ITOUCH-CHARACTER-MIB

All MIBs › ITOUCH-CHARACTER-MIB

Category: Vendor: iTouch

Description:

iTouch character-mode interface MIB providing SNMP objects for serial port and terminal character device management.

Imported Objects

AddressType
DateTime
iTouch	OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
TimeTicks

From RFC1213-MIB

DisplayString
sysLocation

From RFC1316-MIB

charPortIndex

OBJECT-TYPE

From RFC1317-MIB

rs232InSigState	OBJECT-TYPE
rs232OutSigState	OBJECT-TYPE
rs232PortIndex	OBJECT-TYPE

What Is ITOUCH-CHARACTER-MIB?

ITOUCH-CHARACTER-MIB is an iTouch Communications enterprise MIB for managing character-mode/serial console access devices, but its sample objects reveal it also covers environmental and power-outlet management typical of console-server/PDU-style hardware. It exposes contact-closure/alarm inputs, controllable power outlets (with on/off and reboot control, naming, and redundancy status), and temperature/humidity sensor data. Its core value is hardware status and control monitoring: reading temperature and humidity from basicTemperatureHumiditySensor, tracking whether a power outlet is on, off, or in a redundant configuration, and watching contact-closure alarm inputs for external fault conditions like an open door or water sensor. It is a self-contained vendor MIB, though it follows conventions common to environmental-monitoring/PDU MIBs in the console-server market. It is deployed on iTouch character-mode terminal servers/console access servers that include environmental sensors and switched power outlets, typically in data center or remote equipment closets. Engineers can download the ITOUCH-CHARACTER-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ITOUCH-CHARACTER-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

What Can Be Monitored

power outlet on/off state
power outlet redundancy status
remote outlet reboot capability
contact-closure/alarm inputs
temperature and humidity readings

Supported Devices

iTouch character-mode terminal/console servers with environmental sensors and switched PDU outlets

Monitoring Examples

An administrator polls basicPowerOutletTable (basicPowerOutletEntry) to check basicPowerOutletOnOff per basicPowerOutletName, and can invoke basicPowerOutletReboot to power-cycle a hung device attached to a specific outlet. basicContactClosureOrAlarmInputTable is watched for a triggered alarm input indicating an open cabinet door or leak sensor. basicTemperatureHumiditySensor readings, referenced against basicTemperatureUnits, are tracked to catch a rack overheating before attached equipment is damaged.

