. If the device is not removable, then this value shall be 'TRUE'.
INT a5RemovableMedia	1.3.6.1.4.1.1123.3.1.2.22.1.5.1.9	INTEGER	read-only	If true, then the media in this storage device is removable.
INT a5MediaLoaded	1.3.6.1.4.1.1123.3.1.2.22.1.5.1.10	INTEGER	read-only	If true, the media in this storage device is loaded. If the media is not removable, then this value shall be 'TRUE'
INT a5Compression	1.3.6.1.4.1.1123.3.1.2.22.1.5.1.11	INTEGER	read-only	If true, the storage device supports compression.
INT a5Encryption	1.3.6.1.4.1.1123.3.1.2.22.1.5.1.12	INTEGER	read-only	If true, the storage device supports encryption.
tStorageDevicesEvents	1.3.6.1.4.1.1123.3.1.2.22.1.6		not-accessible	Storage Devices events.
eStorageDevicesEvents	1.3.6.1.4.1.1123.3.1.2.22.1.6.1		not-accessible
NTF trap1forStorageDevices	1.3.6.1.4.1.1123.3.1.2.22.1.6.1.0.1			Self-Monitoring Warning (predictive failure - data recovery possible)
NTF trap2forStorageDevices	1.3.6.1.4.1.1123.3.1.2.22.1.6.1.0.2			Self-Monitoring Warning (predictive failure - data recovery questionable)
INT a6StorageDevicesEventType	1.3.6.1.4.1.1123.3.1.2.22.1.6.1.1	INTEGER	read-only	The type of Storage Devices event that has occurred.
INT a6EventSeverity	1.3.6.1.4.1.1123.3.1.2.22.1.6.1.2	INTEGER	read-only	The severity of this event.
INT a6EventIsStateBased	1.3.6.1.4.1.1123.3.1.2.22.1.6.1.3	INTEGER	read-only	The value of this attribute determined whether the Event being reported is a state-based Event or not. If the value of this attribute is TRUE then the Event is state-based. Else the Event is not state-based
NUM a6EventStateKey	1.3.6.1.4.1.1123.3.1.2.22.1.6.1.4	DmiInteger	read-only	This attribute holds the key identifying a row of the Event State group within the Component in which the event generator group is located. The Current State attribute within the row contains the current state of this state-based event. The current state can be one of the four severities: OK, Non-Critical, Critical, and Non-Recoverable.
STR a6AssociatedGroup	1.3.6.1.4.1.1123.3.1.2.22.1.6.1.5	DmiDisplaystring	read-only	The
INT a6EventSystem	1.3.6.1.4.1.1123.3.1.2.22.1.6.1.6	INTEGER	read-only	The major functional aspect of the product causing the fault.
INT a6EventSubsystem	1.3.6.1.4.1.1123.3.1.2.22.1.6.1.7	INTEGER	read-only	The minor functional aspect of the product causing the fault.
INT a6EventSolution	1.3.6.1.4.1.1123.3.1.2.22.1.6.1.8	INTEGER	read-only	A solution to the problem that caused the event.
INT a6InstanceDataPresent	1.3.6.1.4.1.1123.3.1.2.22.1.6.1.9	INTEGER	read-only	Indicates whether the second event block contains instance-speci ic data.
STR a6EventMessage	1.3.6.1.4.1.1123.3.1.2.22.1.6.1.10	DmiDisplaystring	read-only	Auxiliary information related to the event.
tStorageController	1.3.6.1.4.1.1123.3.1.2.22.1.7		not-accessible	This group defines the storage controller in this system.
eStorageController	1.3.6.1.4.1.1123.3.1.2.22.1.7.1		not-accessible
NUM a7ControllerIndex	1.3.6.1.4.1.1123.3.1.2.22.1.7.1.1	DmiInteger	read-only	An index into the Storage Controller table.
STR a7Identification	1.3.6.1.4.1.1123.3.1.2.22.1.7.1.2	DmiDisplaystring	read-only	e.g. Name, brand and hardware revision level of the storage controller.
INT a7ProtectionManagement	1.3.6.1.4.1.1123.3.1.2.22.1.7.1.3	INTEGER	read-only	Indicates whether or not the controller provides redundancy or protection against device failures.
INT a7BusMaster	1.3.6.1.4.1.1123.3.1.2.22.1.7.1.4	INTEGER	read-only	If true, then this storage controller is the bus master.
NUM a7SecondsSinceLastPower_up	1.3.6.1.4.1.1123.3.1.2.22.1.7.1.5	DmiInteger	read-only	The number of seconds that have passed since this controller was last powered on.
tStorageControllerEvents	1.3.6.1.4.1.1123.3.1.2.22.1.8		not-accessible	Storage Controller events.
eStorageControllerEvents	1.3.6.1.4.1.1123.3.1.2.22.1.8.1		not-accessible
NTF trap3forStorageController	1.3.6.1.4.1.1123.3.1.2.22.1.8.1.0.3			Storage Controller Error (not responding)
INT a8StorageControllerEventType	1.3.6.1.4.1.1123.3.1.2.22.1.8.1.1	INTEGER	read-only	The type of Storage Controller event that has occurred.
INT a8EventSeverity	1.3.6.1.4.1.1123.3.1.2.22.1.8.1.2	INTEGER	read-only	The severity of this event.
INT a8EventIsStateBased	1.3.6.1.4.1.1123.3.1.2.22.1.8.1.3	INTEGER	read-only	The value of this attribute determined whether the Event being reported is a state-based Event or not. If the value of this attribute is TRUE then the Event is state-based. Else the Event is not state-based
NUM a8EventStateKey	1.3.6.1.4.1.1123.3.1.2.22.1.8.1.4	DmiInteger	read-only	This attribute holds the key identifying a row of the Event State group within the Component in which the event generator group is located. The Current State attribute within the row contains the current state of this state-based event. The current state can be one of the four severities: OK, Non-Critical, Critical, and Non-Recoverable.
