SNANET-MIB

All MIBs › SNANET-MIB

Category: Legacy and Compatibility MIBs, SNA and Legacy WAN Protocols

Description: Manages SNA (Systems Network Architecture) network topology, sessions, and PU/LU resource configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SNANET-MIB?

SNANET-MIB is a vendor-specific MIB, apparently from Unisys, for managing IBM Systems Network Architecture (SNA) network resources on a gateway/node device, covering SNA network topology and node-level configuration. It exposes a type-5 (host/subarea) node table describing domain name, operational state, subarea number, SSCP name/ID, network name, and associated PU (Physical Unit) name, alongside general product-information objects. This MIB is centered on monitoring the software/operational status of SNA network resources: t5nodeOperState in particular reports whether an SNA subarea node is up, down, or in another operational condition, which is the key fault-detection signal for an SNA gateway. It is a self-contained vendor MIB reflecting proprietary SNA gateway implementation rather than an extension of any standard IETF MIB, since SNA management predates and sits outside the TCP/IP MIB framework. It is typically deployed on SNA-to-IP gateway or front-end-processor-class devices bridging legacy mainframe SNA traffic onto modern networks. Engineers can download the SNANET-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SNANET-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Unisys SNA gateway/front-end processor

Monitoring Examples

An operator would poll t5nodeTable/t5nodeEntry, indexed by t5nodeIndex, to check t5nodeOperState for a given SNA node, detecting when a subarea node has gone down or is degraded. t5nodeSscpName, t5nodeSscpId, and t5nodeNetworkName confirm the node is correctly registered with the expected System Services Control Point and SNA network identity. t5nodeDomainName and t5nodePuName would be checked together to confirm a specific SNA domain and Physical Unit are correctly configured and active on the gateway.

What Can Be Monitored

SNA subarea node operational state
SSCP name and ID
SNA network name
domain name
PU (Physical Unit) name

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
TimeTicks
enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
unisys	1.3.6.1.4.1.223
dcp	1.3.6.1.4.1.223.8
snanet	1.3.6.1.4.1.223.8.3
prodInfo	1.3.6.1.4.1.223.8.3.1
STR prodInfoDesc	1.3.6.1.4.1.223.8.3.1.1	DisplayString	read-only	A textual description of the software release. Includes the release level and the internal revision level (example: SNA/net Release 5R2 Revision 5.2.10 Installed 06/03/94 07:10 ).
INT prodInfoFeatures	1.3.6.1.4.1.223.8.3.1.2	INTEGER	read-only	A value which indicates the features included in the software release. The value is a sum. This sum initially takes the value zero, then for each feature a value is assigned corresponding to a power of 2, such that a unique number is generated for each combination of features. Feature 1 Cross-Domain Resource Manager 2 Terminal Connect 4 PU T2.0 Inverted 8 Node Type 2.1 Low Entry Node (len) 16 Network Packet-Switching Interface (NPSI) 32 Remote Batch File Transfer Extended (RBFTE)
t5node	1.3.6.1.4.1.223.8.3.2
t5nodeTable	1.3.6.1.4.1.223.8.3.2.1		not-accessible	This table contains information about the Type 5 node functionality (SSCP) provided by the SNA/net product. Multiple nodes can be provided by a single SNA/net product.
t5nodeEntry	1.3.6.1.4.1.223.8.3.2.1.1		not-accessible	Entry contains information about the Type 5 node functionality (SSCP).
INT t5nodeIndex	1.3.6.1.4.1.223.8.3.2.1.1.1	INTEGER	read-only	SNA/net can appear as more than one t5node. Used to index instances of this object. Value is assigned by the agent and remains constant.
STR t5nodeDomainName	1.3.6.1.4.1.223.8.3.2.1.1.2	DisplayString	read-only	The configured name for this domain. This is also the t5nodeSscpName, if t5nodeSscpName is a 0 length string.
INT t5nodeOperState	1.3.6.1.4.1.223.8.3.2.1.1.3	INTEGER	read-only	The operational state of the Type 5 Domain.
INT t5nodeSubareaNumber	1.3.6.1.4.1.223.8.3.2.1.1.4	INTEGER	read-only	The subarea number for this domain.
STR t5nodeSscpName	1.3.6.1.4.1.223.8.3.2.1.1.5	DisplayString	read-only	The name of the SSCP. Must be unique in the SNA subnetwork. It must match the name of the VTAM CDRM macro that defines this t5node as a CDRM to VTAM. May be a zero length string, in which case, the t5nodeDomainName is the name of the SSCP.
STR t5nodeNetworkName	1.3.6.1.4.1.223.8.3.2.1.1.6	DisplayString	read-only	The SNA network name.
INT t5nodeSscpId	1.3.6.1.4.1.223.8.3.2.1.1.7	INTEGER	read-only	This value is used in ACTCDRM messages sent to VTAM.
STR t5nodePuName	1.3.6.1.4.1.223.8.3.2.1.1.8	DisplayString	read-only	The PU identifier of this node.
t5CdrmTable	1.3.6.1.4.1.223.8.3.2.2		not-accessible	This table contains information about other Crossdomain Resource Managers known to this type 5 node.
t5CdrmEntry	1.3.6.1.4.1.223.8.3.2.2.1		not-accessible	The entry contains information about CDRMs. Variables have read-only access. The variable t5CdrmAdminState has read-write access and is used to control a CDRM.
INT t5CdrmT5nodeIndex	1.3.6.1.4.1.223.8.3.2.2.1.1	INTEGER	read-only	Index in the t5nodetable of the t5node this CDRM is associated with.
STR t5CdrmName	1.3.6.1.4.1.223.8.3.2.2.1.2	DisplayString	read-only	The configured name of the CDRM.
STR t5CdrmSnaName	1.3.6.1.4.1.223.8.3.2.2.1.3	DisplayString	read-only	The name of the CDRM as it is known in the SNA network. May be a zero length string, in which case, the t5CdrmName is the SNA name.
INT t5CdrmType	1.3.6.1.4.1.223.8.3.2.2.1.4	INTEGER	read-only	Identifies the type of CDRM.
INT t5CdrmAdminState	1.3.6.1.4.1.223.8.3.2.2.1.5	INTEGER	read-write	Used by the Management Station to control the CDRM. Values up (2) and down (3) can be read or written, while value other (1) is read-only and indicates that this variable has not been set since reboot.
