All MIBs › Juniper-QoS-MIB
Organization: Juniper Networks, Inc.
Last Updated: 2005-07-06
Category: Quality of Service, Vendor: Juniper
Description: Juniper Networks MIB for managing and monitoring QoS policies, queues, and traffic shaping parameters on Juniper E-series routers.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is Juniper-QoS-MIB?
Juniper-QoS-MIB is a Juniper Networks enterprise MIB for managing and monitoring Quality of Service policies, queues, schedulers, and traffic shaping on E-series routers. It primarily exposes configuration and capacity data: maximum traffic classes, queue lengths, scheduler burst sizes, and counts of configured QoS profiles, drop profiles, and interfaces using QoS. Its monitoring value is largely capacity/utilization-oriented rather than fault-oriented, letting an operator track how many QoS profiles, queues, and interfaces are provisioned against platform maximums (juniQosMaxTrafficClass, juniQosMaxQueueLength) to catch approaching resource exhaustion before it causes traffic problems. It is a self-contained enterprise MIB but conceptually aligns with generic QoS/DiffServ concepts found in IETF DIFFSERV-MIB style modules. It is deployed on Juniper E-series broadband edge routers enforcing per-subscriber or per-service traffic shaping and prioritization. Engineers can download the Juniper-QoS-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in Juniper-QoS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Juniper Networks E-series broadband routers
Monitoring Examples
An operator would poll juniQosProfileCount and juniQosInterfaceCount to track how many QoS profiles and QoS-enabled interfaces are currently active, comparing against juniQosMaxQosProfileRules to see how close the router is to its configured limits. juniQosQueueProfileCount and juniQosSchedulerProfileCount would be checked together to verify queue and scheduler provisioning matches expected service design. A rising juniQosDropProfileCount alongside falling available headroom could prompt review of shaping policy before congestion-related drops increase.
What Can Be Monitored
- configured QoS profile count
- queue and scheduler profile counts
- QoS-enabled interface count
- drop profile count
- maximum traffic classes/queue length
- scheduler burst size limits
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| ifIndex | OBJECT-TYPE |
From Juniper-MIBs
| juniMibs | MODULE-IDENTITY |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter64 | |
| Gauge32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| juniQos | 1.3.6.1.4.1.4874.2.2.57.1.2 | |||
| U32 juniQosAtmVpAtmPath | 1.3.6.1.4.1.4874.2.2.57.1.14.3 | Unsigned32 | read-write | This object is the ATM VP which correlates to the ATM VP UID object. |
| U32 juniQosAtmVpAtmPortInterfaceUid | 1.3.6.1.4.1.4874.2.2.57.1.14.2 | Unsigned32 | read-write | This object is the ATM port interface UID which correlates to the ATM VP UID object. |
| U32 juniQosAtmVpUid | 1.3.6.1.4.1.4874.2.2.57.1.14.4 | Unsigned32 | read-write | This object is the ATM VP UID which correlates to the ATM port interface and path objects. |
| juniQosAtmVpUidSupport | 1.3.6.1.4.1.4874.2.2.57.1.14 | |||
| juniQosAtmVpUidSupportGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.15 | This group defines QoS ATM VP UID support. | ||
| INT juniQosAtmVpUidValid | 1.3.6.1.4.1.4874.2.2.57.1.14.1 | INTEGER | read-only | This object reflects the status of the ATM VP UID translation objects. |
| juniQosCapability | 1.3.6.1.4.1.4874.2.2.57.1.1 | |||
| juniQosCapabilityGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.1 | This group defines QoS application-wide capabilities management. | ||
| juniQosCompliance | 1.3.6.1.4.1.4874.2.2.57.2.1.1 | Obsolete compliance statement for entities which implement the Juniper QoS management MIB. This statement became obsolete when drop profile list support was added. | ||
| juniQosCompliance2 | 1.3.6.1.4.1.4874.2.2.57.2.1.2 | Obsolete compliance statement for entities which implement the Juniper QoS management MIB. This statement became obsolete when ATM VP UID, statistics profile list and QoS mode port support was added. | ||
| juniQosCompliance3 | 1.3.6.1.4.1.4874.2.2.57.2.1.3 | Obsolete compliance statement for entities which implement the Juniper QoS management MIB. This statement became obsolete when multiple traffic class group support was added. | ||
| juniQosCompliance4 | 1.3.6.1.4.1.4874.2.2.57.2.1.4 | The compliance statement for entities which implement the Juniper QoS management MIB. | ||
| juniQosCompliance5 | 1.3.6.1.4.1.4874.2.2.57.2.1.5 | The compliance statement for entities which implement the Juniper QoS management MIB. | ||
| juniQosCompliance6 | 1.3.6.1.4.1.4874.2.2.57.2.1.6 | The compliance statement for entities which implement the Juniper QoS management MIB. | ||
| juniQosCompliances | 1.3.6.1.4.1.4874.2.2.57.2.1 | |||
| juniQosConformance | 1.3.6.1.4.1.4874.2.2.57.2 | |||
| U32 juniQosDropProfileAverageLengthExponent | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.4 | Unsigned32 | read-create | Specifies the exponent used to weight the average queue length over time, controlling RED responsiveness. A non-default value enables the average queue length calculation. |
| U32 juniQosDropProfileCommittedThresholdMaxDropProbability | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.8 | Unsigned32 | read-create | Specifies the maximum drop probability for committed traffic. |
| U32 juniQosDropProfileCommittedThresholdMaxThreshold | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.7 | Unsigned32 | read-create | Specifies the maximum drop threshold for committed traffic. The units are defined by juniQosDropProfileCommittedThresholdUnits. If units are bytes, the value must be in the range of 0..1073741824. If units are percent, the value must be in the range of 1..100. Setting the minimum and maximum thresholds to 0 disables the threshold. |
| U32 juniQosDropProfileCommittedThresholdMinThreshold | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.6 | Unsigned32 | read-create | Specifies the minimum drop threshold for committed traffic. The units are defined by juniQosDropProfileCommittedThresholdUnits. If units are bytes, the value must be in the range of 0..1073741824. If units are percent, the value must be in the range of 1..100. |
