SLE-AM-MIB

All MIBs › SLE-AM-MIB

Last Updated: 2014-02-06

Category: DASAN Networks SLE OLT Management

Description: Manages DASAN Networks OLT access management policies, authentication, and subscriber access control.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SLE-AM-MIB?

SLE-AM-MIB is a DASAN Networks proprietary MIB implementing the Alarm Manager function for their SLE-series GPON/EPON Optical Line Terminal (OLT) platforms used in fiber-access (FTTx) deployments. It exposes alarm-related data covering current and historical alarm conditions, severity, and status across the OLT chassis and its subtending line cards/ports. Its practical use is to monitor the operational and fault status of OLT hardware, surfacing hardware faults, threshold-crossing alarms, and other fault conditions that indicate the real-time health of the access node. It is expected to work alongside other DASAN SLE MIBs (chassis, EPON/GPON, and performance-management modules) that supply the underlying resources whose faults this module reports on. It is typically deployed by broadband/fiber access service providers to centrally monitor alarm and fault state across their OLT fleet. Engineers can download the SLE-AM-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SLE-AM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

DASAN Networks SLE-series OLT (GPON/EPON access node)
fiber access network equipment

Monitoring Examples

An operator would poll the alarm manager's active-alarm table to see currently raised alarms on an SLE OLT chassis, checking severity and status fields to detect faults such as a failed port, power issue, or threshold breach. No concrete sample objects were provided for this module, so specific table/object names cannot be confirmed beyond the general alarm-table/entry pattern typical of DASAN SLE MIBs. A rising count of active high-severity alarms would signal a developing hardware or service problem on the OLT that needs escalation. This MIB is primarily a fault/alarm-status module rather than a general performance-counter MIB.

What Can Be Monitored

active alarm status
alarm severity levels
alarm history
fault/threshold-crossing events