STR a8AssociatedGroup	1.3.6.1.4.1.1123.3.1.2.22.1.8.1.5	DmiDisplaystring	read-only	The
INT a8EventSystem	1.3.6.1.4.1.1123.3.1.2.22.1.8.1.6	INTEGER	read-only	The major functional aspect of the product causing the fault.
INT a8EventSubsystem	1.3.6.1.4.1.1123.3.1.2.22.1.8.1.7	INTEGER	read-only	The minor functional aspect of the product causing the fault.
INT a8EventSolution	1.3.6.1.4.1.1123.3.1.2.22.1.8.1.8	INTEGER	read-only	A solution to the problem that caused the event.
INT a8InstanceDataPresent	1.3.6.1.4.1.1123.3.1.2.22.1.8.1.9	INTEGER	read-only	Indicates whether the second event block contains instance-speci ic data.
STR a8EventMessage	1.3.6.1.4.1.1123.3.1.2.22.1.8.1.10	DmiDisplaystring	read-only	Auxiliary information related to the event.
tBusPort	1.3.6.1.4.1.1123.3.1.2.22.1.9		not-accessible	This global table has one entry for each of the Bus Ports in this Component.
eBusPort	1.3.6.1.4.1.1123.3.1.2.22.1.9.1		not-accessible
NUM a9BusPortIndex	1.3.6.1.4.1.1123.3.1.2.22.1.9.1.1	DmiInteger	read-only	An index into the Bus Port table.
INT a9Protocol	1.3.6.1.4.1.1123.3.1.2.22.1.9.1.2	INTEGER	read-only	The protocol describing the electrical characteristic of the Bus Port. If 'Other' is used, then the Protocol Description attribute shall be used.
STR a9ProtocolDescription	1.3.6.1.4.1.1123.3.1.2.22.1.9.1.3	DmiDisplaystring	read-only	Additional description of the protocol described above. If 'Other' was specified above, then this field shall be used. Otherwise, the contents of this optional field shall not contradict the Protocol specified above.
INT a9SignalCharacteristics	1.3.6.1.4.1.1123.3.1.2.22.1.9.1.4	INTEGER	read-only	The signal characteristics of the Bus Port being described.
STR a9AddressDescriptor	1.3.6.1.4.1.1123.3.1.2.22.1.9.1.5	DmiDisplaystring	read-only	The address descriptor of this bus port. For example, the SCSI address of this port.
INT a9Isochronous	1.3.6.1.4.1.1123.3.1.2.22.1.9.1.6	INTEGER	read-only	Indicates whether or not this bus port supports isochronous transfers.
NUM a9MaximumWidth	1.3.6.1.4.1.1123.3.1.2.22.1.9.1.7	DmiInteger	read-only	The maximum width, in bits, of this Bus Port's data path. A value of 1 should be used for serial.
NUM a9MaximumTransferRate	1.3.6.1.4.1.1123.3.1.2.22.1.9.1.8	DmiInteger	read-only	The theoretical maximum transfer rate, in millions of bytes per second, that this Bus Port is capable of achieving under ideal conditions. A value of zero should be used if the transfer rate is less than 1 million bytes per second. A value of 0x80000000 should be used if the transfer rate is unknown.
NUM a9MaximumNumberOfAttachments	1.3.6.1.4.1.1123.3.1.2.22.1.9.1.9	DmiInteger	read-only	The maximum number of directly addressable entities supported by this bus port's protocol. A value of zero should be used if the number of attachments is unknown.
INT a9ConnectorType	1.3.6.1.4.1.1123.3.1.2.22.1.9.1.10	INTEGER	read-only	Describes how options (cards, devices, etc.) physically connect to this bus port. If 'Other' is used, then the Connector Type Description attribute shall be used.
STR a9ConnectorTypeDescription	1.3.6.1.4.1.1123.3.1.2.22.1.9.1.11	DmiDisplaystring	read-only	An additional text description of the type of connector describe above. If 'Other' was specified above, then this field shall be used. Otherwis , the contents of this optional field shall not contradict the connector specified above.
INT a9ConnectorGender	1.3.6.1.4.1.1123.3.1.2.22.1.9.1.12	INTEGER	read-only	Indicates the gender of the connector described above.
tFibreChannelBusPortExtensions	1.3.6.1.4.1.1123.3.1.2.22.1.10		not-accessible	This group extents the Bus Port group with Fibre Channel specific attributes.
eFibreChannelBusPortExtensions	1.3.6.1.4.1.1123.3.1.2.22.1.10.1		not-accessible
NUM a10BusPortIndex	1.3.6.1.4.1.1123.3.1.2.22.1.10.1.1	DmiInteger	read-only	The index into the Bus Port Table that this Fibre Channel group is extending.
NUM a10EndToEndCredit	1.3.6.1.4.1.1123.3.1.2.22.1.10.1.2	DmiInteger	read-only	The number of allowable outstanding acknowledgments for a sequence.
NUM a10BufferToBufferCredit	1.3.6.1.4.1.1123.3.1.2.22.1.10.1.3	DmiInteger	read-only	The number of frames which can be handled by the node before a wait for the buffer ready is required, and prior to subsequent frame transmiss ons.
INT a10LinkType	1.3.6.1.4.1.1123.3.1.2.22.1.10.1.4	INTEGER	read-only	Reports whether copper or fibre media is used.
