ME1200-ERPS-MIB

All MIBs › ME1200-ERPS-MIB

Organization: Cisco Systems, Inc

Last Updated: 2014-06-23

Category: Protocol: ERPS, Vendor: Cisco

Description: Cisco ME1200 Metro Ethernet switch MIB implementing Ethernet Ring Protection Switching (ERPS/G.8032) configuration and status.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ME1200-ERPS-MIB?

ME1200-ERPS-MIB is a Cisco enterprise MIB for the ME 1200 Metro Ethernet access switch, implementing Ethernet Ring Protection Switching (ERPS, ITU-T G.8032), a Layer 2 ring-topology protection mechanism. It exposes configuration data for ring groups -- ring type, the two ring ports, interconnect/major-ring group index, virtual channel usage, and associated MEP (maintenance end point) indices for port0 signal-fail and APS (automatic protection switching) detection -- as well as capability limits like maximum groups and maximum VLANs per group. Its monitoring value centers on the software/protocol status of ring protection: confirming a ring group is correctly configured with its two ring ports and MEP associations, and, by extension, whether the ring is in a normal or protection-switched state, which is critical for detecting a ring break or failed protection switchover. It depends on the companion IEEE 802.1ag/ITU-T Y.1731 CFM MEP mechanism (referenced via the MEP index objects) for signal-fail detection. It is deployed on Cisco ME 1200 Metro Ethernet switches used in carrier-Ethernet ring topologies for access/aggregation networks. Engineers can download the ME1200-ERPS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ME1200-ERPS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco ME 1200 Metro Ethernet switch

Monitoring Examples

An operator would poll me1200ErpsConfigTable/me1200ErpsConfigEntry, checking me1200ErpsConfigRingType, me1200ErpsConfigPort0, and me1200ErpsConfigPort1 to confirm a ring group's topology is configured as expected, and cross-check me1200ErpsConfigPort0SignalFailMepIndex/me1200ErpsConfigPort0ApsMepIndex to verify the correct CFM MEPs are driving signal-fail detection and APS messaging. me1200ErpsCapabilitiesMaxGroups and me1200ErpsCapabilitiesMaxVlansPerGroup would be checked to ensure the switch is not over-provisioned relative to its supported ring capacity. A ring group missing a valid signal-fail MEP index would indicate the switch cannot properly detect a break in that ring segment.

What Can Be Monitored

ring group configuration (ports, ring type)
interconnect/major ring association
signal-fail MEP association
APS MEP association
maximum ring group/VLAN capacity

Imported Objects

From CISCOME1200-MIB

me1200SwitchMgmt

OBJECT-IDENTITY

From ME1200-TC

ME1200InterfaceIndex
ME1200RowEditorState
ME1200VlanListQuarter

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter64
Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using me1200ErpsStatisticsRapsTx OID:

Select a Cisco ME1200 Metro Ethernet switch (G.8032 ring protection switching) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type me1200ErpsStatisticsRapsTx into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the number of transmitted RAPS PDUs. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
me1200ErpsMib	1.3.6.1.4.1.9.9.815.1.72			Private MIB for Ethernet Ring Protection Switching, ERPS.
me1200ErpsMIBObjects	1.3.6.1.4.1.9.9.815.1.72.1
me1200ErpsCapabilities	1.3.6.1.4.1.9.9.815.1.72.1.1
U32 me1200ErpsCapabilitiesMaxGroups	1.3.6.1.4.1.9.9.815.1.72.1.1.1	Unsigned32	read-only	Maximum number of configured ERPS groups.
U32 me1200ErpsCapabilitiesMaxVlansPerGroup	1.3.6.1.4.1.9.9.815.1.72.1.1.2	Unsigned32	read-only	Maximum number of protected VLANS per ERPS group.
me1200ErpsConfig	1.3.6.1.4.1.9.9.815.1.72.1.2
me1200ErpsConfigTable	1.3.6.1.4.1.9.9.815.1.72.1.2.1		not-accessible	This is the ERPS group configuration table.
me1200ErpsConfigEntry	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1		not-accessible	Each entry in this table represents an ERPS group.
I32 me1200ErpsConfigGroupIndex	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.1	Integer32	not-accessible	ERPS group index number. Valid range is (1..max groups). The maximum group number is platform-specific and can be retrieved from the ERPS capabilities.
ME1 me1200ErpsConfigRingType	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.2	ME1200ErpsRingType	read-write	Type of ring. Can only be set once for a ring instance.
NUM me1200ErpsConfigPort0	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.3	ME1200InterfaceIndex	read-write	ifindex of ring protection port 0. Can only be set once for a ring instance.
NUM me1200ErpsConfigPort1	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.4	ME1200InterfaceIndex	read-write	ifindex of ring protection Port 1. For interconnected sub-rings this value must be zero. Can only be set once for a ring instance.
U32 me1200ErpsConfigInterconnectMajorRingGroupIndex	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.5	Unsigned32	read-write	For sub-ring: zero = not interconnected; > zero = index of major ring group. For major ring: zero = not interconnected; > zero = is interconnected (i.e flag-like semantics). Can only be set once for a ring instance.
T/F me1200ErpsConfigVirtualChannel	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.6	TruthValue	read-write	Whether to use a virtual channel. Can only be set once for a ring instance.
U32 me1200ErpsConfigPort0SignalFailMepIndex	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.7	Unsigned32	read-write	Index of SignalFail MEP for Port 0. Zero if not set. To clear an ERPS group's MEP association, set this to zero; it affects all MEP indices.
U32 me1200ErpsConfigPort0ApsMepIndex	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.8	Unsigned32	read-write	Index of APS MEP for Port 0. Zero if not set.
U32 me1200ErpsConfigPort1SignalFailMepIndex	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.9	Unsigned32	read-write	Index of SignalFail MEP for Port 1. Zero if not set. Must be zero for interconnected sub-rings.
U32 me1200ErpsConfigPort1ApsMepIndex	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.10	Unsigned32	read-write	Index of APS MEP for Port 1. Zero if not set. Must be zero for interconnected sub-rings with virtual channel.
U32 me1200ErpsConfigHoldOffTime	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.11	Unsigned32	read-write	Hold off time in ms. Value is rounded down to 100ms precision. Valid range is 0-10000 ms
U32 me1200ErpsConfigWaitToRestoreTime	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.12	Unsigned32	read-write	Wait-to-Restore time in ms. Valid range is 60000-720000 ms (1-12 minutes).
U32 me1200ErpsConfigGuardTime	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.13	Unsigned32	read-write	Guard time in ms. Valid range is 10-2000 ms.
ME1 me1200ErpsConfigRplMode	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.14	ME1200ErpsRplMode	read-write	Ring Protection Link mode.
