LEXMARK-PVT-MIB

All MIBs › LEXMARK-PVT-MIB

Category: Printer and Finishing

Description: Lexmark private MIB for managing Lexmark printer device configuration, consumable status, and job accounting.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is LEXMARK-PVT-MIB?

LEXMARK-PVT-MIB is Lexmark's private enterprise MIB for managing Lexmark network printers, covering the underlying operating system layer of the print engine including firmware revision, memory sizing, and job/timeout handling. It exposes objects for firmware code revision, RAM/NVRAM/ROM size and type, supported protocols, current print job identification and timeout, and a per-job current-job table, along with hardware identification fields like card part number and engineering change level. Its monitoring focus spans both software and hardware status: opsysCodeRev tracks firmware version, opsysRAMSize/opsysNVRAMSize/opsysROMSize describe memory hardware, opsysCurrentJob and opsysCurrentJobTable reveal active print job state and stuck/timed-out jobs via opsysJobTimeout and opsysTimeToReset, and opsysCardPartNo/opsysCardEC identify the installed controller card hardware revision. It typically complements the standard Printer MIB (RFC 3805) rather than replacing it, adding Lexmark-specific operating-system-level detail. It is deployed on Lexmark network-attached laser/inkjet printers and multifunction devices in office environments. Engineers can download the LEXMARK-PVT-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in LEXMARK-PVT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Lexmark network laser/inkjet printer
Lexmark multifunction device

Monitoring Examples

An administrator would poll opsysCurrentJob and opsysCurrentJobTable to see which print job is active on a Lexmark printer, and check opsysJobTimeout and opsysTimeToReset to determine if a stuck job is about to be force-cleared. opsysCodeRev would be polled fleet-wide to confirm all Lexmark printers are running the expected firmware version before a support escalation. opsysRAMSize, opsysNVRAMSize, and opsysROMSize would be checked when diagnosing a printer that is failing to accept large or complex print jobs due to insufficient memory.

What Can Be Monitored

firmware/code revision
RAM/NVRAM/ROM size
current print job and job timeout
supported protocols
controller card part number/revision