INT a10FlowControlClassType	1.3.6.1.4.1.1123.3.1.2.22.1.10.1.5	INTEGER	read-only	Identifies the Flow Control Class Type.
INT a10FlowControlAcknowledgmentType	1.3.6.1.4.1.1123.3.1.2.22.1.10.1.6	INTEGER	read-only	Identifies the Flow Control Acknowledgment Type.
INT a10FabricTopology	1.3.6.1.4.1.1123.3.1.2.22.1.10.1.7	INTEGER	read-only	If true, a fabric topology exists within the fibre channel bus port.
tMassStorageAssociation	1.3.6.1.4.1.1123.3.1.2.22.1.11		not-accessible	Mass storage associations define the relationships between the various components of the Storage Subsystem.
eMassStorageAssociation	1.3.6.1.4.1.1123.3.1.2.22.1.11.1		not-accessible
NUM a11AssociationIndex	1.3.6.1.4.1.1123.3.1.2.22.1.11.1.1	DmiInteger	read-only	An index into the Association table.
STR a11Type	1.3.6.1.4.1.1123.3.1.2.22.1.11.1.2	DmiDisplaystring	read-only	This field specifies the type of the association.
STR a11Reference1	1.3.6.1.4.1.1123.3.1.2.22.1.11.1.3	DmiDisplaystring	read-only	A reference to an object.
STR a11Reference2	1.3.6.1.4.1.1123.3.1.2.22.1.11.1.4	DmiDisplaystring	read-only	A reference to an object.
tMassStorageAssociationEvents	1.3.6.1.4.1.1123.3.1.2.22.1.12		not-accessible	Mass Storage Association events.
eMassStorageAssociationEvents	1.3.6.1.4.1.1123.3.1.2.22.1.12.1		not-accessible
NTF trap4forMassStorageAssociation	1.3.6.1.4.1.1123.3.1.2.22.1.12.1.0.4			New Storage controller detected
NTF trap5forMassStorageAssociation	1.3.6.1.4.1.1123.3.1.2.22.1.12.1.0.5			New device detected
NTF trap6forMassStorageAssociation	1.3.6.1.4.1.1123.3.1.2.22.1.12.1.0.6			Existing controller changed
NTF trap7forMassStorageAssociation	1.3.6.1.4.1.1123.3.1.2.22.1.12.1.0.7			Existing device changed
INT a12MassStorageAssociationEventType	1.3.6.1.4.1.1123.3.1.2.22.1.12.1.1	INTEGER	read-only	The type of Mass storage association where a change has occurred
INT a12EventSeverity	1.3.6.1.4.1.1123.3.1.2.22.1.12.1.2	INTEGER	read-only	The severity of this event.
INT a12EventIsStateBased	1.3.6.1.4.1.1123.3.1.2.22.1.12.1.3	INTEGER	read-only	The value of this attribute determined whether the Event being reported is a state-based Event or not. If the value of this attribute is TRUE then the Event is state-based. Else the Event is not state-based
NUM a12EventStateKey	1.3.6.1.4.1.1123.3.1.2.22.1.12.1.4	DmiInteger	read-only	This attribute holds the key identifying a row of the Event State group within the Component in which the event generator group is located. The Current State attribute within the row contains the current state of this state-based event. The current state can be one of the four severities: OK, Non-Critical, Critical, and Non-Recoverable.
STR a12AssociatedGroup	1.3.6.1.4.1.1123.3.1.2.22.1.12.1.5	DmiDisplaystring	read-only	The class name of the group that is associated with the events defined in this EventGeneration group.
INT a12EventSystem	1.3.6.1.4.1.1123.3.1.2.22.1.12.1.6	INTEGER	read-only	The mass storage association object type which is causing a change.
INT a12EventSubsystem	1.3.6.1.4.1.1123.3.1.2.22.1.12.1.7	INTEGER	read-only	The minor functional aspect of the product causing the fault.
INT a12EventSolution	1.3.6.1.4.1.1123.3.1.2.22.1.12.1.8	INTEGER	read-only	A solution to the problem that caused the event.
INT a12InstanceDataPresent	1.3.6.1.4.1.1123.3.1.2.22.1.12.1.9	INTEGER	read-only	Indicates whether the second event block contains instance-speci ic data.
STR a12EventMessage	1.3.6.1.4.1.1123.3.1.2.22.1.12.1.10	DmiDisplaystring	read-only	Auxiliary information related to the event.
tBusPortAssociation	1.3.6.1.4.1.1123.3.1.2.22.1.13		not-accessible	Bus Port Association
eBusPortAssociation	1.3.6.1.4.1.1123.3.1.2.22.1.13.1		not-accessible
NUM a13BusPortAssociationIndex	1.3.6.1.4.1.1123.3.1.2.22.1.13.1.1	DmiInteger	read-only	An index into the Bus Port Association table. This index is the same as the index in the Association group that defines the bus port association.
NUM a13NegotiatedSpeed	1.3.6.1.4.1.1123.3.1.2.22.1.13.1.2	DmiInteger	read-only	The maximum burst transfer rate, in millions of bytes, which was negotiated between the two associated bus ports.
NUM a13NegotiatedWidth	1.3.6.1.4.1.1123.3.1.2.22.1.13.1.3	DmiInteger	read-only	The width, in bits, of the bus ports data path which was negotiated between the two associated bus ports.
tOperationalState	1.3.6.1.4.1.1123.3.1.2.22.1.14		not-accessible	This group provides the operational state, usage, and availabili y status, and administrative state indicators for specific Device Group instance .
eOperationalState	1.3.6.1.4.1.1123.3.1.2.22.1.14.1		not-accessible
NUM a14OperationalStateInstanceIndex	1.3.6.1.4.1.1123.3.1.2.22.1.14.1.1	DmiInteger	read-only	The Index into the Operational State table.