Imported Objects

From DASAN-SMI

sleMgmt

OBJECT-IDENTITY

From SLE-TC-MIB

SleControlRequestResultType
SleControlStatusType

From SNMPv2-SMI

Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32
zeroDotZero

From SNMPv2-TC

TEXTUAL-CONVENTION

OIDs

OID symbolic	OID numeric	Type	Access	Description
sleAlarmMgr	1.3.6.1.4.1.6296.101.15			This MIB contains all needed informations about Alarm Manager.
NTF sleAlarmTrapAlarm	1.3.6.1.4.1.6296.101.15.3.3.2			Notify Alarm Raise/Clear TRAPS to NMS for each entry in the Table
NTF sleAlarmTrapEvent	1.3.6.1.4.1.6296.101.15.3.3.3			Notify Event Occur TRAPS to NMS for each entry in the Table
sleAMAcoBase	1.3.6.1.4.1.6296.101.15.5
NTF sleAMAcoChanged	1.3.6.1.4.1.6296.101.15.5.3.1			Notification for Alarm ACO configuration change
sleAMAcoControl	1.3.6.1.4.1.6296.101.15.5.2
SLE sleAMAcoControlReqResult	1.3.6.1.4.1.6296.101.15.5.2.5	SleControlRequestResultType	read-only	Result of the last command.
INT sleAMAcoControlRequest	1.3.6.1.4.1.6296.101.15.5.2.1	INTEGER	read-write	The configuration commands, and user can configure functions via setting this entry as proper value.
AMA sleAMAcoControlSet	1.3.6.1.4.1.6296.101.15.5.2.6	AMAlarmAco	read-write	ACO control acoOff(1) : buzzer operation enable. acoOn(2) : buzzer operation disable. acoOpr(3) : current buzzer cut.
G32 sleAMAcoControlTimer	1.3.6.1.4.1.6296.101.15.5.2.3	Gauge32	read-write	the wait-time until setRequest end. In case of short-time command, this value is 0
TIK sleAMAcoControlTimeStamp	1.3.6.1.4.1.6296.101.15.5.2.4	TimeTicks	read-only	the time stamp of the last command. (don.t care)
SLE sleAMAcogControlStatus	1.3.6.1.4.1.6296.101.15.5.2.2	SleControlStatusType	read-only	status of user command. User have to check this value as .busy. or .idle. before do setRequest.
AMA sleAMAcoInfo	1.3.6.1.4.1.6296.101.15.5.1.1	AMAlarmAco	read-only	ACO control configuration acoOff(1) : buzzer operation enable. acoOn(2) : buzzer operation disable. acoOpr(3) : current buzzer cut.
sleAMAcoInfoEntry	1.3.6.1.4.1.6296.101.15.5.1
sleAMAcoNotification	1.3.6.1.4.1.6296.101.15.5.3
OCT sleAMAlarmTrapNeId	1.3.6.1.4.1.6296.101.15.1	OCTET STRING	read-only	use for NE idendification when alarm(or event) trap system MAC address
AMA sleAMConfigAlarmClassId	1.3.6.1.4.1.6296.101.15.2.1.1.1	AMAlarmClassId	read-only	Class ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client
AMA sleAMConfigAlarmClearGuardTime	1.3.6.1.4.1.6296.101.15.2.1.1.7	AMAlarmGuardTime	read-only	Alarm clear Soaking time. When any alarm is cleared, this attribute specifies how much time the alarm should be soaked before notifying to Alarm manager range:1 ~ 30, (if '0', no soaking time)
AMT sleAMConfigAlarmEnableState	1.3.6.1.4.1.6296.101.15.2.1.1.5	AMTrapState	read-only	Alarm Trap State. Based on the trap state, the alarm will be notified to NMS. If the TRAP STATE is enabled then the alarm will be notified else wont be notified. enable (1) disabe (0)
AMA sleAMConfigAlarmId	1.3.6.1.4.1.6296.101.15.2.1.1.2	AMAlarmId	read-only	Alarm ID Alarm ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client
INT sleAMConfigAlarmLed	1.3.6.1.4.1.6296.101.15.2.1.1.8	INTEGER	read-write	Alarm led configuration. Determinde led operate or not, when alarms occur. off(0): led not operate on(1) : led operate
OCT sleAMConfigAlarmName	1.3.6.1.4.1.6296.101.15.2.1.1.3	OCTET STRING	read-write	Alarm Name string
AMA sleAMConfigAlarmRaiseGuardTime	1.3.6.1.4.1.6296.101.15.2.1.1.6	AMAlarmGuardTime	read-only	Alarm raise Soaking time. When any alarm is raised, this attribute specifies how much time the alarm should be soaked before notifying to Alarm manager range:1 ~ 30, (if '0', no soaking time)
AMA sleAMConfigAlarmSeverity	1.3.6.1.4.1.6296.101.15.2.1.1.4	AMAlarmSeverity	read-only	Alarm severity: The default severity is pre-defined by each Alarm manager clients critical(1), major(2), minor(3), warning(4), intermediate(5),
sleAMConfigBase	1.3.6.1.4.1.6296.101.15.2
NTF sleAMConfigClearGuardTimeChanged	1.3.6.1.4.1.6296.101.15.2.3.4			Notification for Clear Soak time change
sleAMConfigControl	1.3.6.1.4.1.6296.101.15.2.2