| INT juniQosDropProfileCommittedThresholdUnits | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.5 | INTEGER | read-create | Specifies the units for the committed minimum and maximum thresholds. |
| U32 juniQosDropProfileConformedThresholdMaxDropProbability | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.12 | Unsigned32 | read-create | Specifies the maximum drop probability for conformed traffic. |
| U32 juniQosDropProfileConformedThresholdMaxThreshold | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.11 | Unsigned32 | read-create | Specifies the maximum drop threshold for conformed traffic. The units are defined by juniQosDropProfileConformedThresholdUnits. If units are bytes, the value must be in the range of 0..1073741824. If units are percent, the value must be in the range of 1..100. Setting the minimum and maximum thresholds to 0 disables the threshold. |
| U32 juniQosDropProfileConformedThresholdMinThreshold | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.10 | Unsigned32 | read-create | Specifies the minimum drop threshold for conformed traffic. The units are defined by juniQosDropProfileConformedThresholdUnits. If units are bytes, the value must be in the range of 0..1073741824. If units are percent, the value must be in the range of 1..100. |
| INT juniQosDropProfileConformedThresholdUnits | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.9 | INTEGER | read-create | Specifies the units for the conformed minimum and maximum thresholds. |
| G32 juniQosDropProfileCount | 1.3.6.1.4.1.4874.2.2.57.1.2.7 | Gauge32 | read-only | This object reflects the number of configured drop profiles. |
| juniQosDropProfileEntry | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1 | not-accessible | Each entry describes the characteristics of a drop profile element. | |
| U32 juniQosDropProfileExceededThresholdMaxDropProbability | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.16 | Unsigned32 | read-create | Specifies the maximum drop probability for exceeded traffic. |
| U32 juniQosDropProfileExceededThresholdMaxThreshold | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.15 | Unsigned32 | read-create | Specifies the maximum drop threshold for exceeded traffic. The units are defined by juniQosDropProfileExceededThresholdUnits. If units are bytes, the value must be in the range of 0..1073741824. If units are percent, the value must be in the range of 1..100. Setting the minimum and maximum thresholds to 0 disables the threshold. |
| U32 juniQosDropProfileExceededThresholdMinThreshold | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.14 | Unsigned32 | read-create | Specifies the minimum drop threshold for exceeded traffic. The units are defined by juniQosDropProfileExceededThresholdUnits. If units are bytes, the value must be in the range of 0..1073741824. If units are percent, the value must be in the range of 1..100. |
| INT juniQosDropProfileExceededThresholdUnits | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.13 | INTEGER | read-create | Specifies the units for the exceeded minimum and maximum thresholds. |
| U32 juniQosDropProfileIndex | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.1 | Unsigned32 | not-accessible | The number of the drop profile entry which is defined by this row. |
| T/F juniQosDropProfileIsReferencedByQosProfile | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.19 | TruthValue | read-only | True if the drop profile is referenced by QoS profile(s). |
| juniQosDropProfileList | 1.3.6.1.4.1.4874.2.2.57.1.13 | |||
| juniQosDropProfileListGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.14 | This group defines QoS drop profile management. | ||
| STR juniQosDropProfileName | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.3 | DisplayString | read-create | Specifies the name of the drop profile defined by this row. |
| U32 juniQosDropProfileNextIndex | 1.3.6.1.4.1.4874.2.2.57.1.13.1 | Unsigned32 | read-only | This scalar object returns the index of the next available row in the juniQosDropProfileTable. |
| ROW juniQosDropProfileRowStatus | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.2 | RowStatus | read-create | Controls creation/deletion of conceptual rows within this table. All rowStatus modes are supported. To create an entry in this table, the following entry objects MUST be explicitly configured: juniQosDropProfileRowStatus juniQosDropProfileName |
| juniQosDropProfileTable | 1.3.6.1.4.1.4874.2.2.57.1.13.2 | not-accessible | This table contains entries for elements of drop profile definitions. | |
| T/F juniQosDropProfileUpdateNow | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.18 | TruthValue | read-create | When set to true, modifications made to the drop profile object will be committed to the line cards. |
| T/F juniQosDropProfileUpdatePending | 1.3.6.1.4.1.4874.2.2.57.1.13.2.1.17 | TruthValue | read-only | True if modifications have been made to the drop profile object which have not been committed to the line cards. |
| juniQosGroups | 1.3.6.1.4.1.4874.2.2.57.2.2 | |||
| juniQosIfAttach | 1.3.6.1.4.1.4874.2.2.57.1.10 | |||
| juniQosIfAttachEntry | 1.3.6.1.4.1.4874.2.2.57.1.10.1.1 | not-accessible | Each entry contains the attachment of QoS to an interface. | |
| juniQosIfAttachGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.9 | This group defines QoS interface attachment management. | ||
| U32 juniQosIfAttachIndex | 1.3.6.1.4.1.4874.2.2.57.1.10.1.1.1 | Unsigned32 | not-accessible | The interface number representing the interface to which QoS has been attached. |
| U32 juniQosIfAttachQosProfileIndex | 1.3.6.1.4.1.4874.2.2.57.1.10.1.1.3 | Unsigned32 | read-create | The QoS profile attached to this interface. |
| ROW juniQosIfAttachRowStatus | 1.3.6.1.4.1.4874.2.2.57.1.10.1.1.2 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy juniQosIfAttachQosProfileIndex must be specified when creating the row. *** LIMITED ACCESS LIST CONFIGURATION LEVEL *** RowStatus createAndGo/destroy operations have the following special-purpose semantics: createAndGo Create an entry having the specified configuration and append it to the target list. destroy Destroy the specified list and all of its constituent elements. |
