RAY3-MIB

All MIBs › RAY3-MIB

Organization: Racom s.r.o

Last Updated: 2019-10-21

Category: Microwave Radio, Racom

Description: Manages Racom RAY3 microwave radio link configuration, antenna alignment, and performance metrics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is RAY3-MIB?

RAY3-MIB is a vendor-specific enterprise MIB from RACOM, a Czech manufacturer of licensed microwave point-to-point/point-to-multipoint radios, covering the RAy3 radio-unit product series used for wireless backhaul links. It exposes basic product identity (productName, serialNumber, unitType, deviceName), software version information, and radio-link/interface status objects including peer/station pairing and Ethernet port link state. It is explicitly built for monitoring hardware and software status of the radio: swVer/swVerRadio report firmware versions on the main unit and radio module, systemStatus and lineStatusII summarize overall unit health and RF/line link condition, and eth1Link/eth2Link report up/down state of the unit's Ethernet ports. There is no indication of dependency on external standard MIBs beyond the base SNMPv2 SMI conventions used to build the enterprise tree. It is deployed by wireless operators and ISPs managing RACOM RAy3 microwave links for backhaul or point-to-point connectivity at outdoor telecom sites, where technicians often start with a RAY3-MIB download to load the definitions into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in RAY3-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

RACOM RAy3 microwave radio link unit

Monitoring Examples

An operator polls systemStatus and lineStatusII on a RAy3 unit to detect a degraded or lost microwave link, cross-checking peerNumber and securePeerMode to confirm the unit is still paired with the correct remote station. A change in swVer or swVerRadio flags an unexpected firmware upgrade/downgrade, while eth1Link or eth2Link dropping to down reveals a cabling or switch-port fault on the Ethernet side feeding the radio.

What Can Be Monitored

system status
radio link/line status
peer/station pairing
main and radio firmware version
Ethernet port link state (eth1/eth2)
secure peer mode

Imported Objects

From RFC1155-SMI

Gauge
IpAddress
enterprises

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-MIB

snmpTraps

OBJECT-IDENTITY

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32
mib-2

From SNMPv2-TC

DateAndTime
TEXTUAL-CONVENTION

How to Use in IPNetwork Monitor

Example using numDisconnect OID:

Select an RACOM RAy3 microwave point-to-point/point-to-multipoint radio link unit as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type numDisconnect into the Find box to locate it in the OID tree, then select it and click OK. It reports the number of drops (disconnecting). On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
access	1.3.6.1.4.1.33555.4.1.6
OPT acm	1.3.6.1.4.1.33555.4.2.1.18	OptionSetting	read-only	ACM option.
alarm	1.3.6.1.4.1.33555.4.1.8
ALA alarmBer	1.3.6.1.4.1.33555.4.1.8.6	AlarmState	read-only	BER alarm state.
ALA alarmEth1Down	1.3.6.1.4.1.33555.4.1.8.8	AlarmState	read-only	Ethernet 1 Link Down alarm state.
ALA alarmEth2Down	1.3.6.1.4.1.33555.4.1.8.9	AlarmState	read-only	Ethernet 2 Link Down alarm state.
ALA alarmMse	1.3.6.1.4.1.33555.4.1.8.13	AlarmState	read-only	MSE alarm state.
ALA alarmNetBitrate	1.3.6.1.4.1.33555.4.1.8.11	AlarmState	read-only	Air Speed below Limit alarm state.
ALA alarmPeerDisconnected	1.3.6.1.4.1.33555.4.1.8.7	AlarmState	read-only	Peer disconnect alarm state.
ALA alarmRss	1.3.6.1.4.1.33555.4.1.8.4	AlarmState	read-only	RSS alarm state.
ALA alarmTemperature	1.3.6.1.4.1.33555.4.1.8.1	AlarmState	read-only	Temperature alarm state.
ALA alarmVoltageHigh	1.3.6.1.4.1.33555.4.1.8.3	AlarmState	read-only	High voltage alarm state.
ALA alarmVoltageLow	1.3.6.1.4.1.33555.4.1.8.2	AlarmState	read-only	Low voltage alarm state.
ALA alarmWifiOn	1.3.6.1.4.1.33555.4.1.8.12	AlarmState	read-only	WiFi Host Access Point on.
OPT atpc	1.3.6.1.4.1.33555.4.2.1.19	OptionSetting	read-only	ATPC option.
OPT autonego	1.3.6.1.4.1.33555.4.2.2.1.1.4	OptionSetting	read-only	Ethernet autonego.
I32 ber	1.3.6.1.4.1.33555.4.3.2.11	Integer32	read-only	Bit Error Rate (BER) multiplied by 10^9.
INT channelArrangement	1.3.6.1.4.1.33555.4.2.1.16	INTEGER	read-only	Channel arrangement.
chassis	1.3.6.1.4.1.33555.4.1.4
STR deviceName	1.3.6.1.4.1.33555.4.1.2.1	DisplayStringRaw	read-only	Station name.
INT duplex	1.3.6.1.4.1.33555.4.2.2.1.1.2	INTEGER	read-only	Ethernet duplex.
egressQueue	1.3.6.1.4.1.33555.4.4.3
SER eth1Link	1.3.6.1.4.1.33555.4.1.3.9	ServiceState	read-only	Ethernet 1 link status.
I32 eth2InThroughput	1.3.6.1.4.1.33555.4.3.3.3	Integer32	read-only	Input Ethernet 2 data port throughput in kbps.
SER eth2Link	1.3.6.1.4.1.33555.4.1.3.10	ServiceState	read-only	Ethernet 2 link status.
I32 eth2OutThroughput	1.3.6.1.4.1.33555.4.3.3.4	Integer32	read-only	Output Ethernet 2 data port throughput in kbps.
ethernet	1.3.6.1.4.1.33555.4.3.3
I32 ethInThroughput	1.3.6.1.4.1.33555.4.3.3.1	Integer32	read-only	Input Ethernet 1 data port throughput in kbps.
I32 ethOutThroughput	1.3.6.1.4.1.33555.4.3.3.2	Integer32	read-only	Output Ethernet 1 data port throughput in kbps.
INT flowControl	1.3.6.1.4.1.33555.4.2.2.1.1.7	INTEGER	read-only	Ethernet flow control.
STR frequencyTable	1.3.6.1.4.1.33555.4.2.1.20	DisplayStringRaw	read-only	Current frequency table name.
OPT httpd	1.3.6.1.4.1.33555.4.1.6.3	OptionSetting	read-only	Management interface: HTTP.
ifEth	1.3.6.1.4.1.33555.4.2.2
ifEthEntry	1.3.6.1.4.1.33555.4.2.2.1.1		not-accessible	Ethernet interface entry.
ifEthTable	1.3.6.1.4.1.33555.4.2.2.1		not-accessible	List of Ethernet interfaces.
