Juniper-RADIUS-CLIENT-MIB

All MIBs › Juniper-RADIUS-CLIENT-MIB

Organization: Juniper Networks, Inc.

Last Updated: 2009-02-26

Category: Protocol: RADIUS, RADIUS and AAA, Vendor: Juniper

Description: Juniper Networks MIB for managing RADIUS authentication and accounting client configuration on Juniper E-series routers.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Juniper-RADIUS-CLIENT-MIB?

Juniper-RADIUS-CLIENT-MIB is a Juniper Networks proprietary MIB targeting Juniper's E-series (ERX) edge routers, covering configuration of the router's RADIUS client used for subscriber and session authentication and accounting. It exposes objects for RADIUS client identity and algorithm settings, source address and UDP checksum behavior, NAS (Network Access Server) identifier and port-naming formats, DSL/Ethernet port-type encoding for RADIUS attributes, and accounting session-ID formatting. Its management value is verifying AAA client configuration correctness rather than hardware health — operators use it to confirm the RADIUS client is using the intended source address, NAS identifier conventions, and accounting formats expected by the upstream RADIUS server, which is critical for correct subscriber billing and session tracking on broadband access networks. It is directly built on the IETF RADIUS protocol (RFC 2865/2866) standards for authentication and accounting. It is deployed on Juniper E-series broadband edge routers in ISP/carrier networks providing DSL or Ethernet subscriber access with centralized RADIUS-based AAA. Engineers can download the Juniper-RADIUS-CLIENT-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Juniper-RADIUS-CLIENT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Juniper Networks E-series (ERX) edge routers

Monitoring Examples

An operator would check juniRadiusClientSourceAddress and juniRadiusClientNasIdentifier to confirm the router is presenting the correct source IP and NAS identity to the RADIUS server, and verify juniRadiusClientAcctSessionIdFormat and juniRadiusClientNasPortFormat match what the billing system expects to correctly parse session records. If subscriber accounting records were being rejected or mis-billed, checking juniRadiusClientDslPortType or juniRadiusClientEthernetPortType against the access technology in use, and juniRadiusClientIncludeIpAddrInAcctStart, would help diagnose a RADIUS attribute-formatting mismatch.

What Can Be Monitored

RADIUS client source address/algorithm
NAS identifier and port-naming format
accounting session-ID format
DSL/Ethernet port-type encoding

Imported Objects

From Juniper-MIBs

juniMibs

MODULE-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using juniRadiusAuthClientInvalidServerAddresses OID:

Select a Juniper Networks E-series (ERX) edge router (RADIUS client configuration) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type juniRadiusAuthClientInvalidServerAddresses into the Find box to locate it in the OID tree, then select it and click OK. The number of RADIUS Access-Response packets received from unknown addresses. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
juniRadiusClientMIB	1.3.6.1.4.1.4874.2.2.19			The Remote Authentication Dial In User Service (RADIUS) Client MIB for the Juniper enterprise.
juniRadiusClientObjects	1.3.6.1.4.1.4874.2.2.19.1
juniRadiusGeneralClient	1.3.6.1.4.1.4874.2.2.19.1.1
STR juniRadiusClientIdentifier	1.3.6.1.4.1.4874.2.2.19.1.1.1	DisplayString	read-only	The NAS-Identifier of the RADIUS client.
INT juniRadiusClientAlgorithm	1.3.6.1.4.1.4874.2.2.19.1.1.2	INTEGER	read-write	The algorithm used by the client when multiple authentication/accounting servers are configured: direct Use servers in order of precedence, each time beginning with the highest precedence server and proceeding to lower precedence servers if the the RADIUS request fails, until the request succeeds or all servers have been tried. roundRobin Use servers in round-robin order, each time beginning with the next round-robin-ordered server and proceeding cyclically through servers if the RADIUS request fails, until the request succeeds or all servers have been tried.
IP juniRadiusClientSourceAddress	1.3.6.1.4.1.4874.2.2.19.1.1.3	IpAddress	read-write	The source address used by the RADIUS client in requests to the RADIUS server. The RADIUS server returns responses from this address. Setting this object to 0.0.0.0 will reset the value to its default.
T/F juniRadiusClientUdpChecksum	1.3.6.1.4.1.4874.2.2.19.1.1.4	TruthValue	read-write	Enables/disables the checksum calculations on RADIUS UDP packets.
STR juniRadiusClientNasIdentifier	1.3.6.1.4.1.4874.2.2.19.1.1.5	DisplayString	read-write	The identifier used by the client for the value of NAS-Identifier attribute (number 32) in access and accounting requests. The default is to use the system name.
INT juniRadiusClientDslPortType	1.3.6.1.4.1.4874.2.2.19.1.1.6	INTEGER	read-write	The value to use in the NAS-Port-Type RADIUS Attribute (attribute number 61) for DSL interfaces in the RADIUS access and accounting messages: virtual Used for Virtual interfaces. sdsl Used for Symmetric DSL. adsl-cap Used for Asymmetric DSL, Carrierless Amplitude Phase Modulation. adsl-dmt Used for Asymmetric DSL, Discrete Multi-Tone. idsl Used for ISDN Digital Subscriber Line. xdsl Used for Digital Subscriber Line of unknown type.
T/F juniRadiusClientTunnelAccounting	1.3.6.1.4.1.4874.2.2.19.1.1.7	TruthValue	read-write	Enables/disables the tunnel accounting feature, which causes the system to send tunnel and session accounting requests.
INT juniRadiusClientAcctSessionIdFormat	1.3.6.1.4.1.4874.2.2.19.1.1.8	INTEGER	read-write	The format used by the client for the Acct-Session-ID attribute (attribute number 44): decimal Use an ASCII decimal value only in the Acct-Session-ID attribute. description Use an ASCII description value which includes the interface type (i.e. ATM), slot, port, and circuit number (VPI and VCI for ATM), and a hexidecimal value in the Acct-Session-ID attribute.
INT juniRadiusClientNasPortFormat	1.3.6.1.4.1.4874.2.2.19.1.1.9	INTEGER	read-write	The format used by the client for the NAS-Port attribute (attribute number 5): xssssppp In the NAS-Port attribute (attribute 5) use format of 0 bit, followed by 4 bits for the slot number, 3 bits for the port number, and finally, the circuit number in the remaining bits. ssssxppp In the NAS-Port attribute (attribute 5) use format of 4 bits for the slot number, followed by a 0 bit, 3 bits for the port number and finally, the circuit number in the remaining bits.
STR juniRadiusClientCallingStationDelimiter	1.3.6.1.4.1.4874.2.2.19.1.1.10	DisplayString	read-write	The character use as for delimiting fields in the Calling-Station-ID attribute (attribute 31, from RFC 2865) sent by the client. The default value is '#'.
INT juniRadiusClientEthernetPortType	1.3.6.1.4.1.4874.2.2.19.1.1.11	INTEGER	read-write	The value to use in the NAS-Port-Type RADIUS Attribute (attribute number 61) for Ethernet interfaces in the RADIUS access and accounting messages: ethernet Used for Ethernet interfaces. virtual Used for Virtual interfaces.
T/F juniRadiusClientIncludeIpAddrInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.12	TruthValue	read-write	Enables/disables the inclusion of the Framed-IP-Address attribute in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeAcctSessionIdInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.13	TruthValue	read-write	Enables/disables the inclusion of the Acct-Session-ID attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientRollover	1.3.6.1.4.1.4874.2.2.19.1.1.14	TruthValue	read-write	Enables/disables the rollover to next server on receipt of access-reject.
INT juniRadiusClientCallingStationIdFormat	1.3.6.1.4.1.4874.2.2.19.1.1.15	INTEGER	read-write	The format used by the client for the Calling-Station-ID attribute (attribute number 31): delimited In the Calling-Station-ID attribute (attribute 31) use the format ' '. fixedFomat In the Calling-Station-ID attribute (attribute 31) use the format of 4 bytes for the host name (truncated if needed), 2 digits of slot, 1 digit of port, 3 digits of VPI, followed by 5 digits of VCI. fixedFormatAdapterEmbedded In the Calling-Station-ID attribute (attribute 31) use the format of 4 bytes for the host name (truncated if needed), 1 digit of slot, 1 digit of adapter, 1 digit of port, 3 digits of VPI, followed by 5 digits of VCI. fixedFormatAdapterNewField In the Calling-Station-ID attribute (attribute 31) use the format of 4 bytes for the host name (truncated if needed), 2 digits of slot, 1 digit of adapter, 2 digits of port, 3 digits of VPI, followed by 5 digits of VCI. fixedFormatStacked In the Calling-Station-ID attribute (attribute 31) use the format of 4 bytes for the host name (truncated if needed), 2 digits of slot, 1 digit of port, 4 digits of SVLAN ID and 4 digits of VLAN ID only in the case of Ethernet fixedFormatAdapterEmbeddedStacked In the Calling-Station-ID attribute (attribute 31) use the format of 4 bytes for the host name (truncated if needed), 1 digit of slot, 1 digit of adapter, 1 digit of port, 4 digits of SVLAN ID and 4 digits of VLAN ID only in the case of Ethernet fixedFormatAdapterNewFieldStacked In the Calling-Station-ID attribute (attribute 31) use the format of 4 bytes for the host name (truncated if needed), 2 digits of slot, 1 digit of adapter, 2 digits of port, 4 digits of SVLAN ID and 4 digits of VLAN ID only in the case of Ethernet
INT juniRadiusClientNasIpAddrUse	1.3.6.1.4.1.4874.2.2.19.1.1.16	INTEGER	read-write	The value used by the client for the NAS-IP-Addr attribute (attribute number 4): normal Use the ERX IP address value in the NAS-IP-Addr attribute (attribute 4). tunnelClientEndpoint Use the Tunnel Client's address value in the NAS-IP-Addr attribute (attribute 4) for tunnel users.
T/F juniRadiusClientIncludeAcctTunnelConnectionInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.17	TruthValue	read-write	Enables/disables the inclusion of the Acct-Tunnel-Connection attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeCalledStationIdInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.18	TruthValue	read-write	Enables/disables the inclusion of the Called-Station-ID attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeCallingStationIdInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.19	TruthValue	read-write	Enables/disables the inclusion of the Calling-Station-ID attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeConnectInfoInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.20	TruthValue	read-write	Enables/disables the inclusion of the Connect-Info attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeNasIdentifierInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.21	TruthValue	read-write	Enables/disables the inclusion of the NAS-Identifier attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeNasPortInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.22	TruthValue	read-write	Enables/disables the inclusion of the NAS-Port attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeNasPortIdInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.23	TruthValue	read-write	Enables/disables the inclusion of the NAS-Port-ID attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeNasPortTypeInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.24	TruthValue	read-write	Enables/disables the inclusion of the NAS-Port-Type attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludePppoeDescriptionInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.25	TruthValue	read-write	Enables/disables the inclusion of the PPPoE-Description (VSA) attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeTunnelClientAuthIdInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.26	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Client-Auth-Id attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeTunnelClientEndpointInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.27	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Client-Endpoint attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeTunnelMediumTypeInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.28	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Medium attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeTunnelServerAttributesInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.29	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Server attributes (Tunnel attributes for a PPP session terminated on the LNS) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeTunnelServerAuthIdInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.30	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Server-Auth-Id attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeTunnelServerEndpointInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.31	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Server-Endpoint attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeTunnelTypeInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.32	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Type attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeAcctTunnelConnectionInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.33	TruthValue	read-write	Enables/disables the inclusion of the Acct-Tunnel-Connection attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeCalledStationIdInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.34	TruthValue	read-write	Enables/disables the inclusion of the Called-Station-ID attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeCallingStationIdInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.35	TruthValue	read-write	Enables/disables the inclusion of the Calling-Station-ID attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeClassInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.36	TruthValue	read-write	Enables/disables the inclusion of the Class attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeConnectInfoInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.37	TruthValue	read-write	Enables/disables the inclusion of the Connect-Info attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeEgressPolicyNameInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.38	TruthValue	read-write	Enables/disables the inclusion of the Egress-Policy-Name (VSA) attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeEventTimestampInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.39	TruthValue	read-write	Enables/disables the inclusion of the Event-Timestamp attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeFramedCompressionInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.40	TruthValue	read-write	Enables/disables the inclusion of the Framed-Compression attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeFramedIpNetmaskInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.41	TruthValue	read-write	Enables/disables the inclusion of the Framed-IP-Netmask attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeIngressPolicyNameInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.42	TruthValue	read-write	Enables/disables the inclusion of the Ingress-Policy-Name (VSA) attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeNasIdentifierInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.43	TruthValue	read-write	Enables/disables the inclusion