| juniQosIfAttachTable | 1.3.6.1.4.1.4874.2.2.57.1.10.1 | not-accessible | This table contains entries which represent attachment of QoS to interfaces. | |
| G32 juniQosInterfaceCount | 1.3.6.1.4.1.4874.2.2.57.1.2.5 | Gauge32 | read-only | This object reflects the number of configured interface QoS attachments. |
| INT juniQosInterfaceType | 1.3.6.1.4.1.4874.2.2.57.1.9.1.1.4 | INTEGER | not-accessible | The QoS interface type ID, part of the index for juniQosProfileElementTable. Please note that if the juniQpsProfileEntryType is trafficClassGroup, then only ethernet, atm, serial, and serverPort are valid interface types. |
| U32 juniQosMaxQosProfileRules | 1.3.6.1.4.1.4874.2.2.57.1.1.5 | Unsigned32 | read-only | This object reflects the maximum number of rules per qos-profile supported. |
| U32 juniQosMaxQueueLength | 1.3.6.1.4.1.4874.2.2.57.1.1.2 | Unsigned32 | read-only | This object reflects the maximum supported queue length in bytes. |
| U32 juniQosMaxSchedulerBurst | 1.3.6.1.4.1.4874.2.2.57.1.1.4 | Unsigned32 | read-only | This object reflects the maximum supported scheduler burst size in bytes. |
| U32 juniQosMaxTrafficClass | 1.3.6.1.4.1.4874.2.2.57.1.1.1 | Unsigned32 | read-only | This object reflects the maximum number of traffic classes supported. |
| juniQosMIB | 1.3.6.1.4.1.4874.2.2.57 | The Quality of Service (QoS) MIB for the Juniper Networks enterprise. | ||
| U32 juniQosMinSchedulerBurst | 1.3.6.1.4.1.4874.2.2.57.1.1.3 | Unsigned32 | read-only | This object reflects the minimum supported scheduler burst size in bytes. |
| juniQosObjects | 1.3.6.1.4.1.4874.2.2.57.1 | |||
| C64 juniQosOutBytesForwarded | 1.3.6.1.4.1.4874.2.2.57.1.12.1.1.2 | Counter64 | read-only | The number of bytes queued on this interface. |
| C64 juniQosOutGreenBytesSchedulerDrops | 1.3.6.1.4.1.4874.2.2.57.1.12.1.1.6 | Counter64 | read-only | The number of green bytes dropped on this interface. |
| C64 juniQosOutGreenPacketsSchedulerDrops | 1.3.6.1.4.1.4874.2.2.57.1.12.1.1.3 | Counter64 | read-only | The number of green packets dropped on this interface. |
| C64 juniQosOutPacketForwarded | 1.3.6.1.4.1.4874.2.2.57.1.12.1.1.1 | Counter64 | read-only | The number of packets queued on this interface. |
| C64 juniQosOutRedBytesSchedulerDrops | 1.3.6.1.4.1.4874.2.2.57.1.12.1.1.8 | Counter64 | read-only | The number of red bytes dropped on this interface. |
| C64 juniQosOutRedPacketsSchedulerDrops | 1.3.6.1.4.1.4874.2.2.57.1.12.1.1.5 | Counter64 | read-only | The number of red packets dropped on this interface. |
| C64 juniQosOutYellowBytesSchedulerDrops | 1.3.6.1.4.1.4874.2.2.57.1.12.1.1.7 | Counter64 | read-only | The number of yellow bytes dropped on this interface. |
| C64 juniQosOutYellowPacketsSchedulerDrops | 1.3.6.1.4.1.4874.2.2.57.1.12.1.1.4 | Counter64 | read-only | The number of yellow packets dropped on this interface. |
| juniQosProfile | 1.3.6.1.4.1.4874.2.2.57.1.8 | |||
| G32 juniQosProfileCount | 1.3.6.1.4.1.4874.2.2.57.1.2.4 | Gauge32 | read-only | This object reflects the number of configured QoS profiles. |
| juniQosProfileElement | 1.3.6.1.4.1.4874.2.2.57.1.9 | |||
| juniQosProfileElementEntry | 1.3.6.1.4.1.4874.2.2.57.1.9.1.1 | not-accessible | Each entry describes the characteristics of a QoS profile element. | |
| U32 juniQosProfileElementEntryDropProfile | 1.3.6.1.4.1.4874.2.2.57.1.9.1.1.6 | Unsigned32 | read-create | Specifies the drop profile assigned to the QoS entry. |
| U32 juniQosProfileElementEntryQueueProfile | 1.3.6.1.4.1.4874.2.2.57.1.9.1.1.2 | Unsigned32 | read-create | Specifies the queue profile assigned to the QoS entry. |
| ROW juniQosProfileElementEntryRowStatus | 1.3.6.1.4.1.4874.2.2.57.1.9.1.1.1 | RowStatus | read-create | Controls creation/deletion of conceptual rows within this table. All rowStatus modes are supported. To create an entry in this table, the following entry object MUST be explicitly configured: juniQosProfileRowStatus |
| U32 juniQosProfileElementEntrySchedulerProfile | 1.3.6.1.4.1.4874.2.2.57.1.9.1.1.3 | Unsigned32 | read-create | Specifies the scheduler profile assigned to the QoS entry. |
| U32 juniQosProfileElementEntryStatisticsProfile | 1.3.6.1.4.1.4874.2.2.57.1.9.1.1.7 | Unsigned32 | read-create | Specifies the statistics profile assigned to the QoS entry. |
| juniQosProfileElementGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.8 | This obsolete group defines QoS profile element entry management. This group became obsolete when drop profile list support was added. | ||
| juniQosProfileElementGroup2 | 1.3.6.1.4.1.4874.2.2.57.2.2.13 | This obsolete group defines QoS profile element entry management. This group became obsolete when statistics profile list support was added. | ||
| juniQosProfileElementGroup3 | 1.3.6.1.4.1.4874.2.2.57.2.2.17 | This group defines QoS profile element entry management. | ||
| juniQosProfileElementTable | 1.3.6.1.4.1.4874.2.2.57.1.9.1 | not-accessible | This table contains entries for elements of QoS profile definitions. | |
| juniQosProfileEntry | 1.3.6.1.4.1.4874.2.2.57.1.8.2.1 | not-accessible | Each entry describes the characteristics of a QoS profile element. | |
| INT juniQosProfileEntryType | 1.3.6.1.4.1.4874.2.2.57.1.9.1.1.5 | INTEGER | not-accessible | The QoS profile type, part of the index for juniQosProfileElementTable. |
| U32 juniQosProfileIndex | 1.3.6.1.4.1.4874.2.2.57.1.8.2.1.1 | Unsigned32 | not-accessible | The number identifies this QoS profile. |
| T/F juniQosProfileIsReferencedByInterfaceQosAttachment | 1.3.6.1.4.1.4874.2.2.57.1.8.2.1.6 | TruthValue | read-only | When true, the QoS profile is referenced by an interface QoS attachment. |
| T/F juniQosProfileIsReferencedByQosPortTypeProfile | 1.3.6.1.4.1.4874.2.2.57.1.8.2.1.7 | TruthValue | read-only | When true, the QoS profile is referenced by a QoS port type profile. |
| juniQosProfileListGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.7 | This group defines QoS profile management. | ||
| STR juniQosProfileName | 1.3.6.1.4.1.4874.2.2.57.1.8.2.1.3 | DisplayString | read-create | Specifies the name of the QoS profile defined by this row. |
