SC5002-MIB

All MIBs › SC5002-MIB

Category: Miscellaneous and Generic MIBs

Description: Defines management objects for the SC5002 series network device configuration and status.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SC5002-MIB?

SC5002-MIB is a General DataComm proprietary MIB (built on the shared GDCMACRO-MIB framework, enterprise OID 498) for the SC5002 data communications equipment, covering firmware version and E1/near-end/far-end alarm configuration. Its version table reports active/stored firmware revision and boot revision with a switch-active-firmware action and downloading-mode indicator, a network-configuration table sets E1 signaling mode, and near-end/far-end alarm-configuration tables record alarm identifier, window, and threshold. As a hardware/software-status MIB it lets an administrator confirm firmware revision and audit near-end/far-end alarm thresholds against the intended circuit-quality tolerance. It is deployed on General DataComm SC5002-series equipment. Engineers can download the SC5002-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SC5002-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

General DataComm SC5002-series equipment

Monitoring Examples

An administrator checks sc5002NearEndAlarmThreshold against the far-end equivalent to confirm consistent alarm sensitivity is configured on both ends of an SC5002 E1 link.

What Can Be Monitored

firmware revision
near-end/far-end alarm thresholds

Imported Objects

From GDCMACRO-MIB

SCinstance

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
dsx1	1.3.6.1.4.1.498.6
gdc	1.3.6.1.4.1.498
sc5002	1.3.6.1.4.1.498.6.8
STR sc5002ActiveFirmwareRev	1.3.6.1.4.1.498.6.8.1.2.1.2	DisplayString	read-only	The version number of the firmware currently executing. The format is MM.NN.BB where: MM: Major Revision (0-99) NN: Minor Revision (0-99) BB: Bug Fix Revision (0-99)
sc5002AlarmData	1.3.6.1.4.1.498.6.8.3.1
sc5002AlarmIndSignal	1.3.6.1.4.1.498.6.8.3.1.9
sc5002Alarms	1.3.6.1.4.1.498.6.8.3
STR sc5002BootRev	1.3.6.1.4.1.498.6.8.1.2.1.4	DisplayString	read-only	The version number of the bootstrap firmware. The version number of the firmware, to allow products to know which revision is installed. The released version number is sequenced from --, A-, ... AA, ... ZZ.
sc5002CurrentFarEnd24HrEntry	1.3.6.1.4.1.498.6.8.6.7.1		not-accessible	An entry in the Current 24 Hr table.
SCI sc5002CurrentFarEnd24HrIndex	1.3.6.1.4.1.498.6.8.6.7.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC5002 to which this entry is applicable. SCinstance is defined to be ssllddcc where: ss (byte value) - physical shelf slot location (01-32) ll (byte value) - line number (01-128) dd (byte value) - drop number (00-31) cc (byte value) - channel or interface number (always 00)
OCT sc5002CurrentFarEnd24HrStat	1.3.6.1.4.1.498.6.8.6.7.1.2	OCTET STRING	read-only	Returns a bitwise map of statistics for the interface in the current 24 hour interval. 1.7 f/u 1.6 f/u 1.5 f/u 1.4 f/u 1.3 f/u 1.2 1: Counter Overflow (>65535) ES 1.1 2^15 1.0 2^14 2.7 f/u 2.6 2^13 ES . 2.0 2^7 3.7 f/u 3.6 2^6 ES . 3.0 2^0 4.7 f/u 4.6 f/u 4.5 f/u 4.4 f/u 4.3 f/u 4.2 1: Counter Overflow (>65535) SES 4.1 2^15 4.0 2^14 5.7 f/u 5.6 2^13 SES . 5.0 2^7 6.7 f/u 6.6 2^6 SES . 6.0 2^0 -- 7.7 f/u 7.6 f/u 7.5 f/u 7.4 f/u 7.3 f/u 7.2 1: Counter Overflow (>65535) BBE 7.1 2^15 7.0 2^14 8.7 f/u 8.6 2^13 BBE . 8.0 2^7 9.7 f/u 9.6 2^6 BBE . 9.0 2^0 10.7 f/u 10.6 f/u 10.5 f/u 10.4 f/u 10.3 f/u 10.2 1: Counter Overflow (>65535) UAS 10.1 2^15 10.0 2^14 11.7 f/u 11.6 2^13 UAS . 11.0 2^7 12.7 f/u 12.6 2^6 UAS . 12.0 2^0
sc5002CurrentFarEnd24HrTable	1.3.6.1.4.1.498.6.8.6.7		not-accessible	The Current 24 Hour table.
