All MIBs › SONOMASYSTEMS-SONOMA-ATM-IMA-MIB
Category: ATM Interface Management, SonomaSystems ATM WAN Management
Description: Manages SonomaSystems ATM IMA (inverse multiplexing over ATM) group configuration and link status.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is SONOMASYSTEMS-SONOMA-ATM-IMA-MIB?
SONOMASYSTEMS-SONOMA-ATM-IMA-MIB is a vendor-specific MIB from Sonoma Systems, nested under its SONOMASYSTEMS-SONOMA-MIB sonomaATM tree (sonomaImaATMAdapterGroup), that manages ATM Inverse Multiplexing over ATM (IMA) group configuration and per-link status for Sonoma's ATM adapters. Its imaGroupTable, indexed by imaGroupIndex, reports near-end and far-end IMA state (imaGroupNeState, imaGroupFeState), a bitmask imaGroupFailureStatus, group symmetry mode, configured/active transmit and receive link counts (imaGroupNumTxCfgLnks/NumTxActLnks and receive equivalents), timing-reference link selection, and differential-delay measurements (imaGroupDiffDelayMax, imaGroupDiffDelayMaxObs) between bonded links; the companion imaLinkTable reports per-link IMA state indexed by imaLinkIfIndex and imaGroupIndex. This lets an operator confirm that all configured member links of an IMA group are actually active and within acceptable differential delay, since an IMA group with fewer active links than configured runs at reduced bandwidth even though the group itself may still show as up. It depends on SONOMASYSTEMS-SONOMA-MIB for its sonomaATM parent OID and on standard ATM interface indexing for the underlying physical links, and it is deployed on Sonoma Systems ATM access equipment performing IMA bonding. Operators of that equipment can download the SONOMASYSTEMS-SONOMA-ATM-IMA-MIB file to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in SONOMASYSTEMS-SONOMA-ATM-IMA-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Sonoma Systems ATM IMA adapters
Monitoring Examples
An operator polls imaGroupNumTxActLnks against imaGroupNumTxCfgLnks for a given imaGroupIndex to confirm all configured links are active, and checks imaGroupDiffDelayMaxObs against the group's tolerance; a active-link count lower than the configured count, or an imaLinkTable entry showing a link in a failed near-end state, indicates a member link has dropped out of the IMA group and available bandwidth is reduced.
What Can Be Monitored
- IMA group near-end/far-end state
- configured vs. active transmit/receive link counts
- inter-link differential delay measurements
- per-link IMA state and failure status
- group failure status bitmask
This MIB depends on
Related MIBs
Imported Objects
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| sonomaImaATMAdapterGroup | 1.3.6.1.4.1.2926.25.7.7 | |||
| atmImaGroupObjects | 1.3.6.1.4.1.2926.25.7.7.1 | |||
| INT imaGroupNumber | 1.3.6.1.4.1.2926.25.7.7.1.1 | INTEGER | read-only | The number of IMA groups configured on this system. |
| imaGroupTable | 1.3.6.1.4.1.2926.25.7.7.1.2 | not-accessible | The IMA Group Configuration table. | |
| imaGroupEntry | 1.3.6.1.4.1.2926.25.7.7.1.2.1 | not-accessible | An entry in the IMA Group table. | |
| INT imaGroupIndex | 1.3.6.1.4.1.2926.25.7.7.1.2.1.1 | INTEGER | read-only | A unique value for the IMA Group. |
| INT imaGroupRowStatus | 1.3.6.1.4.1.2926.25.7.7.1.2.1.2 | INTEGER | read-write | This object identifies the IMA Group's administrative status. It is used to enable and disable a group. |
| INT imaGroupIfIndex | 1.3.6.1.4.1.2926.25.7.7.1.2.1.3 | INTEGER | read-only | This object identifies the logical interface number ('ifIndex') assigned to this IMA group, and is used to identify corresponding rows in the Interfaces MIB. Note that re-initialization of the management agent may cause a client's 'imaGroupIfIndex' to change. |
