All MIBs › SWITCH-ATM-MIB
Last Updated: 1997-06-20
Category: ATM, Switch Management - General
Description: Manages switch ATM interface configuration, virtual circuit state, and ATM cell transport.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is SWITCH-ATM-MIB?
SWITCH-ATM-MIB is a MIB module for managing Asynchronous Transfer Mode (ATM) support on a network switch, covering interface configuration, virtual circuit/virtual path state, and cell transport, part of the legacy ATM switching technology area. The module description notes it assumes a single virtual path identifier (VPI) per interface determined by the underlying software rather than exposed as a table index, indicating the module focuses on virtual channel-level rather than full VP-switching configuration. No specific object names were extracted, but ATM switch MIBs of this kind typically expose per-port ATM interface parameters, connection/VC admission state, and cell-layer statistics. This data would be used to monitor hardware status of ATM interface cards and the operational state of virtual circuits carrying traffic, which is important for detecting cell loss, misconfigured VCs, or interface faults. It likely depends on or parallels the IETF ATM-MIB (RFC 2515) conventions for standard ATM management objects. It is deployed on switches supporting legacy ATM transport, common in older carrier and enterprise backbone networks, making this SWITCH-ATM-MIB reference useful for administrators maintaining legacy ATM equipment.
IPNetwork Monitor allows you to monitor SNMP objects defined in SWITCH-ATM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- ATM-capable network switch
Monitoring Examples
No sample objects were available for this module, so a concrete monitoring scenario using real object names cannot be constructed; based on the module description, an admin would typically expect to poll a per-interface ATM configuration table and a virtual circuit state table to detect VC failures or cell-layer errors, but specific object names cannot be confirmed from the available data.
What Can Be Monitored
- ATM interface configuration (unconfirmed - no objects available)
This MIB depends on
Related MIBs
Imported Objects
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| MacAddress | |
| RowStatus | |
| TEXTUAL-CONVENTION |
From TELESYN-ATI-TC
| atmModule | OBJECT-IDENTITY |
How to Use in IPNetwork Monitor
Example using atmxLayerStatsTxCells OID:
Select an ATM-capable network switch, legacy ATM transport (interface/virtual-circuit status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type atmxLayerStatsTxCells into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The total number of successfully transmitted cells. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| switchAtmMib | 1.3.6.1.4.1.207.8.9.2.1.1 | The MIB module for ATM support. This module is designed with the assumption that only one virtual path identifier (VPI) may be assigned and is usually determined by the underlying software implementation. The VPI is never used as an index in any table in this module. | ||
| atmxPortGroup | 1.3.6.1.4.1.207.8.9.2.1.1.1 | |||
| atmxPortTable | 1.3.6.1.4.1.207.8.9.2.1.1.1.1 | not-accessible | A table of port layer status and parameter information for the UNI's physical interface. | |
| atmxPortEntry | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1 | not-accessible | An entry in the table, containing information about the physical layer of a UNI interface. | |
| ATM atmxPortIndex | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.1 | AtmPortIndex | not-accessible | A unique value which identifies this atm submodule port. |
| STR atmxPortDescription | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.2 | DisplayString | read-write | A description for this atm port. |
| ATM atmxPortTransmissionType | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.3 | AtmTransmissionTypes | read-only | The transmission type of this port. For example, for a port using the Sonet STS-3c physical layer at 155.52 Mbs, this object would have the value 'sonetSTS3c'. |
| ATM atmxPortMediaType | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.4 | AtmMediaTypes | read-only | The type of media being used on this port. For example for a port using coaxial cable, the object would have the value 'coaxCable'. |
| ATM atmxPortOperStatus | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.5 | AtmOperStatus | read-only | The operational state (i.e., actual) of this port. The ILMI should not alarm on a physical interface when the value of this object is 'outOfService'. This capability is useful if the equipment is to be disconnected or for troubleshooting purposes. A value of 'loopBack' indicates that loopback is in place. |
| INT atmxPortMaxVCCs | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.6 | INTEGER | read-only | The maximum number of VCCs supported on this UNI. |
| INT atmxPortMaxVciBits | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.7 | INTEGER | read-only | The number of active VCI bits on this interface. |
| ADR atmxPortAddress | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.8 | AtmAddress | read-write | The ATM address assigned to this port. The value of this attribute is normally set via the ILMI. If the ILMI Address registration mib, ATM-FORUM-ADDR-REG, is supported and the the value of atmxPortIlmiStatus is 'up' than atmxPortAddress should have a MAX-ACCESS of read-only. |
| INT atmxPortSignalingVersion | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.9 | INTEGER | read-write | Version of the ATM forum UNI Signaling. |