INT sc5002DefaultInit	1.3.6.1.4.1.498.6.8.5.1.1.3	INTEGER	read-write	This is used to allow the NonVolatile Configuration to be set to a factory default state. When this value is set to factoryDefault(1) the unit will perform a reset to make the default configuration take effect. The value of normal(2) will be returned when the initialization is complete. The value of normal(2) can not be set by management.
sc5002DiagEntry	1.3.6.1.4.1.498.6.8.4.1.1		not-accessible	The GDC 5002 Diagnostics table entry.
SCI sc5002DiagIndex	1.3.6.1.4.1.498.6.8.4.1.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC5002 to which this entry is applicable. SCinstance is defined to be ssllddcc where: ss (byte value) - physical shelf slot location (01-32) ll (byte value) - line number (01-128) dd (byte value) - drop number (00-31) cc (byte value) - channel or interface number (always 00)
sc5002Diagnostics	1.3.6.1.4.1.498.6.8.4
sc5002DiagRxErr	1.3.6.1.4.1.498.6.8.3.1.2
sc5002DiagTable	1.3.6.1.4.1.498.6.8.4.1		not-accessible	The GDC 5002 Diagnostics table. Information in the entries of this table support diagnostics testing, both active testing via patterns, and passive testing via loopbacks.
INT sc5002DownloadingMode	1.3.6.1.4.1.498.6.8.1.2.1.7	INTEGER	read-write	This object is used to configure the download mode: disableAll(1) Prevents any firmware downloading to SC5002 enableAndWait(2) Allows downloading zipped code to be stored only! enableAndSwitch(3) Allows downloading and then unzips and begins executing the new code
INT sc5002E1SignalingMode	1.3.6.1.4.1.498.6.8.2.1.1.2	INTEGER	read-write	Specifies the channel signaling scheme for the E1 network interface.
sc5002FallbackTimingActive	1.3.6.1.4.1.498.6.8.3.1.10
sc5002FarEndAlarmCfgEntry	1.3.6.1.4.1.498.6.8.3.3.1		not-accessible	An entry in the Far End Alarm Configuration table.
OID sc5002FarEndAlarmCfgIdentifier	1.3.6.1.4.1.498.6.8.3.3.1.2	OBJECT IDENTIFIER	read-only	format: iso.org.dod.internet.private.enterprises.gdc. dsx1.sc5002.sc5002Alarms.sc5002AlarmData.ALM example: 1.3.6.1.4.1.498.6.8.4.1.ALM where ALM = 1 for sc5002NoResponse alarm, 2 for sc5002DiagRxErr alarm, etc., as specified in the Alarm Definitions above.
SCI sc5002FarEndAlarmCfgIndex	1.3.6.1.4.1.498.6.8.3.3.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC5002 to which this entry is applicable. SCinstance is defined to be ssllddcc where: ss (byte value) - physical shelf slot location (01-32) ll (byte value) - line number (01-128) dd (byte value) - drop number (00-31) cc (byte value) - channel or interface number (always 00)
sc5002FarEndAlarmCfgTable	1.3.6.1.4.1.498.6.8.3.3		not-accessible	This table contains entries that configure Far End Alarm reporting.
INT sc5002FarEndAlarmThreshold	1.3.6.1.4.1.498.6.8.3.3.1.4	INTEGER	read-write	The number of events which must be exceed, within the time period specified by the alarm's window, before declaring an alarm
INT sc5002FarEndAlarmWindow	1.3.6.1.4.1.498.6.8.3.3.1.3	INTEGER	read-write	The time period in which a specified number of events must occur, (specified by the alarm's threshold), before declaring an alarm condition. After reporting an Alarm condition and upon expiration of the window time period, the event count is reset to zero and another time period is begun. If the specified number of events is not exceeded within the next time period, an Alarm Cleared condition is reported.
sc5002FarEndBkdBlkErr	1.3.6.1.4.1.498.6.8.3.1.17
sc5002FarEndCurrent15MinEntry	1.3.6.1.4.1.498.6.8.6.5.1		not-accessible	An entry in the sc5002FarEnd Current 15 Minute table.
