PBI-4000P-5000P-MIB

All MIBs › PBI-4000P-5000P-MIB

Organization: PBI

Last Updated: 2006-09-13

Description: MIB for PBI (China) 4000P/5000P broadcast IRD/decoder appliances, managing satellite/cable/terrestrial tuner inputs and ASI/SDI/Ethernet output configuration

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is PBI-4000P-5000P-MIB?

PBI-4000P-5000P-MIB is a vendor-specific MIB for PBI (China)'s 4000P/5000P series broadcast integrated receiver-decoder (IRD) appliances, which receive satellite, cable, or terrestrial signals and output decoded video/audio over ASI, SDI, and Ethernet interfaces. It is intended to expose tuner input configuration/status and output port configuration for these broadcast decoders. Its monitoring role would cover device operational status such as tuner lock/signal state, output port status, and possibly general device health (power, temperature) typical of broadcast headend equipment, though no specific object names were captured in this extract to confirm exact coverage. It is likely a self-contained vendor module with limited dependency on standard IETF MIBs beyond basic SNMP conventions. It is deployed in broadcast headends and cable/satellite/terrestrial signal distribution facilities using PBI 4000P/5000P decoders, where PBI-4000P-5000P-MIB SNMP monitoring would be expected to track tuner lock and output status.

IPNetwork Monitor allows you to monitor SNMP objects defined in PBI-4000P-5000P-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

PBI 4000P/5000P broadcast IRD/decoder appliance

Monitoring Examples

No object names were provided in this extract, so a specific monitoring scenario cannot be grounded in real object names for this module; broadcast IRD/decoder MIBs of this kind are typically polled for tuner lock/signal status and output port state to detect a lost input signal or failed output. Because sample_objects is empty, further technical detail would require reviewing the MIB source directly.

What Can Be Monitored

tuner input signal/lock status
output port (ASI/SDI/Ethernet) status
device configuration

Imported Objects

From PBI-MAIN-MIB

mg	OBJECT-IDENTITY

From PBI-MGSYSTEM-MIB

basicInfo

OBJECT-IDENTITY

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
enterprises

From SNMPv2-TC

DisplayString
TruthValue

How to Use in IPNetwork Monitor

Example using tunerLock OID:

