All MIBs › SAMSUNG-PRINTER-EXT-MIB
Organization: Samsung Common Management Interface Working Group
Last Updated: 1904-07-17
Category: Printer Management, Samsung Device Management
Description: Manages Samsung printer-specific extensions including consumables, trays, and job accounting.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is SAMSUNG-PRINTER-EXT-MIB?
SAMSUNG-PRINTER-EXT-MIB is a vendor extension module from Samsung that supplements the IETF Printer MIB (RFC 1759) with Samsung-specific SCMI (Samsung Common Management Interface) objects for their laser printers and multifunction devices. It exposes data layered on top of the standard printer status model, such as consumable levels, paper tray status, and job accounting detail specific to Samsung firmware. It is used to monitor the hardware and consumables status of a Samsung printer -- toner/drum remaining life, tray/output bin state, and print job completion/error status -- extending the base standard's device-status objects rather than duplicating them. It explicitly depends on and extends the IETF Printer MIB, so it is deployed alongside that standard module rather than standalone. It is typically used by print-fleet management software polling networked Samsung printers and MFPs for supply levels and job status, and administrators can load the module into a SAMSUNG-PRINTER-EXT-MIB MIB Browser session for ad hoc inspection.
IPNetwork Monitor allows you to monitor SNMP objects defined in SAMSUNG-PRINTER-EXT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Samsung network printers
- Samsung multifunction printers (MFPs)
Monitoring Examples
No object or table names were provided in the sample for this module, so specific identifiers can't be cited; based on the module description, this MIB would typically be polled alongside the standard Printer MIB's marker-supplies and detected-error-state objects to add Samsung-specific detail such as per-tray media status and drum/toner remaining percentage not covered by the base standard.
What Can Be Monitored
- toner/drum consumable levels
- paper tray status
- print job accounting
- printer error conditions
This MIB depends on
Related MIBs
Imported Objects
From HOST-RESOURCES-MIB
| hrDeviceIndex | OBJECT-TYPE |
From Printer-MIB
| PresentOnOff | |
| prtChannelEntry | OBJECT-TYPE |
| prtGeneralEntry | OBJECT-TYPE |
| prtInputEntry | OBJECT-TYPE |
| prtInterpreterEntry | OBJECT-TYPE |
| prtInterpreterIndex | OBJECT-TYPE |
| prtOutputEntry | OBJECT-TYPE |
From SAMSUNG-COMMON-MIB
| samsungCommonMIB | OBJECT-IDENTITY |
From SAMSUNG-GENERAL-TC
| Cardinal32 | |
| Ordinal32 |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE |
From SNMPv2-TC
| DisplayString | |
| RowStatus |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| scmPrintMIB | 1.3.6.1.4.1.236.11.5.11.55 | Version: 1.00 Samsung SCMI Extension to IETF Printer MIB Module. This Module provides extension to the IETF Printer MIB. Copyright (C) 2003-2004 Samsung Corporation. All Rights Reserved. | ||
| scmPrtAlert | 1.3.6.1.4.1.236.11.5.11.55.26 | |||
| INT scmPrtAlertAlarmShortage | 1.3.6.1.4.1.236.11.5.11.55.26.1.1 | INTEGER | read-write | Printer Alert Alarm Shortage |
| I32 scmPrtAlertAlarmShortageOptions | 1.3.6.1.4.1.236.11.5.11.55.26.1.2 | Integer32 | read-only | Printer Alert Shortage Oprions |
| scmPrtAlertGroup | 1.3.6.1.4.1.236.11.5.11.55.2.3.26 | Description. | ||
| scmPrtAlertSimple | 1.3.6.1.4.1.236.11.5.11.55.26.1 | |||
| scmPrtBase | 1.3.6.1.4.1.236.11.5.11.55.1 | |||
| scmPrtBaseEntry | 1.3.6.1.4.1.236.11.5.11.55.1.2.1 | not-accessible | An entry of general counters and information for ease of use of the SCMI Extension to IETF Printer MIB Module and the IETF Printer MIB on this host system. Usage: The ONLY valid row in the 'scmPrtBaseTable' shall ALWAYS have an 'scmPrtBaseIndex' of one ('1'). | |
| scmPrtBaseGroup | 1.3.6.1.4.1.236.11.5.11.55.2.3.1 | The general printer group extension. | ||
| ORD scmPrtBaseIndex | 1.3.6.1.4.1.236.11.5.11.55.1.2.1.1 | Ordinal32 | not-accessible | A unique value used by this host system to identify this conceptual row in the 'scmPrtBaseTable'. Usage: The ONLY valid row in the 'scmPrtBaseTable' shall ALWAYS have an 'scmPrtBaseIndex' of one ('1'). |
| ROW scmPrtBaseRowStatus | 1.3.6.1.4.1.236.11.5.11.55.1.2.1.2 | RowStatus | read-only | This object is used to display status of the ONLY valid conceptual row in the 'scmPrtBaseTable'. Usage: 'scmPrtBaseRowStatus' is 'read-only' because the ONLY valid conceptual row shall NOT be deleted. |
| scmPrtBaseTable | 1.3.6.1.4.1.236.11.5.11.55.1.2 | not-accessible | A table of general counters and information for ease of use of the SCMI Extension to IETF Printer MIB Module and the IETF Printer MIB on this host system. Usage: The ONLY valid row in the 'scmPrtBaseTable' shall ALWAYS have an 'scmPrtBaseIndex' of one ('1'). | |
| scmPrtChannel | 1.3.6.1.4.1.236.11.5.11.55.14 | |||
| scmPrtChannelEntry | 1.3.6.1.4.1.236.11.5.11.55.14.2.1 | not-accessible | An entry exists corresponding to each entry in the prtChannelTable. | |
| CAR scmPrtChannelEOJTimeout | 1.3.6.1.4.1.236.11.5.11.55.14.2.1.2 | Cardinal32 | read-create | Defines the number of seconds that the channel waits before timing out. For example, this may be used for the parallel channel. The value zero means infinite or no timeout on the channel. |