INT t5CdrmOperState	1.3.6.1.4.1.223.8.3.2.2.1.6	INTEGER	read-only	The current operational state of the CDRM in relation to this Type 5 node SSCP.
INT t5CdrmSubareaNumber	1.3.6.1.4.1.223.8.3.2.2.1.7	INTEGER	read-only	The subarea number for the CDRM.
STR t5CdrmNetworkName	1.3.6.1.4.1.223.8.3.2.2.1.8	DisplayString	read-only	The SNA network name for the CDRM.
INT t5CdrmElementAddress	1.3.6.1.4.1.223.8.3.2.2.1.9	INTEGER	read-only	Element Address assigned to this CDRM.
t5CdrscTable	1.3.6.1.4.1.223.8.3.2.3		not-accessible	This table contains information about other Crossdomain Resources known to this type 5 node.
t5CdrscEntry	1.3.6.1.4.1.223.8.3.2.3.1		not-accessible	The entry contains information about a CDRSC. Variables have read-only access. The variable t5CdrscAdminState has read-write access and is used to control a CDRSC.
INT t5CdrscT5nodeIndex	1.3.6.1.4.1.223.8.3.2.3.1.1	INTEGER	read-only	Index in the t5nodetable of the t5node this CDRSC is associated with.
STR t5CdrscName	1.3.6.1.4.1.223.8.3.2.3.1.2	DisplayString	read-only	The configured name of the CDRSC.
STR t5CdrscSnaName	1.3.6.1.4.1.223.8.3.2.3.1.3	DisplayString	read-only	The name of the CDRSC as it is known in the SNA Network. The SnaName is the same a the t5CdrscName when this value is a zero length string.
STR t5CdrscCdrmName	1.3.6.1.4.1.223.8.3.2.3.1.4	DisplayString	read-only	The name the CDRM which owns this CDRSC.
INT t5CdrscAdminState	1.3.6.1.4.1.223.8.3.2.3.1.5	INTEGER	read-write	Used by the Management Station to control the use of the CDRSC. Values up (2) and down (3) may be read or written, while the value other(1) read-only and indicates this variable has not been set since the last reboot.
INT t5CdrscOperState	1.3.6.1.4.1.223.8.3.2.3.1.6	INTEGER	read-only	The current operational state of the CDRSC in relation to this Type 5 node SSCP.
CTR t5CdrscSessions	1.3.6.1.4.1.223.8.3.2.3.1.7	Counter	read-only	The number of active SNA LU-LU sessions for this CDRSC.
STR t5CdrscDlmName	1.3.6.1.4.1.223.8.3.2.3.1.8	DisplayString	read-only	The name of the Default Logon mode table used by this CDRSC.
STR t5CdrscCosName	1.3.6.1.4.1.223.8.3.2.3.1.9	DisplayString	read-only	The name of the Class of Service table used by this CDRSC.
t5DlmTable	1.3.6.1.4.1.223.8.3.2.4		not-accessible	This table contains information about Default Logon Mode Tables used by the SSCP for LU-LU session establishment.
t5DlmEntry	1.3.6.1.4.1.223.8.3.2.4.1		not-accessible	The entry contains a Default Logon Mode Table entry. All variables are read-only.
INT t5DlmT5nodeIndex	1.3.6.1.4.1.223.8.3.2.4.1.1	INTEGER	read-only	Index in the t5nodetable of the t5node this DLM is associated with.
STR t5DlmName	1.3.6.1.4.1.223.8.3.2.4.1.2	DisplayString	read-only	The configured name of the Default Logon Mode.
STR t5DlmSnaName	1.3.6.1.4.1.223.8.3.2.4.1.3	DisplayString	read-only	The name of the Default Logon Mode as it is known in the SNA network. May contain a zero length string, in which case, the t5DlmName is the SNA name.
OCT t5DlmFmprof	1.3.6.1.4.1.223.8.3.2.4.1.4	OCTET STRING	read-only	The Function Management Profile type, a value from 0 to 18 hexadecimal(byte 1 in the session parameter field).
OCT t5DlmTsprof	1.3.6.1.4.1.223.8.3.2.4.1.5	OCTET STRING	read-only	The Transmission Services profile type, a value from 1 to 17 hexadecimal(byte 2 in the session parameter field).
OCT t5DlmPriprot	1.3.6.1.4.1.223.8.3.2.4.1.6	OCTET STRING	read-only	The primary logical unit protocol, a value from 0 to 0FF hexadecimal(byte 3 in the session parameter field).
OCT t5DlmSecprot	1.3.6.1.4.1.223.8.3.2.4.1.7	OCTET STRING	read-only	The secondary logical unit protocol, a value from 0 to 0FF hexadecimal(byte 4 in the session parameter field).
OCT t5DlmComprot	1.3.6.1.4.1.223.8.3.2.4.1.8	OCTET STRING	read-only	The common logical unit protocol, a value from 0 to 0FFFF hexadecimal(byte 5 and 6 in the session parameter field).
OCT t5DlmRusizes	1.3.6.1.4.1.223.8.3.2.4.1.9	OCTET STRING	read-only	The maximum length of data request units in bytes. A four digit hexadecimal value is provided in the same format as for the ACF/VTAM generation(bytes 9 and 10 in the session parameter field.
OCT t5DlmPservic	1.3.6.1.4.1.223.8.3.2.4.1.10	OCTET STRING	read-only	The logical unit presentation services profile and usage field(bytes 13 through 24 in the session parameter field). A 24 digit hexadecimal number.
OCT t5DlmPsndpac	1.3.6.1.4.1.223.8.3.2.4.1.11	OCTET STRING	read-only	The primary send pacing count(byte 11 in the session parameter field), a value from 0 to 63 decimal.
OCT t5DlmPrcvpac	1.3.6.1.4.1.223.8.3.2.4.1.12	OCTET STRING	read-only	The primary receive pacing count(byte 12 in the session parameter field), a value from 0 to 63 decimal.
OCT t5DlmSsndpac	1.3.6.1.4.1.223.8.3.2.4.1.13	OCTET STRING	read-only	The secondary send pacing count(byte 7 in the session parameter field), a value from 0 to 63 decimal.
OCT t5DlmSrcvpac	1.3.6.1.4.1.223.8.3.2.4.1.14	OCTET STRING	read-only	The secondary receive pacing count(byte 8 in the session parameter field), a value from 0 to 63 decimal.
