NQA-MIB

All MIBs › NQA-MIB

Organization: Huawei Technologies Co., Ltd.

Last Updated: 2006-01-09

Category: IP SLA and Network Quality

Description: Handles test instances and scheduling for Huawei's Network Quality Analyzer, storing performance results equivalent to IP SLA.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is NQA-MIB?

NQA-MIB is a Huawei MIB implementing Network Quality Analysis, Huawei's equivalent of Cisco's IP SLA, used to configure and run active network performance test probes on Huawei routers and switches. It exposes administrative parameters for various test types (including LSP/MPLS ping tests, traceroute-style "mtracert" multicast trace tests, and PPPoE session establishment tests), along with statistics tables recording test results such as completion counts, current phase, and error messages. This MIB is a monitoring-focused module by design: it lets operators actively probe network and service quality and then poll the resulting statistics to detect failures, timeouts, or slow negotiation phases, functioning much like a synthetic-transaction health check. It parallels the concepts of the IETF DISMAN-PING/TRACEROUTE MIBs and Cisco's proprietary IP SLA MIBs, though it is a distinct Huawei implementation with an overlapping but broader test-type scope. It is typically deployed in Huawei carrier and enterprise network infrastructure where active testing of MPLS paths, multicast trees, or PPPoE broadband service quality is required for SLA verification. Engineers can download the NQA-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in NQA-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei router/switch

Monitoring Examples

An operator would configure nqaAdminParaLspAddressType and nqaAdminParaLspNextHopAddress to set up an LSP ping test toward a specific MPLS next hop, then poll the corresponding statistics to check reachability. For multicast path diagnostics, nqaMtracertStatsIndex and nqaMtracertStatsAddressType identify a trace test instance and its target address family. For broadband service testing, nqaPppoeStatsIndex and nqaPppoeRedialIndex track individual PPPoE test attempts, while nqaPppoeStatsCompletions, nqaPppoeStatsCurrentPhase, and nqaPppoeStatsErrorMessage reveal whether a PPPoE session test completed successfully or stalled at a specific phase, with nqaPppoeDiscoveryTimeout and nqaPppoeLcpTimeout defining the thresholds used to flag a stall.

What Can Be Monitored

LSP/MPLS ping test results
multicast traceroute (mtracert) statistics
PPPoE session test completions
PPPoE session current phase/error message
PPPoE discovery/LCP timeout thresholds

Imported Objects

From HUAWEI-ETHOAM-MIB

HWDot1agCfmEgressActionFieldValue
HWDot1agCfmIngressActionFieldValue
HWDot1agCfmRelayActionFieldValue

From HUAWEI-MIB

hwDatacomm

OBJECT-IDENTITY

From IEEE802171-CFM-MIB

Dot1agCfmMaintAssocName
Dot1agCfmMaintDomainName
Dot1agCfmMepIdOrZero

From IF-MIB

InterfaceIndexOrZero

From INET-ADDRESS-MIB

InetAddress
InetAddressType
InetPortNumber

From P-BRIDGE-MIB

EnabledStatus

From Q-BRIDGE-MIB

VlanIdOrNone

From RFC1155-SMI

IpAddress

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-GROUP
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32
mib-2

