| OID symbolic | OID numeric | Type | Access | Description |
|---|
| a3Com | 1.3.6.1.4.1.43 | | | |
| lb3gh | 1.3.6.1.4.1.43.7 | | | |
| lb3ghOptFddi | 1.3.6.1.4.1.43.7.2 | | | |
| NTF lbOptSMTHoldCondition | 1.3.6.1.4.1.43.7.2.0.1 | | | Generated when fddiSMTHoldState (fddimibSMTHoldState) assumes the state holding-prm or holding-sec. This notification is a Condition in the Status Report Protocol (see 7.2.7 and 8.3). |
| NTF lbOptSMTPeerWrapCondition | 1.3.6.1.4.1.43.7.2.0.2 | | | This condition is active when fddiSMTPeerWrapFlag (fddimibSMTPeerWrapFlag) is set. This notification is a Condition in the Status Report Protocol (see 7.2.7 and 8.3). |
| NTF lbOptMACDuplicateAddressCondition | 1.3.6.1.4.1.43.7.2.0.3 | | | This condition is active when either fddiMACDA-Flag (fddimibMACDaFlag) or fddiMACUNDA-Flag (fddimibMACUnaDaFlag) is set. This event is handled as a Condition in the Status Report Protocol (see 7.2.7 and 8.3). |
| NTF lbOptMACFrameErrorCondition | 1.3.6.1.4.1.43.7.2.0.4 | | | Generated when the fddiMACFrameErrorRatio (fddimibMACFrameErrorRatio) is greater than or equal to fddiMACFrameErrorThreshold (fddimibMACFrameErrorThreshold). This event is handled as a Condition in the Status Report Protocol (see 7.2.7 and 8.3). |
| NTF lbOptMACNotCopiedCondition | 1.3.6.1.4.1.43.7.2.0.5 | | | Generated when the fddiMACNotCopiedRatio (fddimibMACNotCopiedRatio) is greater than or equal to the fddiMACNotCopiedThreshold (lbOptMACNotCopiedThreshold). This event is handled as a Condition in the Status Report Protocol (see 7.2.7 and 8.3). |
| NTF lbOptMACNeighborChangeEvent | 1.3.6.1.4.1.43.7.2.0.6 | | | Generated when a change in a MAC's upstream neighbor address or downstream neighbor address is detected. (see 7.2.7 and 8.3). |
| NTF lbOptMACPathChangeEvent | 1.3.6.1.4.1.43.7.2.0.7 | | | This event is generated when the value of the fddiMACCurrentPath (fddimibMACCurrentPath) changes. This event shall be supressed if the value changes from isolated to local or local to isolated (see 7.2.7 and 8.3). |
| NTF lbOptPORTLerCondition | 1.3.6.1.4.1.43.7.2.0.8 | | | This condition becomes active when the value of fddiPORTLer-Estimate (fddimibPORTLerEstimate) is less than or equal to fddiPORTLer-Alarm (fddimibPORTLerAlarm). This will be reported with the Status Report Frames (SRF) (see 7.2.7 and 8.3). |
| NTF lbOptPORTUndesiredConnAttemptEvent | 1.3.6.1.4.1.43.7.2.0.9 | | | Generated when an undesired connection attempt has been made (see 5.2.4, 7.2.7, and 8.3). |
| NTF lbOptPORTEBErrorCondition | 1.3.6.1.4.1.43.7.2.0.10 | | | Generated when the Elasticity Buffer Error-Ct (lbOptPORTEBErrorCt) increments. This is handled as a condition in the Status Report Protocol. It is generated when an increment occurs in the station's sampling period (see 7.2.7 and 8.3). |
| NTF lbOptPORTPathChangeEvent | 1.3.6.1.4.1.43.7.2.0.11 | | | This event is generated when the value of the fddiPORTCurrentPath (lbOptPORTCurrentPath) changes. This event shall be surpressed if the value changes from isolated to local or local to isolated (see 7.2.7 and 8.3). |