INT t5DlmEncr	1.3.6.1.4.1.223.8.3.2.4.1.15	INTEGER	read-only	The encryption/decryption type expected by the logical unit(first four bits of byte 26 in the session parameter field), a value from 0 to F hexadecimal.
INT t5DlmBindType	1.3.6.1.4.1.223.8.3.2.4.1.16	INTEGER	read-only	The BIND type, a value of 0 or 1. 0 means a negotiable BIND 1 means a non-negotiable BIND.
STR t5DlmCos	1.3.6.1.4.1.223.8.3.2.4.1.17	DisplayString	read-only	The name of the class of service to be used for a session that uses this logon mode.
t5CosTable	1.3.6.1.4.1.223.8.3.2.5		not-accessible	This table contain class of service (COS) entries.
t5CosEntry	1.3.6.1.4.1.223.8.3.2.5.1		not-accessible	The entry contains a class of service entry. All variables are read-only.
INT t5CosT5nodeIndex	1.3.6.1.4.1.223.8.3.2.5.1.1	INTEGER	read-only	Index in the t5nodetable of the t5node this COS is associated with.
STR t5CosName	1.3.6.1.4.1.223.8.3.2.5.1.2	DisplayString	read-only	The configured name of the class of service entry.
STR t5CosSnaName	1.3.6.1.4.1.223.8.3.2.5.1.3	DisplayString	read-only	The name of the class of service entry as it is known in the SNA Network. May be a zero length string, in which case, the t5CosName is the SNA name.
OCT t5CosVrids	1.3.6.1.4.1.223.8.3.2.5.1.4	OCTET STRING	read-only	A list of virtual routes, in hierarchical order, that are used for LU-LU session traffic. The list is octet pairs in the form x,y where x is the virtual route number from 0 to 7, and y is the transmission priority from 0 to 3. Up to 24 ordered pairs are possible (vr1,tp1 vr2,tp2 ...vr24,tp24).
t5AliasTable	1.3.6.1.4.1.223.8.3.2.6		not-accessible	This table is a crossreference for alias names to SNA/net resource names. The current use of this table is for alternate logon names for Crossdomain resources.
t5AliasEntry	1.3.6.1.4.1.223.8.3.2.6.1		not-accessible	The entry contains the alias name and a reference to the SNA (CDRSC) resource it refers to. All variables are read-only.
INT t5AliasT5nodeIndex	1.3.6.1.4.1.223.8.3.2.6.1.1	INTEGER	read-only	Index in the t5nodetable of the t5node this Alias Name is associated with.
STR t5AliasName	1.3.6.1.4.1.223.8.3.2.6.1.2	DisplayString	read-only	The configured alias name.
OID t5AliasResourceId	1.3.6.1.4.1.223.8.3.2.6.1.3	OBJECT IDENTIFIER	read-only	A reference to the SNA resource (CDRSC) identified by this Alias Name. It is the object identifier representing the instance of the index variable of the resource.
subarea	1.3.6.1.4.1.223.8.3.3
saErTable	1.3.6.1.4.1.223.8.3.3.1		not-accessible	This table contains information about explicit routes between this subarea and other network subareas.
saErEntry	1.3.6.1.4.1.223.8.3.3.1.1		not-accessible	This entry contain information about an explicit route.
INT saErT5nodeIndex	1.3.6.1.4.1.223.8.3.3.1.1.1	INTEGER	read-only	Index in the t5nodetable of the t5node this explicit route is associated with.
INT saErDestinationSubarea	1.3.6.1.4.1.223.8.3.3.1.1.2	INTEGER	read-only	The destination subarea number for this Expicit Route.
INT saErNumber	1.3.6.1.4.1.223.8.3.3.1.1.3	INTEGER	read-only	The number of the Explicit Route.
INT saErTgNumber	1.3.6.1.4.1.223.8.3.3.1.1.4	INTEGER	read-only	The Transmission Group number associated with this Explicit Route.
INT saErOperState	1.3.6.1.4.1.223.8.3.3.1.1.5	INTEGER	read-only	The current operational state of the Explicit Route.
saVrTable	1.3.6.1.4.1.223.8.3.3.2		not-accessible	This table contains information about virtual routes between this subarea and other network subareas. Virtual routes are logical connections between subareas and are mapped to explicit routes.
saVrEntry	1.3.6.1.4.1.223.8.3.3.2.1		not-accessible	This entry contains information about a virtual route. All variables are read-only.
INT saVrT5nodeIndex	1.3.6.1.4.1.223.8.3.3.2.1.1	INTEGER	read-only	Index in the t5nodetable of the t5node this virtual route is associated with.
INT saVrErNumber	1.3.6.1.4.1.223.8.3.3.2.1.2	INTEGER	read-only	The expicit route to which this virtual route belongs.
INT saVrNumber	1.3.6.1.4.1.223.8.3.3.2.1.3	INTEGER	read-only	The number of the Virtual Route.
INT saVrTransmissionPriority	1.3.6.1.4.1.223.8.3.3.2.1.4	INTEGER	read-only	The transmission priority for this virtual route.
INT saVrWindowSize	1.3.6.1.4.1.223.8.3.3.2.1.5	INTEGER	read-only	The initial window size for this virtual route.
INT saVrMinWindowSize	1.3.6.1.4.1.223.8.3.3.2.1.6	INTEGER	read-only	The minimum window size for this virtual route.
INT saVrMaxWindowSize	1.3.6.1.4.1.223.8.3.3.2.1.7	INTEGER	read-only	The maximum window size for this virtual route.
INT saVrPacingCount	1.3.6.1.4.1.223.8.3.3.2.1.8	INTEGER	read-only	The pacing count for this virtual route.
saTransmissionGroup	1.3.6.1.4.1.223.8.3.3.3
saTgTable	1.3.6.1.4.1.223.8.3.3.3.1		not-accessible	This table contains information about transmission groups between this subarea and other network subareas. Entries are dynamically added to this table as they are learned from TG link activations.
saTgEntry	1.3.6.1.4.1.223.8.3.3.3.1.1		not-accessible	This entry contains information about a transmission group.
INT saTgT5nodeIndex	1.3.6.1.4.1.223.8.3.3.3.1.1.1	INTEGER	read-only	Index in the t5nodetable of the t5node this transmission group is associated with.
INT saTgNumber	1.3.6.1.4.1.223.8.3.3.3.1.1.2	INTEGER	read-only	The number of this transmission group.