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Gauge
IpAddress
enterprises

From RFC1213-MIB

DisplayString
PhysAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
lexmark	1.3.6.1.4.1.641
adapter	1.3.6.1.4.1.641.1
NTF irCleared	1.3.6.1.4.1.641.1.0.0			The condition on the printer has been cleared.
NTF irCondition	1.3.6.1.4.1.641.1.0.1			An error condition exists on the printer
NTF irOutputFull	1.3.6.1.4.1.641.1.0.2			The printers output bin is full.
NTF irLoadPaper	1.3.6.1.4.1.641.1.0.3			Load paper on the printer
NTF irPaperJam	1.3.6.1.4.1.641.1.0.4			Paper jam on the printer.
NTF irTonerLow	1.3.6.1.4.1.641.1.0.5			Toner low on the printer
NTF irServiceReq	1.3.6.1.4.1.641.1.0.6			Service required on the printer
NTF irDiskErr	1.3.6.1.4.1.641.1.0.7			Disk error on the printer
NTF irCoverOpen	1.3.6.1.4.1.641.1.0.8			Cover open on the printer
NTF irPageComplexity	1.3.6.1.4.1.641.1.0.9			Page complexity error on the printer
NTF irOffline	1.3.6.1.4.1.641.1.0.10			The printer is offline
NTF irClearedTypeII	1.3.6.1.4.1.641.1.0.11			The condition on the printer has been cleared.
opsys	1.3.6.1.4.1.641.1.1
STR opsysCodeRev	1.3.6.1.4.1.641.1.1.1	DisplayString	read-only	A textual identification of network adapter's firmware revision level. For example: 7.15.1
INT opsysJobTimeout	1.3.6.1.4.1.641.1.1.2	INTEGER	read-write	The adapter job timeout period in seconds.
STR opsysCurrentJob	1.3.6.1.4.1.641.1.1.3	DisplayString	read-only	A textual description of the currently printing job containing the Source NOS, Source server, Source user, Job number, and Job size, separated by CR LF. A NULL string indicates no active job. For multiport adapters, this reflects job status of printer port 1.
INT opsysRAMSize	1.3.6.1.4.1.641.1.1.4	INTEGER	read-only	The size of the network adapter's RAM in bytes.
INT opsysNVRAMSize	1.3.6.1.4.1.641.1.1.5	INTEGER	read-only	The size of the network adapter's NVRAM in bytes.
INT opsysROMSize	1.3.6.1.4.1.641.1.1.6	INTEGER	read-only	The size of the network adapter's ROM in bytes.
STR opsysROMType	1.3.6.1.4.1.641.1.1.7	DisplayString	read-only	A textual description of the network adapter's ROM technology. Currently valid types are: MASK_ROM, OTP, FLASH, UV_EPROM, EEPROM, and OTHER.
INT opsysProtocols	1.3.6.1.4.1.641.1.1.8	INTEGER	read-only	A bitmap representing the protocols supported by the network adapter. Bit Value Protocol --- ----- ---------- 0 1 LexLink 1 2 Netware 2 4 AppleTalk 3 8 TCP/IP 4 16 reserved 5 32 reserved 6 64 NDS
INT opsysTimeToReset	1.3.6.1.4.1.641.1.1.9	INTEGER	read-write	The amount of time remaining until the adapter performs a power on reset. A value of -1 indicates no reset is scheduled. Setting to 0 causes the adapter to reset immediately. The only valid set value is 0.
STR opsysCardPartNo	1.3.6.1.4.1.641.1.1.10	DisplayString	read-only	A textual representation of the network adapter's part number.
STR opsysCardEC	1.3.6.1.4.1.641.1.1.11	DisplayString	read-only	A textual representation of the network adapter's EC level.
opsysCurrentJobTable	1.3.6.1.4.1.641.1.1.12		not-accessible	A table of current job information for each of the network adapter's printer ports.
opsysCurrentJobEntry	1.3.6.1.4.1.641.1.1.12.1		not-accessible	An entry containing job information for one printer port.
INT opsysCurrentJobEntryIndex	1.3.6.1.4.1.641.1.1.12.1.1	INTEGER	read-only	A unique value used by the adapter to identify job information for one printer port. Each entry corresponds to a value lexhdwrPortTableIndex.
STR opsysCurrentJobString	1.3.6.1.4.1.641.1.1.12.1.2	DisplayString	read-only	A textual description of the this printer port's currently printing job containing the Source NOS, Source server, Source user, Job number, and Job size, separated by CR LF. A NULL string indicates no active job.
OCT opsysDeviceType	1.3.6.1.4.1.641.1.1.13	OCTET STRING	read-only	A two byte code representing the adapter's type.
OCT opsysAdapterName	1.3.6.1.4.1.641.1.1.14	OCTET STRING	read-only	A Unicode representation of the adapter's name.
OCT opsysAdapterCapabilities	1.3.6.1.4.1.641.1.1.15	OCTET STRING	read-only	A bitmap representing the capabilities of the adapter. Bit Value Frame type --- ---------- -------------------------- 31 0x80000000 NPANT via Netware and IP 30 0x40000000 Receive-only Fax 29 0x20000000 reserved 28 0x10000000 Adapter HTTP 27 0x08000000 Printer HTTP 26 0x04000000 HTTP Configuration Page 25 0x02000000 Copier Option
lexlink	1.3.6.1.4.1.641.1.2
INT lexlinkActivated	1.3.6.1.4.1.641.1.2.1	INTEGER	read-write	The activation status of the LexLink protocol. If this variable is changed, the adapter must be reset before the change will take effect. See opsysTimeToReset.