OIDs

OID symbolic	OID numeric	Type	Access	Description
NTF alarmMasterInputStateChange	1.3.6.1.4.1.33.0.41			Indication that the alarm input point within a high density alarm management port transitioned to open or closed.
NTF alarmMasterNotResponding	1.3.6.1.4.1.33.0.39			Indication that the high density alarm management device lost or regained contact with the inReach port to which it was connected as indicated by the basicPortAlarmMasterStatus variable.
NTF asciiToTrapTranslation	1.3.6.1.4.1.33.0.42			This trap contains ASCII data, which arrived at serial port, was formatted as a trap, and sent out on the network.
GAU basicActivePorts	1.3.6.1.4.1.33.13.1.10	Gauge	read-only	The number of ports with connected sessions or logged in users. Corresponds directly to the value labeled 'Active Ports:' and 'Cur' in the SERVER STATUS display.
GAU basicActivePortsHigh	1.3.6.1.4.1.33.13.1.11	Gauge	read-only	The highest value of basicActivePorts since system initialization. Corresponds directly to the value labeled 'Active Ports:' and 'High' in the SERVER STATUS display.
GAU basicActiveUsers	1.3.6.1.4.1.33.13.1.12	Gauge	read-only	The number of logged in users. Corresponds directly to the value labeled 'Active Users:' and 'Cur' in the SERVER STATUS display.
GAU basicActiveUsersHigh	1.3.6.1.4.1.33.13.1.13	Gauge	read-only	The highest value of basicActiveUsers since system initialization. Corresponds directly to the value labeled 'Active Users:' and 'High' in the SERVER STATUS display.
INT basicAlarmMasterControlOutputSignal	1.3.6.1.4.1.33.13.1.36.1.6	INTEGER	read-write	Control to toggle the output signal for an alarm point.
INT basicAlarmMasterDisplay	1.3.6.1.4.1.33.13.1.36.1.13	INTEGER	read-write	Control to toggle the display of the alarm status for this point in the display window of the high density alarm unit.
INT basicAlarmMasterInputDebounceInterval	1.3.6.1.4.1.33.13.1.36.1.8	INTEGER	read-write	Amount of time in seconds to debounce a signal change before triggering an alarm.
INT basicAlarmMasterInputEnable	1.3.6.1.4.1.33.13.1.36.1.7	INTEGER	read-write	Control to toggle whether this alarm point is active.
basicAlarmMasterInputEntry	1.3.6.1.4.1.33.13.1.36.1		not-accessible	An entry in the basicAlarmMasterInputTable.
INT basicAlarmMasterInputFaultSeverity	1.3.6.1.4.1.33.13.1.36.1.9	INTEGER	read-write	Control to determine the severity level associated with the trap sent out when a fault occurs for this alarm input point.
INT basicAlarmMasterInputFaultState	1.3.6.1.4.1.33.13.1.36.1.10	INTEGER	read-write	Control to indicate which state, open or closed, represents the fault condition for this alarm input point. The other state is the cleared condition.
STR basicAlarmMasterInputName	1.3.6.1.4.1.33.13.1.36.1.4	DisplayString	read-write	The name used to identify this alarm point.
INT basicAlarmMasterInputPoint	1.3.6.1.4.1.33.13.1.36.1.3	INTEGER	read-only	An index value that uniquely identifies an alarm point within an alarm slot on a high density alarm port.
INT basicAlarmMasterInputPort	1.3.6.1.4.1.33.13.1.36.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT basicAlarmMasterInputSlot	1.3.6.1.4.1.33.13.1.36.1.2	INTEGER	read-only	An index value that uniquely identifies a slot of alarm points on a given high density alarm port.
INT basicAlarmMasterInputStatus	1.3.6.1.4.1.33.13.1.36.1.11	INTEGER	read-only	Indicates the current status of the alarm input point. If the basicAlarmMasterInputValue matches the fault state, then the status is equal to the fault severity. Otherwise the status is cleared.
basicAlarmMasterInputTable	1.3.6.1.4.1.33.13.1.36		not-accessible	Information about the high density alarm manager's alarm inputs.
INT basicAlarmMasterInputTrapEnable	1.3.6.1.4.1.33.13.1.36.1.5	INTEGER	read-write	Control to send a trap when the alarm input changes state.
INT basicAlarmMasterInputValue	1.3.6.1.4.1.33.13.1.36.1.12	INTEGER	read-only	Indicates the current state of the alarm input point.
STR basicAutoProtocolDetectMessage	1.3.6.1.4.1.33.13.1.100	DisplayString	read-write	The text string sent as a prompt message out the port at the beginning of auto protocol detection mode. Corresponds to the value labeled 'APD Message' in the SERVER UNIT display.
INT basicBroadcast	1.3.6.1.4.1.33.13.1.1	INTEGER	read-write	Control for user ability to broadcast messages to other local ports. Corresponds directly to SERVER BROADCAST and the presence of the label 'Broadcast' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display.
INT basicConsoleLogoutDisconnect	1.3.6.1.4.1.33.13.1.19	INTEGER	read-write	Control for automatic session disconnection when a console port user logs out. Corresponds directly to SERVER CONSOLE LOGOUT and the presence of the label 'Console Logout' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display.
basicContactClosureOrAlarmInputEntry	1.3.6.1.4.1.33.13.1.25.1		not-accessible	An entry in the basicContactClosureOrAlarmInputTable.
INT basicContactClosureOrAlarmInputFaultSeverity	1.3.6.1.4.1.33.13.1.25.1.4	INTEGER	read-write	Control to determine the severity level associated with the trap sent out when a fault occurs for a given contact closure or alarm input.
INT basicContactClosureOrAlarmInputFaultState	1.3.6.1.4.1.33.13.1.25.1.5	INTEGER	read-write	Control to indicate which state, open or closed, represents the fault condition. The other state is the cleared condition.
INT basicContactClosureOrAlarmInputIndex	1.3.6.1.4.1.33.13.1.25.1.10	INTEGER	read-only	An index which uniquely identifies the contact closure or alarm input.
STR basicContactClosureOrAlarmInputManufacturer	1.3.6.1.4.1.33.13.1.25.1.11	DisplayString	read-write	The name used to identify the manufacturer of this equipment.
STR basicContactClosureOrAlarmInputModel	1.3.6.1.4.1.33.13.1.25.1.12	DisplayString	read-write	The model name of this equipment.
STR basicContactClosureOrAlarmInputName	1.3.6.1.4.1.33.13.1.25.1.2	DisplayString	read-write	The name used to identify this contact closure or alarm input.
STR basicContactClosureOrAlarmInputRelatedEquipment	1.3.6.1.4.1.33.13.1.25.1.8	DisplayString	read-write	The name used to identify related equipment.
STR basicContactClosureOrAlarmInputSiteId	1.3.6.1.4.1.33.13.1.25.1.9	DisplayString	read-write	The name used to identify the site where the unit resides.
INT basicContactClosureOrAlarmInputStatus	1.3.6.1.4.1.33.13.1.25.1.6	INTEGER	read-only	Indicates the current status of the contact closure or alarm input. If the basicContactClosureOrAlarmInputValue matches the fault state, then the status is equal to the fault severity. Otherwise the status is cleared.
basicContactClosureOrAlarmInputTable	1.3.6.1.4.1.33.13.1.25		not-accessible	Information about contact closures or alarm inputs.
INT basicContactClosureOrAlarmInputTrapEnable	1.3.6.1.4.1.33.13.1.25.1.3	INTEGER	read-write	Control to send trap when contact closure or alarm input changes state.
INT basicContactClosureOrAlarmInputValue	1.3.6.1.4.1.33.13.1.25.1.1	INTEGER	read-only	Indicates the state of the contact closure or alarm input.
STR basicContactClosureOrAlarmInputZone	1.3.6.1.4.1.33.13.1.25.1.7	DisplayString	read-write	The name used to identify the zone where the equipment resides.
INT basicControlledPorts	1.3.6.1.4.1.33.13.1.20	INTEGER	read-write	Status of Controlled Ports feature. Corresponds directly to the 'Controlled Ports' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. Enabling this feature causes strings of control characters to be sent out on a port upon starting and/or stopping a session
basicControlOutputEntry	1.3.6.1.4.1.33.13.1.30.1		not-accessible	An entry in the basicControlOutputTable.
INT basicControlOutputIndex	1.3.6.1.4.1.33.13.1.30.1.10	INTEGER	read-only	An index which uniquely identifies a distribution control signal point.
STR basicControlOutputName	1.3.6.1.4.1.33.13.1.30.1.2	DisplayString	read-write	The name used to identify this distribution control signal point.
basicControlOutputRelayEntry	1.3.6.1.4.1.33.13.1.38.1		not-accessible	An entry in the basicControlOutputRelayTable.
INT basicControlOutputRelayIndex	1.3.6.1.4.1.33.13.1.38.1.1	INTEGER	read-only	An index which uniquely identifies a control output relay.
STR basicControlOutputRelayName	1.3.6.1.4.1.33.13.1.38.1.2	DisplayString	read-write	The name used to identify this control output relay.
INT basicControlOutputRelayState	1.3.6.1.4.1.33.13.1.38.1.3	INTEGER	read-write	Controls the opening or closing of the control output relay.
INT basicControlOutputRelayStatus	1.3.6.1.4.1.33.13.1.38.1.4	INTEGER	read-only	Indicates the current status of the control output relay.
basicControlOutputRelayTable	1.3.6.1.4.1.33.13.1.38		not-accessible	Information about controlled output relays.
INT basicControlOutputSignalDtrRts	1.3.6.1.4.1.33.13.1.30.1.1	INTEGER	read-write	Controls the raising or lowering of a signal on a distribution control signal point. The signal is DTR when the basicControlOutputIndex is odd, or RTS when the basicControlOutputIndex is even.
basicControlOutputTable	1.3.6.1.4.1.33.13.1.30		not-accessible	Information about controlled output distribution points.
basicControlSignalEntry	1.3.6.1.4.1.33.13.1.28.1		not-accessible	An entry in the basicControlSignalTable.
INT basicControlSignalIndex	1.3.6.1.4.1.33.13.1.28.1.10	INTEGER	read-only	An index which uniquely identifies a control signal point.
basicControlSignalTable	1.3.6.1.4.1.33.13.1.28		not-accessible	Information about Environmental Manager Control Signal points.
INT basicControlSignalValue	1.3.6.1.4.1.33.13.1.28.1.1	INTEGER	read-write	Sets and reads the state of the control signal point.
INT basicEnvironmentalManagerCircuitBreaker	1.3.6.1.4.1.33.13.1.24	INTEGER	read-only	Indicates whether the circuit breaker is activated.
INT basicErrorReport	1.3.6.1.4.1.33.13.1.2	INTEGER	read-write	Control for server display of an error when the user gives an unsupported command. Corresponds directly to SERVER REPORT ERRORS and the presence of the label 'Report Errors' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display.
INT basicHumidityAlarmSeverity	1.3.6.1.4.1.33.13.1.27.2.1.5	INTEGER	read-write	Control to indicate the severity level associated with the trap sent out when the humidity reading is out-of-bounds.
INT basicHumidityAlarmStatus	1.3.6.1.4.1.33.13.1.27.2.1.6	INTEGER	read-only	Indicates the current status of the humidity sensor. If the basicHumidityValue falls within the normal range, the status is cleared. Otherwise the status matches the alarm severity level.
INT basicHumiditySensor	1.3.6.1.4.1.33.13.1.27.2.1.3	INTEGER	read-write	Controls the enabling or disabling of a humidity sensor.
basicHumiditySensorEntry	1.3.6.1.4.1.33.13.1.27.2.1		not-accessible	An entry in the basicHumiditySensorTable.
INT basicHumiditySensorIndex	1.3.6.1.4.1.33.13.1.27.2.1.10	INTEGER	read-only	An index which uniquely identifies a humidity sensor.
basicHumiditySensorTable	1.3.6.1.4.1.33.13.1.27.2		not-accessible	Information about Environmental Manager Humidity Sensors.
INT basicHumidityTrapHighThreshold	1.3.6.1.4.1.33.13.1.27.2.1.1	INTEGER	read-write	The humidity at or above which a sensorThresholdTrap is generated.
INT basicHumidityTrapLowThreshold	1.3.6.1.4.1.33.13.1.27.2.1.2	INTEGER	read-write	The humidity at or below which a sensorThresholdTrap is generated.
INT basicHumidityValue	1.3.6.1.4.1.33.13.1.27.2.1.4	INTEGER	read-write	The current humidity reading for this sensor.
INT basicInactivityTimer	1.3.6.1.4.1.33.13.1.4	INTEGER	read-write	Number of minutes a terminal may remain logged in with no sessions, no input or output, and no modem transitions. Corresponds directly to SERVER INACTIVITY TIMER and the value labeled 'Inactivity Timer:' in the SERVER CHARACTERISTICS display.