| INT imaGroupNeState | 1.3.6.1.4.1.2926.25.7.7.1.2.1.4 | INTEGER | read-only | The current operational state of the near-end IMA Group State Machine. |
| INT imaGroupFeState | 1.3.6.1.4.1.2926.25.7.7.1.2.1.5 | INTEGER | read-only | The current operational state of the far-end IMA Group State Machine. |
| INT imaGroupFailureStatus | 1.3.6.1.4.1.2926.25.7.7.1.2.1.6 | INTEGER | read-only | The current failure status of the IMA group (the reason why the GTSM is in the down state. |
| INT imaGroupSymmetry | 1.3.6.1.4.1.2926.25.7.7.1.2.1.7 | INTEGER | read-write | Symmetry of the IMA group. |
| INT imaGroupMinNumTxLinks | 1.3.6.1.4.1.2926.25.7.7.1.2.1.8 | INTEGER | read-write | Minimum number of transmit links required to be Active for the IMA group to be in the Up state. |
| INT imaGroupMinNumRxLinks | 1.3.6.1.4.1.2926.25.7.7.1.2.1.9 | INTEGER | read-write | Minimum number of receive links required to be Active for the IMA group to be in the Up state. |
| INT imaGroupNeTxClkMode | 1.3.6.1.4.1.2926.25.7.7.1.2.1.10 | INTEGER | read-write | Transmit clocking mode used by the near-end IMA group. |
| INT imaGroupFeTxClkMode | 1.3.6.1.4.1.2926.25.7.7.1.2.1.11 | INTEGER | read-only | Transmit clocking mode used by the far-end IMA group. |
| INT imaGroupTxTimingRefLink | 1.3.6.1.4.1.2926.25.7.7.1.2.1.12 | INTEGER | read-write | The ifIndex of the transmit timing reference link to be used by the near-end for IMA data cell clock recovery from the ATM layer. |
| INT imaGroupRxTimingRefLink | 1.3.6.1.4.1.2926.25.7.7.1.2.1.13 | INTEGER | read-only | The ifIndex of the receive timing reference link to be used by near-end for IMA data cell clock recovery toward the ATM layer. |
| INT imaGroupLastChange | 1.3.6.1.4.1.2926.25.7.7.1.2.1.14 | INTEGER | read-only | The time-of-day the IMA group last changed operational state (i.e., value of imaNeGroupState changed). |
| INT imaGroupTxImaId | 1.3.6.1.4.1.2926.25.7.7.1.2.1.15 | INTEGER | read-write | The IMA ID currently in use by the near-end IMA function. |
| INT imaGroupRxImaId | 1.3.6.1.4.1.2926.25.7.7.1.2.1.16 | INTEGER | read-only | The IMA ID currently in use by the far-end IMA function. |
| INT imaGroupTxFrameLength | 1.3.6.1.4.1.2926.25.7.7.1.2.1.17 | INTEGER | read-write | The frame length to be used by the IMA group in the transmit direction. Can only be set when the IMA group is startup. |
| INT imaGroupRxFrameLength | 1.3.6.1.4.1.2926.25.7.7.1.2.1.18 | INTEGER | read-only | Value of IMA frame length as received from remote IMA function. |
| INT imaGroupDiffDelayMax | 1.3.6.1.4.1.2926.25.7.7.1.2.1.19 | INTEGER | read-write | The maximum number of milliseconds of delay differential among the links that will be tolerated on this interface. |
| INT imaGroupLeastDelayLink | 1.3.6.1.4.1.2926.25.7.7.1.2.1.20 | INTEGER | read-only | The ifIndex of the link configured in the IMA group which has the smallest link propagation delay. This value has meaning only if at least 1 link has been configured in the IMA group. |
| INT imaGroupDiffDelayMaxObs | 1.3.6.1.4.1.2926.25.7.7.1.2.1.21 | INTEGER | read-only | The latest maximum differential delay observed (in milliseconds), i.e. between the links having the least and most link propagation delay, among the receive links that are currently configured in the IMA group. |
| INT imaGroupAlphaValue | 1.3.6.1.4.1.2926.25.7.7.1.2.1.22 | INTEGER | read-write | This indicates the 'alpha' value used to specify the number of consecutive invalid ICP cells to be detected before moving to the IMA HUNT state. |