of the NAS-Identifier attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeNasPortInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.44	TruthValue	read-write	Enables/disables the inclusion of the NAS-Port attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeNasPortIdInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.45	TruthValue	read-write	Enables/disables the inclusion of the NAS-Port-ID attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeNasPortTypeInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.46	TruthValue	read-write	Enables/disables the inclusion of the NAS-Port-Type attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludePppoeDescriptionInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.47	TruthValue	read-write	Enables/disables the inclusion of the PPPoE-Description (VSA) attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeTunnelAssignmentIdInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.48	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Assignment-Id attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeTunnelClientAuthIdInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.49	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Client-Auth-Id attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeTunnelClientEndpointInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.50	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Client-Endpoint attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeTunnelMediumTypeInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.51	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Medium attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeTunnelPreferenceInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.52	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Preference attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeTunnelServerAttributesInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.53	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Server attributes (Tunnel attributes for a PPP session terminated on the LNS) in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeTunnelServerAuthIdInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.54	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Server-Auth-Id attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeTunnelServerEndpointInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.55	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Server-Endpoint attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeTunnelTypeInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.56	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Type attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeAcctTunnelConnectionInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.57	TruthValue	read-write	Enables/disables the inclusion of the Acct-Tunnel-Connection attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeCalledStationIdInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.59	TruthValue	read-write	Enables/disables the inclusion of the Called-Station-ID attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeCallingStationIdInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.60	TruthValue	read-write	Enables/disables the inclusion of the Calling-Station-ID attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeClassInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.61	TruthValue	read-write	Enables/disables the inclusion of the Class attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeConnectInfoInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.62	TruthValue	read-write	Enables/disables the inclusion of the Connect-Info attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeEgressPolicyNameInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.63	TruthValue	read-write	Enables/disables the inclusion of the Egress-Policy-Name (VSA) attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeEventTimestampInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.64	TruthValue	read-write	Enables/disables the inclusion of the Event-Timestamp attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeFramedCompressionInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.65	TruthValue	read-write	Enables/disables the inclusion of the Framed-Compression attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeFramedIpNetmaskInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.66	TruthValue	read-write	Enables/disables the inclusion of the Framed-IP-Netmask attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeIngressPolicyNameInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.67	TruthValue	read-write	Enables/disables the inclusion of the Ingress-Policy-Name (VSA) attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeInputGigawordsInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.68	TruthValue	read-write	Enables/disables the inclusion of the Input-Gigawords attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeNasIdentifierInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.69	TruthValue	read-write	Enables/disables the inclusion of the NAS-Identifier attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeNasPortInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.70	TruthValue	read-write	Enables/disables the inclusion of the NAS-Port attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeNasPortIdInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.71	TruthValue	read-write	Enables/disables the inclusion of the NAS-Port-ID attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeNasPortTypeInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.72	TruthValue	read-write	Enables/disables the inclusion of the NAS-Port-Type attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeOutputGigawordsInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.73	TruthValue	read-write	Enables/disables the inclusion of the Output-Gigawords attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludePppoeDescriptionInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.74	TruthValue	read-write	Enables/disables the inclusion of the PPPoE-Description (VSA) attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeTunnelAssignmentIdInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.75	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Assignment-Id attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeTunnelClientAuthIdInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.76	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Client-Auth-Id attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeTunnelClientEndpointInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.77	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Client-Endpoint attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeTunnelMediumTypeInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.78	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Medium attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeTunnelPreferenceInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.79	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Preference attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeTunnelServerAttributesInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.80	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Server attributes (Tunnel attributes for a PPP session terminated on the LNS) in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeTunnelServerAuthIdInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.81	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Server-Auth-Id attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeTunnelServerEndpointInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.82	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Server-Endpoint attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeTunnelTypeInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.83	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Type attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeInputGigapktsInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.84	TruthValue	read-write	Enables/disables the inclusion of the Input-Gigapkts attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeOutputGigapktsInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.85	TruthValue	read-write	Enables/disables the inclusion of the Output-Gigapkts attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIgnoreFramedIpNetmask	1.3.6.1.4.1.4874.2.2.19.1.1.86	TruthValue	read-write	Enables/disables ignoring the Framed-IP-Netmask attribute in the RADIUS Access-Accept packet.
T/F juniRadiusClientIgnoreAtmCategory	1.3.6.1.4.1.4874.2.2.19.1.1.87	TruthValue	read-write	Enables/disables ignoring the ATM-Category (vsa) attribute in the RADIUS Access-Accept packet.
T/F juniRadiusClientIgnoreAtmMbs	1.3.6.1.4.1.4874.2.2.19.1.1.88	TruthValue	read-write	Enables/disables ignoring the ATM-MBS (vsa) attribute in the RADIUS Access-Accept packet.
T/F juniRadiusClientIgnoreAtmPcr	1.3.6.1.4.1.4874.2.2.19.1.1.89	TruthValue	read-write	Enables/disables ignoring the ATM-PCR (vsa) attribute in the RADIUS Access-Accept packet.
T/F juniRadiusClientIgnoreAtmScr	1.3.6.1.4.1.4874.2.2.19.1.1.90	TruthValue	read-write	Enables/disables ignoring the ATM-SCR-Or-CBR (vsa) attribute in the RADIUS Access-Accept packet.
T/F juniRadiusClientIgnoreEgressPolicyName	1.3.6.1.4.1.4874.2.2.19.1.1.91	TruthValue	read-write	Enables/disables ignoring the Egress-Policy-Name (vsa) attribute in the RADIUS Access-Accept packet.
T/F juniRadiusClientIgnoreIngressPolicyName	1.3.6.1.4.1.4874.2.2.19.1.1.92	TruthValue	read-write	Enables/disables ignoring the Ingress-Policy-Name (vsa) attribute in the RADIUS Access-Accept packet.
T/F juniRadiusClientIgnoreVirtualRouter	1.3.6.1.4.1.4874.2.2.19.1.1.93	TruthValue	read-write	Enables/disables ignoring the Virtual-Router (vsa) attribute in the RADIUS Access-Accept packet.
T/F juniRadiusClientTrapOnAuthServerUnavailable	1.3.6.1.4.1.4874.2.2.19.1.1.94	TruthValue	read-write	Enables/disables sending an SNMP trap for the condition that a specific RADIUS authentication server times out.
T/F juniRadiusClientTrapOnAcctServerUnavailable	1.3.6.1.4.1.4874.2.2.19.1.1.95	TruthValue	read-write	Enables/disables sending an SNMP trap for the condition that a specific RADIUS accounting server times out.
T/F juniRadiusClientTrapOnNoAuthServerAvailable	1.3.6.1.4.1.4874.2.2.19.1.1.96	TruthValue	read-write	Enables/disables sending an SNMP trap for the condition that all of the configured RADIUS authentication servers (in a virtual router context) time out.
T/F juniRadiusClientTrapOnNoAcctServerAvailable	1.3.6.1.4.1.4874.2.2.19.1.1.97	TruthValue	read-write	Enables/disables sending an SNMP trap for the condition that all of the configured RADIUS accounting servers (in a virtual router context) time out.
T/F juniRadiusClientTrapOnAuthServerAvailable	1.3.6.1.4.1.4874.2.2.19.1.1.98	TruthValue	read-write	Enables/disables sending an SNMP trap for the condition that a specific RADIUS authentication server has sent a response after being declared unavailable.
T/F juniRadiusClientTrapOnAcctServerAvailable	1.3.6.1.4.1.4874.2.2.19.1.1.99	TruthValue	read-write	Enables/disables sending an SNMP trap for the condition that a specific RADIUS accounting server has sent a response after being declared unavailable.
INT juniRadiusClientPppoeNasPortFormat	1.3.6.1.4.1.4874.2.2.19.1.1.100	INTEGER	read-write	The format used by the client for the Nas-Port attribute (attribute number 5) for PPPoE interfaces: none Use the format specified in juniRadiusClientNasPortFormat unique Use a unique value that is not related to the interface
T/F juniRadiusClientIncludeTunnelInterfaceIdInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.101	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Interface-Id (VSA) attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeTunnelInterfaceIdInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.102	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Interface-Id (VSA) in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeTunnelInterfaceIdInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.103	TruthValue	read-write	Enables/disables the inclusion of the Tunnel-Interface-Id (VSA) in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeL2tpPppDisconnectCauseInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.104	TruthValue	read-write	Enables/disables the inclusion of the L2TP PPP Disconnect Cause (VSA) in the RADIUS Accounting-Stop packet.