| INT atmxPortSignalingVci | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.10 | INTEGER | read-only | Signaling Vci. ATM Forum has defined VPI/VCI as VPI 0, VCI 5 for signaling. |
| INT atmxPortILMIVci | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.11 | INTEGER | read-only | ILMI Vci. ATM Forum has defined the VPI 0, VCI 16 for ILMI. |
| INT atmxPortEnableIlmi | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.12 | INTEGER | read-write | ILMI Enable. |
| INT atmxPortEnableIlmiPoll | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.13 | INTEGER | read-write | ILMI Poll Enable. |
| INT atmxPortEnablePlScramble | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.14 | INTEGER | read-write | Payload Scrambling Enable. |
| INT atmxPortClock | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.15 | INTEGER | read-write | ATM Port clock mode. |
| MAC atmxPortMacAddress | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.16 | MacAddress | read-only | ATM Port MAC Address. |
| INT atmxPortAdaptorRamSize | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.17 | INTEGER | read-only | Segmentation and reassembly memory size in bytes. |
| ATM atmxPortIlmiStatus | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.18 | AtmConnectionOperStatusCodes | read-only | ILMI status. |
| ATM atmxPortSignalingStatus | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.19 | AtmConnectionOperStatusCodes | read-only | Signaling Status. |
| INT atmxPortSignalingMode | 1.3.6.1.4.1.207.8.9.2.1.1.1.1.1.20 | INTEGER | read-write | If this has the value 'pvc' then signaling, ILMI and ILMI polling will be automatically disabled. |
| atmxLecGroup | 1.3.6.1.4.1.207.8.9.2.1.1.2 | |||
| atmxLecTable | 1.3.6.1.4.1.207.8.9.2.1.1.2.1 | not-accessible | A table of LEC status and parameter information. | |
| atmxLecEntry | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1 | not-accessible | An entry in the table, containing information about the indicated LEC. | |
| ATM atmxLecIndex | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.1 | AtmLecIndex | not-accessible | A unique value which identifies this LEC entry. |
| STR atmxLecDescription | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.2 | DisplayString | read-create | A description for this LEC. |
| STR atmxElanName | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.3 | DisplayString | read-create | A Name for the ELAN. |
| INT atmxLecConfigMode | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.4 | INTEGER | read-create | Configuration Mode for this LEC. |
| ADR atmxLecServerAddress | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.5 | AtmAddress | read-create | ATM Address of the LE Configuration Server if the configuration mode is auto; else, the LE Server ATM Address. |
| MAC atmxLecUnicastMacAddress | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.6 | MacAddress | read-only | The Local Unicast MAC address for this LEC. This is now obsolete because the information can be obtained from the vport entry identified by atmxLecVPortNumber. |
| INT atmxLecMaxUnknownFrameCount | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.7 | INTEGER | read-create | Maximum number of frames to the BUS for a given unicast LAN destination within the Maximum unknown Frame time. |
| INT atmxLecMaxArpRetryCount | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.8 | INTEGER | read-create | Maximum number of times LE_ARP_REQUEST will be retried for a given frame's LAN destination. |
| INT atmxLecArpRespTime | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.9 | INTEGER | read-create | Maximum time in seconds that the LEC expects an LE_ARP_REQUEST/LE_ARP_RESPONSE cycle to take. |
| INT atmxLecMaxUnknownFrameTime | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.10 | INTEGER | read-create | Time period in seconds for the maximum number of frames that can be sent to the BUS for a given LAN destination. |
| INT atmxLecControlTimeout | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.11 | INTEGER | read-create | Time out period in seconds for timing out most request response control frame interations. |
| U32 atmxLecVccTimeout | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.12 | Unsigned32 | read-create | Maximum in-active time period in seconds a data direct VCC will be active before being released. A value of 0 indicates that it will never be release. |
| INT atmxLecAgeingTime | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.13 | INTEGER | read-create | Maximum time in seconds that an LE client will maintain an entry in its LE-ARP cache in the absence of verification. |
| INT atmxLecFlushTimeout | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.14 | INTEGER | read-create | Time limit in seconds to wait to receive an LE_FLUSH_RESPONSE after the LE_FLUSH_REQUEST has been sent before taking recovery action. |
| INT atmxLecVPortNumber | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.15 | INTEGER | read-only | The Virtual port number with which this LEC is associated. If the value of this object is 0, then no virtual port has been assigned and the LEC is not active. |
| INT atmxLecProtocolState | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.16 | INTEGER | read-only | This object contains the LAN emulation protocol state. |
| ROW atmxLecRowStatus | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.17 | RowStatus | read-create | This object is used to create and delete entries. Only the values 'active', 'createAndGo', and 'delete are supported. |
| IFI atmxLecIfIndex | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.18 | IfIndexOrZero | read-only | This object contains the ifIndex of the corresponding entry in the ifTable. If no such entry exists or unknown then value of this object is 0. |