INT saTgAdjacentSubarea	1.3.6.1.4.1.223.8.3.3.3.1.1.3	INTEGER	read-only	The adjacent subarea number with which this transmission group is associated.
INT saTgOperState	1.3.6.1.4.1.223.8.3.3.3.1.1.4	INTEGER	read-only	The current operational state of this transmission group.
INT saTgMaxSendPiuSize	1.3.6.1.4.1.223.8.3.3.3.1.1.5	INTEGER	read-only	The maximum Path Information Unit size in bytes that may be sent on this Tranmission Group.
INT saTgMaxReceivePiuSize	1.3.6.1.4.1.223.8.3.3.3.1.1.6	INTEGER	read-only	The maximum Path Information Unit size in bytes that may be received on this Tranmission Group.
TIK saTgActiveTime	1.3.6.1.4.1.223.8.3.3.3.1.1.7	TimeTicks	read-only	The value of sysUpTime when this transmission group became active.
TIK saTgLastStateChange	1.3.6.1.4.1.223.8.3.3.3.1.1.8	TimeTicks	read-only	The value of sysUpTime when the last state change occurred.
CTR saTgSentBytes	1.3.6.1.4.1.223.8.3.3.3.1.1.9	Counter	read-only	The number of bytes sent on this transmission group.
CTR saTgReceivedBytes	1.3.6.1.4.1.223.8.3.3.3.1.1.10	Counter	read-only	The number of bytes received on transmission group.
CTR saTgSentBtus	1.3.6.1.4.1.223.8.3.3.3.1.1.11	Counter	read-only	The number of Basic Transmission Units sent on this transmission group.
CTR saTgReceivedBtus	1.3.6.1.4.1.223.8.3.3.3.1.1.12	Counter	read-only	The number of Basic Transmission Units received on this transmission group.
saTgLinkTable	1.3.6.1.4.1.223.8.3.3.3.2		not-accessible	This table contains an entry for each link which may be used for a transmission group. The links are not associated with a transmission group until saTgLinkOperState is active (2).
saTgLinkEntry	1.3.6.1.4.1.223.8.3.3.3.2.1		not-accessible	Contains configuration and state information about TG links. Variables have read-only access. The variable saTgLinkAdminState has read-write access and is used to control a TG link.
INT saTgLinkT5nodeIndex	1.3.6.1.4.1.223.8.3.3.3.2.1.1	INTEGER	read-only	Identifies the Type 5 node with which this transmission group link is associated.
INT saTgLinkIndex	1.3.6.1.4.1.223.8.3.3.3.2.1.2	INTEGER	read-only	Unique index of this transmisson group link. The value is assigned by the agent and is unique among TG and PU links.
INT saTgLinkTgNumber	1.3.6.1.4.1.223.8.3.3.3.2.1.3	INTEGER	read-only	The transmission group number to which this link is associated. Contains a value of zero (0) when saTgLinkOperState is inactive(1).
INT saTgLinkAdjacentSubarea	1.3.6.1.4.1.223.8.3.3.3.2.1.4	INTEGER	read-only	The adjacent subarea number with which this transmission group is associated. Contains a value of zero when saTgLinkOperState in inactive(1).
STR saTgLinkName	1.3.6.1.4.1.223.8.3.3.3.2.1.5	DisplayString	read-only	The administratively assigned name of the transmission group link.
INT saTgLinkOperState	1.3.6.1.4.1.223.8.3.3.3.2.1.6	INTEGER	read-only	The current operational state of this transmission group link.
INT saTgLinkAdminState	1.3.6.1.4.1.223.8.3.3.3.2.1.7	INTEGER	read-write	Used by the Management Station to control the transmission group Link. Values up (2) and down (3) can be read or written, while value other (1) is read-only and indicates that this variable has not been set since reboot.
INT saTgLinkType	1.3.6.1.4.1.223.8.3.3.3.2.1.8	INTEGER	read-only	The type of transmission group link.
OID saTgLinkSpecific	1.3.6.1.4.1.223.8.3.3.3.2.1.9	OBJECT IDENTIFIER	read-only	A row in a table specific for the link. It is the object identifier representing the instance of the index variable in one of the snaLink tables from this MIB.
TIK saTgLinkActiveTime	1.3.6.1.4.1.223.8.3.3.3.2.1.10	TimeTicks	read-only	The value of sysUpTime when this TG link became active.
TIK saTgLinkLastStateChange	1.3.6.1.4.1.223.8.3.3.3.2.1.11	TimeTicks	read-only	The value of sysUptime when the last state change occurred.
CTR saTgLinkSentBytes	1.3.6.1.4.1.223.8.3.3.3.2.1.12	Counter	read-only	The number of bytes sent on this TG link.
CTR saTgLinkReceivedBytes	1.3.6.1.4.1.223.8.3.3.3.2.1.13	Counter	read-only	The number of bytes received on this TG link.
CTR saTgLinkSentBtus	1.3.6.1.4.1.223.8.3.3.3.2.1.14	Counter	read-only	The number of Basic Transmission Units sent on this TG link.
CTR saTgLinkReceivedBtus	1.3.6.1.4.1.223.8.3.3.3.2.1.15	Counter	read-only	The number of Basic Transmission Units received on this TG link.
snaNau	1.3.6.1.4.1.223.8.3.4
t2node	1.3.6.1.4.1.223.8.3.4.1
t2nodeTable	1.3.6.1.4.1.223.8.3.4.1.1		not-accessible	This table contains all configured and dynamic parameters of type 2 nodes have read-only access. There is also one control parameter, t2nodeAdminState which has read-write access. The link specific parameters are contained in a row of a separate table referenced by the snaLinkSpecific object.
t2nodeEntry	1.3.6.1.4.1.223.8.3.4.1.1.1		not-accessible	Entry contains all parameters of one type 2 node. They have read-only access. The entry is created by the Agent. The variable t2nodeAdminState has read-write access and is used to start or stop the node.
INT t2nodeT5nodeIndex	1.3.6.1.4.1.223.8.3.4.1.1.1.1	INTEGER	read-only	Index in the t5nodeTable to which this t2node is associated.
INT t2nodeIndex	1.3.6.1.4.1.223.8.3.4.1.1.1.2	INTEGER	read-only	Used to index the instances of objects assigned by the Agent.
STR t2nodeName	1.3.6.1.4.1.223.8.3.4.1.1.1.3	DisplayString	read-only	The value identifies the name of the Node.
