All MIBs › InterSeptor-MIB
Category: Domain: Security, VPN and Security
Description: InterSeptor network security appliance MIB providing SNMP objects for intrusion detection and traffic monitoring on perimeter devices.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is InterSeptor-MIB?
InterSeptor-MIB is the enterprise MIB for the InterSeptor line of network security/firewall appliances (marketed under the Jacarta/webAppliance product branding), providing objects for device identification, configuration, and traffic monitoring on perimeter security devices. It exposes identity data (manufacturer, model, agent software version, device name), network/IP configuration (address, gateway, subnet mask), and time synchronization settings including NTP server and sync status. Its monitoring emphasis includes confirming the software version in use (inSeptIdentAgentSoftwareVersion) for patch/vulnerability tracking and verifying the device's clock is properly synced via NTP, both important for security-appliance integrity and accurate log correlation. It is a largely self-contained vendor MIB, though its date/time and IP configuration objects parallel concepts in standard system/IP MIBs. It is deployed on InterSeptor perimeter security/intrusion-detection appliances protecting enterprise network boundaries. Engineers can download the InterSeptor-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in InterSeptor-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- InterSeptor/Jacarta network security appliance
Monitoring Examples
An administrator checks inSeptIdentAgentSoftwareVersion against inSeptConfigMibVersion to confirm the appliance is running an expected, patched firmware level. inSeptConfigTimeFromNtp and inSeptConfigNtpIpAddress are polled to verify the device's clock discipline is functioning, since a security appliance with drifted time can produce log timestamps that don't correlate with other systems during an incident investigation. inSeptConfigIpAddress, inSeptConfigGateway, and inSeptConfigSubnetMask are checked to confirm the management interface configuration hasn't drifted from the documented baseline.
What Can Be Monitored
- device identity and software version
- management IP/gateway/subnet configuration
- system date and time
- NTP synchronization status
- NTP server address
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| enterprises |
From RFC1213-MIB
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| jacarta | 1.3.6.1.4.1.19011 | |||
| product | 1.3.6.1.4.1.19011.1 | |||
| webAppliance | 1.3.6.1.4.1.19011.1.3 | |||
| inSept | 1.3.6.1.4.1.19011.1.3.1 | |||
| inSeptObjects | 1.3.6.1.4.1.19011.1.3.1.1 | |||
| inSeptIdent | 1.3.6.1.4.1.19011.1.3.1.1.1 | |||
| STR inSeptIdentManufacturer | 1.3.6.1.4.1.19011.1.3.1.1.1.1 | DisplayString | read-only | The name of the interSeptor manufacturer. |
| STR inSeptIdentModel | 1.3.6.1.4.1.19011.1.3.1.1.1.2 | DisplayString | read-only | The interSeptor Model designation. |
| STR inSeptIdentAgentSoftwareVersion | 1.3.6.1.4.1.19011.1.3.1.1.1.3 | DisplayString | read-only | The interSeptor software/firmware version. |
| STR inSeptIdentName | 1.3.6.1.4.1.19011.1.3.1.1.1.4 | DisplayString | read-write | A string identifying the interSeptor. This object should be set by the administrator. |
| inSeptConfig | 1.3.6.1.4.1.19011.1.3.1.1.2 | |||