From SNMPv2-TC

DateAndTime
DisplayString
MacAddress
RowStatus
StorageType
TEXTUAL-CONVENTION
TimeInterval
TimeStamp
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
nqa	1.3.6.1.4.1.2011.5.25.111			HUAWEI service quality detect funcion.
nqaBase	1.3.6.1.4.1.2011.5.25.111.1
STR nqaVersion	1.3.6.1.4.1.2011.5.25.111.1.1	DisplayString	read-only	The NQA version (for example, 1.1). It can be used for version management.
ENA nqaEnable	1.3.6.1.4.1.2011.5.25.111.1.2	EnableValue	read-write	Indicates the switch of enabling NQA client. (The value range: enable:1; disable:2.The default value is enable(1))
ENA nqaReset	1.3.6.1.4.1.2011.5.25.111.1.3	EnableValue	read-write	Clears all the enabled test configurations. (The value range: enable:1; disable:2. The default value is disable(2))
DAT nqaTimeOfLastSetError	1.3.6.1.4.1.2011.5.25.111.1.4	DateAndTime	read-only	The time of the last configuration error. (0 indicates that the configuration does not fail).
STR nqaLastSetError	1.3.6.1.4.1.2011.5.25.111.1.5	DisplayString	read-only	The time of the last configuration error. (0 indicates that the configuration does not fail).
I32 nqaNumOfCurrentCtrlEntry	1.3.6.1.4.1.2011.5.25.111.1.6	Integer32	read-write	The total number of current configuration tests.
U32 nqaMaxConcurrentRequests	1.3.6.1.4.1.2011.5.25.111.1.7	Unsigned32	read-write	The maximum number of concurrent active requests that are allowed within an agent implementation.
U32 nqaMaxNumOfRequests	1.3.6.1.4.1.2011.5.25.111.1.8	Unsigned32	read-only	The maximum number of requests that are allowed within an agent implementation.
I32 nqaJitterVersion	1.3.6.1.4.1.2011.5.25.111.1.9	Integer32	read-write	Selects the version of jitter test. (The value range: old version:1, new version:2. The default value is old version(1))
BIT nqaSupportTestType	1.3.6.1.4.1.2011.5.25.111.1.10	Bits	read-only	Test type that the current device supports. Data structure of the type is in the format of bits. Each bit represents a test type. The mappings between bits and tests are as follows: icmp(0), tcp(1), udp(2), http(3), ftp(4), jitter(5), snmp(6), trace(7), lspPing(8), lspTrace(9), dns(10), dhcp(11), dlsw(12), pwe3Ping(13), pwe3Trace(14), mPing(15), mTrace(16), macPing(17), macTunnelPing(18), lspJitter(19), icmpJitter(20), pathJitter(21), pathMtu(22), pppoe(23), vplsmPing(24), vplsmacPing(25), vplsmacTrace(26), vplsMTrace(27), gmacping(28), gmactrace(29), mactrace(30), vplspwping(31), vplspwtrace(32) The value #0x00 indicates don't suppourt all testtypes.
BIT nqaSupportServerType	1.3.6.1.4.1.2011.5.25.111.1.11	Bits	read-only	Test type that the current device supports. Data structure of the type is in the format of bits. Each bit represents a test type. tcpServer(0), udpServer(1), icmpServer(2) The value #0x00 indicates don't suppourt all servertypes.
nqaCtrl	1.3.6.1.4.1.2011.5.25.111.2
nqaAdminCtrlTable	1.3.6.1.4.1.2011.5.25.111.2.1		not-accessible	A table of NQA monitoring definitions.
nqaAdminCtrlEntry	1.3.6.1.4.1.2011.5.25.111.2.1.1		not-accessible	Defines an entry in the nqaAdminCtrlTable.
STR nqaAdminCtrlOwnerIndex	1.3.6.1.4.1.2011.5.25.111.2.1.1.1	SnmpAdminString	not-accessible	To facilitate the provisioning of access control by a security administrator using the View-Based Access Control Model for tables in which multiple users may need to independently create or modify entries, the initial index is used as an 'ownerindex'. When used in conjunction with such a security policy all entries in the table belonging to a particular user (or group) will have the same value for this initial index. For a given user's entries in a particular table, the object identifiers for the information in these entries will have the same subidentifiers (except for the 'column' subidentifier) up to the end of the encoded owner index.
STR nqaAdminCtrlTestName	1.3.6.1.4.1.2011.5.25.111.2.1.1.2	SnmpAdminString	not-accessible	The name of a test. This is locally unique, within the scope of an nqaAdminCtrlOwnerIndex.
STR nqaAdminCtrlTag	1.3.6.1.4.1.2011.5.25.111.2.1.1.3	DisplayString	read-create	A string which is the description of the test instance.
NQA nqaAdminCtrlType	1.3.6.1.4.1.2011.5.25.111.2.1.1.4	NqaType	read-create	The type of the test instance.
I32 nqaAdminCtrlFrequency	1.3.6.1.4.1.2011.5.25.111.2.1.1.5	Integer32	read-create	Specifies the interval when the test instance repeats.
I32 nqaAdminCtrlTimeOut	1.3.6.1.4.1.2011.5.25.111.2.1.1.6	Integer32	read-create	Specifies the duration to wait for the completion of test instance. The default value of DHCP-type and FTP-type test instance is 15s, The default value of PPPoE-type test instance is 30s, and that of other types is 3s.
I32 nqaAdminCtrlThreshold1	1.3.6.1.4.1.2011.5.25.111.2.1.1.7	Integer32	read-create	Represents the threshold of RTD (Round Trip Delay). If the RTT violates the threshold, the corresponding counter will increase. It applies to any type of test instance.
I32 nqaAdminCtrlThreshold2	1.3.6.1.4.1.2011.5.25.111.2.1.1.8	Integer32	read-create	Represents the threshold of OWD (One Way Delay) from source to destination. If the OWD violates the threshold, the corresponding counter will increase. It applies only to jitter-type test instances.
I32 nqaAdminCtrlThreshold3	1.3.6.1.4.1.2011.5.25.111.2.1.1.9	Integer32	read-create	Represents the threshold of OWD (One Way Delay) from destination to source. If the OWD violates the threshold, the corresponding counter will increase. It applies only to jitter-type test instances.
ROW nqaAdminCtrlStatus	1.3.6.1.4.1.2011.5.25.111.2.1.1.10	RowStatus	read-create	To set the value of this object can create or delete the specified test instance and the records belonging to it. Before deleting a test instance, the custom must make sure that the status of the test instance is inactive through nqaScheduleOperStatus. The value can be set to 'CreateAndGo (4)', 'Destroy (6)' and 'Active (1)'.
nqaAdminParaTable	1.3.6.1.4.1.2011.5.25.111.2.2		not-accessible	Set parameter for a test.
nqaAdminParaEntry	1.3.6.1.4.1.2011.5.25.111.2.2.1		not-accessible	set parameter in the nqaAdminParaTable.
IPt nqaAdminParaTargetAddressType	1.3.6.1.4.1.2011.5.25.111.2.2.1.1	InetAddressType	read-write	Represents the address type of destination.
IP nqaAdminParaTargetAddress	1.3.6.1.4.1.2011.5.25.111.2.2.1.2	InetAddress	read-write	Represents the address of destination.
INE nqaAdminParaTargetPort	1.3.6.1.4.1.2011.5.25.111.2.2.1.3	InetPortNumber	read-write	Represents the port number of destination.
IPt nqaAdminParaSourceAddressType	1.3.6.1.4.1.2011.5.25.111.2.2.1.4	InetAddressType	read-write	Represents the address type of source.
IP nqaAdminParaSourceAddress	1.3.6.1.4.1.2011.5.25.111.2.2.1.5	InetAddress	read-write	Represents the address of source.
INE nqaAdminParaSourcePort	1.3.6.1.4.1.2011.5.25.111.2.2.1.6	InetPortNumber	read-write	Represents the port number of source.
U32 nqaAdminParaMaxTtl	1.3.6.1.4.1.2011.5.25.111.2.2.1.7	Unsigned32	read-write	Specifies the maximum value of TTL. The value cannot be set to 0 unless the test-type is pwe3ping, the lsp-version is rfc4379, and the ttl-copymode is pipe.
U32 nqaAdminParaInitialTtl	1.3.6.1.4.1.2011.5.25.111.2.2.1.8	Unsigned32	read-write	Specifies the initial value of TTL.
STO nqaAdminParaStorageType	1.3.6.1.4.1.2011.5.25.111.2.2.1.9	StorageType	read-write	The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row.
U32 nqaAdminParaMaxFailures	1.3.6.1.4.1.2011.5.25.111.2.2.1.10	Unsigned32	read-write	The value of this object indicates the maximum number of consecutive timeouts allowed before terminating a remote traceroute request. A value of 255 (maximum hop count/possible TTL value) indicates that the function of terminating a remote traceroute request when a specific number of successive timeouts are detected is disabled.
T/F nqaAdminParaDontFragment	1.3.6.1.4.1.2011.5.25.111.2.2.1.11	TruthValue	read-write	This object enables setting of Don't Fragment (DF) flag in the IP header for a probe. Use of this object enables performing a manual PATH MTU test.
U32 nqaAdminParaDataSize	1.3.6.1.4.1.2011.5.25.111.2.2.1.12	Unsigned32	read-write	The size of data field in packet.
OCT nqaAdminParaDataFill	1.3.6.1.4.1.2011.5.25.111.2.2.1.13	OCTET STRING	read-write	Represents the characters used for filling the data field. This object is used together with the corresponding object, nqaAdminParaDataSize.
NUM nqaAdminParaIfIndex	1.3.6.1.4.1.2011.5.25.111.2.2.1.14	InterfaceIndexOrZero	read-write	Specified the source interface or tunnel, from which probes of the test instance are sent. The object applies to DHCP, jitter, icmpjitter, ICMP, lspping or lsptrace type test instance. The value zero implies that the object is disabled.
T/F nqaAdminParaByPassRouteTable	1.3.6.1.4.1.2011.5.25.111.2.2.1.15	TruthValue	read-write	The purpose of this object is to optionally enable bypassing the route table. If enabled, the remote host will bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly-attached network, an error is returned. This option can be used to perform the ping/traceroute operation to a local host through an interface that has no route defined (e.g., after the interface was dropped by routed).
STR nqaAdminParaMiscOptions	1.3.6.1.4.1.2011.5.25.111.2.2.1.16	SnmpAdminString	read-write	Enables an application to specify implementation dependent options.
U32 nqaAdminParaProbeCount	1.3.6.1.4.1.2011.5.25.111.2.2.1.17	Unsigned32	read-write	Specifies the number of packets sent by the test instance, or times of probe repeated, in which may send several packets. The second case applies to jitter-type test instances.
BIT nqaAdminParaTrapGeneration	1.3.6.1.4.1.2011.5.25.111.2.2.1.18	Bits	read-write	Switch of notification. Determine whether and how to send notifications for the test instance: - probeFailure(0) - Generate a PathChange notification when the current path varies from a previously determined path. - testFailure(1) - Generate a TestFailed notification when the full path to a target can't be determined. - testCompletion(2) - Generate a TestCompleted notification when the path to a target has been determined. - overRtdThreshold(3) - Generate a Overthreshold of RTD notification when the statistic results exceed threshold. - overOwdThresholdSd(4) - Generate a Overthreshold of OWD-SD notification when the statistic results exceed threshold. - overOwdThresholdDs(5) - Generate a Overthreshold of OWD-DS notification when the statistic results exceed threshold. The value #0x00 indicates disable all notifications.
U32 nqaAdminParaTrapProbeFailureFilter	1.3.6.1.4.1.2011.5.25.111.2.2.1.19	Unsigned32	read-write	Specifies the condition when to trigger an nqaProbeFailed notification. When the number of consecutive failed probes violates the threshold indicated by nqaAdminParaTrapProbeFailureFilter, a notification will be created. This object is used together with nqaAdminParaTrapGeneration.
U32 nqaAdminParaTrapTestFailureFilter	1.3.6.1.4.1.2011.5.25.111.2.2.1.20	Unsigned32	read-write	Specifies the condition when to trigger an nqaTestFailed notification. When the number of failed tests violates the threshold indicated by nqaAdminParaTrapTestFailureFilter, a notification will be created. There are usually several probes in each test. This object is used together with nqaAdminParaTrapGeneration.
I32 nqaAdminParaDSField	1.3.6.1.4.1.2011.5.25.111.2.2.1.21	Integer32	read-write	Specifies the Differentiated Services (DS) field in the IP packet. The DS field is defined as the Type Of Service (TOS) octet in IPv4 header or as the Traffic Class octet in IPv6 header.
IPt nqaAdminParaDnsServerAddressType	1.3.6.1.4.1.2011.5.25.111.2.2.1.22	InetAddressType	read-write	Specifies the address type of DNS server.
IP nqaAdminParaDnsServerAddress	1.3.6.1.4.1.2011.5.25.111.2.2.1.23	InetAddress	read-write	Specifies the address of DNS server.
NQA nqaAdminParaOperation	1.3.6.1.4.1.2011.5.25.111.2.2.1.24	NqaOperation	read-write	Specifies the operation of FTP or HTTP type test instance. The operations of FTP-type test instance include get and put. The operations of HTTP-type test instance include get and post.
STR nqaAdminParaHttpVersion	1.3.6.1.4.1.2011.5.25.111.2.2.1.25	DisplayString	read-write	Specifies the version of HTTP.
STR nqaAdminParaHttpOperationString	1.3.6.1.4.1.2011.5.25.111.2.2.1.26	DisplayString	read-write	A string that specifies the HTTP operation which will be sent to the HTTP server.
U32 nqaAdminParaTestFailurePercent	1.3.6.1.4.1.2011.5.25.111.2.2.1.27	Unsigned32	read-write	Specifies the scale over which the test will be regarded as failed.
STR nqaAdminParaFtpUserName	1.3.6.1.4.1.2011.5.25.111.2.2.1.28	DisplayString	read-write	Specifies the user name of the FTP server.
STR nqaAdminParaFtpPassword	1.3.6.1.4.1.2011.5.25.111.2.2.1.29	DisplayString	read-write	Specifies the password of the user of the FTP server.
STR nqaAdminParaFtpFilePath	1.3.6.1.4.1.2011.5.25.111.2.2.1.30	DisplayString	read-write	Specifies the full name of the file which will be transmitted by the FTP-type test instance.
I32 nqaAdminParaFtpFileSize	1.3.6.1.4.1.2011.5.25.111.2.2.1.31	Integer32	read-write	Specifies the size that the file will be transmitted by the FTP-type test instance. It may be part of the file.
I32 nqaAdminParaInterval	1.3.6.1.4.1.2011.5.25.111.2.2.1.32	Integer32	read-write	Specifies the interval between two consecutive probe packets.
I32 nqaAdminParaNumPackets	1.3.6.1.4.1.2011.5.25.111.2.2.1.33	Integer32	read-write	Specifies the number of packet sent in each probe. This object is used together with nqaAdminParaProbeCount, and only apples to jitter-type test instance.
STR nqaAdminParaVrfName	1.3.6.1.4.1.2011.5.25.111.2.2.1.34	DisplayString	read-write	Specifies the VRF name.
INT nqaAdminParaLspAddressType	1.3.6.1.4.1.2011.5.25.111.2.2.1.35	INTEGER	read-write	Specifies the address type of LSP. The object applies to lspping, lsptrace and lspjitter type test instance.
I32 nqaAdminParaLspAddressMask	1.3.6.1.4.1.2011.5.25.111.2.2.1.36	Integer32	read-write	Specifies the address mask of LSP. The object apples to lspping, lsptrace and lspjitter type test instance.
IP nqaAdminParaLspIpAddress	1.3.6.1.4.1.2011.5.25.111.2.2.1.37	InetAddress	read-write	IP Address filled in the ip header, must be a 127/8 address.
U32 nqaAdminParaLspPWE3VcId	1.3.6.1.4.1.2011.5.25.111.2.2.1.38	Unsigned32	read-write	The local Pseudo wire ID in PWE3 Ping test
INT nqaAdminParaLspPWE3Type	1.3.6.1.4.1.2011.5.25.111.2.2.1.39	INTEGER	read-write	The encapsulation type of Pseudo wire ID in the PWE3 Ping test
INT nqaAdminParaLspPWE3Option	1.3.6.1.4.1.2011.5.25.111.2.2.1.40	INTEGER	read-write	The label type of PWE3 Ping and PWE3 Tracert test.
U32 nqaAdminParaLspPWE3RemoteVcId	1.3.6.1.4.1.2011.5.25.111.2.2.1.41	Unsigned32	read-write	The remote Pseudo wire ID in PWE Ping test.
IP nqaAdminParaLspPWE3RemoteAddress	1.3.6.1.4.1.2011.5.25.111.2.2.1.42	InetAddress	read-write	The remote IP address in PWE3 Ping test.
U32 nqaAdminParaLspExp	1.3.6.1.4.1.2011.5.25.111.2.2.1.43	Unsigned32	read-write	The 3bit EXP field of the MPLS echo packet label.
INT nqaAdminParaLspReplyMode	1.3.6.1.4.1.2011.5.25.111.2.2.1.44	INTEGER	read-write	ReplyMode Value Meaning ----- ------- 1 Do not reply 2 Reply via an IPv4/IPv6 UDP packet 3 Reply via an IPv4/IPv6 UDP packet with Router Alert 4 Reply via application level control channel 5 Reply via a VPLS IPv4 UDP packet
I32 nqaAdminParaResultRowMax	1.3.6.1.4.1.2011.5.25.111.2.2.1.45	Integer32	read-write	Specifies the maximum number of result records.
I32 nqaAdminParaHistoryRowMax	1.3.6.1.4.1.2011.5.25.111.2.2.1.46	Integer32	read-write	Specifies the maximum number of history records.
ENA nqaAdminParaCreateHopsEntries	1.3.6.1.4.1.2011.5.25.111.2.2.1.47	EnableValue	read-write	When set to 'enable (1)', the result of each hop will be kept in nqaResultsTable. The object applies to trace, pwe3trace, lsptrace, mtrace type test instance.
INT nqaAdminParaLspVCType	1.3.6.1.4.1.2011.5.25.111.2.2.1.48	INTEGER	read-write	The type of protocol which establishes PW in the pwe3tracert test
IP nqaAdminParaMTraceLastHopAddress	1.3.6.1.4.1.2011.5.25.111.2.2.1.49	InetAddress	read-write	The last hop router's IP address in Mtrace test.
IP nqaAdminParaMTraceSourceAddress	1.3.6.1.4.1.2011.5.25.111.2.2.1.50	InetAddress	read-write	The IP address of the multicast source for the path being traced in Mtrace test.
IP nqaAdminParaMTraceGroupAddress	1.3.6.1.4.1.2011.5.25.111.2.2.1.51	InetAddress	read-write	The group address to be traced in Mtrace test, or zero if no group-specific information is desired.
U32 nqaAdminParaMTraceMaxTtl	1.3.6.1.4.1.2011.5.25.111.2.2.1.52	Unsigned32	read-write	The maximum number of hops that the requester wants to trace in Mtrace test.
INT nqaAdminParaMTraceSendMode	1.3.6.1.4.1.2011.5.25.111.2.2.1.53	INTEGER	read-write	The sending mode of the Query pamessage in Mtrace test.
U32 nqaAdminParaMTraceResponseTtl	1.3.6.1.4.1.2011.5.25.111.2.2.1.54	Unsigned32	read-write	The TTL at which to multicast the response in Mtrace test, if the response address is a multicast address.
IPt nqaAdminParaMTraceResponseAddressType	1.3.6.1.4.1.2011.5.25.111.2.2.1.55	InetAddressType	read-write	Mtrace response address type
IP nqaAdminParaMTraceResponseAddress	1.3.6.1.4.1.2011.5.25.111.2.2.1.56	InetAddress	read-write	This field specifies where the completed traceroute response packet gets sent in Mtrace test. It can be a unicast address or a multicast address
NQA nqaAdminParaDistanceNodeType	1.3.6.1.4.1.2011.5.25.111.2.2.1.57	NqaDistanceNodeType	read-write	The destination of MAC ping(mac address or rmepid).
MAC nqaAdminParaMacAddress	1.3.6.1.4.1.2011.5.25.111.2.2.1.58	MacAddress	read-write	Mac address of the destination of MAC PING.
DOT nqaAdminParaRMepID	1.3.6.1.4.1.2011.5.25.111.2.2.1.59	Dot1agCfmMepIdOrZero	read-write	Rmepid of the destination of MAC PING.
OCT nqaAdminParaMDName	1.3.6.1.4.1.2011.5.25.111.2.2.1.60	OCTET STRING	read-write	Indicate the MD name in which the MAC Ping operated.
OCT nqaAdminParaMAName	1.3.6.1.4.1.2011.5.25.111.2.2.1.61	OCTET STRING	read-write	Indicate the MA name in which the MAC Ping operated.
OCT nqaAdminParaMacTunnelName	1.3.6.1.4.1.2011.5.25.111.2.2.1.62	OCTET STRING	read-write	Indicate the MAC Tunnel name in which the MAC Ping operated.
I32 nqaAdminParaPathMtuStep	1.3.6.1.4.1.2011.5.25.111.2.2.1.63	Integer32	read-write	Specify the step of the path MTU test.If the last response was received successful,the next packet's length will add the step.
I32 nqaAdminParaPathMtuDiscoveryPathMtuMax	1.3.6.1.4.1.2011.5.25.111.2.2.1.64	Integer32	read-write	Specify the max value of the discovery field in the path MTU test.
INT nqaAdminParaIcmpJitterMode	1.3.6.1.4.1.2011.5.25.111.2.2.1.65	INTEGER	read-write	Select the type of ICMP packets to be sent in ICMP jitter and path jitter test.The value can be icmpTimestamp(1) or icmpEcho(2).
INT nqaAdminParaCodecType	1.3.6.1.4.1.2011.5.25.111.2.2.1.66	INTEGER	read-write	To indicate the codec type to be used with jitter probe. This is applicable only for the jitter probe.