ME1 me1200ErpsConfigRplPort	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.15	ME1200ErpsPort	read-write	RPL port. Only valid if the ERPS group is RPL owner or neighbour.
T/F me1200ErpsConfigRevertive	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.16	TruthValue	read-write	Revertive (true) or Non-revertive (false) mode.
ME1 me1200ErpsConfigVersion	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.17	ME1200ErpsVersion	read-write	ERPS protocol version.
T/F me1200ErpsConfigTopologyChange	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.18	TruthValue	read-write	Whether to enable Topology Change propagation; only valid for an interconnected node.
ME1 me1200ErpsConfigProtectedVlans0Kto1K	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.19	ME1200VlanListQuarter	read-write	First quarter of bit-array indicating whether a VLAN is protected by this ring instance ('1') or not ('0').
ME1 me1200ErpsConfigProtectedVlans1Kto2K	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.20	ME1200VlanListQuarter	read-write	Second quarter of bit-array indicating whether a VLAN is protected by this ring instance ('1') or not ('0').
ME1 me1200ErpsConfigProtectedVlans2Kto3K	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.21	ME1200VlanListQuarter	read-write	Third quarter of bit-array indicating whether a VLAN is protected by this ring instance ('1') or not ('0').
ME1 me1200ErpsConfigProtectedVlans3Kto4K	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.22	ME1200VlanListQuarter	read-write	Fourth quarter of bit-array indicating whether a VLAN is protected by this ring instance ('1') or not ('0').
ME1 me1200ErpsConfigAction	1.3.6.1.4.1.9.9.815.1.72.1.2.1.1.100	ME1200RowEditorState	read-write	Action
me1200ErpsConfigRowEditor	1.3.6.1.4.1.9.9.815.1.72.1.2.2
I32 me1200ErpsConfigRowEditorGroupIndex	1.3.6.1.4.1.9.9.815.1.72.1.2.2.1	Integer32	read-write	ERPS group index number. Valid range is (1..max groups). The maximum group number is platform-specific and can be retrieved from the ERPS capabilities.
ME1 me1200ErpsConfigRowEditorRingType	1.3.6.1.4.1.9.9.815.1.72.1.2.2.2	ME1200ErpsRingType	read-write	Type of ring. Can only be set once for a ring instance.
NUM me1200ErpsConfigRowEditorPort0	1.3.6.1.4.1.9.9.815.1.72.1.2.2.3	ME1200InterfaceIndex	read-write	ifindex of ring protection port 0. Can only be set once for a ring instance.
NUM me1200ErpsConfigRowEditorPort1	1.3.6.1.4.1.9.9.815.1.72.1.2.2.4	ME1200InterfaceIndex	read-write	ifindex of ring protection Port 1. For interconnected sub-rings this value must be zero. Can only be set once for a ring instance.
U32 me1200ErpsConfigRowEditorInterconnectMajorRingGroupIndex	1.3.6.1.4.1.9.9.815.1.72.1.2.2.5	Unsigned32	read-write	For sub-ring: zero = not interconnected; > zero = index of major ring group. For major ring: zero = not interconnected; > zero = is interconnected (i.e flag-like semantics). Can only be set once for a ring instance.
T/F me1200ErpsConfigRowEditorVirtualChannel	1.3.6.1.4.1.9.9.815.1.72.1.2.2.6	TruthValue	read-write	Whether to use a virtual channel. Can only be set once for a ring instance.
U32 me1200ErpsConfigRowEditorPort0SignalFailMepIndex	1.3.6.1.4.1.9.9.815.1.72.1.2.2.7	Unsigned32	read-write	Index of SignalFail MEP for Port 0. Zero if not set. To clear an ERPS group's MEP association, set this to zero; it affects all MEP indices.
U32 me1200ErpsConfigRowEditorPort0ApsMepIndex	1.3.6.1.4.1.9.9.815.1.72.1.2.2.8	Unsigned32	read-write	Index of APS MEP for Port 0. Zero if not set.
U32 me1200ErpsConfigRowEditorPort1SignalFailMepIndex	1.3.6.1.4.1.9.9.815.1.72.1.2.2.9	Unsigned32	read-write	Index of SignalFail MEP for Port 1. Zero if not set. Must be zero for interconnected sub-rings.
U32 me1200ErpsConfigRowEditorPort1ApsMepIndex	1.3.6.1.4.1.9.9.815.1.72.1.2.2.10	Unsigned32	read-write	Index of APS MEP for Port 1. Zero if not set. Must be zero for interconnected sub-rings with virtual channel.
