| OID symbolic | OID numeric | Type | Access | Description |
|---|
| jnxPWAtmMIB | 1.3.6.1.4.1.2636.3.57 | | | This MIB module defines objects used for managing
the atm pseudowires in Juniper products. |
| jnxpwAtmNotifications | 1.3.6.1.4.1.2636.3.57.0 | | | |
| jnxpwAtmObjects | 1.3.6.1.4.1.2636.3.57.1 | | | |
| jnxpwAtmCfgTable | 1.3.6.1.4.1.2636.3.57.1.1 | | not-accessible | This table specifies generic information for an ATM PW
to be carried over PSN in any mode. |
| jnxpwAtmCfgEntry | 1.3.6.1.4.1.2636.3.57.1.1.1 | | not-accessible | This table contains a set of parameters for
the ATM PW that needs to be adapted and carried
over PSN. This table is indexed by pwIndex from
pwTable. An entry is created for every newly ATM
type associated pwIndex in the pwTable. Unless
otherwise specified, all read-write objects in
this table MAY be changed when the PW is defined
as not active and all RW objects values must
persist after reboot |
| U32 jnxpwAtmCfgMaxCellConcatenation | 1.3.6.1.4.1.2636.3.57.1.1.1.1 | Unsigned32 | read-only | The maximum number of ATM cells that can be
concatenated into one PW packet towards PSN.
In non LDP or other signaling protocol environment,
this object MAY be changed at anytime, but traffic
might be interuppted, otherwise, it may be changed
when PW is not active. |
| U32 jnxpwAtmCfgFarEndMaxCellConcatenation | 1.3.6.1.4.1.2636.3.57.1.1.1.2 | Unsigned32 | read-only | The maximum number of ATM cells that can be
concatenated into one PW packet towards PSN as reported by
the far end. If no LDP in use, the object will either
return value 0 or allow setting it for calculating
protocol overhead. |
| INT jnxpwAtmCfgTimeoutMode | 1.3.6.1.4.1.2636.3.57.1.1.1.3 | INTEGER | read-only | This objects determines whether a packet can be
transmitted to the PSN based on time out expiration
for collecting cells or not. The actual handling of the
time out is implementation specific-as such this object
may be changed at any time under proper consideration of
traffic interupption effect. |
| T/F jnxpwAtmClpQosMapping | 1.3.6.1.4.1.2636.3.57.1.1.1.4 | TruthValue | read-only | This Object indicates whether the CLP bits should be
considered when setting the value in the Quality
of Service fields of the encapsulating protocol
(e.g. EXP fields of the MPLS Label Stack). Selecting
True allows the drop precedence to be preserved
across the PSN. In transparent cell transport,
the value of this object MUST be false(2), in other
cases it can be changed at any time. |
| jnxpwAtmOutboundNto1Table | 1.3.6.1.4.1.2636.3.57.1.2 | | not-accessible | This table specifies the information for an ATM PW to
be carried over PSN in the outbound direction. Up to
N entries can be created in this table for every
entry in the pwTable with a pwType equal to:
atmCellNto1Vcc(9), or atmCellNto1Vpc(10).
An entry can be created only when the VP/VC are known.
A single entry will be created in this table for every
entry in the pwTable with a pwType equal to
one of the following: atmCell1to1Vcc(12), or
atmCell1to1Vpc(13), or atmAal5PduVcc(14), or
atmAal5SduVcc(2), or atmTransparent(3). |
| jnxpwAtmOutboundNto1Entry | 1.3.6.1.4.1.2636.3.57.1.2.1 | | not-accessible | A row in this table represents an ATM PW that needs to be
adapted and carried over PSN. This table is indexed by
pwIndex from pwTable and the ATM interface with VPL/ VCLs.
In atmTransparent(3), Vpi and VCi will be 0xFFFF
during set operation.
Unless otherwise specified, all read-create objects in this
table MUST NOT be changed after row activation
and SHOULD remain unchanged after reboot. |
| NUM jnxpwAtmOutboundNto1AtmIf | 1.3.6.1.4.1.2636.3.57.1.2.1.1 | InterfaceIndex | not-accessible | The ATM Interface that receives cells from the ATM network. |
| OID jnxpwAtmOutboundNto1Vpi | 1.3.6.1.4.1.2636.3.57.1.2.1.2 | AtmVpIdentifier | not-accessible | VPI value of this ATM PW. In atmTransparent(3),
Vpi will be the equivalent of 0xFFFF |
| OID jnxpwAtmOutboundNto1Vci | 1.3.6.1.4.1.2636.3.57.1.2.1.3 | AtmVcIdentifier | not-accessible | VCI value of this ATM PW. In atmTransparent(3), or
VP case, the value will be the equivalent of
0xFFFF |
| ROW jnxpwAtmOutboundNto1RowStatus | 1.3.6.1.4.1.2636.3.57.1.2.1.4 | RowStatus | read-only | This Object is used to create, modify or delete a row in
this table. |
| NUM jnxpwAtmOutboundNto1TrafficParamDescr | 1.3.6.1.4.1.2636.3.57.1.2.1.5 | RowPointer | read-only | This object represents a pointer to a ATM traffic parameter
specific row in either private or standard table which will
be employed while receiving cells from the ATM network.