| scmPrtChannelGroup | 1.3.6.1.4.1.236.11.5.11.55.2.3.14 | The Channel group extension. | ||
| ROW scmPrtChannelRowStatus | 1.3.6.1.4.1.236.11.5.11.55.14.2.1.1 | RowStatus | read-create | Manages the status of this conceptual row in the scmPrtChannelTable. |
| scmPrtChannelSimple | 1.3.6.1.4.1.236.11.5.11.55.14.1 | |||
| scmPrtChannelTable | 1.3.6.1.4.1.236.11.5.11.55.14.2 | not-accessible | This table logically augments Printer MIB's prtChannelTable. | |
| scmPrtConfiguratioinGroup | 1.3.6.1.4.1.236.11.5.11.55.2.3.19 | Description. | ||
| scmPrtConfiguration | 1.3.6.1.4.1.236.11.5.11.55.19 | |||
| I32 scmPrtConfigurationAltitudeAction | 1.3.6.1.4.1.236.11.5.11.55.19.1.7 | Integer32 | read-write | The value 'low(1)' will be used when the printer is in the low altitude location. The value 'high(2)' will be used when the printer is in the high altitude location. |
| INT scmPrtConfigurationAltitudeActionOptions | 1.3.6.1.4.1.236.11.5.11.55.19.1.8 | INTEGER | read-only | The value of this object will be the bitwise OR of the supported values for altitudeAction in this printer. |
| I32 scmPrtConfigurationAutocont | 1.3.6.1.4.1.236.11.5.11.55.19.1.3 | Integer32 | read-write | It determines the printer action when the user prints a page without paper in the manual feed slot but the paper source is set to manual feed. If Auto Continue is ON the printer pick up the paper from the tray after few second. If it is OFF the printer wait forever until user insert paper into a manual feed slot. |
| INT scmPrtConfigurationAutoCountOptions | 1.3.6.1.4.1.236.11.5.11.55.19.1.4 | INTEGER | read-only | available options of the model |
| scmPrtConfigurationEntry | 1.3.6.1.4.1.236.11.5.11.55.19.2.1 | not-accessible | ||
| ORD scmPrtConfigurationIndex | 1.3.6.1.4.1.236.11.5.11.55.19.2.1.1 | Ordinal32 | read-only | |
| INT scmPrtConfigurationJam2RecOptions | 1.3.6.1.4.1.236.11.5.11.55.19.1.6 | INTEGER | read-only | available options of the model |
| I32 scmPrtConfigurationJam2Recover | 1.3.6.1.4.1.236.11.5.11.55.19.1.5 | Integer32 | read-write | if it is on and occur JAM at Jam2 point printer will print this page again. |
| I32 scmPrtConfigurationPowerSave | 1.3.6.1.4.1.236.11.5.11.55.19.1.1 | Integer32 | read-write | set power save mode 1: power save mode |
| INT scmPrtConfigurationPowerSaveOptions | 1.3.6.1.4.1.236.11.5.11.55.19.1.2 | INTEGER | read-only | available options of the model |
| scmPrtConfigurationSimple | 1.3.6.1.4.1.236.11.5.11.55.19.1 | |||
| scmPrtConfigurationTable | 1.3.6.1.4.1.236.11.5.11.55.19.2 | not-accessible | ||
| scmPrtConsoleDisplayBuffer | 1.3.6.1.4.1.236.11.5.11.55.27 | |||
| scmPrtConsoleDisplayBufferGroup | 1.3.6.1.4.1.236.11.5.11.55.2.3.27 | Description. | ||
| INT scmPrtConsoleDisplayBufferLcdLangType | 1.3.6.1.4.1.236.11.5.11.55.27.1.1 | INTEGER | read-write | Printer Console (LCD) Display String Language Type |
| I32 scmPrtConsoleDisplayBufferLcdLangTypeOptions | 1.3.6.1.4.1.236.11.5.11.55.27.1.2 | Integer32 | read-write | Printer Console (LCD) Display String Language Type Option |
| scmPrtConsoleDisplayBufferSimple | 1.3.6.1.4.1.236.11.5.11.55.27.1 | |||
| scmPrtCount | 1.3.6.1.4.1.236.11.5.11.55.20 | |||
| INT scmPrtCountColorant | 1.3.6.1.4.1.236.11.5.11.55.20.2.1.5 | INTEGER | read-only | Description. |
| INT scmPrtCountDeviceType | 1.3.6.1.4.1.236.11.5.11.55.20.2.1.2 | INTEGER | read-only | Description. |
| I32 scmPrtCountDrumImageCount | 1.3.6.1.4.1.236.11.5.11.55.20.1.1 | Integer32 | read-only | |
| INT scmPrtCountDrumImageCountReset | 1.3.6.1.4.1.236.11.5.11.55.20.1.2 | INTEGER | read-write | |
| INT scmPrtCountDuplex | 1.3.6.1.4.1.236.11.5.11.55.20.2.1.6 | INTEGER | read-only | Description. |
| scmPrtCountEntry | 1.3.6.1.4.1.236.11.5.11.55.20.2.1 | not-accessible | ||
| I32 scmPrtCountFuserImageCount | 1.3.6.1.4.1.236.11.5.11.55.20.1.5 | Integer32 | read-only | |
| INT scmPrtCountFuserImageCountReset | 1.3.6.1.4.1.236.11.5.11.55.20.1.6 | INTEGER | read-write | |
| scmPrtCountGroup | 1.3.6.1.4.1.236.11.5.11.55.2.3.20 | Description. | ||
| I32 scmPrtCountIndex | 1.3.6.1.4.1.236.11.5.11.55.20.2.1.1 | Integer32 | read-only | |
| INT scmPrtCountMediaSize | 1.3.6.1.4.1.236.11.5.11.55.20.2.1.4 | INTEGER | read-only | Paper size options that are available in this model. Some printer such like ML6060 or Modena have a 4 bytes data length. So, to distinguish these models we have to check model id or version. |
| I32 scmPrtCountPickupMPCount | 1.3.6.1.4.1.236.11.5.11.55.20.1.9 | Integer32 | read-only | |
| INT scmPrtCountPickupMPReset | 1.3.6.1.4.1.236.11.5.11.55.20.1.10 | INTEGER | read-write | |
| I32 scmPrtCountPickupTray1Count | 1.3.6.1.4.1.236.11.5.11.55.20.1.11 | Integer32 | read-only | |
| INT scmPrtCountPickupTray1Reset | 1.3.6.1.4.1.236.11.5.11.55.20.1.12 | INTEGER | read-write | |
| I32 scmPrtCountPickupTray2Count | 1.3.6.1.4.1.236.11.5.11.55.20.1.13 | Integer32 | read-only | |
| INT scmPrtCountPickupTray2Reset | 1.3.6.1.4.1.236.11.5.11.55.20.1.14 | INTEGER | read-write | |
| INT scmPrtCountResolution | 1.3.6.1.4.1.236.11.5.11.55.20.2.1.7 | INTEGER | read-write | Description. |
| scmPrtCountSimple | 1.3.6.1.4.1.236.11.5.11.55.20.1 | |||
| scmPrtCountTable | 1.3.6.1.4.1.236.11.5.11.55.20.2 | not-accessible | ||
| I32 scmPrtCountTransferImageCount | 1.3.6.1.4.1.236.11.5.11.55.20.1.3 | Integer32 | read-only | |
| INT scmPrtCountTransferImageCountReset | 1.3.6.1.4.1.236.11.5.11.55.20.1.4 | INTEGER | read-write | |