STR lexlinkNickname	1.3.6.1.4.1.641.1.2.2	DisplayString	read-write	The nickname assigned to the adapter for the LexLink protocol. Note that some adapters may not support the maximum length.
lexipx	1.3.6.1.4.1.641.1.3
INT lexipxActivated	1.3.6.1.4.1.641.1.3.1	INTEGER	read-write	The activation status of the Netware protocol. If this variable is changed, the adapter must be reset before the change will take effect. See opsysTimeToReset.
STR lexipxLoginName	1.3.6.1.4.1.641.1.3.2	DisplayString	read-write	The adapter's Netware login name. If this variable is changed, the adapter must be reset before the change will take effect. See opsysTimeToReset.
STR lexipxNetNumber	1.3.6.1.4.1.641.1.3.3	DisplayString	read-only	The network number of the Netware network to which the adapter is connected.
INT lexipxSAPMode	1.3.6.1.4.1.641.1.3.4	INTEGER	read-write	The network adapter's current Netware SAP'ing status.
INT lexipxServerMode	1.3.6.1.4.1.641.1.3.5	INTEGER	read-write	The current Netware server mode of the adapter. If this variable is changed, the adapter must be reset before the change will take effect. See opsysTimeToReset.
INT lexipxNumPorts	1.3.6.1.4.1.641.1.3.6	INTEGER	read-only	The number of Netware printer ports.
lexipxPortInfoTable	1.3.6.1.4.1.641.1.3.7		not-accessible	A table of Netware printer port information.
lexipxPortInfoEntry	1.3.6.1.4.1.641.1.3.7.1		not-accessible	An entry containing Netware printer port information.
INT lexipxPortInfoIndex	1.3.6.1.4.1.641.1.3.7.1.1	INTEGER	read-only	A unique value used by the adapter to identify Netware printer ports.
INT lexipxPortInfoPollIntvl	1.3.6.1.4.1.641.1.3.7.1.2	INTEGER	read-write	The Netware queue polling interval for this printer port.
INT lexipxPortInfoEnable	1.3.6.1.4.1.641.1.3.7.1.3	INTEGER	read-write	The Netware queue status of this printer port.
INT lexipxPortInfoBannerPage	1.3.6.1.4.1.641.1.3.7.1.4	INTEGER	read-only	The Netware queue banner page status for this printer port.
INT lexipxNumPrefServers	1.3.6.1.4.1.641.1.3.8	INTEGER	read-only	The maximum number of preferred Netware servers supported by this network adapter.
lexipxPrefSrvrTable	1.3.6.1.4.1.641.1.3.9		not-accessible	A table of the network adapter's preferred Netware servers.
lexipxPrefSrvrEntry	1.3.6.1.4.1.641.1.3.9.1		not-accessible	An entry containing preferred Netware server information.
INT lexipxPrefSrvrIndex	1.3.6.1.4.1.641.1.3.9.1.1	INTEGER	read-only	A unique value used by the adapter to identify preferred Netware servers.
STR lexipxPrefSrvrName	1.3.6.1.4.1.641.1.3.9.1.2	DisplayString	read-write	The name of this preferred Netware server. If this variable is changed, the adapter must be reset before the change will take effect. See opsysTimeToReset.
lexipxConnSrvrTable	1.3.6.1.4.1.641.1.3.10		not-accessible	A table of connected Netware server information.
lexipxConnSrvrEntry	1.3.6.1.4.1.641.1.3.10.1		not-accessible	An entry containing connected Netware server information.
INT lexipxConnSrvrIndex	1.3.6.1.4.1.641.1.3.10.1.1	INTEGER	read-only	A unique value used by the adapter to identify connected Netware servers.
STR lexipxConnSrvrName	1.3.6.1.4.1.641.1.3.10.1.2	DisplayString	read-only	The name of this connected Netware server.
STR lexipxConnSrvrNet	1.3.6.1.4.1.641.1.3.10.1.3	DisplayString	read-only	The Netware network number of this connected Netware server.
STR lexipxConnSrvrNode	1.3.6.1.4.1.641.1.3.10.1.4	DisplayString	read-only	The Netware node address of the connected Netware server.
INT lexipxConnSrvrConnNum	1.3.6.1.4.1.641.1.3.10.1.5	INTEGER	read-only	The connection number of the connected Netware server (pserver mode only).
INT lexipxConnSrvrConnId	1.3.6.1.4.1.641.1.3.10.1.6	INTEGER	read-only	The connection ID of the connected Netware server (rprinter mode only).
INT lexipxConnSrvrPSConnID	1.3.6.1.4.1.641.1.3.10.1.7	INTEGER	read-only	The connection ID of the connected Netware pserver (rprinter mode only).
INT lexipxFrameType	1.3.6.1.4.1.641.1.3.11	INTEGER	read-write	A bitmap of the supported IPX frame types. Bit Value Frame type --- ----- -------------------------- 0 1 Token-Ring 1 2 Token-Ring Source Routed 2 4 Token-Ring SNAP 3 8 Token-Ring SNAP Source Routed 4 16 Ethernet 802.2 5 32 Ethernet 802.3 6 64 Ethernet Type 2 7 128 Ethernet SNAP
lexipxTrapTable	1.3.6.1.4.1.641.1.3.12		not-accessible	A table of IPX trap destination configurations.
lexipxTrapEntry	1.3.6.1.4.1.641.1.3.12.1		not-accessible	An entry containing an IPX trap destination's configuration.
INT lexipxTrapIndex	1.3.6.1.4.1.641.1.3.12.1.1	INTEGER	read-only	A unique value used by the adapter to identify IPX trap destinations.