INT t2nodeType	1.3.6.1.4.1.223.8.3.4.1.1.1.4	INTEGER	read-only	This value identifies the type of Node.
STR t2nodeBlockNum	1.3.6.1.4.1.223.8.3.4.1.1.1.5	DisplayString	read-only	The value identifies the block number for this Node instance. It is the first 3 hexadecimal digits of the t2node id.
OCT t2nodeIdNum	1.3.6.1.4.1.223.8.3.4.1.1.1.6	OCTET STRING	read-only	The value identifies the ID number for this Node instance. This is the last 5 hexadecimal digits of the t2node id.
INT t2nodeMaxPiu	1.3.6.1.4.1.223.8.3.4.1.1.1.7	INTEGER	read-only	Maximum number of octets that can be exchanged by this PU in one Pathcontrol Information Unit (PIU).
INT t2nodeLinkType	1.3.6.1.4.1.223.8.3.4.1.1.1.8	INTEGER	read-only	The type of link protocol used for this PU.
OID t2nodeLinkSpecific	1.3.6.1.4.1.223.8.3.4.1.1.1.9	OBJECT IDENTIFIER	read-only	The row in a table specific for the link. It is the object identifier representing the instance of the index variable in one of the snaLink tables from this MIB.
INT t2nodeOperState	1.3.6.1.4.1.223.8.3.4.1.1.1.10	INTEGER	read-only	The operational state of the type 2 Node.
INT t2nodeAdminState	1.3.6.1.4.1.223.8.3.4.1.1.1.11	INTEGER	read-write	The administrative state of the type 2 Node and is used by the Management Station to start or stop the Node. The values that can be read and written are: start (2) - this value has to be used to start, stop (3) - this value has to be used to stop. The values that can be read only are: other (1) - this value indicates that the variable has not been set after reboot.
TIK t2nodeStartTime	1.3.6.1.4.1.223.8.3.4.1.1.1.12	TimeTicks	read-only	The value of sysUpTime at type 2 Node activation.
TIK t2nodeLastStateChange	1.3.6.1.4.1.223.8.3.4.1.1.1.13	TimeTicks	read-only	The value of sysUpTime at the last state change of the type 2 Node.
INT t2nodeActFailureReason	1.3.6.1.4.1.223.8.3.4.1.1.1.14	INTEGER	read-only	The sense code for the activation failure. It will be sent in the trap t2NodeActFailTrap.
t2nodeStatsTable	1.3.6.1.4.1.223.8.3.4.1.2		not-accessible	This table contains the dynamic parameters which have read-only access. The entries in this table augment the entries in the t2nodeTable and cannot be created by Management Station.
t2nodeStatsEntry	1.3.6.1.4.1.223.8.3.4.1.2.1		not-accessible	The entry contains parameters which describe the statistics of one t2node. They have read-only access. The counters represent traffic for all kinds of sessions: LU-LU, SSCP-PU, and SSCP-LU. The entry is created by the Agent.
INT t2nodeStatsT5nodeIndex	1.3.6.1.4.1.223.8.3.4.1.2.1.1	INTEGER	read-only	Index in the t5nodeTable to which this t2node is associated.
INT t2nodeStatsIndex	1.3.6.1.4.1.223.8.3.4.1.2.1.2	INTEGER	read-only	The instance of the entry parameters. The index value is taken by the Agent from t2nodeIndex.
CTR t2nodeStatsSentBytes	1.3.6.1.4.1.223.8.3.4.1.2.1.3	Counter	read-only	The number of bytes sent by this Node.
CTR t2nodeStatsReceivedBytes	1.3.6.1.4.1.223.8.3.4.1.2.1.4	Counter	read-only	The number of bytes received by this Node.
CTR t2nodeStatsSentPius	1.3.6.1.4.1.223.8.3.4.1.2.1.5	Counter	read-only	The number of PIUs sent by this Node.
CTR t2nodeStatsReceivedPius	1.3.6.1.4.1.223.8.3.4.1.2.1.6	Counter	read-only	The number of PIUs received by this Node.
CTR t2nodeStatsSentNegativeResps	1.3.6.1.4.1.223.8.3.4.1.2.1.7	Counter	read-only	The number of negative responses sent by this Node.
CTR t2nodeStatsReceivedNegativeResps	1.3.6.1.4.1.223.8.3.4.1.2.1.8	Counter	read-only	The number of negative responses received by this Node.
GAU t2nodeStatsActiveLus	1.3.6.1.4.1.223.8.3.4.1.2.1.9	Gauge	read-only	The number of LUs currently active on this PU.
GAU t2nodeStatsActLus	1.3.6.1.4.1.223.8.3.4.1.2.1.10	Gauge	read-only	The number of LUs on this type 2 Node which have active SSCP-LU sessions.
GAU t2nodeStatsInActLus	1.3.6.1.4.1.223.8.3.4.1.2.1.11	Gauge	read-only	The number of LUs on this type 2 Node which do not have active SSCP-LU sessions.
GAU t2nodeStatsBindLus	1.3.6.1.4.1.223.8.3.4.1.2.1.12	Gauge	read-only	The number of LUs on this type 2 Node which have received and acknowledged a BIND request.
snaLu	1.3.6.1.4.1.223.8.3.4.2
snaLuTable	1.3.6.1.4.1.223.8.3.4.2.1		not-accessible	This table contains configuration and state information relating to LUs.
snaLuEntry	1.3.6.1.4.1.223.8.3.4.2.1.1		not-accessible	Contains configuration and state objects relating to an LU. All have read-only access with the exeption of snaLuAdminState which has read-write access and is used by the Management station to control the state of the LU.
INT snaLuT5nodeIndex	1.3.6.1.4.1.223.8.3.4.2.1.1.1	INTEGER	read-only	Index in the t5nodeTable to which this LU is associated.
INT snaLuT2nodeIndex	1.3.6.1.4.1.223.8.3.4.2.1.1.2	INTEGER	read-only	Index in the t2nodeTable of the type 2 Node with which this LU is associated.
INT snaLuIndex	1.3.6.1.4.1.223.8.3.4.2.1.1.3	INTEGER	read-only	This value identifies a unique index for an LU instance within a type 2 Node.
STR snaLuName	1.3.6.1.4.1.223.8.3.4.2.1.1.4	DisplayString	read-only	The SNA name for this LU.