SCI sc5002FarEndCurrent15MinIndex	1.3.6.1.4.1.498.6.8.6.5.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC5002 to which this entry is applicable. SCinstance is defined to be ssllddcc where: ss (byte value) - physical shelf slot location (01-32) ll (byte value) - line number (01-128) dd (byte value) - drop number (00-31) cc (byte value) - channel or interface number (always 00)
OCT sc5002FarEndCurrent15MinStat	1.3.6.1.4.1.498.6.8.6.5.1.2	OCTET STRING	read-only	Returns a bitwise map of the far end interface in one of the previous 16, individual 15 minute, intervals. 1.7 f/u 1.6 f/u 1.5 f/u 1.4 f/u 1.3 f/u 1.2 2^9 ES . 1.0 2^7 2.7 f/u 2.6 2^6 . 2.0 2^0 3.7 f/u 3.6 f/u 3.5 f/u 3.4 f/u 3.3 f/u 3.2 2^9 SES . 3.0 2^7 4.7 f/u 4.6 2^6 SES . 4.0 2^0 5.7 f/u 5.6 f/u 5.5 f/u 5.4 f/u 5.3 f/u 5.2 Counter Overflow (>65535) BBE 5.1 2^15 5.0 2^14 6.7 f/u 6.6 2^13 BBE . 6.0 2^7 7.7 f/u 7.6 2^6 BBE . 7.0 2^0 -- 8.7 f/u 8.6 f/u 8.5 f/u 8.4 f/u 8.3 f/u 8.2 2^9 UAS . 8.0 2^7 9.7 f/u 9.6 2^6 UAS . 9.0 2^0
sc5002FarEndCurrent15MinTable	1.3.6.1.4.1.498.6.8.6.5		not-accessible	The sc5002FarEnd Current 15 minute table.
sc5002FarEndErrSec	1.3.6.1.4.1.498.6.8.3.1.16
sc5002FarEndIntervalEntry	1.3.6.1.4.1.498.6.8.6.6.1		not-accessible	An entry in the Interval table.
SCI sc5002FarEndIntervalIndex	1.3.6.1.4.1.498.6.8.6.6.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC5002 to which this entry is applicable. SCinstance is defined to be ssllddcc where: ss (byte value) - physical shelf slot location (01-32) ll (byte value) - line number (01-128) dd (byte value) - drop number (00-31) cc (byte value) - channel or interface number (always 00)
INT sc5002FarEndIntervalNumber	1.3.6.1.4.1.498.6.8.6.6.1.2	INTEGER	read-only	A number between 1 and 16, where 1 is the most recently completed 15 minute interval and 16 is the least recently completed 15 minutes interval (assuming that all 16 intervals are valid).
OCT sc5002FarEndIntervalStat	1.3.6.1.4.1.498.6.8.6.6.1.3	OCTET STRING	read-only	Returns a bitwise map of statistics for the far end interface in the current 15 minute interval. 1.7 f/u 1.6 f/u 1.5 f/u 1.4 f/u 1.3 f/u 1.2 2^9 ES . 1.0 2^7 2.7 f/u 2.6 2^6 . 2.0 2^0 3.7 f/u 3.6 f/u 3.5 f/u 3.4 f/u 3.3 f/u 3.2 2^9 SES . 3.0 2^7 4.7 f/u 4.6 2^6 SES . 4.0 2^0 5.7 f/u 5.6 f/u 5.5 f/u 5.4 f/u 5.3 f/u 5.2 Counter Overflow (>65535) BBE 5.1 2^15 5.0 2^14 6.7 f/u 6.6 2^13 BBE . 6.0 2^7 7.7 f/u 7.6 2^6 BBE . 7.0 2^0 8.7 f/u 8.6 f/u 8.5 f/u 8.4 f/u 8.3 f/u 8.2 2^9 UAS . 8.0 2^7 9.7 f/u 9.6 2^6 UAS . 9.0 2^0
sc5002FarEndIntervalTable	1.3.6.1.4.1.498.6.8.6.6		not-accessible	The sc5002FarEnd Interval table.
INT sc5002FarEndResetStats	1.3.6.1.4.1.498.6.8.5.1.1.6	INTEGER	read-write	Supports the action of soft resetting the sc5002FarEndValidIntervals object. When this object is set to reset(2), then the unit will reset the sc5002ValidIntervals object to zero. The value of norm(1) can not be set by management.
sc5002FarEndSevErrSec	1.3.6.1.4.1.498.6.8.3.1.18
INT sc5002FarEndStatLastInitialized	1.3.6.1.4.1.498.6.8.5.1.1.7	INTEGER	read-only	Number of seconds from midnight Dec 31, 1969 up until sc5002FarEndValidIntervals was last initialized to zero
sc5002FarEndUnavailableTimeRegEntry	1.3.6.1.4.1.498.6.8.6.10.1		not-accessible	An entry in the Unavailable Time Register table.
SCI sc5002FarEndUnavailableTimeRegIndex	1.3.6.1.4.1.498.6.8.6.10.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC5002 to which this entry is applicable. SCinstance is defined to be ssllddcc where: ss (byte value) - physical shelf slot location (01-32) ll (byte value) - line number (01-128) dd (byte value) - drop number (00-31) cc (byte value) - channel or interface number (always 00)
INT sc5002FarEndUnavailableTimeRegNumber	1.3.6.1.4.1.498.6.8.6.10.1.2	INTEGER	read-only	A number between 1 and 6, where the number is the number of the Unavailable Time Register.