| INT atmxLecId | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.19 | INTEGER | read-only | A value assigned by the LAN Emulation Service (LES) for the LEC identified by atmLecIndex. The value 0 indicates the LES has not assigned a value. |
| ATM atmxLecControlDirectVcc | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.20 | AtmVci | read-only | The VCC assigned for the Control Direct connection. The value 0 indicates the VCC is not set. |
| ATM atmxLecControlDistributeVcc | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.21 | AtmVci | read-only | The VCC assigned for the Control Distribute connection. The value 0 indicates the VCC is not set. |
| ATM atmxLecMulticastSendVcc | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.22 | AtmVci | read-only | The VCC assigned for Multicast send. The value 0 indicates the VCC is not set. |
| ATM atmxLecMulticastForwardVcc | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.23 | AtmVci | read-only | The VCC assigned for multicast forwarding. The value 0 indicates the VCC is not set. |
| ATM atmxLecVlanNumber | 1.3.6.1.4.1.207.8.9.2.1.1.2.1.1.24 | AtmxVlanRange | read-create | The virtual LAN number to which this LEC is attached. This object is required for row creation and the value of this object must correspond to an existing vLanNumber object in the 'SWITCH-VLAN-MIB.vLanTable'. After a successful row creation, this value may change as a result of moving the virtual port, atmxLecIfIndex, to a different Vlan. |
| atmxCipGroup | 1.3.6.1.4.1.207.8.9.2.1.1.3 | |||
| atmxCipTable | 1.3.6.1.4.1.207.8.9.2.1.1.3.1 | not-accessible | A table of CIP status and parameter information. | |
| atmxCipEntry | 1.3.6.1.4.1.207.8.9.2.1.1.3.1.1 | not-accessible | An entry in the table, containing information about the indicated CIP. | |
| ATM atmxCipIndex | 1.3.6.1.4.1.207.8.9.2.1.1.3.1.1.1 | AtmCipIndex | not-accessible | A unique value which identifies this CIP entry. |
| STR atmxCipDescription | 1.3.6.1.4.1.207.8.9.2.1.1.3.1.1.2 | DisplayString | read-create | A description for this CIP. |
| IP atmxCipIPAddress | 1.3.6.1.4.1.207.8.9.2.1.1.3.1.1.3 | IpAddress | read-create | The IP address associated with this CIP entity. |
| IP atmxCipIPSubnetMask | 1.3.6.1.4.1.207.8.9.2.1.1.3.1.1.4 | IpAddress | read-create | The IP subnet mask associated with this CIP entity. |
| INT atmxCipConnectionType | 1.3.6.1.4.1.207.8.9.2.1.1.3.1.1.5 | INTEGER | read-create | The connection type of this CIP. If during row creation the value of this object is 'pvc', then at least one entry in the atmxCipVciTable is required before atmxCipRowStatus can be set to 'active'. If during row creation the value is 'svc' then atmxCipServerAtmAddress must be set before atmxCipRowStatus can be set to 'active'. |
| ATM atmxCipVci | 1.3.6.1.4.1.207.8.9.2.1.1.3.1.1.6 | AtmVci | read-create | The virtual channel identifier associated with this CIP, if PVC. |
| ADR atmxCipServerAtmAddress | 1.3.6.1.4.1.207.8.9.2.1.1.3.1.1.7 | AtmAddress | read-create | ATM Address of the ARP server for the logical IP subnet, to which this CIP belongs. This object is required if atmxCipConnectionType is 'svc'. |
| INT atmxCipMtuSize | 1.3.6.1.4.1.207.8.9.2.1.1.3.1.1.8 | INTEGER | read-create | The maximum size of the transmit or receive SDU size of all connections associated with this CIP entity. |
| IFI atmxCipIfIndex | 1.3.6.1.4.1.207.8.9.2.1.1.3.1.1.9 | IfIndexOrZero | read-only | This value of this object identifies the corresponding entry in the ifTable. If this object has the value of 0 then there is no corresponding entry in the ifTable. |
| INT atmxCipProtocolState | 1.3.6.1.4.1.207.8.9.2.1.1.3.1.1.10 | INTEGER | read-only | The state of the CIP Protocol. |
| ATM atmxCipAdmStatus | 1.3.6.1.4.1.207.8.9.2.1.1.3.1.1.11 | AtmAdminStatus | read-create | The administrative status of this CIP instance. |
| ATM atmxCipOperStatus | 1.3.6.1.4.1.207.8.9.2.1.1.3.1.1.12 | AtmOperStatus | read-only | The operational status of this CIP instance. |
| ROW atmxCipRowStatus | 1.3.6.1.4.1.207.8.9.2.1.1.3.1.1.13 | RowStatus | read-create | This object is used to create and delete atmxCipEntry. To create of a logical row, set this object to 'createAndWait'. Before this object can be set to 'active', the objects atmxCipIPAddress, atmxCipIPSubnetMask, atmxCipConnectionType must be set to the appropriate values and at least one entry must be created in the atmxCipVciTable with the same atmxCipIndex value as used with this object instance. When this object is set to 'active', the logical rows in atmxCipVciTable with the same atmxCipIndex value will also be set to 'active'. If this object is set to 'delete', the logical rows in atmxCipVciTable with the same atmxCipIndex value will also be deleted. |
| INT atmxCipRipMode | 1.3.6.1.4.1.207.8.9.2.1.1.3.1.1.14 | INTEGER | read-create | If the value of this object is 'silent', RIP daemon processes received routing packets and does NOT send routing packets over the interface identified by atmxCipIfIndex. With a value of 'active', RIP sends and receives routing packets. With a value of 'deaf' RIP sends routing packets and does not process recieved packets. With a value of 'inactive' RIP deamon does not send nor receive routing packets. |
| atmxCipVciTable | 1.3.6.1.4.1.207.8.9.2.1.1.3.2 | not-accessible | A table which contains VCIs associated with each CIP. | |
| atmxCipVciEntry | 1.3.6.1.4.1.207.8.9.2.1.1.3.2.1 | not-accessible | An entry in the table, identifying each VCI for a CIP. | |