I32 nqaAdminParaIcpifAdvFactor	1.3.6.1.4.1.2011.5.25.111.2.2.1.67	Integer32	read-write	The advantage factor depends on the type of access and how the service is to be used. This object will be used while calculating the ICPIF (Calculated Planning Impairment Factor) values. Suggestion values: \|---------------------------------------------------\|-------\| \| Service \|factor \| \|---------------------------------------------------\|-------\| \| conventional wire-line \| 0 \| \|---------------------------------------------------\|-------\| \| mobility within Building \| 5 \| \|---------------------------------------------------\|-------\| \| mobility within geographical area \| 10 \| \|---------------------------------------------------\|-------\| \| access to hard-to-reach location \| 20 \| \|---------------------------------------------------\|-------\|
INT nqaAdminParaFtpMode	1.3.6.1.4.1.2011.5.25.111.2.2.1.68	INTEGER	read-write	To indicate the mode to be used with ftp probe. This is applicable only for the ftp probe.
ENA nqaAdminParaHardwareBased	1.3.6.1.4.1.2011.5.25.111.2.2.1.69	EnabledStatus	read-write	Indicates that the hardware is enabled to send packets. (The value range: enable:1;disable:2.The default value is disable(2))
OCT nqaAdminParaPppoeUserName	1.3.6.1.4.1.2011.5.25.111.2.2.1.70	OCTET STRING	read-write	Specifies the username of PPPoE dial-up. For jitter,icmp,traceroute, tcp,udp,ftp,dns,http probes, this parameter indicates that the probe uses PPPoE encapsulation. This parameter accepts the characters in sight only.
OCT nqaAdminParaPppoePassword	1.3.6.1.4.1.2011.5.25.111.2.2.1.71	OCTET STRING	read-write	Specifies the password of PPPoE dial-up. This is applicable only for the PPPoE probe. This parameter accepts the characters in sight only.
I32 nqaAdminParaPppoeVlanIf	1.3.6.1.4.1.2011.5.25.111.2.2.1.72	Integer32	read-write	Specifies the vlanif of PPPoE dial-up. For jitter, icmp, traceroute, tcp, udp, ftp, dns, http probes, this parameter indicates that the probe uses PPPoE encapsulation.
INT nqaAdminParaPppoeAuthenticationMode	1.3.6.1.4.1.2011.5.25.111.2.2.1.73	INTEGER	read-write	Specifies the authentication mode of PPPoE dial-up. This is applicable only for the PPPoE probe.
I32 nqaAdminParaPppoeRedialUpTimes	1.3.6.1.4.1.2011.5.25.111.2.2.1.74	Integer32	read-write	Specifies the redialup times of PPPoE dial-up. This is applicable only for the PPPoE probe.
I32 nqaAdminParaPppoeInterval	1.3.6.1.4.1.2011.5.25.111.2.2.1.75	Integer32	read-write	Specifies the redialup interval of PPPoE dial-up. This is applicable only for the PPPoE probe.
OCT nqaAdminParaVsiName	1.3.6.1.4.1.2011.5.25.111.2.2.1.76	OCTET STRING	read-write	Specify the name of the VSI(Virtual Switch Instance)
VLA nqaAdminParaVlanId	1.3.6.1.4.1.2011.5.25.111.2.2.1.77	VlanIdOrNone	read-write	Specify the Vlan ID
INT nqaAdminParaLspTunnelType	1.3.6.1.4.1.2011.5.25.111.2.2.1.78	INTEGER	read-write	To indicate ping/trace which lsp tunnel.
IP nqaAdminParaLspNextHopAddress	1.3.6.1.4.1.2011.5.25.111.2.2.1.79	InetAddress	read-write	Represents the address of nexthop.
INT nqaAdminParaLspVersion	1.3.6.1.4.1.2011.5.25.111.2.2.1.80	INTEGER	read-write	Specify lsp version of protocol. Draft-ietf-mpls-lsp-ping-06 protocol, RFC4379 protocol or ptn mode.
IPt nqaAdminParaRemoteAddressType	1.3.6.1.4.1.2011.5.25.111.2.2.1.81	InetAddressType	read-write	Represents the address type of remote.
IP nqaAdminParaRemoteAddress	1.3.6.1.4.1.2011.5.25.111.2.2.1.82	InetAddress	read-write	Represents the address of remote.
INT nqaAdminParaTimeUnit	1.3.6.1.4.1.2011.5.25.111.2.2.1.83	INTEGER	read-write	The unit of the timestamp, ms or us.
nqaScheduleTable	1.3.6.1.4.1.2011.5.25.111.2.3		not-accessible	Schedule test .
nqaScheduleEntry	1.3.6.1.4.1.2011.5.25.111.2.3.1		not-accessible	Set start-up in the nqaAdminParaTable.
INT nqaScheduleStartType	1.3.6.1.4.1.2011.5.25.111.2.3.1.1	INTEGER	read-write	Specifies the start type of the test instance. The object is used together with nqaScheduleStartTime.
U32 nqaScheduleStartTime	1.3.6.1.4.1.2011.5.25.111.2.3.1.2	Unsigned32	read-write	Specifies the start time of the test instance. Setting the value to 0 indicates to start the test instance immediately. After configuring this object, the status of the test instance is active, and the parameters of the test instance can't be changed.
INT nqaScheduleEndType	1.3.6.1.4.1.2011.5.25.111.2.3.1.3	INTEGER	read-write	Specifies the end type of the test instance. The object is used together with nqaScheduleEndTime.
U32 nqaScheduleEndTime	1.3.6.1.4.1.2011.5.25.111.2.3.1.4	Unsigned32	read-write	Specifies the end time of the test instance.
I32 nqaScheduleAgeTime	1.3.6.1.4.1.2011.5.25.111.2.3.1.5	Integer32	read-write	Specifies the aging time of the test instance, the time how long the test instance will be reserved in NQA, after the test instance is inactive. Setting the value to 0 indicates reserving the test instance eternally.
NUM nqaScheduleElapsedTime	1.3.6.1.4.1.2011.5.25.111.2.3.1.6	TimeInterval	read-only	The elapsed time (the period of time after task dispatch).
I32 nqaScheduleNumOfInitiations	1.3.6.1.4.1.2011.5.25.111.2.3.1.7	Integer32	read-only	Specifies the times that the test instance has been initialed. This object is used as the index of the result table, HTTP statistics table, jitter statistics table, FTP statistics table and history table.
I32 nqaScheduleLastFinishIndex	1.3.6.1.4.1.2011.5.25.111.2.3.1.8	Integer32	read-only	Specifies the latest finished test of the test instance, which is used as the index of the result table.
INT nqaScheduleOperStatus	1.3.6.1.4.1.2011.5.25.111.2.3.1.9	INTEGER	read-write	Specifies the status of dispatching operation: - reset: Clear all the records of the test instance. - stop: Stop the test instance, if it's running. - restart: Stop the test instance, if it's running, and restart the test instance immediately. - active: The test instance is running; the parameters of the test instances can't be changed. - inactive: The test instance doesn't be scheduled; the parameters of the test instances can be changed.
I32 nqaScheduleLastCollectIndex	1.3.6.1.4.1.2011.5.25.111.2.3.1.10	Integer32	read-only	Specifies the index of the latest collection statistics result record in the collection result table.
nqaGroupTable	1.3.6.1.4.1.2011.5.25.111.2.4		not-accessible	Set group for a test.
nqaGroupEntry	1.3.6.1.4.1.2011.5.25.111.2.4.1		not-accessible	Set parameters in the nqaGroupTable.
INT nqaGroupStatusType	1.3.6.1.4.1.2011.5.25.111.2.4.1.1	INTEGER	read-write	Specifies the group status of the test instance. The value can be normal (1), leader (2) or member (3).
I32 nqaGroupPeriod	1.3.6.1.4.1.2011.5.25.111.2.4.1.2	Integer32	read-write	Specifies the interval during which all members in the specified group will be executed.
STR nqaGroupLeaderOwnerIndex	1.3.6.1.4.1.2011.5.25.111.2.4.1.3	SnmpAdminString	read-write	Specifies the owner index of the group leader, if the test instance is a member of the group.
STR nqaGroupLeaderTestName	1.3.6.1.4.1.2011.5.25.111.2.4.1.4	SnmpAdminString	read-write	Specifies the test name of the group leader, if the test instance is a member of the group.
I32 nqaGroupMemberNum	1.3.6.1.4.1.2011.5.25.111.2.4.1.5	Integer32	read-only	Specifies the number of member in the group.
ENA nqaGroupMemberFree	1.3.6.1.4.1.2011.5.25.111.2.4.1.6	EnableValue	read-write	Free all members in the group.
nqaAdminParaExtTable	1.3.6.1.4.1.2011.5.25.111.2.5		not-accessible	Set parameter for a test.
nqaAdminParaExtEntry	1.3.6.1.4.1.2011.5.25.111.2.5.1		not-accessible	Set parameter in the nqaAdminParaExtTable.
OCT nqaAdminExtPara1	1.3.6.1.4.1.2011.5.25.111.2.5.1.1	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara2 object. The value is automatically assigned by the system after the type of the test case is ascertained.
I32 nqaAdminExtPara2	1.3.6.1.4.1.2011.5.25.111.2.5.1.2	Integer32	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara1 object after the test case is ascertained.
OCT nqaAdminExtPara3	1.3.6.1.4.1.2011.5.25.111.2.5.1.3	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara4 object. The value is automatically assigned by the system after the type of the test case is ascertained.
I32 nqaAdminExtPara4	1.3.6.1.4.1.2011.5.25.111.2.5.1.4	Integer32	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara3 object after the test case is ascertained.
OCT nqaAdminExtPara5	1.3.6.1.4.1.2011.5.25.111.2.5.1.5	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara6 object. The value is automatically assigned by the system after the type of the test case is ascertained.
I32 nqaAdminExtPara6	1.3.6.1.4.1.2011.5.25.111.2.5.1.6	Integer32	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara5 object after the test case is ascertained.
OCT nqaAdminExtPara7	1.3.6.1.4.1.2011.5.25.111.2.5.1.7	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara8 object. The value is automatically assigned by the system after the type of the test case is ascertained.
I32 nqaAdminExtPara8	1.3.6.1.4.1.2011.5.25.111.2.5.1.8	Integer32	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara7 object after the test case is ascertained.
OCT nqaAdminExtPara9	1.3.6.1.4.1.2011.5.25.111.2.5.1.9	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara10 object. The value is automatically assigned by the system after the type of the test case is ascertained.
I32 nqaAdminExtPara10	1.3.6.1.4.1.2011.5.25.111.2.5.1.10	Integer32	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara9 object after the test case is ascertained.
OCT nqaAdminExtPara11	1.3.6.1.4.1.2011.5.25.111.2.5.1.11	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara12 object. The value is automatically assigned by the system after the type of the test case is ascertained.
I32 nqaAdminExtPara12	1.3.6.1.4.1.2011.5.25.111.2.5.1.12	Integer32	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara11 object after the test case is ascertained.
OCT nqaAdminExtPara13	1.3.6.1.4.1.2011.5.25.111.2.5.1.13	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara14 object. The value is automatically assigned by the system after the type of the test case is ascertained.
I32 nqaAdminExtPara14	1.3.6.1.4.1.2011.5.25.111.2.5.1.14	Integer32	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara13 object after the test case is ascertained.
OCT nqaAdminExtPara15	1.3.6.1.4.1.2011.5.25.111.2.5.1.15	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara16 object. The value is automatically assigned by the system after the type of the test case is ascertained.
I32 nqaAdminExtPara16	1.3.6.1.4.1.2011.5.25.111.2.5.1.16	Integer32	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara15 object after the test case is ascertained.
OCT nqaAdminExtPara17	1.3.6.1.4.1.2011.5.25.111.2.5.1.17	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara18 object. The value is automatically assigned by the system after the type of the test case is ascertained.
I32 nqaAdminExtPara18	1.3.6.1.4.1.2011.5.25.111.2.5.1.18	Integer32	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara17 object after the test case is ascertained.
OCT nqaAdminExtPara19	1.3.6.1.4.1.2011.5.25.111.2.5.1.19	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara20 object. The value is automatically assigned by the system after the type of the test case is ascertained.
I32 nqaAdminExtPara20	1.3.6.1.4.1.2011.5.25.111.2.5.1.20	Integer32	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara19 object after the test case is ascertained.
OCT nqaAdminExtPara21	1.3.6.1.4.1.2011.5.25.111.2.5.1.21	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara22 object. The value is automatically assigned by the system after the type of the test case is ascertained.
I32 nqaAdminExtPara22	1.3.6.1.4.1.2011.5.25.111.2.5.1.22	Integer32	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara21 object after the test case is ascertained.
OCT nqaAdminExtPara23	1.3.6.1.4.1.2011.5.25.111.2.5.1.23	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara24 object. The value is automatically assigned by the system after the type of the test case is ascertained.
I32 nqaAdminExtPara24	1.3.6.1.4.1.2011.5.25.111.2.5.1.24	Integer32	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara23 object after the test case is ascertained.
OCT nqaAdminExtPara25	1.3.6.1.4.1.2011.5.25.111.2.5.1.25	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara26 object. The value is automatically assigned by the system after the type of the test case is ascertained.
I32 nqaAdminExtPara26	1.3.6.1.4.1.2011.5.25.111.2.5.1.26	Integer32	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara25 object after the test case is ascertained.
OCT nqaAdminExtPara27	1.3.6.1.4.1.2011.5.25.111.2.5.1.27	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara28 object. The value is automatically assigned by the system after the type of the test case is ascertained.
I32 nqaAdminExtPara28	1.3.6.1.4.1.2011.5.25.111.2.5.1.28	Integer32	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara27 object after the test case is ascertained.
OCT nqaAdminExtPara29	1.3.6.1.4.1.2011.5.25.111.2.5.1.29	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara30 object. The value is automatically assigned by the system after the type of the test case is ascertained.
I32 nqaAdminExtPara30	1.3.6.1.4.1.2011.5.25.111.2.5.1.30	Integer32	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara29 object after the test case is ascertained.
OCT nqaAdminExtPara31	1.3.6.1.4.1.2011.5.25.111.2.5.1.31	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara32 object. The value is automatically assigned by the system after the type of the test case is ascertained.
OCT nqaAdminExtPara32	1.3.6.1.4.1.2011.5.25.111.2.5.1.32	OCTET STRING	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara31 object after the test case is ascertained.
OCT nqaAdminExtPara33	1.3.6.1.4.1.2011.5.25.111.2.5.1.33	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara34 object. The value is automatically assigned by the system after the type of the test case is ascertained.
OCT nqaAdminExtPara34	1.3.6.1.4.1.2011.5.25.111.2.5.1.34	OCTET STRING	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara33 object after the test case is ascertained.
OCT nqaAdminExtPara35	1.3.6.1.4.1.2011.5.25.111.2.5.1.35	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara36 object. The value is automatically assigned by the system after the type of the test case is ascertained.
OCT nqaAdminExtPara36	1.3.6.1.4.1.2011.5.25.111.2.5.1.36	OCTET STRING	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara35 object after the test case is ascertained.
OCT nqaAdminExtPara37	1.3.6.1.4.1.2011.5.25.111.2.5.1.37	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara38 object. The value is automatically assigned by the system after the type of the test case is ascertained.
OCT nqaAdminExtPara38	1.3.6.1.4.1.2011.5.25.111.2.5.1.38	OCTET STRING	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara37 object after the test case is ascertained.
OCT nqaAdminExtPara39	1.3.6.1.4.1.2011.5.25.111.2.5.1.39	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara40 object. The value is automatically assigned by the system after the type of the test case is ascertained.
OCT nqaAdminExtPara40	1.3.6.1.4.1.2011.5.25.111.2.5.1.40	OCTET STRING	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara39 object after the test case is ascertained.
OCT nqaAdminExtPara41	1.3.6.1.4.1.2011.5.25.111.2.5.1.41	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara42 object. The value is automatically assigned by the system after the type of the test case is ascertained.
OCT nqaAdminExtPara42	1.3.6.1.4.1.2011.5.25.111.2.5.1.42	OCTET STRING	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara41 object after the test case is ascertained.
OCT nqaAdminExtPara43	1.3.6.1.4.1.2011.5.25.111.2.5.1.43	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara44 object. The value is automatically assigned by the system after the type of the test case is ascertained.
OCT nqaAdminExtPara44	1.3.6.1.4.1.2011.5.25.111.2.5.1.44	OCTET STRING	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara43 object after the test case is ascertained.
OCT nqaAdminExtPara45	1.3.6.1.4.1.2011.5.25.111.2.5.1.45	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara46 object. The value is automatically assigned by the system after the type of the test case is ascertained.
OCT nqaAdminExtPara46	1.3.6.1.4.1.2011.5.25.111.2.5.1.46	OCTET STRING	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara45 object after the test case is ascertained.
OCT nqaAdminExtPara47	1.3.6.1.4.1.2011.5.25.111.2.5.1.47	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara48 object. The value is automatically assigned by the system after the type of the test case is ascertained.
OCT nqaAdminExtPara48	1.3.6.1.4.1.2011.5.25.111.2.5.1.48	OCTET STRING	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara47 object after the test case is ascertained.
OCT nqaAdminExtPara49	1.3.6.1.4.1.2011.5.25.111.2.5.1.49	OCTET STRING	read-only	This object indicates the description of the nqaAdminExtPara50 object. The value is automatically assigned by the system after the type of the test case is ascertained.
OCT nqaAdminExtPara50	1.3.6.1.4.1.2011.5.25.111.2.5.1.50	OCTET STRING	read-write	This object is a configurable NQA parameter object. Its value and meaning are assigned by the nqaAdminExtPara49 object after the test case is ascertained.
nqaServer	1.3.6.1.4.1.2011.5.25.111.3
ENA nqaServerEnable	1.3.6.1.4.1.2011.5.25.111.3.1	EnableValue	read-write	Enables NQA server, which can be the echo server of TCP, UDP and jitter type test instance.
nqaTcpServerTable	1.3.6.1.4.1.2011.5.25.111.3.2		not-accessible	A table which contains the status of nqa tcp server configuration information.
nqaTcpServerEntry	1.3.6.1.4.1.2011.5.25.111.3.2.1		not-accessible	A table which contains the status of nqa tcp server configuration information. This entry is included not only the tcp server ip address but also the tcp server tcp port. If used for VPN it is also included the VPN name.
IPt nqaTcpServerAddressType	1.3.6.1.4.1.2011.5.25.111.3.2.1.1	InetAddressType	read-create	Specifies the address type of TCP server.
IP nqaTcpServerAddress	1.3.6.1.4.1.2011.5.25.111.3.2.1.2	InetAddress	not-accessible	Specifies the address of TCP server.
INE nqaTcpServerPort	1.3.6.1.4.1.2011.5.25.111.3.2.1.3	InetPortNumber	not-accessible	Specifies the port number on which TCP server is listening.
STR nqaTcpServerVrfName	1.3.6.1.4.1.2011.5.25.111.3.2.1.4	DisplayString	not-accessible	Specifies the VRF (VPN Routing & Forwarding) instances name of the TCP server.
ROW nqaTcpServerStatus	1.3.6.1.4.1.2011.5.25.111.3.2.1.5	RowStatus	read-create	Specifies the operation of the TCP server, creating or deleting.
nqaUdpServerTable	1.3.6.1.4.1.2011.5.25.111.3.3		not-accessible	A table which contains the status of nqa udp server configuration information.
nqaUdpServerEntry	1.3.6.1.4.1.2011.5.25.111.3.3.1		not-accessible	A table which contains the status of nqa udp server configuration information. This entry is includeed not only the udp server ip address but also the udp server udp port.If used for VPN it is also included the VPN name.
IPt nqaUdpServerAddressType	1.3.6.1.4.1.2011.5.25.111.3.3.1.1	InetAddressType	read-create	Specifies the address type of UDP server.
IP nqaUdpServerAddress	1.3.6.1.4.1.2011.5.25.111.3.3.1.2	InetAddress	not-accessible	Specifies the address of UDP server.
INE nqaUdpServerPort	1.3.6.1.4.1.2011.5.25.111.3.3.1.3	InetPortNumber	not-accessible	Specifies the port number on which UDP server is listening.