INT sc5002FarEndUnavailableTimeRegStart	1.3.6.1.4.1.498.6.8.6.10.1.3	INTEGER	read-only	Start time of one of the Unavailable Time Registers.
INT sc5002FarEndUnavailableTimeRegStop	1.3.6.1.4.1.498.6.8.6.10.1.4	INTEGER	read-only	Stop time of one of the Unavailable Time Registers.
sc5002FarEndUnavailableTimeRegTable	1.3.6.1.4.1.498.6.8.6.10		not-accessible	The sc5002 Unavailable Time Register table.
sc5002FarEndUnavlSec	1.3.6.1.4.1.498.6.8.3.1.19
INT sc5002FarEndValidIntervals	1.3.6.1.4.1.498.6.8.5.1.1.10	INTEGER	read-only	The number of previous intervals for which valid data was collected. The value will be 16 unless the interface was brought on-line within the last 4 hours, in which case the value will be the number of complete 15 minute intervals the since interface has been online.
STR sc5002FirmwareRev	1.3.6.1.4.1.498.6.8.1.2.1.8	DisplayString	read-only	The version number of the firmware. Released versions are sequenced from --, A-, ... AA, ... ZZ. Test versions are from 01 to 99.
OCT sc5002LedStatus	1.3.6.1.4.1.498.6.8.5.1.1.8	OCTET STRING	read-only	Returns a bitwise snapshot of the front panel LED state. Octet 1 bit 7 - not used bit 6 - ON bit 5 - INSV bit 4 - RSP bit 3 - TMG bit 2 - NIU bit 1 - D_I bit 0 - future use Octet 2 bit 7 - not used bit 6 - future use bit 5 - NTWK AIS bit 4 - NTWK LCV bit 3 - NTWK LOS bit 2 - NTWK OOF bit 1 - ALM bit 0 - TM Octet 3 bit 7 - not used bit 6 - ST- future use bit 5 - LT- future use bit 4 - RL- future use bit 3 - TM transitions/flashing bit 2 - future use bit 1 - future use bit 0 - future use
INT sc5002LoopbackConfig	1.3.6.1.4.1.498.6.8.4.1.1.2	INTEGER	read-write	Selects the test to run. A get of this object returns the test that is currently running. A set of noLoopBack(1) ends the test that is currently running. A set of lineLoopBack(2) starts a line loop back test. The line loop back test runs until a set of noLoopBack(1) is sent. A set of unitTest(3) starts a unit test. The unit test runs for 15 seconds.
sc5002LossOfFrame	1.3.6.1.4.1.498.6.8.3.1.8
sc5002LossOfSignal	1.3.6.1.4.1.498.6.8.3.1.7
sc5002Maintenance	1.3.6.1.4.1.498.6.8.5
sc5002MaintenanceEntry	1.3.6.1.4.1.498.6.8.5.1.1		not-accessible	An entry in the GDC E1 Maintenance Table.
SCI sc5002MaintenanceLineIndex	1.3.6.1.4.1.498.6.8.5.1.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC5002 to which this entry is applicable. SCinstance is defined to be ssllddcc where: ss (byte value) - physical shelf slot location (01-32) ll (byte value) - line number (01-128) dd (byte value) - drop number (00-31) cc (byte value) - channel or interface number (always 00)
sc5002MaintenanceTable	1.3.6.1.4.1.498.6.8.5.1		not-accessible	The table describes the maintenance objects for the unit and references the unit interface (cc = 00).
STR sc5002MIBversion	1.3.6.1.4.1.498.6.8.1.1	DisplayString	read-only	Identifies the version of the MIB. The format of the version is x.yzT, where 'x' identifies the major revision number, 'y' identifies the minor revision number, 'z' identifies the typographical revision, and T identifies the test revision. Upon formal release, no designation for the test revision will be present. Acceptable values for the individual revision components are as follows: x: 1 - 9, y: 0 - 9, z: 0 - 9, T: A - Z
sc5002NearEndAlarmCfgEntry	1.3.6.1.4.1.498.6.8.3.2.1		not-accessible	An entry in the Near End Alarm Configuration table.
OID sc5002NearEndAlarmCfgIdentifier	1.3.6.1.4.1.498.6.8.3.2.1.2	OBJECT IDENTIFIER	read-only	format: iso.org.dod.internet.private.enterprises.gdc. dsx1.sc5002.sc5002Alarms.sc5002AlarmData.ALM example: 1.3.6.1.4.1.498.6.8.4.1.ALM where ALM = 1 for sc5002NoResponse alarm, 2 for sc5002DiagRxErr alarm, etc., as specified in the Alarm Definitions above.