INT lexipxTrapMask	1.3.6.1.4.1.641.1.3.12.1.2	INTEGER	read-write	The trap mask for the trap destination. It is implemented as a bitmap specifying a mask of intervention required conditions for which the adapter should send trap messages. Setting a bit to 1 enables the corresponding trap. A value of 511 will cause the adapter to send traps for all intervention required conditions. The bitmap is defined below: Bit Value Condition --- ----- -------------------------- 0 1 Output hopper full 1 2 Load Paper 2 4 Paper Jam 3 8 Toner Low 4 16 Service Required 5 32 Disk Error 6 64 Cover Opened 7 128 Page Complexity Error 8 256 Offline
OCT lexipxTrapNetworkAddress	1.3.6.1.4.1.641.1.3.12.1.3	OCTET STRING	read-write	The IPX network address of the trap destination. (4 bytes)
OCT lexipxTrapNodeAddress	1.3.6.1.4.1.641.1.3.12.1.4	OCTET STRING	read-write	The IPX node address of the trap destination. (6 bytes)
INT lexipxTrapType	1.3.6.1.4.1.641.1.3.13	INTEGER	read-write	The type of SNMP over IPX traps that will be sent by the adapter. Setting this variable to multiplexed(1) configures all intervention required conditions to send an irCondition trap (specific trap number 1) and for the clearing of intervention required conditions to send an irCleared trap (specific trap number 0). Setting this variable to individual(2) causes each intervention required condition to send its corresponding trap (specific traps numbered 2 through 10) and for the clearing of intervention required conditions to cause an irClearedTypeII trap (specific trap number 11). See the Trap Definitions Group for more information. Individual(2) is the default for IPX and is necessary for NMS annotations.
INT lexipxGSQ	1.3.6.1.4.1.641.1.3.14	INTEGER	read-write	The General Service Query (GSQ) interval. This is the period in seconds that the adapter waits after a failed GSQ before attempting another as it searches for Netware servers.
lextalk	1.3.6.1.4.1.641.1.4
INT lextalkActivated	1.3.6.1.4.1.641.1.4.1	INTEGER	read-write	The activation status of the AppleTalk protocol. If this variable is changed, the adapter must be reset before the change will take effect. See opsysTimeToReset.
STR lextalkAddress	1.3.6.1.4.1.641.1.4.2	DisplayString	read-only	The AppleTalk Address of the network card. This variable is not implemented on the XLe adapters.
STR lextalkName	1.3.6.1.4.1.641.1.4.3	DisplayString	read-only	The AppleTalk name of this adapter. This variable is not implemented on the XLe adapters.
STR lextalkZone	1.3.6.1.4.1.641.1.4.4	DisplayString	read-only	The AppleTalk zone name of this adapter. This variable is not implemented on the XLe adapters.
STR lextalkType	1.3.6.1.4.1.641.1.4.5	DisplayString	read-only	The AppleTalk type of this adapter. This variable is not implemented on the XLe adapters.
lextcp	1.3.6.1.4.1.641.1.5
INT lextcpActivated	1.3.6.1.4.1.641.1.5.1	INTEGER	read-write	The activation status of the TCP/IP Protocol. If this variable is changed, the adapter must be reset before the change will take effect. See opsysTimeToReset.
INT lextcpBootpEnable	1.3.6.1.4.1.641.1.5.2	INTEGER	read-write	The status of whether or not BOOTP is attempted to determine the IP parameters. If this variable is changed, the adapter must be reset before the change will take effect. See opsysTimeToReset.
IP lextcpAddressServ	1.3.6.1.4.1.641.1.5.3	IpAddress	read-only	The IP address of the DHCP, BOOTP, or RARP server that provided the adapter's IP address.
INT lextcpNumNPAPservers	1.3.6.1.4.1.641.1.5.4	INTEGER	read-only	The maximum number of concurrent NPAP over TCP server connections.
lextcpNPAPserversTable	1.3.6.1.4.1.641.1.5.5		not-accessible	A table of NPAP over TCP server information.
lextcpNPAPserversEntry	1.3.6.1.4.1.641.1.5.5.1		not-accessible	An entry containing NPAP over TCP server information.
INT lextcpNPAPserverIndex	1.3.6.1.4.1.641.1.5.5.1.1	INTEGER	read-only	A unique value used by the adapter to identify NPAP over TCP servers.
IP lextcpNPAPserverAddress	1.3.6.1.4.1.641.1.5.5.1.2	IpAddress	read-only	The IP address of this NPAP over TCP server.
lexhttp	1.3.6.1.4.1.641.1.5.6
INT lexhttpEnable	1.3.6.1.4.1.641.1.5.6.1	INTEGER	read-write	The status of whether the adapter will enable the HTTP server. If this variable is changed, the adapter must be reset before the change will take effect. See opsysTimeToReset.
INT lexhttpNumLinks	1.3.6.1.4.1.641.1.5.6.2	INTEGER	read-only	The number of configurable HTTP links for the adapter.
INT lexhttpBytesRemaining	1.3.6.1.4.1.641.1.5.6.3	INTEGER	read-only	The number of bytes available to store HTTP link and label information.
INT lexhttpResetLinks	1.3.6.1.4.1.641.1.5.6.4	INTEGER	read-write	A control for restoring default values for HTTP link settings. Setting the variable to reset will cause all of the HTTP link settings to be reset to their default values.
lexhttpLinkTable	1.3.6.1.4.1.641.1.5.6.5		not-accessible	A table of HTTP Link settings.
lexhttpLinkTableEntry	1.3.6.1.4.1.641.1.5.6.5.1		not-accessible	An entry containing HTTP link settings.