INT basicLock	1.3.6.1.4.1.33.13.1.3	INTEGER	read-write	Control for user ability to use a password to protect a logged in terminal from other users. Corresponds directly to SERVER LOCK and the presence of the label 'Lock' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display.
STR basicLoginPassword	1.3.6.1.4.1.33.13.1.7	DisplayString	read-write	The password a user must enter to be given the opportunity to log in. For security reasons, reading this object always returns a zero-length value. Corresponds directly to SERVER LOGIN PASSWORD.
STR basicLoginPrompt	1.3.6.1.4.1.33.13.1.8	DisplayString	read-write	The text string the server displays to prompt a user for the login password. Corresponds directly to SERVER LOGIN PROMPT.
INT basicPasswordRetryLimit	1.3.6.1.4.1.33.13.1.5	INTEGER	read-write	Number of times the server allows a user to retry an incorrect password. Corresponds directly to SERVER PASSWORD LIMIT and the value labeled 'Password Limit:' in the SERVER CHARACTERISTICS display.
STR basicPortActiveUserName	1.3.6.1.4.1.33.13.1.17.1.26	DisplayString	read-only	The user name currently logged into the port. Corresponds directly to the value by the port number and labeled 'Username' in the USERS display.
INT basicPortAlarmControl	1.3.6.1.4.1.33.13.1.17.1.49	INTEGER	read-write	Control to configure this port for alarm input and control output. This control is only valid on those models with variable configuration ports. This object can only be set enabled; and doing so will disable basicPortConsolePort and basicPortSensor. A set will only update the permanent database. Use a charPortReset for this change to take effect.
INT basicPortAlarmMaster	1.3.6.1.4.1.33.13.1.17.1.61	INTEGER	read-write	Control to configure this port for high densitiy alarm input and control output management. This control is only valid on those models with variable configuration ports. This object can only be set enabled; and doing so will disable basicPortConsolePort, basicPortSensor and basicPortAlarmControl. A set will only update the permanent database. Use a charPortReset for this change to take effect.
INT basicPortAlarmMasterAccounting	1.3.6.1.4.1.33.13.1.17.1.62	INTEGER	read-write	Control to toggle logging of alarm events on this port. Use a charPortReset for this change to take effect.
INT basicPortAlarmMasterAudibleAlarm	1.3.6.1.4.1.33.13.1.17.1.63	INTEGER	read-write	Control whether the alarm will have an audible sound for all alarm points attached to this port.
INT basicPortAlarmMasterFaultSeverity	1.3.6.1.4.1.33.13.1.17.1.71	INTEGER	read-write	Control to determine the severity level associated with the trap sent out when a fault occurs when no response is obtained from the high density alarm unit attached to this port.
INT basicPortAlarmMasterFixTime	1.3.6.1.4.1.33.13.1.17.1.64	INTEGER	read-write	Time in minutes between audible alarm soundings for an alarm master port. This occurs after someone hits the master alarm reset button. If there is at least one alarm condition on an alarm point within the fix time, then the alarm will sound again at the end of that fix time.
STR basicPortAlarmMasterLcdDisplayString	1.3.6.1.4.1.33.13.1.17.1.65	DisplayString	read-write	Updates the LCD display message for the high density alarm unit attached to the port. Corresponds directly to the DISPLAY AMST command.
INT basicPortAlarmMasterReboot	1.3.6.1.4.1.33.13.1.17.1.66	INTEGER	read-write	Control to reboot the high density alarm unit attached to the port when set to 'execute'. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Corresponds directly to the REBOOT AMST command.
INT basicPortAlarmMasterStatus	1.3.6.1.4.1.33.13.1.17.1.70	INTEGER	read-only	Indicates the current status of the high density alarm unit attached to the port. If no response is obtained from this unit, the status is set to basicPortAlarmMasterFaultSeverity. Otherwise it is cleared.
INT basicPortAlarmMasterUpdateFirmware	1.3.6.1.4.1.33.13.1.17.1.69	INTEGER	read-write	Control to update firmware for the high density alarm unit attached to the port when set to 'execute'. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. The basicPortAlarmMasterUpdateFirmwareHost and basicPortAlarmMasterUpdateFirmwareFileName must be set prior to setting this object. Corresponds directly to the UPDATE AMST FIRMWARE command.
STR basicPortAlarmMasterUpdateFirmwareFileName	1.3.6.1.4.1.33.13.1.17.1.68	DisplayString	read-write	The filename to request when downloading a new firmware image for the high density alarm unit attached to this port via TFTP. Corresponds directly to the UPDATE AMST FIRMWARE command's FILE parameter.
IP basicPortAlarmMasterUpdateFirmwareHost	1.3.6.1.4.1.33.13.1.17.1.67	IpAddress	read-write	The internet address of the server to use when downloading a new firmware image for the high density alarm unit attached to this port via TFTP. Corresponds directly to the UPDATE AMST FIRMWARE command's INTERNET ADDRESS parameter.
INT basicPortAsciiToTrapTranslation	1.3.6.1.4.1.33.13.1.17.1.79	INTEGER	read-write	Control to configure the port as an ascii-to-trap translator. One must log out the port for this change to take effect.
STR basicPortAsciiToTrapTranslationLastMessage	1.3.6.1.4.1.33.13.1.17.1.82	DisplayString	read-only	The last message or partial message sent out by this port.
CTR basicPortAsciiToTrapTranslationMessages	1.3.6.1.4.1.33.13.1.17.1.81	Counter	read-only	Count of number of trap messages sent from this port.
INT basicPortAsciiToTrapTranslationTrapSeverity	1.3.6.1.4.1.33.13.1.17.1.80	INTEGER	read-write	Control to determine the severity level associated with the trap sent out from this port. One must log out the port for this change to take effect.
INT basicPortAutoConnect	1.3.6.1.4.1.33.13.1.17.1.7	INTEGER	read-write	Control for automatic session connection. Corresponds directly to PORT AUTOCONNECT and the presence of the label 'Autoconnect' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortAutoLogin	1.3.6.1.4.1.33.13.1.17.1.8	INTEGER	read-write	Control for automatic port login. Corresponds directly to PORT AUTODEDICATED and the presence of the label 'Autodedicated' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
OCT basicPortBreakSequence	1.3.6.1.4.1.33.13.1.17.1.51	OCTET STRING	read-write	A sequence of characters to be sent out the serial port on receipt of a Break from the network in lieu of a hardware break.
INT basicPortBroadcast	1.3.6.1.4.1.33.13.1.17.1.9	INTEGER	read-write	Control for display of messages sent by users on other ports. Corresponds directly to PORT BROADCAST and the presence of the label 'Broadcast' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortCommandLogging	1.3.6.1.4.1.33.13.1.17.1.50	INTEGER	read-write	A control to toggle logging of commands at this port. Command input may be logged from direct terminal connections, session input from the LAN, or session output to the LAN. Corresponds directly to the presence of 'Command Logging' under the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. The desired change will not take effect until the port is logged off.
INT basicPortCommandLoggingSuppressControlCharacters	1.3.6.1.4.1.33.13.1.17.1.56	INTEGER	read-write	Control to toggle suppression of control characters in the command log. This object can only be set to enabled when command logging is enabled on that port.
INT basicPortConnectResume	1.3.6.1.4.1.33.13.1.17.1.10	INTEGER	read-write	Control for behavior of a connection attempt to a destination where the port already has a connection. 'disabled' causes a new connection. 'enabled' causes the existing connection to become the active connection. Corresponds directly to PORT CONNECTRESUME and the presence of the label 'Connectresume' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortConsolePort	1.3.6.1.4.1.33.13.1.17.1.46	INTEGER	read-write	Control to configure this port as a console port. This control is only valid on those models with variable configuration ports. This object can only be set enabled; and doing so will disable basicPortSensor and basicPortAlarmControl. A set will only update the permanent database. Use a charPortReset for this change to take effect.
OCT basicPortControlledPortLogin	1.3.6.1.4.1.33.13.1.17.1.34	OCTET STRING	read-write	A control string to send out the serial port upon port login. Corresponds to the hexadecimal code which is represented in ASCII following the label 'Controlled Port Login:' in the PORT CONTROLLED display.
OCT basicPortControlledPortLogout	1.3.6.1.4.1.33.13.1.17.1.35	OCTET STRING	read-write	A control string to send out the serial port upon port logout. Corresponds to the hexadecimal code which is represented in ASCII following the label 'Controlled Port Logout:' in the PORT CONTROLLED display.
OCT basicPortControlledSessionInitialize	1.3.6.1.4.1.33.13.1.17.1.36	OCTET STRING	read-write	A control string to send out the serial port upon entering a session. Corresponds to the hexadecimal code which represented in ASCII following the label 'Controlled Session Initialize:' in the PORT CONTROLLED display.
OCT basicPortControlledSessionTerminate	1.3.6.1.4.1.33.13.1.17.1.37	OCTET STRING	read-write	A control string to send out the serial port upon exiting a session. Corresponds to the hexadecimal code which is represented in ASCII following the label 'Controlled Session Terminate:' in the PORT CONTROLLED display.
INT basicPortDataLogging	1.3.6.1.4.1.33.13.1.17.1.57	INTEGER	read-write	Control to toggle data logging on the specified port.
INT basicPortDataLoggingSuppressControlCharacters	1.3.6.1.4.1.33.13.1.17.1.58	INTEGER	read-write	Control to toggle suppression of control characters in the data log. This object can only be set to enabled when data logging is enabled on that port.
OCT basicPortDefaultDedicatedSessionType	1.3.6.1.4.1.33.13.1.17.1.42	OCTET STRING	read-write	A bit mask that specifies the default session type for a dedicated service for this port. The bit numbers are: 1;service name, 2;node name, 3;port name, 4, telnet console; 5, rlogin; 6, bridge console; 7, chassis console.
INT basicPortDefaultDestAction	1.3.6.1.4.1.33.13.1.17.1.2	INTEGER	read-write	The action to take relative to basicPortDefaultDestName. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE and the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display.
INT basicPortDefaultDestControlled	1.3.6.1.4.1.33.13.1.17.1.33	INTEGER	read-write	A control to send preconfigured controlled port session strings when entering or exiting a session established to the basicPortDefaultDestName. Corresponds directly to the value labeled '(Controlled)' following the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display.
STR basicPortDefaultDestLATNodeName	1.3.6.1.4.1.33.13.1.17.1.5	DisplayString	read-write	A LAT node name to use with basicPortDefaultDestName. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE NODE and the value labeled 'Node:' following the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. This object can have a non- zero-length value only if the value of basicPortDefaultDestProtocol is 'lat'.
STR basicPortDefaultDestLATPortName	1.3.6.1.4.1.33.13.1.17.1.6	DisplayString	read-write	A LAT port name to use with basicPortDefaultDestName. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE NODE and the value labeled 'Node:' following the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. this object can hav a non-zero-length value only if the value if basicPortDefaultDestProtocol is 'lat'