STR nqaUdpServerVrfName	1.3.6.1.4.1.2011.5.25.111.3.3.1.4	DisplayString	not-accessible	Specifies the VRF (VPN Routing & Forwarding) instances name of the UDP server.
ROW nqaUdpServerStatus	1.3.6.1.4.1.2011.5.25.111.3.3.1.5	RowStatus	read-create	Specifies the operation of the UDP server, creating or deleting.
nqaIcmpServerTable	1.3.6.1.4.1.2011.5.25.111.3.4		not-accessible	A table which contains the status of nqa ICMP server configuration information.
nqaIcmpServerEntry	1.3.6.1.4.1.2011.5.25.111.3.4.1		not-accessible	A table which contains the status of nqa ICMP server configuration information. This entry is included the ICMP server IP address. If used for VPN it is also included the VPN name.
IP nqaIcmpServerAddress	1.3.6.1.4.1.2011.5.25.111.3.4.1.1	InetAddress	not-accessible	Specifies the address of ICMP server.
STR nqaIcmpServerVrfName	1.3.6.1.4.1.2011.5.25.111.3.4.1.2	DisplayString	not-accessible	Specifies the VRF (VPN Routing & Forwarding) instances name of the ICMP server.
IPt nqaIcmpServerAddressType	1.3.6.1.4.1.2011.5.25.111.3.4.1.3	InetAddressType	read-create	Specifies the address type of ICMP server.
ROW nqaIcmpServerStatus	1.3.6.1.4.1.2011.5.25.111.3.4.1.51	RowStatus	read-create	Specifies the operation of the ICMP server, creating or deleting.
nqaStats	1.3.6.1.4.1.2011.5.25.111.4
nqaResultsTable	1.3.6.1.4.1.2011.5.25.111.4.1		not-accessible	Defines the test Results Extend Table for providing the capability of performing test operations at a remote host. The results of these operations are stored in the nqaResultsTable . The operation of this table is same as that of nqaResultsTable.
nqaResultsEntry	1.3.6.1.4.1.2011.5.25.111.4.1.1		not-accessible	The operation of this table is same as that of nqaResultsTable.
I32 nqaResultsIndex	1.3.6.1.4.1.2011.5.25.111.4.1.1.1	Integer32	not-accessible	The result table index and times of dispatching dependency tests. Each test can only reserve 5 records. The result table only contains icmp/dns/dlsw/lspPing/Traceroute/LSP Traceroute/tcp/udp/snmp/dhcp Traceroute information.
I32 nqaResultsHopIndex	1.3.6.1.4.1.2011.5.25.111.4.1.1.2	Integer32	not-accessible	The hop index. If the test type is Traceroute or LSP Traceroute, the entry only defines one hop. For other types, the default value is 1.
INT nqaResultsCompletions	1.3.6.1.4.1.2011.5.25.111.4.1.1.3	INTEGER	read-only	The status of test.
C32 nqaResultsTestAttempts	1.3.6.1.4.1.2011.5.25.111.4.1.1.4	Counter32	read-only	The times of executing tests, which includes the times of successful execution, failed execution and interruption (interrupted by human or system). The current number of test attempts. The value of this object MUST be started at 0.
G32 nqaResultsCurHopCount	1.3.6.1.4.1.2011.5.25.111.4.1.1.5	Gauge32	read-only	It is equal to the hop count index executed by current Traceroute or LSP Traceroute tests. Ping/LSP Ping does not use this entry. The default value is 0.
G32 nqaResultsCurProbeCount	1.3.6.1.4.1.2011.5.25.111.4.1.1.6	Gauge32	read-only	The total count of probe packets of Traceroute or LSP Traceroute test in a hop count index.
C32 nqaResultsRTDOverThresholds	1.3.6.1.4.1.2011.5.25.111.4.1.1.7	Counter32	read-only	The times of successful statistics test RTD (Round Trip Delay) over the threshold.
C32 nqaResultsSumCompletionTime	1.3.6.1.4.1.2011.5.25.111.4.1.1.8	Counter32	read-only	The sum of RTT (response time) of all packets of each hop for executing Traceroute, LSP Traceroute tests. The sum of RTT (response time) of sent packets for executing ping, lsp ping and disman-ping tests and so on.
C32 nqaResultsSumCompletionTime2Low	1.3.6.1.4.1.2011.5.25.111.4.1.1.9	Counter32	read-only	The low order 32 bits of the accumulated squares of completion times (in milliseconds) of NQA operations which complete successfully. Low/High order is defined where the binary number will look as follows: ------------------------------------------------- \| High order 32 bits \| Low order 32 bits \| ------------------------------------------------- For example the number 4294967296 would have all Low order bits as '0' and the rightmost High order bit will be 1 (zeros,1).
C32 nqaResultsSumCompletionTime2High	1.3.6.1.4.1.2011.5.25.111.4.1.1.10	Counter32	read-only	The high order 32 bits of the accumulated squares of completion times (in milliseconds) of NQA operations which complete successfully. See the nqaResultsSumCompletionTime2Low object for a definition of Low/High Order.
G32 nqaResultsCompletionTimeMin	1.3.6.1.4.1.2011.5.25.111.4.1.1.11	Gauge32	read-only	The minimum RTT (for Traceroute and LSP Traceroute, it is the minimum RTT among all the packet of next hop) of all packets for executing a test.
G32 nqaResultsCompletionTimeMax	1.3.6.1.4.1.2011.5.25.111.4.1.1.12	Gauge32	read-only	The maximum RTT (for Traceroute and LSP Traceroute, it is the maximum RTT among all the packets of next hop) of all packets in executing a test.
C32 nqaResultsDisconnects	1.3.6.1.4.1.2011.5.25.111.4.1.1.13	Counter32	read-only	The times of consecutive failures. For connectionless protocol type of test,this number should be zero.
C32 nqaResultsTimeouts	1.3.6.1.4.1.2011.5.25.111.4.1.1.14	Counter32	read-only	The number of occasions when a NQA operation was not completed before a timeout occurred, i.e. nqaAdminCtrlTimeOut was exceeded.
C32 nqaResultsBusies	1.3.6.1.4.1.2011.5.25.111.4.1.1.15	Counter32	read-only	The times of failure to apply resource due to the busy system. such as apply memory or create socket failure.
C32 nqaResultsNoConnections	1.3.6.1.4.1.2011.5.25.111.4.1.1.16	Counter32	read-only	The number of occasions when a NQA operation could not be initiated because the connection to the target has not been established. For all other nqaAdminCtrlType this object will remain zero. This cannot occur for connectionless protocols, but may occur for connection oriented protocols, such as TCP. Since a NQA operation was never initiated, the completion time of these operations are not accumulated, nor do they increment nqaResultsCompletions.
C32 nqaResultsSequenceErrors	1.3.6.1.4.1.2011.5.25.111.4.1.1.17	Counter32	read-only	The number of NQA operation completions received with an unexpected sequence identifier. For all other values of nqaAdminCtrlType this object will remain zero. When this has occurred some of the possible reasons maybe: - a duplicate packet was received - a response was received after it had timed-out - a corrupted packet was received and was not detected
C32 nqaResultsDrops	1.3.6.1.4.1.2011.5.25.111.4.1.1.18	Counter32	read-only	The times probes of the test dropped due to sending or connecting failure.
IPt nqaResultsAddressType	1.3.6.1.4.1.2011.5.25.111.4.1.1.19	InetAddressType	read-only	The destination address type, and the value range can be unknown(0), ipv4(1) and dns(16).
IP nqaResultsAddress	1.3.6.1.4.1.2011.5.25.111.4.1.1.20	InetAddress	read-only	The destination address (TraceRoute is the destination address of each hop, and ping is the destination address of tests).
C32 nqaResultsProbeResponses	1.3.6.1.4.1.2011.5.25.111.4.1.1.21	Counter32	read-only	Number of responses received for the corresponding test. The value of this object MUST be reported as 0 when no probe responses have been received.
C32 nqaResultsSentProbes	1.3.6.1.4.1.2011.5.25.111.4.1.1.22	Counter32	read-only	The value of this object reflects the number of probes sent for the corresponding test. The value of this object MUST be reported as 0 when no probes have been sent.
DAT nqaResultsLastGoodProbe	1.3.6.1.4.1.2011.5.25.111.4.1.1.23	DateAndTime	read-only	Date and time when the last response was received for a probe.
DAT nqaResultsLastGoodPath	1.3.6.1.4.1.2011.5.25.111.4.1.1.24	DateAndTime	read-only	The date and time when the last complete path was determined.
INT nqaResultsTestFinished	1.3.6.1.4.1.2011.5.25.111.4.1.1.25	INTEGER	read-only	The status of test execution.
G32 nqaResultsRttAvg	1.3.6.1.4.1.2011.5.25.111.4.1.1.26	Gauge32	read-only	The average of RTTs that were successfully measured by tests.
G32 nqaResultsLostPacketRatio	1.3.6.1.4.1.2011.5.25.111.4.1.1.27	Gauge32	read-only	The ratio of the packets lost to all packets sent in the test.
nqaHTTPStatsTable	1.3.6.1.4.1.2011.5.25.111.4.2		not-accessible	The statistics collection database. Defines the HTTP Operations Statistics Table for storing the statistics of a HTTP test.
nqaHTTPStatsEntry	1.3.6.1.4.1.2011.5.25.111.4.2.1		not-accessible	Defines an entry in the nqaHTTPStatsTable.
I32 nqaHTTPStatsIndex	1.3.6.1.4.1.2011.5.25.111.4.2.1.1	Integer32	not-accessible	The The HTTP statistics table index and times of dispatching dependency tests.
INT nqaHTTPStatsCompletions	1.3.6.1.4.1.2011.5.25.111.4.2.1.2	INTEGER	read-only	The status of HTTP test.
C32 nqaHTTPStatsRTDOverThresholds	1.3.6.1.4.1.2011.5.25.111.4.2.1.3	Counter32	read-only	The number of HTTP operations RTD (Round Trip Delay) that violate threshold.
C32 nqaHTTPStatsRTTSum	1.3.6.1.4.1.2011.5.25.111.4.2.1.4	Counter32	read-only	The sum of delay time of successful HTTP probes, including the sum of time of DNS query, TCP establishment and packets transmission.
G32 nqaHTTPStatsRTTMin	1.3.6.1.4.1.2011.5.25.111.4.2.1.5	Gauge32	read-only	The minimum value of HTTP probe time.
G32 nqaHTTPStatsRTTMax	1.3.6.1.4.1.2011.5.25.111.4.2.1.6	Gauge32	read-only	The maximum value of HTTP probe time.
C32 nqaHTTPStatsDNSRTTSum	1.3.6.1.4.1.2011.5.25.111.4.2.1.7	Counter32	read-only	The sum of DNS query time.
G32 nqaHTTPStatsDNSRTTMin	1.3.6.1.4.1.2011.5.25.111.4.2.1.8	Gauge32	read-only	The minimum of DNS query time.
G32 nqaHTTPStatsDNSRTTMax	1.3.6.1.4.1.2011.5.25.111.4.2.1.9	Gauge32	read-only	The maximum of DNS query time.
C32 nqaHTTPStatsTCPConnectRTTSum	1.3.6.1.4.1.2011.5.25.111.4.2.1.10	Counter32	read-only	The sum of TCP connection time.
G32 nqaHTTPStatsTCPConnectRTTMin	1.3.6.1.4.1.2011.5.25.111.4.2.1.11	Gauge32	read-only	The minimum value of TCP connection time.
G32 nqaHTTPStatsTCPConnectRTTMax	1.3.6.1.4.1.2011.5.25.111.4.2.1.12	Gauge32	read-only	The maximum value of TCP connection time.
C32 nqaHTTPStatsTransactionRTTSum	1.3.6.1.4.1.2011.5.25.111.4.2.1.13	Counter32	read-only	The sum of transaction time.
G32 nqaHTTPStatsTransactionRTTMin	1.3.6.1.4.1.2011.5.25.111.4.2.1.14	Gauge32	read-only	The minimum value of transaction time.
G32 nqaHTTPStatsTransactionRTTMax	1.3.6.1.4.1.2011.5.25.111.4.2.1.15	Gauge32	read-only	The maximum value of transaction time.
C32 nqaHTTPStatsMessageBodyOctetsSum	1.3.6.1.4.1.2011.5.25.111.4.2.1.16	Counter32	read-only	The sum of the size of the message body received as a response to the HTTP request.
C32 nqaHTTPStatsDNSServerTimeouts	1.3.6.1.4.1.2011.5.25.111.4.2.1.17	Counter32	read-only	The number of requests that timed out during DNS query.
C32 nqaHTTPStatsTCPConnectTimeouts	1.3.6.1.4.1.2011.5.25.111.4.2.1.18	Counter32	read-only	The number of requests that timed out during HTTP connection.
C32 nqaHTTPStatsTransactionTimeouts	1.3.6.1.4.1.2011.5.25.111.4.2.1.19	Counter32	read-only	The number of requests that timed out during HTTP transaction.
C32 nqaHTTPStatsDNSQueryErrors	1.3.6.1.4.1.2011.5.25.111.4.2.1.20	Counter32	read-only	The number of requests that had DNS query errors.
C32 nqaHTTPStatsErrors	1.3.6.1.4.1.2011.5.25.111.4.2.1.21	Counter32	read-only	The number of HTTP transaction failures.
C32 nqaHTTPStatsTcpConnErrors	1.3.6.1.4.1.2011.5.25.111.4.2.1.22	Counter32	read-only	The number of TCP connection failures.
C32 nqaHTTPStatsProbeResponses	1.3.6.1.4.1.2011.5.25.111.4.2.1.23	Counter32	read-only	Number of responses received for the corresponding test. The value of this object MUST be reported as 0 when no probe responses have been received.
C32 nqaHTTPStatsSendProbes	1.3.6.1.4.1.2011.5.25.111.4.2.1.24	Counter32	read-only	The number of sending probes.
C32 nqaHTTPStatsBusies	1.3.6.1.4.1.2011.5.25.111.4.2.1.25	Counter32	read-only	The number of occasions when a HTTP operation could not be initiated because an internal error.
INT nqaHTTPStatsTestFinished	1.3.6.1.4.1.2011.5.25.111.4.2.1.26	INTEGER	read-only	The status of test execution.
G32 nqaHTTPStatsRttAvg	1.3.6.1.4.1.2011.5.25.111.4.2.1.27	Gauge32	read-only	The average of RTTs that were successfully measured by tests.
G32 nqaHTTPStatsLostPacketRatio	1.3.6.1.4.1.2011.5.25.111.4.2.1.28	Gauge32	read-only	The ratio of the packets lost to all packets sent in the test.
nqaJitterStatsTable	1.3.6.1.4.1.2011.5.25.111.4.3		not-accessible	A table which contains the status of latest Jitter operation.
nqaJitterStatsEntry	1.3.6.1.4.1.2011.5.25.111.4.3.1		not-accessible	A table which contains the status of latest Jitter operation. This entry is created only if the nqaAdminCtrlType is jitterAppl.
I32 nqaJitterStatsIndex	1.3.6.1.4.1.2011.5.25.111.4.3.1.1	Integer32	not-accessible	The third index of jitter statistics table.
INT nqaJitterStatsCompletions	1.3.6.1.4.1.2011.5.25.111.4.3.1.2	INTEGER	read-only	The result of the test, which value can be noResult (0), success (1), failure (2) or negotiateFailed (3). If the test is still running, the value will be noResult (0).
C32 nqaJitterStatsRTDOverThresholds	1.3.6.1.4.1.2011.5.25.111.4.3.1.3	Counter32	read-only	The number of tests that violate RTD (Round Trip Delay) threshold.
C32 nqaJitterStatsNumOfRTT	1.3.6.1.4.1.2011.5.25.111.4.3.1.4	Counter32	read-only	The number of RTTs that are successfully measured by tests.
C32 nqaJitterStatsRTTSum	1.3.6.1.4.1.2011.5.25.111.4.3.1.5	Counter32	read-only	The sum of RTTs that are successfully measured.
C32 nqaJitterStatsRTTSum2Low	1.3.6.1.4.1.2011.5.25.111.4.3.1.6	Counter32	read-only	The sum of squares of RTTs that are successfully measured by tests (low order 32 bits).
C32 nqaJitterStatsRTTSum2High	1.3.6.1.4.1.2011.5.25.111.4.3.1.7	Counter32	read-only	The sum of squares of RTTs that are successfully measured by tests (high order 32 bits).
G32 nqaJitterStatsRTTMin	1.3.6.1.4.1.2011.5.25.111.4.3.1.8	Gauge32	read-only	The minimum of RTTs that were successfully measured by tests.
G32 nqaJitterStatsRTTMax	1.3.6.1.4.1.2011.5.25.111.4.3.1.9	Gauge32	read-only	The maximum of RTTs that were successfully measured by tests.
G32 nqaJitterStatsMinOfPositivesSD	1.3.6.1.4.1.2011.5.25.111.4.3.1.10	Gauge32	read-only	The minimum of absolute value of all positive jitter values from source to destination.
G32 nqaJitterStatsMaxOfPositivesSD	1.3.6.1.4.1.2011.5.25.111.4.3.1.11	Gauge32	read-only	The maximum of absolute value of all positive jitter values from source to destination.
C32 nqaJitterStatsNumOfPositivesSD	1.3.6.1.4.1.2011.5.25.111.4.3.1.12	Counter32	read-only	The number of all positive jitter values from source to destination.
C32 nqaJitterStatsSumOfPositivesSD	1.3.6.1.4.1.2011.5.25.111.4.3.1.13	Counter32	read-only	The sum of absolute value of all positive jitter values from source to destination.
C32 nqaJitterStatsSum2OfPositivesSDLow	1.3.6.1.4.1.2011.5.25.111.4.3.1.14	Counter32	read-only	The sum of squares of absolute value of all positive jitter values from source to destination (low order 32 bits).
C32 nqaJitterStatsSum2OfPositivesSDHigh	1.3.6.1.4.1.2011.5.25.111.4.3.1.15	Counter32	read-only	The sum of squares of absolute value of all positive jitter values from source to destination (high order 32 bits).
G32 nqaJitterStatsMinOfNegativesSD	1.3.6.1.4.1.2011.5.25.111.4.3.1.16	Gauge32	read-only	The minimum of absolute value of all negative jitter values from source to destination.
G32 nqaJitterStatsMaxOfNegativesSD	1.3.6.1.4.1.2011.5.25.111.4.3.1.17	Gauge32	read-only	The maximum of absolute value of all negative jitter values from source to destination.
C32 nqaJitterStatsNumOfNegativesSD	1.3.6.1.4.1.2011.5.25.111.4.3.1.18	Counter32	read-only	The number of all negative jitter values from source to destination.
C32 nqaJitterStatsSumOfNegativesSD	1.3.6.1.4.1.2011.5.25.111.4.3.1.19	Counter32	read-only	The sum of absolute value of all negative jitter values from source to destination.
C32 nqaJitterStatsSum2OfNegativesSDLow	1.3.6.1.4.1.2011.5.25.111.4.3.1.20	Counter32	read-only	The sum of squares of absolute value of all negative values from source to destination (low order 32 bits).
C32 nqaJitterStatsSum2OfNegativesSDHigh	1.3.6.1.4.1.2011.5.25.111.4.3.1.21	Counter32	read-only	The sum of squares of absolute value of all negative values from source to destination (high order 32 bits).
G32 nqaJitterStatsMinOfPositivesDS	1.3.6.1.4.1.2011.5.25.111.4.3.1.22	Gauge32	read-only	The minimum of absolute value of all positive jitter values from destination to source.
G32 nqaJitterStatsMaxOfPositivesDS	1.3.6.1.4.1.2011.5.25.111.4.3.1.23	Gauge32	read-only	The maximum of absolute value of all positive jitter values from destination to source.
C32 nqaJitterStatsNumOfPositivesDS	1.3.6.1.4.1.2011.5.25.111.4.3.1.24	Counter32	read-only	The number of all positive jitter values from destination to source.
C32 nqaJitterStatsSumOfPositivesDS	1.3.6.1.4.1.2011.5.25.111.4.3.1.25	Counter32	read-only	The sum of absolute value of all positive jitter values from destination to source.
C32 nqaJitterStatsSum2OfPositivesDSLow	1.3.6.1.4.1.2011.5.25.111.4.3.1.26	Counter32	read-only	The sum of squares of absolute value of all positive jitter values from destination to source (low order 32 bits).
C32 nqaJitterStatsSum2OfPositivesDSHigh	1.3.6.1.4.1.2011.5.25.111.4.3.1.27	Counter32	read-only	The sum of squares of absolute value of all positive jitter values from destination to source (high order 32 bits).
G32 nqaJitterStatsMinOfNegativesDS	1.3.6.1.4.1.2011.5.25.111.4.3.1.28	Gauge32	read-only	The minimum of absolute value of all negative jitter values from destination to source.
G32 nqaJitterStatsMaxOfNegativesDS	1.3.6.1.4.1.2011.5.25.111.4.3.1.29	Gauge32	read-only	The maximum of absolute value of all negative jitter values from destination to source.
C32 nqaJitterStatsNumOfNegativesDS	1.3.6.1.4.1.2011.5.25.111.4.3.1.30	Counter32	read-only	The number of all negative jitter values from destination to source.
C32 nqaJitterStatsSumOfNegativesDS	1.3.6.1.4.1.2011.5.25.111.4.3.1.31	Counter32	read-only	The sum of absolute value of all negative jitter values from destination to source.
C32 nqaJitterStatsSum2OfNegativesDSLow	1.3.6.1.4.1.2011.5.25.111.4.3.1.32	Counter32	read-only	The sum of squares of absolute value of all negative values from destination to source (low order 32 bits).
C32 nqaJitterStatsSum2OfNegativesDSHigh	1.3.6.1.4.1.2011.5.25.111.4.3.1.33	Counter32	read-only	The sum of squares of absolute value of all negative values from destination to source (high order 32 bits).
C32 nqaJitterStatsPacketLossSD	1.3.6.1.4.1.2011.5.25.111.4.3.1.34	Counter32	read-only	The number of packets lost when sent from source to destination.
C32 nqaJitterStatsPacketLossDS	1.3.6.1.4.1.2011.5.25.111.4.3.1.35	Counter32	read-only	The number of packets lost when sent from destination to source.
C32 nqaJitterStatsPacketOutOfSequences	1.3.6.1.4.1.2011.5.25.111.4.3.1.36	Counter32	read-only	The number of packets arrived out of sequence.
C32 nqaJitterStatsErrors	1.3.6.1.4.1.2011.5.25.111.4.3.1.37	Counter32	read-only	The number of errors occurred in the test.
C32 nqaJitterStatsBusies	1.3.6.1.4.1.2011.5.25.111.4.3.1.38	Counter32	read-only	The number of occasions when a test couldn't be initialized because the previous test has not completed.
C32 nqaJitterStatsTimeouts	1.3.6.1.4.1.2011.5.25.111.4.3.1.39	Counter32	read-only	The number of responses arrived over the time.