NUM a14DeviceGroupIndex	1.3.6.1.4.1.1123.3.1.2.22.1.14.1.2	DmiInteger	read-only	The group ID of the group referencing this instance.
INT a14OperationalStatus	1.3.6.1.4.1.1123.3.1.2.22.1.14.1.3	INTEGER	read-only	The operational status of the Device Group instance.
INT a14UsageState	1.3.6.1.4.1.1123.3.1.2.22.1.14.1.4	INTEGER	read-only	The usage state of the Device Group instance.
INT a14AvailabilityStatus	1.3.6.1.4.1.1123.3.1.2.22.1.14.1.5	INTEGER	read-only	The availability status of the Device Group instance.
INT a14AdministrativeState	1.3.6.1.4.1.1123.3.1.2.22.1.14.1.6	INTEGER	read-only	The administrative state of the Device Group instance.
NUM a14FatalErrorCount	1.3.6.1.4.1.1123.3.1.2.22.1.14.1.7	DmiCounter	read-only	The accumulated Fatal or Non-recoverable error count for this Device Group instance.
NUM a14MajorErrorCount	1.3.6.1.4.1.1123.3.1.2.22.1.14.1.8	DmiCounter	read-only	The accumulated Major or Critical error count for this Device Group instance.
NUM a14WarningErrorCount	1.3.6.1.4.1.1123.3.1.2.22.1.14.1.9	DmiCounter	read-only	The accumulated Warning or Non-Critical error count for this Device Group instance.
INT a14CurrentErrorStatus	1.3.6.1.4.1.1123.3.1.2.22.1.14.1.10	INTEGER	read-only	This attribute presents the current error status for this Device Group instance. The most critical error status in effect should be presented. I.e. if a part of the Device Group instance is 'Critical', while other status is 'Non-critical' then the status 'Critical' should be reported.
INT a14DevicePredictedFailureStatus	1.3.6.1.4.1.1123.3.1.2.22.1.14.1.11	INTEGER	read-only	Enumeration describing the current Device Predicted Failure Status (e.g.: the S.M.A.R.T. status of the device).
tSymbiosEventPolling	1.3.6.1.4.1.1123.3.1.2.22.1.15		not-accessible	This group is the Symbios Vendor unique group for dealing with Event Polling.
eSymbiosEventPolling	1.3.6.1.4.1.1123.3.1.2.22.1.15.1		not-accessible
NUM a15SymbiosFlag	1.3.6.1.4.1.1123.3.1.2.22.1.15.1.1	DmiInteger	read-write	A Symbios Vendor Unique Flag.
INT a15SmartEventPolling	1.3.6.1.4.1.1123.3.1.2.22.1.15.1.2	INTEGER	read-write	A flag indicating whether or not the CI will poll for SMART events.
INT a15ScanEventPolling	1.3.6.1.4.1.1123.3.1.2.22.1.15.1.3	INTEGER	read-write	A flag indicating whether or not the CI will scan for a change in Devices and Controllers.
INT a15Saf_teEventPolling	1.3.6.1.4.1.1123.3.1.2.22.1.15.1.4	INTEGER	read-write	A flag indicating whether or not the CI will poll for SAF-TE events.
NUM a15EventPollingPeriod	1.3.6.1.4.1.1123.3.1.2.22.1.15.1.5	DmiInteger	read-write	The event poll period in number of minutes.
INT a15ControlLevelForDomainValidationErrorR	1.3.6.1.4.1.1123.3.1.2.22.1.15.1.6	INTEGER	read-write	This indicates the control level for performing domain validatio based on Error Rate.
NUM a15ControlLevelForDomainValidationSchedu	1.3.6.1.4.1.1123.3.1.2.22.1.15.1.7	DmiInteger	read-write	This indicates the number of hours between scheduled runs of domain validation. Zero indicates that no scheduled run should be performed.
tSymbiosDevice	1.3.6.1.4.1.1123.3.1.2.22.1.16		not-accessible	This group is a Symbios Vendor unique group for dealing with Devices.
eSymbiosDevice	1.3.6.1.4.1.1123.3.1.2.22.1.16.1		not-accessible
NUM a16SymbiosDeviceIndex	1.3.6.1.4.1.1123.3.1.2.22.1.16.1.1	DmiInteger	read-only	An index into the Symbios Vendor Unique Device info table. This index corresponds to the Storage Device index.
INT a16SmartReportingCapability	1.3.6.1.4.1.1123.3.1.2.22.1.16.1.2	INTEGER	read-write	A flag indicating the state of a Devices's SMART reporting capability.
INT a16ControlLevelForDomainValidationMargin	1.3.6.1.4.1.1123.3.1.2.22.1.16.1.3	INTEGER	read-write	This indicates the control level for margining while performing domain validation for this device.
INT a16ControlLevelForDomainValidationSkewin	1.3.6.1.4.1.1123.3.1.2.22.1.16.1.4	INTEGER	read-write	This indicates the control level for skewing while performing domain validation for this device.
INT a16MaximumAllowedNegotiatedSpeed	1.3.6.1.4.1.1123.3.1.2.22.1.16.1.5	INTEGER	read-write	This indicates the maximum allowed negotiated speed while performing domain validation for this device.
INT a16MaximumAllowedNegotiatedWidth	1.3.6.1.4.1.1123.3.1.2.22.1.16.1.6	INTEGER	read-write	This indicates the maximum allowed negotiated width while performing domain validation for this device.