STR basicPortDefaultDestName	1.3.6.1.4.1.33.13.1.17.1.4	DisplayString	read-write	The default name to use in forming a connection when no other name is specified. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE and the value labeled 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. If the value of basicPortDefaultDestProtocol is 'telnet', an Internet port number may be included on the end of the name, delimited with a colon (':'). If the value of basicPortDefaultDestProtocol is not 'telnet', then the maximum length is 16.
INT basicPortDefaultDestProtocol	1.3.6.1.4.1.33.13.1.17.1.3	INTEGER	read-write	The session protocol to use with basicPortDefaultDestName. Corresponds directly to LAT/TELNET PORT DEDICATED/PREFERRED SERVICE.
INT basicPortDefaultProtocol	1.3.6.1.4.1.33.13.1.17.1.19	INTEGER	read-write	The session protocol to use when not otherwise specified. Corresponds directly to PORT RESOLVE SERVICE and the value labeled 'Resolve Service:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicPortDefaultSessionMode	1.3.6.1.4.1.33.13.1.17.1.27	INTEGER	read-write	Data recognition mode when starting a session, with the following meanings: interactive locally recognize all controls binary recognize only session protocol (corresponds to PASSALL) binaryWithFlow recognize only XON and XOFF (corresponds to PASTHRU transparent recognize no data Corresponds directly to PORT DEFAULT SESSION MODE and the value labeled 'Default Session Mode:' in the PORT ALTERNATE CHARACTERISTICS display.
STR basicPortDefaultUserName	1.3.6.1.4.1.33.13.1.17.1.17	DisplayString	read-write	Default user name to use for automatically logging in the port. Corresponds directly to PORT USERNAME and the value labeled 'Port n:' in the PORT CHARACTERISTICS display.
INT basicPortDialup	1.3.6.1.4.1.33.13.1.17.1.11	INTEGER	read-write	Defines whether the port should be considered as connected to a dialup line. 'enabled' means that it is. Corresponds directly to PORT DIALUP and the presence of the label 'Dial Up' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
basicPortEntry	1.3.6.1.4.1.33.13.1.17.1		not-accessible	Basic parameter values for a port.
INT basicPortFallBack	1.3.6.1.4.1.33.13.1.17.1.60	INTEGER	read-write	Control to allow a 'fallback' authentication mechanism after RADIUS or SecurID authentication fails because the RADIUS or SecurID servers are unavailable. Onboard security, an internal security database, is used for fallback authentication. The user in fallback mode must enter a valid username and password to be successfully logged in. The change takes effect after logging out the port.
INT basicPortFallThrough	1.3.6.1.4.1.33.13.1.17.1.55	INTEGER	read-write	Control to allow a user to login to a port after RADIUS or SecurID authentication fails because the RADIUS servers or SecurID servers are unavailable. When a user is logged in via 'fallthrough', he is logged in to the port as a non-privileged user. The change takes effect after logging out the port.
INT basicPortIdleTimeout	1.3.6.1.4.1.33.13.1.17.1.12	INTEGER	read-write	The number of minutes the system will allow a session to have no activity before automatically disconnecting it. A value of -1 indicates no timeout. Zero is not a valid value. Corresponds directly to PORT IDLE TIMEOUT and the value labeled 'Idle Timeout:' in the PORT ALTERNATE CHARACTERISTICS display.
CTR basicPortIdleTimeouts	1.3.6.1.4.1.33.13.1.17.1.22	Counter	read-only	The number of session disconnects due to expiration of basicPortIdleTimeout. Corresponds directly to the value labeled 'Idle Timeouts:' in the PORT COUNTERS display.
INT basicPortIdleTimeReceive	1.3.6.1.4.1.33.13.1.17.1.43	INTEGER	read-write	Control to restrict the basicPortIdleTimeout to apply to data received from the network and transmitted out the serial port. Data received by the serial port will not be considered activity. Corresponds directly to the value labeled 'Idle Time Receive Mode:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicPortIdleTimeTransmit	1.3.6.1.4.1.33.13.1.17.1.44	INTEGER	read-write	Control to restrict the basicPortIdleTimeout to apply to data received from the serial port and transmitted out the LAN. Data received from the network will not count as activity. Corresponds directly to the value labeled 'Idle Time Transmit Mode:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicPortInactivityLogout	1.3.6.1.4.1.33.13.1.17.1.13	INTEGER	read-write	Control for the system automatically logging the port out when it has no sessions, no local activity, and no modem signal changes for the time period specified by basicInactivityTimer. Corresponds directly to PORT INACTIVITY LOGOUT and the presence of the label 'Inactivity Logout' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortIndex	1.3.6.1.4.1.33.13.1.17.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT basicPortLastInCharacter	1.3.6.1.4.1.33.13.1.17.1.24	INTEGER	read-only	The character that most recently came into the port. Corresponds directly to the value labeled 'Last Char Input:' in the PORT STATUS display.
INT basicPortLastOutCharacter	1.3.6.1.4.1.33.13.1.17.1.25	INTEGER	read-only	The character that most recently went out of the port. Corresponds directly to the value labeled 'Last Char Output:' in the PORT STATUS display.
INT basicPortLockout	1.3.6.1.4.1.33.13.1.17.1.78	INTEGER	read-write	Control to prohibit access to this port and send a trap when login authentication fails. One must log out the port for this change to take effect.
INT basicPortLoginDuration	1.3.6.1.4.1.33.13.1.17.1.39	INTEGER	read-write	The amount of time in minutes that a port may remain logged in regardless of the activity on the port. The value 0 indicates that the timer is disabled. Corresponds directly to the value labeled 'Login Duration:' in the PORT ALTERNATE CHARACTERISTICS display.
STR basicPortLoginPassword	1.3.6.1.4.1.33.13.1.17.1.47	DisplayString	read-write	The password a user must enter to be given the opportunity to log in to a given port. For security reasons reading this object always returns a zero-length value. Corresponds directly to PORT LOGIN PASSWORD.
CTR basicPortLogins	1.3.6.1.4.1.33.13.1.17.1.20	Counter	read-only	The number of logins on the port since system initialization. Corresponds directly to the value labeled 'Local Accesses:' in the PORT COUNTERS display.
INT basicPortLossNotification	1.3.6.1.4.1.33.13.1.17.1.14	INTEGER	read-write	Control for the system sending a Bell character to the port when it looses an input character due to an overrun or data error. Corresponds directly to PORT LOSS NOTIFICATION and the presence of the label 'Loss Notification' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortMessageCodes	1.3.6.1.4.1.33.13.1.17.1.15	INTEGER	read-write	Control for including error numbers in error messages displayed on the port. Corresponds directly to PORT MESSAGE CODES and the presence of the label 'Message Codes' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortMultisessions	1.3.6.1.4.1.33.13.1.17.1.16	INTEGER	read-write	Control for running the multisession line protocol between the port and the locally-connected terminal. Corresponds directly to PORT MULTISESSIONS and the presence of the label 'Multisessions' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortOnboardSecurity	1.3.6.1.4.1.33.13.1.17.1.59	INTEGER	read-write	A control to toggle onboard security for this port where the username and password are authenticated against an internal access list. The desired change will not take effect until the port is logged off.
INT basicPortOutboundSecurity	1.3.6.1.4.1.33.13.1.17.1.40	INTEGER	read-write	Control to disable outbound security, which can be either Kerberos or SecureID, on a per port basis. Corresponds directly to the presence of the value 'OutboundSecurity' following the label 'Enabled Characteristics' in the PORT CHARACTERISTICS display.
INT basicPortPortIndex	1.3.6.1.4.1.33.13.1.21.1.1	INTEGER	read-only	The value of basicPortIndex for the port to which this session belongs. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT basicPortPowerMaster	1.3.6.1.4.1.33.13.1.17.1.72	INTEGER	read-write	Control to configure this port as a power master port. This control is only valid on those models with variable configuration ports and which support the power master. This object can only be set enabled, and doing so will disable the previous port type, such as basicPortConsolePort. A set will only update the permanent database. Use a charPortReset for this change to take effect.
INT basicPortPowerMasterAlarmSeverity	1.3.6.1.4.1.33.13.1.17.1.83	INTEGER	read-write	Control to determine the severity level associated with the trap sent out when the power device is not responding to this port.
INT basicPortPowerMasterDeviceStatus	1.3.6.1.4.1.33.13.1.17.1.84	INTEGER	read-only	Indicates the current status of the power device controlled by this port. If the device is responding, the status is cleared. Otherwise the status matches the basicPortPowerMasterAlarmSeverity.
STR basicPortPowerMasterFirmware	1.3.6.1.4.1.33.13.1.17.1.77	DisplayString	read-only	The firmware version of the power master device, which is connected to this port.
STR basicPortPowerMasterModel	1.3.6.1.4.1.33.13.1.17.1.75	DisplayString	read-only	The model number of the power master device, which is connected to this port.
STR basicPortPowerMasterSerialNumber	1.3.6.1.4.1.33.13.1.17.1.76	DisplayString	read-only	The serial number of the power master device, which is connected to this port.
INT basicPortPowerMasterSwitch	1.3.6.1.4.1.33.13.1.17.1.74	INTEGER	read-write	Control to power on or off all of the outlets in the power device attached to this port. A get-request always returns ready.
INT basicPortPowerMasterTimeDelay	1.3.6.1.4.1.33.13.1.17.1.73	INTEGER	read-write	Control to set the power up delay interval in milliseconds for the power device attached to this port.
INT basicPortRemoteDisconnectNotify	1.3.6.1.4.1.33.13.1.17.1.32	INTEGER	read-write	If enabled, a BELL (ctrl G) will be sent out the serial port when a remote session is disconnected and the port is logged out.
CTR basicPortRemoteSessions	1.3.6.1.4.1.33.13.1.17.1.21	Counter	read-only	The number of remotely originating sessions to the port since system initialization. Corresponds directly to the value labeled 'Remote Accesses:' in the PORT COUNTERS display.
INT basicPortRloginTransparentMode	1.3.6.1.4.1.33.13.1.17.1.38	INTEGER	read-write	A control to pass x'ff' as binary data, not doubling x'ff'. Similar to basicPortSessionMode = transparent but for a rlogin session.
INT basicPortSensor	1.3.6.1.4.1.33.13.1.17.1.48	INTEGER	read-write	Control to configure this port as a temperature and humidity sensor. This control is only valid on those models with variable configuration ports. This object can only be set enabled; and doing so will disable basicPortConsolePort and basicPortAlarmControl. A set will only update the permanent database. Use a charPortReset for this change to take effect.
INT basicPortSessEncryption	1.3.6.1.4.1.33.13.1.22	INTEGER	read-write	Status of the default encryption value to be set for each session. Corresponds directly to Console Security on SHOW SERVER screen.
basicPortSessEntry	1.3.6.1.4.1.33.13.1.21.1		not-accessible	Status and parameter values for a basic port session.