| lbOptSMT | 1.3.6.1.4.1.43.7.2.1 | | | |
| lbOptSMTTable | 1.3.6.1.4.1.43.7.2.1.1 | | not-accessible | A list of optional SMT entries. The number of entries
shall not exceed the value of snmpFddiSMTNumber. |
| lbOptSMTEntry | 1.3.6.1.4.1.43.7.2.1.1.1 | | not-accessible | An optional SMT entry containing information common to
a given optional SMT. |
| INT lbOptSMTIndex | 1.3.6.1.4.1.43.7.2.1.1.1.1 | INTEGER | read-only | A unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization. |
| OCT lbOptSMTManufacturerOUI | 1.3.6.1.4.1.43.7.2.1.1.1.2 | OCTET STRING | read-only | The three octets of manufacturer data which make
up the manufacturerOUI component. |
| OCT lbOptSMTManufacturerData | 1.3.6.1.4.1.43.7.2.1.1.1.3 | OCTET STRING | read-only | The 29 octets of manufacturer data which make up the
manufacturerData component. |
| INT lbOptSMTHoldState | 1.3.6.1.4.1.43.7.2.1.1.1.4 | INTEGER | read-only | This variable indicates the current state of the
Hold function. The value 'not-holding' is the
default and initial value. The value must be set
to 'not-holding' as part of Active_Actions and
when the conditions causing 'holding-prm' or
'holding-sec' are no longer true. The value
'holding-prm' must be set when the condition
(notTR_Flag & not RE_Flag & (PC_LS=QLS | LEM_Fail
| TNE>NS_Max | (not LS_Flag & TPC > T_Out))) is
satisfied in state PC8:ACTIVE for the A Port. The
value 'holding-sec' must be set when the condition
(notTR_Flag & not RE_Flag & (PC_LS=QLS | LEM_Fail
| TNE>NS_Max | (not LS_Flag & TPC > T_Out))) is
satisfied in state PC8:ACTIVE for the B Port. |
| INT lbOptSMTSetCount | 1.3.6.1.4.1.43.7.2.1.1.1.5 | INTEGER | read-only | This variable is composed of a count incremented
in response to a Set operation on the MIB, and the
time of the change, however only the count is
reported here (refer to ANSI SMT 8.4.1). |
| FDD lbOptSMTLastSetStationId | 1.3.6.1.4.1.43.7.2.1.1.1.6 | FddiSMTStationIdType | read-only | The Station ID of the station that effected the last
change in the FDDI MIB. |
| lbOptMAC | 1.3.6.1.4.1.43.7.2.2 | | | |
| lbOptMACBridgeFunctionTable | 1.3.6.1.4.1.43.7.2.2.1 | | not-accessible | A list of MAC bridge function entries. |
| lbOptMACBridgeFunctionEntry | 1.3.6.1.4.1.43.7.2.2.1.1 | | not-accessible | Bridge function information for a given MAC
within a given SMT. |
| INT lbOptMACBridgeFunctionSMTIndex | 1.3.6.1.4.1.43.7.2.2.1.1.1 | INTEGER | read-only | A unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization. |
| INT lbOptMACBridgeFunctionMACIndex | 1.3.6.1.4.1.43.7.2.2.1.1.2 | INTEGER | read-only | Index variable for uniquely identifying the MAC
object instances. |
| INT lbOptMACBridgeFunctions | 1.3.6.1.4.1.43.7.2.2.1.1.3 | INTEGER | read-only | Indicates the MAC's optional bridging functions.
The Value -1 is used to indicate that bridging is
not supported by this MAC.