This table should contain a set
of self-consistent ATM traffic parameters including the ATM
traffic service category. A value of 0.0 indicates Best
Effort. |
| OID jnxpwAtmOutboundNto1MappedVpi | 1.3.6.1.4.1.2636.3.57.1.2.1.6 | AtmVpIdentifier | read-only | The egress generated VPI value of this ATM PW. The
entry is valid for PW type of atmCellNto1Vcc(9),
atmCellNto1Vpc(10), atmCell1to1Vcc(12), or
atmCell1to1Vpc(13). In other types, the value will be the
equivalent of 0xFFFF. Value MAY be changed when the
PW is defined as not active |
| OID jnxpwAtmOutboundNto1MappedVci | 1.3.6.1.4.1.2636.3.57.1.2.1.7 | AtmVcIdentifier | read-only | The egress generated VCI value of this ATM PW. The
entry is valid for PW type of atmCellNto1Vcc(9),
atmCellNto1Vpc(10), atmCell1to1Vcc(12), or
atmCell1to1Vpc(13. In VP case or other types, the
value will be the equivalent of 0xFFFF.
Value MAY be changed when the PW is defined
as not active. |
| jnxpwAtmInboundNto1Table | 1.3.6.1.4.1.2636.3.57.1.3 | | not-accessible | This table specifies the information for an ATM PW to
be carried over PSN in the Inbound direction. Up to
N entries can be created in this table for every
entry in the pwTable with a pwType equal to:
atmCellNto1Vcc(9), or atmCellNto1Vpc(10).
An entry can be created only when the VP/VC are known.
A single entry will be created in this table for every
entry in the pwTable with a pwType equal to
one of the following:atmCell1to1Vcc(12), or
atmCell1to1Vpc(13), or atmAal5PduVcc(14), or
atmAal5SduVcc(2), or atmTransparent(3). |
| jnxpwAtmInboundNto1Entry | 1.3.6.1.4.1.2636.3.57.1.3.1 | | not-accessible | A row in this table represents an ATM PW that needs to be
adapted and carried over PSN. This table is indexed by
pwIndex from pwTable and the ATM interface with VPL/ VCLs.
In atmTransparent(3), Vpi and VCi will be 0xFFFF
during set operation.
Unless otherwise specified, all Read-Creat objects in this
table MUST NOT be changed after row activation
and SHOULD remain unchanged after reboot. |
| NUM jnxpwAtmInboundNto1AtmIf | 1.3.6.1.4.1.2636.3.57.1.3.1.1 | InterfaceIndex | not-accessible | The ATM Interface that receives cells from the ATM network. |
| OID jnxpwAtmInboundNto1Vpi | 1.3.6.1.4.1.2636.3.57.1.3.1.2 | AtmVpIdentifier | not-accessible | VPI value of this ATM PW. In atmTransparent(3),
Vpi will be the equivalent of 0xFFFF. |
| OID jnxpwAtmInboundNto1Vci | 1.3.6.1.4.1.2636.3.57.1.3.1.3 | AtmVcIdentifier | not-accessible | VCI value of this ATM PW. In atmTransparent(3), or
VP case, the value will be the equivalent of
0xFFFF |
| ROW jnxpwAtmInboundNto1RowStatus | 1.3.6.1.4.1.2636.3.57.1.3.1.4 | RowStatus | read-only | This Object is used to create, modify or delete a row in
this table. |
| NUM jnxpwAtmInboundNto1TrafficParamDescr | 1.3.6.1.4.1.2636.3.57.1.3.1.5 | RowPointer | read-only | This object represents a pointer to a ATM traffic parameter
specific row in either private or standard table which will
be employed while receiving cells from the ATM network.
This table should contain a set
of self-consistent ATM traffic parameters including the ATM
traffic service category. A value of 0.0 indicates Best
Effort. |
| OID jnxpwAtmInboundNto1MappedVpi | 1.3.6.1.4.1.2636.3.57.1.3.1.6 | AtmVpIdentifier | read-only | The generated VPI value of this ATM PW. The
entry is valid for PW type of atmCellNto1Vcc(9),
atmCellNto1Vpc(10), atmCell1to1Vcc(12), or
atmCell1to1Vpc(13). In other types, the value will be the
equivalent of 0xFFFF. Value MAY be changed when the
PW is defined as not active. |
| OID jnxpwAtmInboundNto1MappedVci | 1.3.6.1.4.1.2636.3.57.1.3.1.7 | AtmVcIdentifier | read-only | The generated VCI value of this ATM PW. The
entry is valid for PW type of atmCellNto1Vcc(9),
atmCellNto1Vpc(10), atmCell1to1Vcc(12), or
atmCell1to1Vpc(13. In VP case or other types, the
value will be the equivalent of 0xFFFF.