INT basicPortSessIndex	1.3.6.1.4.1.33.13.1.21.1.2	INTEGER	read-only	The session index in the context of the port, a non-zero positive integer. Session indexes within a port need not be sequential. Session indexes may be reused for different ports. For example, port 1 and port 3 may both have a session 2 at the same time. Session indexes may have any valid integer value, with any meaning convenient to the agent implementation. The session identified by a particular value of this index is the same session as identified by charSessIndex in the standard Character MIB.
INT basicPortSessionMode	1.3.6.1.4.1.33.13.1.17.1.31	INTEGER	read-write	Data recognition mode for an active session, with the following meanings: interactive locally recognize all controls binary recognize only session protocol (corresponds to PASSALL) binaryWithFlow recognize only XON and XOFF (corresponds to PASTHRU transparent recognize no data noActiveSessions no sessions on this port. This object can be set to values of 1 to 4, but only if there is an active session on the port.
basicPortSessionTable	1.3.6.1.4.1.33.13.1.21		not-accessible	A list of port session entries.
INT basicPortSignalName	1.3.6.1.4.1.33.13.1.35.1.2	INTEGER	read-only	Identification of the hardware signal as specified in RFC1659 as follows: rts Request to Send cts Clear to Send dsr Data Set Ready dts Data Terminal Ready ri Ring Indicator dcd Received Line Signal Detector Some agents do not support DSR since its pin is shared with DCD.
INT basicPortStatus	1.3.6.1.4.1.33.13.1.17.1.23	INTEGER	read-only	The current operational status of the port. Corresponds directly to the value labeled 'Status:' in the PORT STATUS display.
basicPortTable	1.3.6.1.4.1.33.13.1.17		not-accessible	A list of basic character port entries.
INT basicPortTl1Console	1.3.6.1.4.1.33.13.1.17.1.54	INTEGER	read-write	Controls whether this port becomes the TL1 console receiving and displaying autonomous reports of alarm events. A change takes effect after logging out the port.
INT basicPortTl1Mode	1.3.6.1.4.1.33.13.1.17.1.53	INTEGER	read-write	Controls the TL1 mode of a port. Valid TL1 modes are human- to-machine language (hml), machine-to-machine language (mml), and MML without echo. MML is for direct connection to another TL1 device whereas HML provides human prompts. A change takes effect after logging out the port.
basicPortTrapEntry	1.3.6.1.4.1.33.13.1.35.1		not-accessible	Administrative status of signal change traps for a hardware port.
INT basicPortTrapIndex	1.3.6.1.4.1.33.13.1.35.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by rs232PortIndex in the standard rs232 MIB.
INT basicPortTrapStatus	1.3.6.1.4.1.33.13.1.35.1.3	INTEGER	read-write	Control to toggle the sending of a trap on a specific signal change on a physical port. One must logout the port prior to this taking effect.
basicPortTrapTable	1.3.6.1.4.1.33.13.1.35		not-accessible	A list of traps associated with signal control changes on ports.
INT basicPortUnixCommands	1.3.6.1.4.1.33.13.1.17.1.30	INTEGER	read-write	Control to allow the user to use Unix-style commands the port.
INT basicPortVerification	1.3.6.1.4.1.33.13.1.17.1.18	INTEGER	read-write	Control for display of informational messages on the port when the user connects, disconnects, or switches a session. Corresponds directly to PORT VERIFICATION and the presence of the label 'Verification' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortXonTimer	1.3.6.1.4.1.33.13.1.17.1.41	INTEGER	read-write	Indicates the number of seconds between successive 'XON's sent out a port. A zero signifies that the timer is disabled. Corresponds directly to the value labeled 'Xon Send Timer:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicPortZero	1.3.6.1.4.1.33.13.1.17.1.28	INTEGER	read-write	Control to zero counters for the port. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes the port's counters to be zeroed. Corresponds to the ZERO PORT command.
INT basicPortZeroDisconnectSession	1.3.6.1.4.1.33.13.1.17.1.45	INTEGER	read-write	A control to disconnect a session at Port 0 when the password limit is reached.
TIK basicPortZeroTime	1.3.6.1.4.1.33.13.1.17.1.29	TimeTicks	read-only	The number of hundredths of a second since the most recent zeroing of the port's counters, such as through execution of basicPortZero. Corresponds directly to the value labeled 'Seconds Since Zeroed:' in the PORT COUNTERS display.
INT basicPowerAlarmTimer	1.3.6.1.4.1.33.13.1.29	INTEGER	read-write	The polling interval in seconds for the fuse and power supply status. An alarm trap is issued on power failure.
STR basicPowerMasterOutletAmperageStatus	1.3.6.1.4.1.33.13.1.37.1.5	DisplayString	read-only	Indicates the current amperage drawn at this outlet. There may be a noticeable time delay while processing a get-request for this object.
basicPowerMasterOutletEntry	1.3.6.1.4.1.33.13.1.37.1		not-accessible	An entry in the basicPowerMasterOutletTable.
INT basicPowerMasterOutletIndex	1.3.6.1.4.1.33.13.1.37.1.2	INTEGER	read-only	An index which uniquely identifies a power master outlet.
STR basicPowerMasterOutletName	1.3.6.1.4.1.33.13.1.37.1.3	DisplayString	read-write	The name used to identify this power master outlet.
INT basicPowerMasterOutletState	1.3.6.1.4.1.33.13.1.37.1.4	INTEGER	read-write	Switches the power master outlet on or off. There may be a noticeable time delay while processing a get-request for this object.
basicPowerMasterOutletTable	1.3.6.1.4.1.33.13.1.37		not-accessible	Information about power master outlets.
INT basicPowerMasterPortIndex	1.3.6.1.4.1.33.13.1.37.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by the charPortIndex in the standard Character MIB.
STR basicPowerOutletConsoleName	1.3.6.1.4.1.33.13.1.26.1.5	DisplayString	read-write	A name used to identify a console port on a unit with power outlet managment.
basicPowerOutletEntry	1.3.6.1.4.1.33.13.1.26.1		not-accessible	An entry in the basicPowerOutletTable.
INT basicPowerOutletHighCurrent	1.3.6.1.4.1.33.13.1.26.1.6	INTEGER	read-write	A control to indicate a high current unit is attached to this power outlet. When enabled the high current unit will provide current when it detects no power from the power outlet; and will stop the current when the outlet resumes power. This control only works on those InReach devices which support the high current unit such as the IRMGR0. Corresponds directly to the value labeled 'HCNC Setting' in the INREACH MANAGER OUTLET STATUS display.
INT basicPowerOutletIndex	1.3.6.1.4.1.33.13.1.26.1.10	INTEGER	read-only	An index which uniquely identifies a power outlet.
STR basicPowerOutletName	1.3.6.1.4.1.33.13.1.26.1.3	DisplayString	read-write	A name used to identify this power outlet.
INT basicPowerOutletOnOff	1.3.6.1.4.1.33.13.1.26.1.1	INTEGER	read-write	Controls turning on or off the power for the device connected to this power outlet.
INT basicPowerOutletReboot	1.3.6.1.4.1.33.13.1.26.1.2	INTEGER	read-write	Controls rebooting of the device attached this power outlet.
INT basicPowerOutletRedundant	1.3.6.1.4.1.33.13.1.26.1.4	INTEGER	read-only	Controls whether power outlets in bank A have redundant outlets in bank B. When enabled, powering on an outlet in bank A will simultaneously power on the corresponding outlet number in bank B.
basicPowerOutletTable	1.3.6.1.4.1.33.13.1.26		not-accessible	Information about Environmental Manager Power Outlets.
INT basicPowerStatusFuseA	1.3.6.1.4.1.33.13.1.31	INTEGER	read-only	Indicates the status of fuse bank A.
INT basicPowerStatusFuseB	1.3.6.1.4.1.33.13.1.32	INTEGER	read-only	Indicates the status of fuse bank B.
INT basicPowerSupplyStatusA	1.3.6.1.4.1.33.13.1.33	INTEGER	read-only	Indicates the status of power supply A.
INT basicPowerSupplyStatusB	1.3.6.1.4.1.33.13.1.34	INTEGER	read-only	Indicates the status of power supply B.
STR basicPrivilegedPassword	1.3.6.1.4.1.33.13.1.6	DisplayString	read-write	The password a user must enter to become privileged. For security reasons, reading this object always returns a zero-length value. Corresponds directly to SERVER PRIVILEGED PASSWORD.
OCT basicSerialPortAPDDefaultProtocol	1.3.6.1.4.1.33.13.1.18.1.37	OCTET STRING	read-write	A bit map that specifies the protocol that this port will use when the time specified by basicSerialPortAPDTimeout has expired without sucessfully identifying the incoming porotocol. The bit numbers for the protocols are: None;Logout the port, 1;ARAP, 2;CSLIP, 3;Interactive, 4;SLIP, 5;PPP. Bits 6-16 are reserved for future use. Only one protocol may be specified for this object
OCT basicSerialPortAPDProtocols	1.3.6.1.4.1.33.13.1.18.1.35	OCTET STRING	read-write	A bit map that specifies the protocols that this port will attempt to detect using the Auto Protocol Detection function. The bit numbers for the protocols are: 1;ARAP, 3;Interactive, 4;SLIP, 5;PPP. Bits 6-16 are reserved for future use. More than one of these protocols may be ORed together. The default is 0 (zero) no protocols.
INT basicSerialPortAPDTimeout	1.3.6.1.4.1.33.13.1.18.1.36	INTEGER	read-write	A time value, in seconds, that specifies how long the port will attempt to determine which protocol is coming into the port. When basicSerialPortAPDTimeout seconds have expired, the port will assume the protocol to use is that specified by basicSerialPortAPDDefaultProtocol. A value of 0 (zero provides an unlimited timeout.
INT basicSerialPortAutoHangup	1.3.6.1.4.1.33.13.1.18.1.39	INTEGER	read-write	A control that, if enabled, will cause the port to be logged off when the last session on that port is destroyed
INT basicSerialPortAutoProtocolDetectPrompt	1.3.6.1.4.1.33.13.1.18.1.41	INTEGER	read-write	Controls whether to send the basicAutoProtocolDetectMessage out the serial port at the beginning of auto protocol detection mode. Corresponds to the value labeled 'APD Prompt' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortAutoProtocolDetectSecurityInteractiveOnly	1.3.6.1.4.1.33.13.1.18.1.44	INTEGER	read-write	Controls whether Auto Protocol Detect (APD) authentication applies only to interactive users, and not to other APD protocols such as PPP. Corresponds directly to the value labeled 'APD Authentication Interactive Only:' in the PORT CHARACTERISTICS display.
INT basicSerialPortBackwardSwitch	1.3.6.1.4.1.33.13.1.18.1.9	INTEGER	read-write	Character input from the character port to cause a switch to the previous, lower numbered session. The value 0 indicates no character has this effect. Corresponds directly to PORT BACKWARD SWITCH and the value labeled 'Backwards Switch:' in the PORT CHARACTERISTICS display.
INT basicSerialPortBreak	1.3.6.1.4.1.33.13.1.18.1.2	INTEGER	read-write	Action to take on a BREAK condition from the port. Corresponds directly to PORT BREAK and the value labeled 'Break:' in the PORT CHARACTERISTICS display.
INT basicSerialPortBreakLength	1.3.6.1.4.1.33.13.1.18.1.50	INTEGER	read-write	Specifies the duration in milliseconds of a remote serial break which is sent via the Telnet Break command. Corresponds directly to the value labeled 'Break Length:' in the PORT CHARACTERISTIC display.
INT basicSerialPortCommandSize	1.3.6.1.4.1.33.13.1.18.1.40	INTEGER	read-write	Maximum number of input characters to hold in the command buffer. Corresponds directly to the PORT COMMAND SIZE and the value labeled 'Command Size:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortDCDTimeout	1.3.6.1.4.1.33.13.1.18.1.16	INTEGER	read-write	The number of milleseconds that DCD may be asserted before disconnecting the port. Corresponds directly to PORT DCD TIMEOUT and the value labeled 'DCD Timeout:' in the PORT ALTERNATE CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