Select a PBI 4000P/5000P broadcast IRD/decoder appliance as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type tunerLock into the Find box to locate it in the OID tree, then select it and click OK. It reports tuner Lock? yes: 1,no: 0. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if the value is anything other than '1 (locked)', since that indicates the condition this object reports has changed to one worth investigating. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
p4000_p5000	1.3.6.1.4.1.1070.3.1.1.104			private infomation of 4000P&5000P
inputStatus	1.3.6.1.4.1.1070.3.1.1.104.1
tunerStatusEntry	1.3.6.1.4.1.1070.3.1.1.104.1.1
INT tunerLockEx	1.3.6.1.4.1.1070.3.1.1.104.1.1.1	INTEGER	read-only	tuner Lock? yes: 1,no: 0
INT tunerPacketLen	1.3.6.1.4.1.1070.3.1.1.104.1.1.2	INTEGER	read-only	packet length: 188 or 204
INT tunerTotalBitrate	1.3.6.1.4.1.1070.3.1.1.104.1.1.3	INTEGER	read-only	total bit Rate size: from 0 to 100Mbps
INT tunerValidBitrate	1.3.6.1.4.1.1070.3.1.1.104.1.1.4	INTEGER	read-only	valid Bit rate: from 0 to 100Mbps
INT tunerQuality	1.3.6.1.4.1.1070.3.1.1.104.1.1.5	INTEGER	read-only	tuner quality signal monitoring
INT tunerStrength	1.3.6.1.4.1.1070.3.1.1.104.1.1.6	INTEGER	read-only	tuner signal strength
INT tunerBER	1.3.6.1.4.1.1070.3.1.1.104.1.1.7	INTEGER	read-only	tuner signal BER
INT tunerCN	1.3.6.1.4.1.1070.3.1.1.104.1.1.8	INTEGER	read-only	tuner carrier noise
INT tunerEbNo	1.3.6.1.4.1.1070.3.1.1.104.1.1.9	INTEGER	read-only	tuner Eb/No
asiStatusEntry	1.3.6.1.4.1.1070.3.1.1.104.1.2
INT asiLock	1.3.6.1.4.1.1070.3.1.1.104.1.2.1	INTEGER	read-only	ASI Lock? yes: 1,no: 0
INT asiPacketLen	1.3.6.1.4.1.1070.3.1.1.104.1.2.2	INTEGER	read-only	packet length: 188 or 204
INT asiTotalBitrate	1.3.6.1.4.1.1070.3.1.1.104.1.2.3	INTEGER	read-only	total bit Rate size: from 0 to 100Mbps
INT asiValidBitrate	1.3.6.1.4.1.1070.3.1.1.104.1.2.4	INTEGER	read-only	valid Bit rate: from 0 to 100Mbps
INT asiIndex	1.3.6.1.4.1.1070.3.1.1.104.1.2.5	INTEGER	read-write	specify which ASI input
ethernetInStatusEntry	1.3.6.1.4.1.1070.3.1.1.104.1.3
INT ethernetInLock	1.3.6.1.4.1.1070.3.1.1.104.1.3.1	INTEGER	read-only	DS3 Lock? yes: 1,no: 0
INT ethernetInPacketLen	1.3.6.1.4.1.1070.3.1.1.104.1.3.2	INTEGER	read-only	packet length: 188 or 204
INT ethernetInTotalBitrate	1.3.6.1.4.1.1070.3.1.1.104.1.3.3	INTEGER	read-only	total bit Rate size: from 0 to 100Mbps
INT linkStatus	1.3.6.1.4.1.1070.3.1.1.104.1.3.4	INTEGER	read-only	0:none, 1:10M, 2:100M
tunerType	1.3.6.1.4.1.1070.3.1.1.104.2
INT typeSel	1.3.6.1.4.1.1070.3.1.1.104.2.1	INTEGER	read-only	tuner type
INT channel	1.3.6.1.4.1.1070.3.1.1.104.2.2	INTEGER	read-write	tuner channel
tuner_sInput	1.3.6.1.4.1.1070.3.1.1.104.3
INT lnbFrequency	1.3.6.1.4.1.1070.3.1.1.104.3.1	INTEGER	read-write	LNB frequency
INT satFrequency	1.3.6.1.4.1.1070.3.1.1.104.3.2	INTEGER	read-write	Tuner frequency or centre_frequency for the transmission expressed in MHz, its value range: from 950MHz to 2150 MHz
INT symbolRate	1.3.6.1.4.1.1070.3.1.1.104.3.3	INTEGER	read-write	Tuner symbol rate in symbols per second,its value range: from 0kb/s to 45000kb/s
INT lnbVoltage	1.3.6.1.4.1.1070.3.1.1.104.3.4	INTEGER	read-write	Tuner power, Option: 0v,13v,18v