| ATM atmxCipVciId | 1.3.6.1.4.1.207.8.9.2.1.1.3.2.1.1 | AtmClientVci | not-accessible | The virtual channel identifier associated with this CIP. |
| ROW atmxCipVciRowStatus | 1.3.6.1.4.1.207.8.9.2.1.1.3.2.1.2 | RowStatus | read-create | This object is used to create and delete entries in the atmxCipVciTable. An object instance of this object corresponds to an object instance of atmxCipRowStatus if both objects have the same for atmxCipIndex index value. There may be multiple instances of this object which correspond to the same instance of atmxCipRowStatus. To create a conceptual row in this table and the corresponding object instance atmxCipRowStatus does not exist or has the value 'notReady', the value for atmxCipVciRowStatus in an SNMP Set operation can be only 'createAndWait'. Under these conditions, atmxCipVciRowStatus cannot be set to 'active' but transitions to 'active' as a side effect of an SNMP set operation changing atmxCipRowStatus to 'active'. At least one corresponding instance of atmxCipVciRowStatus must exist before atmxCipRowStatus can transition to 'active'. To create a conceptual row in this table and the corresponding object instance atmxCipRowStatus exists with the value 'active' then the value for atmxCipVciRowStatus may be 'createAndWait' or 'createAndGo'. An SNMP Set operation may not set the value of this object to 'active' unless the the corresponde atmxCipRowStatus has the value 'active'. |
| atmxLayerStatsGroup | 1.3.6.1.4.1.207.8.9.2.1.1.4 | |||
| atmxLayerStatsTable | 1.3.6.1.4.1.207.8.9.2.1.1.4.1 | not-accessible | A table of ATM layer statistics information. | |
| atmxLayerStatsEntry | 1.3.6.1.4.1.207.8.9.2.1.1.4.1.1 | not-accessible | An entry in the table, containing information about the ATM layer statistics. | |
| C32 atmxLayerStatsTxCellsEx | 1.3.6.1.4.1.207.8.9.2.1.1.4.1.1.2 | Counter32 | read-only | The total number of successfully transmitted cells. |
| C32 atmxLayerStatsRxCells | 1.3.6.1.4.1.207.8.9.2.1.1.4.1.1.3 | Counter32 | read-only | The total number of successfully received cells. |
| C32 atmxLayerStatsTxCellDiscards | 1.3.6.1.4.1.207.8.9.2.1.1.4.1.1.4 | Counter32 | read-only | The total number of transmit cells that are discarded. |
| C32 atmxLayerStatsRxCellDiscards | 1.3.6.1.4.1.207.8.9.2.1.1.4.1.1.5 | Counter32 | read-only | The total number of receive cells that are discarded. |
| ATM atmxLayerStatsClear | 1.3.6.1.4.1.207.8.9.2.1.1.4.1.1.6 | AtmClearStats | read-write | When this attribute is set to 'clearStats', the counters for this logical row are reset to 0 and atmxLayerStatsClearTime is reset to 0. |
| INT atmxLayerStatsClearTime | 1.3.6.1.4.1.207.8.9.2.1.1.4.1.1.7 | INTEGER | read-only | Amount of time in seconds that has elapsed since the counters have been cleared. |
| aal5LayerStatsTable | 1.3.6.1.4.1.207.8.9.2.1.1.4.2 | not-accessible | A table of AAL5 layer statistics information. | |
| aal5LayerStatsEntry | 1.3.6.1.4.1.207.8.9.2.1.1.4.2.1 | not-accessible | An entry in the table, containing information about the AAL5 layer statistics. | |
| C32 aal5LayerTxOctets | 1.3.6.1.4.1.207.8.9.2.1.1.4.2.1.2 | Counter32 | read-only | The total number of successfully transmitted octets for all AAL5 connections. |
| C32 aal5LayerTxCells | 1.3.6.1.4.1.207.8.9.2.1.1.4.2.1.3 | Counter32 | read-only | The total number of successfully transmitted cells for all AAL5 connections. |
| C32 aal5LayerTxSDUs | 1.3.6.1.4.1.207.8.9.2.1.1.4.2.1.4 | Counter32 | read-only | The total number of successfully transmitted service data units for all AAL5 connections. |
| C32 aal5LayerTxSDUDiscards | 1.3.6.1.4.1.207.8.9.2.1.1.4.2.1.5 | Counter32 | read-only | The total number of transmit SDUs discarded. |
| C32 aal5LayerTxErrors | 1.3.6.1.4.1.207.8.9.2.1.1.4.2.1.6 | Counter32 | read-only | The total number of transmit SDUs that could not be transmitted due to errors. |
| C32 aal5LayerRxOctets | 1.3.6.1.4.1.207.8.9.2.1.1.4.2.1.7 | Counter32 | read-only | The total number of successfully received octets for all AAL5 connections. |
| C32 aal5LayerRxCells | 1.3.6.1.4.1.207.8.9.2.1.1.4.2.1.8 | Counter32 | read-only | The total number of successfully received cells for all AAL5 connections. |
| C32 aal5LayerRxSDUs | 1.3.6.1.4.1.207.8.9.2.1.1.4.2.1.9 | Counter32 | read-only | The total number of successfully received service data units for all AAL5 connections. |
| C32 aal5LayerRxSDUDiscards | 1.3.6.1.4.1.207.8.9.2.1.1.4.2.1.10 | Counter32 | read-only | The total number of received SDUs discarded. |
| C32 aal5LayerRxErrors | 1.3.6.1.4.1.207.8.9.2.1.1.4.2.1.11 | Counter32 | read-only | The total number of errored SDUs that received. |
| C32 aal5LayerRxSarTimeouts | 1.3.6.1.4.1.207.8.9.2.1.1.4.2.1.12 | Counter32 | read-only | The total number of partially re-assembled SDUs that were discarded. |
| C32 aal5LayerRxCrcErrors | 1.3.6.1.4.1.207.8.9.2.1.1.4.2.1.13 | Counter32 | read-only | The total number of SDUs that were received with CRC errors. |
| C32 aal5LayerRxSDUInvalidSz | 1.3.6.1.4.1.207.8.9.2.1.1.4.2.1.14 | Counter32 | read-only | The total number of SDUs discarded because their size exceeded the max SDU size. |
| ATM aal5LayerClearStats | 1.3.6.1.4.1.207.8.9.2.1.1.4.2.1.15 | AtmClearStats | read-write | When this attribute is set to 'clearStats', the counters for this logical row are reset to 0 and aal5LayerStatsClearTime is reset to 0. |
| INT aal5LayerStatsClearTime | 1.3.6.1.4.1.207.8.9.2.1.1.4.2.1.16 | INTEGER | read-only | Amount of time in seconds that has elapsed since the counters have been reset. |
| atmxVccStatsGroup | 1.3.6.1.4.1.207.8.9.2.1.1.5 | |||
| atmxVccStatsTable | 1.3.6.1.4.1.207.8.9.2.1.1.5.1 | not-accessible | A table of ATM virtual channel connection statistics information. | |