NUM a16DomainValidationNegotiatedSpeed	1.3.6.1.4.1.1123.3.1.2.22.1.16.1.7	DmiInteger	read-only	This indicates the maximum negotiated speed that was achieved while performing domain validation for this device. The speed is indicated in millions of bytes per second. Typically, a value of zero would represent asynchronous transfers.
NUM a16DomainValidationNegotiatedWidth	1.3.6.1.4.1.1123.3.1.2.22.1.16.1.8	DmiInteger	read-only	This indicates the maximum negotiated width that was achieved while performing domain validation for this device. The width is indicated in bits.
tSaf_teProcessor	1.3.6.1.4.1.1123.3.1.2.22.1.17		not-accessible	This group defines a SAF-TE Processor
eSaf_teProcessor	1.3.6.1.4.1.1123.3.1.2.22.1.17.1		not-accessible
NUM a17Saf_teProcessorIndex	1.3.6.1.4.1.1123.3.1.2.22.1.17.1.1	DmiInteger	read-only	An index into the SAF-TE processor table.
NUM a17StorageControllerIndex	1.3.6.1.4.1.1123.3.1.2.22.1.17.1.2	DmiInteger	read-only	An index into the Storage Controller table.
NUM a17ScsiId	1.3.6.1.4.1.1123.3.1.2.22.1.17.1.3	DmiInteger64X	read-only	The SCSI target/initiator identifier.
NUM a17ScsiLun	1.3.6.1.4.1.1123.3.1.2.22.1.17.1.4	DmiInteger64X	read-only	The SCSI logical unit number.
STR a17VendorId	1.3.6.1.4.1.1123.3.1.2.22.1.17.1.5	DmiDisplaystring	read-only	The vendor ID that is returned in the Inquiry command
STR a17ProductId	1.3.6.1.4.1.1123.3.1.2.22.1.17.1.6	DmiDisplaystring	read-only	The product ID that is returned in the Inquiry command
STR a17FirmwareRevisionLevel	1.3.6.1.4.1.1123.3.1.2.22.1.17.1.7	DmiDisplaystring	read-only	Identifies the current firmware revision of the SAF-TE processor
STR a17EnclosureUniqueIdentifier	1.3.6.1.4.1.1123.3.1.2.22.1.17.1.8	DmiDisplaystring	read-only	This field specifies the unique unit number for the SAF-TE processor.
STR a17Saf_teSpecificationRevisionLevel	1.3.6.1.4.1.1123.3.1.2.22.1.17.1.9	DmiDisplaystring	read-only	Identifies the revision of the SAF-TE interface specification to which this device claims compliance.
INT a17HasLocks	1.3.6.1.4.1.1123.3.1.2.22.1.17.1.10	INTEGER	read-only	If true, then this SAF-TE processor is contained within an enclosure that has locks.
INT a17HasSpeakers	1.3.6.1.4.1.1123.3.1.2.22.1.17.1.11	INTEGER	read-only	If true, then this SAF-TE processor is contained within an enclosure that has speakers.
INT a17DoorLocked	1.3.6.1.4.1.1123.3.1.2.22.1.17.1.12	INTEGER	read-only	If true, then this SAF-TE processor enclosure is locked.
INT a17SpeakerStatus	1.3.6.1.4.1.1123.3.1.2.22.1.17.1.13	INTEGER	read-only	If true, then this SAF-TE processor enclsoure speakers are turned on. If false, then the speakers are off or not installed.
NUM a17PowerOnMinutes	1.3.6.1.4.1.1123.3.1.2.22.1.17.1.14	DmiInteger	read-only	Total number of power on minutes.
NUM a17PowerOnCycles	1.3.6.1.4.1.1123.3.1.2.22.1.17.1.15	DmiInteger	read-only	Total number of times the SAF-TE enclosure has been power on.
INT a17TemperatureOutOfRange	1.3.6.1.4.1.1123.3.1.2.22.1.17.1.16	INTEGER	read-only	If true, then the temperature is out of range.
tSaf_teControlledFan	1.3.6.1.4.1.1123.3.1.2.22.1.18		not-accessible	This group defines status of a fan controlled by a SAF-TE Processor
eSaf_teControlledFan	1.3.6.1.4.1.1123.3.1.2.22.1.18.1		not-accessible
NUM a18Saf_teControlledFanIndex	1.3.6.1.4.1.1123.3.1.2.22.1.18.1.1	DmiInteger	read-only	An index into the SAF-TE controlled fan table.
NUM a18Saf_teProcessorIndex	1.3.6.1.4.1.1123.3.1.2.22.1.18.1.2	DmiInteger	read-only	The Index to the SAF-TE proccessor that is controlling this fan.
INT a18Status	1.3.6.1.4.1.1123.3.1.2.22.1.18.1.3	INTEGER	read-only	The fan status.
tSaf_teControlledPowerSupply	1.3.6.1.4.1.1123.3.1.2.22.1.19		not-accessible	This group defines status of a Power Supply controlled by a SAF-TE Processor
eSaf_teControlledPowerSupply	1.3.6.1.4.1.1123.3.1.2.22.1.19.1		not-accessible
NUM a19Saf_teControlledPowerSupplyIndex	1.3.6.1.4.1.1123.3.1.2.22.1.19.1.1	DmiInteger	read-only	An index into the SAF-TE controlled Power Supply table.
NUM a19Saf_teProcessorIndex	1.3.6.1.4.1.1123.3.1.2.22.1.19.1.2	DmiInteger	read-only	The Index to the SAF-TE proccessor that is controlling this Power Supply.