INT lnb22KHz	1.3.6.1.4.1.1070.3.1.1.104.3.5	INTEGER	read-write	Tuner 22 KHz, option: off or on
INT disEqc	1.3.6.1.4.1.1070.3.1.1.104.3.6	INTEGER	read-write	Tuner diseqc, option: 0:DisEqc Off1:PortA2:PortB3:PortC4:PortD
tuner_cInput	1.3.6.1.4.1.1070.3.1.1.104.4
INT constellation	1.3.6.1.4.1.1070.3.1.1.104.4.1	INTEGER	read-write	LNB frequency
INT cableFrequency	1.3.6.1.4.1.1070.3.1.1.104.4.2	INTEGER	read-write	Cable frequency, its value range: from 48000KHz to 862000KHz
INT cableSymbolRate	1.3.6.1.4.1.1070.3.1.1.104.4.3	INTEGER	read-write	The symbol rate in symbols per second, its value range: from 2000kb/s to 7000kb/s
tuner_tInput	1.3.6.1.4.1.1070.3.1.1.104.5
INT terFrequency	1.3.6.1.4.1.1070.3.1.1.104.5.1	INTEGER	read-write	terrestrial frequency: its value range: from 0kb/s to 1000000kb/s
INT bandWidth	1.3.6.1.4.1.1070.3.1.1.104.5.2	INTEGER	read-write	terrestrial band width,option: 0-6MHz; 1-7MHz; 2-8MHz
outputSel	1.3.6.1.4.1.1070.3.1.1.104.6
INT output2sel	1.3.6.1.4.1.1070.3.1.1.104.6.1	INTEGER	read-write	output 2 select
INT decoderOutChannel	1.3.6.1.4.1.1070.3.1.1.104.6.2	INTEGER	read-write	specify decoder out channel
INT ciOutChannel	1.3.6.1.4.1.1070.3.1.1.104.6.3	INTEGER	read-write	specify ci out channel
INT filterOutChannel	1.3.6.1.4.1.1070.3.1.1.104.6.4	INTEGER	read-write	specify filter out channel
INT muxOutChannel	1.3.6.1.4.1.1070.3.1.1.104.6.5	INTEGER	read-write	specify mux out channel
asiOutput	1.3.6.1.4.1.1070.3.1.1.104.7
asi1OutputEntry	1.3.6.1.4.1.1070.3.1.1.104.7.1
INT sourceSel1	1.3.6.1.4.1.1070.3.1.1.104.7.1.1	INTEGER	read-write	select source, qpsk:0, asi:1, ds3:2
INT packageLength1	1.3.6.1.4.1.1070.3.1.1.104.7.1.2	INTEGER	read-write	package lengh, 188 or 204
INT outBitRate	1.3.6.1.4.1.1070.3.1.1.104.7.1.3	INTEGER	read-write	out BitRate, range: from 0~150000Kbps
INT muxType	1.3.6.1.4.1.1070.3.1.1.104.7.1.4	INTEGER	read-write	set Mux Type,option: 0:ASI TV,QPSK EMM CAT; 1:ASI TV,IP EMM; 2:ASI TV,IP EMM CAT; 3:QPSK TV,ASI EMM CAT; 4:QPSK TV,IP EMM CAT
asi2OutputEntry	1.3.6.1.4.1.1070.3.1.1.104.7.2
INT sourceSel2	1.3.6.1.4.1.1070.3.1.1.104.7.2.1	INTEGER	read-write	select source, qpsk:0, asi:1, ds3:2
INT packageLength2	1.3.6.1.4.1.1070.3.1.1.104.7.2.2	INTEGER	read-write	package lengh, 188 or 204
sdiOutput	1.3.6.1.4.1.1070.3.1.1.104.8
INT audioDID	1.3.6.1.4.1.1070.3.1.1.104.8.1	INTEGER	read-write	options: group 1, group 2, group 3, group 4
INT embAudios	1.3.6.1.4.1.1070.3.1.1.104.8.2	INTEGER	read-write	options: none, one, two, one&two
decoderOutput	1.3.6.1.4.1.1070.3.1.1.104.9
programOutputEntry	1.3.6.1.4.1.1070.3.1.1.104.9.1
INT inputChannel	1.3.6.1.4.1.1070.3.1.1.104.9.1.1	INTEGER	read-write	options: qpsk, asi, ds3
STR programNumber	1.3.6.1.4.1.1070.3.1.1.104.9.1.2	DisplayString	read-write	select a program to 4000P and decode it,
videoOutputEntry	1.3.6.1.4.1.1070.3.1.1.104.9.2
INT videoStandard	1.3.6.1.4.1.1070.3.1.1.104.9.2.1	INTEGER	read-write	Decoder status 4 modes :PAL/AUTO/SECAM/NTSC
INT screen	1.3.6.1.4.1.1070.3.1.1.104.9.2.2	INTEGER	read-write	Decoder status screen display: 4:3 Letterbox/4:3 Full/16:9 Full