| INT inSeptConfigMibVersion | 1.3.6.1.4.1.19011.1.3.1.1.2.1 | INTEGER | read-only | The version of MIB spec. |
| inSeptConfigNetwork | 1.3.6.1.4.1.19011.1.3.1.1.2.2 | |||
| IP inSeptConfigIpAddress | 1.3.6.1.4.1.19011.1.3.1.1.2.2.1 | IpAddress | read-write | The ip address that NMS can identify the managed device |
| IP inSeptConfigGateway | 1.3.6.1.4.1.19011.1.3.1.1.2.2.2 | IpAddress | read-write | The default gateway that allows the device to be managed through routers |
| IP inSeptConfigSubnetMask | 1.3.6.1.4.1.19011.1.3.1.1.2.2.3 | IpAddress | read-write | Internet address subnet mask |
| inSeptConfigDateTime | 1.3.6.1.4.1.19011.1.3.1.1.2.3 | |||
| STR inSeptConfigDate | 1.3.6.1.4.1.19011.1.3.1.1.2.3.1 | DisplayString | read-write | The date in inSept, format is (dd/mm/yyyy) |
| STR inSeptConfigTime | 1.3.6.1.4.1.19011.1.3.1.1.2.3.2 | DisplayString | read-write | The time in interSeptor, format is (hh:mm:ss) |
| INT inSeptConfigTimeFromNtp | 1.3.6.1.4.1.19011.1.3.1.1.2.3.3 | INTEGER | read-write | Enable/disable update date/time from NTP server. |
| IP inSeptConfigNtpIpAddress | 1.3.6.1.4.1.19011.1.3.1.1.2.3.4 | IpAddress | read-write | NTP IP address. |
| INT inSeptConfigNtpTimeZone | 1.3.6.1.4.1.19011.1.3.1.1.2.3.5 | INTEGER | read-write | Enable/disable update date/time from NTP server. |
| INT inSeptConfigDayLightSaving | 1.3.6.1.4.1.19011.1.3.1.1.2.3.6 | INTEGER | read-write | Enable/disable daylight saving for NTP time, if enabled, the time get from NTP will be set set one hour in advance to reflect daylight saving status. |
| inSeptConfigLog | 1.3.6.1.4.1.19011.1.3.1.1.2.4 | |||
| INT inSeptConfigHistoryLogFrequency | 1.3.6.1.4.1.19011.1.3.1.1.2.4.1 | INTEGER | read-write | The frequency of the update of the history log. The value is in seconds |
| INT inSeptConfigExtHistoryLogFrequency | 1.3.6.1.4.1.19011.1.3.1.1.2.4.2 | INTEGER | read-write | The frequency of the update of the extended history log. The value is in seconds |
| INT inSeptConfigConfigurationLog | 1.3.6.1.4.1.19011.1.3.1.1.2.4.3 | INTEGER | read-write | Enable/disable inSept to log parameter change. |
| INT inSeptConfigDhcpStatue | 1.3.6.1.4.1.19011.1.3.1.1.2.5 | INTEGER | read-write | Enable or disable DHCP/BootP capability |
| INT inSeptConfigPingStatue | 1.3.6.1.4.1.19011.1.3.1.1.2.6 | INTEGER | read-write | Enable or disable Ping Echo capability |
| INT inSeptConfigTftpStatue | 1.3.6.1.4.1.19011.1.3.1.1.2.7 | INTEGER | read-write | Enable or disable TFTP network upgrade capability |
| inSeptConfigTelnet | 1.3.6.1.4.1.19011.1.3.1.1.2.8 | |||
| INT inSeptConfigTelnetStatue | 1.3.6.1.4.1.19011.1.3.1.1.2.8.1 | INTEGER | read-write | Enable or disable telnet access |
| INT inSeptConfigTelnetPortNumber | 1.3.6.1.4.1.19011.1.3.1.1.2.8.2 | INTEGER | read-write | Setting the server port of telnet. |
| inSeptConfigHttp | 1.3.6.1.4.1.19011.1.3.1.1.2.9 | |||
| INT inSeptConfigHttpStatue | 1.3.6.1.4.1.19011.1.3.1.1.2.9.1 | INTEGER | read-write | Enable or disable HTTP access |
| INT inSeptConfigHttpPortNumber | 1.3.6.1.4.1.19011.1.3.1.1.2.9.2 | INTEGER | read-write | Setting the server port of HTTP. |
| INT inSeptConfigHttpSecurity | 1.3.6.1.4.1.19011.1.3.1.1.2.9.3 | INTEGER | read-write | Enable/disable HTTP access for read-only users |
| inSeptConfigSnmp | 1.3.6.1.4.1.19011.1.3.1.1.2.10 | |||