| I32 scmPrtCountTwoRollerCount | 1.3.6.1.4.1.236.11.5.11.55.20.1.7 | Integer32 | read-only | |
| INT scmPrtCountTwoRollerReset | 1.3.6.1.4.1.236.11.5.11.55.20.1.8 | INTEGER | read-write | |
| INT scmPrtCountType | 1.3.6.1.4.1.236.11.5.11.55.20.2.1.3 | INTEGER | read-only | Description. |
| INT scmPrtCountUnit | 1.3.6.1.4.1.236.11.5.11.55.20.2.1.8 | INTEGER | read-only | Description. |
| I32 scmPrtCountValue | 1.3.6.1.4.1.236.11.5.11.55.20.2.1.9 | Integer32 | read-only | Description. |
| scmPrtGeneral | 1.3.6.1.4.1.236.11.5.11.55.5 | |||
| scmPrtGeneralEntry | 1.3.6.1.4.1.236.11.5.11.55.5.2.1 | not-accessible | An entry exists in this table for each device entry in the hostmib device table whose type is printer. | |
| scmPrtGeneralGroup | 1.3.6.1.4.1.236.11.5.11.55.2.3.5 | The general printer group extension. | ||
| INT scmPrtGeneralPrncolorPPM | 1.3.6.1.4.1.236.11.5.11.55.5.1.23 | INTEGER | read-only | Color Printing PPM |
| STR scmPrtGeneralPrnEngFWVer | 1.3.6.1.4.1.236.11.5.11.55.5.1.12 | DisplayString | read-only | Print Engine FW Version |
| STR scmPrtGeneralPrnEpsonVer | 1.3.6.1.4.1.236.11.5.11.55.5.1.14 | DisplayString | read-only | Print Epson Version |
| STR scmPrtGeneralPrnKS5843Ver | 1.3.6.1.4.1.236.11.5.11.55.5.1.18 | DisplayString | read-only | Printer KS5843 Version. |
| STR scmPrtGeneralPrnKS5895Ver | 1.3.6.1.4.1.236.11.5.11.55.5.1.20 | DisplayString | read-only | Printer KS5895 Version. |
| STR scmPrtGeneralPrnKSSMVer | 1.3.6.1.4.1.236.11.5.11.55.5.1.19 | DisplayString | read-only | Printer KSSM Version. |
| STR scmPrtGeneralPrnMainSystemVer | 1.3.6.1.4.1.236.11.5.11.55.5.1.21 | DisplayString | read-only | Printer Main System Versio. |
| OCT scmPrtGeneralPrnManufacture | 1.3.6.1.4.1.236.11.5.11.55.5.1.6 | OCTET STRING | read-only | Printer DRAM Size. |
| OCT scmPrtGeneralPrnModelDescr | 1.3.6.1.4.1.236.11.5.11.55.5.1.5 | OCTET STRING | read-only | Printer HDD Size. |
| STR scmPrtGeneralPrnModelName | 1.3.6.1.4.1.236.11.5.11.55.5.1.1 | DisplayString | read-only | Represent the printer model name currently being connected with NPC. |
| OCT scmPrtGeneralPrnModelVer | 1.3.6.1.4.1.236.11.5.11.55.5.1.3 | OCTET STRING | read-only | Model version number. |
| STR scmPrtGeneralPrnOSFWVer | 1.3.6.1.4.1.236.11.5.11.55.5.1.2 | DisplayString | read-only | Printer Software version number. |
| STR scmPrtGeneralPrnPCL5CeVer | 1.3.6.1.4.1.236.11.5.11.55.5.1.24 | DisplayString | read-only | Print PCL5Ce Version |
| STR scmPrtGeneralPrnPCL5eVer | 1.3.6.1.4.1.236.11.5.11.55.5.1.15 | DisplayString | read-only | Print PCL5e Version |
| STR scmPrtGeneralPrnPCLFWVer | 1.3.6.1.4.1.236.11.5.11.55.5.1.11 | DisplayString | read-only | PCL Version information of printer |
| STR scmPrtGeneralPrnPSFWVer | 1.3.6.1.4.1.236.11.5.11.55.5.1.16 | DisplayString | read-only | PS Version information of printer |
| STR scmPrtGeneralPrnScanFWVer | 1.3.6.1.4.1.236.11.5.11.55.5.1.17 | DisplayString | read-only | Scanner FW Version |
| STR scmPrtGeneralPrnSCFFWVer | 1.3.6.1.4.1.236.11.5.11.55.5.1.13 | DisplayString | read-only | Print SCF FW Version |
| STR scmPrtGeneralPrnSerialNo | 1.3.6.1.4.1.236.11.5.11.55.5.1.4 | DisplayString | read-only | Printer Serial number. |
| STR scmPrtGeneralPrnSPLVer | 1.3.6.1.4.1.236.11.5.11.55.5.1.22 | DisplayString | read-only | Print SPL Version |
| OCT scmPrtGeneralPrnVendor | 1.3.6.1.4.1.236.11.5.11.55.5.1.7 | OCTET STRING | read-only | Print Per Minute |
| ROW scmPrtGeneralRowStatus | 1.3.6.1.4.1.236.11.5.11.55.5.2.1.1 | RowStatus | read-create | Manages the status of this conceptual row in the scmPrtGeneralTable. |
| scmPrtGeneralSimple | 1.3.6.1.4.1.236.11.5.11.55.5.1 | |||
| scmPrtGeneralTable | 1.3.6.1.4.1.236.11.5.11.55.5.2 | not-accessible | A table of general information per printer. This table augments the prtGeneralTable. | |
| scmPrtInput | 1.3.6.1.4.1.236.11.5.11.55.8 | |||
| I32 scmPrtInputCustDimFeedDirDecl | 1.3.6.1.4.1.236.11.5.11.55.8.2.1.4 | Integer32 | read-create | Provides the dimension, in the feed direction, of the media in this input subunit, when the value of scmPrtInputUseCustomSize is set to 'On'. When scmPrtInputUseCustomSize is set to On, this value is copied to prtInputMediaDimFeedDirDeclared and prtInputMediaDimFeedDirChosen. |
| I32 scmPrtInputCustDimXFeedDirDecl | 1.3.6.1.4.1.236.11.5.11.55.8.2.1.5 | Integer32 | read-create | Provides the dimension, in the feed direction, of the media in this input subunit, when the value of scmPrtInputUseCustomSize is set to 'On'. When scmPrtInputUseCustomSize is set to 'On', this value is copied to prtInputMediaDimFeedDirDeclared and prtInputMediaDimFeedDirChosen. |
| scmPrtInputEntry | 1.3.6.1.4.1.236.11.5.11.55.8.2.1 | not-accessible | Entries may exist for each entry in the prtInputTable. | |
| scmPrtInputGroup | 1.3.6.1.4.1.236.11.5.11.55.2.3.8 | The input group extension. | ||
| I32 scmPrtInputLockTray | 1.3.6.1.4.1.236.11.5.11.55.8.1.3 | Integer32 | read-write | Trays and combination trays can be locked out of the paper selection process. The available options depend on the configuration of MP tray. |
| I32 scmPrtInputLockTrayOptions | 1.3.6.1.4.1.236.11.5.11.55.8.1.4 | Integer32 | read-write | available options of the model |