Value MAY be changed when the
PW is defined as not active. |
| jnxpwAtmPerfCurrentTable | 1.3.6.1.4.1.2636.3.57.1.4 | | not-accessible | The current 15 minute interval counts are in
this table.
This table provides performance information per ATM PW. |
| jnxpwAtmPerfCurrentEntry | 1.3.6.1.4.1.2636.3.57.1.4.1 | | not-accessible | An entry in this table is created by the agent for every
pwAtmCfgTable entry. After 15 minutes, the contents of this
table entry are copied to a new entry in the
pwAtmPerfInterval table and the counts in this entry
are reset to zero. |
| PER jnxpwAtmPerfCurrentMissingPkts | 1.3.6.1.4.1.2636.3.57.1.4.1.1 | PerfCurrentCount | read-only | Number of missing packets (as detected via control word
sequence number gaps). |
| PER jnxpwAtmPerfCurrentPktsReOrder | 1.3.6.1.4.1.2636.3.57.1.4.1.2 | PerfCurrentCount | read-only | Number of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this Feature. |
| PER jnxpwAtmPerfCurrentPktsMisOrder | 1.3.6.1.4.1.2636.3.57.1.4.1.3 | PerfCurrentCount | read-only | Number of packets detected out of order (via control word
sequence numbers). |
| PER jnxpwAtmPerfCurrentPktsTimeout | 1.3.6.1.4.1.2636.3.57.1.4.1.4 | PerfCurrentCount | read-only | Number of packets transmitted due to timeout expiration
while attempting to collect cells. |
| C64 jnxpwAtmPerfCurrentPktsXmit | 1.3.6.1.4.1.2636.3.57.1.4.1.5 | Counter64 | read-only | Number of transmitted packets. |
| PER jnxpwAtmPerfCurrentCellsDropped | 1.3.6.1.4.1.2636.3.57.1.4.1.6 | PerfCurrentCount | read-only | Number of dropped cells. |
| C64 jnxpwAtmPerfCurrentPktsReceived | 1.3.6.1.4.1.2636.3.57.1.4.1.7 | Counter64 | read-only | Number of received packets. |
| C64 jnxpwAtmPerfCurrentUnknownCells | 1.3.6.1.4.1.2636.3.57.1.4.1.8 | Counter64 | read-only | Number of cells received from the PSN with unknown VPI or
VCI values. This object is relevant only in N:1 mode. |
| jnxpwAtmPerfIntervalTable | 1.3.6.1.4.1.2636.3.57.1.5 | | not-accessible | This table provides performance information per ATM PW
similar to the pwAtmPerfCurrentTable above. However,
these counts represent historical 15 minute intervals.
Typically, this table will have a maximum of 96 entries
for a 24 hour period. |
| jnxpwAtmPerfIntervalEntry | 1.3.6.1.4.1.2636.3.57.1.5.1 | | not-accessible | An entry in this table is created by the agent for
every pwAtmPerfCurrentEntry that is 15 minutes old.