| INT inSeptConfigSnmpStatue | 1.3.6.1.4.1.19011.1.3.1.1.2.10.1 | INTEGER | read-write | Enable or disable SNMP access |
| INT inSeptConfigSnmpPortNumber | 1.3.6.1.4.1.19011.1.3.1.1.2.10.2 | INTEGER | read-write | Setting the server port of SNMP. |
| inSeptConfigControl | 1.3.6.1.4.1.19011.1.3.1.1.2.11 | |||
| INT inSeptConfigResetToDefault | 1.3.6.1.4.1.19011.1.3.1.1.2.11.1 | INTEGER | read-write | Reset all parameters of interSeptor to default value |
| INT inSeptConfigRestart | 1.3.6.1.4.1.19011.1.3.1.1.2.11.2 | INTEGER | read-write | Restart interSeptor |
| inSeptConfigTrap | 1.3.6.1.4.1.19011.1.3.1.1.2.12 | |||
| INT inSeptConfigTrapRetryCount | 1.3.6.1.4.1.19011.1.3.1.1.2.12.1 | INTEGER | read-write | The count of repeat traps to send to NMS before trap acknowledgement is received. |
| INT inSeptConfigTrapRetryTime | 1.3.6.1.4.1.19011.1.3.1.1.2.12.2 | INTEGER | read-write | The time between retrying to send traps to NMS. |
| INT inSeptConfigTrapAckSignature | 1.3.6.1.4.1.19011.1.3.1.1.2.12.3 | INTEGER | read-write | The signature of trap acknowledgement. |
| INT inSeptConfigPollRate | 1.3.6.1.4.1.19011.1.3.1.1.2.13 | INTEGER | read-write | The frequency that interSeptor updates readings from sensors (unit : second). |
| inSeptConfigTrapsReceiversTable | 1.3.6.1.4.1.19011.1.3.1.1.2.14 | not-accessible | A list of managers to send traps to. The number of entries is given by the value of inSeptConfigNumTrapReceivers | |
| inSeptConfigTrapsReceiversEntry | 1.3.6.1.4.1.19011.1.3.1.1.2.14.1 | not-accessible | The managers to send traps to. | |
| INT inSepttrapsIndex | 1.3.6.1.4.1.19011.1.3.1.1.2.14.1.1 | INTEGER | read-only | The index to a trap receiver entry. |
| IP inSepttrapsReceiverAddr | 1.3.6.1.4.1.19011.1.3.1.1.2.14.1.2 | IpAddress | read-write | The IP address of the manager to send a trap to. |
| STR inSeptreceiverCommunityString | 1.3.6.1.4.1.19011.1.3.1.1.2.14.1.3 | DisplayString | read-write | The community name to use in the trap when sent to the manager. |
| INT inSeptreceiverSeverityLevel | 1.3.6.1.4.1.19011.1.3.1.1.2.14.1.4 | INTEGER | read-write | The severity level of traps to be received by this manager. |
| STR inSeptreceiverDescription | 1.3.6.1.4.1.19011.1.3.1.1.2.14.1.5 | DisplayString | read-write | Description of trap receivers |
| inSeptConfigAccessControlTable | 1.3.6.1.4.1.19011.1.3.1.1.2.15 | not-accessible | A list of managers which can access interSeptor with private community string. | |
| inSeptConfigAccessControlEntry | 1.3.6.1.4.1.19011.1.3.1.1.2.15.1 | not-accessible | The managers. | |
| INT accessIndex | 1.3.6.1.4.1.19011.1.3.1.1.2.15.1.1 | INTEGER | read-only | The index to a access control entry. |
| IP accessControlAddr | 1.3.6.1.4.1.19011.1.3.1.1.2.15.1.2 | IpAddress | read-write | The IP address of the manager to access interSeptor |
| STR accessCommunityString | 1.3.6.1.4.1.19011.1.3.1.1.2.15.1.3 | DisplayString | read-write | The community name to use in the manager when access interSeptor |
| INT accessControlMode | 1.3.6.1.4.1.19011.1.3.1.1.2.15.1.4 | INTEGER | read-write | Access type, only read/Write access type can change parameter of interSeptor |
| INT inSeptConfigTemperatureUnit | 1.3.6.1.4.1.19011.1.3.1.1.2.16 | INTEGER | read-write | The temperature unit of the system, can be Celsius or Farenheit |
| INT inSeptConfigDateFormat | 1.3.6.1.4.1.19011.1.3.1.1.2.17 | INTEGER | read-write | The date format of the system, can be dd/mm/yyyy or mm/dd/yyyy |