| atmxVccStatsEntry | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1 | not-accessible | An entry in the table, containing information about the ATM virtual channel connection statistics. | |
| C32 atmxVccStatsTxSDUs | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1.3 | Counter32 | read-only | The total number of transmitted SDU's on this virtual channel. |
| C32 atmxVccStatsTxCells | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1.4 | Counter32 | read-only | The total number of transmitted cells on this virtual channel. |
| C32 atmxVccStatsTxOctets | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1.5 | Counter32 | read-only | The total number of transmitted octets on this virtual channel. |
| C32 atmxVccStatsRxSDUs | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1.6 | Counter32 | read-only | The total number of received SDU's on this virtual channel. |
| C32 atmxVccStatsRxCells | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1.7 | Counter32 | read-only | The total number of received cells on this virtual channel. |
| C32 atmxVccStatsRxOctets | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1.8 | Counter32 | read-only | The total number of received octets on this virtual channel. |
| C32 atmxVccStatsTxSDUDiscards | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1.9 | Counter32 | read-only | The total number of transmit SDUs discarded on this virtual channel. |
| C32 atmxVccStatsTxErrors | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1.10 | Counter32 | read-only | The total number of transmit SDU errors on this virtual channel. |
| C32 atmxVccStatsRxSDUDiscards | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1.11 | Counter32 | read-only | The total number of receive SDU's discarded on this virtual channel. |
| C32 atmxVccStatsRxErrors | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1.12 | Counter32 | read-only | The total number of receive SDU's with errors on this virtual channel. |
| C32 atmxVccStatsRxSarTimeouts | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1.13 | Counter32 | read-only | The total number of partially re-assembled SDUs that were discarded. |
| C32 atmxVccStatsRxCrcErrors | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1.14 | Counter32 | read-only | The total number of receive SDU's crc errors on this virtual channel. |
| C32 atmxVccStatsRxOversizedSdus | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1.15 | Counter32 | read-only | The total number of receive SDU's that are oversized. |
| INT atmxVccStatsConnCreateTime | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1.16 | INTEGER | read-only | Time elapsed in seconds since the connection has been created. |
| INT atmxVccStatsConnInIdleTime | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1.17 | INTEGER | read-only | Time that has elapsed in seconds since any traffic has been received on this connection. |
| INT atmxVccStatsConnOutIdleTime | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1.18 | INTEGER | read-only | Time that has elapsed in seconds since any traffic has been sent out on this connection. |
| INT atmxVccStatsConnModifiedTime | 1.3.6.1.4.1.207.8.9.2.1.1.5.1.1.19 | INTEGER | read-only | Time that has elapsed in seconds since any connection parameters have been modified. |
| atmxLecStatsGroup | 1.3.6.1.4.1.207.8.9.2.1.1.6 | |||
| atmxLecStatsTable | 1.3.6.1.4.1.207.8.9.2.1.1.6.1 | not-accessible | A table of ATM LEC statistics information. | |
| atmxLecStatsEntry | 1.3.6.1.4.1.207.8.9.2.1.1.6.1.1 | not-accessible | An entry in the table, containing information about the LEC statistics. | |
| C32 atmxLecStatsTxArpReq | 1.3.6.1.4.1.207.8.9.2.1.1.6.1.1.2 | Counter32 | read-only | Total number of ARP requests transmitted from this LEC. |
| C32 atmxLecStatsTxArpRsp | 1.3.6.1.4.1.207.8.9.2.1.1.6.1.1.3 | Counter32 | read-only | Total number of ARP responses transmitted from this LEC. |
| C32 atmxLecStatsTxControlPkts | 1.3.6.1.4.1.207.8.9.2.1.1.6.1.1.4 | Counter32 | read-only | Total number of control packets transmitted from this LEC. |
| C32 atmxLecStatsTxUnicastPkts | 1.3.6.1.4.1.207.8.9.2.1.1.6.1.1.5 | Counter32 | read-only | Total number of unicast packets transmitted from this LEC. |
| C32 atmxLecStatsTxMulticastPkts | 1.3.6.1.4.1.207.8.9.2.1.1.6.1.1.6 | Counter32 | read-only | Total number of multicast packets transmitted from this LEC. |
| C32 atmxLecStatsTxBroadcastPkts | 1.3.6.1.4.1.207.8.9.2.1.1.6.1.1.7 | Counter32 | read-only | Total number of broadcast packets transmitted from this LEC. |
| C32 atmxLecStatsTxDiscardPkts | 1.3.6.1.4.1.207.8.9.2.1.1.6.1.1.8 | Counter32 | read-only | Total number of transmission packets discarded from this LEC. |
| C32 atmxLecStatsRxArpReq | 1.3.6.1.4.1.207.8.9.2.1.1.6.1.1.9 | Counter32 | read-only | Total number of ARP requests received for this LEC. |
| C32 atmxLecStatsRxArpRsp | 1.3.6.1.4.1.207.8.9.2.1.1.6.1.1.10 | Counter32 | read-only | Total number of ARP responses received for this LEC. |
| C32 atmxLecStatsRxControlPkts | 1.3.6.1.4.1.207.8.9.2.1.1.6.1.1.11 | Counter32 | read-only | Total number of control packets received for this LEC. |
| C32 atmxLecStatsRxUnicastPkts | 1.3.6.1.4.1.207.8.9.2.1.1.6.1.1.12 | Counter32 | read-only | Total number of unicast packets received for this LEC. |
| C32 atmxLecStatsRxMulticastPkts | 1.3.6.1.4.1.207.8.9.2.1.1.6.1.1.13 | Counter32 | read-only | Total number of multicast packets received for this LEC. |
| C32 atmxLecStatsRxBroadcastPkts | 1.3.6.1.4.1.207.8.9.2.1.1.6.1.1.14 | Counter32 | read-only | Total number of broadcast packets received for this LEC. |