SCI sc5002NearEndAlarmCfgIndex	1.3.6.1.4.1.498.6.8.3.2.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC5002 to which this entry is applicable. SCinstance is defined to be ssllddcc where: ss (byte value) - physical shelf slot location (01-32) ll (byte value) - line number (01-128) dd (byte value) - drop number (00-31) cc (byte value) - channel or interface number (always 00)
sc5002NearEndAlarmCfgTable	1.3.6.1.4.1.498.6.8.3.2		not-accessible	This table contains entries that configure Near End Alarm reporting.
INT sc5002NearEndAlarmThreshold	1.3.6.1.4.1.498.6.8.3.2.1.4	INTEGER	read-write	The number of events which must be exceed, within the time period specified by the alarm's window, before declaring an alarm
INT sc5002NearEndAlarmWindow	1.3.6.1.4.1.498.6.8.3.2.1.3	INTEGER	read-write	The time period in which a specified number of events must occur, (specified by the alarm's threshold), before declaring an alarm condition. After reporting an Alarm condition and upon expiration of the window time period, the event count is reset to zero and another time period is begun. If the specified number of events is not exceeded within the next time period, an Alarm Cleared condition is reported.
sc5002NearEndBkdBlkErr	1.3.6.1.4.1.498.6.8.3.1.13
sc5002NearEndCurrent15MinEntry	1.3.6.1.4.1.498.6.8.6.1.1		not-accessible	An entry in the sc5002 NearEnd Current table.
SCI sc5002NearEndCurrent15MinIndex	1.3.6.1.4.1.498.6.8.6.1.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC5002 to which this entry is applicable. SCinstance is defined to be ssllddcc where: ss (byte value) - physical shelf slot location (01-32) ll (byte value) - line number (01-128) dd (byte value) - drop number (00-31) cc (byte value) - channel or interface number (always 00)
OCT sc5002NearEndCurrent15MinStat	1.3.6.1.4.1.498.6.8.6.1.1.2	OCTET STRING	read-only	Returns a bitwise snapshot of the current 15Min statistics. 1.7 f/u 1.6 f/u 1.5 f/u 1.4 f/u 1.3 f/u 1.2 2^9 ES . 1.0 2^7 2.7 f/u 2.6 2^6 . 2.0 2^0 3.7 f/u 3.6 f/u 3.5 f/u 3.4 f/u 3.3 f/u 3.2 2^9 SES . 3.0 2^7 4.7 f/u 4.6 2^6 SES . 4.0 2^0 5.7 f/u 5.6 f/u 5.5 f/u 5.4 f/u 5.3 f/u 5.2 Counter Overflow (>65535) BBE 5.1 2^15 5.0 2^14 6.7 f/u 6.6 2^13 BBE . 6.0 2^7 7.7 f/u 7.6 2^6 BBE . 7.0 2^0 -- 8.7 f/u 8.6 f/u 8.5 f/u 8.4 f/u 8.3 f/u 8.2 2^9 UAS . 8.0 2^7 9.7 f/u 9.6 2^6 UAS . 9.0 2^0 10.7 f/u 10.6 f/u 10.5 f/u 10.4 f/u 10.3 f/u 10.2 Counter Overflow (>65535) LCV 10.1 2^15 10.0 2^14 11.7 f/u 11.6 2^13 LCV . 11.0 2^7 12.7 f/u 12.6 2^6 LCV . 12.0 2^0
sc5002NearEndCurrent15MinTable	1.3.6.1.4.1.498.6.8.6.1		not-accessible	The sc5002 Current table.
sc5002NearEndCurrent24HrEntry	1.3.6.1.4.1.498.6.8.6.3.1		not-accessible	An entry in the E1 Total table.
SCI sc5002NearEndCurrent24HrIndex	1.3.6.1.4.1.498.6.8.6.3.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC5002 to which this entry is applicable. SCinstance is defined to be ssllddcc where: ss (byte value) - physical shelf slot location (01-32) ll (byte value) - line number (01-128) dd (byte value) - drop number (00-31) cc (byte value) - channel or interface number (always 00)
OCT sc5002NearEndCurrent24HrStat	1.3.6.1.4.1.498.6.8.6.3.1.2	OCTET STRING	read-only	Returns a bitwise map of the current 24 hour table 1.7 f/u 1.6 f/u 1.5 f/u 1.4 f/u 1.3 f/u 1.2 1: Counter Overflow (>65535) ES 1.1 2^15 1.0 2^14 2.7 f/u 2.6 2^13 ES . 2.0 2^7 3.7 f/u 3.6 2^6 ES . 3.0 2^0 4.7 f/u 4.6 f/u 4.5 f/u 4.4 f/u 4.3 f/u 4.2 1: Counter Overflow (>65535) SES 4.1 2^15 4.0 2^14 5.7 f/u 5.6 2^13 SES . 5.0 2^7 6.7 f/u 6.6 2^6 SES . 6.0 2^0 7.7 f/u 7.6 f/u 7.5 f/u 7.4 f/u 7.3 f/u 7.2 1: Counter Overflow (>65535) BBE 7.1 2^15 7.0 2^14 -- 8.7 f/u 8.6 2^13 BBE . 8.0 2^7 9.7 f/u 9.6 2^6 BBE . 9.0 2^0 10.7 f/u 10.6 f/u 10.5 f/u 10.4 f/u 10.3 f/u 10.2 1: Counter Overflow (>65535) UAS 10.1 2^15 10.0 2^14 11.7 f/u 11.6 2^13 UAS . 11.0 2^7 12.7 f/u 12.6 2^6 UAS . 12.0 2^0 13.7 f/u 13.6 f/u 13.5 f/u 13.4 f/u 13.3 f/u 13.2 1: Counter Overflow (>65535) LCV 13.1 2^15 13.0 2^14 14.7 f/u 14.6 2^13 LCV . 14.0 2^7 15.7 f/u 15.6 2^6 LCV . 15.0 2^0