| U32 juniQosProfileNextIndex | 1.3.6.1.4.1.4874.2.2.57.1.8.1 | Unsigned32 | read-only | This scalar object returns the index of the next available row in the juniQosProfileTable. |
| ROW juniQosProfileRowStatus | 1.3.6.1.4.1.4874.2.2.57.1.8.2.1.2 | RowStatus | read-create | Controls creation/deletion of conceptual rows within this table. All rowStatus modes are supported. To create a QoS profile in this table, the following entry objects MUST be explicitly configured: juniQosProfileRowStatus juniQosProfileName |
| juniQosProfileTable | 1.3.6.1.4.1.4874.2.2.57.1.8.2 | not-accessible | This table contains entries for elements of QoS Profile definitions. | |
| T/F juniQosProfileUpdateNow | 1.3.6.1.4.1.4874.2.2.57.1.8.2.1.5 | TruthValue | read-create | When set to true, modifications made to the QoS profile object will be committed to the line cards. |
| T/F juniQosProfileUpdatePending | 1.3.6.1.4.1.4874.2.2.57.1.8.2.1.4 | TruthValue | read-only | True if modifications have been made to the QoS profile object which have not been committed to the line cards. |
| juniQosQosModePortEntry | 1.3.6.1.4.1.4874.2.2.57.1.16.1.1 | not-accessible | Each entry describes the characteristics of a QoS mode port element. | |
| INT juniQosQosModePortFrameMode | 1.3.6.1.4.1.4874.2.2.57.1.16.1.1.3 | INTEGER | read-create | Specifies the frame mode for this ATM port interface. lowCdv mode can not be configured unless juniQosQosShapingModeShapingMode for the ATM port interface is configured as 'cell'. |
| juniQosQosModePortGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.20 | This group defines QoS mode port management. | ||
| U32 juniQosQosModePortIndex | 1.3.6.1.4.1.4874.2.2.57.1.16.1.1.1 | Unsigned32 | not-accessible | The ATM port interface for which this row defines QoS mode port settings. |
| juniQosQosModePortList | 1.3.6.1.4.1.4874.2.2.57.1.16 | |||
| ROW juniQosQosModePortRowStatus | 1.3.6.1.4.1.4874.2.2.57.1.16.1.1.2 | RowStatus | read-create | Controls creation/deletion of conceptual rows within this table. All rowStatus modes are supported. To create an entry in this table, the following entry objects MUST be explicitly configured: juniQosQosModePortRowStatus juniQosQosModePortFrameMode |
| juniQosQosModePortTable | 1.3.6.1.4.1.4874.2.2.57.1.16.1 | not-accessible | This table contains entries for elements of QoS mode port definitions. | |
| juniQosQosPortTypeProfile | 1.3.6.1.4.1.4874.2.2.57.1.11 | |||
| G32 juniQosQosPortTypeProfileCount | 1.3.6.1.4.1.4874.2.2.57.1.2.6 | Gauge32 | read-only | This object reflects the number of configured default port profiles. |
| juniQosQosPortTypeProfileEntry | 1.3.6.1.4.1.4874.2.2.57.1.11.1.1 | not-accessible | Each entry contains the attachment of QoS to an interface. | |
| juniQosQosPortTypeProfileGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.10 | This group defines QoS default port profile management. | ||
| INT juniQosQosPortTypeProfileIndex | 1.3.6.1.4.1.4874.2.2.57.1.11.1.1.1 | INTEGER | not-accessible | The interface number representing the types of interface to which QoS has been attached. |
| U32 juniQosQosPortTypeProfileQosProfileIndex | 1.3.6.1.4.1.4874.2.2.57.1.11.1.1.3 | Unsigned32 | read-create | The QoS profile assigned to this port type. |
| ROW juniQosQosPortTypeProfileRowStatus | 1.3.6.1.4.1.4874.2.2.57.1.11.1.1.2 | RowStatus | read-create | Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy juniQosQosPortTypeProfileQosProfileIndex must be specified when creating the row. *** LIMITED ACCESS LIST CONFIGURATION LEVEL *** RowStatus createAndGo/destroy operations have the following special-purpose semantics: createAndGo Create an entry having the specified configuration and append it to the target list. destroy Destroy the specified list and all of its constituent elements. |
| juniQosQosPortTypeProfileTable | 1.3.6.1.4.1.4874.2.2.57.1.11.1 | not-accessible | This table contains entries which represent attachment of QoS to interface types with which they are associated. | |
| juniQosQosShapingModeEntry | 1.3.6.1.4.1.4874.2.2.57.1.17.1.1 | not-accessible | Each entry describes the characteristics of a QoS shaping mode element. | |
| juniQosQosShapingModeGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.21 | This group defines QoS shaping mode management. | ||
| U32 juniQosQosShapingModeIndex | 1.3.6.1.4.1.4874.2.2.57.1.17.1.1.1 | Unsigned32 | not-accessible | The ATM port interface for which this row defines QoS shaping mode port settings. |
| juniQosQosShapingModeList | 1.3.6.1.4.1.4874.2.2.57.1.17 | |||
| ROW juniQosQosShapingModeRowStatus | 1.3.6.1.4.1.4874.2.2.57.1.17.1.1.2 | RowStatus | read-create | Controls creation/deletion of conceptual rows within this table. All rowStatus modes are supported. To create an entry in this table, the following entry objects MUST be explicitly configured: juniQosQosShapingModeRowStatus juniQosQosShapingModeShapingMode |
| INT juniQosQosShapingModeShapingMode | 1.3.6.1.4.1.4874.2.2.57.1.17.1.1.3 | INTEGER | read-create | Specifies the QoS shaping mode for this ATM port interface. 'frame' indicates shaping is to be based on frames, not including cell encapsulation and padding. 'cell' indicates shaping is to be based on cells, with cell encapsulation and padding included. 'frame' mode can not be configured unless juniQosQosModePortFrameMode for the ATM port interface is configured as 'lowLatency'. |
| juniQosQosShapingModeTable | 1.3.6.1.4.1.4874.2.2.57.1.17.1 | not-accessible | This table contains entries for elements of QoS shaping mode definitions. | |
| U32 juniQosQueueProfileBufferWeight | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.18 | Unsigned32 | read-create | The relative weight for queues in this traffic class. |
| U32 juniQosQueueProfileCommittedDropRate | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.13 | Unsigned32 | read-create | Specifies the drop rate (percent of traffic) for committed traffic. |
| U32 juniQosQueueProfileCommittedDropThreshold | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.12 | Unsigned32 | read-create | Specifies the drop threshold (percent of queue) for committed traffic. |