| INT imaGroupBetaValue | 1.3.6.1.4.1.2926.25.7.7.1.2.1.23 | INTEGER | read-write | This indicates the 'beta' value used to specify the number of consecutive errored ICP cells to be detected before moving to the IMA HUNT state. |
| INT imaGroupGammaValue | 1.3.6.1.4.1.2926.25.7.7.1.2.1.24 | INTEGER | read-write | This indicates the 'gamma' value used to specify the number of consecutive valid ICP cells to be detected before moving to the IMA SYNC state from the PRESYNC state. |
| INT imaGroupRunningSecs | 1.3.6.1.4.1.2926.25.7.7.1.2.1.25 | INTEGER | read-only | The amount of time (in seconds) since this IMA group has been in operation (up or down). |
| INT imaGroupUnavailSecs | 1.3.6.1.4.1.2926.25.7.7.1.2.1.26 | INTEGER | read-only | Count of one second intervals where the IMA Group Traffic State Machine is Down. |
| INT imaGroupNeNumFailures | 1.3.6.1.4.1.2926.25.7.7.1.2.1.27 | INTEGER | read-only | The number of times a near-end group failure (Config-Abort, Insufficient-Links) has been reported since power-up or reboot. |
| INT imaGroupFeNumFailures | 1.3.6.1.4.1.2926.25.7.7.1.2.1.28 | INTEGER | read-only | The number of times a far-end group failure (Config-Abort-FE, Insufficient-Links-FE, Blocked-FE) has been reported since power-up or reboot. This is an optional attribute. |
| INT imaGroupTxAvailCellRate | 1.3.6.1.4.1.2926.25.7.7.1.2.1.29 | INTEGER | read-only | The current cell rate (truncated value in cells per second) provided by this IMA group in the transmit direction, considering all the transmit links in the Active state. |
| INT imaGroupRxAvailCellRate | 1.3.6.1.4.1.2926.25.7.7.1.2.1.30 | INTEGER | read-only | The current cell rate (truncated value in cells per second) provided by this IMA group in the receive direction, considering all the receive links in the Active state. |
| INT imaGroupNumTxCfgLnks | 1.3.6.1.4.1.2926.25.7.7.1.2.1.31 | INTEGER | read-only | The number of links that are configured to transmit in this IMA group. |
| INT imaGroupNumRxCfgLnks | 1.3.6.1.4.1.2926.25.7.7.1.2.1.32 | INTEGER | read-only | The number of links that are configured to receive in this IMA group. |
| INT imaGroupNumTxActLnks | 1.3.6.1.4.1.2926.25.7.7.1.2.1.33 | INTEGER | read-only | The number of links which are configured to transmit and are currently Active in this IMA group. |
| INT imaGroupNumRxActLnks | 1.3.6.1.4.1.2926.25.7.7.1.2.1.34 | INTEGER | read-only | The number of links which are configured to receive and are currently Active in this IMA group. |
| INT imaGroupTestLinkIfIndex | 1.3.6.1.4.1.2926.25.7.7.1.2.1.35 | INTEGER | read-write | This object is used to designate an interface as the Test Link. A value of -1 specifies that the implementation may choose the Test Link. In this case, the implementation may also choose the value of 'imaGroupTestPattern'. |
| INT imaGroupTestPattern | 1.3.6.1.4.1.2926.25.7.7.1.2.1.36 | INTEGER | read-write | The value of this object is used to specify the test pattern in an IMA group loopback operation. A value in the range 0 to 255 designates a specific pattern. A value of -1 specifies that the implementation may choose the value. In this case, the implementation may also choose the value of 'imaGroupTestLinkIfIndex'. |
| INT imaGroupTestProcStatus | 1.3.6.1.4.1.2926.25.7.7.1.2.1.37 | INTEGER | read-write | This object is used to enable or disable the Test Pattern Procedure, and to note whether at least one link failed the test. The test is started by setting operating(2) status. If any link should fail the test, the IMA will set the status to linkfail(3). The linkfail(3) state will persist until either the disabled(1) state is set or until no instance of imaLinkTestProcStatus has the value linkfail(3). Only the values disabled(1) and operating(2) may be written. Writing the operating(2) value will not cause clearing of the linkfail(3) state. |