| inSeptsensorMonitor | 1.3.6.1.4.1.19011.1.3.1.1.3 | |||
| INT inSeptsensorMonitorSensorNumber | 1.3.6.1.4.1.19011.1.3.1.1.3.1 | INTEGER | read-only | The number of sensors that can be monitored. |
| inSeptsensorMonitorSensorTable | 1.3.6.1.4.1.19011.1.3.1.1.3.2 | not-accessible | A list of sensor devices to be monitored. | |
| inSeptsensorMonitorSensorEntry | 1.3.6.1.4.1.19011.1.3.1.1.3.2.1 | not-accessible | The sensor device. | |
| INT inSeptsensorMonitorDeviceIndex | 1.3.6.1.4.1.19011.1.3.1.1.3.2.1.1 | INTEGER | read-only | The index to a sensor device entry. |
| INT inSeptsensorMonitorDeviceStatus | 1.3.6.1.4.1.19011.1.3.1.1.3.2.1.2 | INTEGER | read-only | The device type connected to interSeptor. |
| INT inSeptsensorMonitorDeviceTemperature | 1.3.6.1.4.1.19011.1.3.1.1.3.2.1.3 | INTEGER | read-only | The temperature of sensor on device interSeptor, the unit is 0.1 degree. |
| INT inSeptsensorMonitorDeviceTemperatureAlarm | 1.3.6.1.4.1.19011.1.3.1.1.3.2.1.4 | INTEGER | read-only | The alarm type of sensor on device interSeptor. |
| INT inSeptsensorMonitorDeviceHumidity | 1.3.6.1.4.1.19011.1.3.1.1.3.2.1.5 | INTEGER | read-only | The humidity of sensor on device interSeptor, the unit is 0.1%. |
| INT inSeptsensorMonitorDeviceHumidityAlarm | 1.3.6.1.4.1.19011.1.3.1.1.3.2.1.6 | INTEGER | read-only | The alarm type of sensor on device interSeptor. |
| INT inSeptsensorMonitorAlarm1 | 1.3.6.1.4.1.19011.1.3.1.1.3.2.1.7 | INTEGER | read-only | The device status of sensor 1 connected to interSeptor. |
| INT inSeptsensorMonitorAlarm2 | 1.3.6.1.4.1.19011.1.3.1.1.3.2.1.8 | INTEGER | read-only | The device status of sensor 2 connected to interSeptor. |
| inSeptsensorConfig | 1.3.6.1.4.1.19011.1.3.1.1.4 | |||
| INT inSeptsensorConfigSensorNumber | 1.3.6.1.4.1.19011.1.3.1.1.4.1 | INTEGER | read-only | The number of sensors that are connected to interSeptor. |
| inSeptsensorConfigSensorTable | 1.3.6.1.4.1.19011.1.3.1.1.4.2 | not-accessible | A list of sensor devices to be configured. | |
| inSeptsensorConfigSensorEntry | 1.3.6.1.4.1.19011.1.3.1.1.4.2.1 | not-accessible | The sensor device. | |
| INT inSeptsensorConfigDeviceIndex | 1.3.6.1.4.1.19011.1.3.1.1.4.2.1.1 | INTEGER | read-only | The index to a sensor device entry. |
| STR inSeptsensorConfigDeviceName | 1.3.6.1.4.1.19011.1.3.1.1.4.2.1.2 | DisplayString | read-write | The name of the sensor device for identification. |
| INT inSeptsensorConfigDeviceState | 1.3.6.1.4.1.19011.1.3.1.1.4.2.1.3 | INTEGER | read-write | The setup of sensor device type. |
| inSeptsensorConfigSensor1 | 1.3.6.1.4.1.19011.1.3.1.1.4.3 | |||
| STR inSeptsensorConfigSensor1DeviceName | 1.3.6.1.4.1.19011.1.3.1.1.4.3.1 | DisplayString | read-write | The name of sensor device. |
| INT inSeptsensorConfigSensor1DeviceState | 1.3.6.1.4.1.19011.1.3.1.1.4.3.2 | INTEGER | read-write | The setup of sensor device type. |
| inSeptsensorConfigSensor1Temperature | 1.3.6.1.4.1.19011.1.3.1.1.4.3.3 | |||
| STR inSeptsensorConfigSensor1TemperatureName | 1.3.6.1.4.1.19011.1.3.1.1.4.3.3.1 | DisplayString | read-write | The temperature sensor name. |
| INT inSeptsensorConfigSensor1TemperatureLowWarning | 1.3.6.1.4.1.19011.1.3.1.1.4.3.3.2 | INTEGER | read-write | The set point to trigger low warning alarm. |