The value is a sum. This value initially takes
the value zero, then for each function present, 2
raised to a power is added to the sum. The powers
are according to the following table:
Function Power
tb 0 -- Transparent bridging active
sr 1 -- Src routing active
srt 2 -- Src routing transparent active |
| lbOptMACTPriTable | 1.3.6.1.4.1.43.7.2.2.2 | | not-accessible | A list of MAC T-Pri entries. |
| lbOptMACTPriEntry | 1.3.6.1.4.1.43.7.2.2.2.1 | | not-accessible | A collection of T-Pri information for a given MAC within
a given SMT. |
| INT lbOptMACTPriSMTIndex | 1.3.6.1.4.1.43.7.2.2.2.1.1 | INTEGER | read-only | A unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization. |
| INT lbOptMACTPriMACIndex | 1.3.6.1.4.1.43.7.2.2.2.1.2 | INTEGER | read-only | Index variable for uniquely identifying the MAC
object instances. |
| FDD lbOptMACTPri0 | 1.3.6.1.4.1.43.7.2.2.2.1.3 | FddiTimeNano | read-only | This attribute is an unsigned twos-complement T_pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units. |
| FDD lbOptMACTPri1 | 1.3.6.1.4.1.43.7.2.2.2.1.4 | FddiTimeNano | read-only | This attribute is an unsigned twos-complement T_pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units. |
| FDD lbOptMACTPri2 | 1.3.6.1.4.1.43.7.2.2.2.1.5 | FddiTimeNano | read-only | This attribute is an unsigned twos-complement T_pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units. |
| FDD lbOptMACTPri3 | 1.3.6.1.4.1.43.7.2.2.2.1.6 | FddiTimeNano | read-only | This attribute is an unsigned twos-complement T_pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units. |
| FDD lbOptMACTPri4 | 1.3.6.1.4.1.43.7.2.2.2.1.7 | FddiTimeNano | read-only | This attribute is an unsigned twos-complement T_pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units. |
| FDD lbOptMACTPri5 | 1.3.6.1.4.1.43.7.2.2.2.1.8 | FddiTimeNano | read-only | This attribute is an unsigned twos-complement T_pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units. |
| FDD lbOptMACTPri6 | 1.3.6.1.4.1.43.7.2.2.2.1.9 | FddiTimeNano | read-only | This attribute is an unsigned twos-complement T_pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units. |
| lbOptPATH | 1.3.6.1.4.1.43.7.2.3 | | | |
| lbOptPATHRingTable | 1.3.6.1.4.1.43.7.2.3.1 | | not-accessible | A list of PATH ring entries. |
| lbOptPATHRingEntry | 1.3.6.1.4.1.43.7.2.3.1.1 | | not-accessible | Ring latency, trace status, and T-Rmode information for a
given PATH within a given SMT. |
| INT lbOptPATHRingSMTIndex | 1.3.6.1.4.1.43.7.2.3.1.1.1 | INTEGER | read-only | A unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization. |
| INT lbOptPATHRingPATHIndex | 1.3.6.1.4.1.43.7.2.3.1.1.2 | INTEGER | read-only | Index variable for uniquely identifying the
primary, secondary and local PATH object
instances. Local PATH object instances are
represented with integer values 3 to 255. |
| FDD lbOptPATHRingLatency | 1.3.6.1.4.1.43.7.2.3.1.1.3 | FddiTimeNano | read-write | Gives the total accumulated latency of the ring
associated with this path. May be measured directly
by the station or calculated by a management station.
Values of this object are reported in 1 ns units. |
| INT lbOptPATHTraceStatus | 1.3.6.1.4.1.43.7.2.3.1.1.4 | INTEGER | read-only | This attribute indicates the current trace status of
the path.