| U32 juniQosQueueProfileCommittedMaxLength | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.5 | Unsigned32 | read-create | Specifies the maximum queue length in bytes for committed traffic. |
| U32 juniQosQueueProfileCommittedMinLength | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.4 | Unsigned32 | read-create | Specifies the minimum queue length in bytes for committed traffic. |
| U32 juniQosQueueProfileConformedDropRate | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.15 | Unsigned32 | read-create | Specifies the drop rate (percent of traffic) for comformed traffic. |
| U32 juniQosQueueProfileConformedDropThreshold | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.14 | Unsigned32 | read-create | Specifies the drop threshold (percent of queue) for comformed traffic. |
| U32 juniQosQueueProfileConformedFraction | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.10 | Unsigned32 | read-create | Specifies the maximum percentage of queue occupied by conformed traffic. |
| U32 juniQosQueueProfileConformedMaxLength | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.7 | Unsigned32 | read-create | Specifies the maximum queue length in bytes for conformed traffic. |
| U32 juniQosQueueProfileConformedMinLength | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.6 | Unsigned32 | read-create | Specifies the minimum queue length in bytes for conformed traffic. |
| G32 juniQosQueueProfileCount | 1.3.6.1.4.1.4874.2.2.57.1.2.2 | Gauge32 | read-only | This object reflects the number of configured queue profiles. |
| juniQosQueueProfileEntry | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1 | not-accessible | Each entry describes the characteristics of a queue profile element. | |
| U32 juniQosQueueProfileExceededDropRate | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.17 | Unsigned32 | read-create | Specifies the drop rate (percent of traffic) for exceeded traffic. |
| U32 juniQosQueueProfileExceededDropThreshold | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.16 | Unsigned32 | read-create | Specifies the drop threshold (percent of queue) for exceeded traffic. |
| U32 juniQosQueueProfileExceededFraction | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.11 | Unsigned32 | read-create | Specifies the maximum percentage of queue occupied by exceeded traffic. |
| U32 juniQosQueueProfileExceededMaxLength | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.9 | Unsigned32 | read-create | Specifies the maximum queue length in bytes for exceeded traffic. |
| U32 juniQosQueueProfileExceededMinLength | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.8 | Unsigned32 | read-create | Specifies the minimum queue length in bytes for exceeded traffic. |
| U32 juniQosQueueProfileIndex | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.1 | Unsigned32 | not-accessible | The number of the queue profile entry which is defined by this row. |
| T/F juniQosQueueProfileIsReferencedByQosProfile | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.21 | TruthValue | read-only | When true, the queue profile is referenced by a QoS profile. |
| juniQosQueueProfileList | 1.3.6.1.4.1.4874.2.2.57.1.7 | |||
| juniQosQueueProfileListGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.5 | This group defines QoS queue profile management. | ||
| STR juniQosQueueProfileName | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.3 | DisplayString | read-create | Specifies the name of the queue profile defined by this row. |
| U32 juniQosQueueProfileNextIndex | 1.3.6.1.4.1.4874.2.2.57.1.7.1 | Unsigned32 | read-only | This scalar object returns the index of the next available row in the juniQosQueueProfileTable. |
| ROW juniQosQueueProfileRowStatus | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.2 | RowStatus | read-create | Controls creation/deletion of conceptual rows within this table. All rowStatus modes are supported. To create an entry in this table, the following entry objects MUST be explicitly configured: juniQosQueueProfileRowStatus juniQosQueueProfileName |
| juniQosQueueProfileTable | 1.3.6.1.4.1.4874.2.2.57.1.7.2 | not-accessible | This table contains entries for elements of queue profile definitions. | |
| T/F juniQosQueueProfileUpdateNow | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.20 | TruthValue | read-create | When set to true, modifications made to the queue profile object will be committed to the line cards. |
| T/F juniQosQueueProfileUpdatePending | 1.3.6.1.4.1.4874.2.2.57.1.7.2.1.19 | TruthValue | read-only | True if modifications have been made to the queue profile object which have not been committed to the line cards. |
| juniQosQueueStatistics | 1.3.6.1.4.1.4874.2.2.57.1.12 | |||
| juniQosQueueStatisticsEntry | 1.3.6.1.4.1.4874.2.2.57.1.12.1.1 | not-accessible | Each entry defines a single queue statistics entry. | |
| juniQosQueueStatisticsGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.11 | This group defines QoS queue statistics reporting. | ||
| juniQosQueueStatisticsTable | 1.3.6.1.4.1.4874.2.2.57.1.12.1 | not-accessible | Each entry within this table contains queue statistics for an interface/traffic class combination. | |
| juniQosScalarGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.2 | This obsolete group defines QoS application-wide counters. This group became obsolete when drop profile list support was added. | ||
| juniQosScalarGroup2 | 1.3.6.1.4.1.4874.2.2.57.2.2.12 | This obsolete group defines QoS application-wide counters. This group became obsolete when statistics profile list support was added. | ||
| juniQosScalarGroup3 | 1.3.6.1.4.1.4874.2.2.57.2.2.16 | This group defines QoS application-wide counters. | ||
| U32 juniQosSchedulerProfileAssuredRate | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1.11 | Unsigned32 | read-create | Specifies the assured rate in bits per second (bps). When this object has a non-default value, the scheduler weight (juniQosSchedulerProfileWeight) is ignored. A value of '4294967295' configures Hierarchical Assured Rate. |
| U32 juniQosSchedulerProfileBurst | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1.5 | Unsigned32 | read-create | Specifies the catch-up burst size in bytes. Burst value of 0 indicates the largest burst size the system will allow without losing accuracy. |
