| OID symbolic | OID numeric | Type | Access | Description |
|---|
| luminous | 1.3.6.1.4.1.4614 | | | |
| lumADM | 1.3.6.1.4.1.4614.1 | | | |
| lumTopologyMIB | 1.3.6.1.4.1.4614.1.3 | | | The Luminous Topology MIB contains
information related to the
Luminous Ring Topology. |
| lumRingCommands | 1.3.6.1.4.1.4614.1.3.1 | | | |
| lumTopoDiscoveryGroup | 1.3.6.1.4.1.4614.1.3.1.1 | | | |
| I32 lumTopoDiscoveryRetries | 1.3.6.1.4.1.4614.1.3.1.1.1 | Integer32 | read-write | Initially set to 3. |
| I32 lumTopoNeighborInfoTimer | 1.3.6.1.4.1.4614.1.3.1.1.2 | Integer32 | read-write | The Neighbor Information Timer sets the
amount of time between periodic sends
of the neighbor information message
from each node on each egress link. |
| I32 lumTopoDiscoveryConvergenceTimer | 1.3.6.1.4.1.4614.1.3.1.1.3 | Integer32 | read-write | The topology convergence timer sets the
amount of time during which no messages
indicating a change of topology have
been received before the topology can
be considered to have converged. If the
topology convergence timer has not
reached the required value for
convergence, the topology discovery
timer is reset. |
| I32 lumTopoDiscoveryTimer | 1.3.6.1.4.1.4614.1.3.1.1.4 | Integer32 | read-write | The topology discovery timer sets the
total amount of time until the topology
convergence timer is checked. If the
topology convergence timer has not
reached the required value for
convergence, the topology discovery
timer is reset. |
| INT lumTopoDiscovery | 1.3.6.1.4.1.4614.1.3.1.1.5 | INTEGER | read-write | Setting this field to doDiscover(2) has
the effect of starting the Ring Topology
Discovery. The Retries and Timers in the
fields above in order for them to have
effect should be set before attempting
to start discovery.
Upon Discovery completion this field is
set by the SNMP Agent to either none(1)
or ,if failed to discoveryFailed(4).
stopDiscovery(3) is for the future.
Setting to discoveryFailed(4) is not
allowed by SNMP Agent.
discoveryFailed(4) can be also the
outcome of topology discovery performed
by the ring management without NMS
requesting it. |
| IP lumTopoDiscoveryFailedNode | 1.3.6.1.4.1.4614.1.3.1.1.6 | IpAddress | read-only | The node that causes the the Topology
Discovery failure.
Valid only if lumTopoDiscovery is
discoveryFailed(4). |
| INT lumRingCommand | 1.3.6.1.4.1.4614.1.3.1.2 | INTEGER | read-write | Setting this field to clearAll(2) has
the effect of clearing all
lumLinkAdminStatus (setting it to 0).
This clears all externally initiated
commands.
Setting this field to
lockoutOfProtection(3) results in all
traffic on the ring returning to
the shortest-hop available path. This
sets all LinkAdminStatus values to
16000 (standard operational link).
Setting this field to
switchToRevertiveMode(4), has the
effect of switching from non-revertive
mode to revertive mode fot the whole
ring.
commandFailed(5) cannot be set. The
lumRingCommand is set to this value
by SNMP Agent when requested command
fails. |
| INT lumRingRevertiveMode | 1.3.6.1.4.1.4614.1.3.1.3 | INTEGER | read-write | Setting this field to revertiveMode(1),
has the effect of switching from
non-revertive mode to revertive mode
for the whole ring.