| atmImaLinkObjects | 1.3.6.1.4.1.2926.25.7.7.2 | |||
| imaLinkTable | 1.3.6.1.4.1.2926.25.7.7.2.1 | not-accessible | The IMA group Link Status and Configuration table. | |
| imaLinkEntry | 1.3.6.1.4.1.2926.25.7.7.2.1.1 | not-accessible | An entry in the IMA Group Link table. | |
| INT imaLinkIfIndex | 1.3.6.1.4.1.2926.25.7.7.2.1.1.1 | INTEGER | read-only | This corresponds to the 'ifIndex' of the MIB-II interface on which this link is established. This object also corresponds to the logical number ('ifIndex') assigned to this IMA link. |
| INT imaLinkRowStatus | 1.3.6.1.4.1.2926.25.7.7.2.1.1.2 | INTEGER | read-write | The imaLinkRowStatus object allows create, change and delete operations on imaLinkTable entries. To create a new conceptual row (or instance) of the imaLinkTable, imaLinkRowStatus must be set to 'createAndWait' or 'createAndGo.' A successful set of the object imaLinkGroupIndex must be performed before the RowStatus of this new row can transition to the 'Active' state. The imaLinkGroupIndex provides the association between a physical IMA link to an IMA group. To change (modify) an imaLinkTable entry, the imaLinkRowStatus object must be set to 'notInService'. Only then can the conceptual row be changed. Setting object imaLinkGroupIndex to a different value has the effect of changing the association between a physical IMA link and an IMA group. To place the link 'in group', the imaLinkRowStatus object is set to 'Active'. While the row is not in 'Active' state, both the Transmit and Receive IMA state machines are in the 'Not In Group' state. To remove (delete) an imaLinkTable entry from this table, set this object to 'destroy.' A network manager may elect to perform a delete operation followed immediately by a create operation instead of a modify operation. The net effect of the delete/create is to re-instantiate (reset) agent counters defined in this table. |
| INT imaLinkGroupIndex | 1.3.6.1.4.1.2926.25.7.7.2.1.1.3 | INTEGER | read-write | The value which identifies the IMA group (imaGroupIndex) of which this link is a member. |
| INT imaLinkNeTxState | 1.3.6.1.4.1.2926.25.7.7.2.1.1.4 | INTEGER | read-only | The current state of the near-end transmit link. |
| INT imaLinkNeRxState | 1.3.6.1.4.1.2926.25.7.7.2.1.1.5 | INTEGER | read-only | The current state of the near-end receive link. |
| INT imaLinkFeTxState | 1.3.6.1.4.1.2926.25.7.7.2.1.1.6 | INTEGER | read-only | The current state of the far-end transmit link as reported via ICP cells. |
| INT imaLinkFeRxState | 1.3.6.1.4.1.2926.25.7.7.2.1.1.7 | INTEGER | read-only | The current state of the far-end receive link as reported via ICP cells. |
| INT imaLinkNeRxFailureStatus | 1.3.6.1.4.1.2926.25.7.7.2.1.1.8 | INTEGER | read-only | The current link failure status of the near-end receive link. |
| INT imaLinkFeRxFailureStatus | 1.3.6.1.4.1.2926.25.7.7.2.1.1.9 | INTEGER | read-only | The current link failure status of the far-end receive link as reported via ICP cells. |
| INT imaLinkTxLid | 1.3.6.1.4.1.2926.25.7.7.2.1.1.10 | INTEGER | read-only | The outgoing LID used currently on the link by the local end. This value has meaning only if the link belongs to an IMA group. |
| INT imaLinkRxLid | 1.3.6.1.4.1.2926.25.7.7.2.1.1.11 | INTEGER | read-only | The incoming LID used currently on the link by the remote end as reported via ICP cells. This value has meaning only if the link belongs to an IMA group. |