U32 me1200ErpsConfigRowEditorHoldOffTime	1.3.6.1.4.1.9.9.815.1.72.1.2.2.11	Unsigned32	read-write	Hold off time in ms. Value is rounded down to 100ms precision. Valid range is 0-10000 ms
U32 me1200ErpsConfigRowEditorWaitToRestoreTime	1.3.6.1.4.1.9.9.815.1.72.1.2.2.12	Unsigned32	read-write	Wait-to-Restore time in ms. Valid range is 60000-720000 ms (1-12 minutes).
U32 me1200ErpsConfigRowEditorGuardTime	1.3.6.1.4.1.9.9.815.1.72.1.2.2.13	Unsigned32	read-write	Guard time in ms. Valid range is 10-2000 ms.
ME1 me1200ErpsConfigRowEditorRplMode	1.3.6.1.4.1.9.9.815.1.72.1.2.2.14	ME1200ErpsRplMode	read-write	Ring Protection Link mode.
ME1 me1200ErpsConfigRowEditorRplPort	1.3.6.1.4.1.9.9.815.1.72.1.2.2.15	ME1200ErpsPort	read-write	RPL port. Only valid if the ERPS group is RPL owner or neighbour.
T/F me1200ErpsConfigRowEditorRevertive	1.3.6.1.4.1.9.9.815.1.72.1.2.2.16	TruthValue	read-write	Revertive (true) or Non-revertive (false) mode.
ME1 me1200ErpsConfigRowEditorVersion	1.3.6.1.4.1.9.9.815.1.72.1.2.2.17	ME1200ErpsVersion	read-write	ERPS protocol version.
T/F me1200ErpsConfigRowEditorTopologyChange	1.3.6.1.4.1.9.9.815.1.72.1.2.2.18	TruthValue	read-write	Whether to enable Topology Change propagation; only valid for an interconnected node.
ME1 me1200ErpsConfigRowEditorProtectedVlans0Kto1K	1.3.6.1.4.1.9.9.815.1.72.1.2.2.19	ME1200VlanListQuarter	read-write	First quarter of bit-array indicating whether a VLAN is protected by this ring instance ('1') or not ('0').
ME1 me1200ErpsConfigRowEditorProtectedVlans1Kto2K	1.3.6.1.4.1.9.9.815.1.72.1.2.2.20	ME1200VlanListQuarter	read-write	Second quarter of bit-array indicating whether a VLAN is protected by this ring instance ('1') or not ('0').
ME1 me1200ErpsConfigRowEditorProtectedVlans2Kto3K	1.3.6.1.4.1.9.9.815.1.72.1.2.2.21	ME1200VlanListQuarter	read-write	Third quarter of bit-array indicating whether a VLAN is protected by this ring instance ('1') or not ('0').
ME1 me1200ErpsConfigRowEditorProtectedVlans3Kto4K	1.3.6.1.4.1.9.9.815.1.72.1.2.2.22	ME1200VlanListQuarter	read-write	Fourth quarter of bit-array indicating whether a VLAN is protected by this ring instance ('1') or not ('0').
ME1 me1200ErpsConfigRowEditorAction	1.3.6.1.4.1.9.9.815.1.72.1.2.2.100	ME1200RowEditorState	read-write	Action
me1200ErpsStatus	1.3.6.1.4.1.9.9.815.1.72.1.3
me1200ErpsStatusTable	1.3.6.1.4.1.9.9.815.1.72.1.3.1		not-accessible	This table contains status per EPRS group.
me1200ErpsStatusEntry	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1		not-accessible	Status.
I32 me1200ErpsStatusGroupIndex	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.1	Integer32	not-accessible	ERPS group index number. Valid range is (1..max groups). The maximum group number is platform-specific and can be retrieved from the ERPS capabilities.
T/F me1200ErpsStatusActive	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.2	TruthValue	read-only	Specifies whether ERPS group is currently active or not.
ME1 me1200ErpsStatusProtectionState	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.3	ME1200ErpsProtectionState	read-only	Specifies current ERPS group protection state.
T/F me1200ErpsStatusRplBlocked	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.4	TruthValue	read-only	Specifies whether the RPL is currently blocked or not.
U32 me1200ErpsStatusWtrRemaining	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.5	Unsigned32	read-only	Specifies the remaining wait-time before restoring ring.
ME1 me1200ErpsStatusAdminCmd	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.6	ME1200ErpsAdminCmd	read-only	Specifies the currently active administrative command.
T/F me1200ErpsStatusFopAlarm	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.7	TruthValue	read-only	Specifies whether the FailureOfProtocol alarm is currently active or not.
T/F me1200ErpsStatusTxActive	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.8	TruthValue	read-only	Specifies whether R-APS transmission is currently active.
ME1 me1200ErpsStatusTxRequestOrState	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.9	ME1200ErpsRequestState	read-only	Specifies the currently transmitted request/state. Only relevant when Tx is active.