STR basicSerialPortDedicatedKickStartData	1.3.6.1.4.1.33.13.1.18.1.48	DisplayString	read-write	A text string which is used to compare at login time to incoming serial data. A match will initiate a telnet session to a dedicated service. Corresponds to the value labeled 'KickStart:' in the PORT CHARACTERISTICS display.
STR basicSerialPortDedicatedUserData	1.3.6.1.4.1.33.13.1.18.1.45	DisplayString	read-write	The text string to send at the beginning of a connection to a Telnet dedicated service. Corresponds to the value labeled 'UserData:' in the PORT CHARACTERISTICS display.
INT basicSerialPortDSRLogout	1.3.6.1.4.1.33.13.1.18.1.14	INTEGER	read-write	Control for logging out the port when DCD is deasserted. Corresponds directly to PORT DSRLOGOUT and the presence of the label 'DSRlogout' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortDSRObserve	1.3.6.1.4.1.33.13.1.18.1.15	INTEGER	read-write	Control for beginning the login sequence on the port when DCD is asserted. Corresponds directly to PORT DSRWAIT and the presence of the label 'DSRwait' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortDTRAssert	1.3.6.1.4.1.33.13.1.18.1.17	INTEGER	read-write	Control when the system asserts DTR on the port. always unconditional(DISABLED) onConnectionOrRing connection formed or RING asserted(ENABLED) onConnection connection formed (FORCONNECTION) onRing RING asserted (FORRING) Corresponds directly to PORT DTRWAIT and the value labeled 'DTR Wait:' in the PORT ALTERNATE CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
basicSerialPortEntry	1.3.6.1.4.1.33.13.1.18.1		not-accessible	Basic parameter values for a serial port.
INT basicSerialPortForwardSwitch	1.3.6.1.4.1.33.13.1.18.1.10	INTEGER	read-write	Character input from the character port to cause a switch to the next, higher numbered session. The value 0 indicates no character has this effect. Corresponds directly to PORT FORWARD SWITCH and the value labeled 'Forwards Switch:' in the PORT CHARACTERISTICS display.
INT basicSerialPortGatewayAutoDiscovery	1.3.6.1.4.1.33.13.1.18.1.53	INTEGER	read-write	Control to enable a non-standard method of acquiring the gateway address after boot completes via the bootp protocol.
INT basicSerialPortIndex	1.3.6.1.4.1.33.13.1.18.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT basicSerialPortInterrupts	1.3.6.1.4.1.33.13.1.18.1.3	INTEGER	read-write	Control for recognizing BREAK or local switch to interrupt a session. Corresponds directly to PORT INTERRUPTS and the presence of the label 'Interrupts' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicSerialPortIpAutoDiscovery	1.3.6.1.4.1.33.13.1.18.1.47	INTEGER	read-write	Control to enable a non-standard method of acquiring the IP address after boot completes via the BOOTP protocol. Corresponds to the value labeled 'IP Address Auto Discovery' in the SERVER CHARACTERISTICS display.
INT basicSerialPortIpConfigureBootp	1.3.6.1.4.1.33.13.1.18.1.57	INTEGER	read-write	Control to use the BOOTP protocol upon startup to learn the unit's own internet address, subnet mask, primary and secondary gateway servers, domain name servers, time server and domain name. This object was moved to the ITOUCH-INTERNET-MIB for InReach agent software version V2.4.
INT basicSerialPortLimitedCommands	1.3.6.1.4.1.33.13.1.18.1.18	INTEGER	read-write	Control for limiting the commands available to the user on the port. Corresponds directly to PORT SECURITY and the presence of the label 'Security' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortLimitedView	1.3.6.1.4.1.33.13.1.18.1.19	INTEGER	read-write	Control for restricting what a user may display. Corresponds directly to PORT LIMITED VIEW and the presence of the label 'Limited View' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicSerialPortLineEditor	1.3.6.1.4.1.33.13.1.18.1.21	INTEGER	read-write	Control for allowing the user to use local mode command line editing. Corresponds directly to PORT LINE EDITOR and the presence of the label 'Line Editor' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicSerialPortLineEditorBackspace	1.3.6.1.4.1.33.13.1.18.1.22	INTEGER	read-write	Character input from the character port to move the cursor to the left. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR BACKSPACE and the value labeled 'Backspace Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorBeginning	1.3.6.1.4.1.33.13.1.18.1.23	INTEGER	read-write	Character input from the character port to move the cursor to the beginning of the line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR BEGINNING and the value labeled 'Begin Line Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorCancel	1.3.6.1.4.1.33.13.1.18.1.24	INTEGER	read-write	Character input from the character port to cancel an interactive dialog or delete the current line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR CANCEL and the value labeled 'Cancel Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorDeleteBeginning	1.3.6.1.4.1.33.13.1.18.1.25	INTEGER	read-write	Character input from the character port to delete the current line from the cursor to the beginning. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR DELETE BEGINNING and the value labeled 'Delete Begin Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorDeleteLine	1.3.6.1.4.1.33.13.1.18.1.26	INTEGER	read-write	Character input from the character port to delete the current line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR DELETE LINE and the value labeled 'Delete Line Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorEnd	1.3.6.1.4.1.33.13.1.18.1.27	INTEGER	read-write	Character input from the character port to move the cursor to the end of the line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR END and the value labeled 'End of Line Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorForward	1.3.6.1.4.1.33.13.1.18.1.28	INTEGER	read-write	Character input from the character port to move the cursor to the right. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR FORWARDS and the value labeled 'Forwards Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorInsertToggle	1.3.6.1.4.1.33.13.1.18.1.29	INTEGER	read-write	Character input from the character port to toggle between insert and overwrite modes. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR INSERT TOGGLE and the value labeled 'Insert Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorNextLine	1.3.6.1.4.1.33.13.1.18.1.30	INTEGER	read-write	Character input from the character port to recall the next, newer line in the command history. The value -1 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR NEXT LINE and the value labeled 'Next Line Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorPreviousLine	1.3.6.1.4.1.33.13.1.18.1.31	INTEGER	read-write	Character input from the character port to recall the previous, older line in the command history. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR PREVIOUS LINE and the value labeled 'Previous Line Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorQuotingCharacter	1.3.6.1.4.1.33.13.1.18.1.32	INTEGER	read-write	Character input from the character port to inhibit interpretation of the next input character. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR QUOTING CHARACTER and the value labeled 'Quoting Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorRedisplay	1.3.6.1.4.1.33.13.1.18.1.33	INTEGER	read-write	Character input from the character port to redisplay the current command line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR REDISPLAY CHARACTER and the value labeled 'Redisplay Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLocalSwitch	1.3.6.1.4.1.33.13.1.18.1.11	INTEGER	read-write	Character input from the character port to cause a switch to local command mode. The value 0 indicates no character has this effect. Corresponds directly to PORT LOCAL SWITCH and the value labeled 'Local Switch:' in the PORT CHARACTERISTICS display.
INT basicSerialPortModemControl	1.3.6.1.4.1.33.13.1.18.1.12	INTEGER	read-write	Control for observing hardware modem control signals. Corresponds directly to PORT MODEM CONTROL and the value labeled 'Modem Control:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortNoLoss	1.3.6.1.4.1.33.13.1.18.1.4	INTEGER	read-write	Control for storing port input locally in anticipation of session startup. Corresponds directly to PORT NOLOSS and the presence of the label 'Noloss' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicSerialPortPassword	1.3.6.1.4.1.33.13.1.18.1.20	INTEGER	read-write	Control for requiring the user to supply the login password to log in on the port. Corresponds directly to PORT PASSWORD and the presence of the label 'Password' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
STR basicSerialPortPasswordPrompt	1.3.6.1.4.1.33.13.1.18.1.43	DisplayString	read-write	The text string used to prompt for a user's password. Corresponds directly to the value labeled 'Password Prompt:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortPause	1.3.6.1.4.1.33.13.1.18.1.5	INTEGER	read-write	Control for pausing after each screenful of locally-originated output to the port. Corresponds directly to PORT PAUSE and the presence of the label 'Pause' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
STR basicSerialPortPrompt	1.3.6.1.4.1.33.13.1.18.1.6	DisplayString	read-write	Prompt for the system to use on the port. Corresponds directly to PORT PROMPT and the value labeled 'Prompt:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortQuadartReceiveDiscard	1.3.6.1.4.1.33.13.1.18.1.34	INTEGER	read-write	Control for discard of received errors from quadart hardware.
INT basicSerialPortRaiseControlDtr	1.3.6.1.4.1.33.13.1.18.1.56	INTEGER	read-write	Controls the ability to change the state of DTR using basicSerialPortRaiseLowerDTR. This characteristic is not intended for use with modem ports. Corresponds directly to the presence of 'Control DTR' under the label 'Enabled Characteristics' in the PORT CHARACTERISTICS display. The desired change will not take effect until the port is logged off.
INT basicSerialPortRaiseLowerDtr	1.3.6.1.4.1.33.13.1.18.1.55	INTEGER	read-write	A control to to raise or lower the DTR signal from this port by setting it to high or low, respectively. This request will have no effect unless basicSerialPortRaiseControlDtr is enabled. In response to a get-request or get-next-request the agent always returns low for this object.
INT basicSerialPortRotaryRoundRobin	1.3.6.1.4.1.33.13.1.18.1.51	INTEGER	read-write	Controls whether a port which participates in an internet rotary is selected in round robin or fixed priority order. Corresponds directly to the value labeled 'Round Robin search:' in the SERVER INTERNET ROTARY display.
INT basicSerialPortSignalCheck	1.3.6.1.4.1.33.13.1.18.1.13	INTEGER	read-write	Control for observing DSR and DCD to bound allowing sessions. Corresponds directly to PORT SIGNAL CHECK and the presence of the label 'Signal Check' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortSubnetAutoDiscovery	1.3.6.1.4.1.33.13.1.18.1.54	INTEGER	read-write	Control to enable a non-standard method of acquiring the subnet mask after boot completes via the bootp protocol.
basicSerialPortTable	1.3.6.1.4.1.33.13.1.18		not-accessible	A list of basic character serial port entries.
INT basicSerialPortTerminalType	1.3.6.1.4.1.33.13.1.18.1.7	INTEGER	read-write	Type of terminal attached to the port, for formatting local output. Corresponds directly to PORT TYPE and the value labeled 'Type:' in the PORT CHARACTERISTICS display.