| INT imaLinkRelDelay | 1.3.6.1.4.1.2926.25.7.7.2.1.1.12 | INTEGER | read-only | The latest measured delay on this link relative to the link, in the same IMA group, with the least delay. |
| INT imaLinkImaViolations | 1.3.6.1.4.1.2926.25.7.7.2.1.1.13 | INTEGER | read-only | ICP violations: count of errored, invalid or missing ICP cells during non-SES-IMA condition. |
| INT imaLinkOifAnomalies | 1.3.6.1.4.1.2926.25.7.7.2.1.1.14 | INTEGER | read-only | The number of OIF anomalies during non-SES-IMA condition at the near-end. This is an optional attribute. |
| INT imaLinkNeSevErroredSec | 1.3.6.1.4.1.2926.25.7.7.2.1.1.15 | INTEGER | read-only | Count of one second intervals containing several IV-IMA, or one or more link defects (e.g., LOS, OOF/LOF, AIS, LCD), LIF, LODS defects during non-UAS-IMA condition. |
| INT imaLinkFeSevErroredSec | 1.3.6.1.4.1.2926.25.7.7.2.1.1.16 | INTEGER | read-only | Count of one second intervals containing one or more RDI-IMA defects. |
| INT imaLinkNeUnavailSec | 1.3.6.1.4.1.2926.25.7.7.2.1.1.17 | INTEGER | read-only | Count of unavailable seconds at near-end: unavailability begins at the onset of 10 contiguous SES-IMA and ends at the onset of 10 contiguous seconds with no SES-IMA. |
| INT imaLinkFeUnavailSec | 1.3.6.1.4.1.2926.25.7.7.2.1.1.18 | INTEGER | read-only | Count of unavailable seconds at far-end: unavailability begins at the onset of 10 contiguous SES-IMA-FE and ends at the onset of 10 contiguous seconds with no SES-IMA-FE. |
| INT imaLinkNeTxUnusableSec | 1.3.6.1.4.1.2926.25.7.7.2.1.1.19 | INTEGER | read-only | Tx Unusable seconds: count of Unusable seconds at the near end Tx LSM. |
| INT imaLinkNeRxUnusableSec | 1.3.6.1.4.1.2926.25.7.7.2.1.1.20 | INTEGER | read-only | Rx Unusable seconds: count of Unusable seconds at the near end Rx LSM. |
| INT imaLinkFeTxUnusableSec | 1.3.6.1.4.1.2926.25.7.7.2.1.1.21 | INTEGER | read-only | Tx Unusable seconds at far-end: count of seconds with Unusable indications from the far-end Tx LSM. |
| INT imaLinkFeRxUnusableSec | 1.3.6.1.4.1.2926.25.7.7.2.1.1.22 | INTEGER | read-only | Rx Unusable seconds at far-end: count of seconds with Unusable indications from the far-end Rx LSM. |
| INT imaLinkNeTxNumFailures | 1.3.6.1.4.1.2926.25.7.7.2.1.1.23 | INTEGER | read-only | The number of times a near-end transmit failure alarm condition has been entered on this link. |
| INT imaLinkNeRxNumFailures | 1.3.6.1.4.1.2926.25.7.7.2.1.1.24 | INTEGER | read-only | The number of times a near-end receive failure alarm condition has been entered on this link (i.e., LIF, LODS, Mis-Connected, RDI-IMA). |
| INT imaLinkFeTxNumFailures | 1.3.6.1.4.1.2926.25.7.7.2.1.1.25 | INTEGER | read-only | The number of times a far-end transmit failure alarm condition has been entered on this link. This is an optional attribute. |
| INT imaLinkFeRxNumFailures | 1.3.6.1.4.1.2926.25.7.7.2.1.1.26 | INTEGER | read-only | The number of times a far-end receive failure alarm condition has been entered on this link (i.e., LIF, LODS, Mis-Connected, RDI-IMA). This is an optional attribute. |
| INT imaLinkTxStuffs | 1.3.6.1.4.1.2926.25.7.7.2.1.1.27 | INTEGER | read-only | Counts of stuff events inserted in the transmit direction. This is an optional attribute. |
| INT imaLinkRxStuffs | 1.3.6.1.4.1.2926.25.7.7.2.1.1.28 | INTEGER | read-only | Counts of stuff events detected in the receive direction. This is an optional attribute. |