INT snaLuType	1.3.6.1.4.1.223.8.3.4.2.1.1.5	INTEGER	read-only	Identifies whether the LU is Type 0, 1, 2, 3 or 6.2
OCT snaLuLocalAddress	1.3.6.1.4.1.223.8.3.4.2.1.1.6	OCTET STRING	read-only	The local address for this LU. It is a byte with a value ranging in size from 0 to 255. For dependent LUs this value ranges from 1 to 255. For independent Lus this value is always 0.
STR snaLuUserName	1.3.6.1.4.1.223.8.3.4.2.1.1.7	DisplayString	read-only	The name of the non-sna terminal or SNA LU that is using this LU. This value does not apply to all LUs and contains a zero length string if not known or does not apply.
STR snaLuPoolName	1.3.6.1.4.1.223.8.3.4.2.1.1.8	DisplayString	read-only	The name of the LU pool to which this LU belongs. An LU Pool is configured by the user. It contains a group of LUs any of which can be assigned to a user requesting an LU by the Pool name. May be a zero length string if this LU does not belong to a pool.
INT snaLuOperState	1.3.6.1.4.1.223.8.3.4.2.1.1.9	INTEGER	read-only	The current operational state of this LU: For dependent LUs active(2) indicates the SSCP-LU session is active. For Independent LUs active(2) indicates that the LU is able to send or receive BINDs.
INT snaLuAdminState	1.3.6.1.4.1.223.8.3.4.2.1.1.10	INTEGER	read-write	This object is used by a management station to control the LU. Values up(2) and down(3) can be read or written, while a value other(1) is read-only and indicates that this variable has not been set since reboot.
TIK snaLuLastStateChange	1.3.6.1.4.1.223.8.3.4.2.1.1.11	TimeTicks	read-only	The value of sysUpTime when the last state change occurred.
TIK snaLuActiveTime	1.3.6.1.4.1.223.8.3.4.2.1.1.12	TimeTicks	read-only	The value of sysUpTime when this LU becomes active.
INT snaLuBindFailureReason	1.3.6.1.4.1.223.8.3.4.2.1.1.13	INTEGER	read-only	The sense code when there is a bind failure.
applicationLu	1.3.6.1.4.1.223.8.3.4.3
applicationLuTable	1.3.6.1.4.1.223.8.3.4.3.1		not-accessible	Table of application LUs configuration and operational information.
appLuEntry	1.3.6.1.4.1.223.8.3.4.3.1.1		not-accessible	Contains configuration and operational variables of an application LU. Variables are read-only with the exception of appLuAdminState which has read-write access and is used by the Management station to control the state of the Application LU.
INT appLuT5nodeIndex	1.3.6.1.4.1.223.8.3.4.3.1.1.1	INTEGER	read-only	Index in the t5nodeTable to which this application LU is associated.
INT appLuIndex	1.3.6.1.4.1.223.8.3.4.3.1.1.2	INTEGER	read-only	Unique index of an application LU.
STR appLuName	1.3.6.1.4.1.223.8.3.4.3.1.1.3	DisplayString	read-only	Configured name for this application LU.
INT appLuConversionType	1.3.6.1.4.1.223.8.3.4.3.1.1.4	INTEGER	read-only	Indicates the type of protocol conversion being performed on behalf of the application LU.
INT appLuHostInterfaceType	1.3.6.1.4.1.223.8.3.4.3.1.1.5	INTEGER	read-only	Identifies the type of application interface used by this application LU.
STR appLuApplicationName	1.3.6.1.4.1.223.8.3.4.3.1.1.6	DisplayString	read-only	The name of the host application which uses this application LU.
STR appLuGatewayName	1.3.6.1.4.1.223.8.3.4.3.1.1.7	DisplayString	read-only	The name of the application gateway. The gateway is used to group application LUs together for management purposes.
INT appLuAdminState	1.3.6.1.4.1.223.8.3.4.3.1.1.8	INTEGER	read-write	Used by the Management Station to control the Application LU. Values up (2) and down (3) can be read or written, while value other (1) is read-only and indicates that this variable has not been set since reboot.
INT appLuOperState	1.3.6.1.4.1.223.8.3.4.3.1.1.9	INTEGER	read-only	The current operational state of this application LU: whether it is inactive, active, or has one of more active sessions.
TIK appLuActiveTime	1.3.6.1.4.1.223.8.3.4.3.1.1.10	TimeTicks	read-only	The value of sysUpTime when this application LU becomes active.
TIK appLuLastStateChange	1.3.6.1.4.1.223.8.3.4.3.1.1.11	TimeTicks	read-only	The value of sysUpTime when the last state change occurred.
INT appLuBindFailureReason	1.3.6.1.4.1.223.8.3.4.3.1.1.12	INTEGER	read-only	The sense code when there is a bind failure.
appLuBatchDeviceTable	1.3.6.1.4.1.223.8.3.4.3.2		not-accessible	Table of configuration information for batch devices associated with a batch type application LU.
appLuBatchDeviceEntry	1.3.6.1.4.1.223.8.3.4.3.2.1		not-accessible	The entry contains configuration variables for batch devices associated with batch type application LUs.
INT appLuBatchDeviceT5nodeIndex	1.3.6.1.4.1.223.8.3.4.3.2.1.1	INTEGER	read-only	Index in the t5nodeTable to which this batch device is associated.
INT appLuBatchDeviceLuIndex	1.3.6.1.4.1.223.8.3.4.3.2.1.2	INTEGER	read-only	The index of an application LU to which this batch device is associated.
STR appLuBatchDeviceName	1.3.6.1.4.1.223.8.3.4.3.2.1.3	DisplayString	read-only	The configured name for this batch device.
INT appLuBatchDeviceType	1.3.6.1.4.1.223.8.3.4.3.2.1.4	INTEGER	read-only	Indicates the type of batch device.
INT appLuBatchDeviceNumber	1.3.6.1.4.1.223.8.3.4.3.2.1.5	INTEGER	read-only	A device number used to identify multiple devices of the same type.
snaSession	1.3.6.1.4.1.223.8.3.5
snaSessionTable	1.3.6.1.4.1.223.8.3.5.1		not-accessible	Table containing dynamic statistics information relating to SNA sessions.
snaSessionEntry	1.3.6.1.4.1.223.8.3.5.1.1		not-accessible	Contains information about an SNA session. Objects in this table have read-only access.
INT snaSessT5nodeIndex	1.3.6.1.4.1.223.8.3.5.1.1.1	INTEGER	read-only	Identifies the Type 5 node which is associated with this SNA session.