C32 nqaJitterStatsProbeResponses	1.3.6.1.4.1.2011.5.25.111.4.3.1.40	Counter32	read-only	The number of responses from echo-server for the packets sent by the test.
C32 nqaJitterStatsSentProbes	1.3.6.1.4.1.2011.5.25.111.4.3.1.41	Counter32	read-only	The number of packets sent in the test.
C32 nqaJitterStatsDrops	1.3.6.1.4.1.2011.5.25.111.4.3.1.42	Counter32	read-only	The number of packets that were sent failed in the test.
INT nqaJitterStatsTestFinished	1.3.6.1.4.1.2011.5.25.111.4.3.1.43	INTEGER	read-only	The status of the test, which value can be noFinish (0) or finish (1).
G32 nqaJitterStatsMaxDelaySD	1.3.6.1.4.1.2011.5.25.111.4.3.1.44	Gauge32	read-only	The maximum of all OWD (One Way Delay) from source to destination.
G32 nqaJitterStatsMaxDelayDS	1.3.6.1.4.1.2011.5.25.111.4.3.1.45	Gauge32	read-only	The maximum of all OWD (One Way Delay) from destination to source.
G32 nqaJitterStatsRTTAvg	1.3.6.1.4.1.2011.5.25.111.4.3.1.46	Gauge32	read-only	The average of RTTs that were successfully measured by tests.
G32 nqaJitterStatsPacketLossRatio	1.3.6.1.4.1.2011.5.25.111.4.3.1.47	Gauge32	read-only	The ratio of the packets lost to all packets sent in the test.
G32 nqaJitterStatsAvgJitter	1.3.6.1.4.1.2011.5.25.111.4.3.1.48	Gauge32	read-only	The average of jitter values that were successfully measured by tests.
G32 nqaJitterStatsAvgJitterSD	1.3.6.1.4.1.2011.5.25.111.4.3.1.49	Gauge32	read-only	The average of jitter values from source to destination that were successfully measured by tests.
G32 nqaJitterStatsAvgJitterDS	1.3.6.1.4.1.2011.5.25.111.4.3.1.50	Gauge32	read-only	The average of jitter values from destination to source that were successfully measured by tests.
OCT nqaJitterStatsJitterOut	1.3.6.1.4.1.2011.5.25.111.4.3.1.51	OCTET STRING	read-only	Jitter (RFC1889) at responder.
OCT nqaJitterStatsJitterIn	1.3.6.1.4.1.2011.5.25.111.4.3.1.52	OCTET STRING	read-only	Jitter (RFC1889) at sender.
C32 nqaJitterStatsOWDOverThresholdsSD	1.3.6.1.4.1.2011.5.25.111.4.3.1.53	Counter32	read-only	The number of tests that violate OWD (One Way Delay) threshold from source to destination.
C32 nqaJitterStatsPktLossUnknown	1.3.6.1.4.1.2011.5.25.111.4.3.1.54	Counter32	read-only	The number of packets lost for which we can't determine the direction.
C32 nqaJitterStatsNumOfOWD	1.3.6.1.4.1.2011.5.25.111.4.3.1.55	Counter32	read-only	The number of OWDs that were successfully measured by tests.
C32 nqaJitterStatsOWSumSD	1.3.6.1.4.1.2011.5.25.111.4.3.1.56	Counter32	read-only	The sum of OWDs that were successfully measured by tests from source to destination.
C32 nqaJitterStatsOWSumDS	1.3.6.1.4.1.2011.5.25.111.4.3.1.57	Counter32	read-only	The sum of OWDs that were successfully measured by tests from destination to source.
C32 nqaJitterStatsOWDOverThresholdsDS	1.3.6.1.4.1.2011.5.25.111.4.3.1.58	Counter32	read-only	The number of tests that violate OWD (One Way Delay) threshold from destination to source.
G32 nqaJitterStatsOperOfIcpif	1.3.6.1.4.1.2011.5.25.111.4.3.1.59	Gauge32	read-only	The ICPIF (Calculated Planning Impairment Factor) value for the latest jitter test.
G32 nqaJitterStatsOperOfMos	1.3.6.1.4.1.2011.5.25.111.4.3.1.60	Gauge32	read-only	The MOS (Mean Opinion Score) value for the latest jitter test.
G32 nqaJitterStatsMinDelaySD	1.3.6.1.4.1.2011.5.25.111.4.3.1.61	Gauge32	read-only	The minimum of all one way time from source to destination.
G32 nqaJitterStatsSum2DelaySDLow	1.3.6.1.4.1.2011.5.25.111.4.3.1.62	Gauge32	read-only	The low order 32 bits of the sum of squares of one way time from source to destination.
C32 nqaJitterStatsSum2DelaySDHigh	1.3.6.1.4.1.2011.5.25.111.4.3.1.63	Counter32	read-only	The high order 32 bits of the sum of squares of one way time from source to destination.
G32 nqaJitterStatsMinDelayDS	1.3.6.1.4.1.2011.5.25.111.4.3.1.64	Gauge32	read-only	The minimum of all one way time from destination to source.
G32 nqaJitterStatsSum2DelayDSLow	1.3.6.1.4.1.2011.5.25.111.4.3.1.65	Gauge32	read-only	The low order 32 bits of the sum of squares of one way time from destination to source.
C32 nqaJitterStatsSum2DelayDSHigh	1.3.6.1.4.1.2011.5.25.111.4.3.1.66	Counter32	read-only	The low order 32 bits of the sum of squares of one way time from destination to source.
INT nqaJitterStatsTimeUnit	1.3.6.1.4.1.2011.5.25.111.4.3.1.67	INTEGER	read-only	The unit of the timestamp, ms or us.
G32 nqaJitterStatsAvgDelaySD	1.3.6.1.4.1.2011.5.25.111.4.3.1.68	Gauge32	read-only	The average of one way time from source to destination.
G32 nqaJitterStatsAvgDelayDS	1.3.6.1.4.1.2011.5.25.111.4.3.1.69	Gauge32	read-only	The average of one way time from destination to source.
C32 nqaJitterStatsPktRewriteNum	1.3.6.1.4.1.2011.5.25.111.4.3.1.70	Counter32	read-only	The number of packets have been rewrited.
G32 nqaJitterStatsPktRewriteRatio	1.3.6.1.4.1.2011.5.25.111.4.3.1.71	Gauge32	read-only	The ratio of packets have been rewrited.
C32 nqaJitterStatsPktDisorderNum	1.3.6.1.4.1.2011.5.25.111.4.3.1.72	Counter32	read-only	The number of packets have been disordered.
G32 nqaJitterStatsPktDisorderRatio	1.3.6.1.4.1.2011.5.25.111.4.3.1.73	Gauge32	read-only	The ratio of packets have been disordered.
C32 nqaJitterStatsFragPktDisorderNum	1.3.6.1.4.1.2011.5.25.111.4.3.1.74	Counter32	read-only	The number of packets whose fragments have been disordered.
G32 nqaJitterStatsFragPktDisorderRatio	1.3.6.1.4.1.2011.5.25.111.4.3.1.75	Gauge32	read-only	The ratio of packets whose fragments have been disordered.
nqaFTPStatsTable	1.3.6.1.4.1.2011.5.25.111.4.4		not-accessible	The statistics collection database. Defines the FTP Operations Statistics Table for storing the statistics of a FTP test.
nqaFTPStatsEntry	1.3.6.1.4.1.2011.5.25.111.4.4.1		not-accessible	Defines an entry in the nqaFTPStatsTable.
I32 nqaFTPStatsIndex	1.3.6.1.4.1.2011.5.25.111.4.4.1.1	Integer32	not-accessible	FTP statistics table index and times of dispatching dependency tests.
INT nqaFTPStatsCompletions	1.3.6.1.4.1.2011.5.25.111.4.4.1.2	INTEGER	read-only	The status of FTP test.
C32 nqaFTPStatsRTDOverThresholds	1.3.6.1.4.1.2011.5.25.111.4.4.1.3	Counter32	read-only	The times of successful statistics test RTD (Round Trip Delay) over the threshold.
G32 nqaFTPStatsCtrlConnMaxTime	1.3.6.1.4.1.2011.5.25.111.4.4.1.4	Gauge32	read-only	The maximum value of the control connection time.
G32 nqaFTPStatsCtrlConnMinTime	1.3.6.1.4.1.2011.5.25.111.4.4.1.5	Gauge32	read-only	The minimum value of the control connection time.
G32 nqaFTPStatsCtrlConnAveTime	1.3.6.1.4.1.2011.5.25.111.4.4.1.6	Gauge32	read-only	The average value of the control connection time.
G32 nqaFTPStatsDataConnMaxTime	1.3.6.1.4.1.2011.5.25.111.4.4.1.7	Gauge32	read-only	The maximum value of the data connection time.
G32 nqaFTPStatsDataConnMinTime	1.3.6.1.4.1.2011.5.25.111.4.4.1.8	Gauge32	read-only	The minimum value of the data connection time.
G32 nqaFTPStatsDataConnAveTime	1.3.6.1.4.1.2011.5.25.111.4.4.1.9	Gauge32	read-only	The average value of the data connection time.
G32 nqaFTPStatsConnectSumTimeMax	1.3.6.1.4.1.2011.5.25.111.4.4.1.10	Gauge32	read-only	The maximum value of the FTP probe time.
G32 nqaFTPStatsConnectSumTimeMin	1.3.6.1.4.1.2011.5.25.111.4.4.1.11	Gauge32	read-only	The mininum value of the FTP probe time.
G32 nqaFTPStatsConnectSumTimeAve	1.3.6.1.4.1.2011.5.25.111.4.4.1.12	Gauge32	read-only	The average value of the FTP probe time.
C32 nqaFTPStatsMessageBodyOctetsSum	1.3.6.1.4.1.2011.5.25.111.4.4.1.13	Counter32	read-only	The accumulated octets of a FTP test.
C32 nqaFTPStatsErrors	1.3.6.1.4.1.2011.5.25.111.4.4.1.14	Counter32	read-only	The number of some other errors.
C32 nqaFTPStatsTimeouts	1.3.6.1.4.1.2011.5.25.111.4.4.1.15	Counter32	read-only	The number of occasions when a FTP operation was not completed before a timeout occurred, i.e. nqaAdminCtrlTimeOut was exceeded.
C32 nqaFTPStatsDiscontinued	1.3.6.1.4.1.2011.5.25.111.4.4.1.16	Counter32	read-only	The number of occasions when a FTP test was interrupted by the user.
C32 nqaFTPStatsProbeResponses	1.3.6.1.4.1.2011.5.25.111.4.4.1.17	Counter32	read-only	Number of responses received for the corresponding test. The value of this object MUST be reported as 0 when no probe responses have been received.
C32 nqaFTPStatsSendProbes	1.3.6.1.4.1.2011.5.25.111.4.4.1.18	Counter32	read-only	The number of sending probe
INT nqaFTPStatsTestFinished	1.3.6.1.4.1.2011.5.25.111.4.4.1.19	INTEGER	read-only	The status of test execution.
G32 nqaFTPStatsRttAvg	1.3.6.1.4.1.2011.5.25.111.4.4.1.20	Gauge32	read-only	The average of RTTs that were successfully measured by tests.
G32 nqaFTPStatsLostPacketRatio	1.3.6.1.4.1.2011.5.25.111.4.4.1.21	Gauge32	read-only	The ratio of the packets lost to all packets sent in the test.
nqaMpingStatsTable	1.3.6.1.4.1.2011.5.25.111.4.5		not-accessible	The statistics collection database. Defines the Mping Operations Statistics Table for storing the statistics of a Mping test.
nqaMpingStatsEntry	1.3.6.1.4.1.2011.5.25.111.4.5.1		not-accessible	Defines an entry in the nqaMpingStatsTable.
I32 nqaMpingStatsIndex	1.3.6.1.4.1.2011.5.25.111.4.5.1.1	Integer32	not-accessible	The index of mping statistics table, and the times of dispatching dependency tests.
I32 nqaMpingStatsReceiverIndex	1.3.6.1.4.1.2011.5.25.111.4.5.1.2	Integer32	not-accessible	The index of receiver ,that received the mping request packet and response the reply packet .
IPt nqaMpingStatsTargetAddressType	1.3.6.1.4.1.2011.5.25.111.4.5.1.3	InetAddressType	read-only	The destination address type, and the value range can be unknown(0), ipv4(1) and dns(16).
IP nqaMpingStatsTargetAddress	1.3.6.1.4.1.2011.5.25.111.4.5.1.4	InetAddress	read-only	The destination address .
IP nqaMpingStatsReceiverAddress	1.3.6.1.4.1.2011.5.25.111.4.5.1.5	InetAddress	read-only	The address of mping receiver
INT nqaMpingStatsCompletions	1.3.6.1.4.1.2011.5.25.111.4.5.1.6	INTEGER	read-only	The status of test.
C32 nqaMpingStatsRTDOverThresholds	1.3.6.1.4.1.2011.5.25.111.4.5.1.7	Counter32	read-only	The times of successful statistics test RTD (Round Trip Delay) over the threshold.
C32 nqaMpingStatsSumCompletionTime	1.3.6.1.4.1.2011.5.25.111.4.5.1.8	Counter32	read-only	The sum of RTT (response time) of sent packets.
C32 nqaMpingStatsSumCompletionTime2Low	1.3.6.1.4.1.2011.5.25.111.4.5.1.9	Counter32	read-only	The low order 32 bits of the sum of squares of RTT (response time) for each packet of test execution.
C32 nqaMpingStatsSumCompletionTime2High	1.3.6.1.4.1.2011.5.25.111.4.5.1.10	Counter32	read-only	The high order 32 bits of the sum of squares of RTT (response time) for each packet of test execution.
G32 nqaMpingStatsCompletionTimeMin	1.3.6.1.4.1.2011.5.25.111.4.5.1.11	Gauge32	read-only	The minimum RTT of all packets for executing a test.
G32 nqaMpingStatsCompletionTimeMax	1.3.6.1.4.1.2011.5.25.111.4.5.1.12	Gauge32	read-only	The maximum RTT of all packets in executing a test.
C32 nqaMpingStatsTimeouts	1.3.6.1.4.1.2011.5.25.111.4.5.1.13	Counter32	read-only	The number of occasions when a NQA operation was not completed before a timeout occurred, i.e. nqaAdminCtrlTimeOut was exceeded.
C32 nqaMpingStatsBusies	1.3.6.1.4.1.2011.5.25.111.4.5.1.14	Counter32	read-only	The times of failure to apply resource due to the busy system. such as apply memory or create socket failure.
C32 nqaMpingStatsSequenceErrors	1.3.6.1.4.1.2011.5.25.111.4.5.1.15	Counter32	read-only	The times that sequence error happends.
C32 nqaMpingStatsDrops	1.3.6.1.4.1.2011.5.25.111.4.5.1.16	Counter32	read-only	The times probes of the test dropped due to sending or connecting failure .
C32 nqaMpingStatsProbeResponses	1.3.6.1.4.1.2011.5.25.111.4.5.1.17	Counter32	read-only	The number of received reponse packets.
C32 nqaMpingStatsSentProbes	1.3.6.1.4.1.2011.5.25.111.4.5.1.18	Counter32	read-only	The number of sent packets.
DAT nqaMpingStatsLastGoodProbe	1.3.6.1.4.1.2011.5.25.111.4.5.1.19	DateAndTime	read-only	Date and time when the last response was received for a probe.
INT nqaMpingStatsTestFinished	1.3.6.1.4.1.2011.5.25.111.4.5.1.20	INTEGER	read-only	The status of test execution.
G32 nqaMpingStatsReceiverCount	1.3.6.1.4.1.2011.5.25.111.4.5.1.21	Gauge32	read-only	The current serial number of receivers.
T/F nqaMpingStatsLastFibHit	1.3.6.1.4.1.2011.5.25.111.4.5.1.22	TruthValue	read-only	Whether the fib is hit on the device when receiving the last packet.
G32 nqaMpingStatsRttAvg	1.3.6.1.4.1.2011.5.25.111.4.5.1.23	Gauge32	read-only	The average of RTTs that were successfully measured by tests.
G32 nqaMpingStatsLostPacketRatio	1.3.6.1.4.1.2011.5.25.111.4.5.1.24	Gauge32	read-only	The ratio of the packets lost to all packets sent in the test.
nqaMtracertStatsTable	1.3.6.1.4.1.2011.5.25.111.4.6		not-accessible	The statistics collection database. Defines the Mping Operations Statistics Table for storing the statistics of a Mping test.
nqaMtracertStatsEntry	1.3.6.1.4.1.2011.5.25.111.4.6.1		not-accessible	The operation of this table is same as that of nqaResultsTable.
I32 nqaMtracertStatsIndex	1.3.6.1.4.1.2011.5.25.111.4.6.1.1	Integer32	not-accessible	The index of mping statistics table, and the times of dispatching dependency tests.
I32 nqaMtracertStatsHopIndex	1.3.6.1.4.1.2011.5.25.111.4.6.1.2	Integer32	not-accessible	The index of Mtracert hop
IPt nqaMtracertStatsAddressType	1.3.6.1.4.1.2011.5.25.111.4.6.1.3	InetAddressType	read-only	The destination address type, and the value range can be unknown(0), ipv4(1) and dns(16).
IP nqaMtracertStatsAddress	1.3.6.1.4.1.2011.5.25.111.4.6.1.4	InetAddress	read-only	The destination address (TraceRoute is the source address of the last valuable response package).
INT nqaMtracertStatsCompletions	1.3.6.1.4.1.2011.5.25.111.4.6.1.5	INTEGER	read-only	The status of test.
G32 nqaMtracertStatsCurHopCount	1.3.6.1.4.1.2011.5.25.111.4.6.1.6	Gauge32	read-only	It is equal to the hop count index executed by current tests. The default value is 0.
G32 nqaMtracertStatsCurProbeCount	1.3.6.1.4.1.2011.5.25.111.4.6.1.7	Gauge32	read-only	The total count of probe packets in a hop count index.
C32 nqaMtracertStatsRTDOverThresholds	1.3.6.1.4.1.2011.5.25.111.4.6.1.8	Counter32	read-only	The times of successful statistics test RTD (Round Trip Delay) over the threshold.
C32 nqaMtracertStatsTimeouts	1.3.6.1.4.1.2011.5.25.111.4.6.1.9	Counter32	read-only	The number of occasions when a NQA operation was not completed before a timeout occurred, i.e. nqaAdminCtrlTimeOut was exceeded.
C32 nqaMtracertStatsBusies	1.3.6.1.4.1.2011.5.25.111.4.6.1.10	Counter32	read-only	The times of failure to apply resource due to the busy system. such as apply memory or create socket failure.
C32 nqaMtracertStatsSequenceErrors	1.3.6.1.4.1.2011.5.25.111.4.6.1.11	Counter32	read-only	The times that sequence error happends.
C32 nqaMtracertStatsDrops	1.3.6.1.4.1.2011.5.25.111.4.6.1.12	Counter32	read-only	The times probes of the test dropped due to sending or connecting failure .
C32 nqaMtracertStatsProbeResponses	1.3.6.1.4.1.2011.5.25.111.4.6.1.13	Counter32	read-only	The number of received reponse packets.
C32 nqaMtracertStatsSentProbes	1.3.6.1.4.1.2011.5.25.111.4.6.1.14	Counter32	read-only	The number of sent packets.
DAT nqaMtracertStatsLastGoodProbe	1.3.6.1.4.1.2011.5.25.111.4.6.1.15	DateAndTime	read-only	Date and time when the last response was received for a probe.
DAT nqaMtracertStatsLastGoodPath	1.3.6.1.4.1.2011.5.25.111.4.6.1.16	DateAndTime	read-only	The date and time when the last complete path was determined.
INT nqaMtracertStatsTestFinished	1.3.6.1.4.1.2011.5.25.111.4.6.1.17	INTEGER	read-only	The status of test execution.
G32 nqaMtracertStatsCurPathTTL	1.3.6.1.4.1.2011.5.25.111.4.6.1.18	Gauge32	read-only	The TTL(time to live) of the current path.
G32 nqaMtracertStatsMaxPathTTL	1.3.6.1.4.1.2011.5.25.111.4.6.1.19	Gauge32	read-only	The maximum TTL(time to live) of the path.
G32 nqaMtracertStatsInPkgLossRate	1.3.6.1.4.1.2011.5.25.111.4.6.1.20	Gauge32	read-only	The loss rate of the incoming packets.
G32 nqaMtracertStatsSGPkgLossRate	1.3.6.1.4.1.2011.5.25.111.4.6.1.21	Gauge32	read-only	The loss rate of the packets from source to multicast group.
G32 nqaMtracertStatsInPkgRate	1.3.6.1.4.1.2011.5.25.111.4.6.1.22	Gauge32	read-only	The rate of incoming packets.
G32 nqaMtracertStatsOutPkgRate	1.3.6.1.4.1.2011.5.25.111.4.6.1.23	Gauge32	read-only	The rate of outgoing packets.
G32 nqaMtracertStatsTimeDelay	1.3.6.1.4.1.2011.5.25.111.4.6.1.24	Gauge32	read-only	The time delay of packets from hop to hop.
nqaPathMtuStatsTable	1.3.6.1.4.1.2011.5.25.111.4.7		not-accessible	The statistics collection database. Defines the path MTU Operations Statistics Table for storing the statistics of a path MTU test.
nqaPathMtuStatsEntry	1.3.6.1.4.1.2011.5.25.111.4.7.1		not-accessible	Defines an entry in the nqaPathMtuStatsTable.
I32 nqaPathMtuStatsIndex	1.3.6.1.4.1.2011.5.25.111.4.7.1.1	Integer32	not-accessible	The index of path MTU statistics table, and the times of dispatching dependency tests.
IPt nqaPathMtuStatsAddressType	1.3.6.1.4.1.2011.5.25.111.4.7.1.2	InetAddressType	read-only	The destination address type, and the value range can be unknown(0), ipv4(1) and dns(16).
IP nqaPathMtuStatsAddress	1.3.6.1.4.1.2011.5.25.111.4.7.1.3	InetAddress	read-only	The destination address. It is the source address of the ICMP echo reply packet.
INT nqaPathMtuStatsCompletions	1.3.6.1.4.1.2011.5.25.111.4.7.1.4	INTEGER	read-only	The status of test.
C32 nqaPathMtuStatsSentProbes	1.3.6.1.4.1.2011.5.25.111.4.7.1.5	Counter32	read-only	The number of sent packets.
C32 nqaPathMtuStatsProbeResponses	1.3.6.1.4.1.2011.5.25.111.4.7.1.6	Counter32	read-only	The number of received reponse packets.
G32 nqaPathMtuStatsDiscoveryPathMtuMin	1.3.6.1.4.1.2011.5.25.111.4.7.1.7	Gauge32	read-only	The initial length of packet in the path MTU test. It is the minimal length of a ICMP packet.
G32 nqaPathMtuStatsDiscoveryPathMtuMax	1.3.6.1.4.1.2011.5.25.111.4.7.1.8	Gauge32	read-only	The maximal length of packet in the path MTU test. It is the maximal MTU of local out-interface.
G32 nqaPathMtuStatsOptimumFirstStep	1.3.6.1.4.1.2011.5.25.111.4.7.1.9	Gauge32	read-only	The optimum first step of the path MTU test. It will take effect if the specified step is lower than it.
C32 nqaPathMtuStatsBusies	1.3.6.1.4.1.2011.5.25.111.4.7.1.10	Counter32	read-only	The times of failure to apply resource due to the busy system. such as apply memory or create socket failure.
C32 nqaPathMtuStatsTimeouts	1.3.6.1.4.1.2011.5.25.111.4.7.1.11	Counter32	read-only	The number of occasions when a NQA operation was not completed before a timeout occurred, i.e. nqaAdminCtrlTimeOut was exceeded.
C32 nqaPathMtuStatsDrops	1.3.6.1.4.1.2011.5.25.111.4.7.1.12	Counter32	read-only	The times probes of the test dropped due to sending or connecting failure.
G32 nqaPathMtuStatsPathMtu	1.3.6.1.4.1.2011.5.25.111.4.7.1.13	Gauge32	read-only	The value of current path MTU.
INT nqaPathMtuStatsTestFinished	1.3.6.1.4.1.2011.5.25.111.4.7.1.14	INTEGER	read-only	The status of test execution.
nqaPathJitterStatsTable	1.3.6.1.4.1.2011.5.25.111.4.8		not-accessible	A table which contains the status of latest path jitter operation.
nqaPathJitterStatsEntry	1.3.6.1.4.1.2011.5.25.111.4.8.1		not-accessible	A table which contains the status of latest path jitter operation. This entry is created only if the nqaAdminCtrlType is path jitter.
I32 nqaPathJitterStatsIndex	1.3.6.1.4.1.2011.5.25.111.4.8.1.1	Integer32	not-accessible	The index of path jitter statistics table, and the times of dispatching dependency tests.