INT juniRadiusClientVlanNasPortFormat	1.3.6.1.4.1.4874.2.2.19.1.1.105	INTEGER	read-write	The format used by the client for the Nas-Port attribute (attribute number 5) for VLAN interfaces: none Include the VLAN ID if configured stacked Include both the SVLAN ID and VLAN ID if configured
T/F juniRadiusClientIncludeAcctMultiSessionIdInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.106	TruthValue	read-write	Enables/disables the inclusion of the Accounting Multilink Session ID in the RADIUS Access-Req packet.
T/F juniRadiusClientIncludeAcctMultiSessionIdInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.107	TruthValue	read-write	Enables/disables the inclusion of the Accounting Multilink Session ID in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeAcctMultiSessionIdInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.108	TruthValue	read-write	Enables/disables the inclusion of the Accounting Multilink Session ID in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeAscendNumInMultilinkInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.109	TruthValue	read-write	Enables/disables the inclusion of the Ascend Num In Multilink attribute in the RADIUS Access-Req packet.
T/F juniRadiusClientIncludeAscendNumInMultilinkInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.110	TruthValue	read-write	Enables/disables the inclusion of the Ascend Num In Multilink attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeAscendNumInMultilinkInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.111	TruthValue	read-write	Enables/disables the inclusion of the Ascend Num In Multilink attribute in the RADIUS Accounting-Stop packet.
INT juniRadiusClientConnectInfoFormat	1.3.6.1.4.1.4874.2.2.19.1.1.112	INTEGER	read-write	The format used by the client for the Connect-Info attribute (attribute number 77): default The Connect-Info Attribute is generated from the underlying interface id string. l2tpConnectSpeed The Connect-Info Attribute is generated from the received l2tp connect speed AVPs. The format is in bits per second: [/] The receive connect speed is included if non zero and different from the transmit connect speed. l2tpConnectSpeedRXWhenEqual The Connect-Info Attribute is generated from the received l2tp connect speed AVPs. The format is in bits per second: / The receive connect speed is included if non-zero.
T/F juniRadiusClientIncludeProfileServiceDescrInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.113	TruthValue	read-write	Enables/disables the inclusion of the AAA profile service description attribute in the RADIUS Access-Req packet.
T/F juniRadiusClientIncludeProfileServiceDescrInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.114	TruthValue	read-write	Enables/disables the inclusion of the AAA profile service description attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeProfileServiceDescrInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.115	TruthValue	read-write	Enables/disables the inclusion of the AAA profile service description attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeAcctAuthenticInAcctOn	1.3.6.1.4.1.4874.2.2.19.1.1.116	TruthValue	read-write	Enables/disables the inclusion of the acct-authentic attribute in the RADIUS Accounting-On packet.
T/F juniRadiusClientIncludeAcctDelayTimeInAcctOn	1.3.6.1.4.1.4874.2.2.19.1.1.117	TruthValue	read-write	Enables/disables the inclusion of the acct-delay-time attribute in the RADIUS Accounting-On packet.
T/F juniRadiusClientIncludeAcctSessionIdInAcctOn	1.3.6.1.4.1.4874.2.2.19.1.1.118	TruthValue	read-write	Enables/disables the inclusion of the acct-session-id attribute in the RADIUS Accounting-On packet.
T/F juniRadiusClientIncludeNasIdentifierInAcctOn	1.3.6.1.4.1.4874.2.2.19.1.1.119	TruthValue	read-write	Enables/disables the inclusion of the nas-identifier attribute in the RADIUS Accounting-On packet.
T/F juniRadiusClientIncludeEventTimestampInAcctOn	1.3.6.1.4.1.4874.2.2.19.1.1.120	TruthValue	read-write	Enables/disables the inclusion of the event-timestamp attribute in the RADIUS Accounting-On packet.
T/F juniRadiusClientIncludeAcctAuthenticInAcctOff	1.3.6.1.4.1.4874.2.2.19.1.1.121	TruthValue	read-write	Enables/disables the inclusion of the acct-authentic attribute in the RADIUS Accounting-Off packet.
T/F juniRadiusClientIncludeAcctDelayTimeInAcctOff	1.3.6.1.4.1.4874.2.2.19.1.1.122	TruthValue	read-write	Enables/disables the inclusion of the acct-delay-time attribute in the RADIUS Accounting-Off packet.
T/F juniRadiusClientIncludeAcctSessionIdInAcctOff	1.3.6.1.4.1.4874.2.2.19.1.1.123	TruthValue	read-write	Enables/disables the inclusion of the acct-session-id attribute in the RADIUS Accounting-Off packet.
T/F juniRadiusClientIncludeAcctTerminateCauseInAcctOff	1.3.6.1.4.1.4874.2.2.19.1.1.124	TruthValue	read-write	Enables/disables the inclusion of the acct-terminate-cause attribute in the RADIUS Accounting-Off packet.
T/F juniRadiusClientIncludeNasIdentifierInAcctOff	1.3.6.1.4.1.4874.2.2.19.1.1.125	TruthValue	read-write	Enables/disables the inclusion of the nas-identifier attribute in the RADIUS Accounting-Off packet.
T/F juniRadiusClientIncludeEventTimestampInAcctOff	1.3.6.1.4.1.4874.2.2.19.1.1.126	TruthValue	read-write	Enables/disables the inclusion of the event-timestamp attribute in the RADIUS Accounting-Off packet.
T/F juniRadiusClientIncludeDhcpOptionsInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.127	TruthValue	read-write	Enables/disables the inclusion of the Dhcp-Options (vsa) attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeDhcpMacAddressInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.128	TruthValue	read-write	Enables/disables the inclusion of the Dhcp-Mac-Addresss (vsa) attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeDhcpGiAddressInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.129	TruthValue	read-write	Enables/disables the inclusion of the Dhcp-Gi-Address (vsa) attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeDhcpOptionsInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.130	TruthValue	read-write	Enables/disables the inclusion of the Dhcp-Options (vsa) attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeDhcpMacAddressInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.131	TruthValue	read-write	Enables/disables the inclusion of the Dhcp-Mac-Addresss (vsa) attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeDhcpGiAddressInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.132	TruthValue	read-write	Enables/disables the inclusion of the Dhcp-Gi-Address (vsa) attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeDhcpOptionsInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.133	TruthValue	read-write	Enables/disables the inclusion of the Dhcp-Options (vsa) attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeDhcpMacAddressInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.134	TruthValue	read-write	Enables/disables the inclusion of the Dhcp-Mac-Addresss (vsa) attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeDhcpGiAddressInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.135	TruthValue	read-write	Enables/disables the inclusion of the Dhcp-Gi-Address (vsa) attribute in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientNasPortIdOverrideRemoteCircuitId	1.3.6.1.4.1.4874.2.2.19.1.1.136	TruthValue	read-write	Enables/disables overriding the Nas-Port-Id with the PPPoe Remote Circuit Id.
T/F juniRadiusClientCallingStationIdOverrideRemoteCircuitId	1.3.6.1.4.1.4874.2.2.19.1.1.137	TruthValue	read-write	Enables/disables overriding the Calling-Station-Id with the PPPoe Remote Circuit Id.
T/F juniRadiusClientIncludeMlpppBundleNameInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.138	TruthValue	read-write	Enables/disables the inclusion of the MLPPP-Bundle-Name (VSA) attribute in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeMlpppBundleNameInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.139	TruthValue	read-write	Enables/disables the inclusion of the MLPPP-Bundle-Name (VSA) in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeMlpppBundleNameInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.140	TruthValue	read-write	Enables/disables the inclusion of the MLPPP-Bundle-Name (VSA) in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientOverrideNasInfo	1.3.6.1.4.1.4874.2.2.19.1.1.141	TruthValue	read-write	Enables/disables the overriding nas-ip-address and nas-identifier by values from authentication virual router. If juniRadiusClientNasIpAddrUse is not 'normal', then nas-ip-address is not overriden.
T/F juniRadiusClientIncludeInterfaceDescriptionInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.142	TruthValue	read-write	Enables/disables the inclusion of the interface description attribute in the RADIUS Access-Req packet.
T/F juniRadiusClientIncludeInterfaceDescriptionInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.143	TruthValue	read-write	Enables/disables the inclusion of the interface description attribute in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeInterfaceDescriptionInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.144	TruthValue	read-write	Enables/disables the inclusion of the interface description attribute in the RADIUS Accounting-Stop packet.
INT juniRadiusClientAtmNasPortFormat	1.3.6.1.4.1.4874.2.2.19.1.1.145	INTEGER	read-write	The format used by the client for the Nas-Port attribute (attribute number 5) for ATM interfaces: none Use the format specified in juniRadiusClientNasPortFormat extended Use the extended format determined by atm nas-port field width values.
I32 juniRadiusClientNasPortFieldWidthAtmSlot	1.3.6.1.4.1.4874.2.2.19.1.1.146	Integer32	read-write	Specifies the number of bits in the NAS-Port attribute (attribute 5) to be used for the slot of the atm interface when the value of juniRadiusClientAtmNasPortFormat is extended.
I32 juniRadiusClientNasPortFieldWidthAtmAdapter	1.3.6.1.4.1.4874.2.2.19.1.1.147	Integer32	read-write	Specifies the number of bits in the NAS-Port attribute (attribute 5) to be used for the adapter of the atm interface when the value of juniRadiusClientAtmNasPortFormat is extended.
I32 juniRadiusClientNasPortFieldWidthAtmPort	1.3.6.1.4.1.4874.2.2.19.1.1.148	Integer32	read-write	Specifies the number of bits in the NAS-Port attribute (attribute 5) to be used for the port of the atm interface when the value of juniRadiusClientAtmNasPortFormat is extended.
I32 juniRadiusClientNasPortFieldWidthAtmVpi	1.3.6.1.4.1.4874.2.2.19.1.1.149	Integer32	read-write	Specifies the number of bits in the NAS-Port attribute (attribute 5) to be used for the vpi of the atm interface when the value of juniRadiusClientAtmNasPortFormat is extended.
I32 juniRadiusClientNasPortFieldWidthAtmVci	1.3.6.1.4.1.4874.2.2.19.1.1.150	Integer32	read-write	Specifies the number of bits in the NAS-Port attribute (attribute 5) to be used for the vci of the atm interface when the value of juniRadiusClientAtmNasPortFormat is extended.
INT juniRadiusClientEthernetNasPortFormat	1.3.6.1.4.1.4874.2.2.19.1.1.151	INTEGER	read-write	The format used by the client for the Nas-Port attribute (attribute number 5) for Ethernet interfaces: none Use the format specified in juniRadiusClientNasPortFormat extended Use the extended format determined by ethernet nas-port field width values.
I32 juniRadiusClientNasPortFieldWidthEthernetSlot	1.3.6.1.4.1.4874.2.2.19.1.1.152	Integer32	read-write	Specifies the number of bits in the NAS-Port attribute (attribute 5) to be used for the slot of the ethernet interface when the value of juniRadiusClientEthernetNasPortFormat is extended.
I32 juniRadiusClientNasPortFieldWidthEthernetAdapter	1.3.6.1.4.1.4874.2.2.19.1.1.153	Integer32	read-write	Specifies the number of bits in the NAS-Port attribute (attribute 5) to be used for the adapter of the ethernet interface when the value of juniRadiusClientEthernetNasPortFormat is extended.
I32 juniRadiusClientNasPortFieldWidthEthernetPort	1.3.6.1.4.1.4874.2.2.19.1.1.154	Integer32	read-write	Specifies the number of bits in the NAS-Port attribute (attribute 5) to be used for the port of the ethernet interface when the value of juniRadiusClientEthernetNasPortFormat is extended.
I32 juniRadiusClientNasPortFieldWidthEthernetSVlan	1.3.6.1.4.1.4874.2.2.19.1.1.155	Integer32	read-write	Specifies the number of bits in the NAS-Port attribute (attribute 5) to be used for the svlan of the ethernet interface when the value of juniRadiusClientEthernetNasPortFormat is extended.
I32 juniRadiusClientNasPortFieldWidthEthernetVlan	1.3.6.1.4.1.4874.2.2.19.1.1.156	Integer32	read-write	Specifies the number of bits in the NAS-Port attribute (attribute 5) to be used for the vlan of the ethernet interface when the value of juniRadiusClientEthernetNasPortFormat is extended.