INT lexhttpLinkTableIndex	1.3.6.1.4.1.641.1.5.6.5.1.1	INTEGER	read-only	A unique value used by the adapter to identify HTTP link settings.
INT lexhttpLinkTableStatus	1.3.6.1.4.1.641.1.5.6.5.1.2	INTEGER	read-write	The status of the HTTP link. Get operation: linkOff -- Server will not display the link personalOn -- Server will display the custom link useDefault -- Write-only defaultOff -- Reserved defaultOn -- Server will display the default link eraseCustom -- Write-only Set operation: linkOff -- Puts the link in linkOff status customOn -- Puts the link in customOn status useDefault -- Clears the Label and URL for this link and puts the . link in defaultOn status defaultOff -- Read-only defaultOn -- Read-only eraseCustom -- Clears the Label and URL for this link and puts the . link in linkOff status
STR lexhttpLinkTableLabel	1.3.6.1.4.1.641.1.5.6.5.1.3	DisplayString	read-write	The text to be displayed as the label of this HTTP link. It may be set to define a custom link. Note that when read, this always reflects what the server would display. As such, if the status of this link is defaultOn, it will not return your custom label if read even though it has been stored. Setting the status for this link to customOn will activate your custom link label. Remember that setting the status of this link to eraseCustom or useDefault clears this variable.
STR lexhttpLinkTableURL	1.3.6.1.4.1.641.1.5.6.5.1.4	DisplayString	read-write	The URL to be hyperlinked to by the HTTP link. It may be set to define a custom link. Note that when read, this always reflects what the server would use. As such, if the status of this link is defaultOn, it will not return your custom URL if read even though it has been stored. Setting the status for this link to customOn will activate your custom link URL. Remember that setting the status of this link to eraseCustom or useDefault clears this variable.
INT lexhttpConfigEnable	1.3.6.1.4.1.641.1.5.6.6	INTEGER	read-write	The status of whether HTTP configuration page is enabled.
lexdhcp	1.3.6.1.4.1.641.1.5.7
INT lexdhcpDhcpEnable	1.3.6.1.4.1.641.1.5.7.1	INTEGER	read-write	The status of whether DHCP is enabled.
INT lexdhcpRarpEnable	1.3.6.1.4.1.641.1.5.7.2	INTEGER	read-write	The status of whether RARP is enabled.
INT lexdhcpAddressSource	1.3.6.1.4.1.641.1.5.7.3	INTEGER	read-only	The method by which the current IP parameters were obtained.
INT lexdhcpWinsStatus	1.3.6.1.4.1.641.1.5.7.4	INTEGER	read-only	The adapter's WINS server registration status.
IP lexdhcpWinsServer	1.3.6.1.4.1.641.1.5.7.5	IpAddress	read-only	The IP address of the WINS server.
STR lexdhcpHostname	1.3.6.1.4.1.641.1.5.7.6	DisplayString	read-write	The adapter's TCP/IP hostname.
INT lexdhcpLeaseLength	1.3.6.1.4.1.641.1.5.7.7	INTEGER	read-only	The length of the adapter's DHCP address lease in seconds.
INT lexdhcpTimetoExpire	1.3.6.1.4.1.641.1.5.7.8	INTEGER	read-only	The number of seconds until the DHCP address lease expires.
IP lexdhcpDNSServer	1.3.6.1.4.1.641.1.5.7.9	IpAddress	read-write	The IP address of the DNS server.
lexhdwr	1.3.6.1.4.1.641.1.6
INT lexhdwrNumPorts	1.3.6.1.4.1.641.1.6.1	INTEGER	read-only	The number of printer ports supported by this network adapter.
lexhdwrPortTable	1.3.6.1.4.1.641.1.6.2		not-accessible	A table of the adapter's printer port hardware settings.
lexhdwrPortTableEntry	1.3.6.1.4.1.641.1.6.2.1		not-accessible	An entry containing printer port hardware settings.
INT lexhdwrPortTableIndex	1.3.6.1.4.1.641.1.6.2.1.1	INTEGER	read-only	A unique value used by the adapter to identify printer ports.
INT lexhdwrPortTableType	1.3.6.1.4.1.641.1.6.2.1.2	INTEGER	read-only	The type of attachment for this printer port.
INT lexhdwrPortTableParm1	1.3.6.1.4.1.641.1.6.2.1.3	INTEGER	read-write	For serial and parallel ports, this is the port timeout in seconds. For internal ports, this parameter is unused.
INT lexhdwrPortTableParm2	1.3.6.1.4.1.641.1.6.2.1.4	INTEGER	read-write	For serial ports, this is the baud rate in bits per second. For parallel ports, this is the port mode and is defined as follows: standard(0), enhanced(1) For internal ports, this parameter is unused.
INT lexhdwrPortTableParm3	1.3.6.1.4.1.641.1.6.2.1.5	INTEGER	read-write	For serial ports, this is the parity and is defined as follows: none(0), odd(1), even(2), space(3), mark(4) For parallel and internal ports, this parameter is unused.
INT lexhdwrPortTableParm4	1.3.6.1.4.1.641.1.6.2.1.6	INTEGER	read-write	For serial ports, this is the number of data bits. For parallel and internal ports, this parameter is unused.
INT lexhdwrPortTableParm5	1.3.6.1.4.1.641.1.6.2.1.7	INTEGER	read-write	For serial ports, this is the number of stop bits and is defined as follows: bitsOne(2), bitsOneAndHalf(3), bitsTwo(4) For parallel and internal ports, this parameter is unused.