AMA sleAMConfigControlAlarmClassId	1.3.6.1.4.1.6296.101.15.2.2.6	AMAlarmClassId	read-write	Alarm Manager Class ID
AMA sleAMConfigControlAlarmId	1.3.6.1.4.1.6296.101.15.2.2.7	AMAlarmId	read-write	Alarm Manager Alarm Index
AMA sleAMConfigControlClearGuardTime	1.3.6.1.4.1.6296.101.15.2.2.11	AMAlarmGuardTime	read-write	Alarm clear Soaking time. When any alarm is cleared, this attribute specifies how much time the alarm should be soaked before notifying to Alarm manager range:1 ~ 30, (if '0', no soaking time)
AMT sleAMConfigControlEnableState	1.3.6.1.4.1.6296.101.15.2.2.9	AMTrapState	read-write	Alarm Trap State. Based on the trap state, the alarm will be notified to NMS. If the TRAP STATE is enabled then the alarm will be notified else wont be notified. enable (1) disabe (0)
I32 sleAMConfigControlLed	1.3.6.1.4.1.6296.101.15.2.2.12	Integer32	read-write	Alarm led configuration. Determinde led operate or not, when alarms occur. off(0): led not operate on(1) : led operate
AMA sleAMConfigControlRaiseGuardTime	1.3.6.1.4.1.6296.101.15.2.2.10	AMAlarmGuardTime	read-write	Alarm Raise Soaking time. When any alarm is raised, this attribute specifies how much time the alarm should be soaked before notifying to Alarm manager range:1 ~ 30, (if '0', no soaking time)
SLE sleAMConfigControlReqResult	1.3.6.1.4.1.6296.101.15.2.2.5	SleControlRequestResultType	read-only	Result of the last command.
INT sleAMConfigControlRequest	1.3.6.1.4.1.6296.101.15.2.2.1	INTEGER	read-write	The configuration commands, and user can configure functions via setting this entry as proper value.
AMA sleAMConfigControlSeverity	1.3.6.1.4.1.6296.101.15.2.2.8	AMAlarmSeverity	read-write	Alarm Class Severity critical(1), major(2), minor(3), warning(4), ignore(5), default(6)
SLE sleAMConfigControlStatus	1.3.6.1.4.1.6296.101.15.2.2.2	SleControlStatusType	read-only	status of user command. User have to check this value as .busy. or .idle. before do setRequest.
G32 sleAMConfigControlTimer	1.3.6.1.4.1.6296.101.15.2.2.3	Gauge32	read-write	the wait-time until setRequest end. In case of short-time command, this value is 0
TIK sleAMConfigControlTimeStamp	1.3.6.1.4.1.6296.101.15.2.2.4	TimeTicks	read-only	the time stamp of the last command. (don.t care)
NTF sleAMConfigEnableStateChanged	1.3.6.1.4.1.6296.101.15.2.3.2			Notification for Class Trap State change
sleAMConfigEntry	1.3.6.1.4.1.6296.101.15.2.1.1		not-accessible
NTF sleAMConfigLedChanged	1.3.6.1.4.1.6296.101.15.2.3.5			Notification for Alarm led configuration change
sleAMConfigNotification	1.3.6.1.4.1.6296.101.15.2.3
NTF sleAMConfigRaiseGuardTimeChanged	1.3.6.1.4.1.6296.101.15.2.3.3			Notification for Raise Soak time change
NTF sleAMConfigSeverityChanged	1.3.6.1.4.1.6296.101.15.2.3.1			Notification for Alarm severity change
I32 sleAMConfigSpecificId	1.3.6.1.4.1.6296.101.15.2.1.1.9	Integer32	read-write	Alarm Configuration specific ID(4bytes) classId and alarmID are combinded with a specificID * 1st,2nd Bytes - ClassId * 3rd,4th bytes - alarmID
sleAMConfigTable	1.3.6.1.4.1.6296.101.15.2.1		not-accessible	This table is the class Master Alarm table. It gets populated when system init is done. And it contains all the class alarms supported for the device
AMA sleAMCurrentAlarmClassId	1.3.6.1.4.1.6296.101.15.3.1.1.3	AMAlarmClassId	read-only	Class ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client
NTF sleAMCurrentAlarmCleared	1.3.6.1.4.1.6296.101.15.3.3.1			Notification for current alarm clear
AMA sleAMCurrentAlarmId	1.3.6.1.4.1.6296.101.15.3.1.1.4	AMAlarmId	read-only	Alarm ID Alarm ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client
AMA sleAMCurrentAlarmReason	1.3.6.1.4.1.6296.101.15.3.1.1.7	AMAlarmReason	read-only	reasion string
AMA sleAMCurrentAlarmSeverity	1.3.6.1.4.1.6296.101.15.3.1.1.6	AMAlarmSeverity	read-only	Current Alarm Severity: critical(1), major(2), minor(3), warning(4)
AMA sleAMCurrentAlarmSource	1.3.6.1.4.1.6296.101.15.3.1.1.2	AMAlarmSrc	read-only	alarm location infomation \|type\|length\|value\|type\|length\|value\|.... type (1-byte) : alarm location type length(1-byte) : alarm location value length value (length-bytes) : alarm location value