Likewise setting this field to
nonRevertiveMode(2), has the effect of
switching from revertive mode to
non-revertive mode fot the whole ring. |
| I32 lumProtectionSwitchHysteresis | 1.3.6.1.4.1.4614.1.3.1.4 | Integer32 | read-only | Hysteresis factor. This factor prevents
ping-ponging in protection switching
when a link's measured status is
varying with time. Valid values are
between 5 and 100. |
| lumProtectionSwitchingTable | 1.3.6.1.4.1.4614.1.3.2 | | not-accessible | The Luminous Protection Switching Table. |
| lumProtectionSwitchingEntry | 1.3.6.1.4.1.4614.1.3.2.1 | | not-accessible | Each entry represents connection information
of current node to other nodes on the ring. |
| IP lumProtDestinationIP | 1.3.6.1.4.1.4614.1.3.2.1.1 | IpAddress | read-only | This is the address of the destination
node. |
| I32 lumProtMeasDestCost | 1.3.6.1.4.1.4614.1.3.2.1.2 | Integer32 | read-only | This is the cumulative measured cost per
destination for each egress interface of
a node. |
| I32 lumProtNonRevDestCost | 1.3.6.1.4.1.4614.1.3.2.1.3 | Integer32 | read-only | This is the non-revertive cost per
destination for each egress interface of
a node. This is used only for
non-revertive protection switching. |
| I32 lumProtMeasPrefDir | 1.3.6.1.4.1.4614.1.3.2.1.4 | Integer32 | read-only | This is the interface number corresponding
to the preferred direction for data from
this node to lumProtDestinationIP based
on measured costs. |
| I32 lumProtNonRevPrefDir | 1.3.6.1.4.1.4614.1.3.2.1.5 | Integer32 | read-only | This is the interface number corresponding
to the preferred direction for data from
this node to lumProtDestinationIP based
on non-revertive costs. |
| lumRingLinkTable | 1.3.6.1.4.1.4614.1.3.3 | | not-accessible | The Luminous Ring Topology Table. |
| lumRingLinkEntry | 1.3.6.1.4.1.4614.1.3.3.1 | | not-accessible | Each entry represents connection information
of every ingress to every ingress node on
the ring |
| IP lumLinkIngressNodeIP | 1.3.6.1.4.1.4614.1.3.3.1.1 | IpAddress | read-only | This is the address of the ingress link
node. |
| IP lumLinkEgressNodeIP | 1.3.6.1.4.1.4614.1.3.3.1.2 | IpAddress | read-only | This is the address of the egress link
node. |
| I32 lumLinkIngressInterface | 1.3.6.1.4.1.4614.1.3.3.1.3 | Integer32 | read-only | This is the interface number (slot number)
of the ring transition card connected to
the link at the ingress node. |
| I32 lumLinkEgressInterface | 1.3.6.1.4.1.4614.1.3.3.1.4 | Integer32 | read-only | This is the interface number (slot number)
of the ring transition card connected to
the link at the egress node. |
| I32 lumLinkOperStatus | 1.3.6.1.4.1.4614.1.3.3.1.5 | Integer32 | read-only | This is the latest measured operational
status of the link. It is reported from
the ring applications to the shelf manager
to the NMS. Currently, traffic congestion
is not taken into account in status
computations. A bit error rate of
a * 10 ^ (-b), where a is greater or
equal to 1 and less than 10 and has 3
significant digits, is represented to NMS
as 1000*b + 100*(10 - a). The minimum
value of lumLinkOperStatus is 1000 to
show that the link is down, and the
maximum value of lumLinkOperStatus is
16000 to show a standard operational
link. |
| I32 lumLinkNonRevStatus | 1.3.6.1.4.1.4614.1.3.3.1.6 | Integer32 | read-only | This is the minimum value of link
operational status reported since the last
Revert-To-Measured-Oper-Status command
from the NMS.
This field is used only for non-revertive
protection switching, e.g.
lumLinkNonRevStatus will differ from
lumLinkOperStatus if a link goes down and
then comes back up, since the operator
must reactivate a link under such
conditions. For revertive protection
switching, this field is equal to
lumLinkOperStatus.
This value is set by the ring applications
and reported to EMS via the shelf
manager. |
| I32 lumLinkAdminStatus | 1.3.6.1.4.1.4614.1.3.3.1.7 | Integer32 | read-write | This is the latest administrative status
of the link set by the operator. It is
reported to the ring applications via the
shelf manager.
There are several options for this field.
If the value of lumLinkAdminStatus is set
to 0 by the operator, it is ignored by
the ring applications, e.g. the ring
applications use lumLinkOperStatus and
lumLinkAdminStatus for all decision-
making. If lumLinkAdminStatus is set to
a valid lumLinkOperStatus value by
the operator, the link is considered to
have that bit error rate irrespective of
the actual lumLinkOperStatus value. It
is expected that the 'a' value of BER
need only have one significant digit
when entered by the operator. |
| I32 lumLinkSyncOperStatus | 1.3.6.1.4.1.4614.1.3.3.1.8 | Integer32 | read-only | This is a single indicator of whether a
link is an active part of a
synchronization path.
This value is set by the ring itself and
reported to NMS. |
| I32 lumLinkSyncNonRevStatus | 1.3.6.1.4.1.4614.1.3.3.1.9 | Integer32 | read-only | . |
| I32 lumLinkSyncAdminStatus | 1.3.6.1.4.1.4614.1.3.3.1.10 | Integer32 | read-write | This is the latest administrative status of
the link for synchronization set by the
operator. It is to be set by NMS. |
| lumRingThresholdTable | 1.3.6.1.4.1.4614.1.3.4 | | not-accessible | The Luminous Ring Threshold Table. |
| lumRingThresholdEntry | 1.3.6.1.4.1.4614.1.3.4.1 | | not-accessible | Each entry represents threshold values
per threshold window on the ring. |
| I32 lumRingThresholdWindow | 1.3.6.1.4.1.4614.1.3.4.1.1 | Integer32 | read-write | This is the threshold window size. |
| I32 lumRingThresholdValue | 1.3.6.1.4.1.4614.1.3.4.1.2 | Integer32 | read-write | This is the threshold value for
this window. |
| ROW lumRingThresholdStatus | 1.3.6.1.4.1.4614.1.3.4.1.3 | RowStatus | read-write | This object is used to create and
delete rows in the Threshold Table. |