| INT inSeptsensorConfigSensor1TemperatureLowCritical | 1.3.6.1.4.1.19011.1.3.1.1.4.3.3.3 | INTEGER | read-write | The threshold to trigger low critical alarm. |
| INT inSeptsensorConfigSensor1TemperatureHighWarning | 1.3.6.1.4.1.19011.1.3.1.1.4.3.3.4 | INTEGER | read-write | The threshold to trigger high warning alarm. |
| INT inSeptsensorConfigSensor1TemperatureHighCritical | 1.3.6.1.4.1.19011.1.3.1.1.4.3.3.5 | INTEGER | read-write | The threshold to trigger high critical alarm. |
| INT inSeptsensorConfigSensor1TemperatureHysteresis | 1.3.6.1.4.1.19011.1.3.1.1.4.3.3.6 | INTEGER | read-write | The set value to prevent too many alarms when temperature is hovering around the set threshold. |
| INT inSeptsensorConfigSensor1TemperatureCalibration | 1.3.6.1.4.1.19011.1.3.1.1.4.3.3.7 | INTEGER | read-write | The set value to get the correct temperature according to your reference temperature. |
| INT inSeptsensorConfigSensor1TemperatureLowWarningStatus | 1.3.6.1.4.1.19011.1.3.1.1.4.3.3.8 | INTEGER | read-write | Enable/disable the set point to trigger low warning alarm. |
| INT inSeptsensorConfigSensor1TemperatureLowCriticalStatus | 1.3.6.1.4.1.19011.1.3.1.1.4.3.3.9 | INTEGER | read-write | Enable/disable the set point to trigger low critical alarm. |
| INT inSeptsensorConfigSensor1TemperatureHighWarningStatus | 1.3.6.1.4.1.19011.1.3.1.1.4.3.3.10 | INTEGER | read-write | Enable/disable the set point to trigger high warning alarm. |
| INT inSeptsensorConfigSensor1TemperatureHighCriticalStatus | 1.3.6.1.4.1.19011.1.3.1.1.4.3.3.11 | INTEGER | read-write | Enable/disable the set point to trigger high critical alarm. |
| inSeptsensorConfigSensor1Humidity | 1.3.6.1.4.1.19011.1.3.1.1.4.3.4 | |||
| STR inSeptsensorConfigSensor1HumdityName | 1.3.6.1.4.1.19011.1.3.1.1.4.3.4.1 | DisplayString | read-write | The humidity sensor name. |
| INT inSeptsensorConfigSensor1HumidityLowWarning | 1.3.6.1.4.1.19011.1.3.1.1.4.3.4.2 | INTEGER | read-write | The set point to trigger low warning alarm. |
| INT inSeptsensorConfigSensor1HumidityLowCritical | 1.3.6.1.4.1.19011.1.3.1.1.4.3.4.3 | INTEGER | read-write | The threshole to trigger low critical alarm. |
| INT inSeptsensorConfigSensor1HumidityHighWarning | 1.3.6.1.4.1.19011.1.3.1.1.4.3.4.4 | INTEGER | read-write | The threshold to trigger high warning alarm. |
| INT inSeptsensorConfigSensor1HumidityHighCritical | 1.3.6.1.4.1.19011.1.3.1.1.4.3.4.5 | INTEGER | read-write | The threshold to trigger high critical alarm. |
| INT inSeptsensorConfigSensor1HumidityHysteresis | 1.3.6.1.4.1.19011.1.3.1.1.4.3.4.6 | INTEGER | read-write | The set value to prevent too many alarms when Humidity is hovering around the set threshold. |
| INT inSeptsensorConfigSensor1HumidityCalibration | 1.3.6.1.4.1.19011.1.3.1.1.4.3.4.7 | INTEGER | read-write | The set value to get the correct temperature according to your reference temperature. |
| INT inSeptsensorConfigSensor1HumidityLowWarningStatus | 1.3.6.1.4.1.19011.1.3.1.1.4.3.4.8 | INTEGER | read-write | Enable/disable the set point to trigger low warning alarm. |
| INT inSeptsensorConfigSensor1HumidityLowCriticalStatus | 1.3.6.1.4.1.19011.1.3.1.1.4.3.4.9 | INTEGER | read-write | Enable/disable the set point to trigger low critical alarm. |
| INT inSeptsensorConfigSensor1HumidityHighWarningStatus | 1.3.6.1.4.1.19011.1.3.1.1.4.3.4.10 | INTEGER | read-write | Enable/disable the set point to trigger high warning alarm. |