I32 nqaPathJitterStatsHopIndex	1.3.6.1.4.1.2011.5.25.111.4.8.1.2	Integer32	not-accessible	The index of path jitter hop.
INT nqaPathJitterStatsCompletions	1.3.6.1.4.1.2011.5.25.111.4.8.1.3	INTEGER	read-only	The status of path jitter test.
IPt nqaPathJitterStatsAddressType	1.3.6.1.4.1.2011.5.25.111.4.8.1.4	InetAddressType	read-only	The destination address type in a hop of path jitter test, and the value range can be unknown(0), ipv4(1) and dns(16).
IP nqaPathJitterStatsAddress	1.3.6.1.4.1.2011.5.25.111.4.8.1.5	InetAddress	read-only	The destination address in a hop of path jitter test.
C32 nqaPathJitterStatsRtdOverThresholds	1.3.6.1.4.1.2011.5.25.111.4.8.1.6	Counter32	read-only	The times of successful executions who's RTD over the threshold in a hop of path jitter test.
C32 nqaPathJitterStatsNumOfRtt	1.3.6.1.4.1.2011.5.25.111.4.8.1.7	Counter32	read-only	The times that statistics RTT successfully in a hop of path jitter test.
C32 nqaPathJitterStatsRttSum	1.3.6.1.4.1.2011.5.25.111.4.8.1.8	Counter32	read-only	The sum of RTTs in a hop of path jitter test.
C32 nqaPathJitterStatsRttSum2Low	1.3.6.1.4.1.2011.5.25.111.4.8.1.9	Counter32	read-only	The low order 32 bits of RTT's square sum that successfully measured in a hop of path jitter test.
C32 nqaPathJitterStatsRttSum2High	1.3.6.1.4.1.2011.5.25.111.4.8.1.10	Counter32	read-only	The high order 32 bits of RTT's square sum that successfully measured in a hop of path jitter test.
G32 nqaPathJitterStatsRttMin	1.3.6.1.4.1.2011.5.25.111.4.8.1.11	Gauge32	read-only	The minimum of RTTs that successfully measured in a hop of path jitter test.
G32 nqaPathJitterStatsRttMax	1.3.6.1.4.1.2011.5.25.111.4.8.1.12	Gauge32	read-only	The maximum of RTTs that successfully measured in a hop of path jitter test.
G32 nqaPathJitterStatsMinOfPositivesSD	1.3.6.1.4.1.2011.5.25.111.4.8.1.13	Gauge32	read-only	The minimum of positive values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
G32 nqaPathJitterStatsMaxOfPositivesSD	1.3.6.1.4.1.2011.5.25.111.4.8.1.14	Gauge32	read-only	The maximum of positive values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
C32 nqaPathJitterStatsNumOfPositivesSD	1.3.6.1.4.1.2011.5.25.111.4.8.1.15	Counter32	read-only	The number of positive values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
C32 nqaPathJitterStatsSumOfPositivesSD	1.3.6.1.4.1.2011.5.25.111.4.8.1.16	Counter32	read-only	The sum of positive values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
C32 nqaPathJitterStatsSum2OfPositivesSDLow	1.3.6.1.4.1.2011.5.25.111.4.8.1.17	Counter32	read-only	The low order 32 bits of square sum of positive values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
C32 nqaPathJitterStatsSum2OfPositivesSDHigh	1.3.6.1.4.1.2011.5.25.111.4.8.1.18	Counter32	read-only	The high order 32 bits of square sum of positive values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
G32 nqaPathJitterStatsMinOfNegativesSD	1.3.6.1.4.1.2011.5.25.111.4.8.1.19	Gauge32	read-only	The minimum of negative values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
G32 nqaPathJitterStatsMaxOfNegativesSD	1.3.6.1.4.1.2011.5.25.111.4.8.1.20	Gauge32	read-only	The maximum of negative values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
C32 nqaPathJitterStatsNumOfNegativesSD	1.3.6.1.4.1.2011.5.25.111.4.8.1.21	Counter32	read-only	The number of negative values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
C32 nqaPathJitterStatsSumOfNegativesSD	1.3.6.1.4.1.2011.5.25.111.4.8.1.22	Counter32	read-only	The sum of negative values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
C32 nqaPathJitterStatsSum2OfNegativesSDLow	1.3.6.1.4.1.2011.5.25.111.4.8.1.23	Counter32	read-only	The low order 32 bits of square sum of negative values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
C32 nqaPathJitterStatsSum2OfNegativesSDHigh	1.3.6.1.4.1.2011.5.25.111.4.8.1.24	Counter32	read-only	The high order 32 bits of square sum of negative values of jitter that measured from packets sent from source to destination in a hop of path jitter test.
G32 nqaPathJitterStatsMinOfPositivesDS	1.3.6.1.4.1.2011.5.25.111.4.8.1.25	Gauge32	read-only	The minimum of positive values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
G32 nqaPathJitterStatsMaxOfPositivesDS	1.3.6.1.4.1.2011.5.25.111.4.8.1.26	Gauge32	read-only	The maximum of positive values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
C32 nqaPathJitterStatsNumOfPositivesDS	1.3.6.1.4.1.2011.5.25.111.4.8.1.27	Counter32	read-only	The number of positive values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
C32 nqaPathJitterStatsSumOfPositivesDS	1.3.6.1.4.1.2011.5.25.111.4.8.1.28	Counter32	read-only	The sum of positive values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
C32 nqaPathJitterStatsSum2OfPositivesDSLow	1.3.6.1.4.1.2011.5.25.111.4.8.1.29	Counter32	read-only	The low order 32 bits of square sum of positive values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
C32 nqaPathJitterStatsSum2OfPositivesDSHigh	1.3.6.1.4.1.2011.5.25.111.4.8.1.30	Counter32	read-only	The high order 32 bits of square sum of positive values of jitter that measured from packetssent from destination to source in a hop of path jitter test.
G32 nqaPathJitterStatsMinOfNegativesDS	1.3.6.1.4.1.2011.5.25.111.4.8.1.31	Gauge32	read-only	The minimum of negative values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
G32 nqaPathJitterStatsMaxOfNegativesDS	1.3.6.1.4.1.2011.5.25.111.4.8.1.32	Gauge32	read-only	The maximum of negative values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
C32 nqaPathJitterStatsNumOfNegativesDS	1.3.6.1.4.1.2011.5.25.111.4.8.1.33	Counter32	read-only	The number of negative values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
C32 nqaPathJitterStatsSumOfNegativesDS	1.3.6.1.4.1.2011.5.25.111.4.8.1.34	Counter32	read-only	The sum of negative values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
C32 nqaPathJitterStatsSum2OfNegativesDSLow	1.3.6.1.4.1.2011.5.25.111.4.8.1.35	Counter32	read-only	The low order 32 bits of square sum of negative values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
C32 nqaPathJitterStatsSum2OfNegativesDSHigh	1.3.6.1.4.1.2011.5.25.111.4.8.1.36	Counter32	read-only	The high order 32 bits of square sum of negative values of jitter that measured from packets sent from destination to source in a hop of path jitter test.
C32 nqaPathJitterStatsPacketLossSD	1.3.6.1.4.1.2011.5.25.111.4.8.1.37	Counter32	read-only	The number of dropped packets sent from source to destination in a hop of path jitter test.
C32 nqaPathJitterStatsPacketLossDS	1.3.6.1.4.1.2011.5.25.111.4.8.1.38	Counter32	read-only	The number of dropped packets sent from destination to source in a hop of path jitter test.
C32 nqaPathJitterStatsPacketOutOfSequences	1.3.6.1.4.1.2011.5.25.111.4.8.1.39	Counter32	read-only	The number of packets that return out of sequence.
C32 nqaPathJitterStatsErrors	1.3.6.1.4.1.2011.5.25.111.4.8.1.40	Counter32	read-only	The number of some other errors type.
C32 nqaPathJitterStatsBusies	1.3.6.1.4.1.2011.5.25.111.4.8.1.41	Counter32	read-only	The number of occasions when a path jitter operation could not be initiated because an internal error.
C32 nqaPathJitterStatsTimeouts	1.3.6.1.4.1.2011.5.25.111.4.8.1.42	Counter32	read-only	The number of occasions when a NQA operation was not completed before a timeout occurred, i.e. nqaAdminCtrlTimeOut was exceeded.
C32 nqaPathJitterStatsProbeResponses	1.3.6.1.4.1.2011.5.25.111.4.8.1.43	Counter32	read-only	The number of responses received for the corresponding test. The value of this object MUST be reported as 0 when no probe responses have been received.
C32 nqaPathJitterStatsSentProbes	1.3.6.1.4.1.2011.5.25.111.4.8.1.44	Counter32	read-only	The value of this object reflects the number of packets sent for the corresponding test. The value of this object MUST be reported as 0 when no probes have been sent.
C32 nqaPathJitterStatsDrops	1.3.6.1.4.1.2011.5.25.111.4.8.1.45	Counter32	read-only	The times probes of the test dropped due to sending failure.
INT nqaPathJitterStatsTestFinished	1.3.6.1.4.1.2011.5.25.111.4.8.1.46	INTEGER	read-only	The status of test execution.
G32 nqaPathJitterStatsMaxDelaySD	1.3.6.1.4.1.2011.5.25.111.4.8.1.47	Gauge32	read-only	The maximum of all OWD (One Way Delay) that measured from packets sent from source to destination in a hop of path jitter test.
G32 nqaPathJitterStatsMaxDelayDS	1.3.6.1.4.1.2011.5.25.111.4.8.1.48	Gauge32	read-only	The maximum of all OWD (One Way Delay) that measured from packets sent from destination to source in a hop of path jitter test.
G32 nqaPathJitterStatsRttAvg	1.3.6.1.4.1.2011.5.25.111.4.8.1.49	Gauge32	read-only	The average of RTTs that were successfully measured in a hop of path jitter test.
G32 nqaPathJitterStatsPacketLossRatio	1.3.6.1.4.1.2011.5.25.111.4.8.1.50	Gauge32	read-only	The ratio of the packets lost to all packets sent in a hop of path jitter test.
G32 nqaPathJitterStatsAvgJitter	1.3.6.1.4.1.2011.5.25.111.4.8.1.51	Gauge32	read-only	The average of jitter values that were successfully measured in a hop of path jitter test.
G32 nqaPathJitterStatsAvgJitterSD	1.3.6.1.4.1.2011.5.25.111.4.8.1.52	Gauge32	read-only	The average value of jitters that measured from packets sent from sourse to destination in a hop of path jitter test.
G32 nqaPathJitterStatsAvgJitterDS	1.3.6.1.4.1.2011.5.25.111.4.8.1.53	Gauge32	read-only	The average value of jitters that measured from packets sent from destination to source in a hop of path jitter test.
OCT nqaPathJitterStatsJitterOut	1.3.6.1.4.1.2011.5.25.111.4.8.1.54	OCTET STRING	read-only	jitter (RFC1889) at responder.
OCT nqaPathJitterStatsJitterIn	1.3.6.1.4.1.2011.5.25.111.4.8.1.55	OCTET STRING	read-only	Jitter (RFC1889) at sender.
C32 nqaPathJitterStatsOwdOverThresholdsSD	1.3.6.1.4.1.2011.5.25.111.4.8.1.56	Counter32	read-only	The number of tests that violate OWD (One Way Delay) threshold from source to destination in a hop of path jitter test.
C32 nqaPathJitterStatsPktLossUnknown	1.3.6.1.4.1.2011.5.25.111.4.8.1.57	Counter32	read-only	The number of lost packets for which we can't determine the direction in a hop of path jitter test.
C32 nqaPathJitterStatsNumOfOwd	1.3.6.1.4.1.2011.5.25.111.4.8.1.58	Counter32	read-only	The number of OWDs that were successfully measured in a hop of path jitter test.
C32 nqaPathJitterStatsOwdSumSD	1.3.6.1.4.1.2011.5.25.111.4.8.1.59	Counter32	read-only	The sum of OWDs that were successfully measured from packets sent from source to destination in a hop of path jitter test.
C32 nqaPathJitterStatsOwdSumDS	1.3.6.1.4.1.2011.5.25.111.4.8.1.60	Counter32	read-only	The sum of OWDs that were successfully measured from packets sent from destination to source in a hop of path jitter test.
C32 nqaPathJitterStatsOwdOverThresholdsDS	1.3.6.1.4.1.2011.5.25.111.4.8.1.61	Counter32	read-only	The number of tests that violate OWD (One Way Delay) threshold from destination to source in a hop of path jitter test.
nqaPppoeStatsTable	1.3.6.1.4.1.2011.5.25.111.4.9		not-accessible	A table which contains the rolling accumulated history of the PPPoE operation.
nqaPppoeStatsEntry	1.3.6.1.4.1.2011.5.25.111.4.9.1		not-accessible	A table which contains the rolling accumulated history of the PPPoE operation. This entry is created only if the nqaAdminCtrlType is pppoe.
I32 nqaPppoeStatsIndex	1.3.6.1.4.1.2011.5.25.111.4.9.1.1	Integer32	not-accessible	The index of PPPoE statistics table, and the executing times of dispatching dependency tests.
I32 nqaPppoeRedialIndex	1.3.6.1.4.1.2011.5.25.111.4.9.1.2	Integer32	not-accessible	The index of PPPoE statistics table, and the redialing times of dispatching dependency tests.
INT nqaPppoeStatsCompletions	1.3.6.1.4.1.2011.5.25.111.4.9.1.3	INTEGER	read-only	The status of PPPoE operation.
INT nqaPppoeStatsCurrentPhase	1.3.6.1.4.1.2011.5.25.111.4.9.1.4	INTEGER	read-only	The current phase of PPPoE operation.
INT nqaPppoeStatsErrorMessage	1.3.6.1.4.1.2011.5.25.111.4.9.1.5	INTEGER	read-only	The error message result of PPPoE operation.
G32 nqaPppoeDiscoveryTimeout	1.3.6.1.4.1.2011.5.25.111.4.9.1.6	Gauge32	read-only	The time for discovery of PPPoE operation.
G32 nqaPppoeLcpTimeout	1.3.6.1.4.1.2011.5.25.111.4.9.1.7	Gauge32	read-only	The time for lcp negotiate of PPPoE operation.
G32 nqaPppoeAuthorizationTimeout	1.3.6.1.4.1.2011.5.25.111.4.9.1.8	Gauge32	read-only	The time for authentication of PPPoE operation.
G32 nqaPppoeNcpTimeout	1.3.6.1.4.1.2011.5.25.111.4.9.1.9	Gauge32	read-only	The time for ncp negotiate of PPPoE operation.
G32 nqaPppoeConnectionTime	1.3.6.1.4.1.2011.5.25.111.4.9.1.10	Gauge32	read-only	The time for connection of PPPoE operation.
G32 nqaPppoeClientSessionId	1.3.6.1.4.1.2011.5.25.111.4.9.1.11	Gauge32	read-only	The client sessionID of PPPoE operation.
IP nqaPppoeClientIpAddress	1.3.6.1.4.1.2011.5.25.111.4.9.1.12	InetAddress	read-only	The client ip address of PPPoE operation.
IP nqaPppoeGatewayIpAddress	1.3.6.1.4.1.2011.5.25.111.4.9.1.13	InetAddress	read-only	The gateway ip address of PPPoE operation.
nqaHistory	1.3.6.1.4.1.2011.5.25.111.5
nqaHistoryTable	1.3.6.1.4.1.2011.5.25.111.5.1		not-accessible	Defines the Remote Operations test History Table for storing the results of a test operation.
nqaHistoryEntry	1.3.6.1.4.1.2011.5.25.111.5.1.1		not-accessible	Defines a table for storing the results of a test operation. Entries in this table are limited by the value of the corresponding nqaAdminParaHistoryRowMax.
I32 nqaHistoryIndex	1.3.6.1.4.1.2011.5.25.111.5.1.1.1	Integer32	not-accessible	The history table index and times for dispatching dependency tests.
I32 nqaHistoryHopIndex	1.3.6.1.4.1.2011.5.25.111.5.1.1.2	Integer32	not-accessible	The hop index. If the test type is Traceroute or LSP Traceroute, the entry only defines one hop. For other types, the default value is 1.
I32 nqaHistoryProbeIndex	1.3.6.1.4.1.2011.5.25.111.5.1.1.3	Integer32	not-accessible	The probe index of tests.
DAT nqaHistoryTimeStamp	1.3.6.1.4.1.2011.5.25.111.5.1.1.4	DateAndTime	read-only	The start time stamp of a probe.
IPt nqaHistoryAddressType	1.3.6.1.4.1.2011.5.25.111.5.1.1.5	InetAddressType	read-only	The address type of history records.
IP nqaHistoryAddress	1.3.6.1.4.1.2011.5.25.111.5.1.1.6	InetAddress	read-only	The destination address of tests. For Traceroute, it is the destination address of each hop.
I32 nqaHistoryCompletionTime	1.3.6.1.4.1.2011.5.25.111.5.1.1.7	Integer32	read-only	The amount of time measured in milliseconds from when a probe was sent to when its response was received or when it timed out. The value of this object is reported as 0 when it is not possible to transmit a probe.
INT nqaHistoryFinishState	1.3.6.1.4.1.2011.5.25.111.5.1.1.8	INTEGER	read-only	The result of a test operation made by a remote host for a particular probe.
I32 nqaHistoryLastRC	1.3.6.1.4.1.2011.5.25.111.5.1.1.9	Integer32	read-only	The last implementation method specific reply code received. If the ICMP Echo capability is being used then a successful probe ends when an ICMP response is received that contains the code ICMP_ECHOREPLY(0). The ICMP responses are defined normally in the ip_icmp include file.
nqaMpingHistoryTable	1.3.6.1.4.1.2011.5.25.111.5.2		not-accessible	Defines the Remote Operations Mping test History Table for storing the results of a test operation.
nqaMpingHistoryEntry	1.3.6.1.4.1.2011.5.25.111.5.2.1		not-accessible	Defines a table for storing the results of a test operation. Entries in this table are limited by the value of the corresponding nqaAdminParaHistoryRowMax.
I32 nqaMpingHistoryIndex	1.3.6.1.4.1.2011.5.25.111.5.2.1.1	Integer32	not-accessible	The Mping history table index and times for dispatching dependency tests.
I32 nqaMpingHistoryReceiverIndex	1.3.6.1.4.1.2011.5.25.111.5.2.1.2	Integer32	not-accessible	The index of receiver ,that received mping request packets and response reply packets .
I32 nqaMpingHistoryResponseIndex	1.3.6.1.4.1.2011.5.25.111.5.2.1.3	Integer32	not-accessible	The index of response packets send by receiver
IPt nqaMpingHistoryAddressType	1.3.6.1.4.1.2011.5.25.111.5.2.1.4	InetAddressType	read-only	The address type of history records.
IP nqaMpingHistoryAddress	1.3.6.1.4.1.2011.5.25.111.5.2.1.5	InetAddress	read-only	The destination address of tests.
IP nqaMpingHistoryReceiverAddress	1.3.6.1.4.1.2011.5.25.111.5.2.1.6	InetAddress	read-only	The source address of response package of tests.
DAT nqaMpingHistoryTimeStamp	1.3.6.1.4.1.2011.5.25.111.5.2.1.7	DateAndTime	read-only	The start time stamp of a probe.
I32 nqaMpingHistoryCompletionTime	1.3.6.1.4.1.2011.5.25.111.5.2.1.8	Integer32	read-only	The completion time of a probe in milliseconds.
INT nqaMpingHistoryFinishState	1.3.6.1.4.1.2011.5.25.111.5.2.1.9	INTEGER	read-only	The result of a test operation made by a remote host for a particular probe.
I32 nqaMpingHistoryLastRC	1.3.6.1.4.1.2011.5.25.111.5.2.1.10	Integer32	read-only	The last reply code received.
T/F nqaMpingHistoryFibHit	1.3.6.1.4.1.2011.5.25.111.5.2.1.11	TruthValue	read-only	Whether the fib is hit on the device which received the packet.
nqaMtracertHistoryTable	1.3.6.1.4.1.2011.5.25.111.5.3		not-accessible	Defines the Remote MtracertOperations test History Table for storing the results of a test operation.
nqaMtracertHistoryEntry	1.3.6.1.4.1.2011.5.25.111.5.3.1		not-accessible	Defines a table for storing the results of a test operation. Entries in this table are limited by the value of the corresponding nqaAdminParaHistoryRowMax.
I32 nqaMtracertHistoryIndex	1.3.6.1.4.1.2011.5.25.111.5.3.1.1	Integer32	not-accessible	The Mtracert history table index and times for dispatching dependency tests.
I32 nqaMtracertHistoryHopIndex	1.3.6.1.4.1.2011.5.25.111.5.3.1.2	Integer32	not-accessible	The index of Mtracert hop.
IPt nqaMtracertHistoryAddressType	1.3.6.1.4.1.2011.5.25.111.5.3.1.3	InetAddressType	read-only	The address type of history records.
IP nqaMtracertHistoryAddress	1.3.6.1.4.1.2011.5.25.111.5.3.1.4	InetAddress	read-only	The destination address of tests. For Traceroute, it is the destination address of each hop.
DAT nqaMtracertHistoryTimeStamp	1.3.6.1.4.1.2011.5.25.111.5.3.1.5	DateAndTime	read-only	The start time stamp of a probe.
I32 nqaMtracertHistoryCompletionTime	1.3.6.1.4.1.2011.5.25.111.5.3.1.6	Integer32	read-only	The amount of time measured in milliseconds from when a probe was sent to when its response was received or when it timed out. The value of this object is reported as 0 when it is not possible to transmit a probe.
I32 nqaMtracertHistoryLastRC	1.3.6.1.4.1.2011.5.25.111.5.3.1.7	Integer32	read-only	The last implementation method specific reply code received. If the ICMP Echo capability is being used then a successful probe ends when an ICMP response is received that contains the code ICMP_ECHOREPLY(0). The ICMP responses are defined normally in the ip_icmp include file.
INT nqaMtracertHistoryCurQueryMode	1.3.6.1.4.1.2011.5.25.111.5.3.1.8	INTEGER	read-only	The current query mode.
U32 nqaMtracertHistoryQueryArrivalTime	1.3.6.1.4.1.2011.5.25.111.5.3.1.9	Unsigned32	read-only	The Query Arrival Time is a 32-bit NTP timestamp specifying the arrival time of the traceroute request packet at this router.