STR dvbSubtitleLang	1.3.6.1.4.1.1070.3.1.1.104.9.2.3	DisplayString	read-write	Decoder status DVB subtitle language 3 characters
STR ebuSubtitleLang	1.3.6.1.4.1.1070.3.1.1.104.9.2.4	DisplayString	read-write	Decoder status EBU subtitle language 3 characters
INT subtitlePriority	1.3.6.1.4.1.1070.3.1.1.104.9.2.5	INTEGER	read-write	Decoder status subtitle priority: EBU First/DVB first
INT failMode	1.3.6.1.4.1.1070.3.1.1.104.9.2.6	INTEGER	read-write	Video Fail Mode,option:Black Screen=0,Still Picture=1,No Sync=2
INT dvbSubtitleLangEnable	1.3.6.1.4.1.1070.3.1.1.104.9.2.7	INTEGER	read-write	Decoder status DVB subtitle language enable: 0-off, 1-on
INT ebuSubtitleLangEnable	1.3.6.1.4.1.1070.3.1.1.104.9.2.8	INTEGER	read-write	Decoder status EBU subtitle language enable: 0-off, 1-on
INT closeCaption	1.3.6.1.4.1.1070.3.1.1.104.9.2.9	INTEGER	read-write	video close caption,option: 0-off, 1-on
INT videoOutAlarmEn	1.3.6.1.4.1.1070.3.1.1.104.9.2.10	INTEGER	read-write	Video Out Alarm On/Off Setting
INT vbiMode	1.3.6.1.4.1.1070.3.1.1.104.9.2.11	INTEGER	read-write	Video Output VBI Mode Setting
INT cvbsPAL	1.3.6.1.4.1.1070.3.1.1.104.9.2.12	INTEGER	read-write	video output CVBS PAL Setting, for example, PALBDGHI, PALN, PALN_C, SECAM
INT cvbsNTSC	1.3.6.1.4.1.1070.3.1.1.104.9.2.13	INTEGER	read-write	video output CVBS NTSC Setting, for example, NTSCM, NTSCM_J, NTSCM_443, PALM
STR videoOutputStatus	1.3.6.1.4.1.1070.3.1.1.104.9.2.14	DisplayString	read-only	show video output status
audioOutputEntry	1.3.6.1.4.1.1070.3.1.1.104.9.3
INT audioLevel	1.3.6.1.4.1.1070.3.1.1.104.9.3.1	INTEGER	read-write	Decoder status audio level: from 0 to 99
INT audioModulation	1.3.6.1.4.1.1070.3.1.1.104.9.3.2	INTEGER	read-write	Decoder status audio modulation: stereo/left/right/mono
STR audioLang	1.3.6.1.4.1.1070.3.1.1.104.9.3.3	DisplayString	read-write	Decoder status audio language 3 characters
INT audioOutAlarmEn	1.3.6.1.4.1.1070.3.1.1.104.9.3.4	INTEGER	read-write	Audio Out Alarm On/Off Setting
INT audioOutIndex	1.3.6.1.4.1.1070.3.1.1.104.9.3.5	INTEGER	read-write	specify which audio output
STR audioOutputStatus	1.3.6.1.4.1.1070.3.1.1.104.9.3.6	DisplayString	read-only	show audio output status
bissEntry	1.3.6.1.4.1.1070.3.1.1.104.9.4
INT bissMode	1.3.6.1.4.1.1070.3.1.1.104.9.4.1	INTEGER	read-write	biss mode, 0:biss 1, 1:biss E
STR biss1Key	1.3.6.1.4.1.1070.3.1.1.104.9.4.2	DisplayString	read-write	the key of biss 1
STR bissEKey	1.3.6.1.4.1.1070.3.1.1.104.9.4.3	DisplayString	read-write	the key of biss E
STR bissEId	1.3.6.1.4.1.1070.3.1.1.104.9.4.4	DisplayString	read-write	the id of biss E
INT bissSource	1.3.6.1.4.1.1070.3.1.1.104.9.4.5	INTEGER	read-write	the source of biss, it include ASI1TunerIP In(option)CIASI2Mux TS(option)
STR bissProgram	1.3.6.1.4.1.1070.3.1.1.104.9.4.6	DisplayString	read-write	the program number of descramble program according to biss,a program number occupy 2 bytes
decoderSelection	1.3.6.1.4.1.1070.3.1.1.104.9.5
INT decoderMode	1.3.6.1.4.1.1070.3.1.1.104.9.5.1	INTEGER	read-write	Decoder Mode Setting, it include manualauto
ethernetOutput	1.3.6.1.4.1.1070.3.1.1.104.10
IP ipAddress	1.3.6.1.4.1.1070.3.1.1.104.10.1	IpAddress	read-write	ethernet output ip address