| INT inSeptsensorConfigSensor1HumidityHighCriticalStatus | 1.3.6.1.4.1.19011.1.3.1.1.4.3.4.11 | INTEGER | read-write | Enable/disable the set point to trigger high critical alarm. |
| inSeptsensorConfigSensor1Alarm1 | 1.3.6.1.4.1.19011.1.3.1.1.4.3.5 | |||
| STR inSeptsensorConfigSensor1Alarm1Name | 1.3.6.1.4.1.19011.1.3.1.1.4.3.5.1 | DisplayString | read-write | The name of alarm-1. |
| INT inSeptsensorConfigSensor1Alarm1State | 1.3.6.1.4.1.19011.1.3.1.1.4.3.5.2 | INTEGER | read-write | Setup the signal type to trigger alarm. |
| INT inSeptsensorConfigSensor1Alarm1Hysteresis | 1.3.6.1.4.1.19011.1.3.1.1.4.3.5.3 | INTEGER | read-write | The set value to delay the alarm triggered when event occurs. |
| inSeptsensorConfigSensor1Alarm2 | 1.3.6.1.4.1.19011.1.3.1.1.4.3.6 | |||
| STR inSeptsensorConfigSensor1Alarm2Name | 1.3.6.1.4.1.19011.1.3.1.1.4.3.6.1 | DisplayString | read-write | The name of alarm-1. |
| INT inSeptsensorConfigSensor1Alarm2State | 1.3.6.1.4.1.19011.1.3.1.1.4.3.6.2 | INTEGER | read-write | Setup the signal type to trigger alarm. |
| INT inSeptsensorConfigSensor1Alarm2Hysteresis | 1.3.6.1.4.1.19011.1.3.1.1.4.3.6.3 | INTEGER | read-write | The set value to delay the alarm triggered when event occurs. |
| inSeptsensorConfigSensor2 | 1.3.6.1.4.1.19011.1.3.1.1.4.4 | |||
| STR inSeptsensorConfigSensor2DeviceName | 1.3.6.1.4.1.19011.1.3.1.1.4.4.1 | DisplayString | read-write | The name of sensor device. |
| INT inSeptsensorConfigSensor2DeviceState | 1.3.6.1.4.1.19011.1.3.1.1.4.4.2 | INTEGER | read-write | The setup of sensor device type. |
| inSeptsensorConfigSensor2Temperature | 1.3.6.1.4.1.19011.1.3.1.1.4.4.3 | |||
| STR inSeptsensorConfigSensor2TemperatureName | 1.3.6.1.4.1.19011.1.3.1.1.4.4.3.1 | DisplayString | read-write | The temperature sensor name. |
| INT inSeptsensorConfigSensor2TemperatureLowWarning | 1.3.6.1.4.1.19011.1.3.1.1.4.4.3.2 | INTEGER | read-write | The set point to trigger low warning alarm. |
| INT inSeptsensorConfigSensor2TemperatureLowCritical | 1.3.6.1.4.1.19011.1.3.1.1.4.4.3.3 | INTEGER | read-write | The threshold to trigger low critical alarm. |
| INT inSeptsensorConfigSensor2TemperatureHighWarning | 1.3.6.1.4.1.19011.1.3.1.1.4.4.3.4 | INTEGER | read-write | The threshold to trigger high warning alarm. |
| INT inSeptsensorConfigSensor2TemperatureHighCritical | 1.3.6.1.4.1.19011.1.3.1.1.4.4.3.5 | INTEGER | read-write | The threshold to trigger high critical alarm. |
| INT inSeptsensorConfigSensor2TemperatureHysteresis | 1.3.6.1.4.1.19011.1.3.1.1.4.4.3.6 | INTEGER | read-write | The set value to prevent too many alarms when temperature is hovering around the set threshold. |
| INT inSeptsensorConfigSensor2TemperatureCalibration | 1.3.6.1.4.1.19011.1.3.1.1.4.4.3.7 | INTEGER | read-write | The set value to get the correct temperature according to your reference temperature. |
| INT inSeptsensorConfigSensor2TemperatureLowWarningStatus | 1.3.6.1.4.1.19011.1.3.1.1.4.4.3.8 | INTEGER | read-write | Enable/disable the set point to trigger low warning alarm. |
| INT inSeptsensorConfigSensor2TemperatureLowCriticalStatus | 1.3.6.1.4.1.19011.1.3.1.1.4.4.3.9 | INTEGER | read-write | Enable/disable the set point to trigger low critical alarm. |
| INT inSeptsensorConfigSensor2TemperatureHighWarningStatus | 1.3.6.1.4.1.19011.1.3.1.1.4.4.3.10 | INTEGER | read-write | Enable/disable the set point to trigger high warning alarm. |