The contents of the Current entry are copied to the new
entry here. The Current entry, then resets its counts
to zero for the next current 15 minute interval. |
| U32 jnxpwAtmPerfIntervalNumber | 1.3.6.1.4.1.2636.3.57.1.5.1.1 | Unsigned32 | not-accessible | A number (normally between 1 and 96 to cover a 24 hour
period) which identifies the interval for which the set
of statistics is available. The interval identified by 1
is the most recently completed 15 minute interval, and
the interval identified by N is the interval immediately
preceding the one identified by N-1. The minimum range of
N is 1 through 4. The default range is 1 through 32. The
maximum value of N is 96. |
| T/F jnxpwAtmPerfIntervalValidData | 1.3.6.1.4.1.2636.3.57.1.5.1.2 | TruthValue | read-only | This variable indicates if the data for this interval
is valid. |
| U32 jnxpwAtmPerfIntervalDuration | 1.3.6.1.4.1.2636.3.57.1.5.1.3 | Unsigned32 | read-only | The duration of a particular interval in seconds,
Adjustments in the system's time-of-day clock, may
cause the interval to be greater or less than, the
normal value. Therefore this actual interval value
is provided. |
| NUM jnxpwAtmPerfIntervalMissingPkts | 1.3.6.1.4.1.2636.3.57.1.5.1.4 | PerfIntervalCount | read-only | Number of missing packets (as detected via control
word sequence number gaps). |
| NUM jnxpwAtmPerfIntervalPktsReOrder | 1.3.6.1.4.1.2636.3.57.1.5.1.5 | PerfIntervalCount | read-only | Number of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this
Feature. |
| NUM jnxpwAtmPerfIntervalPktsMisOrder | 1.3.6.1.4.1.2636.3.57.1.5.1.6 | PerfIntervalCount | read-only | Number of packets detected out of order (via control word
sequence numbers). |
| NUM jnxpwAtmPerfIntervalPktsTimeout | 1.3.6.1.4.1.2636.3.57.1.5.1.7 | PerfIntervalCount | read-only | Number of packets transmitted due to timeout expiration. |
| C64 jnxpwAtmPerfIntervalPktsXmit | 1.3.6.1.4.1.2636.3.57.1.5.1.8 | Counter64 | read-only | Number of transmitted packets. |
| NUM jnxpwAtmPerfIntervalCellsDropped | 1.3.6.1.4.1.2636.3.57.1.5.1.9 | PerfIntervalCount | read-only | Number of dropped cells. |
| C64 jnxpwAtmPerfIntervalPktsReceived | 1.3.6.1.4.1.2636.3.57.1.5.1.10 | Counter64 | read-only | Number of received packets. |
| C64 jnxpwAtmPerfIntervalUnknownCells | 1.3.6.1.4.1.2636.3.57.1.5.1.11 | Counter64 | read-only | Number of cells received from the PSN with unknown VPI or
VCI values. This object is relevant only in N:1 mode. |
| jnxpwAtmPerf1DayIntervalTable | 1.3.6.1.4.1.2636.3.57.1.6 | | not-accessible | This table provides performance information per ATM PW
similar to the pwAtmPerfIntervalTable above. However,
these counters represent historical 1 day intervals up to
one full month. |
| jnxpwAtmPerf1DayIntervalEntry | 1.3.6.1.4.1.2636.3.57.1.6.1 | | not-accessible | An entry is created in this table by the agent
for every entry in the pwAtmCfgTable table. |
| U32 jnxpwAtmPerf1DayIntervalNumber | 1.3.6.1.4.1.2636.3.57.1.6.1.1 | Unsigned32 | not-accessible | The number of interval, where 1 indicates current day
measured period and 2 and above indicate previous days
respectively |
| T/F jnxpwAtmPerf1DayIntervalValidData | 1.3.6.1.4.1.2636.3.57.1.6.1.2 | TruthValue | read-only | This object indicates if the data for this interval
is valid. |
| U32 jnxpwAtmPerf1DayIntervalDuration | 1.3.6.1.4.1.2636.3.57.1.6.1.3 | Unsigned32 | read-only | The duration of a particular interval in seconds,
Adjustments in the system's time-of-day clock, may
cause the interval to be greater or less than, the
normal value. Therefore this actual interval value
is provided. |
| C32 jnxpwAtmPerf1DayIntervalMissingPkts | 1.3.6.1.4.1.2636.3.57.1.6.1.4 | Counter32 | read-only | Number of missing packets (as detected via control word
sequence number gaps). |
| C32 jnxpwAtmPerf1DayIntervalPktsReOrder | 1.3.6.1.4.1.2636.3.57.1.6.1.5 | Counter32 | read-only | Number of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this
feature. |
| C32 jnxpwAtmPerf1DayIntervalPktsMisOrder | 1.3.6.1.4.1.2636.3.57.1.6.1.6 | Counter32 | read-only | Number of packets detected out of order(via control word
sequence numbers), and could not be re-ordered. |
| C32 jnxpwAtmPerf1DayIntervalPktsTimeout | 1.3.6.1.4.1.2636.3.57.1.6.1.7 | Counter32 | read-only | Number of packets transmitted due to timeout expiration. |
| C64 jnxpwAtmPerf1DayIntervalPktsXmit | 1.3.6.1.4.1.2636.3.57.1.6.1.8 | Counter64 | read-only | Number of transmitted packets. |
| C32 jnxpwAtmPerf1DayIntervalCellsDropped | 1.3.6.1.4.1.2636.3.57.1.6.1.9 | Counter32 | read-only | Number of dropped cells. |
| C64 jnxpwAtmPerf1DayIntervalPktsReceived | 1.3.6.1.4.1.2636.3.57.1.6.1.10 | Counter64 | read-only | Number of received packets. |
| C64 jnxpwAtmPerf1DayIntervalUnknownCells | 1.3.6.1.4.1.2636.3.57.1.6.1.11 | Counter64 | read-only | Number of cells received from the PSN with unknown VPI
or VCI value. This object is relevant only in N:1 mode. |
| jnxpwAtmConformance | 1.3.6.1.4.1.2636.3.57.2 | | | |
