PRVT-MPLS-IF-MIB

All MIBs › PRVT-MPLS-IF-MIB

Organization: BATM Advanced Communication

Last Updated: 2008-01-01

Category: MPLS and Traffic Engineering

Description: Manages BATM Advanced Communication MPLS-enabled interface configuration, label space, and per-interface MPLS state.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is PRVT-MPLS-IF-MIB?

PRVT-MPLS-IF-MIB is a BATM Advanced Communications proprietary MIB that configures MPLS- and RSVP-enabled interface parameters on their Carrier Ethernet switch products, including per-interface MPLS routing protocol and address associations. It exposes route protocol and route address tables tied to MPLS-enabled interfaces, letting operators see which routing protocol and address bindings are associated with a given MPLS interface. This supports monitoring of MPLS interface configuration correctness and label-space/protocol state, which is useful for diagnosing MPLS forwarding or RSVP signaling problems at the interface level. It likely complements standard MPLS and RSVP-TE MIBs (e.g., MPLS-LSR-MIB) for full label-switching visibility, though it is a vendor-private extension rather than a full replacement. It is deployed on BATM Advanced Communications MPLS-capable Carrier Ethernet switches in provider aggregation and backbone networks, where PRVT-MPLS-IF-MIB SNMP monitoring helps diagnose MPLS forwarding or RSVP signaling problems at the interface level.

IPNetwork Monitor allows you to monitor SNMP objects defined in PRVT-MPLS-IF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

BATM Advanced Communications MPLS-capable Carrier Ethernet switches

Monitoring Examples

An operator can poll prvtMplsRouteProtocolTable via prvtMplsRouteProtocolEntry to confirm which routing protocol is bound to a given MPLS-enabled interface, and cross-reference prvtMplsRouteAddressTable/prvtMplsRouteAddressEntry to verify the correct IP address is associated with that interface's MPLS routing context. A mismatch between expected and actual protocol bindings here would point to a misconfigured MPLS interface preventing proper label distribution.

What Can Be Monitored

MPLS interface routing protocol binding
MPLS interface address association
per-interface MPLS/RSVP configuration state

Imported Objects

From IF-MIB

ifEntry	OBJECT-TYPE
ifIndex	OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddress

From PRVT-CR-LDP-MIB

mpls	OBJECT-IDENTITY

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
prvtMPLSIfMib	1.3.6.1.4.1.738.1.6.5.6			This module includes configuration parameters for MPLS and RSVP interface specific parameters.
prvtMPLSIfaceObjs	1.3.6.1.4.1.738.1.6.5.6.1
prvtMplsIfaceTable	1.3.6.1.4.1.738.1.6.5.6.1.1		not-accessible	This table contains object for configuring MPLS and LDP interface specific parameters.
prvtMplsIfaceEntry	1.3.6.1.4.1.738.1.6.5.6.1.1.1		not-accessible	The MPLS/LDP configuration of an IP interface.
T/F ifaceMplsEnable	1.3.6.1.4.1.738.1.6.5.6.1.1.1.1	TruthValue	read-write	Enable or disable MPLS on this interface.
T/F ifaceMplsPHPEnable	1.3.6.1.4.1.738.1.6.5.6.1.1.1.2	TruthValue	read-write	Enable or disable Penultimate Hop Popping on this interface.
I32 ifaceMplsIngressLblRangeLow	1.3.6.1.4.1.738.1.6.5.6.1.1.1.3	Integer32	read-write	This is the lower border of the Ingress Lable Range for this interface.
I32 ifaceMplsIngressLblRangeHigh	1.3.6.1.4.1.738.1.6.5.6.1.1.1.4	Integer32	read-write	This is the higher border of the Ingress Lable Range for this interface.
I32 ifaceMplsEgressLblRangeLow	1.3.6.1.4.1.738.1.6.5.6.1.1.1.5	Integer32	read-write	This is the lower border of the Egress Lable Range for this interface.
I32 ifaceMplsEgressLblRangeHigh	1.3.6.1.4.1.738.1.6.5.6.1.1.1.6	Integer32	read-write	This is the higher border of the Egress Lable Range for this interface.
I32 ifaceMplsLdpHelloHoldTimer	1.3.6.1.4.1.738.1.6.5.6.1.1.1.7	Integer32	read-write	LDP Hello Hold Time.
I32 ifaceMplsLdpKeepaliveHoldTimer	1.3.6.1.4.1.738.1.6.5.6.1.1.1.8	Integer32	read-write	LDP Hello Keep-alive Time.
T/F ifaceMplsLdpUseGlobalLabelSpace	1.3.6.1.4.1.738.1.6.5.6.1.1.1.9	TruthValue	read-write	Default value is true and correct value is true.
prvtRsvpIfaceTable	1.3.6.1.4.1.738.1.6.5.6.1.2		not-accessible	This table contains object for configuring RSVP interface specific parameters.
prvtRsvpIfaceEntry	1.3.6.1.4.1.738.1.6.5.6.1.2.1		not-accessible	The MPLS/LDP configuration of an IP interface.
I32 ifaceRsvpRefreshInterval	1.3.6.1.4.1.738.1.6.5.6.1.2.1.1	Integer32	read-write	The RSVP value, R, which is used to set the average interval between refresh path and resv messages.
I32 ifaceRsvpRefreshMultiple	1.3.6.1.4.1.738.1.6.5.6.1.2.1.2	Integer32	read-write	The RSVP value, K, which is the number of unresponded Path or Resv refresh attempts which must be made, spaced by the refresh interval before the state is deemed to have timed out.
I32 ifaceRsvpSlewNumerator	1.3.6.1.4.1.738.1.6.5.6.1.2.1.3	Integer32	read-write	The numerator of the fraction, SlewMax, which is the maximum allowable increase in the refresh interval, R, to prevent state timeout while changing R. R is increased by this fraction until it reaches the new desired value.
I32 ifaceRsvpSlewDenom	1.3.6.1.4.1.738.1.6.5.6.1.2.1.4	Integer32	read-write	The denominator of the fraction, SlewMax, which is the maximum allowable increase in the refresh interval, R, to prevent state timeout while changing R. R is increased by this fraction until it reaches the new desired value.
I32 ifaceRsvpBlockadeMultiple	1.3.6.1.4.1.738.1.6.5.6.1.2.1.5	Integer32	read-write	The RSVP value, Kb, which is the number of refresh timeout periods after which blockade state is deleted.
I32 ifaceRsvpNotifyRRDecay	1.3.6.1.4.1.738.1.6.5.6.1.2.1.6	Integer32	read-write	The percentage increase in the rapid retransmission interval for each consecutive unacknowledged RSVP Notify message. A value of 0 indicates a constant retransmission rate.
I32 ifaceRsvpNotifyRRInterval	1.3.6.1.4.1.738.1.6.5.6.1.2.1.7	Integer32	read-write	The interval in milliseconds before a Notify message is first resent if no acknowledgement is received.
I32 ifaceRsvpNotifyRRLimit	1.3.6.1.4.1.738.1.6.5.6.1.2.1.8	Integer32	read-write	The maximum number of times a Notify message is resent if no acknowledgement is received.
I32 ifaceRsvpHelloInterval	1.3.6.1.4.1.738.1.6.5.6.1.2.1.9	Integer32	read-write	The interval between sending consecutive Hello messages.
I32 ifaceRsvpHelloDecay	1.3.6.1.4.1.738.1.6.5.6.1.2.1.10	Integer32	read-write	Percentage increase of hello interval after each Hello message sent when the hello session with the neighbor has timed out.
U32 ifaceRsvpHelloTolerance	1.3.6.1.4.1.738.1.6.5.6.1.2.1.11	Unsigned32	read-write	The number of hello periods which may pass without receiving a successful Hello message from a partner before the Hello session times out.
U32 ifaceRsvpHelloPersist	1.3.6.1.4.1.738.1.6.5.6.1.2.1.12	Unsigned32	read-write	The number of hello periods which may pass after the Hello session times out before Hello messages cease.
I32 ifaceRsvpHelloTTL	1.3.6.1.4.1.738.1.6.5.6.1.2.1.13	Integer32	read-write	The Time To Live that will be set in the IP header of all Hello packets sent to the neighbor associated with this interface.
prvtMPLSRouteObjs	1.3.6.1.4.1.738.1.6.5.6.2
prvtMplsRouteProtocolTable	1.3.6.1.4.1.738.1.6.5.6.2.1		not-accessible	This table contains for configuring the egress and ingress routes for LDP label packets. It supports all CLI route types - bgp, isis, ospf, rip, static, kernel and connected.
prvtMplsRouteProtocolEntry	1.3.6.1.4.1.738.1.6.5.6.2.1.1		not-accessible	An entry in the table represents the configuration of a particular route type for ingress or egress.
INT prvtMplsRouteDirection	1.3.6.1.4.1.738.1.6.5.6.2.1.1.1	INTEGER	read-only	The direction of the route that will be used to receive or send LDP packets.
INT prvtMplsRouteType	1.3.6.1.4.1.738.1.6.5.6.2.1.1.2	INTEGER	read-only	The type of the route which will be used to send or receive LDP packets.
ROW prvtMplsRouteRowStatus	1.3.6.1.4.1.738.1.6.5.6.2.1.1.3	RowStatus	read-create	This object is used to create an entry in the table. Only createAndGo(4) should be used.
prvtMplsRouteAddressTable	1.3.6.1.4.1.738.1.6.5.6.2.2		not-accessible	This table contains for configuring the egress and ingress routes for LDP label packets. It supports all CLI route types - bgp, isis, ospf, rip, static, kernel and connected.
prvtMplsRouteAddressEntry	1.3.6.1.4.1.738.1.6.5.6.2.2.1		not-accessible	An entry in the table represents the configuration of a particular route type for ingress or egress.
INT prvtMplsAddressDirection	1.3.6.1.4.1.738.1.6.5.6.2.2.1.1	INTEGER	read-only	The direction of the route that will be used to receive or send LDP packets.
IP prvtMplsAddressIPAddr	1.3.6.1.4.1.738.1.6.5.6.2.2.1.2	InetAddress	read-only	The IP address of the route that will be used to send or receive LDP packets.
I32 prvtMplsAddressMask	1.3.6.1.4.1.738.1.6.5.6.2.2.1.3	Integer32	read-only	The mask for the IP address of the route that will be used to send or receive LDP packets.
ROW prvtMplsAddressRowStatus	1.3.6.1.4.1.738.1.6.5.6.2.2.1.4	RowStatus	read-create	This object is used to create an entry in the table. Only createAndGo(4) should be used.

RFC description

Configures MPLS and RSVP interface-specific parameters on T-Metro Switches.

Start monitoring BATM Advanced Communications MPLS-capable Carrier Ethernet switches (MPLS/RSVP interface config) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download PRVT-MPLS-IF-MIB

What Is PRVT-MPLS-IF-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description