ifRadio	1.3.6.1.4.1.33555.4.2.1
info	1.3.6.1.4.1.33555.4.1.2
interface	1.3.6.1.4.1.33555.4.2
IP ip	1.3.6.1.4.1.33555.4.1.6.4	IpAddress	read-only	Management interface: IP address.
INT lineStatusII	1.3.6.1.4.1.33555.4.1.3.8	INTEGER	read-only	Radio link status.
TIK linkUptime	1.3.6.1.4.1.33555.4.3.2.10	TimeTicks	read-only	Current radio link uptime.
ADR mac	1.3.6.1.4.1.33555.4.1.6.5	PhysAddressRaw	read-only	Management interface: MAC address.
OPT managementVlan	1.3.6.1.4.1.33555.4.1.6.6	OptionSetting	read-only	Management interface: VLAN on/off.
I32 managementVlanId	1.3.6.1.4.1.33555.4.1.6.7	Integer32	read-only	Management interface: VLAN ID.
OPT matching	1.3.6.1.4.1.33555.4.2.1.11	OptionSetting	read-only	Channel matching.
I32 maxNetBitrate	1.3.6.1.4.1.33555.4.2.1.14	Integer32	read-only	Maximum net bitrate in Mbps.
INT mdix	1.3.6.1.4.1.33555.4.2.2.1.1.3	INTEGER	read-only	Ethernet MDI-X / MDI.
TEN mse	1.3.6.1.4.1.33555.4.3.2.12	Tenths	read-only	Receiving MSE indicator in thnths of dB.
I32 netBitrate	1.3.6.1.4.1.33555.4.2.1.13	Integer32	read-only	Current net bitrate in kbps.
C32 numDisconnectEx	1.3.6.1.4.1.33555.4.3.2.8	Counter32	read-only	Number of drops (disconnecting).
G32 peerNumber	1.3.6.1.4.1.33555.4.1.3.3	Gauge32	read-only	Peer station serial number.
product	1.3.6.1.4.1.33555.4.1.1
STR productName	1.3.6.1.4.1.33555.4.1.1.1	DisplayStringRaw	read-only	Product name.
racom	1.3.6.1.4.1.33555			The MIB module defines management objects for RAy product series. Revision 201909200000Z.
radio	1.3.6.1.4.1.33555.4.3.2
ray3	1.3.6.1.4.1.33555.4
ray3Traps	1.3.6.1.4.1.33555.4.12
ray3TrapsPrefix	1.3.6.1.4.1.33555.4.12.0
THO reliability	1.3.6.1.4.1.33555.4.3.2.9	Thousandths	read-only	Reliability in thousandths of %.
I32 rfPowerConfigured	1.3.6.1.4.1.33555.4.2.1.12	Integer32	read-only	Configured RF Power in dBm.
I32 rfPowerCurrent	1.3.6.1.4.1.33555.4.2.1.17	Integer32	read-only	Current RF Power in dBm.
TEN rss	1.3.6.1.4.1.33555.4.3.2.1	Tenths	read-only	Receiving RSS indicator in tenths of dBm.
I32 rxBandwidthKHz	1.3.6.1.4.1.33555.4.2.1.21	Integer32	read-only	Radio Rx channel bandwidth in kHz.
STR rxChannel	1.3.6.1.4.1.33555.4.2.1.1	DisplayStringRaw	read-only	Receiver channel ID.
G32 rxFreq	1.3.6.1.4.1.33555.4.2.1.3	Gauge32	read-only	Receiver frequency in kHz.
STR rxModulation	1.3.6.1.4.1.33555.4.2.1.5	DisplayStringRaw	read-only	Rx modulation text ID.
MOD rxModulationIndex	1.3.6.1.4.1.33555.4.2.1.7	ModulationList	read-only	Rx modulation index.
OPT securePeerMode	1.3.6.1.4.1.33555.4.1.3.7	OptionSetting	read-only	Secure peer mode.
G32 serialNumber	1.3.6.1.4.1.33555.4.1.1.2	Gauge32	read-only	Product serial number.
I32 speed	1.3.6.1.4.1.33555.4.2.2.1.1.1	Integer32	read-only	Ethernet speed.
OPT speedGuard	1.3.6.1.4.1.33555.4.4.3.2	OptionSetting	read-only	Speed guard feature on/off.
INT sshd	1.3.6.1.4.1.33555.4.1.6.1	INTEGER	read-only	Management interface: SSH.
station	1.3.6.1.4.1.33555.4.1
statistic	1.3.6.1.4.1.33555.4.3
status	1.3.6.1.4.1.33555.4.1.3
switch	1.3.6.1.4.1.33555.4.4
STR swVer	1.3.6.1.4.1.33555.4.1.2.2	DisplayStringRaw	read-only	Firmware version.
STR swVerRadio	1.3.6.1.4.1.33555.4.1.2.3	DisplayStringRaw	read-only	Radio firmware version.