INT basicSerialPortTypeaheadLimit	1.3.6.1.4.1.33.13.1.18.1.8	INTEGER	read-write	Maximum number of input characters to hold pending tranmission on a session. Corresponds directly to PORT TYPEAHEAD SIZE and the value labeled 'Typeahead Size:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortUsernameCharSet	1.3.6.1.4.1.33.13.1.18.1.38	INTEGER	read-write	A control, that if set to seven-bit, will allow only the ASCII printable characters in the range SP (X20) to ~ (X7E) in the username field. A value of none allows any character
STR basicSerialPortUsernamePrompt	1.3.6.1.4.1.33.13.1.18.1.42	DisplayString	read-write	The text string used to prompt for a user's name. Corresponds directly to the value labeled 'Username Prompt:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortWelcomeBeforeAuthentication	1.3.6.1.4.1.33.13.1.18.1.52	INTEGER	read-write	Control to display the basicWelcome message prior to authenticating the user. Corresponds to the presence of the value 'Welcome-Banner-Pre-Authentication' following the label 'Enabled Characteristics' in the PORT CHARACTERISTICS display.
INT basicSessControlled	1.3.6.1.4.1.33.13.1.21.1.3	INTEGER	read-only	A control to send preconfigured controlled port session strings out the serial port when entering or exiting this session. Corresponds directly to the value labeled 'Controlled' under the Service Mode header in the SESSION display.
GAU basicSessions	1.3.6.1.4.1.33.13.1.14	Gauge	read-only	The total number of connected sessions. Corresponds directly to the value labeled 'Connected Sessions:' and 'Cur' in the SERVER STATUS display.
GAU basicSessionsHigh	1.3.6.1.4.1.33.13.1.15	Gauge	read-only	The highest value of basicSessions since system initialization. Corresponds directly to the value labeled 'Connected Sessions:' and 'High' in the SERVER STATUS display.
INT basicSessionsLimit	1.3.6.1.4.1.33.13.1.16	INTEGER	read-write	The maximum total number of sessions that can simultaneously be connected to the system. A value of -1 indicates no limit up to available dynamic system memory. Corresponds directly to SERVER SESSION LIMIT and the value labeled 'Connected Sessions:' and 'Max' in the SERVER STATUS display.
INT basicTemperatureAlarmSeverity	1.3.6.1.4.1.33.13.1.27.1.1.5	INTEGER	read-write	Control to determine the severity level associated with the trap sent out when the temperature reading is out-of-bounds.
INT basicTemperatureAlarmStatus	1.3.6.1.4.1.33.13.1.27.1.1.6	INTEGER	read-only	Indicates the current status of the temperature sensor. If the basicTemperatureValue falls within the normal range, the status is cleared. Otherwise the status matches the alarm severity level.
basicTemperatureHumiditySensor	1.3.6.1.4.1.33.13.1.27
INT basicTemperatureSensor	1.3.6.1.4.1.33.13.1.27.1.1.3	INTEGER	read-write	Controls the enabling or disabling of a temperature sensor.
basicTemperatureSensorEntry	1.3.6.1.4.1.33.13.1.27.1.1		not-accessible	An entry in the basicTemperatureSensorTable.
INT basicTemperatureSensorIndex	1.3.6.1.4.1.33.13.1.27.1.1.10	INTEGER	read-only	An index which uniquely identifies a temperature sensor.
basicTemperatureSensorTable	1.3.6.1.4.1.33.13.1.27.1		not-accessible	Information about Environmental Manager Temperature Sensors.
INT basicTemperatureUnits	1.3.6.1.4.1.33.13.1.23	INTEGER	read-write	Indicates the units of measurement for the temperature sensors.
INT basicTemperatureValue	1.3.6.1.4.1.33.13.1.27.1.1.4	INTEGER	read-write	The current temperature reading for this sensor.
INT basicTempTrapHighThreshold	1.3.6.1.4.1.33.13.1.27.1.1.1	INTEGER	read-write	The temperature at or above which a sensorThresholdTrap is generated.
INT basicTempTrapLowThreshold	1.3.6.1.4.1.33.13.1.27.1.1.2	INTEGER	read-write	The temperature at or below which a sensorThresholdTrap is generated.
STR basicWelcome	1.3.6.1.4.1.33.13.1.9	DisplayString	read-write	The text string the server displays before attempting to log in a user. Corresponds directly to SERVER WELCOME and the value labeled 'Welcome:' in the SERVER CHARACTERISTICS display.
broadcastGroupEntry	1.3.6.1.4.1.33.13.8.1.1		not-accessible	Broadcast group information.
INT broadcastGroupIndex	1.3.6.1.4.1.33.13.8.1.1.1	INTEGER	read-only	An index value that uniquely identifies a broadcast group.
INT broadcastGroupMaster	1.3.6.1.4.1.33.13.8.1.1.3	INTEGER	read-write	An index value that uniquely identifies the Master Broadcast Port for this group. The port provided in this object is the same port as identified by charPortIndex in the standard Character MIB.
OCT broadcastGroupSlaves	1.3.6.1.4.1.33.13.8.1.1.4	OCTET STRING	read-write	A bitmap representing the ports included in this broadcast group. A bit with a value of '1' means the corresponding port is included in the broadcast group whereas a value of '0' indicates that the port is not part of the broadcast group.
OCT broadcastGroupSlavesBroadcastOnly	1.3.6.1.4.1.33.13.8.1.1.5	OCTET STRING	read-write	A bitmap representing the ports set up to discard input data and transmit only the broadcast data on the line. A bit set to '1' means that the corresponding port will only broadcast the data and discard any input.
INT broadcastGroupSlaveTcpBroadcastOnly	1.3.6.1.4.1.33.13.8.1.1.7	INTEGER	read-write	Specifies whether the TCP port will discard input characters for the Master port so that the Master port operates in broadcast only mode.
INT broadcastGroupSlaveTcpPort	1.3.6.1.4.1.33.13.8.1.1.6	INTEGER	read-write	A TCP port number on which the broadcast group process will listen for incoming TCP connections. A client connected to this particular port will receive the data broadcast by the Master Port. A value of '0' indicates that no TCP port is defined.
INT broadcastGroupStatus	1.3.6.1.4.1.33.13.8.1.1.2	INTEGER	read-write	A status value for the broadcast group. The value 'enabled' means that the group is active and broadcasting data whereas 'disabled' means that the group is not active.
broadcastGroupTable	1.3.6.1.4.1.33.13.8.1		not-accessible	A list of broadcast groups.
cclParsedScriptEntry	1.3.6.1.4.1.33.13.7.1.1		not-accessible	Parsed CCL script information.
cclParsedScriptTable	1.3.6.1.4.1.33.13.7.1		not-accessible	A list of parsed CCL scripts.
STR cclPortCclName	1.3.6.1.4.1.33.13.7.2.1.1	DisplayString	read-write	The name of the ARAP modem CCL script file.
cclPortEntry	1.3.6.1.4.1.33.13.7.2.1		not-accessible	CCL parameter values for a port.
INT cclPortModemAudible	1.3.6.1.4.1.33.13.7.2.1.2	INTEGER	read-write	This boolean indicates if the CCL script should put the modem into audible mode.
cclPortTable	1.3.6.1.4.1.33.13.7.2		not-accessible	A list of ccl character port entries.
INT cclScriptControl	1.3.6.1.4.1.33.13.7.1.1.2	INTEGER	read-write	Control for maintaining the CCL script. The refresh action consists of retrieving the script by name from a script server and parsing it into an executable format. This may be used to add an entry to the table or refresh an existing entry with a new version of the CCL script from the server. This command may take ten seconds or more to complete and may fail if the script file cannot be retrieved or an error is encountered in parsing the CCL script. An error value of genErr is returned upon refresh failure. The refresh action corresponds directly to the commnd: REFRESH SERVER CCL. Setting this field to delete causes a script that is NOT being referenced by any ports to be removed from the list and its memory freed. This action corresponds directly to the command: DELETE SERVER CCL. An error value of badValue is returned upon delete failure.
STR cclScriptName	1.3.6.1.4.1.33.13.7.1.1.1	DisplayString	read-only	The name of a CCL script file that has been loaded from a script server. Corresponds directly to the name in a SERVER CCL command and the value labeled 'CCL name:' in the PORT CHARACTERISTICS display.
characterDep	1.3.6.1.4.1.33.2
NTF contactClosureChanged	1.3.6.1.4.1.33.0.30			Indication that the contact closure transitioned to open or closed.
INT dialPortDialback	1.3.6.1.4.1.33.13.5.1.1.2	INTEGER	read-write	Control for use of dialback when a user logs in on the port. Corresponds directly to PORT DIALBACK and the presence of the label 'Dialback' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT dialPortDialbackNoUsername	1.3.6.1.4.1.33.13.5.1.1.5	INTEGER	read-write	Control which when enabled on a dialback port will not prompt for a username upon dialing back. Instead the original username is reused.
INT dialPortDialbackTimeout	1.3.6.1.4.1.33.13.5.1.1.3	INTEGER	read-write	The number of seconds to wait for remote modem response when dialing back. Corresponds directly to PORT DIALBACK TIMEOUT and the value labeled 'Dialback Timeout:' in the PORT ALTERNATE CHARACTERISTICS display.
INT dialPortDialout	1.3.6.1.4.1.33.13.5.1.1.4	INTEGER	read-write	A control to determine the state of a remote port after it has been logged out from the remote side of the connection. none will log out the port, query will ask user what to do, slip and ppp will revert to those protocols
dialPortEntry	1.3.6.1.4.1.33.13.5.1.1		not-accessible	Dial parameter values for a port.
INT dialPortIndex	1.3.6.1.4.1.33.13.5.1.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
dialPortTable	1.3.6.1.4.1.33.13.5.1		not-accessible	A list of dial character port entries.
NTF humidityThresholdExceeded	1.3.6.1.4.1.33.0.37			Indication that the humidity exceeded a threshhold and the value of the currrent humidity.
STR menuCommand	1.3.6.1.4.1.33.13.3.4.1.4	DisplayString	read-write	The commands to execute when the user chooses the menu entry. Corresponds directly second line following the entry number in the SERVER MENU display.
STR menuContinuePrompt	1.3.6.1.4.1.33.13.3.2	DisplayString	read-write	The text to use when prompting a menu user to press RETURN to continue. Corresponds directly to SERVER MENU CONTINUE PROMPT and the value labeled 'Menu Continue Prompt:' in the SERVER MENU display.
menuEntry	1.3.6.1.4.1.33.13.3.4.1		not-accessible	Parameter values for a menu entry.
INT menuIndex	1.3.6.1.4.1.33.13.3.4.1.1	INTEGER	read-only	The index number of a menu entry. Corresponds directly to the numbers down the left of the SERVER MENU display.
INT menuNestedEthernet	1.3.6.1.4.1.33.13.3.9	INTEGER	read-write	Control to request to download a menu script which is unique for this unit by prepending the Ethernet address, or 802.3 MAC address, of this unit to the nestedMenuName.
STR menuNestedName	1.3.6.1.4.1.33.13.3.6	DisplayString	read-write	Name of the script file containing the nested menu.
INT menuNestedScriptMaximum	1.3.6.1.4.1.33.13.3.7	INTEGER	read-write	Maximum number of temporary storage bytes for a nested menu script file. If not zero, the nested menu function is enabled.
INT menuNestedSystemName	1.3.6.1.4.1.33.13.3.8	INTEGER	read-write	Control to request to download a menu script which is unique for this unit by prepending the sysLocalName of this unit to the nestedMenuName.
GAU menuNumber	1.3.6.1.4.1.33.13.3.1	Gauge	read-only	The number of entries in the Menu table. Corresponds indirectly to SERVER MENU display.
menuPortEntry	1.3.6.1.4.1.33.13.3.5.1		not-accessible	Menu parameter values for a port.
INT menuPortIndex	1.3.6.1.4.1.33.13.3.5.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT menuPortMenuStatus	1.3.6.1.4.1.33.13.3.5.1.2	INTEGER	read-write	Control for menu operation on the port. Corresponds indirectly to PORT MENU and PORT PRIVILEGED MENU and the presence of the labels 'Menu' and 'Privileged Menu' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT menuPortNestedMenuPrivilege	1.3.6.1.4.1.33.13.3.5.1.4	INTEGER	read-write	Control for nested privileged menu operation on the port. Corresponds indirectly to PORT NESTED PRIVILEGED MENU and the presence of the label 'Nested Privileged Menu' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT menuPortNestedMenuStatus	1.3.6.1.4.1.33.13.3.5.1.3	INTEGER	read-write	Control for nested menu operation on the port. Corresponds indirectly to PORT NESTED MENU and the presence of the label 'Nested Menu' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT menuPortNestedTopLevel	1.3.6.1.4.1.33.13.3.5.1.5	INTEGER	read-write	The top level nested menu to select from the menu definition file.