OCT juniRadiusClientRemoteCircuitIdFormat	1.3.6.1.4.1.4874.2.2.19.1.1.157	OCTET STRING	read-write	The set of PPPoE Remote Circuit Id components configured. Each octet in this object contains one of the values defined in the JuniRadiusClientRemoteCircuitIdFormatComponents TEXTUAL-CONVENTION. Only following combinations are permited: agentCircuitId remoteCircuitId agentCircutiId, remoteCircuitId nasIdentifier, agentCircuitId nasIdentifier, remoteCircuitId nasIdentifier, agentCircutiId, remoteCircuitId dsl-format-1.
STR juniRadiusClientRemoteCircuitIdDelimiter	1.3.6.1.4.1.4874.2.2.19.1.1.158	DisplayString	read-write	The character use as for delimiting fields in the PPPoE Remote Circuit ID. The default value is '#'.
T/F juniRadiusClientIncludeL2cAccessLoopParametersInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.159	TruthValue	read-write	Enables/disables the inclusion of the l2c-access-loop-parameters (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cDownStreamDataInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.160	TruthValue	read-write	Enables/disables the inclusion of the l2c-down-stream-data (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cUpStreamDataInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.161	TruthValue	read-write	Enables/disables the inclusion of the l2c-up-stream-data (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cDownStreamDataInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.162	TruthValue	read-write	Enables/disables the inclusion of the l2c-down-stream-data (VSA) in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeL2cUpStreamDataInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.163	TruthValue	read-write	Enables/disables the inclusion of the l2c-up-stream-data (VSA) in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeL2cDownStreamDataInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.164	TruthValue	read-write	Enables/disables the inclusion of the l2c-down-stream-data (VSA) in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeL2cUpStreamDataInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.165	TruthValue	read-write	Enables/disables the inclusion of the l2c-up-stream-data (VSA) in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeDslForumAttributesInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.166	TruthValue	read-write	Enables/disables the inclusion of the DSL Forum attributes (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeDslForumAttributesInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.167	TruthValue	read-write	Enables/disables the inclusion of the DSL Forum attributes (VSA) in the RADIUS Accounting-Start packet.
T/F juniRadiusClientIncludeDslForumAttributesInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.168	TruthValue	read-write	Enables/disables the inclusion of the DSL Forum attributes (VSA) in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeL2cAccessLoopCircuitIdInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.169	TruthValue	read-write	Enables/disables the inclusion of l2cd-acc-loop-cir-id (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cAccessAggrCircuitIdBinaryInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.170	TruthValue	read-write	Enables/disables the inclusion of l2cd-acc-aggr-cir-id-bin (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cAccessAggrCircuitIdAsciiInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.171	TruthValue	read-write	Enables/disables the inclusion of l2cd-acc-aggr-cir-id-asc (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cActualDataRateUstrInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.172	TruthValue	read-write	Enables/disables the inclusion of l2cd-act-data-rate-up (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cActualDataRateDstrInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.173	TruthValue	read-write	Enables/disables the inclusion of l2cd-act-data-rate-dn (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cMinimumDataRateUstrInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.174	TruthValue	read-write	Enables/disables the inclusion of l2cd-min-data-rate-up (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cMinimumDataRateDstrInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.175	TruthValue	read-write	Enables/disables the inclusion of l2cd-in-data-rate-dn (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cAttainDataRateUstrInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.176	TruthValue	read-write	Enables/disables the inclusion of l2cd-att-data-rate-up (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cAttainDataRateDstrInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.177	TruthValue	read-write	Enables/disables the inclusion of l2cd-att-data-rate-dn (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cMaximumDataRateUstrInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.178	TruthValue	read-write	Enables/disables the inclusion of l2cd-max-data-rate-up (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cMaximumDataRateDstrInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.179	TruthValue	read-write	Enables/disables the inclusion of l2cd-max-data-rate-dn (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cMinLowPowerDataRateUstrInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.180	TruthValue	read-write	Enables/disables the inclusion of l2cd-min-lp-data-rate-up (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cMinLowPowerDataRateDstrInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.181	TruthValue	read-write	Enables/disables the inclusion of l2cd-min-lp-data-rate-dn (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cMaxInterleavingDelayUstrInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.182	TruthValue	read-write	Enables/disables the inclusion of l2cd-max-interlv-delay-up (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cActInterleavingDelayUstrInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.183	TruthValue	read-write	Enables/disables the inclusion of l2cd-act-interlv-delay-up (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cMaxInterleavingDelayDstrInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.184	TruthValue	read-write	Enables/disables the inclusion of l2cd-max-interlv-delay-dn (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cActInterleavingDelayDstrInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.185	TruthValue	read-write	Enables/disables the inclusion of l2cd-act-interlv-delay-dn (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cDslLineStateInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.186	TruthValue	read-write	Enables/disables the inclusion of l2cd-dsl-line-state (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cDslTypeInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.187	TruthValue	read-write	Enables/disables the inclusion of l2cd-dsl-type (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeL2cAccessLoopCircuitIdInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.188	TruthValue	read-write	Enables/disables the inclusion of l2cd-acc-loop-cir-id (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cAccessAggrCircuitIdBinaryInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.189	TruthValue	read-write	Enables/disables the inclusion of l2cd-acc-aggr-cir-id-bin (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cAccessAggrCircuitIdAsciiInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.190	TruthValue	read-write	Enables/disables the inclusion of l2cd-acc-aggr-cir-id-asc (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cActualDataRateUstrInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.191	TruthValue	read-write	Enables/disables the inclusion of l2cd-act-data-rate-up (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cActualDataRateDstrInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.192	TruthValue	read-write	Enables/disables the inclusion of l2cd-act-data-rate-dn (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cMinimumDataRateUstrInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.193	TruthValue	read-write	Enables/disables the inclusion of l2cd-min-data-rate-up (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cMinimumDataRateDstrInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.194	TruthValue	read-write	Enables/disables the inclusion of l2cd-in-data-rate-dn (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cAttainDataRateUstrInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.195	TruthValue	read-write	Enables/disables the inclusion of l2cd-att-data-rate-up (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cAttainDataRateDstrInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.196	TruthValue	read-write	Enables/disables the inclusion of l2cd-att-data-rate-dn (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cMaximumDataRateUstrInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.197	TruthValue	read-write	Enables/disables the inclusion of l2cd-max-data-rate-up (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cMaximumDataRateDstrInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.198	TruthValue	read-write	Enables/disables the inclusion of l2cd-max-data-rate-dn (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cMinLowPowerDataRateUstrInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.199	TruthValue	read-write	Enables/disables the inclusion of l2cd-min-lp-data-rate-up (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cMinLowPowerDataRateDstrInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.200	TruthValue	read-write	Enables/disables the inclusion of l2cd-min-lp-data-rate-dn (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cMaxInterleavingDelayUstrInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.201	TruthValue	read-write	Enables/disables the inclusion of l2cd-max-interlv-delay-up (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cActInterleavingDelayUstrInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.202	TruthValue	read-write	Enables/disables the inclusion of l2cd-act-interlv-delay-up (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cMaxInterleavingDelayDstrInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.203	TruthValue	read-write	Enables/disables the inclusion of l2cd-max-interlv-delay-dn (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cActInterleavingDelayDstrInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.204	TruthValue	read-write	Enables/disables the inclusion of l2cd-act-interlv-delay-dn (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cDslLineStateInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.205	TruthValue	read-write	Enables/disables the inclusion of l2cd-dsl-line-state (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cDslTypeInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.206	TruthValue	read-write	Enables/disables the inclusion of l2cd-dsl-type (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeL2cAccessLoopCircuitIdInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.207	TruthValue	read-write	Enables/disables the inclusion of l2cd-acc-loop-cir-id (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cAccessAggrCircuitIdBinaryInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.208	TruthValue	read-write	Enables/disables the inclusion of l2cd-acc-aggr-cir-id-bin (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cAccessAggrCircuitIdAsciiInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.209	TruthValue	read-write	Enables/disables the inclusion of l2cd-acc-aggr-cir-id-asc (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cActualDataRateUstrInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.210	TruthValue	read-write	Enables/disables the inclusion of l2cd-act-data-rate-up (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cActualDataRateDstrInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.211	TruthValue	read-write	Enables/disables the inclusion of l2cd-act-data-rate-dn (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cMinimumDataRateUstrInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.212	TruthValue	read-write	Enables/disables the inclusion of l2cd-min-data-rate-up (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cMinimumDataRateDstrInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.213	TruthValue	read-write	Enables/disables the inclusion of l2cd-in-data-rate-dn (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cAttainDataRateUstrInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.214	TruthValue	read-write	Enables/disables the inclusion of l2cd-att-data-rate-up (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cAttainDataRateDstrInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.215	TruthValue	read-write	Enables/disables the inclusion of l2cd-att-data-rate-dn (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cMaximumDataRateUstrInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.216	TruthValue	read-write	Enables/disables the inclusion of l2cd-max-data-rate-up (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cMaximumDataRateDstrInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.217	TruthValue	read-write	Enables/disables the inclusion of l2cd-max-data-rate-dn (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cMinLowPowerDataRateUstrInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.218	TruthValue	read-write	Enables/disables the inclusion of l2cd-min-lp-data-rate-up (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cMinLowPowerDataRateDstrInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.219	TruthValue	read-write	Enables/disables the inclusion of l2cd-min-lp-data-rate-dn (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cMaxInterleavingDelayUstrInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.220	TruthValue	read-write	Enables/disables the inclusion of l2cd-max-interlv-delay-up (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cActInterleavingDelayUstrInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.221	TruthValue	read-write	Enables/disables the inclusion of l2cd-act-interlv-delay-up (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cMaxInterleavingDelayDstrInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.222	TruthValue	read-write	Enables/disables the inclusion of l2cd-max-interlv-delay-dn (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cActInterleavingDelayDstrInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.223	TruthValue	read-write	Enables/disables the inclusion of l2cd-act-interlv-delay-dn (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cDslLineStateInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.224	TruthValue	read-write	Enables/disables the inclusion of l2cd-dsl-line-state (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeL2cDslTypeInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.225	TruthValue	read-write	Enables/disables the inclusion of l2cd-dsl-type (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeInterfaceIdInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.226	TruthValue	read-write	Enables/disables the inclusion of framed-interface-id (96) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeIpv6PrefixInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.227	TruthValue	read-write	Enables/disables the inclusion of framed-ipv6-prefix (97) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeInterfaceIdInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.228	TruthValue	read-write	Enables/disables the inclusion of framed-interface-id (96) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeIpAddrInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.229	TruthValue	read-write	Enables/disables the inclusion of framed-ip-address (8) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeIpv6PrefixInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.230	TruthValue	read-write	Enables/disables the inclusion of framed-ipv6-prefix (97) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeDownStreamCalculatedQosRateInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.231	TruthValue	read-write	Enables/disables the inclusion of downstream-calculated-qos-rate (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeUpStreamCalculatedQosRateInAccessReq	1.3.6.1.4.1.4874.2.2.19.1.1.232	TruthValue	read-write	Enables/disables the inclusion of upstream-calculated-qos-rate (VSA) in the RADIUS Access-Request packet.
T/F juniRadiusClientIncludeDownStreamCalculatedQosRateInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.233	TruthValue	read-write	Enables/disables the inclusion of downstream-calculated-qos-rate (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeUpStreamCalculatedQosRateInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.234	TruthValue	read-write	Enables/disables the inclusion of upstream-calculated-qos-rate (VSA) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeDownStreamCalculatedQosRateInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.235	TruthValue	read-write	Enables/disables the inclusion of downstream-calculated-qos-rate (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeUpStreamCalculatedQosRateInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.236	TruthValue	read-write	Enables/disables the inclusion of upstream-calculated-qos-rate (VSA) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIgnorePppoeMaxSession	1.3.6.1.4.1.4874.2.2.19.1.1.237	TruthValue	read-write	Enables/disables ignoring the PPPoE Max Session (vsa) attribute in the RADIUS Access-Accept packet.
T/F juniRadiusClientIncludeIpv6AccountingInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.238	TruthValue	read-write	Enables/disables the inclusion of the IPv6 Accounting (VSA) attributes in the RADIUS Accounting-Stop packet.
T/F juniRadiusClientIncludeDelegatedIpv6PrefixInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.239	TruthValue	read-write	Enables/disables the inclusion of delegated-ipv6-prefix (123) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeDelegatedIpv6PrefixInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.240	TruthValue	read-write	Enables/disables the inclusion of delegated-ipv6-prefix (123) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeFramedIpv6PoolInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.241	TruthValue	read-write	Enables/disables the inclusion of framed-ipv6-pool (100) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeFramedIpv6PoolInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.242	TruthValue	read-write	Enables/disables the inclusion of framed-ipv6-pool (100) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeFramedIpv6RouteInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.243	TruthValue	read-write	Enables/disables the inclusion of framed-ipv6-route (99) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeFramedIpv6RouteInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.244	TruthValue	read-write	Enables/disables the inclusion of framed-ipv6-route (99) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeIpv6LocalInterfaceInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.245	TruthValue	read-write	Enables/disables the inclusion of ipv6-local-interface (vsa) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeIpv6LocalInterfaceInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.246	TruthValue	read-write	Enables/disables the inclusion of ipv6-local-interface (vsa) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeIpv6NdRaPrefixInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.247	TruthValue	read-write	Enables/disables the inclusion of ipv6-nd-ra-prefix (vsa) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeIpv6NdRaPrefixInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.248	TruthValue	read-write	Enables/disables the inclusion of ipv6-nd-ra-prefix (vsa) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeIpv6PrimaryDnsInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.249	TruthValue	read-write	Enables/disables the inclusion of ipv6-primary-dns (vsa) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeIpv6PrimaryDnsInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.250	TruthValue	read-write	Enables/disables the inclusion of ipv6-primary-dns (vsa) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeIpv6SecondaryDnsInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.251	TruthValue	read-write	Enables/disables the inclusion of ipv6-secondary-dns (vsa) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeIpv6SecondaryDnsInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.252	TruthValue	read-write	Enables/disables the inclusion of ipv6-secondary-dns (vsa) in the RADIUS Acct-Stop packet.
T/F juniRadiusClientIncludeIpv6VirtualRouterInAcctStart	1.3.6.1.4.1.4874.2.2.19.1.1.253	TruthValue	read-write	Enables/disables the inclusion of ipv6-virtual-router (vsa) in the RADIUS Acct-Start packet.
T/F juniRadiusClientIncludeIpv6VirtualRouterInAcctStop	1.3.6.1.4.1.4874.2.2.19.1.1.254	TruthValue	read-write	Enables/disables the inclusion of ipv6-virtual-router (vsa) in the RADIUS Acct-Stop packet.
juniRadiusAuthClient	1.3.6.1.4.1.4874.2.2.19.1.2
C32 juniRadiusAuthClientInvalidServerAddressesEx	1.3.6.1.4.1.4874.2.2.19.1.2.1	Counter32	read-only	The number of RADIUS Access-Response packets received from unknown addresses.
juniRadiusAuthClientServerTable	1.3.6.1.4.1.4874.2.2.19.1.2.2		not-accessible	The (conceptual) table listing the RADIUS authentication servers with which the client shares a secret.
juniRadiusAuthClientServerEntry	1.3.6.1.4.1.4874.2.2.19.1.2.2.1		not-accessible	An entry (conceptual row) representing a RADIUS authentication server with which the client shares a secret.
IP juniRadiusAuthClientServerAddress	1.3.6.1.4.1.4874.2.2.19.1.2.2.1.1	IpAddress	not-accessible	The IP address of the RADIUS authentication server referred to in this table entry. A value of 0.0.0.0 indicates this entry is not in use.
I32 juniRadiusAuthClientServerPortNumber	1.3.6.1.4.1.4874.2.2.19.1.2.2.1.2	Integer32	read-only	The UDP port the client is using to send requests to this server.
TIK juniRadiusAuthClientRoundTripTime	1.3.6.1.4.1.4874.2.2.19.1.2.2.1.3	TimeTicks	read-only	The time interval (in hundredths of seconds) between the most recent Access-Reply/Access-Challenge and the Access-Request that matched it from this RADIUS authentication server.
C32 juniRadiusAuthClientAccessRequests	1.3.6.1.4.1.4874.2.2.19.1.2.2.1.4	Counter32	read-only	The number of RADIUS Access-Request packets sent to this server. This does not include retransmissions.
C32 juniRadiusAuthClientAccessRetransmissions	1.3.6.1.4.1.4874.2.2.19.1.2.2.1.5	Counter32	read-only	The number of RADIUS Access-Request packets retransmitted to this RADIUS authentication server.
C32 juniRadiusAuthClientAccessAccepts	1.3.6.1.4.1.4874.2.2.19.1.2.2.1.6	Counter32	read-only	The number of RADIUS Access-Accept packets (valid or invalid) received from this server.
C32 juniRadiusAuthClientAccessRejects	1.3.6.1.4.1.4874.2.2.19.1.2.2.1.7	Counter32	read-only	The number of RADIUS Access-Reject packets (valid or invalid) received from this server.
C32 juniRadiusAuthClientAccessChallenges	1.3.6.1.4.1.4874.2.2.19.1.2.2.1.8	Counter32	read-only	The number of RADIUS Access-Challenge packets (valid or invalid) received from this server.
C32 juniRadiusAuthClientMalformedAccessResponses	1.3.6.1.4.1.4874.2.2.19.1.2.2.1.9	Counter32	read-only	The number of malformed RADIUS Access-Response packets received from this server. Malformed packets include packets with an invalid length. Bad authenticators or signature attributes or unknown types are not included as malformed access responses.
C32 juniRadiusAuthClientBadAuthenticators	1.3.6.1.4.1.4874.2.2.19.1.2.2.1.10	Counter32	read-only	The number of RADIUS Access-Response packets containing invalid authenticators or signature attributes received from this server.
G32 juniRadiusAuthClientPendingRequests	1.3.6.1.4.1.4874.2.2.19.1.2.2.1.11	Gauge32	read-only	The number of RADIUS Access-Request packets destined for this server that have not yet timed out or received a response. This variable is incremented when an Access-Request is sent and decremented due to receipt of an Access-Accept, Access-Reject or Access-Challenge, a timeout or retransmission.
C32 juniRadiusAuthClientTimeouts	1.3.6.1.4.1.4874.2.2.19.1.2.2.1.12	Counter32	read-only	The number of authentication timeouts to this server. After a timeout the client may retry to the same server, send to a different server, or give up. A retry to the same server is counted as a retransmit as well as a timeout. A send to a different server is counted as a Request as well as a timeout.
C32 juniRadiusAuthClientUnknownTypes	1.3.6.1.4.1.4874.2.2.19.1.2.2.1.13	Counter32	read-only	The number of RADIUS packets of unknown type which were received from this server on the authentication port.
C32 juniRadiusAuthClientPacketsDropped	1.3.6.1.4.1.4874.2.2.19.1.2.2.1.14	Counter32	read-only	The number of RADIUS packets of which were received from this server on the authentication port and dropped for some other reason.