| INT imaLinkRxTestPattern | 1.3.6.1.4.1.2926.25.7.7.2.1.1.29 | INTEGER | read-only | This object identifies the test pattern received in the ICP Cell (octet 17) on the link during the IMA Test Pattern Procedure. This value then may be compared to the transmitted test pattern. |
| INT imaLinkTestProcStatus | 1.3.6.1.4.1.2926.25.7.7.2.1.1.30 | INTEGER | read-only | This value indicates the current state of the Test Pattern Procedure. If the value is disabled(1), the test is not running. A value of operating(2) means the test is running and no error has been found on this interface. A value of linkfail(3) means an error has been detected o this link during the test. Once an error occurs, the linkfail(3) value is latched until either this object is read or until the imaGroupTestProcStatus is moved to disabled(1). Once read, if the error no longer persists, a subsequent read will report the value operating(2). |
| INT imaLinkNumber | 1.3.6.1.4.1.2926.25.7.7.2.1.1.31 | INTEGER | read-only | This corresponds to the link number on the IMA Group. |
| atmImaDs1Objects | 1.3.6.1.4.1.2926.25.7.7.3 | |||
| imaDs1Table | 1.3.6.1.4.1.2926.25.7.7.3.1 | not-accessible | A table of physical layer configuration for the DS1 interface | |
| imaDs1Entry | 1.3.6.1.4.1.2926.25.7.7.3.1.1 | not-accessible | A entry in the table, containing information about the physical layer of a DS1 interface | |
| INT imaDs1Index | 1.3.6.1.4.1.2926.25.7.7.3.1.1.1 | INTEGER | read-only | The physical interface index. |
| INT imaDs1GroupIndex | 1.3.6.1.4.1.2926.25.7.7.3.1.1.2 | INTEGER | read-only | The IMA Group's interface index. |
| INT imaDs1ConfLoopback | 1.3.6.1.4.1.2926.25.7.7.3.1.1.3 | INTEGER | read-write | This object is used to modify the state of internal loopback.... |
| INT imaDs1ConfTxClockSelect | 1.3.6.1.4.1.2926.25.7.7.3.1.1.4 | INTEGER | read-write | Configure the transmit clock. |
| INT imaDs1ConfLineCode | 1.3.6.1.4.1.2926.25.7.7.3.1.1.5 | INTEGER | read-only | Configure the line coding method. |
| INT imaDs1ConfFrameFormat | 1.3.6.1.4.1.2926.25.7.7.3.1.1.6 | INTEGER | read-only | Configure the framing format. |
| INT imaDs1ConfCableLength | 1.3.6.1.4.1.2926.25.7.7.3.1.1.7 | INTEGER | read-write | Configure the cable length. |
| INT imaDs1ConfTxTimingRefLink | 1.3.6.1.4.1.2926.25.7.7.3.1.1.8 | INTEGER | read-only | The ifIndex of the transmit timing reference link to be used by the near-end for IMA data cell clock recovery from the ATM layer. |
| INT imaDs1ConfScramble | 1.3.6.1.4.1.2926.25.7.7.3.1.1.9 | INTEGER | read-only | The cells are scrambled / de-scrambled on the line. |
| CTR imaDs1StatsNoSignals | 1.3.6.1.4.1.2926.25.7.7.3.1.1.10 | Counter | read-only | No signal error counter. |
| CTR imaDs1StatsAISDetects | 1.3.6.1.4.1.2926.25.7.7.3.1.1.11 | Counter | read-only | AIS Detect counter. |
| CTR imaDs1StatsYelAlarmCount | 1.3.6.1.4.1.2926.25.7.7.3.1.1.12 | Counter | read-only | A count of the number of Yellow Alarms. |
| CTR imaDs1StatsLCVErrors | 1.3.6.1.4.1.2926.25.7.7.3.1.1.13 | Counter | read-only | LCV (Line Code Violation) error counter. |
| CTR imaDs1StatsPCVErrors | 1.3.6.1.4.1.2926.25.7.7.3.1.1.14 | Counter | read-only | PCV (Path Code Violation) error counter. |
| CTR imaDs1StatsMOSErrors | 1.3.6.1.4.1.2926.25.7.7.3.1.1.15 | Counter | read-only | Multiframe out of sync error counter. |
| CTR imaDs1StatsSyncLossCount | 1.3.6.1.4.1.2926.25.7.7.3.1.1.16 | Counter | read-only | Sync Loss counter. |
| CTR imaDs1StatsHECErrors | 1.3.6.1.4.1.2926.25.7.7.3.1.1.17 | Counter | read-only | HEC error counter. |
| INT imaDs1StatsSignalLoss | 1.3.6.1.4.1.2926.25.7.7.3.1.1.18 | INTEGER | read-only | Signal loss indication. |
| INT imaDs1StatsAISDetect | 1.3.6.1.4.1.2926.25.7.7.3.1.1.19 | INTEGER | read-only | AIS indication. |