ALA sleAMCurrentAlarmStatus	1.3.6.1.4.1.6296.101.15.3.1.1.5	AlarmStatus	read-only	Current Alarm State: raised (1), masked(2)
sleAMCurrentBase	1.3.6.1.4.1.6296.101.15.3
sleAMCurrentControl	1.3.6.1.4.1.6296.101.15.3.2
SLE sleAMCurrentControlReqResult	1.3.6.1.4.1.6296.101.15.3.2.5	SleControlRequestResultType	read-only	Result of the last command.
INT sleAMCurrentControlRequest	1.3.6.1.4.1.6296.101.15.3.2.1	INTEGER	read-write	The configuration commands, and user can configure functions via setting this entry as proper value. 1: all current alarm clear 2: current alarm clear by SeqId 3: current alarm clear by Source(location)
U32 sleAMCurrentControlSeqId	1.3.6.1.4.1.6296.101.15.3.2.6	Unsigned32	read-write	current alarmControl Sequence ID.(0, all mcurrent alarm cleared) Valid only if the sleAMHistoryControlRequest value is set to 2(alarmHistoryClearBySeqId).
AMA sleAMCurrentControlSource	1.3.6.1.4.1.6296.101.15.3.2.7	AMAlarmSrc	read-write	current alarm clear location infomation \|type\|length\|value\|type\|length\|value\|.... type (1-byte) : alarm location type length(1-byte) : alarm location value length value (length-bytes) : alarm location value
SLE sleAMCurrentControlStatus	1.3.6.1.4.1.6296.101.15.3.2.2	SleControlStatusType	read-only	status of user command. User have to check this value as .busy. or .idle. before do setRequest.
G32 sleAMCurrentControlTimer	1.3.6.1.4.1.6296.101.15.3.2.3	Gauge32	read-write	the wait-time until setRequest end. In case of short-time command, this value is 0
TIK sleAMCurrentControlTimeStamp	1.3.6.1.4.1.6296.101.15.3.2.4	TimeTicks	read-only	the time stamp of the last command. (don.t care)
sleAMCurrentEntry	1.3.6.1.4.1.6296.101.15.3.1.1		not-accessible
sleAMCurrentNotification	1.3.6.1.4.1.6296.101.15.3.3
U32 sleAMCurrentSeqId	1.3.6.1.4.1.6296.101.15.3.1.1.1	Unsigned32	read-only	alarm sequence id key of current alarm table it generated by alarm-manager automatically
INT sleAMCurrentSpecificId	1.3.6.1.4.1.6296.101.15.3.1.1.9	INTEGER	read-write	Current Alarm specific ID(4bytes) classId and alarmID are combinded with a specificID * 1st,2nd Bytes - ClassId * 3rd,4th bytes - alarmID
sleAMCurrentTable	1.3.6.1.4.1.6296.101.15.3.1		not-accessible	This table contains the current active alarms for the Alarm Class. Each Row in this table gets populated when any Alarm is raised
TIK sleAMCurrentTimeAndDate	1.3.6.1.4.1.6296.101.15.3.1.1.8	TimeTicks	read-only	Current Alarm Time and Date
AMA sleAMHistoryAlarmClassId	1.3.6.1.4.1.6296.101.15.4.1.1.3	AMAlarmClassId	read-only	Class ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client
NTF sleAMHistoryAlarmCleared	1.3.6.1.4.1.6296.101.15.4.3.1			Notification for History Class cleared
AMA sleAMHistoryAlarmId	1.3.6.1.4.1.6296.101.15.4.1.1.4	AMAlarmId	read-only	History Alarm ID Alarm ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client
AMA sleAMHistoryAlarmReason	1.3.6.1.4.1.6296.101.15.4.1.1.7	AMAlarmReason	read-write	History alarm Reason string
AMA sleAMHistoryAlarmSeverity	1.3.6.1.4.1.6296.101.15.4.1.1.6	AMAlarmSeverity	read-only	History alarm Severity critical(1), major(2), minor(3), warning(4)
AMA sleAMHistoryAlarmSource	1.3.6.1.4.1.6296.101.15.4.1.1.2	AMAlarmSrc	read-only	\|type\|length\|value\|type\|length\|value\|.... type (1-byte) : alarm location type length(1-byte) : alarm location value length value (length-bytes) : alarm location value
ALA sleAMHistoryAlarmStatus	1.3.6.1.4.1.6296.101.15.4.1.1.5	AlarmStatus	read-only	History Alarm State: cleared (0), raised (1), masked(2)
TIK sleAMHistoryAlarmTimeDate	1.3.6.1.4.1.6296.101.15.4.1.1.8	TimeTicks	read-only	History Alarm Time and Date
sleAMHistoryBase	1.3.6.1.4.1.6296.101.15.4
sleAMHistoryControl	1.3.6.1.4.1.6296.101.15.4.2
SLE sleAMHistoryControlReqResult	1.3.6.1.4.1.6296.101.15.4.2.5	SleControlRequestResultType	read-only	Result of the last command.
INT sleAMHistoryControlRequest	1.3.6.1.4.1.6296.101.15.4.2.1	INTEGER	read-write	The configuration commands, and user can configure functions via setting this entry as proper value. clearAlarmHistory : clears the alarms from the History Table 1: all alarm history clear 2: alarm history clear by SeqId 3: alarm history clear by Source(location)