juniRadiusAuthClientCfgServerTable	1.3.6.1.4.1.4874.2.2.19.1.2.3		not-accessible	The (conceptual) table listing the RADIUS authentication servers with which the client shares a secret.
juniRadiusAuthClientCfgServerEntry	1.3.6.1.4.1.4874.2.2.19.1.2.3.1		not-accessible	An entry (conceptual row) representing a RADIUS authentication server with which the client shares a secret.
IP juniRadiusAuthClientCfgServerAddress	1.3.6.1.4.1.4874.2.2.19.1.2.3.1.1	IpAddress	not-accessible	The IP address of the RADIUS authentication server referred to in this table entry.
I32 juniRadiusAuthClientCfgServerPortNumber	1.3.6.1.4.1.4874.2.2.19.1.2.3.1.2	Integer32	read-create	The UDP port the client is using to send requests to this server.
STR juniRadiusAuthClientCfgKey	1.3.6.1.4.1.4874.2.2.19.1.2.3.1.3	DisplayString	read-create	The secret (RADIUS authenticator) used by the client during exchanges with this authentication server. The default is a zero-length string, indicating no authenticator is used.
I32 juniRadiusAuthClientCfgTimeoutInterval	1.3.6.1.4.1.4874.2.2.19.1.2.3.1.4	Integer32	read-create	The interval between retransmissions of a request to this authentication server.
I32 juniRadiusAuthClientCfgRetries	1.3.6.1.4.1.4874.2.2.19.1.2.3.1.5	Integer32	read-create	The maximum number of times to resend a request to this authentication server (in addition to the original request), before resorting to the server specified in the next entry.
I32 juniRadiusAuthClientCfgMaxPendingRequests	1.3.6.1.4.1.4874.2.2.19.1.2.3.1.6	Integer32	read-create	The maximum number of outstanding requests this server can support.
ROW juniRadiusAuthClientCfgRowStatus	1.3.6.1.4.1.4874.2.2.19.1.2.3.1.7	RowStatus	read-create	Supports 'createAndGo' and 'destroy' only.
I32 juniRadiusAuthClientCfgPrecedence	1.3.6.1.4.1.4874.2.2.19.1.2.3.1.8	Integer32	read-only	Relative precedence of this server with respect to other servers configured in this table. Lower values correspond to higher precedence. Precedence is assigned by the device, in order of entry creation, from higher to lower precedence.
I32 juniRadiusAuthClientCfgDeadTime	1.3.6.1.4.1.4874.2.2.19.1.2.3.1.9	Integer32	read-create	The period of time, in minutes, to ignore this server after a request to the server times out (thereby avoiding additional request timeouts for this period, if the server failure persists).
juniRadiusAcctClient	1.3.6.1.4.1.4874.2.2.19.1.3
C32 juniRadiusAcctClientInvalidServerAddresses	1.3.6.1.4.1.4874.2.2.19.1.3.1	Counter32	read-only	The number of RADIUS Accounting-Response packets received from unknown addresses.
juniRadiusAcctClientServerTable	1.3.6.1.4.1.4874.2.2.19.1.3.2		not-accessible	The (conceptual) table listing the RADIUS accounting servers with which the client shares a secret.
juniRadiusAcctClientServerEntry	1.3.6.1.4.1.4874.2.2.19.1.3.2.1		not-accessible	An entry (conceptual row) representing a RADIUS accounting server with which the client shares a secret.
IP juniRadiusAcctClientServerAddress	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.1	IpAddress	not-accessible	The IP address of the RADIUS accounting server referred to in this table entry. A value of 0.0.0.0 indicates this entry is not in use.
I32 juniRadiusAcctClientServerPortNumber	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.2	Integer32	read-only	The UDP port the client is using to send requests to this server.
TIK juniRadiusAcctClientRoundTripTime	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.3	TimeTicks	read-only	The time interval between the most recent Accounting-Response and the Accounting-Request that matched it from this RADIUS accounting server.
C32 juniRadiusAcctClientRequests	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.4	Counter32	read-only	The number of RADIUS Accounting-Request packets sent. This does not include retransmissions.
C32 juniRadiusAcctClientRetransmissions	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.5	Counter32	read-only	The number of RADIUS Accounting-Request packets retransmitted to this RADIUS accounting server. Retransmissions include retries where the Identifier and Acct-Delay have been updated, as well as those in which they remain the same.
C32 juniRadiusAcctClientResponses	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.6	Counter32	read-only	The number of RADIUS packets received on the accounting port from this server.
C32 juniRadiusAcctClientMalformedResponses	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.7	Counter32	read-only	The number of malformed RADIUS Accounting-Response packets received from this server. Malformed packets include packets with an invalid length. Bad authenticators and unknown types are not included as malformed accounting responses.
C32 juniRadiusAcctClientBadAuthenticators	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.8	Counter32	read-only	The number of RADIUS Accounting-Response packets which contained invalid authenticators received from this server.
G32 juniRadiusAcctClientPendingRequests	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.9	Gauge32	read-only	The number of RADIUS Accounting-Request packets sent to this server that have not yet timed out or received a response. This variable is incremented when an Accounting-Request is sent and decremented due to receipt of an Accounting-Response, a timeout or a retransmission.
C32 juniRadiusAcctClientTimeouts	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.10	Counter32	read-only	The number of accounting timeouts to this server. After a timeout the client may retry to the same server, send to a different server, or give up. A retry to the same server is counted as a retransmit as well as a timeout. A send to a different server is counted as an Accounting-Request as well as a timeout.
C32 juniRadiusAcctClientUnknownTypes	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.11	Counter32	read-only	The number of RADIUS packets of unknown type which were received from this server on the accounting port.
C32 juniRadiusAcctClientPacketsDropped	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.12	Counter32	read-only	The number of RADIUS packets which were received from this server on the accounting port and dropped for some other reason.
C32 juniRadiusAcctClientStartRequests	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.13	Counter32	read-only	The number of RADIUS Accounting-Start request packets sent. This does not include retransmissions.
C32 juniRadiusAcctClientInterimRequests	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.14	Counter32	read-only	The number of RADIUS Accounting-Interim request packets sent. This does not include retransmissions.
C32 juniRadiusAcctClientStopRequests	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.15	Counter32	read-only	The number of RADIUS Accounting-Stop request packets sent. This does not include retransmissions.
C32 juniRadiusAcctClientStartResponses	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.16	Counter32	read-only	The number of RADIUS accounting-start response packets received on the accounting port from this server.
C32 juniRadiusAcctClientInterimResponses	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.17	Counter32	read-only	The number of RADIUS accounting-interim response packets received on the accounting port from this server.
C32 juniRadiusAcctClientStopResponses	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.18	Counter32	read-only	The number of RADIUS accounting-stop response packets received on the accounting port from this server.
C32 juniRadiusAcctClientRejectRequests	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.19	Counter32	read-only	The number of RADIUS accounting-reject packets sent on the accounting port from this server.
C32 juniRadiusAcctClientRejectResponses	1.3.6.1.4.1.4874.2.2.19.1.3.2.1.20	Counter32	read-only	The number of RADIUS accounting-reject response packets received on the accounting port from this server.
juniRadiusAcctClientCfgServerTable	1.3.6.1.4.1.4874.2.2.19.1.3.3		not-accessible	The (conceptual) table listing the RADIUS accounting servers with which the client shares a secret.
juniRadiusAcctClientCfgServerEntry	1.3.6.1.4.1.4874.2.2.19.1.3.3.1		not-accessible	An entry (conceptual row) representing a RADIUS accounting server with which the client shares a secret.
IP juniRadiusAcctClientCfgServerAddress	1.3.6.1.4.1.4874.2.2.19.1.3.3.1.1	IpAddress	not-accessible	The IP address of the RADIUS accounting server referred to in this table entry.
I32 juniRadiusAcctClientCfgServerPortNumber	1.3.6.1.4.1.4874.2.2.19.1.3.3.1.2	Integer32	read-create	The UDP port the client is using to send requests to this server.
STR juniRadiusAcctClientCfgKey	1.3.6.1.4.1.4874.2.2.19.1.3.3.1.3	DisplayString	read-create	The secret (RADIUS authenticator) used by the client during exchanges with this accounting server. The default is a zero-length string, indicating no authenticator is used.
I32 juniRadiusAcctClientCfgTimeoutInterval	1.3.6.1.4.1.4874.2.2.19.1.3.3.1.4	Integer32	read-create	The interval between retransmissions of a request to this accounting server.
I32 juniRadiusAcctClientCfgRetries	1.3.6.1.4.1.4874.2.2.19.1.3.3.1.5	Integer32	read-create	The maximum number of times to resend a request to this accounting server (in addition to the original request), before resorting to the server specified in the next entry.
I32 juniRadiusAcctClientCfgMaxPendingRequests	1.3.6.1.4.1.4874.2.2.19.1.3.3.1.6	Integer32	read-create	The maximum number of outstanding requests this server can support.
ROW juniRadiusAcctClientCfgRowStatus	1.3.6.1.4.1.4874.2.2.19.1.3.3.1.7	RowStatus	read-create	Supports 'createAndGo' and 'destroy' only.
I32 juniRadiusAcctClientCfgPrecedence	1.3.6.1.4.1.4874.2.2.19.1.3.3.1.8	Integer32	read-only	Relative precedence of this server with respect to other servers configured in this table. Lower values correspond to higher precedence. Precedence is assigned by the device, in order of entry creation, from higher to lower precedence.
I32 juniRadiusAcctClientCfgDeadTime	1.3.6.1.4.1.4874.2.2.19.1.3.3.1.9	Integer32	read-create	The period of time, in minutes, to ignore this server after a request to the server times out (thereby avoiding additional request timeouts for this period, if the server failure persists).
juniRadiusClientMIBConformance	1.3.6.1.4.1.4874.2.2.19.2
juniRadiusClientMIBCompliances	1.3.6.1.4.1.4874.2.2.19.2.1
juniRadiusAuthClientCompliance	1.3.6.1.4.1.4874.2.2.19.2.1.1			Obsolete compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality. This statement became obsolete when the juniRadiusClientSourceAddress object was added.
juniRadiusAcctClientCompliance	1.3.6.1.4.1.4874.2.2.19.2.1.2			Obsolete compliance statement for accounting clients implementing the Juniper RADIUS Client MIB accounting functionality. This statement became obsolete when the juniRadiusClientSourceAddress object was added.
juniRadiusAuthClientCompliance2	1.3.6.1.4.1.4874.2.2.19.2.1.3			Obsolete compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality. This statement became obsolete when new objects were added.
juniRadiusAcctClientCompliance2	1.3.6.1.4.1.4874.2.2.19.2.1.4			Obsolete compliance statement for accounting clients implementing the Juniper RADIUS Client MIB accounting functionality. This statement became obsolete when new objects were added.
juniRadiusClientCompliance	1.3.6.1.4.1.4874.2.2.19.2.1.5			Obsolete compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality. This statement became obsolete when new B-RAS objects were added.
juniRadiusClientCompliance2	1.3.6.1.4.1.4874.2.2.19.2.1.6			Obsolete compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality. This statement became obsolete when new objects were added.
juniRadiusClientCompliance3	1.3.6.1.4.1.4874.2.2.19.2.1.7			Obsolete compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality. This statement became obsolete when the juniRadiusClientNasIpAddrUse object was added.
juniRadiusClientCompliance4	1.3.6.1.4.1.4874.2.2.19.2.1.8			Obsolete compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality. This statement became obsolete when objects were added to indicate which RADIUS attributes should be included or excluded from RADIUS packets.
juniRadiusClientCompliance5	1.3.6.1.4.1.4874.2.2.19.2.1.9			Obsolete compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality. This statement became obsolete when notifications for unavailable RADIUS servers were added.
juniRadiusClientCompliance6	1.3.6.1.4.1.4874.2.2.19.2.1.10			Obsolete compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality. This statement became obsolete when attribute-ignore objects were added to the B-RAS group and accounting and authetication servers available notifications were added.