| INT inSeptsensorConfigSensor2TemperatureHighCriticalStatus | 1.3.6.1.4.1.19011.1.3.1.1.4.4.3.11 | INTEGER | read-write | Enable/disable the set point to trigger high critical alarm. |
| inSeptsensorConfigSensor2Humidity | 1.3.6.1.4.1.19011.1.3.1.1.4.4.4 | |||
| STR inSeptsensorConfigSensor2HumdityName | 1.3.6.1.4.1.19011.1.3.1.1.4.4.4.1 | DisplayString | read-write | The humidity sensor name. |
| INT inSeptsensorConfigSensor2HumidityLowWarning | 1.3.6.1.4.1.19011.1.3.1.1.4.4.4.2 | INTEGER | read-write | The set point to trigger low warning alarm. |
| INT inSeptsensorConfigSensor2HumidityLowCritical | 1.3.6.1.4.1.19011.1.3.1.1.4.4.4.3 | INTEGER | read-write | The threshold to trigger low critical alarm. |
| INT inSeptsensorConfigSensor2HumidityHighWarning | 1.3.6.1.4.1.19011.1.3.1.1.4.4.4.4 | INTEGER | read-write | The threshold to trigger high warning alarm. |
| INT inSeptsensorConfigSensor2HumidityHighCritical | 1.3.6.1.4.1.19011.1.3.1.1.4.4.4.5 | INTEGER | read-write | The threshold to trigger high critical alarm. |
| INT inSeptsensorConfigSensor2HumidityHysteresis | 1.3.6.1.4.1.19011.1.3.1.1.4.4.4.6 | INTEGER | read-write | The set value to prevent too many alarms when Humidity is hovering around the set threshold. |
| INT inSeptsensorConfigSensor2HumidityCalibration | 1.3.6.1.4.1.19011.1.3.1.1.4.4.4.7 | INTEGER | read-write | The set value to get the correct temperature according to your reference temperature. |
| INT inSeptsensorConfigSensor2HumidityLowWarningStatus | 1.3.6.1.4.1.19011.1.3.1.1.4.4.4.8 | INTEGER | read-write | Enable/disable the set point to trigger low warning alarm. |
| INT inSeptsensorConfigSensor2HumidityLowCriticalStatus | 1.3.6.1.4.1.19011.1.3.1.1.4.4.4.9 | INTEGER | read-write | Enable/disable the set point to trigger low critical alarm. |
| INT inSeptsensorConfigSensor2HumidityHighWarningStatus | 1.3.6.1.4.1.19011.1.3.1.1.4.4.4.10 | INTEGER | read-write | Enable/disable the set point to trigger high warning alarm. |
| INT inSeptsensorConfigSensor2HumidityHighCriticalStatus | 1.3.6.1.4.1.19011.1.3.1.1.4.4.4.11 | INTEGER | read-write | Enable/disable the set point to trigger high critical alarm. |
| inSeptsensorConfigSensor2Alarm1 | 1.3.6.1.4.1.19011.1.3.1.1.4.4.5 | |||
| STR inSeptsensorConfigSensor2Alarm1Name | 1.3.6.1.4.1.19011.1.3.1.1.4.4.5.1 | DisplayString | read-write | The name of alarm-1. |
| INT inSeptsensorConfigSensor2Alarm1State | 1.3.6.1.4.1.19011.1.3.1.1.4.4.5.2 | INTEGER | read-write | Setup the signal type to trigger alarm. |
| INT inSeptsensorConfigSensor2Alarm1Hysteresis | 1.3.6.1.4.1.19011.1.3.1.1.4.4.5.3 | INTEGER | read-write | The set value to delay the alarm triggered when event occurs. |
| inSeptsensorConfigSensor2Alarm2 | 1.3.6.1.4.1.19011.1.3.1.1.4.4.6 | |||
| STR inSeptsensorConfigSensor2Alarm2Name | 1.3.6.1.4.1.19011.1.3.1.1.4.4.6.1 | DisplayString | read-write | The name of alarm-1. |
| INT inSeptsensorConfigSensor2Alarm2State | 1.3.6.1.4.1.19011.1.3.1.1.4.4.6.2 | INTEGER | read-write | Setup the signal type to trigger alarm. |
| INT inSeptsensorConfigSensor2Alarm2Hysteresis | 1.3.6.1.4.1.19011.1.3.1.1.4.4.6.3 | INTEGER | read-write | The set value to delay the alarm triggered when event occurs. |
| inSeptTraps | 1.3.6.1.4.1.19011.1.3.1.2 | |||