| I32 scmPrtInputNextPrtInputIndex | 1.3.6.1.4.1.236.11.5.11.55.8.2.1.2 | Integer32 | read-create | The value of prtInputIndex corresponding to the input subunit which will be used when this input subunit is emptied. The value of zero indicates that auto input switching will not occur when this input subunit is emptied. Two different mechanisms for input tray switching, scmPrtNextPrtInputIndex and scmPrtInputAliasGroup, are provided. A device agent may make use of one or the other, none, or both. Use the model that fits best for the given application. Usage: Conforming management agents, which ALSO implement the the Printer MIB v2, SHALL set 'scmPrtInputNextPrtInputIndex' to the SAME value as 'prtInputNextIndex' (i.e., the values of these two objects SHALL be interlocked). |
| I32 scmPrtInputPaperSize | 1.3.6.1.4.1.236.11.5.11.55.8.2.1.7 | Integer32 | read-create | Value of Paper size for printing. Some printer such like ML6060 or Modena have a 4 bytes data length. So, to distinguish these models we have to check model id or version. |
| INT scmPrtInputPaperSizeOptions | 1.3.6.1.4.1.236.11.5.11.55.8.2.1.8 | INTEGER | read-only | Paper size options that are available in this model. Some printer such like ML6060 or Modena have a 4 bytes data length. So, to distinguish these models we have to check model id or version. |
| I32 scmPrtInputPaperType | 1.3.6.1.4.1.236.11.5.11.55.8.1.5 | Integer32 | read-write | It determines paper thickness. |
| INT scmPrtInputPaperTypeOptions | 1.3.6.1.4.1.236.11.5.11.55.8.1.6 | INTEGER | read-write | available options of current model |
| ROW scmPrtInputRowStatus | 1.3.6.1.4.1.236.11.5.11.55.8.2.1.1 | RowStatus | read-create | Manages the status of this conceptual row in the scmPrtInputTable. |
| scmPrtInputSimple | 1.3.6.1.4.1.236.11.5.11.55.8.1 | |||
| scmPrtInputTable | 1.3.6.1.4.1.236.11.5.11.55.8.2 | not-accessible | This table logically augments the Printer MIB's prtInputTable. | |
| I32 scmPrtInputTrayNum | 1.3.6.1.4.1.236.11.5.11.55.8.2.1.9 | Integer32 | read-create | It can select the type of paper tray. The types of tray can be varied according to the printer model |
| I32 scmPrtInputTrayNumOptions | 1.3.6.1.4.1.236.11.5.11.55.8.2.1.10 | Integer32 | read-create | available options of tray types |
| I32 scmPrtInputTrayPriority | 1.3.6.1.4.1.236.11.5.11.55.8.2.1.6 | Integer32 | read-create | The current priority of this tray. This value/mechanism is independent of scmPrtNextPrtInputIndex and scmPrtInputAliasGroup. Usage: The priority of this device, where '0' is unspecified (default), '1' is lowest, and '100' is highest. |
| I32 scmPrtInputTraySwitch | 1.3.6.1.4.1.236.11.5.11.55.8.1.1 | Integer32 | read-write | if language is set to AUTO, this options can the printer anlyzes the stream of data being sent to determine which language is being used by the printer job, and the printer's emulation language automatically be switched if this options is set. |
| INT scmPrtInputTraySwitchOptions | 1.3.6.1.4.1.236.11.5.11.55.8.1.2 | INTEGER | read-write | available options of the model |
| PRE scmPrtInputUseCustomSize | 1.3.6.1.4.1.236.11.5.11.55.8.2.1.3 | PresentOnOff | read-create | Specifies how this input subunit determines the paper size to use. If the value is 'Off' this input subunit uses the paper size automatically sensed by the subunit. If the value is 'On' this input subunit uses the custom dimensions provided by scmPrtInputCustDimFeedDirDecl and scmPrtInputCustDimXFeedDirDecl. |
| ORD scmPrtInterpJobCopiesDefault | 1.3.6.1.4.1.236.11.5.11.55.15.2.1.9 | Ordinal32 | read-create | This defines the default number of job copies to be printed by this interpreter. If set incorrectly, this object may cause difficulties at customer sites. Agent developers should consider making this object read-only, permanently set to one copy. |
| PRE scmPrtInterpLineTerm | 1.3.6.1.4.1.236.11.5.11.55.15.2.1.33 | PresentOnOff | read-create | Enables adding a Carriage Return after every Line Feed. The value 'On' indicates that a Carriage Return will be added after every Line Feed. Usage example: This is a useful feature when printing text jobs via PCL through a standard queue in UNIX. The value 'other' shall mean not specified. |
| I32 scmPrtInterpOrientation | 1.3.6.1.4.1.236.11.5.11.55.15.2.1.60 | Integer32 | read-create | It determines the direction of the print image on the page. The first two kinds of options are portrait(tall) and landscape(wide). reversePortrait is 180 degrees rotation of portrait. reverseLandscape is 180 degrees rotation of landscape. |
| INT scmPrtInterpOrientationOptions | 1.3.6.1.4.1.236.11.5.11.55.15.2.1.61 | INTEGER | read-only | available options in orientation |
| PRE scmPrtInterpProcessBarcodes | 1.3.6.1.4.1.236.11.5.11.55.15.2.1.54 | PresentOnOff | read-create | Specifies whether the 'extra' barcode processing within the interpreter should be used. |
| scmPrtInterpreter | 1.3.6.1.4.1.236.11.5.11.55.15 | |||
| INT scmPrtInterpreterCopyNum | 1.3.6.1.4.1.236.11.5.11.55.15.1.1 | INTEGER | read-write | It can select how many papers are printed Normally it can be selected 1- 999. |
| I32 scmPrtInterpreterEmulation | 1.3.6.1.4.1.236.11.5.11.55.15.1.2 | Integer32 | read-write | Emulation option |
| INT scmPrtInterpreterEmulationOptions | 1.3.6.1.4.1.236.11.5.11.55.15.1.3 | INTEGER | read-write | available options of the model |
| scmPrtInterpreterEntry | 1.3.6.1.4.1.236.11.5.11.55.15.2.1 | not-accessible | An entry exists corresponding to each entry in the prtInterpreterTable. | |