T/F me1200ErpsStatusTxRplBlocked	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.10	TruthValue	read-only	Specifies the currently transmitted RPL Blocked flag. Only relevant when Tx is active.
T/F me1200ErpsStatusTxDoNotFlush	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.11	TruthValue	read-only	Specifies the currently transmitted Do Not Flush flag. Only relevant when Tx is active.
ME1 me1200ErpsStatusBlockedPortReference	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.12	ME1200ErpsPort	read-only	Specifies the currently transmitted Blocked Port Reference. Only relevant when Tx is active.
T/F me1200ErpsStatusPort0Blocked	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.13	TruthValue	read-only	Specifies whether ring Port 0 is blocked or not.
ME1 me1200ErpsStatusPort0State	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.14	ME1200ErpsPortState	read-only	Specifies the state of ring Port 0.
T/F me1200ErpsStatusPort0RxActive	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.15	TruthValue	read-only	Specifies if ring Port0 receives R-APS.
ME1 me1200ErpsStatusPort0RxRequestOrState	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.16	ME1200ErpsRequestState	read-only	Specifies the most recently received request/state on ring Port 0. Only relevant when Rx is active.
T/F me1200ErpsStatusPort0RxRplBlocked	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.17	TruthValue	read-only	Specifies the most recently received RPL Blocked flag on ring Port 0. Only relevant when Rx is active.
T/F me1200ErpsStatusPort0RxDoNotFlush	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.18	TruthValue	read-only	Specifies the most recently received Do Not Flush flag on ring Port 0. Only relevant when Rx is active.
ME1 me1200ErpsStatusPort0RxBlockedPortReference	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.19	ME1200ErpsPort	read-only	Specifies the most recently received Blocked Port Reference on ring Port 0. Only relevant when Rx is active.
OCT me1200ErpsStatusPort0RxNodeId	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.20	OCTET STRING	read-only	Specifies the most recently received node ID on ring Port 0. Only relevant when Rx is active.
T/F me1200ErpsStatusPort1Blocked	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.21	TruthValue	read-only	Specifies whether ring Port 1 is blocked or not.
ME1 me1200ErpsStatusPort1State	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.22	ME1200ErpsPortState	read-only	Specifies the state of ring Port 1.
T/F me1200ErpsStatusPort1RxActive	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.23	TruthValue	read-only	Specifies if ring Port1 receives R-APS.
ME1 me1200ErpsStatusPort1RxRequestOrState	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.24	ME1200ErpsRequestState	read-only	Specifies the most recently received request/state on ring Port 1. Only relevant when Rx is active.
T/F me1200ErpsStatusPort1RxRplBlocked	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.25	TruthValue	read-only	Specifies the most recently received RPL Blocked flag on ring Port 1. Only relevant when Rx is active.
T/F me1200ErpsStatusPort1RxDoNotFlush	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.26	TruthValue	read-only	Specifies the most recently received Do Not Flush flag on ring Port 1. Only relevant when Rx is active.
ME1 me1200ErpsStatusPort1RxBlockedPortReference	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.27	ME1200ErpsPort	read-only	Specifies the most recently received Blocked Port Reference on ring Port 1. Only relevant when Rx is active.
OCT me1200ErpsStatusPort1RxNodeId	1.3.6.1.4.1.9.9.815.1.72.1.3.1.1.28	OCTET STRING	read-only	Specifies the most recently received node ID on ring Port 1. Only relevant when Rx is active.
me1200ErpsStatistics	1.3.6.1.4.1.9.9.815.1.72.1.4
me1200ErpsStatisticsTable	1.3.6.1.4.1.9.9.815.1.72.1.4.1		not-accessible	This table contains statistics per EPRS group.