INT lexhdwrPortTableParm6	1.3.6.1.4.1.641.1.6.2.1.8	INTEGER	read-write	For serial ports, this is the pacing mode and is defined as follows: paceDtr(0), paceXonXff(1) For non XLe parallel ports, this is the parallel protocol and is defined as follows: auto(2), ecp(3), byte(4), nibble(5), compatible(6) For internal ports, and XLe parallel ports this parameter is unused.
INT lexhdwrPortTableParm7	1.3.6.1.4.1.641.1.6.2.1.9	INTEGER	read-write	For all ports, this is the configured NPAP mode.
INT lexhdwrPortTableParm8	1.3.6.1.4.1.641.1.6.2.1.10	INTEGER	read-only	For all ports, this is the NPAP status.
INT lexhdwrPortTableParm9	1.3.6.1.4.1.641.1.6.2.1.11	INTEGER	read-write	For serial ports, this is the class of device attached. This variable is unused on the XLe adapters.
lexmac	1.3.6.1.4.1.641.1.7
STR lexmacType	1.3.6.1.4.1.641.1.7.1	DisplayString	read-only	A textual representation of network medium to which the network adapter is attached (e.g. Ethernet).
GAU lexmacSpeed	1.3.6.1.4.1.641.1.7.2	Gauge	read-only	The speed, in bits per second, of the network medium to which the network adapter is attached.
INT lexmacConnType	1.3.6.1.4.1.641.1.7.3	INTEGER	read-only	The connection type by which the network adapter is connected to the network medium.
PHY lexmacUAA	1.3.6.1.4.1.641.1.7.4	PhysAddress	read-only	The network adapter's universally administered network address.
PHY lexmacLAA	1.3.6.1.4.1.641.1.7.5	PhysAddress	read-only	The network adapter's locally administered network address. A value of all zeros indicates that the LAA is not in use.
lextrap	1.3.6.1.4.1.641.1.8
INT lextrapDestNum	1.3.6.1.4.1.641.1.8.1	INTEGER	read-only	The maximum number of IP trap destinations supported by this network adapter.
lextrapDestTable	1.3.6.1.4.1.641.1.8.2		not-accessible	A table of IP trap destination configurations.
lextrapDestEntry	1.3.6.1.4.1.641.1.8.2.1		not-accessible	An entry containing an IP trap destination configuration.
INT lextrapDestIndex	1.3.6.1.4.1.641.1.8.2.1.1	INTEGER	read-only	A unique value used by the adapter to identify IP trap destinations.
IP lextrapDestIPAddr	1.3.6.1.4.1.641.1.8.2.1.2	IpAddress	read-write	The IP address of the trap destination.
INT lextrapDestMask	1.3.6.1.4.1.641.1.8.2.1.3	INTEGER	read-write	The trap mask for the trap destination. It is implemented as a bitmap specifying a mask of intervention required conditions for which the adapter should send trap messages. Setting a bit to 1 enables the corresponding trap. A value of 1023 will cause the adapter to send traps for all intervention required conditions. The bitmap is defined below: Bit Value Condition --- ----- -------------------------- 0 1 Output hopper full 1 2 Load Paper 2 4 Paper Jam 3 8 Toner Low 4 16 Service Required 5 32 Disk Error 6 64 Cover Opened 7 128 Page Complexity Error 8 256 Offline 9 512 Printer MIB (RFC 1759)
INT lextrapIPTrapType	1.3.6.1.4.1.641.1.8.3	INTEGER	read-write	The type of SNMP over IP traps that will be sent by the adapter. Setting this variable to multiplexed(1) configures all intervention required conditions to send an irCondition trap (specific trap number 1) and for the clearing of intervention required conditions to send an irCleared trap (specific trap number 0). Setting this variable to individual(2) causes each intervention required condition to send its corresponding trap (specific traps numbered 2 through 10) and for the clearing of intervention required conditions to cause an irClearedTypeII trap (specific trap number 11). See the Trap Definitions Group for more information. Type 1 is the default for IP.
time	1.3.6.1.4.1.641.1.9
INT timeReset	1.3.6.1.4.1.641.1.9.1	INTEGER	read-write	A control for initiating an update of the system time and date using the specified timeSource. Setting the variable to reset will cause the system to update it's time and date using the specified time source. See timeSource.
INT timeSource	1.3.6.1.4.1.641.1.9.2	INTEGER	read-write	The source for setting the system time and date. If this variable is changed, the time must be reset before the change will have an effect. See timeReset.
INT timeUTCOffset	1.3.6.1.4.1.641.1.9.3	INTEGER	read-write	The offset in minutes from UTC (formerly GMT) of local time. Use a negative value if West of UTC. Use a positive value if East of UTC.
INT timeDSTEnable	1.3.6.1.4.1.641.1.9.4	INTEGER	read-write	The status of whether automatic Daylight Savings Time adjust is enabled. See timeDSTStartDate, timeDSTEndDate, and timeDSTOffset for configuration options.