| scmPrtInterpreterGroup | 1.3.6.1.4.1.236.11.5.11.55.2.3.15 | The interpreter group extension. | ||
| scmPrtInterpreterSimple | 1.3.6.1.4.1.236.11.5.11.55.15.1 | |||
| scmPrtInterpreterTable | 1.3.6.1.4.1.236.11.5.11.55.15.2 | not-accessible | This table logically augments the Printer MIB's prtInterpreterTable. | |
| ROW scmPrtInterpRowStatus | 1.3.6.1.4.1.236.11.5.11.55.15.2.1.1 | RowStatus | read-create | Manages the status of this conceptual row in the scmPrtInterpreterTable. |
| scmPrtIPP | 1.3.6.1.4.1.236.11.5.11.55.25 | |||
| I32 scmPrtIPPCollatedCopies | 1.3.6.1.4.1.236.11.5.11.55.25.1.11 | Integer32 | read-write | The value of this object gives the number of collated copies printed for the each job. |
| I32 scmPrtIPPCollatedCopiesLBound | 1.3.6.1.4.1.236.11.5.11.55.25.1.9 | Integer32 | read-only | The value of this object gives the lower bound of the number of collated copies supported in this printer. |
| I32 scmPrtIPPCollatedCopiesUBound | 1.3.6.1.4.1.236.11.5.11.55.25.1.10 | Integer32 | read-only | The value of this object gives the upper bound of the number of collated copies supported in this printer. |
| INT scmPrtIPPColorSupported | 1.3.6.1.4.1.236.11.5.11.55.25.1.1 | INTEGER | read-only | The value of this object indicates whether the printer supports color printing. |
| I32 scmPrtIPPFinishings | 1.3.6.1.4.1.236.11.5.11.55.25.1.13 | Integer32 | read-write | The value of this object gives the set of finishings applied for each job. If bit 0 is set, no finishings are applied. If bit 1 is set, stapling is done for each job. If bit 2 is set, punching is done for each job. If bit 3 is set, the printed document will be covered. If bit 4 is set, binding will be done for each job. |
| I32 scmPrtIPPFinishingsSupported | 1.3.6.1.4.1.236.11.5.11.55.25.1.12 | Integer32 | read-only | The value of this object gives the type of finishings supported in the printer. If bit 1 is set, stapling is supported. If bit 2 is set, punching is supported. If bit 3 is set, covering of printed document is supported. If bit 4 is set, binding is supported. If bit 0 is set, the option of no finishings is supported. |
| scmPrtIPPGroup | 1.3.6.1.4.1.236.11.5.11.55.2.3.25 | Description. | ||
| I32 scmPrtIPPJobImpressionsCompleted | 1.3.6.1.4.1.236.11.5.11.55.25.1.20 | Integer32 | read-only | The value of this object gives the number of print images printed for the current job. |
| I32 scmPrtIPPJobImpressionsSupportedLBound | 1.3.6.1.4.1.236.11.5.11.55.25.1.4 | Integer32 | read-only | The value of this object gives the lower bound of the number of print images for a job. |
| I32 scmPrtIPPJobImpressionsSupportedUBound | 1.3.6.1.4.1.236.11.5.11.55.25.1.5 | Integer32 | read-only | The value of this object gives the upper bound of the number of print images for a job. |
| I32 scmPrtIPPJobKOctetsProcessed | 1.3.6.1.4.1.236.11.5.11.55.25.1.19 | Integer32 | read-only | The value of this object gives the number of units of 1024 octets printed for the current job. |
| I32 scmPrtIPPJobKOctetsSupportedLBound | 1.3.6.1.4.1.236.11.5.11.55.25.1.2 | Integer32 | read-only | The value of this object gives the lower bound of the size in units of 1024 octets for jobs accepted by the printer. |
| I32 scmPrtIPPJobKOctetsSupportedUBound | 1.3.6.1.4.1.236.11.5.11.55.25.1.3 | Integer32 | read-only | The value of this object gives the upper bound of the size in units of 1024 octets for jobs accepted by the printer. |
| I32 scmPrtIPPJobMediaSheetsCompleted | 1.3.6.1.4.1.236.11.5.11.55.25.1.21 | Integer32 | read-only | The value of this object gives the number of pages printed for the current job. |
| I32 scmPrtIPPJobMediaSheetsSupportedLBound | 1.3.6.1.4.1.236.11.5.11.55.25.1.6 | Integer32 | read-only | The value of this object gives the lower bound of the number of pages printed for a job. |
| I32 scmPrtIPPJobMediaSheetsSupportedUBound | 1.3.6.1.4.1.236.11.5.11.55.25.1.7 | Integer32 | read-only | The value of this object gives the upper bound of the number of pages printed for a job. |
| INT scmPrtIPPJobSheets | 1.3.6.1.4.1.236.11.5.11.55.25.1.8 | INTEGER | read-write | The value of this object specifies the type of job start/end sheets printed with every IPP job. If the value is standard(1), the printer specific standard job start/end sheets will be printed for each job. |
| I32 scmPrtIPPNumberUp | 1.3.6.1.4.1.236.11.5.11.55.25.1.15 | Integer32 | read-write | The value of this object indicates the number of print images imposed on one side of a page. |
| INT scmPrtIPPNumberUpOptions | 1.3.6.1.4.1.236.11.5.11.55.25.1.16 | INTEGER | read-only | The value of this object will be the bitwise OR of the supported values for numberUp in this printer. |
| INT scmPrtIPPPageRangesSupported | 1.3.6.1.4.1.236.11.5.11.55.25.1.14 | INTEGER | read-write | The value of this object indicates whether printing only a range of pages for IPP jobs is supported. If the value is on(1), printing only specified page ranges of the given IPP job is supported. |
| I32 scmPrtIPPPrintQuality | 1.3.6.1.4.1.236.11.5.11.55.25.1.17 | Integer32 | read-write | The value of this object indicates the print quality that the printer uses for a print job. The value draft(1) means lowest quality available on the printer. Tha value normal(2) means normal or intermediate quality on the printer. The value high(4) means highest quality available on the printer. |