| NTF inSeptCommunicationRestored | 1.3.6.1.4.1.19011.1.3.1.2.0.1 | INFORMATION: Communication between interSeptor and sensor has been established. | ||
| NTF inSeptCommunicationLost | 1.3.6.1.4.1.19011.1.3.1.2.0.2 | WARNING: Communication between interSeptor and sensor has been lost. | ||
| NTF inSeptAlarm1Inactive | 1.3.6.1.4.1.19011.1.3.1.2.0.3 | INFORMATION: Alarm1 of sensor has returned from active state. | ||
| NTF inSeptAlarm1Active | 1.3.6.1.4.1.19011.1.3.1.2.0.4 | WARNING: Alarm1 has become active. | ||
| NTF inSeptAlarm2Inactive | 1.3.6.1.4.1.19011.1.3.1.2.0.5 | INFORMATION: Alarm2 of sensor has returned from active state. | ||
| NTF inSeptAlarm2Active | 1.3.6.1.4.1.19011.1.3.1.2.0.6 | WARNING: Alarm2 has become active. | ||
| NTF inSeptTemperatureNotHighWarning | 1.3.6.1.4.1.19011.1.3.1.2.0.7 | INFORMATION: The temperature of sensor has returned from High warning to normal. | ||
| NTF inSeptTemperatureHighWarning | 1.3.6.1.4.1.19011.1.3.1.2.0.8 | WARNING: The temperature of sensor is higher than High warning set point. | ||
| NTF inSeptTemperatureNotLowWarning | 1.3.6.1.4.1.19011.1.3.1.2.0.9 | INFORMATION: The temperature of sensor has returned from low warning to normal. | ||
| NTF inSeptTemperatureLowWarning | 1.3.6.1.4.1.19011.1.3.1.2.0.10 | WARNING: The temperature of sensor is lower than low warning set point. | ||
| NTF inSeptTemperatureNotHighCritical | 1.3.6.1.4.1.19011.1.3.1.2.0.11 | INFORMATION: The temperature of sensor is lower than high critical set point. | ||
| NTF inSeptTemperatureHighCritical | 1.3.6.1.4.1.19011.1.3.1.2.0.12 | CRITICAL: The temperature of sensor is higher than high critical set point. | ||
| NTF inSeptTemperatureNotLowCritical | 1.3.6.1.4.1.19011.1.3.1.2.0.13 | INFORMATION: The temperature of sensor is higher than low critical set point. | ||
| NTF inSeptTemperatureLowCritical | 1.3.6.1.4.1.19011.1.3.1.2.0.14 | CRITICAL: The temperature of sensor is lower than low critical set point. | ||
| NTF inSeptHumidityNotHighWarning | 1.3.6.1.4.1.19011.1.3.1.2.0.15 | INFORMATION: The humidity of sensor has returned from High warning to normal. | ||
| NTF inSeptHumidityHighWarning | 1.3.6.1.4.1.19011.1.3.1.2.0.16 | WARNING: The humidity of sensor is higher than High warning set point. | ||
| NTF inSeptHumidityNotLowWarning | 1.3.6.1.4.1.19011.1.3.1.2.0.17 | INFORMATION: The humidity of sensor has returned from low warning to normal. | ||
| NTF inSeptHumidityLowWarning | 1.3.6.1.4.1.19011.1.3.1.2.0.18 | WARNING: The humidity of sensor is lower than low warning set point. | ||
| NTF inSeptHumidityNotHighCritical | 1.3.6.1.4.1.19011.1.3.1.2.0.19 | INFORMATION: The humidity of sensor is lower than high critical set point. | ||
| NTF inSeptHumidityHighCritical | 1.3.6.1.4.1.19011.1.3.1.2.0.20 | CRITICAL: The humidity of sensor is higher than high critical set point. | ||
| NTF inSeptHumidityNotLowCritical | 1.3.6.1.4.1.19011.1.3.1.2.0.21 | INFORMATION: The humidity of sensor is higher than low critical set point. | ||
| NTF inSeptHumidityLowCritical | 1.3.6.1.4.1.19011.1.3.1.2.0.22 | CRITICAL: The humidity of sensor is lower than low critical set point. |
RFC description
Manages Jacarta InterSeptor environmental monitoring system including sensors, temperature, traps and access control.
Start monitoring InterSeptor/Jacarta security appliances with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.