sc5002NearEndCurrent24HrTable	1.3.6.1.4.1.498.6.8.6.3		not-accessible	The E1 Current24Hr table. 4 hour interval.
sc5002NearEndErrSec	1.3.6.1.4.1.498.6.8.3.1.12
sc5002NearEndIntervalEntry	1.3.6.1.4.1.498.6.8.6.2.1		not-accessible	An entry in the E1 Interval table.
SCI sc5002NearEndIntervalIndex	1.3.6.1.4.1.498.6.8.6.2.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC5002 to which this entry is applicable. SCinstance is defined to be ssllddcc where: ss (byte value) - physical shelf slot location (01-32) ll (byte value) - line number (01-128) dd (byte value) - drop number (00-31) cc (byte value) - channel or interface number (always 00)
INT sc5002NearEndIntervalNumber	1.3.6.1.4.1.498.6.8.6.2.1.2	INTEGER	read-only	The number of Errored Seconds encountered by an E1 interface in one of the previous 16, individual 15 minute, intervals.
OCT sc5002NearEndIntervalStat	1.3.6.1.4.1.498.6.8.6.2.1.3	OCTET STRING	read-only	Returns a bitwise map of the interface in one of the previous 16, individual 15 minute, intervals. 1.7 f/u 1.6 f/u 1.5 f/u 1.4 f/u 1.3 f/u 1.2 2^9 ES . 1.0 2^7 2.7 f/u 2.6 2^6 . 2.0 2^0 3.7 f/u 3.6 f/u 3.5 f/u 3.4 f/u 3.3 f/u 3.2 2^9 SES . 3.0 2^7 4.7 f/u 4.6 2^6 SES . 4.0 2^0 5.7 f/u 5.6 f/u 5.5 f/u 5.4 f/u 5.3 f/u 5.2 Counter Overflow (>65535) BBE 5.1 2^15 5.0 2^14 6.7 f/u 6.6 2^13 BBE . 6.0 2^7 7.7 f/u 7.6 2^6 BBE . 7.0 2^0 -- 8.7 f/u 8.6 f/u 8.5 f/u 8.4 f/u 8.3 f/u 8.2 2^9 UAS . 8.0 2^7 9.7 f/u 9.6 2^6 UAS . 9.0 2^0 10.7 f/u 10.6 f/u 10.5 f/u 10.4 f/u 10.3 f/u 10.2 Counter Overflow (>65535) LCV 10.1 2^15 10.0 2^14 11.7 f/u 11.6 2^13 LCV . 11.0 2^7 12.7 f/u 12.6 2^6 LCV . 12.0 2^0
sc5002NearEndIntervalTable	1.3.6.1.4.1.498.6.8.6.2		not-accessible	The sc5002 Interval table.
sc5002NearEndLnCodeViol	1.3.6.1.4.1.498.6.8.3.1.11
sc5002NearEndRecent24HrEntry	1.3.6.1.4.1.498.6.8.6.4.1		not-accessible	An entry in the E1 Total table.
SCI sc5002NearEndRecent24HrIndex	1.3.6.1.4.1.498.6.8.6.4.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC5002 to which this entry is applicable. SCinstance is defined to be ssllddcc where: ss (byte value) - physical shelf slot location (01-32) ll (byte value) - line number (01-128) dd (byte value) - drop number (00-31) cc (byte value) - channel or interface number (always 00)
OCT sc5002NearEndRecent24HrStat	1.3.6.1.4.1.498.6.8.6.4.1.2	OCTET STRING	read-only	Returns a bitwise map of the current 24 hour table 1.7 f/u 1.6 f/u 1.5 f/u 1.4 f/u 1.3 f/u 1.2 1: Counter Overflow (>65535) ES 1.1 2^15 1.0 2^14 2.7 f/u 2.6 2^13 ES . 2.0 2^7 3.7 f/u 3.6 2^6 ES . 3.0 2^0 4.7 f/u 4.6 f/u 4.5 f/u 4.4 f/u 4.3 f/u 4.2 1: Counter Overflow (>65535) SES 4.1 2^15 4.0 2^14 5.7 f/u 5.6 2^13 SES . 5.0 2^7 6.7 f/u 6.6 2^6 SES . 6.0 2^0 7.7 f/u 7.6 f/u 7.5 f/u 7.4 f/u 7.3 f/u 7.2 1: Counter Overflow (>65535) BBE 7.1 2^15 7.0 2^14 -- 8.7 f/u 8.6 2^13 BBE . 8.0 2^7 9.7 f/u 9.6 2^6 BBE . 9.0 2^0 10.7 f/u 10.6 f/u 10.5 f/u 10.4 f/u 10.3 f/u 10.2 1: Counter Overflow (>65535) UAS 10.1 2^15 10.0 2^14 11.7 f/u 11.6 2^13 UAS . 11.0 2^7 12.7 f/u 12.6 2^6 UAS . 12.0 2^0 13.7 f/u 13.6 f/u 13.5 f/u 13.4 f/u 13.3 f/u 13.2 1: Counter Overflow (>65535) LCV 13.1 2^15 13.0 2^14 14.7 f/u 14.6 2^13 LCV . 14.0 2^7 15.7 f/u 15.6 2^6 LCV . 15.0 2^0
sc5002NearEndRecent24HrTable	1.3.6.1.4.1.498.6.8.6.4		not-accessible	The E1 Recent24Hr table. 4 hour interval.