INT streamUDPPort	1.3.6.1.4.1.1070.3.1.1.104.10.2	INTEGER	read-write	ethernet output stream UDP port
IP multicastIPAddress	1.3.6.1.4.1.1070.3.1.1.104.10.3	IpAddress	read-write	ethernet output multicast IP address
INT tsPacketPerUDP	1.3.6.1.4.1.1070.3.1.1.104.10.4	INTEGER	read-write	ethernet output TS packets per UDP
INT ttl	1.3.6.1.4.1.1070.3.1.1.104.10.5	INTEGER	read-write	ethernet output ttl
IP sourceNetmask	1.3.6.1.4.1.1070.3.1.1.104.10.6	IpAddress	read-write	External board netmask
IP sourceGateway	1.3.6.1.4.1.1070.3.1.1.104.10.7	IpAddress	read-write	External board gateway
STR sourceMac	1.3.6.1.4.1.1070.3.1.1.104.10.8	DisplayString	read-write	External board mac
INT multiUDPPort	1.3.6.1.4.1.1070.3.1.1.104.10.9	INTEGER	read-write	Multicast port
INT protocol	1.3.6.1.4.1.1070.3.1.1.104.10.10	INTEGER	read-write	0 udp; 1 trp;
INT typeService	1.3.6.1.4.1.1070.3.1.1.104.10.11	INTEGER	read-write	5 type: 0 normal; 1 min delay; 2 max throughput; 3 max reliability; 4 min monetary cost
INT source	1.3.6.1.4.1.1070.3.1.1.104.10.12	INTEGER	read-write	4 types: 0 asi; 1 tuner; 2 ds3; 3 CI
INT mode	1.3.6.1.4.1.1070.3.1.1.104.10.13	INTEGER	read-write	mode:DVB, IPTV
INT maxChannel	1.3.6.1.4.1.1070.3.1.1.104.10.14	INTEGER	read-only	when mode is IPTV, hardware sustain max channel
INT curMaxChannel	1.3.6.1.4.1.1070.3.1.1.104.10.15	INTEGER	read-write	when mode is IPTV, device can output channel number most currently
INT channelInput	1.3.6.1.4.1.1070.3.1.1.104.10.16	INTEGER	read-write	when mode is IPTV, input channel number currently
STR multicastValues	1.3.6.1.4.1.1070.3.1.1.104.10.17	DisplayString	read-write	when mode is IPTV, the value of multicast
STR gatewayMac	1.3.6.1.4.1.1070.3.1.1.104.10.18	DisplayString	read-write	the gatewat mac address, example: 44:45:53:54:00:00
STR highTargetMac	1.3.6.1.4.1.1070.3.1.1.104.10.19	DisplayString	read-write	when mode is IPTV, it denote all multicast channel's target mac, only save high 32bit, one channel occupy 4 bytes
STR lowTargetMac	1.3.6.1.4.1.1070.3.1.1.104.10.20	DisplayString	read-write	when mode is IPTV, it denote all multicast channel's target mac, only save target mac's low 16bit, one channel occupy 4 bytes, latter 2 bytes is effective
STR targetMac4Dvb	1.3.6.1.4.1.1070.3.1.1.104.10.21	DisplayString	read-write	when mode is DVB, the target mac address, example: 44:45:53:54:00:00
INT switch4Dvb	1.3.6.1.4.1.1070.3.1.1.104.10.23	INTEGER	read-write	switch control for IP Output of DVB mode
ciOutput	1.3.6.1.4.1.1070.3.1.1.104.11
INT ciSource	1.3.6.1.4.1.1070.3.1.1.104.11.1	INTEGER	read-write	CI output source
INT ciCount1	1.3.6.1.4.1.1070.3.1.1.104.11.2	INTEGER	read-write	CI1 output program counts
STR ciProgramNumber1	1.3.6.1.4.1.1070.3.1.1.104.11.3	DisplayString	read-write	CI1 output program numbers,it is a array
INT ciCount2	1.3.6.1.4.1.1070.3.1.1.104.11.4	INTEGER	read-write	CI2 output program counts
STR ciProgramNumber2	1.3.6.1.4.1.1070.3.1.1.104.11.5	DisplayString	read-write	CI2 output program numbers,it is a array
INT ciLock	1.3.6.1.4.1.1070.3.1.1.104.11.6	INTEGER	read-only	CI Lock? yes: 1,no: 0
STR ciMenuNode	1.3.6.1.4.1.1070.3.1.1.104.11.7	DisplayString	read-write	which node in ci menu