juniRadiusClientCompliance7	1.3.6.1.4.1.4874.2.2.19.2.1.11			Obsolete compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality. This statement became obsolete when authentication and accounting objects were added.
juniRadiusClientCompliance8	1.3.6.1.4.1.4874.2.2.19.2.1.12			Obsolete compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality. This statement became obsolete when accounting reject counters were added.
juniRadiusClientCompliance9	1.3.6.1.4.1.4874.2.2.19.2.1.13			Obsolete compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality. This statement became obsolete when new object was added to the BRAS group to indicate which RADIUS attributes should be included or excluded from RADIUS packets.
juniRadiusClientCompliance10	1.3.6.1.4.1.4874.2.2.19.2.1.14			Obsolete compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality. This statement became obsolete when new objects were added to indicate which RADIUS attributes for DHCP VSAs should be included or excluded from RADIUS packets.
juniRadiusClientCompliance11	1.3.6.1.4.1.4874.2.2.19.2.1.15			Obsolete compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality.
juniRadiusClientCompliance12	1.3.6.1.4.1.4874.2.2.19.2.1.16			Obsolete compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality.
juniRadiusClientCompliance13	1.3.6.1.4.1.4874.2.2.19.2.1.17			Obsolete compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality.
juniRadiusClientCompliance14	1.3.6.1.4.1.4874.2.2.19.2.1.18			The compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality.
juniRadiusClientCompliance15	1.3.6.1.4.1.4874.2.2.19.2.1.19			Obsolete compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality.
juniRadiusClientCompliance16	1.3.6.1.4.1.4874.2.2.19.2.1.20			The compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality.
juniRadiusClientCompliance17	1.3.6.1.4.1.4874.2.2.19.2.1.21			The compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality.
juniRadiusClientCompliance18	1.3.6.1.4.1.4874.2.2.19.2.1.22			The compliance statement for authentication clients implementing the Juniper RADIUS Client MIB authentication functionality.
juniRadiusClientMIBGroups	1.3.6.1.4.1.4874.2.2.19.2.2
juniRadiusGeneralClientGroup	1.3.6.1.4.1.4874.2.2.19.2.2.1			Obsolete basic collection of objects providing management of RADIUS Clients. This group became obsolete when juniRadiusClientSourceAddress was added.
juniRadiusAuthClientGroup	1.3.6.1.4.1.4874.2.2.19.2.2.2			Obsolete collection of objects providing management of RADIUS Authentication Clients. This group became obsolete when notification objects for an unavailable authentication server were added.
juniRadiusAcctClientGroup	1.3.6.1.4.1.4874.2.2.19.2.2.3			Obsolete collection of objects providing management of RADIUS Accounting Clients. This group became obsolete when notification objects for an unavailable accounting server were added.
juniRadiusGeneralClientGroup2	1.3.6.1.4.1.4874.2.2.19.2.2.4			Obsolete basic collection of objects providing management of RADIUS Clients. This group became obsolete when new objects were added.
juniRadiusBasicClientGroup	1.3.6.1.4.1.4874.2.2.19.2.2.5			Obsolete collection of objects providing basic management of RADIUS Clients. This group became obsolete when the juniRadiusClientRollover object was added.
juniRadiusBrasClientGroup	1.3.6.1.4.1.4874.2.2.19.2.2.6			Obsolete collection of objects providing management of general B-RAS functions for RADIUS Clients. This group became obsolete when new objects were added.
juniRadiusTunnelClientGroup	1.3.6.1.4.1.4874.2.2.19.2.2.7			An object providing management of tunneling functions for RADIUS Clients.
juniRadiusBrasClientGroup2	1.3.6.1.4.1.4874.2.2.19.2.2.8			Obsolete collection of objects providing management of general B-RAS functions for RADIUS Clients. This group became obsolete when the juniRadiusClientCallingStationIdFormat object was added.
juniRadiusBasicClientGroup2	1.3.6.1.4.1.4874.2.2.19.2.2.9			A collection of objects providing basic management of RADIUS Clients.
juniRadiusBrasClientGroup3	1.3.6.1.4.1.4874.2.2.19.2.2.10			Obsolete collection of objects providing management of general B-RAS functions for RADIUS Clients. This group became obsolete when the juniRadiusClientNasIpAddrUse object was added.
juniRadiusBrasClientGroup4	1.3.6.1.4.1.4874.2.2.19.2.2.11			Obsolete collection of objects providing management of general B-RAS functions for RADIUS Clients. This group became obsolete when objects were added to indicate which RADIUS attributes should be included or excluded from RADIUS packets.
juniRadiusBrasClientGroup5	1.3.6.1.4.1.4874.2.2.19.2.2.12			Obsolete collection of objects providing management of general B-RAS functions for RADIUS Clients. This group became obsolete when objects to ignore attributes and enable/disable traps were added.
juniRadiusAuthClientGroup2	1.3.6.1.4.1.4874.2.2.19.2.2.13			Obsolete collection of objects providing management of RADIUS Authentication Clients. This group became obsolete when authentication server available notification support was added.
juniRadiusAcctClientGroup2	1.3.6.1.4.1.4874.2.2.19.2.2.14			Obsolete collection of objects providing management of RADIUS Accounting Clients. This group became obsolete when detailed accounting statistics and accounting server available notification support were added.
juniRadiusAuthNotificationGroup	1.3.6.1.4.1.4874.2.2.19.2.2.15			Obsolete collection of management notifications for RADUIS authentication events. This group became obsolete when authentication server available notification was added.
juniRadiusAcctNotificationGroup	1.3.6.1.4.1.4874.2.2.19.2.2.16			Obsolete collection of management notifications for RADUIS accounting events. This group became obsolete when accounting server available notification was added.
juniRadiusBrasClientGroup6	1.3.6.1.4.1.4874.2.2.19.2.2.17			Obsolete collection of objects providing management of general B-RAS functions for RADIUS Clients. This group became obsolete when objects for PPPoE Nas-Port format were added.
juniRadiusAuthClientGroup3	1.3.6.1.4.1.4874.2.2.19.2.2.18			A collection of objects providing management of RADIUS Authentication Clients.
juniRadiusAcctClientGroup3	1.3.6.1.4.1.4874.2.2.19.2.2.19			Obsolete collection of objects providing management of RADIUS Accounting Clients. This group became obsolete when reject counters were added.
juniRadiusAuthNotificationGroup2	1.3.6.1.4.1.4874.2.2.19.2.2.20			Management notifications for RADUIS authentication events.
juniRadiusAcctNotificationGroup2	1.3.6.1.4.1.4874.2.2.19.2.2.21			Management notifications for RADUIS accounting events.
juniRadiusBrasClientGroup7	1.3.6.1.4.1.4874.2.2.19.2.2.22			Obsolete collection of objects providing management of general B-RAS functions for RADIUS Clients. This group became obsolete when an object for VLAN Nas-Port format was added.
juniRadiusAcctClientGroup4	1.3.6.1.4.1.4874.2.2.19.2.2.23			A collection of objects providing management of RADIUS Accounting Clients.
juniRadiusBrasClientGroup8	1.3.6.1.4.1.4874.2.2.19.2.2.24			Obsolete collection of objects providing management of general B-RAS functions for RADIUS Clients. This group became obsolete when new objects were added to indicate which RADIUS attributes should be included or excluded from RADIUS packets.
juniRadiusBrasClientGroup9	1.3.6.1.4.1.4874.2.2.19.2.2.25			A collection of objects providing management of general B-RAS functions for RADIUS Clients.
juniRadiusBrasClientGroup10	1.3.6.1.4.1.4874.2.2.19.2.2.26			A collection of objects providing management of general B-RAS functions for RADIUS Clients. This group became obsolete when new objects were added to enable/disable the overriding of the nas-port-id and/or calling-station-id values with the PPPoE Remote Circuit Id.
juniRadiusBrasClientGroup11	1.3.6.1.4.1.4874.2.2.19.2.2.27			Obsolete collection of objects providing management of general B-RAS functions for RADIUS Clients.
juniRadiusBrasClientGroup12	1.3.6.1.4.1.4874.2.2.19.2.2.28			A collection of objects providing management of general B-RAS functions for RADIUS Clients.
juniRadiusBrasClientGroup13	1.3.6.1.4.1.4874.2.2.19.2.2.29			A collection of objects providing management of general B-RAS functions for RADIUS Clients.
juniRadiusBrasClientGroup14	1.3.6.1.4.1.4874.2.2.19.2.2.30			A collection of objects providing management of general B-RAS functions for RADIUS Clients.
juniRadiusBrasClientGroup15	1.3.6.1.4.1.4874.2.2.19.2.2.31			A collection of objects providing management of general B-RAS functions for RADIUS Clients.
juniRadiusBrasClientGroup16	1.3.6.1.4.1.4874.2.2.19.2.2.32			A collection of objects providing management of general B-RAS functions for RADIUS Clients.
juniRadiusBrasClientGroup17	1.3.6.1.4.1.4874.2.2.19.2.2.33			A collection of objects providing management of general B-RAS functions for RADIUS Clients.
juniRadiusBrasClientGroup18	1.3.6.1.4.1.4874.2.2.19.2.2.34			A collection of objects providing management of general B-RAS functions for RADIUS Clients.
juniRadiusBrasClientGroup19	1.3.6.1.4.1.4874.2.2.19.2.2.35			A collection of objects providing management of general B-RAS functions for RADIUS Clients.
juniRadiusBrasClientGroup20	1.3.6.1.4.1.4874.2.2.19.2.2.36			A collection of objects providing management of general B-RAS functions for RADIUS Clients.
juniRadiusClientTraps	1.3.6.1.4.1.4874.2.2.19.3
juniRadiusClientTrapPrefix	1.3.6.1.4.1.4874.2.2.19.3.0
NTF juniRadiusAuthClientServerUnavailable	1.3.6.1.4.1.4874.2.2.19.3.0.1			This trap will be generated when the requested authentication server is not available.
NTF juniRadiusAuthClientNoServerAvailable	1.3.6.1.4.1.4874.2.2.19.3.0.2			This trap will be generated when all of the requested servers were not available.
NTF juniRadiusAcctClientServerUnavailable	1.3.6.1.4.1.4874.2.2.19.3.0.3			This trap will be generated when the requested accounting server is not available.
NTF juniRadiusAcctClientNoServerAvailable	1.3.6.1.4.1.4874.2.2.19.3.0.4			This trap will be generated when all of the requested servers were not available.
NTF juniRadiusAuthClientServerAvailable	1.3.6.1.4.1.4874.2.2.19.3.0.5			This trap will be generated when the requested authentication server becomes available again after a period of time.
NTF juniRadiusAcctClientServerAvailable	1.3.6.1.4.1.4874.2.2.19.3.0.6			This trap will be generated when the requested accounting server becomes available again after a period of time.
juniRadiusClientTrapControl	1.3.6.1.4.1.4874.2.2.19.4
IP juniRadiusAuthClientUnavailableServer	1.3.6.1.4.1.4874.2.2.19.4.1	IpAddress	accessible-for-notify	The IP address of the RADIUS client's former authentication server that is no longer available. The value of this object is equivalent to the prior value of juniRadiusAuthClientCfgServerAddress.
IP juniRadiusAuthClientNextAvailableServer	1.3.6.1.4.1.4874.2.2.19.4.2	IpAddress	accessible-for-notify	The next available RADIUS authentication server, replacing the one that is unavailable. The value of this object is equivalent to the current value of juniRadiusAuthClientCfgServerAddress.
IP juniRadiusAcctClientUnavailableServer	1.3.6.1.4.1.4874.2.2.19.4.3	IpAddress	accessible-for-notify	The IP address of the RADIUS client's former accounting server that is no longer available. The value of this object is equivalent to the prior value of juniRadiusAcctClientCfgServerAddress.
IP juniRadiusAcctClientNextAvailableServer	1.3.6.1.4.1.4874.2.2.19.4.4	IpAddress	accessible-for-notify	The next available RADIUS accounting server, replacing the one that is unavailable. The value of this object is equivalent to the current value of juniRadiusAcctClientCfgServerAddress.
IP juniRadiusAuthClientAvailableServer	1.3.6.1.4.1.4874.2.2.19.4.5	IpAddress	accessible-for-notify	The re-available RADIUS authentication server after a period of time called dead-time. The value of this object is equivalent to the current value of juniRadiusAuthClientCfgServerAddress.
IP juniRadiusAcctClientAvailableServer	1.3.6.1.4.1.4874.2.2.19.4.6	IpAddress	accessible-for-notify	The re-available RADIUS accounting server after a period of time called dead-time. The value of this object is equivalent to the current value of juniRadiusAcctClientCfgServerAddress.

RFC description

Manages RADIUS client configuration for authentication, accounting, and IPv6 attributes on Juniper devices.

Start monitoring Juniper Networks E-series (ERX) edge router (RADIUS client configuration) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Juniper-RADIUS-CLIENT-MIB