| INT scmPrtIPPPrintQualityOptions | 1.3.6.1.4.1.236.11.5.11.55.25.1.18 | INTEGER | read-only | The value of this object will be the bitwise OR of the supported values for printQuality in this printer. |
| scmPrtIPPSimple | 1.3.6.1.4.1.236.11.5.11.55.25.1 | |||
| scmPrtKS5843 | 1.3.6.1.4.1.236.11.5.11.55.23 | |||
| I32 scmPrtKS5843AutoWrap | 1.3.6.1.4.1.236.11.5.11.55.23.1.9 | Integer32 | read-write | |
| INT scmPrtKS5843AutoWrapOptions | 1.3.6.1.4.1.236.11.5.11.55.23.1.10 | INTEGER | read-only | |
| I32 scmPrtKS5843Code | 1.3.6.1.4.1.236.11.5.11.55.23.1.3 | Integer32 | read-write | |
| INT scmPrtKS5843CodeOptions | 1.3.6.1.4.1.236.11.5.11.55.23.1.4 | INTEGER | read-only | |
| I32 scmPrtKS5843cpi | 1.3.6.1.4.1.236.11.5.11.55.23.1.5 | Integer32 | read-write | |
| INT scmPrtKS5843cpiOptions | 1.3.6.1.4.1.236.11.5.11.55.23.1.6 | INTEGER | read-only | |
| I32 scmPrtKS5843Font | 1.3.6.1.4.1.236.11.5.11.55.23.1.1 | Integer32 | read-write | |
| INT scmPrtKS5843FontOptions | 1.3.6.1.4.1.236.11.5.11.55.23.1.2 | INTEGER | read-only | |
| scmPrtKS5843Group | 1.3.6.1.4.1.236.11.5.11.55.2.3.23 | Description. | ||
| INT scmPrtKS5843Lines | 1.3.6.1.4.1.236.11.5.11.55.23.1.7 | INTEGER | read-write | |
| scmPrtKS5843Simple | 1.3.6.1.4.1.236.11.5.11.55.23.1 | |||
| INT scmPrtKS5843Sitemode | 1.3.6.1.4.1.236.11.5.11.55.23.1.12 | INTEGER | read-write | Each site special Mode except ksc5843 standard |
| INT scmPrtKS5843Topmargin | 1.3.6.1.4.1.236.11.5.11.55.23.1.11 | INTEGER | read-write | |
| INT scmPrtKS5843Zoom | 1.3.6.1.4.1.236.11.5.11.55.23.1.8 | INTEGER | read-write | |
| scmPrtKSSM | 1.3.6.1.4.1.236.11.5.11.55.24 | |||
| I32 scmPrtKSSMAutoWrap | 1.3.6.1.4.1.236.11.5.11.55.24.1.9 | Integer32 | read-write | |
| INT scmPrtKSSMAutoWrapOptions | 1.3.6.1.4.1.236.11.5.11.55.24.1.10 | INTEGER | read-only | |
| I32 scmPrtKSSMCode | 1.3.6.1.4.1.236.11.5.11.55.24.1.3 | Integer32 | read-write | |
| INT scmPrtKSSMCodeOptions | 1.3.6.1.4.1.236.11.5.11.55.24.1.4 | INTEGER | read-only | |
| I32 scmPrtKSSMCPI | 1.3.6.1.4.1.236.11.5.11.55.24.1.5 | Integer32 | read-write | |
| INT scmPrtKSSMCPIOptions | 1.3.6.1.4.1.236.11.5.11.55.24.1.6 | INTEGER | read-only | |
| I32 scmPrtKSSMFont | 1.3.6.1.4.1.236.11.5.11.55.24.1.1 | Integer32 | read-write | |
| INT scmPrtKSSMFontOptions | 1.3.6.1.4.1.236.11.5.11.55.24.1.2 | INTEGER | read-only | |
| scmPrtKSSMGroup | 1.3.6.1.4.1.236.11.5.11.55.2.3.24 | Description. | ||
| INT scmPrtKSSMLines | 1.3.6.1.4.1.236.11.5.11.55.24.1.7 | INTEGER | read-write | |
| scmPrtKSSMSimple | 1.3.6.1.4.1.236.11.5.11.55.24.1 | |||
| INT scmPrtKSSMSiteMode | 1.3.6.1.4.1.236.11.5.11.55.24.1.12 | INTEGER | read-write | |
| INT scmPrtKSSMTopMargin | 1.3.6.1.4.1.236.11.5.11.55.24.1.11 | INTEGER | read-write | |
| INT scmPrtKSSMZoom | 1.3.6.1.4.1.236.11.5.11.55.24.1.8 | INTEGER | read-write | |
| scmPrtMarker | 1.3.6.1.4.1.236.11.5.11.55.17 | |||
| I32 scmPrtMarkerDensity | 1.3.6.1.4.1.236.11.5.11.55.17.1.4 | Integer32 | read-only | It determines the overall density of page |
| INT scmPrtMarkerDensityOptions | 1.3.6.1.4.1.236.11.5.11.55.17.1.5 | INTEGER | read-only | available options of current model |
| INT scmPrtMarkerduplexLeftMargin | 1.3.6.1.4.1.236.11.5.11.55.17.1.9 | INTEGER | read-only | The value of this object gives the left margin on the backside of a page when printing in duplex mode. The actual value used in the printer is the value of this object divided by 10. The unit is inch. |
| INT scmPrtMarkerduplexTopMargin | 1.3.6.1.4.1.236.11.5.11.55.17.1.8 | INTEGER | read-only | The value of this object gives the top margin on the backside of a page when printing in duplex mode. The actual value used in the printer is the value of this object divided by 10. The unit is inch. |
| scmPrtMarkerEntry | 1.3.6.1.4.1.236.11.5.11.55.17.2.1 | not-accessible | Entries may exist in the table for each device index who's device type is printer | |
| scmPrtMarkerGroup | 1.3.6.1.4.1.236.11.5.11.55.2.3.17 | The Marker Group. | ||
| INT scmPrtMarkerLongEdgeBindingMargin | 1.3.6.1.4.1.236.11.5.11.55.17.1.11 | INTEGER | read-only | The value of this object gives the margin left for binding on the long edge of the paper when printing is done in long edge duplex mode. The actual value used in the printer is the value of this object divided by 10. The unit is inch. |
| INT scmPrtMarkerMarginUnit | 1.3.6.1.4.1.236.11.5.11.55.17.1.1 | INTEGER | read-only | |
| I32 scmPrtMarkerResolution | 1.3.6.1.4.1.236.11.5.11.55.17.2.1.2 | Integer32 | read-write | The value of this object gives the current resolution used while printing. The value res300(1) means 300X300 dpi resolution. The value res600(2) means 600X600 dpi resolution. The value res1200(4) means 1200X1200 dpi resolution. |
| INT scmPrtMarkerResolutionOptions | 1.3.6.1.4.1.236.11.5.11.55.17.2.1.3 | INTEGER | read-only | The value of this object will be the bitwise OR of all the supported values for resolution in this printer. |
| INT scmPrtMarkerShortEdgeBindingMargin | 1.3.6.1.4.1.236.11.5.11.55.17.1.10 | INTEGER | read-only | The value of this object gives the margin left for binding on the short edge of the paper when printing is done in short edge duplex mode. The actual value used in the printer is the value of this object divided by 10. The unit is inch. |
| scmPrtMarkerSimple | 1.3.6.1.4.1.236.11.5.11.55.17.1 | |||