STR snaSessNauName	1.3.6.1.4.1.223.8.3.5.1.1.2	DisplayString	read-only	The name of the SNA network addressable unit (NAU).
INT snaSessNauSessNumber	1.3.6.1.4.1.223.8.3.5.1.1.3	INTEGER	read-only	A number identifying the session number within the NAU.
INT snaSessType	1.3.6.1.4.1.223.8.3.5.1.1.4	INTEGER	read-only	Identifies the type of SNA session.
INT snaSessNauElementAddress	1.3.6.1.4.1.223.8.3.5.1.1.5	INTEGER	read-only	The element address assigned to the SNA NAU by the Type 5 node.
INT snaSessState	1.3.6.1.4.1.223.8.3.5.1.1.6	INTEGER	read-only	The state of the session. Valid values for all session types are: initiating (1), terminating (2), and active (4). The value queued (3) is valid only for snaSessType value of lu-lu (2). Some variables are unknown when the session state is initiating (1) or queued (2).
TIK snaSessActiveTime	1.3.6.1.4.1.223.8.3.5.1.1.7	TimeTicks	read-only	The value of sysUpTime when session becomes active.
CTR snaSessSentBytes	1.3.6.1.4.1.223.8.3.5.1.1.8	Counter	read-only	The number of bytes sent on this SNA session.
CTR snaSessReceivedBytes	1.3.6.1.4.1.223.8.3.5.1.1.9	Counter	read-only	The number of bytes received on this session.
CTR snaSessSentRus	1.3.6.1.4.1.223.8.3.5.1.1.10	Counter	read-only	The number of RUs sent on this session.
CTR snaSessReceivedRus	1.3.6.1.4.1.223.8.3.5.1.1.11	Counter	read-only	The number of RUs received on this session.
CTR snaSessSentNegativeResps	1.3.6.1.4.1.223.8.3.5.1.1.12	Counter	read-only	The number of negative responses sent on this session.
CTR snaSessReceivedNegativeResps	1.3.6.1.4.1.223.8.3.5.1.1.13	Counter	read-only	The number of negative responses received on this session.
STR snaSessPartnerNauName	1.3.6.1.4.1.223.8.3.5.1.1.14	DisplayString	read-only	The name of the session partner NAU. May be a zero length string if not known.
INT snaSessPartnerNauSubarea	1.3.6.1.4.1.223.8.3.5.1.1.15	INTEGER	read-only	The subarea number of the session partner NAU. Will be zero if not known.
INT snaSessPartnerNauElementAddress	1.3.6.1.4.1.223.8.3.5.1.1.16	INTEGER	read-only	The element address of the session partner NAU. Will be zero if not known.
INT snaSessVirtualRouteNumber	1.3.6.1.4.1.223.8.3.5.1.1.17	INTEGER	read-only	A value indicating the virtual route number for this session. Will be zero if not known.
INT snaSessTransmissionPriority	1.3.6.1.4.1.223.8.3.5.1.1.18	INTEGER	read-only	A transmission priority for this session. Will be zero if not known.
OCT snaSessProcCorrelationId	1.3.6.1.4.1.223.8.3.5.1.1.19	OCTET STRING	read-only	This variable uniquely identifies this lu-lu session. Will contain a zero length string if snaSessType value is not lu-lu (2).
INT snaSessPluIndicator	1.3.6.1.4.1.223.8.3.5.1.1.20	INTEGER	read-only	It indicates whether LU is primary or secondary for this session. Will be other (1) if snaSessType value is not lu-lu (2).
STR snaSessModeName	1.3.6.1.4.1.223.8.3.5.1.1.21	DisplayString	read-only	The name of the mode used for this session. Contains a zero length string if snaSessType value is not lu-lu (2).
snaLink	1.3.6.1.4.1.223.8.3.6
snaLink802Dot2Table	1.3.6.1.4.1.223.8.3.6.1		not-accessible	This table contains Managed Objects which describe basic configuration parameters for PUs or TGs using 802.2 links.
snaLink802Dot2Entry	1.3.6.1.4.1.223.8.3.6.1.1		not-accessible	Entry contains all link configuration parameters for one PU or TG. The objects in the entry have read-only access.
INT snaLink802Dot2T5nodeIndex	1.3.6.1.4.1.223.8.3.6.1.1.1	INTEGER	read-only	The index of the Type 5 node associated with this link.
INT snaLink802Dot2Index	1.3.6.1.4.1.223.8.3.6.1.1.2	INTEGER	read-only	The index variable assigned by Agent.
OCT snaLink802Dot2SourceAddress	1.3.6.1.4.1.223.8.3.6.1.1.3	OCTET STRING	read-only	Medium Access Control (MAC) address of the source node of this logical link.
INT snaLink802Dot2SourceSAP	1.3.6.1.4.1.223.8.3.6.1.1.4	INTEGER	read-only	The source node's Service Access Point (SSAP).
OCT snaLink802Dot2DestinationAddress	1.3.6.1.4.1.223.8.3.6.1.1.5	OCTET STRING	read-only	Medium Access Control (MAC) address of the destination node of this logical link.
INT snaLink802Dot2DestinationSAP	1.3.6.1.4.1.223.8.3.6.1.1.6	INTEGER	read-only	The Service Access Point used by the remote node (DSAP).
STR snaLink802Dot2MediaType	1.3.6.1.4.1.223.8.3.6.1.1.7	DisplayString	read-only	The underlying physical media type: token-ring or ethernet.
INT snaLink802Dot2Role	1.3.6.1.4.1.223.8.3.6.1.1.8	INTEGER	read-only	The role of the PU used for the 802.2 link.
STR snaLink802Dot2LineName	1.3.6.1.4.1.223.8.3.6.1.1.9	DisplayString	read-only	The configured name of the associated line.
OCT snaLink802Dot2Port	1.3.6.1.4.1.223.8.3.6.1.1.10	OCTET STRING	read-only	The physical port location in the system. The first octet contains the port processor id (0 to 255) and the second octet contains the line number (0-8) for line modules which support multiple lines.
INT snaLink802Dot2IfIndex	1.3.6.1.4.1.223.8.3.6.1.1.11	INTEGER	read-only	The IfIndex value of the interface used by this link.
snaLinkSdlcTable	1.3.6.1.4.1.223.8.3.6.2		not-accessible	This table contains Managed Objects which describe basic configuration parameters for PUs using SDLC link.
snaLinkSdlcEntry	1.3.6.1.4.1.223.8.3.6.2.1		not-accessible	Entry contains all link configuration parameters for one PU. The objects in the entry have read-only access.
