NETGEAR-ROUTE-POLICY-MIB

All MIBs › NETGEAR-ROUTE-POLICY-MIB

Organization: Netgear Inc

Last Updated: 2012-10-01

Category: IP Routing

Description: Configures route policy maps, match conditions, and set actions for routing control on Netgear switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is NETGEAR-ROUTE-POLICY-MIB?

NETGEAR-ROUTE-POLICY-MIB is a Netgear private MIB, built on the Broadcom FASTPATH switch software stack, that configures route policy maps, match statements, and set actions used to control route redistribution and selection on Netgear Layer 3 switches/routers. It exposes configuration-oriented data — policy statement sequencing, action types, and per-interface application of route policies — rather than hardware environmental or fault data. Its relevance to software status monitoring is checking whether route policy statements are correctly applied and active on routing interfaces (via row status), which is a configuration-integrity check confirming routing behavior matches intent rather than a hardware-health check. It depends on the broader FASTPATH/Netgear routing MIB set and standard ifIndex-based interface association. It is deployed on Netgear Layer 3 managed switches or routers using policy-based routing to control route redistribution between protocols. Engineers can download the NETGEAR-ROUTE-POLICY-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in NETGEAR-ROUTE-POLICY-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Netgear Layer 3 managed switch/router (FASTPATH-based)

Monitoring Examples

An administrator would inspect fastpathRoutePolicyStatementEntry together with fastpathRoutePolicySequence and fastpathRoutePolicyStmtActionType to confirm the order and effect of each policy clause, then check fastpathRoutePolicyIfTable/fastpathRoutePolicyIfEntry and fastpathRoutePolicyIfRowStatus to verify a given routing interface actually has the intended policy attached and active. If fastpathRoutePolicyIfRowStatus shows a row as notInService when it should be active, that reveals a policy application error explaining why expected routes aren't being filtered or redistributed as configured.

What Can Be Monitored

route policy statement sequence and action type
route policy application per interface
route policy interface row status