| INT imaDs1StatsYellowAlarm | 1.3.6.1.4.1.2926.25.7.7.3.1.1.20 | INTEGER | read-only | Yellow Alarm indication. |
| INT imaDs1StatsSyncLoss | 1.3.6.1.4.1.2926.25.7.7.3.1.1.21 | INTEGER | read-only | Loss of sync indication. |
| INT imaDs1StatsTxClockLoss | 1.3.6.1.4.1.2926.25.7.7.3.1.1.22 | INTEGER | read-only | Loss of transmit clock indication. |
| CTR imaDs1StatsErrSec | 1.3.6.1.4.1.2926.25.7.7.3.1.1.23 | Counter | read-only | Count of Errored Seconds. |
| CTR imaDs1StatsLineErrSec | 1.3.6.1.4.1.2926.25.7.7.3.1.1.24 | Counter | read-only | Count of Line Errored Seconds. |
| CTR imaDs1StatsErrFreeSec | 1.3.6.1.4.1.2926.25.7.7.3.1.1.25 | Counter | read-only | Count of Error Free Seconds. |
| CTR imaDs1StatsBurstErrSec | 1.3.6.1.4.1.2926.25.7.7.3.1.1.26 | Counter | read-only | Count of Bursty Errored Seconds. |
| CTR imaDs1StatsSevErrSec | 1.3.6.1.4.1.2926.25.7.7.3.1.1.27 | Counter | read-only | Count of Severely Errored Seconds. |
| CTR imaDs1StatsConSevErrSec | 1.3.6.1.4.1.2926.25.7.7.3.1.1.28 | Counter | read-only | Count of Consecutive Severely Errored Seconds. |
| CTR imaDs1StatsFailedSignal | 1.3.6.1.4.1.2926.25.7.7.3.1.1.29 | Counter | read-only | Count of Failed Signal conditions. |
| CTR imaDs1StatsUnavailSec | 1.3.6.1.4.1.2926.25.7.7.3.1.1.30 | Counter | read-only | Count of unavailable secondss. |
| CTR imaDs1StatsSevErrFramSec | 1.3.6.1.4.1.2926.25.7.7.3.1.1.31 | Counter | read-only | Count of Severely Errored Framing Seconds. |
| INT imaDs1StatsClearCounters | 1.3.6.1.4.1.2926.25.7.7.3.1.1.32 | INTEGER | read-write | Clear all counters in this group ONLY. |
| INT imaDs1DebugAddr | 1.3.6.1.4.1.2926.25.7.7.3.1.1.33 | INTEGER | read-write | PCI Phy address for DS1 port register. |
| INT imaDs1DebugReadValue | 1.3.6.1.4.1.2926.25.7.7.3.1.1.34 | INTEGER | read-write | Value read from DS1 port register. |
| INT imaDs1DebugWriteValue | 1.3.6.1.4.1.2926.25.7.7.3.1.1.35 | INTEGER | read-write | Value written to DS1 port register. |
| INT imaDs1DebugRead | 1.3.6.1.4.1.2926.25.7.7.3.1.1.36 | INTEGER | read-write | Read or Write of DS1 port register (TRUE = READ). |
| INT imaDs1PortNumber | 1.3.6.1.4.1.2926.25.7.7.3.1.1.37 | INTEGER | read-only | The port number on the IMA. |
| atmImaE1Objects | 1.3.6.1.4.1.2926.25.7.7.4 | |||
| imaE1Table | 1.3.6.1.4.1.2926.25.7.7.4.1 | not-accessible | A table of physical layer configuration for the E1 interface | |
| imaE1Entry | 1.3.6.1.4.1.2926.25.7.7.4.1.1 | not-accessible | A entry in the table, containing information about the physical layer of a E1 interface | |
| INT imaE1Index | 1.3.6.1.4.1.2926.25.7.7.4.1.1.1 | INTEGER | read-only | The physical interface index. |
| INT imaE1GroupIndex | 1.3.6.1.4.1.2926.25.7.7.4.1.1.2 | INTEGER | read-only | The IMA Group's interface index. |
| INT imaE1ConfLoopback | 1.3.6.1.4.1.2926.25.7.7.4.1.1.3 | INTEGER | read-write | This object is used to modify the state of internal loopback.... |
| INT imaE1ConfTxClockSelect | 1.3.6.1.4.1.2926.25.7.7.4.1.1.4 | INTEGER | read-write | Configure the transmit clock. |
| INT imaE1ConfLineCode | 1.3.6.1.4.1.2926.25.7.7.4.1.1.5 | INTEGER | read-only | Configure the line coding method. |
| INT imaE1ConfFrameFormat | 1.3.6.1.4.1.2926.25.7.7.4.1.1.6 | INTEGER | read-only | Configure the framing format. |
| INT imaE1ConfCableLength | 1.3.6.1.4.1.2926.25.7.7.4.1.1.7 | INTEGER | read-write | Configure Long or Short Haul. |
| INT imaE1ConfTxTimingRefLink | 1.3.6.1.4.1.2926.25.7.7.4.1.1.8 | INTEGER | read-only | The ifIndex of the transmit timing reference link to be used by the near-end for IMA data cell clock recovery from the ATM layer. |