| C32 atmxLecStatsRxDiscardPkts | 1.3.6.1.4.1.207.8.9.2.1.1.6.1.1.15 | Counter32 | read-only | Total number of discarded packets received for this LEC. |
| atmxCipStatsGroup | 1.3.6.1.4.1.207.8.9.2.1.1.7 | |||
| atmxCipStatsTable | 1.3.6.1.4.1.207.8.9.2.1.1.7.1 | not-accessible | A table of ATM CIP statistics information. | |
| atmxCipStatsEntry | 1.3.6.1.4.1.207.8.9.2.1.1.7.1.1 | not-accessible | An entry in the table, containing information about the CIP statistics. | |
| C32 atmxCipStatsPktsFromOtherLIS | 1.3.6.1.4.1.207.8.9.2.1.1.7.1.1.2 | Counter32 | read-only | Total number of packets received that does not belong to this logical IP subnet. |
| C32 atmxCipStatsTxArpReq | 1.3.6.1.4.1.207.8.9.2.1.1.7.1.1.3 | Counter32 | read-only | Total number of ARP requests transmitted from this CIP. |
| C32 atmxCipStatsTxArpRsp | 1.3.6.1.4.1.207.8.9.2.1.1.7.1.1.4 | Counter32 | read-only | Total number of ARP responses transmitted from this CIP. |
| C32 atmxCipStatsTxInArpReq | 1.3.6.1.4.1.207.8.9.2.1.1.7.1.1.5 | Counter32 | read-only | Total number of InARP requests transmitted from this CIP. |
| C32 atmxCipStatsTxInArpRsp | 1.3.6.1.4.1.207.8.9.2.1.1.7.1.1.6 | Counter32 | read-only | Total number of InARP responses transmitted from this CIP. |
| C32 atmxCipStatsTxDiscards | 1.3.6.1.4.1.207.8.9.2.1.1.7.1.1.7 | Counter32 | read-only | Total number of packets discarded on transmit from this CIP. |
| C32 atmxCipStatsRxArpReq | 1.3.6.1.4.1.207.8.9.2.1.1.7.1.1.8 | Counter32 | read-only | Total number of ARP requests received for this CIP. |
| C32 atmxCipStatsRxArpRsp | 1.3.6.1.4.1.207.8.9.2.1.1.7.1.1.9 | Counter32 | read-only | Total number of ARP responses received for this CIP. |
| C32 atmxCipStatsRxInArpReq | 1.3.6.1.4.1.207.8.9.2.1.1.7.1.1.10 | Counter32 | read-only | Total number of InARP requests received for this CIP. |
| C32 atmxCipStatsRxInArpRsp | 1.3.6.1.4.1.207.8.9.2.1.1.7.1.1.11 | Counter32 | read-only | Total number of InARP responsese received for this CIP. |
| C32 atmxCipStatsRxDiscards | 1.3.6.1.4.1.207.8.9.2.1.1.7.1.1.12 | Counter32 | read-only | Total number of packets discarded on receive for this CIP. |
| atmxSscopStatsGroup | 1.3.6.1.4.1.207.8.9.2.1.1.8 | |||
| atmxSscopStatsTable | 1.3.6.1.4.1.207.8.9.2.1.1.8.1 | not-accessible | A table of ATM Service Specific Connection Oriented Protocol (SSCOP) statistics information. | |
| atmxSscopStatsEntry | 1.3.6.1.4.1.207.8.9.2.1.1.8.1.1 | not-accessible | An entry in the table, containing information about the ATM SSCOP statistics. | |
| C32 atmxSscopStatsTxTotalPdus | 1.3.6.1.4.1.207.8.9.2.1.1.8.1.1.1 | Counter32 | read-only | Total number of transmit PDU's sent without error by SSCOP. |
| C32 atmxSscopStatsTxDiscardSdus | 1.3.6.1.4.1.207.8.9.2.1.1.8.1.1.2 | Counter32 | read-only | Total number of transmit SDUs discarded by SSCOP. |
| C32 atmxSscopStatsTxDiscardPdus | 1.3.6.1.4.1.207.8.9.2.1.1.8.1.1.3 | Counter32 | read-only | Total number of transmit PDUs discarded by SSCOP. |
| C32 atmxSscopStatsTxErrorPdus | 1.3.6.1.4.1.207.8.9.2.1.1.8.1.1.4 | Counter32 | read-only | Total number of transmit PDUs with transmission errors. |
| C32 atmxSscopStatsTxBufferInUseCtr | 1.3.6.1.4.1.207.8.9.2.1.1.8.1.1.5 | Counter32 | read-only | Transmit buffer in-use counter. |
| G32 atmxSscopStatsTxBufferInUseGauge | 1.3.6.1.4.1.207.8.9.2.1.1.8.1.1.6 | Gauge32 | read-only | Transmit buffer in-use gauge. |
| C32 atmxSscopStatsRxTotalPdus | 1.3.6.1.4.1.207.8.9.2.1.1.8.1.1.7 | Counter32 | read-only | Total number of PDU's received without error by SSCOP. |
| C32 atmxSscopStatsRxDiscardPdus | 1.3.6.1.4.1.207.8.9.2.1.1.8.1.1.8 | Counter32 | read-only | Total number of PDUs discarded on receipt by SSCOP. |
| C32 atmxSscopStatsRxErrorPdus | 1.3.6.1.4.1.207.8.9.2.1.1.8.1.1.9 | Counter32 | read-only | Total number of received PDUs with reception errors. |
| C32 atmxSscopStatsRxBufferInUseCtr | 1.3.6.1.4.1.207.8.9.2.1.1.8.1.1.10 | Counter32 | read-only | Receive buffer in-use counter. |
| G32 atmxSscopStatsRxBufferInUseGauge | 1.3.6.1.4.1.207.8.9.2.1.1.8.1.1.11 | Gauge32 | read-only | Receive buffer in-use gauge. |
| atmxIlmiStatsGroup | 1.3.6.1.4.1.207.8.9.2.1.1.9 | |||
| atmxIlmiStatsTable | 1.3.6.1.4.1.207.8.9.2.1.1.9.1 | not-accessible | A table of ATM ILMI statistics information. | |
| atmxIlmiStatsEntry | 1.3.6.1.4.1.207.8.9.2.1.1.9.1.1 | not-accessible | An entry in the table, containing information about the ATM ILMI statistics. | |
| C32 atmxIlmiTxPDUs | 1.3.6.1.4.1.207.8.9.2.1.1.9.1.1.2 | Counter32 | read-only | Total number of transmitted PDUs over the ILMI connection. |
| C32 atmxIlmiRxPDUs | 1.3.6.1.4.1.207.8.9.2.1.1.9.1.1.3 | Counter32 | read-only | Total number of received PDUs over the ILMI connection. |
| C32 atmxIlmiRxDiscardPDUs | 1.3.6.1.4.1.207.8.9.2.1.1.9.1.1.4 | Counter32 | read-only | Total number of received PDUs that are received over the ILMI connection and discarded. |
| atmxVccGroup | 1.3.6.1.4.1.207.8.9.2.1.1.10 | |||
| atmxVccTable | 1.3.6.1.4.1.207.8.9.2.1.1.10.1 | not-accessible | A table of ATM virtual channel connections status and parameter information. | |
| atmxVccEntry | 1.3.6.1.4.1.207.8.9.2.1.1.10.1.1 | not-accessible | An entry in the table, containing information about the ATM virtual channel connections. | |
| ATM atmxVccVpi | 1.3.6.1.4.1.207.8.9.2.1.1.10.1.1.2 | AtmVpi | read-only | The virtual path identifier associated with this virtual connection. |
| ATM atmxVccVci | 1.3.6.1.4.1.207.8.9.2.1.1.10.1.1.3 | AtmVci | not-accessible | The virtual channel identifier associated with the virtual connection. |
| INT atmxVccCircuitType | 1.3.6.1.4.1.207.8.9.2.1.1.10.1.1.4 | INTEGER | read-create | The virtual connection circuit type. |