Imported Objects

From FASTPATH-ROUTING-MIB

fastPathRouting

MODULE-IDENTITY

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero
ifIndex	OBJECT-TYPE

From RFC1213-MIB

DisplayString

From SNMPv2-SMI

MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
fastPathRoutePolicy	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20			The MIB definitions for Route Policy system.
fastpathRoutePolicyNameTable	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.1		not-accessible	Table to configure or fetch current list of route-map statements
fastpathRoutePolicyNameEntry	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.1.1		not-accessible	Each entry in this table corresponds to a route-map statement
STR fastpathRoutePolicyName	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.1.1.1	DisplayString	read-create	The name of a Route Map statement.
FAS fastpathRoutePolicyStmtActionType	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.1.1.2	FastpathRoutePolicyAction	read-create	The action associated with this route-map statement. This can be either Permit/Deny
U32 fastpathRoutePolicySequence	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.1.1.3	Unsigned32	read-create	Route Maps are linked together using sequence numbers. All Route Maps with the same index and with different sequence numbers are linked together and processed in order of increasing sequence number.
ROW fastpathRoutePolicyNameRowStatus	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.1.1.4	RowStatus	read-create	Controls creation and deletion of Row Status entries.
fastpathRoutePolicyStamentTable	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.2		not-accessible	Table to configure match or set statements in a route-map statement.
fastpathRoutePolicyStatementEntry	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.2.1		not-accessible	Each entry describes match and set terms in a route-map statement if configured
STR fastpathRoutePolicyStmtName	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.2.1.1	DisplayString	not-accessible	The name of a Route Map.
U32 fastpathRoutePolicyStmtSeqNum	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.2.1.2	Unsigned32	not-accessible	Route Maps are linked together using sequence numbers. All Route Maps with the same index and with different sequence numbers are linked together and processed in order of increasing sequence number.
FAS fastpathRoutePolicyStmtAction	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.2.1.3	FastpathRoutePolicyAction	not-accessible	The action associated with this route-map statement. This can be either Permit/Deny
STR fastpathRoutePolicyStmtMatchIpv4AclList	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.2.1.4	DisplayString	read-write	The string containing a list of IPv4 ACLs. This list contains either IPV4 standard ACL/IPV4 extended ACL/ named IPv4 ACL. In a single match statement, up to a maximum of 16 IPV4 ACLs can be included.
STR fastpathRoutePolicyStmtMatchIpv4AclDelList	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.2.1.5	DisplayString	read-write	The string containing a list of IPv4 ACLs. This list contains either IPV4 standard ACL/IPV4 extended ACL/ named IPv4 ACL. In a single match statement, up to a maximum of 16 IPV4 ACLs can be included.This list is used to delete already configured match list of IPv4 ACLs in route-map statement.Earlier this list should have configured through MIB object fastpathRoutePolicyStmtMatchIpv4AclList
STR fastpathRoutePolicyStmtMatchMacAclList	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.2.1.6	DisplayString	read-write	The string containing a list of MAC ACLs. This list contains upto 16 MAC ACL names that can be included in a match statement.
STR fastpathRoutePolicyStmtMatchMacAclDelList	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.2.1.7	DisplayString	read-write	The string containing a list of MAC ACLs. This list contains upto 16 MAC ACL names that can be included in a match statement. This MIB object is used to delete MAC ACL lists matched in a route-map statement via fastpathRoutePolicyStmtMatchMacAclList.
U32 fastpathRoutePolicyStmtMatchPacketLengthRangeMin	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.2.1.8	Unsigned32	read-write	Minimum value in the packet length range in a match length term. A value of zero is used to disable/remove minimum length configuration.
U32 fastpathRoutePolicyStmtMatchPacketLengthRangeMax	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.2.1.9	Unsigned32	read-write	Maximum value in the packet length range in a match length term. A value of zero is used to disable/remove maximum length configuration.
STR fastpathRoutePolicyStmtSetIpNextHopList	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.2.1.10	DisplayString	read-write	The string containing a list of next-hop IP addresses. Upto a maximum of 16 IP addresses can be specified
STR fastpathRoutePolicyStmtSetIpNextHopDelList	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.2.1.11	DisplayString	read-write	The string containing a list of next-hop IP addresses. Upto a maximum of 16 IP addresses can be specified.This MIB object is used to delete IP next-hop list configured via fastpathRoutePolicyStmtSetIpNextHopList
STR fastpathRoutePolicyStmtSetDefaultIpNextHopList	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.2.1.12	DisplayString	read-write	The string containing a list of default next-hop IP addresses. Upto a maximum of 16 IP addresses can be specified
STR fastpathRoutePolicyStmtSetDefaultIpNextHopDelList	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.2.1.13	DisplayString	read-write	The string containing a list of default next-hop IP addresses. Upto a maximum of 16 IP addresses can be specified.This MIB object is used to delete IP default next-hop list configured via fastpathRoutePolicyStmtSetDefaultIpNextHopList
FAS fastpathRoutePolicyStmtSetIpPrecedence	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.2.1.14	FastpathRoutePolicyStmtIpPrecedence	read-write	IP Precedence value to be remarked. This is specified through set clause in route-map statement. In order to remove configured precedence value, use invalid(8) option.
T/F fastpathRoutePolicyStmtSetIntfNull0	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.2.1.15	TruthValue	read-write	Specifying null0 as an interface in a route-map statement
fastpathRoutePolicyIfTable	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.3		not-accessible	A table of interfaces on which route-map is applied.
fastpathRoutePolicyIfEntry	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.3.1		not-accessible
NUM fastpathRoutePolicyIfIndex	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.3.1.1	InterfaceIndex	read-create	Interface to which route-map needs to be applied or Interface from which route-map needs to be removed.
STR fastpathRoutePolicyIfName	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.3.1.2	DisplayString	read-create	The name of a Route Map.
ROW fastpathRoutePolicyIfRowStatus	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.2.20.3.1.3	RowStatus	read-create	Controls creation and deletion of Row Status entries.

RFC description

Manages route policy configuration including route-map statements, permit/deny actions, and IP precedence settings for Netgear networking devices.

Start monitoring Netgear Layer 3 managed switch/router (FASTPATH-based, route policy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download NETGEAR-ROUTE-POLICY-MIB

What Is NETGEAR-ROUTE-POLICY-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description