INT a19Status	1.3.6.1.4.1.1123.3.1.2.22.1.19.1.3	INTEGER	read-only	The Power Supply status.
tSaf_teControlledSlot	1.3.6.1.4.1.1123.3.1.2.22.1.20		not-accessible	This group defines status of a Slot controlled by a SAF-TE Processor
eSaf_teControlledSlot	1.3.6.1.4.1.1123.3.1.2.22.1.20.1		not-accessible
NUM a20Saf_teControlledSlotIndex	1.3.6.1.4.1.1123.3.1.2.22.1.20.1.1	DmiInteger	read-only	An index into the SAF-TE controlled Slot table.
NUM a20Saf_teProcessorIndex	1.3.6.1.4.1.1123.3.1.2.22.1.20.1.2	DmiInteger	read-only	The Index to the SAF-TE proccessor table that is controlling this Slot.
NUM a20ScsiId	1.3.6.1.4.1.1123.3.1.2.22.1.20.1.3	DmiInteger64X	read-only	The SCSI target/initiator identifier for this slot.
NUM a20NumberOfInsertions	1.3.6.1.4.1.1123.3.1.2.22.1.20.1.4	DmiInteger	read-only	The total number of device insertions for this slot while the enclosure is powered on.
INT a20State	1.3.6.1.4.1.1123.3.1.2.22.1.20.1.5	INTEGER	read-only	The slot state.
INT a20Rebuild	1.3.6.1.4.1.1123.3.1.2.22.1.20.1.6	INTEGER	read-only	Rebuild status
INT a20DeviceFault	1.3.6.1.4.1.1123.3.1.2.22.1.20.1.7	INTEGER	read-only	If true, the device has exhibited some hardware or data fault.
INT a20InFailedArray	1.3.6.1.4.1.1123.3.1.2.22.1.20.1.8	INTEGER	read-only	If true, the device is in an array and an error has occurred on any member of the array.
INT a20InCriticalArray	1.3.6.1.4.1.1123.3.1.2.22.1.20.1.9	INTEGER	read-only	If true, the device is in an array that is non fault-tolerant.
INT a20ParityCheck	1.3.6.1.4.1.1123.3.1.2.22.1.20.1.10	INTEGER	read-only	If true, the device is in an array that is undergoing a parity check operation.
INT a20PredictedFault	1.3.6.1.4.1.1123.3.1.2.22.1.20.1.11	INTEGER	read-only	If true, the device has been tagged by a fault prediction algorithm as being likely to fail in the near future.
tSaf_teControlledTemperatureSensor	1.3.6.1.4.1.1123.3.1.2.22.1.21		not-accessible	This group defines status of a Temperature sensor controlled by a SAF-TE Processor
eSaf_teControlledTemperatureSensor	1.3.6.1.4.1.1123.3.1.2.22.1.21.1		not-accessible
NUM a21Saf_teControlledTemperatureSensorInde	1.3.6.1.4.1.1123.3.1.2.22.1.21.1.1	DmiInteger	read-only	An index into the SAF-TE controlled Temperature sensor table.
NUM a21Saf_teProcessorIndex	1.3.6.1.4.1.1123.3.1.2.22.1.21.1.2	DmiInteger	read-only	The Index to the SAF-TE proccessor that is controlling this Temperature sensor.
NUM a21Temperature	1.3.6.1.4.1.1123.3.1.2.22.1.21.1.3	DmiInteger	read-only	The current temperature in degrees Fahrenheit.
tNetworkAdapter802PortGroup	1.3.6.1.4.1.1123.3.1.2.22.1.22		not-accessible	Contains objects related to each of the network ports on the network adapter.
eNetworkAdapter802PortGroup	1.3.6.1.4.1.1123.3.1.2.22.1.22.1		not-accessible
NUM a22PortIndex	1.3.6.1.4.1.1123.3.1.2.22.1.22.1.1	DmiInteger	read-only	This attribute is the ordinal of the network port within the network adapter, i.e. the 'port number'.
STR a22PermanentNetworkAddress	1.3.6.1.4.1.1123.3.1.2.22.1.22.1.2	DmiDisplaystring	read-only	This is the node address stored permanently in the adapter.
STR a22CurrentNetworkAddress	1.3.6.1.4.1.1123.3.1.2.22.1.22.1.3	DmiDisplaystring	read-only	This is the node address that can be modified by software, sometimes referred to as the Locally Administered Address (LAA).
INT a22ConnectorType	1.3.6.1.4.1.1123.3.1.2.22.1.22.1.4	INTEGER	read-only	This is the type of connector currently being used to physically attach this port to the LAN.
NUM a22DataRate	1.3.6.1.4.1.1123.3.1.2.22.1.22.1.5	DmiInteger	read-only	This is the rate at which data is transferred over the LAN in Mbps.
tNetworkAdapterHardwareGroup	1.3.6.1.4.1.1123.3.1.2.22.1.23		not-accessible	Contains objects related to the network adapter hardware.
eNetworkAdapterHardwareGroup	1.3.6.1.4.1.1123.3.1.2.22.1.23.1		not-accessible
INT a23NetworkTopology	1.3.6.1.4.1.1123.3.1.2.22.1.23.1.1	INTEGER	read-only	This is the network media access method/topology supported by this adapter.
INT a23TransmissionCapability	1.3.6.1.4.1.1123.3.1.2.22.1.23.1.2	INTEGER	read-only	The transmission capabilities of the adapter.
NUM a23NetworkAdapterRamSize	1.3.6.1.4.1.1123.3.1.2.22.1.23.1.3	DmiInteger	read-only	This is the total size of adapter RAM in Kb.
INT a23BusType	1.3.6.1.4.1.1123.3.1.2.22.1.23.1.4	INTEGER	read-only	This is the type of bus used to interface the adapter to the host.