| ATM atmxVccOperStatus | 1.3.6.1.4.1.207.8.9.2.1.1.10.1.1.5 | AtmConnectionOperStatusCodes | read-only | The actual operational status of the VCC. |
| U32 atmxVccUpTime | 1.3.6.1.4.1.207.8.9.2.1.1.10.1.1.6 | Unsigned32 | read-only | The virtual channel connection up time in seconds since atmxVccOperStatus transitioned to the value 'up'. |
| ATM atmxVccTxQosClass | 1.3.6.1.4.1.207.8.9.2.1.1.10.1.1.7 | AtmQosClass | read-create | Transmit Quality of Service for this virtual channel connection. |
| INT atmxVccTxBestEffort | 1.3.6.1.4.1.207.8.9.2.1.1.10.1.1.8 | INTEGER | read-create | Transmit Best Effort Indicator for this virtual channel connection. |
| INT atmxVccTxPeakCellRate | 1.3.6.1.4.1.207.8.9.2.1.1.10.1.1.9 | INTEGER | read-create | Peak Cell Rate for CLP 0+1 in the transmit direction for this virtual channel connection. |
| ATM atmxVccRxQosClass | 1.3.6.1.4.1.207.8.9.2.1.1.10.1.1.10 | AtmQosClass | read-create | Receive Quality of Service for this virtual channel connection. |
| INT atmxVccRxBestEffort | 1.3.6.1.4.1.207.8.9.2.1.1.10.1.1.11 | INTEGER | read-create | Receive Best Effort Indicator for this virtual channel connection. |
| INT atmxVccRxPeakCellRate | 1.3.6.1.4.1.207.8.9.2.1.1.10.1.1.12 | INTEGER | read-create | Peak Cell Rate for CLP 0+1 in the receive direction for this virtual channel connection. |
| ROW atmxVccRowStatus | 1.3.6.1.4.1.207.8.9.2.1.1.10.1.1.13 | RowStatus | read-create | Only the values 'active', 'createAndGo', and 'delete' are supported. |
| INT atmxVccServiceType | 1.3.6.1.4.1.207.8.9.2.1.1.10.1.1.14 | INTEGER | read-create | The virtual connection Service type. |
| atmxAddressGroup | 1.3.6.1.4.1.207.8.9.2.1.1.11 | |||
| atmxCipArpGroup | 1.3.6.1.4.1.207.8.9.2.1.1.12 | |||
| atmxCipArpTable | 1.3.6.1.4.1.207.8.9.2.1.1.12.1 | not-accessible | A table of ATM address to IP address information. | |
| atmxCipArpEntry | 1.3.6.1.4.1.207.8.9.2.1.1.12.1.1 | not-accessible | An entry in the table, containing information about the ATM address. | |
| IP atmxCipArpIPAddress | 1.3.6.1.4.1.207.8.9.2.1.1.12.1.1.2 | IpAddress | not-accessible | The IP address for this Arp entry. |
| ADR atmxCipArpAtmAddress | 1.3.6.1.4.1.207.8.9.2.1.1.12.1.1.3 | AtmAddress | read-create | The ATM address for the Arp address. |
| ATM atmxCipArpVci | 1.3.6.1.4.1.207.8.9.2.1.1.12.1.1.4 | AtmClientVci | read-create | The virtual channel identifier associated with Arp entry. |
| INT atmxCipArpTimeToLive | 1.3.6.1.4.1.207.8.9.2.1.1.12.1.1.5 | INTEGER | read-only | The Arp Entry time to live in seconds. The value 0 indicates an infinite time to live |
| ATM atmxCipArpSource | 1.3.6.1.4.1.207.8.9.2.1.1.12.1.1.6 | AtmxArpEntryType | read-create | The source of this Arp entry. |
| ROW atmxCipArpRowStatus | 1.3.6.1.4.1.207.8.9.2.1.1.12.1.1.7 | RowStatus | read-create | Only the values 'active', 'createAndGo', and 'delete' are supported. |
| atmxLecArpGroup | 1.3.6.1.4.1.207.8.9.2.1.1.13 | |||
| atmxLecArpTable | 1.3.6.1.4.1.207.8.9.2.1.1.13.1 | not-accessible | A table of ATM address to MAC address information. | |
| atmxLecArpEntry | 1.3.6.1.4.1.207.8.9.2.1.1.13.1.1 | not-accessible | An entry in the table, containing information about the ATM address. | |
| MAC atmxLecArpMacAddress | 1.3.6.1.4.1.207.8.9.2.1.1.13.1.1.2 | MacAddress | not-accessible | The MAC address for identifying this Arp entry. |
| ADR atmxLecArpAtmAddress | 1.3.6.1.4.1.207.8.9.2.1.1.13.1.1.3 | AtmAddress | read-create | The ATM address for the corresponding MAC addess. |
| ATM atmxLecArpVci | 1.3.6.1.4.1.207.8.9.2.1.1.13.1.1.4 | AtmVci | read-create | The virtual channel identifier associated with Arp entry. |
| INT atmxLecArpTimeToLive | 1.3.6.1.4.1.207.8.9.2.1.1.13.1.1.5 | INTEGER | read-only | The address time to live in seconds. The value 0 indicates an infinite time to live. |
| ATM atmxLecArpSource | 1.3.6.1.4.1.207.8.9.2.1.1.13.1.1.6 | AtmxArpEntryType | read-only | The source of this Arp entry. |
| ROW atmxLecArpRowStatus | 1.3.6.1.4.1.207.8.9.2.1.1.13.1.1.7 | RowStatus | read-create | Only the values 'active', 'createAndGo', and 'delete' are supported. |
| atmxPtToPtGroup | 1.3.6.1.4.1.207.8.9.2.1.1.14 | |||
| atmxPtToPtTable | 1.3.6.1.4.1.207.8.9.2.1.1.14.1 | not-accessible | A table of point to point over ATM. | |
| atmxPtToPtEntry | 1.3.6.1.4.1.207.8.9.2.1.1.14.1.1 | not-accessible | An entry in the table containg information about the point to point connection. | |
| INT atmxPtToPtIndex | 1.3.6.1.4.1.207.8.9.2.1.1.14.1.1.1 | INTEGER | not-accessible | The index which identifies each entry instance. |
| STR atmxPtToPtDescription | 1.3.6.1.4.1.207.8.9.2.1.1.14.1.1.2 | DisplayString | read-create | A description of the point to point link. |
| INT atmxPtToPtEncap | 1.3.6.1.4.1.207.8.9.2.1.1.14.1.1.3 | INTEGER | read-create | The data encapsulation format. 'rfc1483' identifies the format defined in RFC 1483. |
| INT atmxPtToPtConnType | 1.3.6.1.4.1.207.8.9.2.1.1.14.1.1.4 | INTEGER | read-create | The connection type of the point to point link. |
| ATM atmxPtToPtVci | 1.3.6.1.4.1.207.8.9.2.1.1.14.1.1.5 | AtmClientVci | read-create | The VCI used if atmxPtToPtConnType has the value 'pvc'. |
| ADR atmxPtToPtDestAddr | 1.3.6.1.4.1.207.8.9.2.1.1.14.1.1.6 | AtmAddress | read-create | The ATM address of the other end point of the connection. |
| ROW atmxPtToPtRowStatus | 1.3.6.1.4.1.207.8.9.2.1.1.14.1.1.7 | RowStatus | read-create | This object is used to create or delete an entry in the atmxPtToPtTable. Only the values 'active', 'createAndGo', and 'delete' are supported. The objects atmxPtToPtVlanNumber, atmxPtToPtConnType, and atmxPtToPtVci if atmxPtToPtConnType is 'pvc' or atmxPtToPtDestAddr if atmxPtToPtConnType is 'svc' are required for a successful 'createAndGo'. |