STR ciMenuNodeInfo	1.3.6.1.4.1.1070.3.1.1.104.11.8	DisplayString	read-write	the node values in ci menu
STR ciSlot1Status	1.3.6.1.4.1.1070.3.1.1.104.11.9	DisplayString	read-only	the status of slot1,if slot1 has card,then return the name of card,else return string whose length is zero-length
STR ciSlot2Status	1.3.6.1.4.1.1070.3.1.1.104.11.10	DisplayString	read-only	the status of slot2,if slot2 has card,then return the name of card,else return string whose length is zero-length
outputStatus	1.3.6.1.4.1.1070.3.1.1.104.12
asiOutputStatusEntry	1.3.6.1.4.1.1070.3.1.1.104.12.1
STR asiStatus	1.3.6.1.4.1.1070.3.1.1.104.12.1.1	DisplayString	read-only	ASI status
sdiOutputStatusEntry	1.3.6.1.4.1.1070.3.1.1.104.12.2
STR sdiStatus	1.3.6.1.4.1.1070.3.1.1.104.12.2.1	DisplayString	read-only	SDI status
ds3OutputStatusEntry	1.3.6.1.4.1.1070.3.1.1.104.12.3
STR ds3Status	1.3.6.1.4.1.1070.3.1.1.104.12.3.1	DisplayString	read-only	DS3 status
decoderOutputStatusEntry	1.3.6.1.4.1.1070.3.1.1.104.12.4
ethernetOutputStatusEntry	1.3.6.1.4.1.1070.3.1.1.104.12.5
STR ethernetStatus	1.3.6.1.4.1.1070.3.1.1.104.12.5.1	DisplayString	read-only	Ethernet status
ciOutputStatusEntry	1.3.6.1.4.1.1070.3.1.1.104.12.6
STR ciStatus	1.3.6.1.4.1.1070.3.1.1.104.12.6.1	DisplayString	read-only	CI status
ethernetInput	1.3.6.1.4.1.1070.3.1.1.104.13
IP streamIPAddress	1.3.6.1.4.1.1070.3.1.1.104.13.1	IpAddress	read-write	ethernet input ip address
IP streamNetmask	1.3.6.1.4.1.1070.3.1.1.104.13.2	IpAddress	read-write	External board Input netmask
IP streamGateway	1.3.6.1.4.1.1070.3.1.1.104.13.3	IpAddress	read-write	External board Input gateway
STR streamMacAddress	1.3.6.1.4.1.1070.3.1.1.104.13.4	DisplayString	read-only	External board Input mac
IP inputMulticastIPAddress	1.3.6.1.4.1.1070.3.1.1.104.13.5	IpAddress	read-write	ethernet input multicast IP address
INT multicastUDPPort	1.3.6.1.4.1.1070.3.1.1.104.13.6	INTEGER	read-write	Multicast port:0~65535
INT inputProtocol	1.3.6.1.4.1.1070.3.1.1.104.13.7	INTEGER	read-write	0 udp; 1 trp;
INT outputSmoothing	1.3.6.1.4.1.1070.3.1.1.104.13.8	INTEGER	read-write	0:Auto, 1:Fixed Rate, 2:Disable
INT tsBitRate	1.3.6.1.4.1.1070.3.1.1.104.13.9	INTEGER	read-write	input TS BitRate,from 0M~99M
s2Input	1.3.6.1.4.1.1070.3.1.1.104.14
INT s2LnbFrequency	1.3.6.1.4.1.1070.3.1.1.104.14.1	INTEGER	read-write	LNB frequency
INT s2SatFrequency	1.3.6.1.4.1.1070.3.1.1.104.14.2	INTEGER	read-write	Tuner frequency or centre_frequency for the transmission expressed in MHz, its value range: from 950MHz to 2150 MHz
INT s2SymbolRate	1.3.6.1.4.1.1070.3.1.1.104.14.3	INTEGER	read-write	Tuner symbol rate in symbols per second,its value range: from 0kb/s to 45000kb/s
INT s2LnbVoltage	1.3.6.1.4.1.1070.3.1.1.104.14.4	INTEGER	read-write	Tuner power, Option: 0v,13v,18v
INT s2Lnb22KHz	1.3.6.1.4.1.1070.3.1.1.104.14.5	INTEGER	read-write	Tuner 22 KHz, option: off or on
INT demodulatorMode	1.3.6.1.4.1.1070.3.1.1.104.14.6	INTEGER	read-write	DVB_S2 demodulator mode, option: DVB-SDVB-S2, parameter: 0,1
INT operationMode	1.3.6.1.4.1.1070.3.1.1.104.14.7	INTEGER	read-write	RX operation mode, option: QPSK 1/2QPSK 2/3QPSK 3/4QPSK 3/5QPSK 4/5QPSK 5/6QPSK 8/9QPSK 9/108PSK 2/38PSK 3/48PSK 3/58PSK 5/68PSK 8/98PSK 9/10, parameter: 012345678910111213