me1200ErpsStatisticsEntry	1.3.6.1.4.1.9.9.815.1.72.1.4.1.1		not-accessible	Various PDU and event counters.
I32 me1200ErpsStatisticsGroupIndex	1.3.6.1.4.1.9.9.815.1.72.1.4.1.1.1	Integer32	not-accessible	ERPS group index number. Valid range is (1..max groups). The maximum group number is platform-specific and can be retrieved from the ERPS capabilities.
C64 me1200ErpsStatisticsRapsTxEx	1.3.6.1.4.1.9.9.815.1.72.1.4.1.1.2	Counter64	read-only	Number of transmitted RAPS PDUs.
C64 me1200ErpsStatisticsRapsRx	1.3.6.1.4.1.9.9.815.1.72.1.4.1.1.3	Counter64	read-only	Number of received RAPS PDUs.
C64 me1200ErpsStatisticsRapsRxDrop	1.3.6.1.4.1.9.9.815.1.72.1.4.1.1.4	Counter64	read-only	Number of received RAPS PDUs that were dropped.
C64 me1200ErpsStatisticsLocalSF	1.3.6.1.4.1.9.9.815.1.72.1.4.1.1.5	Counter64	read-only	Number of local SignalFail events.
C64 me1200ErpsStatisticsLocalSFCleared	1.3.6.1.4.1.9.9.815.1.72.1.4.1.1.6	Counter64	read-only	Number of local SignalFail clear events.
C64 me1200ErpsStatisticsRemoteSF	1.3.6.1.4.1.9.9.815.1.72.1.4.1.1.7	Counter64	read-only	Number of remote SignalFail events.
C64 me1200ErpsStatisticsNR	1.3.6.1.4.1.9.9.815.1.72.1.4.1.1.8	Counter64	read-only	Number of NoRequest events.
C64 me1200ErpsStatisticsRemoteMS	1.3.6.1.4.1.9.9.815.1.72.1.4.1.1.9	Counter64	read-only	Number of remote ManualSwitch events.
C64 me1200ErpsStatisticsLocalMS	1.3.6.1.4.1.9.9.815.1.72.1.4.1.1.10	Counter64	read-only	Number of local ManualSwitch events.
C64 me1200ErpsStatisticsRemoteFS	1.3.6.1.4.1.9.9.815.1.72.1.4.1.1.11	Counter64	read-only	Number of remote ForcedSwitch events.
C64 me1200ErpsStatisticsLocalFS	1.3.6.1.4.1.9.9.815.1.72.1.4.1.1.12	Counter64	read-only	Number of local ForcedSwitch events.
C64 me1200ErpsStatisticsAdminClear	1.3.6.1.4.1.9.9.815.1.72.1.4.1.1.13	Counter64	read-only	Number of AdminClear events.
me1200ErpsControl	1.3.6.1.4.1.9.9.815.1.72.1.5
me1200ErpsControlTable	1.3.6.1.4.1.9.9.815.1.72.1.5.1		not-accessible	This is the ERPS group control table.
me1200ErpsControlEntry	1.3.6.1.4.1.9.9.815.1.72.1.5.1.1		not-accessible	Each entry in this table represents dynamic control elements an ERPS group.
I32 me1200ErpsControlGroupIndex	1.3.6.1.4.1.9.9.815.1.72.1.5.1.1.1	Integer32	not-accessible	ERPS group index number. Valid range is (1..max groups). The maximum group number is platform-specific and can be retrieved from the ERPS capabilities.
ME1 me1200ErpsControlCommand	1.3.6.1.4.1.9.9.815.1.72.1.5.1.1.2	ME1200ErpsControlCmd	read-write	Control command to execute. Always returns none when read.
ME1 me1200ErpsControlPort	1.3.6.1.4.1.9.9.815.1.72.1.5.1.1.3	ME1200ErpsPort	read-write	Ring port affected by control command. Only relevant for administrative commands. Always returns port0 when read.
me1200ErpsMIBConformance	1.3.6.1.4.1.9.9.815.1.72.2
me1200ErpsMIBCompliances	1.3.6.1.4.1.9.9.815.1.72.2.1
me1200ErpsMibCompliance	1.3.6.1.4.1.9.9.815.1.72.2.1.1			The compliance statement for the implementation.
me1200ErpsMIBGroups	1.3.6.1.4.1.9.9.815.1.72.2.2
me1200ErpsCapabilitiesInfoGroup	1.3.6.1.4.1.9.9.815.1.72.2.2.1			A collection of objects suitable for bulk operations.
me1200ErpsConfigTableInfoGroup	1.3.6.1.4.1.9.9.815.1.72.2.2.2			A collection of objects suitable for bulk operations.
me1200ErpsConfigRowEditorInfoGroup	1.3.6.1.4.1.9.9.815.1.72.2.2.3			A collection of objects suitable for bulk operations.
me1200ErpsStatusTableInfoGroup	1.3.6.1.4.1.9.9.815.1.72.2.2.4			A collection of objects suitable for bulk operations.
me1200ErpsStatisticsTableInfoGroup	1.3.6.1.4.1.9.9.815.1.72.2.2.5			A collection of objects suitable for bulk operations.
me1200ErpsControlTableInfoGroup	1.3.6.1.4.1.9.9.815.1.72.2.2.6			A collection of objects suitable for bulk operations.

RFC description

Vendor management MIB for Microsemi/Microchip ME1200 switch series; manages Ethernet Ring Protection Switching (ERPS) configuration and status.

Start monitoring Cisco ME1200 Metro Ethernet switch (G.8032 ring protection switching) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ME1200-ERPS-MIB