| I32 scmPrtMarkerSmetMode | 1.3.6.1.4.1.236.11.5.11.55.17.1.6 | Integer32 | read-only | The value of this object indicates whether the SMET mode is currently enabled. |
| INT scmPrtMarkerSmetModeOptions | 1.3.6.1.4.1.236.11.5.11.55.17.1.7 | INTEGER | read-only | The value of this object will be the bitwise OR of the supported values for smetMode in this printer. |
| I32 scmPrtMarkerSrt | 1.3.6.1.4.1.236.11.5.11.55.17.1.2 | Integer32 | read-write | It determin Samsung Resolution Technology option when it is ON. |
| INT scmPrtMarkerSrtOptions | 1.3.6.1.4.1.236.11.5.11.55.17.1.3 | INTEGER | read-only | available options of current model |
| scmPrtMarkerTable | 1.3.6.1.4.1.236.11.5.11.55.17.2 | not-accessible | ||
| I32 scmPrtMarkerTonerColor | 1.3.6.1.4.1.236.11.5.11.55.17.2.1.4 | Integer32 | read-only | color of Toner |
| OCT scmPrtMarkerTonerColorDescription | 1.3.6.1.4.1.236.11.5.11.55.17.2.1.5 | OCTET STRING | read-only | Description of Toner |
| ORD scmPrtMarkerTonerIndex | 1.3.6.1.4.1.236.11.5.11.55.17.2.1.1 | Ordinal32 | read-only | Index of the Toner number |
| I32 scmPrtMarkerTonerLevel | 1.3.6.1.4.1.236.11.5.11.55.17.2.1.6 | Integer32 | read-only | Indication of Toner remainder |
| I32 scmPrtMarkerTonerOutAction | 1.3.6.1.4.1.236.11.5.11.55.17.1.14 | Integer32 | read-only | The value of this object gives the action taken by the printer when the tonerLow condition occurs. If the value is continue(1), the printer continues to print in spite of the toner being low. If the value is stop(2), the printer stops printing when the toner is low. |
| INT scmPrtMarkerTonerOutActionOptions | 1.3.6.1.4.1.236.11.5.11.55.17.1.15 | INTEGER | read-only | The value of this object will be the bitwise OR of the supported values for tonerLowAction in this printer. |
| I32 scmPrtMarkerTonerSave | 1.3.6.1.4.1.236.11.5.11.55.17.1.12 | Integer32 | read-only | Echo mode option. Echo mode Off Echo mode On |
| I32 scmPrtMarkerTonerSaveOptions | 1.3.6.1.4.1.236.11.5.11.55.17.1.13 | Integer32 | read-only | available options of the model |
| scmPrtMediaPath | 1.3.6.1.4.1.236.11.5.11.55.16 | |||
| scmPrtMIBCompliance | 1.3.6.1.4.1.236.11.5.11.55.2.1 | The compliance statement for agents that implement the printer MIB extension module. | ||
| scmPrtMIBConformance | 1.3.6.1.4.1.236.11.5.11.55.2 | |||
| scmPrtMIBGroups | 1.3.6.1.4.1.236.11.5.11.55.2.3 | |||
| INT scmPrtOperarionMenuClear | 1.3.6.1.4.1.236.11.5.11.55.18.1.2 | INTEGER | read-write | When the value of this object is set to clearMenus(1), the values of all the printer properties in all the menus will be set to default values. |
| scmPrtOperation | 1.3.6.1.4.1.236.11.5.11.55.18 | |||
| scmPrtOperationEntry | 1.3.6.1.4.1.236.11.5.11.55.18.2.1 | not-accessible | ||
| INT scmPrtOperationFuserClean | 1.3.6.1.4.1.236.11.5.11.55.18.1.4 | INTEGER | read-write | When the value of this object is set to fuserClean(2),the printer fuser will be clear |
| INT scmPrtOperationFuserCleanOptions | 1.3.6.1.4.1.236.11.5.11.55.18.1.5 | INTEGER | read-only | The value of this object will be the bitwise OR of the supported values for nfuserClean in this printer. |
| scmPrtOperationGroup | 1.3.6.1.4.1.236.11.5.11.55.2.3.18 | Description. | ||
| ORD scmPrtOperationIndex | 1.3.6.1.4.1.236.11.5.11.55.18.2.1.1 | Ordinal32 | read-only | |
| INT scmPrtOperationJobCancel | 1.3.6.1.4.1.236.11.5.11.55.18.1.1 | INTEGER | read-write | Printer Operation Job Cancel Request |
| INT scmPrtOperationMenuClearOptions | 1.3.6.1.4.1.236.11.5.11.55.18.1.3 | INTEGER | read-only | The value of this object will be the bitwise OR of the supported values for menuClear in this printer. |
| INT scmPrtOperationOpcClean | 1.3.6.1.4.1.236.11.5.11.55.18.1.6 | INTEGER | read-write | When the value of this object is set to opcClean(2),the printer OPC will be clear |
| INT scmPrtOperationOpcCleanOptions | 1.3.6.1.4.1.236.11.5.11.55.18.1.7 | INTEGER | read-only | The value of this object will be the bitwise OR of the supported values for nopcClean in this printer. |
| INT scmPrtOperationPrintBlackOnly | 1.3.6.1.4.1.236.11.5.11.55.18.1.10 | INTEGER | read-write | Description. |
| INT scmPrtOperationPrintFontRequest | 1.3.6.1.4.1.236.11.5.11.55.18.1.9 | INTEGER | read-write | request test printing 1: pcl request 2: ps request 3: ks5843 request 4: kssm request 5: ks5895 request 6: epson requese, 7: opcClean request, 8: fuserClean request, 9: configpage request, 10: kssm request, 11: menuMap request, 12: psFlashDirectory requese, |
| scmPrtOperationSimple | 1.3.6.1.4.1.236.11.5.11.55.18.1 | |||
| scmPrtOperationTable | 1.3.6.1.4.1.236.11.5.11.55.18.2 | not-accessible | ||
| I32 scmPrtOperationTestPrtRequest | 1.3.6.1.4.1.236.11.5.11.55.18.1.8 | Integer32 | read-write | request test printing 1: request |
| scmPrtOutput | 1.3.6.1.4.1.236.11.5.11.55.9 | |||
| scmPrtOutputEntry | 1.3.6.1.4.1.236.11.5.11.55.9.1.1 | not-accessible | Entries may exist for each entry in the prtOutputTable. | |
| I32 scmPrtOutputFinishier | 1.3.6.1.4.1.236.11.5.11.55.9.1.1.51 | Integer32 | read-create | This object declares the printer output finishier. |
| I32 scmPrtOutputFinishierOptions | 1.3.6.1.4.1.236.11.5.11.55.9.1.1.52 | Integer32 | read-create | This object declares the printer output finishier option. options 1. staple 2. punch |
| scmPrtOutputGroup | 1.3.6.1.4.1.236.11.5.11.55.2.3.9 | The output group extension. | ||