INT pilot	1.3.6.1.4.1.1070.3.1.1.104.14.8	INTEGER	read-write	pilot OPT, option: offon, parameter: 0, 1
INT roll_OffFactor	1.3.6.1.4.1.1070.3.1.1.104.14.9	INTEGER	read-write	Roll off OPT, option: 0.20.250.35, parameter: 0, 1, 2
functionAdd	1.3.6.1.4.1.1070.3.1.1.104.15
INT functionSelect	1.3.6.1.4.1.1070.3.1.1.104.15.1	INTEGER	read-write	function select,option:0:null;1:filter;2:multiplexer
filterSetup	1.3.6.1.4.1.1070.3.1.1.104.16
INT filterChannel	1.3.6.1.4.1.1070.3.1.1.104.16.1	INTEGER	read-write	filter channel,option:0:ASI;1:Tuner;2:IP In;3:CI
STR filterSection	1.3.6.1.4.1.1070.3.1.1.104.16.2	DisplayString	read-write	set filter section to Agent,format:old program number,old program number...,every parameter size is 2Byte
INT filterFunctionControl	1.3.6.1.4.1.1070.3.1.1.104.16.3	INTEGER	read-write	set filter function control,off:0;on:1
INT filterOutBitRate	1.3.6.1.4.1.1070.3.1.1.104.16.4	INTEGER	read-write	set out bitRate, range: from 0~150000Kbps
multiplexSetup	1.3.6.1.4.1.1070.3.1.1.104.17
STR programNumberContrast	1.3.6.1.4.1.1070.3.1.1.104.17.1	DisplayString	read-write	set program number contrast to Agent,format:channel,old program number,new program number,channel,old program number,new program number...,every parameter size is 2Byte
STR pidContrast	1.3.6.1.4.1.1070.3.1.1.104.17.2	DisplayString	read-write	set All PID contrast to Agent,format:channel,old PMT PID,new PMT PID,channel,old PCR PID,new PCR PID...,every parameter size is 2Byte
STR catSection	1.3.6.1.4.1.1070.3.1.1.104.17.3	DisplayString	read-write	set new CAT section to Agent,The transport stream Relating to the CAT seciton, reference ISO/IEC 13818-1
STR sdtSection	1.3.6.1.4.1.1070.3.1.1.104.17.4	DisplayString	read-write	set new SDT section to Agent,The transport stream Relating to the SDT seciton, reference DVB 300-468
STR pmtSection	1.3.6.1.4.1.1070.3.1.1.104.17.5	DisplayString	read-write	set new PMT section to Agent,The transport stream Relating to the PMT seciton, reference ISO/IEC 13818-1
STR nitActualSection	1.3.6.1.4.1.1070.3.1.1.104.17.6	DisplayString	read-write	Relating to the Actual section, its table ID is 0x40 in NIT,reference DVB 300-468
INT mxApply	1.3.6.1.4.1.1070.3.1.1.104.17.7	INTEGER	read-write	Send multiplexing command: send 1 to multiplexing
INT mxFunctionControl	1.3.6.1.4.1.1070.3.1.1.104.17.8	INTEGER	read-write	set mux function control,off:0;on:1
INT multiplexOutBitRate	1.3.6.1.4.1.1070.3.1.1.104.17.9	INTEGER	read-write	set out bitRate,range:from 0~150000Kbps
INT outTSID	1.3.6.1.4.1.1070.3.1.1.104.17.10	INTEGER	read-write	set out TS ID,range:from 0~65535
STR ghostSection	1.3.6.1.4.1.1070.3.1.1.104.17.11	DisplayString	read-write	set Ghost section to Agent,The transport stream Relating to the Ghost seciton, reference ISO/IEC 13818-1
INT originalNetworkId	1.3.6.1.4.1.1070.3.1.1.104.17.12	INTEGER	read-write	set Original Network ID,range:from 0~65535
INT muxOverFlowPercent	1.3.6.1.4.1.1070.3.1.1.104.17.13	INTEGER	read-write	mux overflow percent, range =(0-100).
ds3Input	1.3.6.1.4.1.1070.3.1.1.104.18
INT ds3InputType	1.3.6.1.4.1.1070.3.1.1.104.18.1	INTEGER	read-write	set DS3 Input Type, 0:Deinterleave; 1:Normal