OCT timeDSTStartDate	1.3.6.1.4.1.641.1.9.5	OCTET STRING	read-write	A textual representation of the day and time the Daylight Savings Time adjust should start if enabled (see timeDSTEnable). The format of string is as follows: Byte Meaning ---- ------------------------------------------------------------ 0 Which occurence in the month of the day specified in byte 1. Valid values are: F => First Occurence 1 => First Occurence 2 => Second Occurence 3 => Third Occurence 4 => Fourth Occurence 5 => Fifth Occurence L => Last Occurence 1 A 1-digit field indicating the day of week (0=Sun..6=Sat) 2-3 A 2-digit field indicating the month. 4-5 A 2-digit field indicating the hour 6-7 A 2-digit field indicating the minute 8-9 A 2-digit field indicating the second The default setting is F004020000 which corresponds to the first Sunday of April at 2:00:00 am.
OCT timeDSTEndDate	1.3.6.1.4.1.641.1.9.6	OCTET STRING	read-write	A textual representation of the day and time the Daylight Savings Time adjust should end if enabled (see timeDSTEnable). The format of string is as defined for timeDSTStartDate The default setting is L010020000 which corresponds to the last Sunday of October at 2:00:00 am.
INT timeDSTOffset	1.3.6.1.4.1.641.1.9.7	INTEGER	read-write	The offset in minutes that should be applied to local time during Daylight Savings Time.
IP timeServerAddress	1.3.6.1.4.1.641.1.9.8	IpAddress	read-write	If the specified time source is NTP (see timeSource), this is the IP address of the NTP server to use. Otherwise, the value is ignored.
STR timeServerName	1.3.6.1.4.1.641.1.9.9	DisplayString	read-write	If the specified time source is NTP (see timeSource), and the NTP server address is not set (0.0.0.0), this is the DNS domainname of the NTP server. If the specified time source is Netware (see timeSource), the is the name of Netware server. Otherwise, the value is ignored.
printer	1.3.6.1.4.1.641.2
prtgen	1.3.6.1.4.1.641.2.1
INT prtgenNumber	1.3.6.1.4.1.641.2.1.1	INTEGER	read-only	The number of printers, regardless of their current state, available to this adapter.
prtgenInfoTable	1.3.6.1.4.1.641.2.1.2		not-accessible	A table of the network adapter's attached printer information.
prtgenInfoEntry	1.3.6.1.4.1.641.2.1.2.1		not-accessible	An entry containing attached printer information.
INT prtgenPrinterIndex	1.3.6.1.4.1.641.2.1.2.1.1	INTEGER	read-only	A unique value used by the network adapter to identify attached printers.
STR prtgenPrinterName	1.3.6.1.4.1.641.2.1.2.1.2	DisplayString	read-only	A textual description of the make and model of the attached printer, if known.
STR prtgenPeripheralID	1.3.6.1.4.1.641.2.1.2.1.3	DisplayString	read-only	A textual description of the peripheral ID of the attached printer as defined by the IEEE 1284 standard, if known.
STR prtgenCodeRevision	1.3.6.1.4.1.641.2.1.2.1.4	DisplayString	read-only	A textual representation of the code revision level of the attached printer, if known.
INT prtgenResValue	1.3.6.1.4.1.641.2.1.2.1.5	INTEGER	read-only	This object is currently unused and reserved.
STR prtgenSerialNo	1.3.6.1.4.1.641.2.1.2.1.6	DisplayString	read-only	A textual representation of the serial number of the attached printer, if known.
prtgenStatusTable	1.3.6.1.4.1.641.2.1.3		not-accessible	A table of the network adapter's attached printer status.
prtgenStatusEntry	1.3.6.1.4.1.641.2.1.3.1		not-accessible	An entry containing attached printer status.
INT prtgenStatPrinterIndex	1.3.6.1.4.1.641.2.1.3.1.1	INTEGER	read-only	A unique value used by the network adapter to identify attached printers.
INT prtgenStatusIRC	1.3.6.1.4.1.641.2.1.3.1.2	INTEGER	read-only	The printer's current intervention required code.
INT prtgenStatusOutHopFull	1.3.6.1.4.1.641.2.1.3.1.3	INTEGER	read-only	The printer's current output hopper status.
INT prtgenStatusInputEmpty	1.3.6.1.4.1.641.2.1.3.1.4	INTEGER	read-only	The printer's current active input paper tray status.
INT prtgenStatusPaperJam	1.3.6.1.4.1.641.2.1.3.1.5	INTEGER	read-only	The printer's current paper path status.
INT prtgenStatusTonerError	1.3.6.1.4.1.641.2.1.3.1.6	INTEGER	read-only	The printer's current toner supply status.
INT prtgenStatusSrvcReqd	1.3.6.1.4.1.641.2.1.3.1.7	INTEGER	read-only	The printer's current service required status.
INT prtgenStatusDiskError	1.3.6.1.4.1.641.2.1.3.1.8	INTEGER	read-only	The printer's current disk sub-system status.
INT prtgenStatusCoverOpen	1.3.6.1.4.1.641.2.1.3.1.9	INTEGER	read-only	The printer's current cover status.
INT prtgenStatusPageComplex	1.3.6.1.4.1.641.2.1.3.1.10	INTEGER	read-only	The printer's current complex page status.
INT prtgenStatusLineStatus	1.3.6.1.4.1.641.2.1.3.1.11	INTEGER	read-only	The printer's current online/offline status.
INT prtgenStatusBusy	1.3.6.1.4.1.641.2.1.3.1.12	INTEGER	read-only	The printer's current bust status.
INT prtgenStatusWaiting	1.3.6.1.4.1.641.2.1.3.1.13	INTEGER	read-only	The printer's current waiting status.