| G32 juniQosSchedulerProfileCount | 1.3.6.1.4.1.4874.2.2.57.1.2.3 | Gauge32 | read-only | This object reflects the number of configured scheduler profiles. |
| juniQosSchedulerProfileEntry | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1 | not-accessible | Each entry describes the characteristics of a scheduler profile element. | |
| U32 juniQosSchedulerProfileIndex | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1.1 | Unsigned32 | not-accessible | The number of the scheduler profile entry which is defined by this row. |
| T/F juniQosSchedulerProfileIsReferencedByQosProfile | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1.10 | TruthValue | read-only | When true, the scheduler profile is referenced by a QoS profile. |
| juniQosSchedulerProfileList | 1.3.6.1.4.1.4874.2.2.57.1.6 | |||
| juniQosSchedulerProfileListGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.6 | This obsolete group defines QoS scheduler profile management. This group became obsolete when assured rate support was added. | ||
| juniQosSchedulerProfileListGroup2 | 1.3.6.1.4.1.4874.2.2.57.2.2.19 | This group defines QoS scheduler profile management. | ||
| juniQosSchedulerProfileListGroup3 | 1.3.6.1.4.1.4874.2.2.57.2.2.23 | This group defines QoS scheduler profile management. | ||
| juniQosSchedulerProfileListGroup4 | 1.3.6.1.4.1.4874.2.2.57.2.2.24 | This group defines QoS scheduler profile management. | ||
| STR juniQosSchedulerProfileName | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1.3 | DisplayString | read-create | Specifies the name of the scheduler profile defined by this row. |
| U32 juniQosSchedulerProfileNextIndex | 1.3.6.1.4.1.4874.2.2.57.1.6.1 | Unsigned32 | read-only | This scalar object returns the index of the next available row in the juniQosSchedulerProfileTable. |
| ROW juniQosSchedulerProfileRowStatus | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1.2 | RowStatus | read-create | Controls creation/deletion of conceptual rows within this table. All rowStatus modes are supported. To create an entry in this table, the following entry objects MUST be explicitly configured: juniQosSchedulerProfileRowStatus juniQosSchedulerProfileName |
| U32 juniQosSchedulerProfileShapingRate | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1.4 | Unsigned32 | read-create | Specifies the shaping rate in bits per second (bps). Values between 1 and 63999 are not supported. |
| U32 juniQosSchedulerProfileSharedShapingBurstSize | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1.13 | Unsigned32 | read-create | Specifies the catch-up burst size for a shared shaping, in bytes. A value of zero indicates that the system should choose an appropriate default value. |
| T/F juniQosSchedulerProfileSharedShapingExplicitConstituents | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1.15 | TruthValue | read-create | This option allows automatic shared shaper constituent selecting and bandwidth allocation to be overridden. By default, constituents are configured implicitly. |
| I32 juniQosSchedulerProfileSharedShapingPriority | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1.16 | Integer32 | read-create | The priority of a strict shared shaper constituent. When the value of juniQosSchedulerProfileSharedShaper- ConstituentType is 'strict' the value of this object determines the order in which the strict constituent can claim bandwidth. Priority values range from 1 to 8, with priority 1 getting first claim amongst strict constituents on available shared bandwidth, and priority 8 getting final claim amongst strict constituents on available bandwidth. When two or more strict constituents have the same priority value, the rules used for implicit bandwidth allocation are applied to determine their order. A value of zero indicates 'not a constituent' of a shared shaper. A value of -1 indicates 'is a constituent' of a shared shaper, but the system is free to choose whether the constituent is 'strict-priority' of 'weighted' This object takes precedence over the juniQosSchedulerProfileSharedShapingWeight object. When set to a value from 1 to 8 the system sets the value of juniQosSchedulerProfileSharedShaping- Weight to zero. |
| U32 juniQosSchedulerProfileSharedShapingRate | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1.12 | Unsigned32 | read-create | Specifies the shared shaping rate in bits per second (bps). The range of 1 to 63999 is not supported. |
| INT juniQosSchedulerProfileSharedShapingType | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1.14 | INTEGER | read-create | The value of this object specifies the type of shared shaping that is to be performed when shared shaping is enabled. Shared shaper types are defined as follows: 'simple' indicates that Simple Shared Shaping is performed regardless of the line cards capabilities. 'compound' indicates that Compound Shared Shaping is to be performed. When compound is specified for a line card that does not support Compound Shared Shaping, a warning message is logged, and Simple Shared Shaping is configured instead. 'auto' indicates that selection of the shared shaper should be automatic such that compound shared shaping is performed on line cards which support it and simple shared shaping is performed on line cards that do not support it. |
| I32 juniQosSchedulerProfileSharedShapingWeight | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1.17 | Integer32 | read-create | The weight of a weighted shared shaper constituent. When the value of juniQosSchedulerProfileSharedShaper- ConstituentType is 'weighted' the value of this object determines the proportion of the weighted constituent's bandwidth Non-zero values specify the weight of a weighted shared shaping constituent. A value of zero indicates 'not a constituent' of a shared shaper. A value of -1 indicates 'is a constituent' of a shared shaper, but the system is free to choose whether the constituent is 'strict-priority' of 'weighted' The juniQosSchedulerProfileSharedShapingPriority has precedence over the this object. |
| T/F juniQosSchedulerProfileStrictPriority | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1.7 | TruthValue | read-create | Specifies the traffic to be dequeued before all other scheduler nodes. |