The value is a sum which represents all of the trace
status information which applies. This value initially
takes the value zero, then for each condition which
applies, 2 raised to a power is added to the sum. the
powers are according to the following table:
TraceStatus Power
traceinitiated 0
tracepropragated 1
traceterminated 2
tracetimeout 3 |
| FDD lbOptPATHT_Rmode | 1.3.6.1.4.1.43.7.2.3.1.1.5 | FddiTimeNano | read-write | Used by RMT to limit the duration of restricted dialogs on a path. This object is reported in 1 ns units. |
| lbOptPATHSbaTable | 1.3.6.1.4.1.43.7.2.3.2 | | not-accessible | A list of PATH Sba entries. |
| lbOptPATHSbaEntry | 1.3.6.1.4.1.43.7.2.3.2.1 | | not-accessible | Sba information for a given PATH within a given SMT. |
| INT lbOptPATHSbaSMTIndex | 1.3.6.1.4.1.43.7.2.3.2.1.1 | INTEGER | read-only | A unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization. |
| INT lbOptPATHSbaPATHIndex | 1.3.6.1.4.1.43.7.2.3.2.1.2 | INTEGER | read-only | Index variable for uniquely identifying the
primary, secondary and local PATH object
instances. Local PATH object instances are
represented with integer values 3 to 255. |
| INT lbOptPATHSbaPayload | 1.3.6.1.4.1.43.7.2.3.2.1.3 | INTEGER | read-write | The payload portion of the Synchronous Bandwidth
Allocation for thi path. This value represents the
maximum number of bytes of data allocated for
transmission per 125 microseconds. |
| INT lbOptPATHSbaOverhead | 1.3.6.1.4.1.43.7.2.3.2.1.4 | INTEGER | read-write | The overhead portion of the Synchronous Bandwith
Allocation for this path. This value repersents the
maximum number of bytes overhead (token capture, frame
header, etc.) used pre negotiated Target Token Rotation
Time (T_neg). |
| INT lbOptPATHSbaAvailable | 1.3.6.1.4.1.43.7.2.3.2.1.5 | INTEGER | read-write | This value is the maximum Synchronous Bandwith available
for a path in bytes per second. |
| lbOptPORT | 1.3.6.1.4.1.43.7.2.4 | | | |
| lbOptPORTTable | 1.3.6.1.4.1.43.7.2.4.1 | | not-accessible | A list of optional PORT entries. |
| lbOptPORTEntry | 1.3.6.1.4.1.43.7.2.4.1.1 | | not-accessible | MAC loop time and EB error count information for a
given PORT within a given SMT. |
| INT lbOptPORTSMTIndex | 1.3.6.1.4.1.43.7.2.4.1.1.1 | INTEGER | read-only | A unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization. |
| INT lbOptPORTIndex | 1.3.6.1.4.1.43.7.2.4.1.1.2 | INTEGER | read-only | Index variable for uniquely identifying the PORT
object instances. |
| FDD lbOptPORTMACLoopTime | 1.3.6.1.4.1.43.7.2.4.1.1.3 | FddiTimeNano | read-write | This attribute controls the value used for T_Next(9)
(see 9.4.4.2.3). This object is reported in 1 ns
units. |
| CTR lbOptPORTEBErrorCt | 1.3.6.1.4.1.43.7.2.4.1.1.4 | Counter | read-only | A count that should as closely as possible match the
times an Elasticity Buffer Error has occurred while in
active line state. |
| lbOptPORTLSTable | 1.3.6.1.4.1.43.7.2.4.2 | | not-accessible | A list of optional PORT line state entries. |
| lbOptPORTLSEntry | 1.3.6.1.4.1.43.7.2.4.2.1 | | not-accessible | Maintenance line state and PC line state information
for a given PORT within a given SMT. |
| INT lbOptPORTLSSMTIndex | 1.3.6.1.4.1.43.7.2.4.2.1.1 | INTEGER | read-only | A unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization. |
| INT lbOptPORTLSPORTIndex | 1.3.6.1.4.1.43.7.2.4.2.1.2 | INTEGER | read-only | Index variable for uniquely identifying the PORT
object instances. |
| INT lbOptPORTMaintLS | 1.3.6.1.4.1.43.7.2.4.2.1.3 | INTEGER | read-write | The PORT Maintenance Line State specifies the line state
(Maint_LS) to be transmitted when the PCM state machine
for the port is in state PC9 Maint. |
| INT lbOptPORTPCLS | 1.3.6.1.4.1.43.7.2.4.2.1.4 | INTEGER | read-only | This attribute indicates the line state (PC_LS) received
by the port. |