INT prtgenStatusWarming	1.3.6.1.4.1.641.2.1.3.1.14	INTEGER	read-only	The printer's current warming status.
INT prtgenStatusPrinting	1.3.6.1.4.1.641.2.1.3.1.15	INTEGER	read-only	The printer's current printing status.
attachment	1.3.6.1.4.1.641.3
fax	1.3.6.1.4.1.641.3.1
INT faxNumber	1.3.6.1.4.1.641.3.1.1	INTEGER	read-only	The number of fax modems attached to the adapter.
faxTable	1.3.6.1.4.1.641.3.1.2		not-accessible	A table of the network adapter's attached fax modems configuration data.
faxEntry	1.3.6.1.4.1.641.3.1.2.1		not-accessible	An entry containing attached fax modem configuration data.
INT faxIndex	1.3.6.1.4.1.641.3.1.2.1.1	INTEGER	read-only	A unique value used by the adapter to identify fax ports.
INT faxPort	1.3.6.1.4.1.641.3.1.2.1.2	INTEGER	read-only	The network adapter's port to which this modem is attached.
INT faxAdapterCapabilities	1.3.6.1.4.1.641.3.1.2.1.3	INTEGER	read-only	A bitmap representing the fax capabilities of the network adapter. Bit Value Capabilities --- ------ -------------------- 0 1 Fine Resolution 1 2 2D Encoding 2 4 T6 Encoding 3 8 ECM 4 16 Binary File Transfer 5 32 300 x 300 6 64 400 x 400 7 128 200 x 400 8 256 Uncompressed Mode 9 512 255mm Width 10 1024 303mm Width 11 2048 Legal Length 12 4096 Unlimited Length 13 8192 V.17 (14400) 14 16384 V.33 (14400) 15 32768 V.29 and V.27 (9600) 16 65536 V.29 (9600) 17 131072 V.27 (4800) 18 262144 V27 (2400)
INT faxModemCapabilities	1.3.6.1.4.1.641.3.1.2.1.4	INTEGER	read-only	A bitmap representing the fax capabilities of the attached modem. Bit Value Capabilities --- ------ -------------------- 0 1 Fine Resolution 1 2 2D Encoding 2 4 T6 Encoding 3 8 ECM 4 16 Binary File Transfer 5 32 300 x 300 6 64 400 x 400 7 128 200 x 400 8 256 Uncompressed Mode 9 512 255mm Width 10 1024 303mm Width 11 2048 Legal Length 12 4096 Unlimited Length 13 8192 V.17 (14400) 14 16384 V.33 (14400) 15 32768 V.29 and V.27 (9600) 16 65536 V.29 (9600) 17 131072 V.27 (4800) 18 262144 V27 (2400)
INT faxSelectedCapabilities	1.3.6.1.4.1.641.3.1.2.1.5	INTEGER	read-write	A bitmap representing the user selected fax capabilities. Bit Value Capabilities --- ------ -------------------- 0 1 Fine Resolution 1 2 2D Encoding 2 4 T6 Encoding 3 8 ECM 4 16 Binary File Transfer 5 32 300 x 300 6 64 400 x 400 7 128 200 x 400 8 256 Uncompressed Mode 9 512 255mm Width 10 1024 303mm Width 11 2048 Legal Length 12 4096 Unlimited Length 13 8192 V.17 (14400) 14 16384 V.33 (14400) 15 32768 V.29 and V.27 (9600) 16 65536 V.29 (9600) 17 131072 V.27 (4800) 18 262144 V27 (2400)
INT faxActiveCapabilities	1.3.6.1.4.1.641.3.1.2.1.6	INTEGER	read-only	A bitmap representing the active fax capabilities. This is the logical and of faxAdapterCapabilities, faxModemCapabilities, and faxSelectedCapabilities. Bit Value Capabilities --- ------ -------------------- 0 1 Fine Resolution 1 2 2D Encoding 2 4 T6 Encoding 3 8 ECM 4 16 Binary File Transfer 5 32 300 x 300 6 64 400 x 400 7 128 200 x 400 8 256 Uncompressed Mode 9 512 255mm Width 10 1024 303mm Width 11 2048 Legal Length 12 4096 Unlimited Length 13 8192 V.17 (14400) 14 16384 V.33 (14400) 15 32768 V.29 and V.27 (9600) 16 65536 V.29 (9600) 17 131072 V.27 (4800) 18 262144 V27 (2400)
STR faxIDString	1.3.6.1.4.1.641.3.1.2.1.7	DisplayString	read-write	The textual identification that is used to identify this fax device. This text is sent to a connected fax device at the start of a call.
STR faxInitString	1.3.6.1.4.1.641.3.1.2.1.8	DisplayString	read-write	The commands used be the network adapter to initialize an attached modem.
INT faxNumberRings	1.3.6.1.4.1.641.3.1.2.1.9	INTEGER	read-write	The number of rings that the network adapter should wait before answering.
INT faxScaling	1.3.6.1.4.1.641.3.1.2.1.10	INTEGER	read-write	The mechanism used to resolve size descrepancies between the received fax the printer's available forms.
INT faxBinaryEncoding	1.3.6.1.4.1.641.3.1.2.1.11	INTEGER	read-write	The encoding used when sending fax data to the attached printer.
INT faxPrinterPort	1.3.6.1.4.1.641.3.1.2.1.13	INTEGER	read-write	The port (printer) to which received faxes should be printed.
INT faxInputTray	1.3.6.1.4.1.641.3.1.2.1.14	INTEGER	read-write	The input tray from which received faxes should be printed. The value 255 indicates printer default.
INT faxOutputBin	1.3.6.1.4.1.641.3.1.2.1.15	INTEGER	read-write	The output bin to which received faxes should be printed. The value 255 indicates printer default.

RFC description

Private MIB for Lexmark printers and network adapters covering firmware, job management, and hardware configuration.

Start monitoring Lexmark network laser/inkjet printer or multifunction device with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download LEXMARK-PVT-MIB

What Is LEXMARK-PVT-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description