| juniQosSchedulerProfileTable | 1.3.6.1.4.1.4874.2.2.57.1.6.2 | not-accessible | This table contains entries for elements of Scheduler Profile definitions. | |
| T/F juniQosSchedulerProfileUpdateNow | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1.9 | TruthValue | read-create | When set to true, modifications made to the scheduler profile object will be committed to the line cards. |
| T/F juniQosSchedulerProfileUpdatePending | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1.8 | TruthValue | read-only | True if modifications have been made to the scheduler profile object which have not been committed to the line cards. |
| U32 juniQosSchedulerProfileWeight | 1.3.6.1.4.1.4874.2.2.57.1.6.2.1.6 | Unsigned32 | read-create | The relative weight of the scheduler. When an assured rate is specified, this object is ignored. |
| U32 juniQosStatisticsProfileCommittedDropThreshold | 1.3.6.1.4.1.4874.2.2.57.1.15.2.1.5 | Unsigned32 | read-create | Specifies the committed drop threshold. |
| U32 juniQosStatisticsProfileConformedDropThreshold | 1.3.6.1.4.1.4874.2.2.57.1.15.2.1.6 | Unsigned32 | read-create | Specifies the conformed drop threshold. |
| G32 juniQosStatisticsProfileCount | 1.3.6.1.4.1.4874.2.2.57.1.2.8 | Gauge32 | read-only | This object reflects the number of configured statistics profiles. |
| juniQosStatisticsProfileEntry | 1.3.6.1.4.1.4874.2.2.57.1.15.2.1 | not-accessible | Each entry describes the characteristics of a statstics profile element. | |
| U32 juniQosStatisticsProfileExceededDropThreshold | 1.3.6.1.4.1.4874.2.2.57.1.15.2.1.7 | Unsigned32 | read-create | Specifies the exceeded drop threshold. |
| U32 juniQosStatisticsProfileForwardingRateThreshold | 1.3.6.1.4.1.4874.2.2.57.1.15.2.1.4 | Unsigned32 | read-create | Specifies the forwarding rate threshold. |
| U32 juniQosStatisticsProfileIndex | 1.3.6.1.4.1.4874.2.2.57.1.15.2.1.1 | Unsigned32 | not-accessible | The number of the statistics profile entry which is defined by this row. |
| T/F juniQosStatisticsProfileIsReferencedByQosProfile | 1.3.6.1.4.1.4874.2.2.57.1.15.2.1.11 | TruthValue | read-only | True if the statistics profile is referenced by QoS profile(s). |
| juniQosStatisticsProfileList | 1.3.6.1.4.1.4874.2.2.57.1.15 | |||
| juniQosStatisticsProfileListGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.18 | This group defines QoS statistics profile management. | ||
| STR juniQosStatisticsProfileName | 1.3.6.1.4.1.4874.2.2.57.1.15.2.1.3 | DisplayString | read-create | Specifies the name of the statistics profile defined by this row. |
| U32 juniQosStatisticsProfileNextIndex | 1.3.6.1.4.1.4874.2.2.57.1.15.1 | Unsigned32 | read-only | This scalar object returns the index of the next available row in the juniQosStatsProfileTable. |
| U32 juniQosStatisticsProfileRatePeriod | 1.3.6.1.4.1.4874.2.2.57.1.15.2.1.8 | Unsigned32 | read-create | Specifies the rate period over which forwarding and drop thresholds are calculated |
| ROW juniQosStatisticsProfileRowStatus | 1.3.6.1.4.1.4874.2.2.57.1.15.2.1.2 | RowStatus | read-create | Controls creation/deletion of conceptual rows within this table. All rowStatus modes are supported. To create an entry in this table, the following entry objects MUST be explicitly configured: juniQosStatisticsProfileRowStatus juniQosStatisticsProfileName |
| juniQosStatisticsProfileTable | 1.3.6.1.4.1.4874.2.2.57.1.15.2 | not-accessible | This table contains entries for elements of Statistics Profile definitions. | |
| T/F juniQosStatisticsProfileUpdateNow | 1.3.6.1.4.1.4874.2.2.57.1.15.2.1.10 | TruthValue | read-create | When set to true, modifications made to the statistics profile object will be committed to the line cards. |
| T/F juniQosStatisticsProfileUpdatePending | 1.3.6.1.4.1.4874.2.2.57.1.15.2.1.9 | TruthValue | read-only | True if modifications have been made to the statistics profile object which have not been committed to the line cards. |
| juniQosSVlanIdSupport | 1.3.6.1.4.1.4874.2.2.57.1.19 | |||
| juniQosSVlanIdSupportGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.26 | This group defines QoS stacked vlan port/id listing support. | ||
| juniQosSVlanIdTable | 1.3.6.1.4.1.4874.2.2.57.1.19.1 | not-accessible | This table contains an entry for each possible Ethernet port/stacked vlan id. | |
| juniQosSVlanIdTableEntry | 1.3.6.1.4.1.4874.2.2.57.1.19.1.1 | not-accessible | Each entry is a stacked vlan Ethernet port/stacked vlan ID. | |
| U32 juniQosSVlanIdTablePortUid | 1.3.6.1.4.1.4874.2.2.57.1.19.1.1.2 | Unsigned32 | read-only | The UID of the Ethernet port on which the stacked vlan is defined |
| U32 juniQosSVlanIdTableSVlanId | 1.3.6.1.4.1.4874.2.2.57.1.19.1.1.3 | Unsigned32 | read-only | The stacked vlan ID |
| U32 juniQosSVlanIdTableSVlanUid | 1.3.6.1.4.1.4874.2.2.57.1.19.1.1.1 | Unsigned32 | not-accessible | The stacked vlan UID |
| juniQosSVlanUidSupport | 1.3.6.1.4.1.4874.2.2.57.1.18 | |||
| juniQosSVlanUidSupportGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.25 | This group defines QoS stacked vlan UID listing support. | ||
| juniQosSVlanUidTable | 1.3.6.1.4.1.4874.2.2.57.1.18.1 | not-accessible | This table contains an entry for each possible stacked vlan UID. | |
| juniQosSVlanUidTableEntry | 1.3.6.1.4.1.4874.2.2.57.1.18.1.1 | not-accessible | Each entry is a stacked vlan UID. | |
| U32 juniQosSVlanUidTablePortUid | 1.3.6.1.4.1.4874.2.2.57.1.18.1.1.1 | Unsigned32 | not-accessible | The UID of the Ethernet port on which the stacked vlan is defined |
| U32 juniQosSVlanUidTableSVlanId | 1.3.6.1.4.1.4874.2.2.57.1.18.1.1.2 | Unsigned32 | not-accessible | The stacked vlan ID |
| U32 juniQosSVlanUidTableSVlanUid | 1.3.6.1.4.1.4874.2.2.57.1.18.1.1.3 | Unsigned32 | read-only | The stacked vlan UID |
| G32 juniQosTrafficClassCount | 1.3.6.1.4.1.4874.2.2.57.1.2.1 | Gauge32 | read-only | This object reflects the number of configured traffic classes. |
| juniQosTrafficClassEntry | 1.3.6.1.4.1.4874.2.2.57.1.3.2.1 | not-accessible | Each entry describes the characteristics of a traffic class element. | |
| juniQosTrafficClassGroupEntry | 1.3.6.1.4.1.4874.2.2.57.1.4.2.1 | not-accessible | Each entry describes the characteristics of a traffic class group element. | |