system	1.3.6.1.4.1.33555.4.1.5
INT systemStatus	1.3.6.1.4.1.33555.4.1.3.1	INTEGER	read-only	Unit status.
OPT telnetd	1.3.6.1.4.1.33555.4.1.6.2	OptionSetting	read-only	Management interface: Telnet.
HUN temperatureModem	1.3.6.1.4.1.33555.4.1.4.1	Hundredths	read-only	Modem temperature in hundredths of Celsius.
HUN temperatureRadio	1.3.6.1.4.1.33555.4.1.4.2	Hundredths	read-only	Radio temperature in hundredths of Celsius.
TIK timeAllConnect	1.3.6.1.4.1.33555.4.3.2.5	TimeTicks	read-only	Overall link uptime.
TIK timeAllDisconnect	1.3.6.1.4.1.33555.4.3.2.6	TimeTicks	read-only	Overall link downtime.
TIK timeMaxDisconnect	1.3.6.1.4.1.33555.4.3.2.7	TimeTicks	read-only	The longest drop (disconnecting).
NTF tr3AirConnect	1.3.6.1.4.1.33555.4.12.0.8			Air line connected after being disconnected.
NTF tr3AirDisconnect	1.3.6.1.4.1.33555.4.12.0.7			Air line disconnected.
NTF tr3BerAlarm	1.3.6.1.4.1.33555.4.12.0.6			BER exceeded the threshold.
NTF tr3Eth1LinkDown	1.3.6.1.4.1.33555.4.12.0.9			Local station Ethernet 1 link Up/Down.
NTF tr3Eth21LinkDown	1.3.6.1.4.1.33555.4.12.0.10			Local station Ethernet 2 link Up/Down.
NTF tr3EventAirCapacity	1.3.6.1.4.1.33555.4.12.0.101			Air channel capacity changed.
NTF tr3MseAlarm	1.3.6.1.4.1.33555.4.12.0.5			MSE exceeded the threshold.
NTF tr3NetBitrate	1.3.6.1.4.1.33555.4.12.0.11			Air speed below threshold.
NTF tr3RssAlarm	1.3.6.1.4.1.33555.4.12.0.4			RSS exceeded the threshold.
NTF tr3TemperatureAlarm	1.3.6.1.4.1.33555.4.12.0.1			Temperature exceeded the threshold.
NTF tr3VoltageHighAlarm	1.3.6.1.4.1.33555.4.12.0.3			Supply voltage above maximal threshold.
NTF tr3VoltageLowAlarm	1.3.6.1.4.1.33555.4.12.0.2			Supply voltage below minimal threshold.
NTF tr3WifiOn	1.3.6.1.4.1.33555.4.12.0.12			WiFi Host Access Point is on.
I32 txBandwidthKHz	1.3.6.1.4.1.33555.4.2.1.15	Integer32	read-only	Radio Tx channel bandwidth in kHz.
STR txChannel	1.3.6.1.4.1.33555.4.2.1.2	DisplayStringRaw	read-only	Transceiver channel ID.
G32 txFreq	1.3.6.1.4.1.33555.4.2.1.4	Gauge32	read-only	Transceiver frequency in kHz.
STR txModulation	1.3.6.1.4.1.33555.4.2.1.6	DisplayStringRaw	read-only	Tx modulation text ID.
MOD txModulationIndex	1.3.6.1.4.1.33555.4.2.1.8	ModulationList	read-only	Tx modulation index.
STR unitType	1.3.6.1.4.1.33555.4.1.1.3	DisplayStringRaw	read-only	Station type (L or H).
INT useCpu	1.3.6.1.4.1.33555.4.1.5.1	INTEGER	read-only	System use CPU in %.
INT useLogStorage	1.3.6.1.4.1.33555.4.1.5.3	INTEGER	read-only	Use storage for log in %.
INT useMemory	1.3.6.1.4.1.33555.4.1.5.2	INTEGER	read-only	System use memory in %.
INT voltageSource	1.3.6.1.4.1.33555.4.1.4.4	INTEGER	read-only	Source of supply voltage.
TEN voltageUnit	1.3.6.1.4.1.33555.4.1.4.3	Tenths	read-only	Power supply voltage in tenths of Volts (V).
INT wifiHAP	1.3.6.1.4.1.33555.4.1.6.8	INTEGER	read-only	Management interface: WiFi Host Access Point.

RFC description

Manages Racom RAy product series network equipment with service and alarm state monitoring.

Start monitoring RACOM RAy3 microwave point-to-point/point-to-multipoint radio link unit with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download RAY3-MIB