IP nqaMtracertHistoryIncomingIfAddress	1.3.6.1.4.1.2011.5.25.111.5.3.1.10	InetAddress	read-only	This field specifies the address of the interface on which packets from this source and group are expected to arrive, or 0 if unknown.
IP nqaMtracertHistoryOutgoingIfAddress	1.3.6.1.4.1.2011.5.25.111.5.3.1.11	InetAddress	read-only	This field specifies the address of the interface on which packets from this source and group flow to the specified destination, or 0 if unknown.
IP nqaMtracertHistoryPreHopRouterAddress	1.3.6.1.4.1.2011.5.25.111.5.3.1.12	InetAddress	read-only	This field specifies the router from which this router expects packets from this source.
G32 nqaMtracertHistoryInputPacketCount	1.3.6.1.4.1.2011.5.25.111.5.3.1.13	Gauge32	read-only	This field contains the number of multicast packets received for all groups and sources on the incoming interface, or 0xffffffff if no count can be reported. This counter should have the same value as ifInMulticastPkts from the IF-MIB for this interface.
G32 nqaMtracertHistoryOutputPacketCount	1.3.6.1.4.1.2011.5.25.111.5.3.1.14	Gauge32	read-only	This field contains the number of multicast packets that have been transmitted or queued for transmission for all groups and sources on the outgoing interface, or 0xffffffff if no count can be reported. This counter should have the same value as ifOutMulti-castPkts from the IF-MIB for this interface.
G32 nqaMtracertHistoryTotalSGPacketCount	1.3.6.1.4.1.2011.5.25.111.5.3.1.15	Gauge32	read-only	This field counts the number of packets from the specified source forwarded by this router to the specified group, or 0xffffffff if no count can be reported. This counter should have the same value as ipMRoutePkts from the IPMROUTE-STD-MIB for this forwarding entry.
INT nqaMtracertHistoryRtgProtocol	1.3.6.1.4.1.2011.5.25.111.5.3.1.16	INTEGER	read-only	This field describes the routing protocol in use between this router and the previous-hop router.
G32 nqaMtracertHistoryFwdTTL	1.3.6.1.4.1.2011.5.25.111.5.3.1.17	Gauge32	read-only	This field contains the TTL that a packet is required to have before it will be forwarded over the outgoing interface.
INT nqaMtracertHistoryFwdCode	1.3.6.1.4.1.2011.5.25.111.5.3.1.18	INTEGER	read-only	This field contains a forwarding information/error code. noError(1): No error wrongIf(2): Traceroute request arrived on an interface to which this router would not forward for this source,group,destination. pruneSent(3): This router has sent a prune upstream which applies to the source and group in the tracer- oute request. pruneRCVD(4): This router has stopped forwarding for this source and group in response to a request from the next hop router. scoped(5): The group is subject to administrative scoping at this hop. noRoute(6): This router has no route for the source or group and no way to determine a potential route. wrongLastHop(7): This router is not the proper last-hop router. notForwarding(8):This router is not forwarding this source,group out the outgoing interface for an unspecified reason. reachedRP(9): Reached Rendez-vous Point or Core rpfIf(10): Traceroute request arrived on the expected RPF interface for this source,group. noMulticast(11): Traceroute request arrived on an interface which is not enabled for multicast. infoHidden(12): One or more hops have been hidden from this trace. noSpace(13): There was not enough room to insert another response data block in the packet. oldRouter(14): The previous hop router does not understand traceroute requests. adminProhib(15): Traceroute is administratively prohibited.
INT nqaMtracertHistroyFinishState	1.3.6.1.4.1.2011.5.25.111.5.3.1.19	INTEGER	read-only	The finish state of a probe.
nqaVplsMacTracertHistoryTable	1.3.6.1.4.1.2011.5.25.111.5.4		not-accessible	Defines the VPLS mac trace Operations test History Table for storing the results of a test operation.
nqaVplsMacTracertHistoryEntry	1.3.6.1.4.1.2011.5.25.111.5.4.1		not-accessible	Defines a table for storing the results of a test operation. Entries in this table are limited by the value of the corresponding nqaAdminParaHistoryRowMax.
I32 nqaVplsMacTracertHistoryIndex	1.3.6.1.4.1.2011.5.25.111.5.4.1.1	Integer32	not-accessible	The VPLS mac trace history table index and times for dispatching dependency tests.
I32 nqaVplsMacTracertHistoryHopIndex	1.3.6.1.4.1.2011.5.25.111.5.4.1.2	Integer32	not-accessible	The index of VPLS mac trace hop.
I32 nqaVplsMacTracertHistoryResponseIndex	1.3.6.1.4.1.2011.5.25.111.5.4.1.3	Integer32	not-accessible	The index of VPLS mac trace reply packet per hop.
DAT nqaVplsMacTracertHistoryTimeStamp	1.3.6.1.4.1.2011.5.25.111.5.4.1.4	DateAndTime	read-only	The start time stamp of a probe.
IPt nqaVplsMacTracertHistoryAddressType	1.3.6.1.4.1.2011.5.25.111.5.4.1.5	InetAddressType	read-only	The address type of history records.
IP nqaVplsMacTracertHistoryAddress	1.3.6.1.4.1.2011.5.25.111.5.4.1.6	InetAddress	read-only	The destination address of tests. For Traceroute, it is the destination address of each hop.
I32 nqaVplsMacTracertHistoryCompletionTime	1.3.6.1.4.1.2011.5.25.111.5.4.1.7	Integer32	read-only	The completion time of a probe in milliseconds. The amount of time measured in milliseconds from when a probe was sent to when its response was received or when it timed out. The value of this object is reported as 0 when it is not possible to transmit a probe.
INT nqaVplsMacTracertHistoryFinishState	1.3.6.1.4.1.2011.5.25.111.5.4.1.8	INTEGER	read-only	The finish state of a probe.
T/F nqaVplsMacTracertHistoryHitFlag	1.3.6.1.4.1.2011.5.25.111.5.4.1.9	TruthValue	read-only	Hit Flag.
I32 nqaVplsMacTracertHistoryDSCount	1.3.6.1.4.1.2011.5.25.111.5.4.1.10	Integer32	read-only	The count of Downstreams.
T/F nqaVplsMacTracertHistorySuccessPathNode	1.3.6.1.4.1.2011.5.25.111.5.4.1.11	TruthValue	read-only	This object indicates whether it is a node along the path that passes the Trace test. By default, the value is false, indicating that the object is not a node along the path that passes the Trace test.
nqaVplsMacTracertHistoryDSTable	1.3.6.1.4.1.2011.5.25.111.5.5		not-accessible	Defines the VPLS mac trace Operations test History Downstreanm Table for storing the results of a test operation.
nqaVplsMacTracertHistoryDSEntry	1.3.6.1.4.1.2011.5.25.111.5.5.1		not-accessible	Defines a table for storing the results of a test operation. Entries in this table are limited by the value of the corresponding nqaAdminParaHistoryRowMax.
I32 nqaVplsMacTracertHistoryDSIndex	1.3.6.1.4.1.2011.5.25.111.5.5.1.1	Integer32	not-accessible	The VPLS mac trace history DS table index.
IP nqaVplsMacTracertHistoryDSAddress	1.3.6.1.4.1.2011.5.25.111.5.5.1.2	InetAddress	read-only	DS address.
nqaVplsMTraceHistoryTable	1.3.6.1.4.1.2011.5.25.111.5.6		not-accessible	Defines the remote vpls multicast trace operations test history table for storing the results of a test operation.
nqaVplsMTraceHistoryEntry	1.3.6.1.4.1.2011.5.25.111.5.6.1		not-accessible	Defines a table for storing the results of a test operation. Entries in this table are limited by the value of the corresponding nqaAdminParaHistoryRowMax.
I32 nqaVplsMTraceHistoryIndex	1.3.6.1.4.1.2011.5.25.111.5.6.1.1	Integer32	not-accessible	The vpls multicast trace history table index and times for dispatching dependency tests.
I32 nqaVplsMTraceHistoryHopIndex	1.3.6.1.4.1.2011.5.25.111.5.6.1.2	Integer32	not-accessible	The index of vpls multicast trace hop.
I32 nqaVplsMTraceHistoryResponseIndex	1.3.6.1.4.1.2011.5.25.111.5.6.1.3	Integer32	not-accessible	The index of vpls multicast trace responser.
IPt nqaVplsMTraceHistoryResponserAddressType	1.3.6.1.4.1.2011.5.25.111.5.6.1.4	InetAddressType	read-only	The type of history record's Responser address.
IP nqaVplsMTraceHistoryResponserAddress	1.3.6.1.4.1.2011.5.25.111.5.6.1.5	InetAddress	read-only	The Responser address of tests.
IPt nqaVplsMTraceHistoryUpStreamAddressType	1.3.6.1.4.1.2011.5.25.111.5.6.1.6	InetAddressType	read-only	The type of history records' last hop address.
IP nqaVplsMTraceHistoryUpStreamAddress	1.3.6.1.4.1.2011.5.25.111.5.6.1.7	InetAddress	read-only	The last hop address of tests.
U32 nqaVplsMTraceHistoryReceivedTtl	1.3.6.1.4.1.2011.5.25.111.5.6.1.8	Unsigned32	read-only	The value of ttl in the received packet.
INT nqaVplsMTraceHistoryIGMPVersion	1.3.6.1.4.1.2011.5.25.111.5.6.1.9	INTEGER	read-only	The IGMP protocol version.
ENA nqaVplsMTraceHistoryIGMPSnpgEnable	1.3.6.1.4.1.2011.5.25.111.5.6.1.10	EnableValue	read-only	The IGMP snooping enable state.
ENA nqaVplsMTraceHistoryIGMPProxyEnable	1.3.6.1.4.1.2011.5.25.111.5.6.1.11	EnableValue	read-only	The IGMP proxy enable switch.
ENA nqaVplsMTraceHistoryIGMPRouterPortLearningEnable	1.3.6.1.4.1.2011.5.25.111.5.6.1.12	EnableValue	read-only	The IGMP router port learning enable switch.
ENA nqaVplsMTraceHistoryRequireRouterAlertEnable	1.3.6.1.4.1.2011.5.25.111.5.6.1.13	EnableValue	read-only	The route alert requirement enable switch.
INT nqaVplsMTraceHistoryForwardMode	1.3.6.1.4.1.2011.5.25.111.5.6.1.14	INTEGER	read-only	The forward mode value.
T/F nqaVplsMTraceHistoryHitFlag	1.3.6.1.4.1.2011.5.25.111.5.6.1.15	TruthValue	read-only	Whether the fib is hit on the device which received the packet.
T/F nqaVplsMTraceHistoryPWExist	1.3.6.1.4.1.2011.5.25.111.5.6.1.16	TruthValue	read-only	Whether the forward PW is exist.
INT nqaVplsMTraceHistoryGroupPolicy	1.3.6.1.4.1.2011.5.25.111.5.6.1.17	INTEGER	read-only	The ACL judge result.
INT nqaVplsMTraceHistoryCACExist	1.3.6.1.4.1.2011.5.25.111.5.6.1.18	INTEGER	read-only	Whether the connection admission control comfiguration of current VSI is exist.
G32 nqaVplsMTraceHistoryRcvQueryCount	1.3.6.1.4.1.2011.5.25.111.5.6.1.19	Gauge32	read-only	The received query packet number for current IGMP version of current VSI.
G32 nqaVplsMTraceHistoryRcvReportCount	1.3.6.1.4.1.2011.5.25.111.5.6.1.20	Gauge32	read-only	The received report packet number for current IGMP version of current VSI.
G32 nqaVplsMTraceHistoryRcvLeaveCount	1.3.6.1.4.1.2011.5.25.111.5.6.1.21	Gauge32	read-only	The received leave packet number for current IGMP version of current VSI.
DAT nqaVplsMTraceHistoryTimeStamp	1.3.6.1.4.1.2011.5.25.111.5.6.1.22	DateAndTime	read-only	The start time stamp of a probe.
I32 nqaVplsMTraceHistoryCompletionTime	1.3.6.1.4.1.2011.5.25.111.5.6.1.23	Integer32	read-only	The amount of time measured in milliseconds from when a probe was sent to when its response was received or when it timed out. The value of this object is reported as 0 when it is not possible to transmit a probe.
I32 nqaVplsMTraceHistoryLastRC	1.3.6.1.4.1.2011.5.25.111.5.6.1.24	Integer32	read-only	The last implementation method specific reply code received.
I32 nqaVplsMTraceHistoryLastRSC	1.3.6.1.4.1.2011.5.25.111.5.6.1.25	Integer32	read-only	The last implementation method specific reply sub code received.
INT nqaVplsMTraceHistoryFinishState	1.3.6.1.4.1.2011.5.25.111.5.6.1.26	INTEGER	read-only	The finish state of a probe.
INT nqaVplsMTraceHistorySuccessPathNode	1.3.6.1.4.1.2011.5.25.111.5.6.1.27	INTEGER	read-only	Whether the response router is on the path of a probe. The default value is notonPath(2).
nqaMacTraceHistoryTable	1.3.6.1.4.1.2011.5.25.111.5.7		not-accessible	This object defines a list of historical MAC trace test instances for storing the running results of test instances.
nqaMacTraceHistoryEntry	1.3.6.1.4.1.2011.5.25.111.5.7.1		not-accessible	This object defines a table for storing the running results of test instances. The number of entries in this table is limited by the value of nqaAdminParaHistoryRowMax.
I32 nqaMacTraceHistoryIndex	1.3.6.1.4.1.2011.5.25.111.5.7.1.1	Integer32	not-accessible	The object indicates the index of the MAC tract history table and the number of times for dispatching dependency tests.
I32 nqaMacTraceHistoryReceiveOrder	1.3.6.1.4.1.2011.5.25.111.5.7.1.2	Integer32	not-accessible	This object indicates the sequence in which LTRs are received.
I32 nqaMacTraceHistoryTTL	1.3.6.1.4.1.2011.5.25.111.5.7.1.3	Integer32	read-only	This object indicates the TTL of the LTR.
U32 nqaMacTraceHistorySeqNumber	1.3.6.1.4.1.2011.5.25.111.5.7.1.4	Unsigned32	read-only	This object indicates the sequence number of the LTR.
I32 nqaMacTraceHistoryCompletionTime	1.3.6.1.4.1.2011.5.25.111.5.7.1.5	Integer32	read-only	This object indicates the RTT (ms) of the response packet.
T/F nqaMacTraceHistoryForwarded	1.3.6.1.4.1.2011.5.25.111.5.7.1.6	TruthValue	read-only	This object indicates whether the device that sends LTRs continues to forward LTMs.
T/F nqaMacTraceHistoryTerminalMep	1.3.6.1.4.1.2011.5.25.111.5.7.1.7	TruthValue	read-only	This object indicates whether the LTR is sent by an MEP.
HWD nqaMacTraceHistoryRelayAction	1.3.6.1.4.1.2011.5.25.111.5.7.1.8	HWDot1agCfmRelayActionFieldValue	read-only	This object indicates the value of the Relay Action field in the LTR.
HWD nqaMacTraceHistoryIngressAction	1.3.6.1.4.1.2011.5.25.111.5.7.1.9	HWDot1agCfmIngressActionFieldValue	read-only	This object indicates the value of the Ingress Action field in the LTR.
MAC nqaMacTraceHistoryIngressMac	1.3.6.1.4.1.2011.5.25.111.5.7.1.10	MacAddress	read-only	This object indicates the physical MAC address carried in the ingress MAC address field in the LTR.
OCT nqaMacTraceHistoryIngressIfName	1.3.6.1.4.1.2011.5.25.111.5.7.1.11	OCTET STRING	read-only	This object indicates the name of the inbound interface of the LTR.
HWD nqaMacTraceHistoryEgressAction	1.3.6.1.4.1.2011.5.25.111.5.7.1.12	HWDot1agCfmEgressActionFieldValue	read-only	This object indicates the value of the Egress Action field in the LTR.
MAC nqaMacTraceHistoryEgressMac	1.3.6.1.4.1.2011.5.25.111.5.7.1.13	MacAddress	read-only	This object indicates the MAC address in the Egress MAC address field of the LTR.
OCT nqaMacTraceHistoryEgressIfName	1.3.6.1.4.1.2011.5.25.111.5.7.1.14	OCTET STRING	read-only	This object indicates the name of the interface that forwards the LTR.
nqaNotifications	1.3.6.1.4.1.2011.5.25.111.6
NTF nqaResultsProbeFailed	1.3.6.1.4.1.2011.5.25.111.6.1			Generated when a probe failure is detected when the corresponding nqaAdminParaTrapGeneration object is set to probeFailure(0) subject to the value of nqaAdminParaTrapProbeFailureFilter. The object nqaAdminParaTrapProbeFailureFilter can be used to specify the number of successive probe failures that are required before this notification can be generated.(except for HTTP or Jitter or FTP)
NTF nqaResultsTestFailed	1.3.6.1.4.1.2011.5.25.111.6.2			Generated when a nqa test is determined to have failed when the corresponding nqaAdminParaTrapGeneration object is set to testFailure(1). In this instance nqaAdminParaTrapTestFailureFilter should specify the number of probes in a test required to have failed in order to consider the test as failed. (Except for HTTP or Jitter or FTP)
NTF nqaResultsTestCompleted	1.3.6.1.4.1.2011.5.25.111.6.3			Generated at the completion of a nqa test when the corresponding nqaAdminParaTrapGeneration object is set to testCompletion(2).(except for HTTP or Jitter or FTP)
NTF nqaResultsThresholdNotification	1.3.6.1.4.1.2011.5.25.111.6.4			If the time of executing tests exceeds the nqaAdminCtrlThreshold1, the system sends trap information.(except for HTTP or Jitter or FTP)
NTF nqaHTTPStatsProbeFailed	1.3.6.1.4.1.2011.5.25.111.6.5			Generated when a probe failure is detected when the corresponding nqaAdminParaTrapGeneration object is set to probeFailure(0) subject to the value of nqaAdminParaTrapProbeFailureFilter. The object nqaAdminParaTrapProbeFailureFilter can be used to specify the number of successive probe failures that are required before this notification can be generated.(Only for HTTP)
NTF nqaHTTPStatsTestFailed	1.3.6.1.4.1.2011.5.25.111.6.6			Generated when a HTTP test is determined to have failed when the corresponding nqaAdminParaTrapGeneration object is set to testFailure(1). In this instance nqaAdminParaTrapTestFailureFilter should specify the number of probes in a test required to have failed in order to consider the test as failed.(Only for HTTP)
NTF nqaHTTPStatsTestCompleted	1.3.6.1.4.1.2011.5.25.111.6.7			Generated at the completion of a HTTP test when the corresponding nqaAdminParaTrapGeneration object is set to testCompletion(2).
NTF nqaHTTPStatsThresholdNotification	1.3.6.1.4.1.2011.5.25.111.6.8			If the time of executing tests exceeds the nqaAdminCtrlThreshold1 or nqaAdminCtrlThreshold2 or nqaAdminCtrlThreshold3, the system sends trap information.(Only for HTTP)
NTF nqaJitterStatsProbeFailed	1.3.6.1.4.1.2011.5.25.111.6.9			Generated when a probe failure is detected when the corresponding nqaAdminParaTrapGeneration object is set to probeFailure(0) subject to the value of nqaAdminParaTrapProbeFailureFilter. The object nqaAdminParaTrapProbeFailureFilter can be used to specify the number of successive probe failures that are required before this notification can be generated.(Only for Jitter)
NTF nqaJitterStatsTestFailed	1.3.6.1.4.1.2011.5.25.111.6.10			Generated when a Jitter test is determined to have failed when the corresponding nqaAdminParaTrapGeneration object is set to testFailure(1). In this instance nqaAdminParaTrapTestFailureFilter should specify the number of probes in a test required to have failed in order to consider the test as failed.(Only for Jitter)
NTF nqaJitterStatsTestCompleted	1.3.6.1.4.1.2011.5.25.111.6.11			Generated at the completion of a Jitter test when the corresponding nqaAdminParaTrapGeneration object is set to testCompletion(2). (Only for Jitter)
NTF nqaFTPStatsProbeFailed	1.3.6.1.4.1.2011.5.25.111.6.12			Generated when a probe failure is detected when the corresponding nqaAdminParaTrapGeneration object is set to probeFailure(0) subject to the value of nqaAdminParaTrapProbeFailureFilter. The object nqaAdminParaTrapProbeFailureFilter can be used to specify the number of successive probe failures that are required before this notification can be generated.(Only for FTP)
NTF nqaFTPStatsTestFailed	1.3.6.1.4.1.2011.5.25.111.6.13			Generated when a FTP test is determined to have failed when the corresponding nqaAdminParaTrapGeneration object is set to testFailure(1). In this instance nqaAdminParaTrapTestFailureFilter should specify the number of probes in a test required to have failed in order to consider the test as failed.(Only for FTP)
NTF nqaFTPStatsTestCompleted	1.3.6.1.4.1.2011.5.25.111.6.14			Generated at the completion of a FTP test when the corresponding nqaAdminParaTrapGeneration object is set to testCompletion(2). (Only for FTP)
NTF nqaFTPStatsThresholdNotification	1.3.6.1.4.1.2011.5.25.111.6.15			If the time of executing tests exceeds the nqaAdminCtrlThreshold1 or nqaAdminCtrlThreshold2, the system sends trap information.(Only for FTP)
NTF nqaJitterStatsRTDThresholdNotification	1.3.6.1.4.1.2011.5.25.111.6.16			If the time of executing tests exceeds the nqaAdminCtrlThreshold1, the system sends trap information. (Only for jitter)
NTF nqaJitterStatsOWDThresholdNotificationSD	1.3.6.1.4.1.2011.5.25.111.6.17			If the time of executing tests exceeds the nqaAdminCtrlThreshold2 the system sends trap information. (Only for jitter)
NTF nqaJitterStatsOWDThresholdNotificationDS	1.3.6.1.4.1.2011.5.25.111.6.18			If the time of executing tests exceeds the nqaAdminCtrlThreshold3 the system sends trap information. (Only for jitter)
NTF nqaNegotiateFailed	1.3.6.1.4.1.2011.5.25.111.6.19			If negotiation between client and server failed,the system sends trap information.