cmOutput	1.3.6.1.4.1.1070.3.1.1.104.20
INT qamOrder	1.3.6.1.4.1.1070.3.1.1.104.20.1	INTEGER	read-write	QAM modulate mode,option:QPSK16QAM64QAM
INT bandWidths	1.3.6.1.4.1.1070.3.1.1.104.20.2	INTEGER	read-write	band width,option:6M7M8M
INT fec	1.3.6.1.4.1.1070.3.1.1.104.20.3	INTEGER	read-write	forward error correction,option: 1/2, 2/3, 3/4, 5/6, 7/8
INT guardInterval	1.3.6.1.4.1.1070.3.1.1.104.20.4	INTEGER	read-write	guard interval,option: 1/32,1/16,1/8,1/4
INT modulation	1.3.6.1.4.1.1070.3.1.1.104.20.5	INTEGER	read-write	carrier modulate,option: off,on
INT rfFrequency	1.3.6.1.4.1.1070.3.1.1.104.20.6	INTEGER	read-write	RF Frequency,from 48MHz~865MHz
INT spec	1.3.6.1.4.1.1070.3.1.1.104.20.7	INTEGER	read-write	spectrum inversion,option: normal,invert
INT attenuation	1.3.6.1.4.1.1070.3.1.1.104.20.8	INTEGER	read-write	RF attenuation,from 0db~18db
INT cmSource	1.3.6.1.4.1.1070.3.1.1.104.20.9	INTEGER	read-write	the source of cm output, 0:ASI, 1:Tuner, 2:IP In, 3:CI, 4:Mux TS
INT cmOutStatus	1.3.6.1.4.1.1070.3.1.1.104.20.10	INTEGER	read-only	the status of cm output, 0:normal, 1:overflow, 2:no sync
backupSetting	1.3.6.1.4.1.1070.3.1.1.104.21
INT backupEnable	1.3.6.1.4.1.1070.3.1.1.104.21.1	INTEGER	read-only	backup function switch
INT mainInputSource	1.3.6.1.4.1.1070.3.1.1.104.21.2	INTEGER	read-write	specify main input source
INT backupInputSource	1.3.6.1.4.1.1070.3.1.1.104.21.3	INTEGER	read-write	specify backup input source
INT tsIDPreference	1.3.6.1.4.1.1070.3.1.1.104.21.4	INTEGER	read-write	specify the TS ID of IP Input
INT bitRate	1.3.6.1.4.1.1070.3.1.1.104.21.5	INTEGER	read-write	specify the bit rate's range of IP Input
ntpSetting	1.3.6.1.4.1.1070.3.1.1.104.22
INT enable	1.3.6.1.4.1.1070.3.1.1.104.22.1	INTEGER	read-only	NTP setting function switch
IP serverIp	1.3.6.1.4.1.1070.3.1.1.104.22.2	IpAddress	read-write	specify the IP address of server
INT intervalTime	1.3.6.1.4.1.1070.3.1.1.104.22.3	INTEGER	read-write	specify the interval for synchronization time with server
INT timeZone	1.3.6.1.4.1.1070.3.1.1.104.22.4	INTEGER	read-write	specify the time zone for synchronization time with server
gigabitIPInfo	1.3.6.1.4.1.1070.3.1.1.104.23
STR localSetting	1.3.6.1.4.1.1070.3.1.1.104.23.1	DisplayString	read-write	local gigabit IP board setting
STR tsToIPSetting	1.3.6.1.4.1.1070.3.1.1.104.23.2	DisplayString	read-write	TS To IP parameter setting
STR ipToTSSetting	1.3.6.1.4.1.1070.3.1.1.104.23.3	DisplayString	read-write	IP To TS parameter setting
INT settingCommand	1.3.6.1.4.1.1070.3.1.1.104.23.4	INTEGER	write-only	the command for gigabit IP board setting, 0x1111
STR localStatus	1.3.6.1.4.1.1070.3.1.1.104.23.5	DisplayString	read-only	the status for local gigabit IP board
STR tsToIPStatus	1.3.6.1.4.1.1070.3.1.1.104.23.6	DisplayString	read-only	the status for TS To IP
STR ipToTSStatus	1.3.6.1.4.1.1070.3.1.1.104.23.7	DisplayString	read-only	the status for IP To TS

RFC description

Manages private configuration parameters for PBI 4000P and 5000P video tuner and output devices.

Start monitoring PBI 4000P/5000P broadcast IRD/decoder appliance with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download PBI-4000P-5000P-MIB