INT snaLinkSdlcT5nodeIndex	1.3.6.1.4.1.223.8.3.6.2.1.1	INTEGER	read-only	The index of the Type 5 node associated with this link.
INT snaLinkSdlcIndex	1.3.6.1.4.1.223.8.3.6.2.1.2	INTEGER	read-only	The index variable assigned by Agent.
OCT snaLinkSdlcDestinationStationAddr	1.3.6.1.4.1.223.8.3.6.2.1.3	OCTET STRING	read-only	Station Address (1 byte) of the destination node.
INT snaLinkSdlcStationRole	1.3.6.1.4.1.223.8.3.6.2.1.4	INTEGER	read-only	The role of the local station in relation to a remote one.
STR snaLinkSdlcLineName	1.3.6.1.4.1.223.8.3.6.2.1.5	DisplayString	read-only	The configured name of the associated line.
OCT snaLinkSdlcPort	1.3.6.1.4.1.223.8.3.6.2.1.6	OCTET STRING	read-only	The physical port location in the system. The first octet contains the port processor id (0 to 255) and the second octet contains the line number (0-8) for line modules which support multiple lines.
INT snaLinkSdlcIfIndex	1.3.6.1.4.1.223.8.3.6.2.1.7	INTEGER	read-only	The IfIndex value of the interface used by this link.
snaLinkQllcTable	1.3.6.1.4.1.223.8.3.6.3		not-accessible	This table contains Managed Objects which describe basic configuration parameters for PUs using QLLC links.
snaLinkQllcEntry	1.3.6.1.4.1.223.8.3.6.3.1		not-accessible	Entry contains all link configuration parameters for one PU. The objects in the entry have read-only access.
INT snaLinkQllcT5nodeIndex	1.3.6.1.4.1.223.8.3.6.3.1.1	INTEGER	read-only	The index of the Type 5 node associated with this link.
INT snaLinkQllcIndex	1.3.6.1.4.1.223.8.3.6.3.1.2	INTEGER	read-only	The index variable assigned by Agent.
INT snaLinkQllcLcn	1.3.6.1.4.1.223.8.3.6.3.1.3	INTEGER	read-only	The Logical Channel Number (LCN) used by the source node in the case of SVC. Identifies the Circuit number in the case of PVC.
OCT snaLinkQllcSourceDteAddr	1.3.6.1.4.1.223.8.3.6.3.1.4	OCTET STRING	read-only	The DTE Address (15 bytes) of the source node.
OCT snaLinkQllcDestinationDteAddr	1.3.6.1.4.1.223.8.3.6.3.1.5	OCTET STRING	read-only	The DTE Address (15 bytes) of the destination node.
INT snaLinkQllcRole	1.3.6.1.4.1.223.8.3.6.3.1.6	INTEGER	read-only	The role of the QLLC PU in relation to a remote one.
STR snaLinkQllcPdnGroupName	1.3.6.1.4.1.223.8.3.6.3.1.7	DisplayString	read-only	Name of the associated PDNGROUP.
STR snaLinkQllcLineName	1.3.6.1.4.1.223.8.3.6.3.1.8	DisplayString	read-only	The configured name of the associated line.
OCT snaLinkQllcPort	1.3.6.1.4.1.223.8.3.6.3.1.9	OCTET STRING	read-only	The physical port location in the system. The first octet contains the port processor id (0 to 255) and the second octet contains the line number (0-8) for line modules which support multiple lines.
INT snaLinkQllcIfIndex	1.3.6.1.4.1.223.8.3.6.3.1.10	INTEGER	read-only	The IfIndex value of the interface used by this link.
snaLinkChannelTable	1.3.6.1.4.1.223.8.3.6.4		not-accessible	This table contains Managed Objects which describe basic configuration parameters for PUs using Channel link.
snaLinkChannelEntry	1.3.6.1.4.1.223.8.3.6.4.1		not-accessible	Entry contains all link configuration parameters for one PU. The objects in the entry have read-only access.
INT snaLinkChannelT5nodeIndex	1.3.6.1.4.1.223.8.3.6.4.1.1	INTEGER	read-only	The index of the Type 5 node associated with this link.
INT snaLinkChannelIndex	1.3.6.1.4.1.223.8.3.6.4.1.2	INTEGER	read-only	The index variable assigned by Agent.
STR snaLinkChannelLineName	1.3.6.1.4.1.223.8.3.6.4.1.3	DisplayString	read-only	The configured name of the associated line.
OCT snaLinkChannelPort	1.3.6.1.4.1.223.8.3.6.4.1.4	OCTET STRING	read-only	The physical port location in the system. The first octet contains the port processor id (0 to 255) and the second octet contains the line number (0-8) for line modules which support multiple lines.
INT snaLinkChannelIfIndex	1.3.6.1.4.1.223.8.3.6.4.1.5	INTEGER	read-only	The IfIndex value of the interface used by this link.
snaLinkIntTable	1.3.6.1.4.1.223.8.3.6.5		not-accessible	This table contains Managed Objects which describe basic configuration parameters Internal links.
snaLinkIntEntry	1.3.6.1.4.1.223.8.3.6.5.1		not-accessible	Entry contains all link configuration parameters for one PU. The objects in the entry have read-only access.
INT snaLinkIntT5nodeIndex	1.3.6.1.4.1.223.8.3.6.5.1.1	INTEGER	read-only	The index of the Type 5 node associated with this link.
INT snaLinkIntIndex	1.3.6.1.4.1.223.8.3.6.5.1.2	INTEGER	read-only	The index variable assigned by Agent.
INT snaLinkIntServiceType	1.3.6.1.4.1.223.8.3.6.5.1.3	INTEGER	read-only	The type of the internal link.
INT snaLinkIntOutputCredit	1.3.6.1.4.1.223.8.3.6.5.1.4	INTEGER	read-only	This value is used to control the flow of data on the internal link.
INT snaLinkIntOutputPacing	1.3.6.1.4.1.223.8.3.6.5.1.5	INTEGER	read-only	This value is used to control the flow of data on the internal link.

RFC description

Manages SNA networking on Unisys systems including nodes, sessions, links, and statistics gathering.

Start monitoring Unisys SNA gateway/front-end processor (SNA subarea node operational state) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SNANET-MIB

What Is SNANET-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description