INT a23BusWidth	1.3.6.1.4.1.1123.3.1.2.22.1.23.1.5	INTEGER	read-only	This is the width (in bits) of the data path used to interface the adapter with the host.
NUM a23AdapterHardwareIndex	1.3.6.1.4.1.1123.3.1.2.22.1.23.1.6	DmiInteger	read-only	An index into the Network Adapter Hardware table.
tEventGenerationForPowerSupply	1.3.6.1.4.1.1123.3.1.2.22.1.24		not-accessible
eEventGenerationForPowerSupply	1.3.6.1.4.1.1123.3.1.2.22.1.24.1		not-accessible
INT a24EventType	1.3.6.1.4.1.1123.3.1.2.22.1.24.1.1	INTEGER	read-only	The type of event that has occurred.
INT a24EventSeverity	1.3.6.1.4.1.1123.3.1.2.22.1.24.1.2	INTEGER	read-only	The severity of this event.
INT a24IsEventState_based	1.3.6.1.4.1.1123.3.1.2.22.1.24.1.3	INTEGER	read-only	The value of this attribute determines whether the Event being reported is a state-based Event or not. If the value of this attribute is TRUE then the Event is state-based. Otherwise the Event is not state-based.
NUM a24EventStateKey	1.3.6.1.4.1.1123.3.1.2.22.1.24.1.4	DmiInteger	read-only	A unique, single integer key into the Event State group if this is a state-based Event. If this is not a state-based Event then this this attribute's value is not defined.
STR a24AssociatedGroup	1.3.6.1.4.1.1123.3.1.2.22.1.24.1.5	DmiDisplaystring	read-only	The class name of the group that is associated with the events defined in this EventGeneration group.
INT a24EventSystem	1.3.6.1.4.1.1123.3.1.2.22.1.24.1.6	INTEGER	read-only	The major functional aspect of the product causing the fault.
INT a24EventSubsystem	1.3.6.1.4.1.1123.3.1.2.22.1.24.1.7	INTEGER	read-only	The minor functional aspect of the product causing the fault.
INT a24IsInstanceDataPresent	1.3.6.1.4.1.1123.3.1.2.22.1.24.1.8	INTEGER	read-only	Indicates whether the second event block contains instance-speci ic data.
STR a24EventMessage	1.3.6.1.4.1.1123.3.1.2.22.1.24.1.9	DmiDisplaystring	read-only	Auxillary information releated to the event This text contains the name of the Probe
tEventGenerationForTemperatureProbe	1.3.6.1.4.1.1123.3.1.2.22.1.25		not-accessible
eEventGenerationForTemperatureProbe	1.3.6.1.4.1.1123.3.1.2.22.1.25.1		not-accessible
INT a25EventType	1.3.6.1.4.1.1123.3.1.2.22.1.25.1.1	INTEGER	read-only	The type of event that has occurred.
INT a25EventSeverity	1.3.6.1.4.1.1123.3.1.2.22.1.25.1.2	INTEGER	read-only	The severity of this event.
INT a25IsEventState_based	1.3.6.1.4.1.1123.3.1.2.22.1.25.1.3	INTEGER	read-only	The value of this attribute determines whether the Event being reported is a state-based Event or not. If the value of this attribute is TRUE then the Event is state-based. Otherwise the Event is not state-based.
NUM a25EventStateKey	1.3.6.1.4.1.1123.3.1.2.22.1.25.1.4	DmiInteger	read-only	A unique, single integer key into the Event State group if this is a state-based Event. If this is not a state-based Event then this this attribute's value is not defined.
STR a25AssociatedGroup	1.3.6.1.4.1.1123.3.1.2.22.1.25.1.5	DmiDisplaystring	read-only	The class name of the group that is associated with the events defined in this Event Generation group.
INT a25EventSystem	1.3.6.1.4.1.1123.3.1.2.22.1.25.1.6	INTEGER	read-only	The major functional aspect of the product causing the fault.
INT a25EventSubsystem	1.3.6.1.4.1.1123.3.1.2.22.1.25.1.7	INTEGER	read-only	The minor functional aspect of the product causing the fault.
INT a25IsInstanceDataPresent	1.3.6.1.4.1.1123.3.1.2.22.1.25.1.8	INTEGER	read-only	Indicates whether the second event block contains instance-speci ic data.
STR a25EventMessage	1.3.6.1.4.1.1123.3.1.2.22.1.25.1.9	DmiDisplaystring	read-only	Auxillary information releated to the event This text contains the name of the Probe
tEventGenerationForFans	1.3.6.1.4.1.1123.3.1.2.22.1.26		not-accessible
eEventGenerationForFans	1.3.6.1.4.1.1123.3.1.2.22.1.26.1		not-accessible
INT a26EventType	1.3.6.1.4.1.1123.3.1.2.22.1.26.1.1	INTEGER	read-only	The type of event that has occurred.
INT a26EventSeverity	1.3.6.1.4.1.1123.3.1.2.22.1.26.1.2	INTEGER	read-only	The severity of this event.
INT a26IsEventState_based	1.3.6.1.4.1.1123.3.1.2.22.1.26.1.3	INTEGER	read-only	The value of this attribute determines whether the Event being reported is a state-based Event or not. If the value of this attribute is TRUE then the Event is state-based. Otherwise the Event is not state-based.
NUM a26EventStateKey	1.3.6.1.4.1.1123.3.1.2.22.1.26.1.4	DmiInteger	read-only	A unique, single integer key into the Event State group if this is a state-based Event. If this is not a state-based Event then this this attribute's value is not defined.