SLE sleAMHistoryControlStatus	1.3.6.1.4.1.6296.101.15.4.2.2	SleControlStatusType	read-only	status of user command. User have to check this value as .busy. or .idle. before do setRequest.
G32 sleAMHistoryControlTimer	1.3.6.1.4.1.6296.101.15.4.2.3	Gauge32	read-write	the wait-time until setRequest end. In case of short-time command, this value is 0
TIK sleAMHistoryControlTimeStamp	1.3.6.1.4.1.6296.101.15.4.2.4	TimeTicks	read-only	the time stamp of the last command. (don.t care)
U32 sleAMHistoryControSeqId	1.3.6.1.4.1.6296.101.15.4.2.6	Unsigned32	read-write	Alarm History Control Sequence ID. Specify cleared history alarm ID (0, all alarm history cleared)
AMA sleAMHistoryControSource	1.3.6.1.4.1.6296.101.15.4.2.7	AMAlarmSrc	read-write	alarm history clear location infomation Valid only if the sleAMHistoryControlRequest value is set to 3(alarmHistoryClearBySource). \|type\|length\|value\|type\|length\|value\|.... type (1-byte) : alarm location type length(1-byte) : alarm location value length value (length-bytes) : alarm location value
sleAMHistoryEntry	1.3.6.1.4.1.6296.101.15.4.1.1		not-accessible
sleAMHistoryNotification	1.3.6.1.4.1.6296.101.15.4.3
U32 sleAMHistorySeqId	1.3.6.1.4.1.6296.101.15.4.1.1.1	Unsigned32	read-only	Alarm History Sequence ID. This sequence Id is maintained based on the TRAP sent.
I32 sleAMHistorySpecificId	1.3.6.1.4.1.6296.101.15.4.1.1.9	Integer32	read-write	Alarm History specific ID(4bytes) classId and alarmID are combinded with a specificID * 1st,2nd Bytes - ClassId * 3rd,4th bytes - alarmID
sleAMHistoryTable	1.3.6.1.4.1.6296.101.15.4.1		not-accessible	This Table is used to for keeping the Alarm History
sleAMLedBase	1.3.6.1.4.1.6296.101.15.6
NTF sleAMLedChanged	1.3.6.1.4.1.6296.101.15.6.3.1			Notification for LED configuration change
sleAMLedControl	1.3.6.1.4.1.6296.101.15.6.2
SLE sleAMLedControlReqResult	1.3.6.1.4.1.6296.101.15.6.2.5	SleControlRequestResultType	read-only	Result of the last command.
INT sleAMLedControlRequest	1.3.6.1.4.1.6296.101.15.6.2.1	INTEGER	read-write	The configuration commands, and user can configure functions via setting this entry as proper value.
AMA sleAMLedControlSet	1.3.6.1.4.1.6296.101.15.6.2.7	AMAlarmLed	read-write	LED control configuration ledOff(1) : LED operation disable. ledOn(2) : LED operation enable. ledOpr(3) : current LED off.
INT sleAMLedControlSeverity	1.3.6.1.4.1.6296.101.15.6.2.6	INTEGER	read-write	LED Alarm Severity critical(1), major(2), minor(3),
SLE sleAMLedControlStatus	1.3.6.1.4.1.6296.101.15.6.2.2	SleControlStatusType	read-only	status of user command. User have to check this value as .busy. or .idle. before do setRequest.
G32 sleAMLedControlTimer	1.3.6.1.4.1.6296.101.15.6.2.3	Gauge32	read-write	the wait-time until setRequest end. In case of short-time command, this value is 0
TIK sleAMLedControlTimeStamp	1.3.6.1.4.1.6296.101.15.6.2.4	TimeTicks	read-only	the time stamp of the last command. (don.t care)
I32 sleAMLedCount	1.3.6.1.4.1.6296.101.15.6.1.1.3	Integer32	read-write	alarm count of the associated led
sleAMLedEntry	1.3.6.1.4.1.6296.101.15.6.1.1		not-accessible
sleAMLedNotification	1.3.6.1.4.1.6296.101.15.6.3
AMA sleAMLedSet	1.3.6.1.4.1.6296.101.15.6.1.1.2	AMAlarmLed	read-write	ACO control configuration acoOff(1) : buzzer operation enable. acoOn(2) : buzzer operation disable. acoOpr(3) : current buzzer cut.
INT sleAMLedSeverity	1.3.6.1.4.1.6296.101.15.6.1.1.1	INTEGER	read-write	LED Alarm Severity critical(1), major(2), minor(3),
sleAMLedTable	1.3.6.1.4.1.6296.101.15.6.1		not-accessible	This table contains the LED status and configuration.

RFC description

Manages alarms generated by physical entities in the system including chassis, slots, modules, ports, power supplies and fans.

Start monitoring DASAN Networks SLE-series OLT (GPON/EPON access node), fiber access network equipment (alarm manager status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SLE-AM-MIB

What Is SLE-AM-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description