INT sc5002NearEndResetStats	1.3.6.1.4.1.498.6.8.5.1.1.4	INTEGER	read-write	Supports the action of soft resetting the sc5002NearEndValidIntervals object. When this object is set to reset(2), then the unit will reset the sc5002ValidIntervals object to zero. The value of norm(1) can not be set by management.
sc5002NearEndSevErrSec	1.3.6.1.4.1.498.6.8.3.1.14
INT sc5002NearEndStatLastInitialized	1.3.6.1.4.1.498.6.8.5.1.1.5	INTEGER	read-only	Number of seconds from midnight Dec 31, 1969 up until sc5002NearEndValidIntervals was last initialized to zero
sc5002NearEndUnavailableTimeRegEntry	1.3.6.1.4.1.498.6.8.6.9.1		not-accessible	An entry in the Unavailable Time Register table.
SCI sc5002NearEndUnavailableTimeRegIndex	1.3.6.1.4.1.498.6.8.6.9.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC5002 to which this entry is applicable. SCinstance is defined to be ssllddcc where: ss (byte value) - physical shelf slot location (01-32) ll (byte value) - line number (01-128) dd (byte value) - drop number (00-31) cc (byte value) - channel or interface number (always 00)
INT sc5002NearEndUnavailableTimeRegNumber	1.3.6.1.4.1.498.6.8.6.9.1.2	INTEGER	read-only	A number between 1 and 6, where the number is the number of the Unavailable Time Register.
INT sc5002NearEndUnavailableTimeRegStart	1.3.6.1.4.1.498.6.8.6.9.1.3	INTEGER	read-only	Start time of one of the Unavailable Time Registers.
INT sc5002NearEndUnavailableTimeRegStop	1.3.6.1.4.1.498.6.8.6.9.1.4	INTEGER	read-only	Stop time of one of the Unavailable Time Registers.
sc5002NearEndUnavailableTimeRegTable	1.3.6.1.4.1.498.6.8.6.9		not-accessible	The sc5002 Unavailable Time Register table.
sc5002NearEndUnavlSec	1.3.6.1.4.1.498.6.8.3.1.15
INT sc5002NearEndValidIntervals	1.3.6.1.4.1.498.6.8.5.1.1.9	INTEGER	read-only	The number of previous intervals for which valid data was collected. The value will be 16 unless the interface was brought on-line within the last 4 hours, in which case the value will be the number of complete 15 minute intervals the since interface has been online.
sc5002NetworkCfg	1.3.6.1.4.1.498.6.8.2
sc5002NetworkCfgEntry	1.3.6.1.4.1.498.6.8.2.1.1		not-accessible	The sc5002 Network Configuration Table Entry.
SCI sc5002NetworkCfgIndex	1.3.6.1.4.1.498.6.8.2.1.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC5002 to which this entry is applicable. SCinstance is defined to be ssllddcc where: ss (byte value) - physical shelf slot location (01-32) ll (byte value) - line number (01-128) dd (byte value) - drop number (00-31) cc (byte value) - channel or interface number (always 00)
sc5002NetworkCfgTable	1.3.6.1.4.1.498.6.8.2.1		not-accessible	This table contains objects that support the specific management requirements for configuring the SC5002 Network Interface level objects.
sc5002NoResponse	1.3.6.1.4.1.498.6.8.3.1.1
sc5002NvRamCorrupt	1.3.6.1.4.1.498.6.8.3.1.4
sc5002Performance	1.3.6.1.4.1.498.6.8.6
sc5002PowerUp	1.3.6.1.4.1.498.6.8.3.1.3
sc5002RecentFarEnd24HrEntry	1.3.6.1.4.1.498.6.8.6.8.1		not-accessible	An entry in the Recent 24 Hr table.
SCI sc5002RecentFarEnd24HrIndex	1.3.6.1.4.1.498.6.8.6.8.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC5002 to which this entry is applicable. SCinstance is defined to be ssllddcc where: ss (byte value) - physical shelf slot location (01-32) ll (byte value) - line number (01-128) dd (byte value) - drop number (00-31) cc (byte value) - channel or interface number (always 00)