| INT imaE1ConfScramble | 1.3.6.1.4.1.2926.25.7.7.4.1.1.9 | INTEGER | read-only | The cells are scrambled / de-scrambled on the line. |
| CTR imaE1StatsNoSignals | 1.3.6.1.4.1.2926.25.7.7.4.1.1.10 | Counter | read-only | No signal error counter. |
| CTR imaE1StatsRAIDetects | 1.3.6.1.4.1.2926.25.7.7.4.1.1.11 | Counter | read-only | RAI Detect counter. |
| CTR imaE1StatsFASErrors | 1.3.6.1.4.1.2926.25.7.7.4.1.1.12 | Counter | read-only | FAS (Frame Alignment Signal) error counter. |
| CTR imaE1StatsCVErrors | 1.3.6.1.4.1.2926.25.7.7.4.1.1.13 | Counter | read-only | CV (Code Violation) error counter. |
| CTR imaE1StatsCRCErrors | 1.3.6.1.4.1.2926.25.7.7.4.1.1.14 | Counter | read-only | CRC4 error counter. |
| CTR imaE1StatsEBitErrors | 1.3.6.1.4.1.2926.25.7.7.4.1.1.15 | Counter | read-only | E-Bit (FEBE) error counter. |
| CTR imaE1StatsSyncLossCount | 1.3.6.1.4.1.2926.25.7.7.4.1.1.16 | Counter | read-only | Sync Loss counter. |
| CTR imaE1StatsHECErrors | 1.3.6.1.4.1.2926.25.7.7.4.1.1.17 | Counter | read-only | HEC error counter. |
| INT imaE1StatsSignalLoss | 1.3.6.1.4.1.2926.25.7.7.4.1.1.18 | INTEGER | read-only | Signal loss indication. |
| INT imaE1StatsRAIDetect | 1.3.6.1.4.1.2926.25.7.7.4.1.1.19 | INTEGER | read-only | RAI indication. |
| INT imaE1StatsSyncLoss | 1.3.6.1.4.1.2926.25.7.7.4.1.1.20 | INTEGER | read-only | Loss of sync indication. |
| INT imaE1StatsTxClockLoss | 1.3.6.1.4.1.2926.25.7.7.4.1.1.21 | INTEGER | read-only | Loss of transmit clock indication. |
| CTR imaE1StatsErrSec | 1.3.6.1.4.1.2926.25.7.7.4.1.1.22 | Counter | read-only | Count of Errored Seconds. |
| CTR imaE1StatsLineErrSec | 1.3.6.1.4.1.2926.25.7.7.4.1.1.23 | Counter | read-only | Count of Line Errored Seconds. |
| CTR imaE1StatsErrFreeSec | 1.3.6.1.4.1.2926.25.7.7.4.1.1.24 | Counter | read-only | Count of Error Free Seconds. |
| CTR imaE1StatsBurstErrSec | 1.3.6.1.4.1.2926.25.7.7.4.1.1.25 | Counter | read-only | Count of Bursty Errored Seconds. |
| CTR imaE1StatsSevErrSec | 1.3.6.1.4.1.2926.25.7.7.4.1.1.26 | Counter | read-only | Count of Severely Errored Seconds. |
| CTR imaE1StatsConSevErrSec | 1.3.6.1.4.1.2926.25.7.7.4.1.1.27 | Counter | read-only | Count of Consecutive Severely Errored Seconds. |
| CTR imaE1StatsFailedSignal | 1.3.6.1.4.1.2926.25.7.7.4.1.1.28 | Counter | read-only | Count of Failed Signal conditions. |
| CTR imaE1StatsUnavailSec | 1.3.6.1.4.1.2926.25.7.7.4.1.1.29 | Counter | read-only | Count of unavailable secondss. |
| CTR imaE1StatsSevErrFramSec | 1.3.6.1.4.1.2926.25.7.7.4.1.1.30 | Counter | read-only | Count of Severely Errored Framing Seconds. |
| INT imaE1StatsClearCounters | 1.3.6.1.4.1.2926.25.7.7.4.1.1.31 | INTEGER | read-write | Clear all counters in this group ONLY. |
| INT imaE1DebugAddr | 1.3.6.1.4.1.2926.25.7.7.4.1.1.32 | INTEGER | read-write | PCI Phy address for E1 port register. |
| INT imaE1DebugReadValue | 1.3.6.1.4.1.2926.25.7.7.4.1.1.33 | INTEGER | read-write | Value read from E1 port register. |
| INT imaE1DebugWriteValue | 1.3.6.1.4.1.2926.25.7.7.4.1.1.34 | INTEGER | read-write | Value written to E1 port register. |
| INT imaE1DebugRead | 1.3.6.1.4.1.2926.25.7.7.4.1.1.35 | INTEGER | read-write | Read or Write of E1 port register (TRUE = READ). |
| INT imaE1PortNumber | 1.3.6.1.4.1.2926.25.7.7.4.1.1.36 | INTEGER | read-only | The port number on the IMA. |
RFC description
Manages ATM Inverse Multiplexer (IMA) interfaces for Sonoma Systems ATM adapter groups.
Start monitoring Sonoma Systems ATM IMA adapters (IMA group/link bonding status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.