NTF nqaRisingAlarmNotification	1.3.6.1.4.1.2011.5.25.111.6.20			Sending trap messages when the value of the monitored object exceeds nqaAlarmUpperThreshold.
NTF nqaFallingAlarmNotification	1.3.6.1.4.1.2011.5.25.111.6.21			Sending trap messages when the value of the monitored object is under nqaAlarmLowerThreshold.
NTF nqaFtpSaveRecordNotification	1.3.6.1.4.1.2011.5.25.111.6.22			Sending trap messages when saving a test result to the FTP server is completed.
NTF nqaPppoeStatsTestFailed	1.3.6.1.4.1.2011.5.25.111.6.23			Generated when a PPPoE test is determined to have failed when the corresponding nqaAdminParaTrapGeneration object is set to testFailure(1). (Only for PPPoE))
NTF nqaPppoeStatsTestCompleted	1.3.6.1.4.1.2011.5.25.111.6.24			Generated at the completion of a PPPoE test when the corresponding nqaAdminParaTrapGeneration object is set to testCompletion(2). (Only for PPPoE)
nqaConformance	1.3.6.1.4.1.2011.5.25.111.7
nqaGroups	1.3.6.1.4.1.2011.5.25.111.7.1
nqaBaseGroup	1.3.6.1.4.1.2011.5.25.111.7.1.1			Description.
nqaAdminGroup	1.3.6.1.4.1.2011.5.25.111.7.1.2			Description.
nqaServerGroup	1.3.6.1.4.1.2011.5.25.111.7.1.3			Description.
nqaStatsGroup	1.3.6.1.4.1.2011.5.25.111.7.1.4			Description.
nqaHistoryGroup	1.3.6.1.4.1.2011.5.25.111.7.1.5			Description.
nqaNotificationsGroup	1.3.6.1.4.1.2011.5.25.111.7.1.6			The notification which are required to be supported by implementations of this MIB.
nqaCollectStatsGroup	1.3.6.1.4.1.2011.5.25.111.7.1.7			Description.
nqaAlarmGroup	1.3.6.1.4.1.2011.5.25.111.7.1.8			Description.
nqaFtpSaveRecordGroup	1.3.6.1.4.1.2011.5.25.111.7.1.9			Description.
nqaCompliances	1.3.6.1.4.1.2011.5.25.111.7.2
nqaCompliance	1.3.6.1.4.1.2011.5.25.111.7.2.1			Description.
nqaCollectStats	1.3.6.1.4.1.2011.5.25.111.8
nqaJitterCollectStatsTable	1.3.6.1.4.1.2011.5.25.111.8.1		not-accessible	A table which contains the rolling accumulated history of the Jitter operation.
nqaJitterCollectStatsEntry	1.3.6.1.4.1.2011.5.25.111.8.1.1		not-accessible	A table which contains the rolling accumulated history of the Jitter operation. This entry is created only if the nqaAdminCtrlType is jitterAppl.
I32 nqaJitterCollectStatsIndex	1.3.6.1.4.1.2011.5.25.111.8.1.1.1	Integer32	not-accessible	The third index of jitter collection statistics table.
C32 nqaJitterCollectStatsCompletions	1.3.6.1.4.1.2011.5.25.111.8.1.1.2	Counter32	read-only	The number of the tests that have completed successfully.
C32 nqaJitterCollectStatsRTDOverThresholds	1.3.6.1.4.1.2011.5.25.111.8.1.1.3	Counter32	read-only	The number of tests that violate RTD (Round Trip Delay) threshold.
C32 nqaJitterCollectStatsOWDOverThresholdsSD	1.3.6.1.4.1.2011.5.25.111.8.1.1.4	Counter32	read-only	The number of tests that violate OWD (One Way Delay) threshold from source to destination.
C32 nqaJitterCollectStatsOWDOverThresholdsDS	1.3.6.1.4.1.2011.5.25.111.8.1.1.5	Counter32	read-only	The number of tests that violate OWD (One Way Delay) threshold from destination to source.
C32 nqaJitterCollectStatsNumOfRTT	1.3.6.1.4.1.2011.5.25.111.8.1.1.6	Counter32	read-only	The number of RTTs that are successfully measured by tests.
C32 nqaJitterCollectStatsRTTSum	1.3.6.1.4.1.2011.5.25.111.8.1.1.7	Counter32	read-only	The sum of RTTs that are successfully measured.
C32 nqaJitterCollectStatsRTTSum2Low	1.3.6.1.4.1.2011.5.25.111.8.1.1.8	Counter32	read-only	The sum of squares of RTTs that are successfully measured by tests (low order 32 bits).
C32 nqaJitterCollectStatsRTTSum2High	1.3.6.1.4.1.2011.5.25.111.8.1.1.9	Counter32	read-only	The sum of squares of RTTs that are successfully measured by tests (high order 32 bits).
G32 nqaJitterCollectStatsRTTMin	1.3.6.1.4.1.2011.5.25.111.8.1.1.10	Gauge32	read-only	The minimum of RTTs that were successfully measured by tests.
G32 nqaJitterCollectStatsRTTMax	1.3.6.1.4.1.2011.5.25.111.8.1.1.11	Gauge32	read-only	The maximum of RTTs that were successfully measured by tests.
G32 nqaJitterCollectStatsMinOfPositivesSD	1.3.6.1.4.1.2011.5.25.111.8.1.1.12	Gauge32	read-only	The minimum of absolute value of all positive jitter values from source to destination.
G32 nqaJitterCollectStatsMaxOfPositivesSD	1.3.6.1.4.1.2011.5.25.111.8.1.1.13	Gauge32	read-only	The maximum of absolute value of all positive jitter values from source to destination.
C32 nqaJitterCollectStatsNumOfPositivesSD	1.3.6.1.4.1.2011.5.25.111.8.1.1.14	Counter32	read-only	The number of all positive jitter values from source to destination.
C32 nqaJitterCollectStatsSumOfPositivesSD	1.3.6.1.4.1.2011.5.25.111.8.1.1.15	Counter32	read-only	The sum of absolute value of all positive jitter values from source to destination.
C32 nqaJitterCollectStatsSum2OfPositivesSDLow	1.3.6.1.4.1.2011.5.25.111.8.1.1.16	Counter32	read-only	The sum of squares of absolute value of all positive jitter values from source to destination (low order 32 bits).
C32 nqaJitterCollectStatsSum2OfPositivesSDHigh	1.3.6.1.4.1.2011.5.25.111.8.1.1.17	Counter32	read-only	The sum of squares of absolute value of all positive jitter values from source to destination (high order 32 bits).
G32 nqaJitterCollectStatsMinOfNegativesSD	1.3.6.1.4.1.2011.5.25.111.8.1.1.18	Gauge32	read-only	The minimum of absolute value of all negative jitter values from source to destination.
G32 nqaJitterCollectStatsMaxOfNegativesSD	1.3.6.1.4.1.2011.5.25.111.8.1.1.19	Gauge32	read-only	The maximum of absolute value of all negative jitter values from source to destination.
C32 nqaJitterCollectStatsNumOfNegativesSD	1.3.6.1.4.1.2011.5.25.111.8.1.1.20	Counter32	read-only	The number of all negative jitter values from source to destination.
C32 nqaJitterCollectStatsSumOfNegativesSD	1.3.6.1.4.1.2011.5.25.111.8.1.1.21	Counter32	read-only	The sum of absolute value of all negative jitter values from source to destination.
C32 nqaJitterCollectStatsSum2OfNegativesSDLow	1.3.6.1.4.1.2011.5.25.111.8.1.1.22	Counter32	read-only	The sum of squares of absolute value of all negative values from source to destination (low order 32 bits).
C32 nqaJitterCollectStatsSum2OfNegativesSDHigh	1.3.6.1.4.1.2011.5.25.111.8.1.1.23	Counter32	read-only	The sum of squares of absolute value of all negative values from source to destination (high order 32 bits).
G32 nqaJitterCollectStatsMinOfPositivesDS	1.3.6.1.4.1.2011.5.25.111.8.1.1.24	Gauge32	read-only	The minimum of absolute value of all positive jitter values from destination to source.
G32 nqaJitterCollectStatsMaxOfPositivesDS	1.3.6.1.4.1.2011.5.25.111.8.1.1.25	Gauge32	read-only	The maximum of absolute value of all positive jitter values from destination to source.
C32 nqaJitterCollectStatsNumOfPositivesDS	1.3.6.1.4.1.2011.5.25.111.8.1.1.26	Counter32	read-only	The number of all positive jitter values from destination to source.
C32 nqaJitterCollectStatsSumOfPositivesDS	1.3.6.1.4.1.2011.5.25.111.8.1.1.27	Counter32	read-only	The sum of absolute value of all positive jitter values from destination to source.
C32 nqaJitterCollectStatsSum2OfPositivesDSLow	1.3.6.1.4.1.2011.5.25.111.8.1.1.28	Counter32	read-only	The sum of squares of absolute value of all positive jitter values from destination to source (low order 32 bits).
C32 nqaJitterCollectStatsSum2OfPositivesDSHigh	1.3.6.1.4.1.2011.5.25.111.8.1.1.29	Counter32	read-only	The sum of squares of absolute value of all positive jitter values from destination to source (high order 32 bits).
G32 nqaJitterCollectStatsMinOfNegativesDS	1.3.6.1.4.1.2011.5.25.111.8.1.1.30	Gauge32	read-only	The minimum of absolute value of all negative jitter values from destination to source.
G32 nqaJitterCollectStatsMaxOfNegativesDS	1.3.6.1.4.1.2011.5.25.111.8.1.1.31	Gauge32	read-only	The maximum of absolute value of all negative jitter values from destination to source.
C32 nqaJitterCollectStatsNumOfNegativesDS	1.3.6.1.4.1.2011.5.25.111.8.1.1.32	Counter32	read-only	The number of all negative jitter values from destination to source.
C32 nqaJitterCollectStatsSumOfNegativesDS	1.3.6.1.4.1.2011.5.25.111.8.1.1.33	Counter32	read-only	The sum of absolute value of all negative jitter values from destination to source.
C32 nqaJitterCollectStatsSum2OfNegativesDSLow	1.3.6.1.4.1.2011.5.25.111.8.1.1.34	Counter32	read-only	The sum of squares of absolute value of all negative values from destination to source (low order 32 bits).
C32 nqaJitterCollectStatsSum2OfNegativesDSHigh	1.3.6.1.4.1.2011.5.25.111.8.1.1.35	Counter32	read-only	The sum of squares of absolute value of all negative values from destination to source (high order 32 bits).
G32 nqaJitterCollectStatsMaxDelaySD	1.3.6.1.4.1.2011.5.25.111.8.1.1.36	Gauge32	read-only	The maximum of all OWD (One Way Delay) from source to destination.
G32 nqaJitterCollectStatsMaxDelayDS	1.3.6.1.4.1.2011.5.25.111.8.1.1.37	Gauge32	read-only	The maximum of all OWD (One Way Delay) from destination to source.
C32 nqaJitterCollectStatsNumOfOWD	1.3.6.1.4.1.2011.5.25.111.8.1.1.38	Counter32	read-only	The number of OWDs that were successfully measured by tests.
C32 nqaJitterCollectStatsOWSumSD	1.3.6.1.4.1.2011.5.25.111.8.1.1.39	Counter32	read-only	The sum of OWDs that were successfully measured by tests from source to destination.
C32 nqaJitterCollectStatsOWSumDS	1.3.6.1.4.1.2011.5.25.111.8.1.1.40	Counter32	read-only	The sum of OWDs that were successfully measured by tests from destination to source.
C32 nqaJitterCollectStatsPacketLossSD	1.3.6.1.4.1.2011.5.25.111.8.1.1.41	Counter32	read-only	The number of packets lost when sent from source to destination.
C32 nqaJitterCollectStatsPacketLossDS	1.3.6.1.4.1.2011.5.25.111.8.1.1.42	Counter32	read-only	The number of packets lost when sent from destination to source.
C32 nqaJitterCollectStatsPacketLossUnknown	1.3.6.1.4.1.2011.5.25.111.8.1.1.43	Counter32	read-only	The number of packets lost for which we can't determine the direction.
C32 nqaJitterCollectStatsPacketOutOfSequences	1.3.6.1.4.1.2011.5.25.111.8.1.1.44	Counter32	read-only	The number of packets arrived out of sequence.
G32 nqaJitterCollectStatsPacketLossRatio	1.3.6.1.4.1.2011.5.25.111.8.1.1.45	Gauge32	read-only	The ratio of the packets lost to all packets sent in the test.
C32 nqaJitterCollectStatsErrors	1.3.6.1.4.1.2011.5.25.111.8.1.1.46	Counter32	read-only	The number of errors occurred in the test.
C32 nqaJitterCollectStatsBusies	1.3.6.1.4.1.2011.5.25.111.8.1.1.47	Counter32	read-only	The number of occasions when a test couldn't be initialized because the previous test has not completed.
C32 nqaJitterCollectStatsTimeouts	1.3.6.1.4.1.2011.5.25.111.8.1.1.48	Counter32	read-only	The number of responses arrived over the time.
C32 nqaJitterCollectStatsProbeResponses	1.3.6.1.4.1.2011.5.25.111.8.1.1.49	Counter32	read-only	The number of responses from echo-server for the packets sent by the test.
C32 nqaJitterCollectStatsSentProbes	1.3.6.1.4.1.2011.5.25.111.8.1.1.50	Counter32	read-only	The number of packets sent in the test.
C32 nqaJitterCollectStatsDrops	1.3.6.1.4.1.2011.5.25.111.8.1.1.51	Counter32	read-only	The number of packets that were sent failed in the test.
G32 nqaJitterCollectStatsRTTAvg	1.3.6.1.4.1.2011.5.25.111.8.1.1.52	Gauge32	read-only	The average of RTTs that were successfully measured by tests.
G32 nqaJitterCollectStatsAvgJitter	1.3.6.1.4.1.2011.5.25.111.8.1.1.53	Gauge32	read-only	The average of jitter values that were successfully measured by tests.
G32 nqaJitterCollectStatsAvgJitterSD	1.3.6.1.4.1.2011.5.25.111.8.1.1.54	Gauge32	read-only	The average of jitter values from source to destination that were successfully measured by tests.
G32 nqaJitterCollectStatsAvgJitterDS	1.3.6.1.4.1.2011.5.25.111.8.1.1.55	Gauge32	read-only	The average of jitter values from destination to source that were successfully measured by tests.
OCT nqaJitterCollectStatsJitterOut	1.3.6.1.4.1.2011.5.25.111.8.1.1.56	OCTET STRING	read-only	Jitter (RFC1889) at responder.
OCT nqaJitterCollectStatsJitterIn	1.3.6.1.4.1.2011.5.25.111.8.1.1.57	OCTET STRING	read-only	Jitter (RFC1889) at sender.
G32 nqaJitterCollectStatsMinDelaySD	1.3.6.1.4.1.2011.5.25.111.8.1.1.58	Gauge32	read-only	The minimum of all OWD (One Way Delay) from source to destination.
G32 nqaJitterCollectStatsMinDelayDS	1.3.6.1.4.1.2011.5.25.111.8.1.1.59	Gauge32	read-only	The minimum of all OWD (One Way Delay) from destination to source.
G32 nqaJitterCollectStatsAvgDelaySD	1.3.6.1.4.1.2011.5.25.111.8.1.1.60	Gauge32	read-only	The average of all OWD (One Way Delay) from source to destination.
G32 nqaJitterCollectStatsAvgDelayDS	1.3.6.1.4.1.2011.5.25.111.8.1.1.61	Gauge32	read-only	The average of all OWD (One Way Delay) from destination to source.
C32 nqaJitterCollectStatsPktRewriteNum	1.3.6.1.4.1.2011.5.25.111.8.1.1.62	Counter32	read-only	The number of all the packets have been rewrited.
G32 nqaJitterCollectStatsPktRewriteRatio	1.3.6.1.4.1.2011.5.25.111.8.1.1.63	Gauge32	read-only	The ratio of all the packets have been rewrited.
C32 nqaJitterCollectStatsPktDisorderNum	1.3.6.1.4.1.2011.5.25.111.8.1.1.64	Counter32	read-only	The number of all the packets have been disordered.
G32 nqaJitterCollectStatsPktDisorderRatio	1.3.6.1.4.1.2011.5.25.111.8.1.1.65	Gauge32	read-only	The ratio of all the packets have been disordered.
C32 nqaJitterCollectStatsFragPktDisorderNum	1.3.6.1.4.1.2011.5.25.111.8.1.1.66	Counter32	read-only	The number of all the packets whose fragments have been disordered.
G32 nqaJitterCollectStatsFragPktDisorderRatio	1.3.6.1.4.1.2011.5.25.111.8.1.1.67	Gauge32	read-only	The ratio of all the packets whose fragments have been disordered.
nqaAlarm	1.3.6.1.4.1.2011.5.25.111.9
I32 nqaMaxAlarmNum	1.3.6.1.4.1.2011.5.25.111.9.1	Integer32	read-only	Maximum number of alarms.
I32 nqaMaxEventNum	1.3.6.1.4.1.2011.5.25.111.9.2	Integer32	read-only	Maximum number of events that alarms can trigger.
nqaAlarmTable	1.3.6.1.4.1.2011.5.25.111.9.3		not-accessible	A list of alarm entries.
nqaAlarmEntry	1.3.6.1.4.1.2011.5.25.111.9.3.1		not-accessible	A list of parameters that set up a periodic checking for alarm conditions.
I32 nqaAlarmIndex	1.3.6.1.4.1.2011.5.25.111.9.3.1.1	Integer32	not-accessible	Uniquely identifies a row in the nqaAlarmTable.
INT nqaAlarmVariable	1.3.6.1.4.1.2011.5.25.111.9.3.1.11	INTEGER	read-create	The type of the particular variable to be sampled.
INT nqaAlarmSampleType	1.3.6.1.4.1.2011.5.25.111.9.3.1.12	INTEGER	read-create	delta(1): relative value absolute(2): absolute value Relative value: indicates the relative value to the last sampling. Currently, only absolute(2) is supported.
I32 nqaAlarmValue	1.3.6.1.4.1.2011.5.25.111.9.3.1.13	Integer32	read-only	The actual value of the monitored object is compared with the upper limit and lower limit.
INT nqaAlarmStartUpNqaAlarm	1.3.6.1.4.1.2011.5.25.111.9.3.1.14	INTEGER	read-create	The alarm that may be sent when this entry is first set to valid. If the first sample after this entry becomes valid is greater than or equal to the risingThreshold and alarmStartupAlarm is equal to risingAlarm(1) or risingOrFallingAlarm(3), then a single rising alarm will be generated. If the first sample after this entry becomes valid is less than or equal to the fallingThreshold and alarmStartupAlarm is equal to fallingAlarm(2) or risingOrFallingAlarm(3), then a single falling alarm will be generated.
I32 nqaAlarmRisingThreshold	1.3.6.1.4.1.2011.5.25.111.9.3.1.15	Integer32	read-create	Set the upper limit of the alarm.
I32 nqaAlarmFallingThreshold	1.3.6.1.4.1.2011.5.25.111.9.3.1.16	Integer32	read-create	Set the lower limit of the alarm.
I32 nqaAlarmRisingEventIndex	1.3.6.1.4.1.2011.5.25.111.9.3.1.17	Integer32	read-create	Index of the event triggered when the node value exceeds the upper limit.
I32 nqaAlarmFallingEventIndex	1.3.6.1.4.1.2011.5.25.111.9.3.1.18	Integer32	read-create	Index of the event triggered when the node value is under the lower limit.
OCT nqaAlarmDescription	1.3.6.1.4.1.2011.5.25.111.9.3.1.19	OCTET STRING	read-create	Alarm Description.
ROW nqaAlarmStatus	1.3.6.1.4.1.2011.5.25.111.9.3.1.51	RowStatus	read-create	The status of the alarm row.
nqaEventTable	1.3.6.1.4.1.2011.5.25.111.9.4		not-accessible	A list of events to be generated.
nqaEventEntry	1.3.6.1.4.1.2011.5.25.111.9.4.1		not-accessible	A set of parameters that describe an event to be generated when certain conditions are met.
I32 nqaEventIndex	1.3.6.1.4.1.2011.5.25.111.9.4.1.1	Integer32	not-accessible	Uniquely identifies a row in the nqaEventTable.
INT nqaEventType	1.3.6.1.4.1.2011.5.25.111.9.4.1.11	INTEGER	read-create	Event type, that is, behaviors for processing events: none(1): no behavior log(2): keeping logs trap(3): sending trap messages logandtrap(4): keeping logs and sending trap messages linkage(5): start the linkaged test-instance.
OCT nqaEventDescription	1.3.6.1.4.1.2011.5.25.111.9.4.1.12	OCTET STRING	read-create	Event description.
OCT nqaEventAdminName	1.3.6.1.4.1.2011.5.25.111.9.4.1.13	OCTET STRING	read-create	Administrator name of event test instance.
OCT nqaEventOperationTag	1.3.6.1.4.1.2011.5.25.111.9.4.1.14	OCTET STRING	read-create	Operation tag of event test instance.
ROW nqaEventStatus	1.3.6.1.4.1.2011.5.25.111.9.4.1.51	RowStatus	read-create	The status of the event row.
nqaSaveRecord	1.3.6.1.4.1.2011.5.25.111.10
ENA nqaFtpSaveRecordEnable	1.3.6.1.4.1.2011.5.25.111.10.1	EnabledStatus	read-write	Identifies whether saving test results to the FTP server through FTP is enabled. enable(1) disable(2) By default, the value is disable(2).
IP nqaFtpSaveRecordIpAddr	1.3.6.1.4.1.2011.5.25.111.10.2	InetAddress	read-write	Set the IP address of the FTP server to which test results are saved.
OCT nqaFtpSaveRecordVrfName	1.3.6.1.4.1.2011.5.25.111.10.3	OCTET STRING	read-write	Set the name of the VRF instance for the FTP server to which test results are saved.
OCT nqaFtpSaveRecordUserName	1.3.6.1.4.1.2011.5.25.111.10.4	OCTET STRING	read-write	Set the user name of the FTP server to which test results are saved.
OCT nqaFtpSaveRecordPassword	1.3.6.1.4.1.2011.5.25.111.10.5	OCTET STRING	read-write	Set the password used when the test results are saved to the FTP server.
OCT nqaFtpSaveRecordFileName	1.3.6.1.4.1.2011.5.25.111.10.6	OCTET STRING	read-write	Set the file name of used by the FTP server to save test results.
I32 nqaFtpSaveRecordItemNum	1.3.6.1.4.1.2011.5.25.111.10.7	Integer32	read-write	The value of this object identifies the number of NQA test results that can be saved in a file created on the FTP server. The default value is 100000.
I32 nqaFtpSaveRecordTime	1.3.6.1.4.1.2011.5.25.111.10.8	Integer32	read-write	The value of this object identifies the duration that NQA test results can be saved in a file created on the FTP server. The default duration is 60 minutes.
ENA nqaFtpSaveRecordNotificationEnable	1.3.6.1.4.1.2011.5.25.111.10.9	EnabledStatus	read-write	Set whether to send trap messages when saving test results to the FTP server is completed. By default, the value is disable(2).
OCT nqaFtpSaveRecordLastFileName	1.3.6.1.4.1.2011.5.25.111.10.10	OCTET STRING	read-only	Set the name of the file used to save the last test record to the FTP server.

RFC description

Manages Huawei Network Quality Analyzer test instances, scheduling, and IP SLA-equivalent performance result storage.

Start monitoring Huawei router/switch (Network Quality Analysis active probes) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download NQA-MIB

What Is NQA-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

RFC description