| IFI atmxPtToPtIfIndex | 1.3.6.1.4.1.207.8.9.2.1.1.14.1.1.8 | IfIndexOrZero | read-only | This is the value of ifIndex or 0 if ifIndex is not known. |
| ATM atmxPtToPtVlanNumber | 1.3.6.1.4.1.207.8.9.2.1.1.14.1.1.9 | AtmxVlanRange | read-create | The VLAN which is supported by this point to point link. |
| ATM atmxPtToPtAdminStatus | 1.3.6.1.4.1.207.8.9.2.1.1.14.1.1.10 | AtmAdminStatus | read-create | The administrative status of this point to point instance. |
| ATM atmxPtToPtOperStatus | 1.3.6.1.4.1.207.8.9.2.1.1.14.1.1.11 | AtmConnectionOperStatusCodes | read-only | The operational status of this point to point instance. |
| atmxPtToPtStatsTable | 1.3.6.1.4.1.207.8.9.2.1.1.14.2 | not-accessible | A table of point to point Statistics. | |
| atmxPtToPtStatsEntry | 1.3.6.1.4.1.207.8.9.2.1.1.14.2.1 | not-accessible | An entry in the table containg information about the point to point connection statistics. | |
| INT atmxPtToPtStatsTotalTxPkts | 1.3.6.1.4.1.207.8.9.2.1.1.14.2.1.1 | INTEGER | read-only | Total Transmission Packets through this Connection. |
| INT atmxPtToPtStatsTotalRxPkts | 1.3.6.1.4.1.207.8.9.2.1.1.14.2.1.2 | INTEGER | read-only | Total Packets Received through this Connection. |
| INT atmxPtToPtStatsTotalTxDiscards | 1.3.6.1.4.1.207.8.9.2.1.1.14.2.1.3 | INTEGER | read-only | Total Transmission packets discarded by this connection. |
| INT atmxPtToPtStatsTotalRxDiscards | 1.3.6.1.4.1.207.8.9.2.1.1.14.2.1.4 | INTEGER | read-only | Total Received packets discarded by this connection. |
| atmxTrunkGroup | 1.3.6.1.4.1.207.8.9.2.1.1.15 | |||
| atmxTrunkTable | 1.3.6.1.4.1.207.8.9.2.1.1.15.1 | not-accessible | A table of trunk over ATM. | |
| atmxTrunkEntry | 1.3.6.1.4.1.207.8.9.2.1.1.15.1.1 | not-accessible | An entry in the table containg information about the trunk connection. | |
| INT atmxTrunkIndex | 1.3.6.1.4.1.207.8.9.2.1.1.15.1.1.1 | INTEGER | not-accessible | The index which identifies each entry instance. |
| STR atmxTrunkDescription | 1.3.6.1.4.1.207.8.9.2.1.1.15.1.1.2 | DisplayString | read-create | A description of the trunk link. |
| INT atmxTrunkConnType | 1.3.6.1.4.1.207.8.9.2.1.1.15.1.1.3 | INTEGER | read-create | The connection type of the trunk link. |
| ATM atmxTrunkVci | 1.3.6.1.4.1.207.8.9.2.1.1.15.1.1.4 | AtmClientVci | read-create | The VCI used if atmxTrunkConnType has the value 'pvc'. |
| ADR atmxTrunkDestAddr | 1.3.6.1.4.1.207.8.9.2.1.1.15.1.1.5 | AtmAddress | read-create | The ATM address of the other end point of the connection if atmxTrunkConnType is 'svc'. |
| ROW atmxTrunkRowStatus | 1.3.6.1.4.1.207.8.9.2.1.1.15.1.1.6 | RowStatus | read-create | This attribute is used to create or delete an entry in the atmxTrunkTable. Only the values 'active', 'createAndGo', and 'delete' are supported. The following objects must exist for a successful create, atmxTrunkConnType and atmxTrunkVci if atmxTrunkConnType has the value 'pvc' or atmxTrunkDestAddr if atmxTrunkConnType has the value 'svc'. |
| ATM atmxTrunkAdminStatus | 1.3.6.1.4.1.207.8.9.2.1.1.15.1.1.7 | AtmAdminStatus | read-create | The administrative status of this trunk instance. |
| ATM atmxTrunkOperStatus | 1.3.6.1.4.1.207.8.9.2.1.1.15.1.1.8 | AtmConnectionOperStatusCodes | read-only | The operational status of this trunk instance. |
| atmxTrunkVlanTable | 1.3.6.1.4.1.207.8.9.2.1.1.15.2 | not-accessible | A table containing the list of 1 or more VLan which are trunked over ATM. Creating an entry in this table creates entries in ifTable and SWITCH-VLAN_MIB.vPortTable. | |
| atmxTrunkVlanEntry | 1.3.6.1.4.1.207.8.9.2.1.1.15.2.1 | not-accessible | An entry in the table identifies each VLAN and the trunk connection. | |
| ATM atmxTrunkVlanNumber | 1.3.6.1.4.1.207.8.9.2.1.1.15.2.1.1 | AtmxVlanRange | not-accessible | This identifies the VLAN whose traffic is carried over the trunk. The value of this object corresponds to vLanNumber defined in the SWITCH-VLAN-MIB module. |
| IFI atmxTrunkVlanIfIndex | 1.3.6.1.4.1.207.8.9.2.1.1.15.2.1.2 | IfIndexOrZero | read-only | This is the value of ifIndex of the Vlan interface. |
| ROW atmxTrunkVlanRowStatus | 1.3.6.1.4.1.207.8.9.2.1.1.15.2.1.3 | RowStatus | read-create | This attribute is used to create or delete an entry in the atmxTrunkTable. Only the values 'active', 'createAndGo', and 'delete' are supported. The corresponding atmTrunkRowStatus must have the value 'active' before this object may be created. |
| atmxTrunkStatsTable | 1.3.6.1.4.1.207.8.9.2.1.1.15.3 | not-accessible | A table of trunk statistics. | |
| atmxTrunkStatsEntry | 1.3.6.1.4.1.207.8.9.2.1.1.15.3.1 | not-accessible | An entry in the table containg information about the trunk connection statistics. | |
| INT atmxTrunkStatsTotalTxPkts | 1.3.6.1.4.1.207.8.9.2.1.1.15.3.1.1 | INTEGER | read-only | Total Transmission Packets through this Connection. |
| INT atmxTrunkStatsTotalRxPkts | 1.3.6.1.4.1.207.8.9.2.1.1.15.3.1.2 | INTEGER | read-only | Total Packets Received through this Connection. |
| INT atmxTrunkStatsTotalTxDiscards | 1.3.6.1.4.1.207.8.9.2.1.1.15.3.1.3 | INTEGER | read-only | Total Transmission packets discarded by this connection. |
| INT atmxTrunkStatsTotalRxDiscards | 1.3.6.1.4.1.207.8.9.2.1.1.15.3.1.4 | INTEGER | read-only | Total Received packets discarded by this connection. |
RFC description
MIB module for ATM switch support with management of virtual path identifiers, VCIs, signaling modes, and related ATM interface configuration.
Start monitoring ATM-capable network switch, legacy ATM transport (interface/virtual-circuit status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.