STR a26AssociatedGroup	1.3.6.1.4.1.1123.3.1.2.22.1.26.1.5	DmiDisplaystring	read-only	The class name of the group that is associated with the events defined in this Event Generation group.
INT a26EventSystem	1.3.6.1.4.1.1123.3.1.2.22.1.26.1.6	INTEGER	read-only	The major functional aspect of the product causing the fault.
INT a26EventSubsystem	1.3.6.1.4.1.1123.3.1.2.22.1.26.1.7	INTEGER	read-only	The minor functional aspect of the product causing the fault.
INT a26IsInstanceDataPresent	1.3.6.1.4.1.1123.3.1.2.22.1.26.1.8	INTEGER	read-only	Indicates whether the second event block contains instance-speci ic data.
STR a26EventMessage	1.3.6.1.4.1.1123.3.1.2.22.1.26.1.9	DmiDisplaystring	read-only	Auxillary information releated to the event This text contains the name of the Probe
tSymbiosHealth	1.3.6.1.4.1.1123.3.1.2.22.1.27		not-accessible	This group is the Symbios Vendor unique group for reporting the health.
eSymbiosHealth	1.3.6.1.4.1.1123.3.1.2.22.1.27.1		not-accessible
INT a27OverallHealthStatus	1.3.6.1.4.1.1123.3.1.2.22.1.27.1.1	INTEGER	read-only	Status indicating the overall health.
INT a27OverallControllerHealthStatus	1.3.6.1.4.1.1123.3.1.2.22.1.27.1.2	INTEGER	read-only	Status indicating the overall health of the controllers.
NUM a27Non_recoverableControllers	1.3.6.1.4.1.1123.3.1.2.22.1.27.1.3	DmiInteger	read-only	The number of controllers reporting a non-recoverable status.
NUM a27DegradedControllers	1.3.6.1.4.1.1123.3.1.2.22.1.27.1.4	DmiInteger	read-only	The number of controllers reporting a degraded status.
INT a27OverallDeviceHealthStatus	1.3.6.1.4.1.1123.3.1.2.22.1.27.1.5	INTEGER	read-only	Status indicating the overall health of the devices.
NUM a27Non_recoverableDevices	1.3.6.1.4.1.1123.3.1.2.22.1.27.1.6	DmiInteger	read-only	The number of devices reporting a non-recoverable status.
NUM a27DegradedDevices	1.3.6.1.4.1.1123.3.1.2.22.1.27.1.7	DmiInteger	read-only	The number of devices reporting a degraded status.
DMI a27DataValuesTimeStamp	1.3.6.1.4.1.1123.3.1.2.22.1.27.1.8	DmiDateX	read-only	The time the data values where last changed.
DMI a27HardwareTimeStamp	1.3.6.1.4.1.1123.3.1.2.22.1.27.1.9	DmiDateX	read-only	The time the hardware recognition was last changed.
tSymbiosController	1.3.6.1.4.1.1123.3.1.2.22.1.28		not-accessible	This group is a Symbios Vendor unique group for dealing with Controllers.
eSymbiosController	1.3.6.1.4.1.1123.3.1.2.22.1.28.1		not-accessible
NUM a28SymbiosControllerIndex	1.3.6.1.4.1.1123.3.1.2.22.1.28.1.1	DmiInteger	read-only	An index into the Symbios Vendor Unique Controller table. This index corresponds to the Storage Controller index.
DMI a28LastRunDateForDv	1.3.6.1.4.1.1123.3.1.2.22.1.28.1.2	DmiDateX	read-only	This indicates the date and time of the last time Domain Validation was completed on this controller.
NUM a28IoFactorForDvErrorRate	1.3.6.1.4.1.1123.3.1.2.22.1.28.1.3	DmiInteger	read-write	This indicates the I/O factor to use for calculating the Domain Validation Error Rate.
NUM a28TimeFactorForDvErrorRate	1.3.6.1.4.1.1123.3.1.2.22.1.28.1.4	DmiInteger	read-write	This indicates the time factor to use for calculating the Domain Validation Error Rate.
NUM a28ErrorCountFactorForDvErrorRate	1.3.6.1.4.1.1123.3.1.2.22.1.28.1.5	DmiInteger	read-write	This indicates the error count factor to use for calculating the Domain Validation Error Rate.
INT a28DvStatus	1.3.6.1.4.1.1123.3.1.2.22.1.28.1.6	INTEGER	read-write	This indicates the status of Domain Validation for this controll r. Writing a value of 4 to this attribute will cause Domain Validation to be run.
tMiftomib	1.3.6.1.4.1.1123.3.1.2.22.1.99		not-accessible	This group defines attributes required for DMI to SNMP translati n.
eMiftomib	1.3.6.1.4.1.1123.3.1.2.22.1.99.1		not-accessible
STR a99MibName	1.3.6.1.4.1.1123.3.1.2.22.1.99.1.1	DmiDisplaystring	read-only	The MIB name that defines this MIF
STR a99MibOid	1.3.6.1.4.1.1123.3.1.2.22.1.99.1.2	DmiDisplaystring	read-only	The MIB OID that corresponds to this MIF
NUM a99DisableTrap	1.3.6.1.4.1.1123.3.1.2.22.1.99.1.3	DmiInteger	read-write	This attribute can be changed to disable sending oftraps from this component

RFC description

Symbios SCSI controller DMI MIB providing component identification, manufacturer, and product information for SCSI devices.

Start monitoring Symbios/LSI legacy SCSI storage controller (component identity/install-verification status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SYMBIOSDMI20MIFDEFINITIONID22-MIB

What Is SYMBIOSDMI20MIFDEFINITIONID22-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description