OCT sc5002RecentFarEnd24HrStat	1.3.6.1.4.1.498.6.8.6.8.1.2	OCTET STRING	read-only	Returns a bitwise map of statistics for the interface in the Recent 24 hour interval. 1.7 f/u 1.6 f/u 1.5 f/u 1.4 f/u 1.3 f/u 1.2 1: Counter Overflow (>65535) ES 1.1 2^15 1.0 2^14 2.7 f/u 2.6 2^13 ES . 2.0 2^7 3.7 f/u 3.6 2^6 ES . 3.0 2^0 4.7 f/u 4.6 f/u 4.5 f/u 4.4 f/u 4.3 f/u 4.2 1: Counter Overflow (>65535) SES 4.1 2^15 4.0 2^14 5.7 f/u 5.6 2^13 SES . 5.0 2^7 6.7 f/u 6.6 2^6 SES . 6.0 2^0 7.7 f/u 7.6 f/u 7.5 f/u 7.4 f/u 7.3 f/u 7.2 1: Counter Overflow (>65535) BBE 7.1 2^15 7.0 2^14 8.7 f/u 8.6 2^13 BBE . 8.0 2^7 9.7 f/u 9.6 2^6 BBE . 9.0 2^0 10.7 f/u 10.6 f/u 10.5 f/u 10.4 f/u 10.3 f/u 10.2 1: Counter Overflow (>65535) UAS 10.1 2^15 10.0 2^14 11.7 f/u 11.6 2^13 UAS . 11.0 2^7 12.7 f/u 12.6 2^6 UAS . 12.0 2^0
sc5002RecentFarEnd24HrTable	1.3.6.1.4.1.498.6.8.6.8		not-accessible	The Recent 24 Hour table.
INT sc5002SoftReset	1.3.6.1.4.1.498.6.8.5.1.1.2	INTEGER	read-write	Supports the action of soft resetting the unit. When this object is set to reset(1), then the unit performs a soft reset, whose meaning is specific to the type of unit being managed. The value of norm(2) will be returned when the reset is complete. The value of norm(2) can not be set by management.
STR sc5002StoredFirmwareRev	1.3.6.1.4.1.498.6.8.1.2.1.3	DisplayString	read-only	The version number of the firmware stored (in a compressed format) but not currently executing. MM: Major Revision (0-99) NN: Minor Revision (0-99) BB: Bug Fix Revision (0-99)
INT sc5002StoredFirmwareStatus	1.3.6.1.4.1.498.6.8.1.2.1.5	INTEGER	read-only	This object represents the state of the Non-Active or Stored firmware: statBlank(1) Factory Default statDownLoading(2) In process of downloading firmware statOK(3) Zipped version checksum succesful (OK to switch) (can set sc5002SwitchActive to switchActive(2)) statCheckSumBad(4) Failed checksum after download statUnZipping(5) In process of uncompressing into active area statBadUnZip(6) Failed last uncompress The object is read only.
INT sc5002SwitchActiveFirmware	1.3.6.1.4.1.498.6.8.1.2.1.6	INTEGER	read-write	This object is used to switch the active executing firmware from the version in sc5002ActiveRev to the version in sc5002StoredRev. When a switchActive(2) is set (write only) the element will: 1) reboot 2) uncompress stored code into active area 3) perform checksum on active area 4) Set sc5002StoredStatus object to indicate results 5) If succesfull: update sc5002ActiveFirmwareRev and sc5002StoredFirmwareRev and begin executing If failed: replace active area with previous revision The switchNorm(1) enumeration will always be read. Setting switchActive(2) when the sc5002StoredStatus is not statOK(3) will result in an error.
INT sc5002SysUpTime	1.3.6.1.4.1.498.6.8.5.1.1.11	INTEGER	read-only	This variable is used to report the elapsed system tick time for conversion to real time at the controller and is not related to the sysUpTime referenced in MIB-II. Upon power-up of the unit, the elapsed time is cleared. The elapsed time counter rolls over upon reaching the maximum count.
INT sc5002TestResult	1.3.6.1.4.1.498.6.8.4.1.1.3	INTEGER	read-only	The results of the last diagnostic test completed. The value returned is only valid if a get of sc5002LoopbackConfig returns noLoopBack(1).
sc5002TimingLoss	1.3.6.1.4.1.498.6.8.3.1.6
sc5002UnitFailure	1.3.6.1.4.1.498.6.8.3.1.5
sc5002Version	1.3.6.1.4.1.498.6.8.1
sc5002VersionEntry	1.3.6.1.4.1.498.6.8.1.2.1		not-accessible	An entry in the GDC SC5002 Version Table.
SCI sc5002VersionIndex	1.3.6.1.4.1.498.6.8.1.2.1.1	SCinstance	read-only	Identifies Version parameters associated with the managed object.
sc5002VersionTable	1.3.6.1.4.1.498.6.8.1.2		not-accessible

RFC description

Manages configuration and performance monitoring for General DataComm SC5002 T1/E1 network devices.

Start monitoring General DataComm SC5002-series equipment (firmware revision/E1 alarm configuration) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SC5002-MIB

What Is SC5002-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description