| juniQosTrafficClassGroupEntryEntry | 1.3.6.1.4.1.4874.2.2.57.1.5.1.1 | not-accessible | Each entry ties a traffic class table entry to a traffic class group. | |
| juniQosTrafficClassGroupEntryList | 1.3.6.1.4.1.4874.2.2.57.1.5 | |||
| ROW juniQosTrafficClassGroupEntryRowStatus | 1.3.6.1.4.1.4874.2.2.57.1.5.1.1.1 | RowStatus | read-create | Controls creation/deletion of conceptual rows within this table. All rowStatus modes are supported. To create an entry in this table, the following entry object MUST be explicitly configured: juniQosTrafficClassGroupEntryRowStatus |
| juniQosTrafficClassGroupEntryTable | 1.3.6.1.4.1.4874.2.2.57.1.5.1 | not-accessible | This table identifies which traffic classes are in each traffic class group. | |
| T/F juniQosTrafficClassGroupExtendedGroup | 1.3.6.1.4.1.4874.2.2.57.1.4.2.1.8 | TruthValue | read-create | When true, the traffic class group is an extended group. False indicates the traffic class group is an auto-strict-priority group. |
| U32 juniQosTrafficClassGroupIndex | 1.3.6.1.4.1.4874.2.2.57.1.4.2.1.1 | Unsigned32 | not-accessible | The number of the traffic class entry which is defined by this row. |
| T/F juniQosTrafficClassGroupIsReferencedByQosProfile | 1.3.6.1.4.1.4874.2.2.57.1.4.2.1.6 | TruthValue | read-only | When true, the traffic class group is referenced by a QoS profile. |
| juniQosTrafficClassGroupList | 1.3.6.1.4.1.4874.2.2.57.1.4 | |||
| juniQosTrafficClassGroupListGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.4 | This obsolete group defines QoS traffic class group management. This group became obsolete when multiple traffic class group support was added. | ||
| juniQosTrafficClassGroupListGroup2 | 1.3.6.1.4.1.4874.2.2.57.2.2.22 | This group defines QoS traffic class group management. | ||
| STR juniQosTrafficClassGroupName | 1.3.6.1.4.1.4874.2.2.57.1.4.2.1.3 | DisplayString | read-create | Specifies the name of the traffic class group defined by this row. |
| U32 juniQosTrafficClassGroupNextIndex | 1.3.6.1.4.1.4874.2.2.57.1.4.1 | Unsigned32 | read-only | This scalar object returns the index of the next available row in the juniQosTrafficClassGroupTable. |
| ROW juniQosTrafficClassGroupRowStatus | 1.3.6.1.4.1.4874.2.2.57.1.4.2.1.2 | RowStatus | read-create | Controls creation/deletion of conceptual rows within this table. All rowStatus modes are supported. To create an entry in this table, the following entry objects MUST be explicitly configured: juniQosTrafficClassGroupRowStatus juniQosTrafficClassGroupName |
| I32 juniQosTrafficClassGroupSlotNumber | 1.3.6.1.4.1.4874.2.2.57.1.4.2.1.7 | Integer32 | read-create | The number of the slot on which this traffic class group is applied. Traffic class groups may be global or local. Global groups indicate that the traffic class group is to be applied to each line card in the chassis. The value of this object is -1 for global traffic class groups. Local traffic class groups override global traffic class groups and are applied to the slot indicated by the value of this object. |
| juniQosTrafficClassGroupTable | 1.3.6.1.4.1.4874.2.2.57.1.4.2 | not-accessible | This table contains entries for elements of Traffic Class group definitions. | |
| T/F juniQosTrafficClassGroupUpdateNow | 1.3.6.1.4.1.4874.2.2.57.1.4.2.1.5 | TruthValue | read-create | When set to true, modifications made to the traffic class group object will be committed to the line cards. |
| T/F juniQosTrafficClassGroupUpdatePending | 1.3.6.1.4.1.4874.2.2.57.1.4.2.1.4 | TruthValue | read-only | True if modifications have been made to the traffic class group object which have not been committed to the line cards. |
| U32 juniQosTrafficClassIndex | 1.3.6.1.4.1.4874.2.2.57.1.3.2.1.1 | Unsigned32 | not-accessible | The number of the traffic class entry which is defined by this row. |
| T/F juniQosTrafficClassIsReferencedByGroup | 1.3.6.1.4.1.4874.2.2.57.1.3.2.1.8 | TruthValue | read-only | When true, the traffic class is referenced by a traffic class group. |
| T/F juniQosTrafficClassIsReferencedByQosProfile | 1.3.6.1.4.1.4874.2.2.57.1.3.2.1.9 | TruthValue | read-only | When true, the traffic class is referenced by a QoS profile. |
| juniQosTrafficClassList | 1.3.6.1.4.1.4874.2.2.57.1.3 | |||
| juniQosTrafficClassListGroup | 1.3.6.1.4.1.4874.2.2.57.2.2.3 | This group defines QoS traffic class management. | ||
| STR juniQosTrafficClassName | 1.3.6.1.4.1.4874.2.2.57.1.3.2.1.3 | DisplayString | read-create | Specifies the name of the traffic class defined by this row. |
| U32 juniQosTrafficClassNextIndex | 1.3.6.1.4.1.4874.2.2.57.1.3.1 | Unsigned32 | read-only | This scalar object returns the index of the next available row in the juniQosTrafficClassTable. |
| ROW juniQosTrafficClassRowStatus | 1.3.6.1.4.1.4874.2.2.57.1.3.2.1.2 | RowStatus | read-create | Controls creation/deletion of conceptual rows within this table. All rowStatus modes are supported. To create an entry in this table, the following entry objects MUST be explicitly configured: juniQosTrafficClassRowStatus juniQosTrafficClassName |
| T/F juniQosTrafficClassStrictPriority | 1.3.6.1.4.1.4874.2.2.57.1.3.2.1.5 | TruthValue | read-create | The traffic to be dequeued before all other classes. |
| juniQosTrafficClassTable | 1.3.6.1.4.1.4874.2.2.57.1.3.2 | not-accessible | This table contains entries for elements of Traffic Class definitions. | |
| T/F juniQosTrafficClassUpdateNow | 1.3.6.1.4.1.4874.2.2.57.1.3.2.1.7 | TruthValue | read-create | When set to true, modifications made to the traffic class object will be committed to the line cards. |
| T/F juniQosTrafficClassUpdatePending | 1.3.6.1.4.1.4874.2.2.57.1.3.2.1.6 | TruthValue | read-only | True if modifications have been made to the traffic class object which have not been committed to the line cards. |
| U32 juniQosTrafficClassWeight | 1.3.6.1.4.1.4874.2.2.57.1.3.2.1.4 | Unsigned32 | read-create | The relative weight for queues in this traffic class. |
RFC description
Manages Quality of Service (QoS) policies, traffic shaping, and scheduler profiles on Juniper routers.
Start monitoring Juniper Networks E-series broadband router (QoS queues/schedulers/traffic shaping) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.