| I32 scmPrtOutputNextIndex | 1.3.6.1.4.1.236.11.5.11.55.9.1.1.2 | Integer32 | read-create | The value of prtOutputIndex corresponding to the output subunit which will be used when this output subunit is filled. A value of zero(0) indicates that auto output switching will not occur when this output subunit is filled. |
| SCM scmPrtOutputOffsetStackingType | 1.3.6.1.4.1.236.11.5.11.55.9.1.1.4 | ScmPrtOutputOffsetStackingType | read-create | This object further refines the type of offset stacking from that specified by the object prtOutputOffsetStacking in the Printer MIB. |
| OCT scmPrtOutputPassword | 1.3.6.1.4.1.236.11.5.11.55.9.1.1.3 | OCTET STRING | read-create | This object is used as the password for an Output Tray, e.g. an output mailbox. It is the value that must be entered to open the output tray. |
| ROW scmPrtOutputRowStatus | 1.3.6.1.4.1.236.11.5.11.55.9.1.1.1 | RowStatus | read-create | Manages the status of this conceptual row in the scmPrtOutputTable. |
| scmPrtOutputTable | 1.3.6.1.4.1.236.11.5.11.55.9.1 | not-accessible | This table logically augments the prtOutputTable in the Printer MIB. | |
| CAR scmPrtOutputTrayTimeout | 1.3.6.1.4.1.236.11.5.11.55.9.1.1.6 | Cardinal32 | read-create | Determines how long the printer should wait before sending the printed output to another output destination when the selected or default destination is full. A value of (0) implies 'other' or 'infinite' which translates to this input subunit does not support this feature. |
| PRE scmPrtOutputTrayTimeoutSupport | 1.3.6.1.4.1.236.11.5.11.55.9.1.1.5 | PresentOnOff | read-create | Determines whether the printer should wait before sending the printed output to another output destination when the selected or default destination is full. 'On' indicates that would should wait as specified by scmPrtOutputTrayTimeout. 'Off' indicates this feature is off and should immediately seek to send the printed output to another destination. The value 'other' shall mean not specified. |
| scmPrtPCL | 1.3.6.1.4.1.236.11.5.11.55.22 | |||
| I32 scmPrtPCLAppendCR | 1.3.6.1.4.1.236.11.5.11.55.22.1.8 | Integer32 | read-write | |
| INT scmPrtPCLAppendCROptions | 1.3.6.1.4.1.236.11.5.11.55.22.1.9 | INTEGER | read-only | |
| I32 scmPrtPCLCourier | 1.3.6.1.4.1.236.11.5.11.55.22.1.6 | Integer32 | read-write | |
| INT scmPrtPCLCourierOptions | 1.3.6.1.4.1.236.11.5.11.55.22.1.7 | INTEGER | read-only | |
| scmPrtPCLEntry | 1.3.6.1.4.1.236.11.5.11.55.22.2.1 | not-accessible | ||
| INT scmPrtPCLFont | 1.3.6.1.4.1.236.11.5.11.55.22.1.1 | INTEGER | read-write | |
| INT scmPrtPCLFormLine | 1.3.6.1.4.1.236.11.5.11.55.22.1.3 | INTEGER | read-write | |
| scmPrtPCLGroup | 1.3.6.1.4.1.236.11.5.11.55.2.3.22 | Description. | ||
| ORD scmPrtPCLIndex | 1.3.6.1.4.1.236.11.5.11.55.22.2.1.1 | Ordinal32 | read-only | |
| INT scmPrtPCLLeftMargin | 1.3.6.1.4.1.236.11.5.11.55.22.1.13 | INTEGER | read-write | Left margine of printed page, actual value is a value divided by 10. Basic unit is inch. If Orentation is landscape or reverse landscape, the range is 0 to 99 and if the Orientation is portrait or reverse portrait, the range is 0 to 170. |
| INT scmPrtPCLPitch | 1.3.6.1.4.1.236.11.5.11.55.22.1.4 | INTEGER | read-write | |
| INT scmPrtPCLPointSize | 1.3.6.1.4.1.236.11.5.11.55.22.1.5 | INTEGER | read-write | |
| scmPrtPCLSimple | 1.3.6.1.4.1.236.11.5.11.55.22.1 | |||
| INT scmPrtPCLSymbolSet | 1.3.6.1.4.1.236.11.5.11.55.22.1.2 | INTEGER | read-write | |
| scmPrtPCLTable | 1.3.6.1.4.1.236.11.5.11.55.22.2 | not-accessible | ||
| INT scmPrtPCLTopMargin | 1.3.6.1.4.1.236.11.5.11.55.22.1.12 | INTEGER | read-write | Margine between top and first line of this page ,actuall value of printing is a value divided by 10. basic unit is inch. If Orientation is portrait or reverse portrait, then the range of topMargine is 0 to 99 and if Orientation is landscape or reverse landscape, then range is 0 to 170 |
| I32 scmPrtPCLWideA4 | 1.3.6.1.4.1.236.11.5.11.55.22.1.10 | Integer32 | read-write | |
| INT scmPrtPCLWideA4Options | 1.3.6.1.4.1.236.11.5.11.55.22.1.11 | INTEGER | read-only | |
| scmPrtSerial | 1.3.6.1.4.1.236.11.5.11.55.21 | |||
| INT scmPrtSerialBobuxon | 1.3.6.1.4.1.236.11.5.11.55.21.2.1.4 | INTEGER | read-write | |
| I32 scmPrtSerialBobuxonOptions | 1.3.6.1.4.1.236.11.5.11.55.21.2.1.5 | Integer32 | read-only | The value of this object will be the bitwise OR of the supported values for robuxon in this printer. |
| I32 scmPrtSerialBrOptions | 1.3.6.1.4.1.236.11.5.11.55.21.2.1.3 | Integer32 | read-only | available options of printer |
| scmPrtSerialEntry | 1.3.6.1.4.1.236.11.5.11.55.21.2.1 | not-accessible | ||
| scmPrtSerialGroup | 1.3.6.1.4.1.236.11.5.11.55.2.3.21 | The Serial group. | ||
| ORD scmPrtSerialIndex | 1.3.6.1.4.1.236.11.5.11.55.21.2.1.1 | Ordinal32 | not-accessible | |
| I32 scmPrtSerialNbaudRate | 1.3.6.1.4.1.236.11.5.11.55.21.2.1.2 | Integer32 | read-write | the speed when user use a serial port |
| scmPrtSerialSimple | 1.3.6.1.4.1.236.11.5.11.55.21.1 | |||
| scmPrtSerialTable | 1.3.6.1.4.1.236.11.5.11.55.21.2 | not-accessible |
RFC description
Extends printer management with Samsung-specific output stacking and device configuration features.
Start monitoring Samsung network printers, multifunction printers (MFPs) (consumables/tray/job status extension) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.