menuPortTable	1.3.6.1.4.1.33.13.3.5		not-accessible	A list of menu-related character port entries.
STR menuSelectionPrompt	1.3.6.1.4.1.33.13.3.3	DisplayString	read-write	The text to use when prompting a menu user for a menu selection. Corresponds directly to SERVER MENU PROMPT and the value labeled 'Menu Prompt:' in the SERVER MENU display.
INT menuStatus	1.3.6.1.4.1.33.13.3.4.1.2	INTEGER	read-write	The status of a the entry. Set to 'invalid' to remove the entry, which corresponds directly to the CLEAR SERVER MENU command. Actual removal of the entry is implementation specific.
menuTable	1.3.6.1.4.1.33.13.3.4		not-accessible	A list of menu entries.
STR menuText	1.3.6.1.4.1.33.13.3.4.1.3	DisplayString	read-write	The text to be displayed in the menu. Corresponds directly to the line next to the entry number in the SERVER MENU display.
INT netLoginNumber	1.3.6.1.4.1.33.13.4.1	INTEGER	read-only	The number of entries in the Network Login Server table.
netLoginPortEntry	1.3.6.1.4.1.33.13.4.3.1		not-accessible	Network login parameter values for a port.
STR netLoginPortExecuteFile	1.3.6.1.4.1.33.13.4.3.1.7	DisplayString	read-write	The path and file name of a script to be executed immediately on the port. Corresponds directly the file name in the SCRIPT command.
INT netLoginPortIndex	1.3.6.1.4.1.33.13.4.3.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
OCT netLoginPortLoaderAddress	1.3.6.1.4.1.33.13.4.3.1.5	OCTET STRING	read-only	The network address of the server that provided the script for the current port login. Corresponds directly the address part of the value labeled 'Script Loaded From:' in the PORT STATUS display.
ADR netLoginPortLoaderAddressType	1.3.6.1.4.1.33.13.4.3.1.4	AddressType	read-only	The type of network address contained in netLoginPortLoaderAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. Corresponds indirectly to the address part of the value labeled 'Script Loaded From:' in the PORT STATUS display.
STR netLoginPortLoaderFile	1.3.6.1.4.1.33.13.4.3.1.6	DisplayString	read-only	The path and file name of the script used for the current port login. Corresponds directly the file name part of the value labeled 'Script Loaded From:' in the PORT STATUS display.
INT netLoginPortScriptEcho	1.3.6.1.4.1.33.13.4.3.1.3	INTEGER	read-write	Control for display of script operation on the port when running a script. Corresponds directly to PORT SCRIPT ECHO and the presence of the label 'Script Echo' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT netLoginPortScriptUse	1.3.6.1.4.1.33.13.4.3.1.2	INTEGER	read-write	Control for the script action taken when a user logs in on the port. Corresponds directly to PORT SCRIPT LOGIN and the value labeled 'Script Login:' in the PORT ALTERNATE CHARACTERISTICS display.
netLoginPortTable	1.3.6.1.4.1.33.13.4.3		not-accessible	A list of network login character port entries.
netLoginServerEntry	1.3.6.1.4.1.33.13.4.2.1		not-accessible	Network login parameter values for a server entry.
STR netLoginServerName	1.3.6.1.4.1.33.13.4.2.1.1	DisplayString	read-only	The name of a network login server, suitable for resolution to a network address. Corresponds directly to host portion of SERVER SCRIPT SERVER and the value labeled 'Script Host' in the SERVER PARAMETER SERVER display.
STR netLoginServerPath	1.3.6.1.4.1.33.13.4.2.1.3	DisplayString	read-write	The full path name to the script file that is identified by the user name. Corresponds directly to path portion of SERVER SCRIPT SERVER and the value labeled 'Script Path' in the SERVER PARAMETER SERVER display. Defaults to the NULL string when a new entry is created.
STR netLoginServerSeparator	1.3.6.1.4.1.33.13.4.2.1.4	DisplayString	read-write	The single character string that will be inserted between the components of a file's path on the script server. Defaults to the NULL string when a new entry is created. Corresponds directly to the separator portion of SERVER SCRIPT SERVER display.
INT netLoginServerStatus	1.3.6.1.4.1.33.13.4.2.1.2	INTEGER	read-write	Status of this entry. Set to 'invalid' to remove the entry, which corresponds directly to the CLEAR SERVER SCRIPT SERVER command. Actual removal of the entry is implementation specific.
netLoginServerTable	1.3.6.1.4.1.33.13.4.2		not-accessible	A list of network login server entries.
NTF portInputSignalChange	1.3.6.1.4.1.33.0.35			Indicates that an input signal on a port has transitioned to the state indicated in the variable rs232InSigState.
NTF portOutputSignalChange	1.3.6.1.4.1.33.0.36			Indicates that an output signal on a port has transitioned to the state indicated in the variable rs232OutSigState.
NTF powerAlarmFuseBankA	1.3.6.1.4.1.33.0.31			Indicates that a fuse from bank A tripped its breaker, or that it went operational. However, it is unlikely that a trap would be issued when the fuse starts working.
NTF powerAlarmFuseBankB	1.3.6.1.4.1.33.0.32			Indicates that a fuse from bank B tripped its breaker, or that it went operational. However, it is unlikely that a trap would be issued when the fuse starts working.
NTF powerMasterNotResponding	1.3.6.1.4.1.33.0.43			Indication that the power management port lost or regained contact with the power unit to which it was connected as indicated by the basicPortPowerMasterDeviceStatus variable.
NTF powerSupplyAlarmA	1.3.6.1.4.1.33.0.33			Indicates that power supply A lost or regained power. However, it is unlikely that a trap would be issued when the power comes on.
NTF powerSupplyAlarmB	1.3.6.1.4.1.33.0.34			Indicates that power supply B lost or regained power. However, it is unlikely that a trap would be issued when the power comes on.
queueEntry	1.3.6.1.4.1.33.13.2.4.1		not-accessible	Parameter values for a queue entry.
GAU queueHigh	1.3.6.1.4.1.33.13.2.2	Gauge	read-only	The highest value of queueNumber since system initialization. Corresponds directly to the value labeled 'Queue Entries' and 'High' in the SERVER STATUS display.
INT queueJob	1.3.6.1.4.1.33.13.2.4.1.1	INTEGER	read-only	The job number of a queued request. Corresponds directly to the value labeled 'Entry' in the QUEUE display.
INT queueLimit	1.3.6.1.4.1.33.13.2.1	INTEGER	read-write	The maximum number of entries that can be made in the Queue table. The value -1 indicates the imit is available memory. Corresponds directly to SERVER QUEUE LIMIT and the value labeled 'Queue Limit:' in the SERVER CHARACTERISTICS display.
GAU queueNumber	1.3.6.1.4.1.33.13.2.3	Gauge	read-only	The number of entries in the Queue table. Corresponds directly to the value labeled 'Queue Entries' and 'Cur' in the SERVER STATUS display.
queuePortEntry	1.3.6.1.4.1.33.13.2.5.1		not-accessible	Queuing parameter values for a port.
INT queuePortIndex	1.3.6.1.4.1.33.13.2.5.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT queuePortQueuing	1.3.6.1.4.1.33.13.2.5.1.2	INTEGER	read-write	Control for allowing queued requests for using the port. Corresponds directly to PORT QUEUING and the presence of the label 'Queuing' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
queuePortTable	1.3.6.1.4.1.33.13.2.5		not-accessible	A list of queuing-related character port entries.
STR queueServiceName	1.3.6.1.4.1.33.13.2.4.1.4	DisplayString	read-only	The name of the service for which the originator is waiting. Corresponds directly to the value labeled 'Service' in the QUEUE display.
INT queueServicePortIndex	1.3.6.1.4.1.33.13.2.4.1.5	INTEGER	read-only	The charPortIndex of the port for which the originator is waiting, if supplied by the originator. As defined in the standard Character MIB. Corresponds indirectly to the port number part of the value labeled 'Port Name' in the QUEUE display.
STR queueServicePortName	1.3.6.1.4.1.33.13.2.4.1.6	DisplayString	read-only	The name of the port for which the originator is waiting, if supplied by the originator. Corresponds directly to the port name part of the value labeled 'Port Name' in the SERVER QUEUE display.
STR queueSourceName	1.3.6.1.4.1.33.13.2.4.1.3	DisplayString	read-only	The name of the system that originated the queue entry. Corresponds directly to the value labeled 'Source Node' in the QUEUE display.
INT queueStatus	1.3.6.1.4.1.33.13.2.4.1.2	INTEGER	read-write	The status of a queue entry. Set to 'invalid' to remove the entry, which corresponds directly to the REMOVE QUEUE ENTRY command. Actual removal of the entry is implementation specific.
queueTable	1.3.6.1.4.1.33.13.2.4		not-accessible	A list of queue entries.
INT sessionLogConnectionID	1.3.6.1.4.1.33.13.6.2.1.2	INTEGER	read-only	An indentifying number for records relating to the same connection, that is, the connect and disconnect records, either of which can be missing. Corresponds directly to value labeled 'Entry' the SERVER ACCOUNTING display.
DAT sessionLogConnectTime	1.3.6.1.4.1.33.13.6.2.1.8	DateTime	read-only	The date and time that session connection occurred. Corresponds directly to the value labeled 'Connect Time' in the SERVER ACCOUNTING display.
DAT sessionLogDisconnectTime	1.3.6.1.4.1.33.13.6.2.1.9	DateTime	read-only	The date and time that session disconnection occurred. Corresponds directly to the value labeled 'Disconnect Time' in the SERVER ACCOUNTING display.
INT sessionLogEmpty	1.3.6.1.4.1.33.13.6.7	INTEGER	read-write	Control to empty the log. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes the log to be emptied.
sessionLogEntry	1.3.6.1.4.1.33.13.6.2.1		not-accessible	Parameter values for a session log entry.
INT sessionLogEvent	1.3.6.1.4.1.33.13.6.2.1.4	INTEGER	read-only	The type of event. Corresponds directly to the alphabetic part of the value labeled 'Type' in the SERVER ACCOUNTING display. Type 15 is used by internal processes that call the session log function with an already formatted message.
INT sessionLogEventDetail	1.3.6.1.4.1.33.13.6.2.1.5	INTEGER	read-only	The detailed reason for the event. Corresponds directly to the numeric part of the value labeled 'Type' in the SERVER ACCOUNTING display.
INT sessionLogFacility	1.3.6.1.4.1.33.13.6.8	INTEGER	read-write	The UNIX facility level that server originated accounting messages are logged to.
OCT sessionLogHostAddress	1.3.6.1.4.1.33.13.6.4	OCTET STRING	read-write	The address of the host to receive events.
OCT sessionLogHostSecondaryAddress	1.3.6.1.4.1.33.13.6.11	OCTET STRING	read-write	The address of a secondary host to receive events. Corresponds directly to the value labeled 'SYSLOGD Host2' in the SERVER UNIT display.
INT sessionLogHostSecondaryType	1.3.6.1.4.1.33.13.6.10	INTEGER	read-write	The type of secondary host to which session log events are to be sent. This value should be set to unix when configuring a non-zero sessionLogHostSecondaryAddress. Corresponds to the presence of the label 'SYSLOGD Host2' following the label 'Daemon(s)' in the SERVER UNIT display.
INT sessionLogHostType	1.3.6.1.4.1.33.13.6.3	INTEGER	read-write	The type of host to which session log events are to be sent.
CTR sessionLogInCharacters	1.3.6.1.4.1.33.13.6.2.1.10	Counter	read-only	The number of characters that came into the port for the session. Corresponds directly to the value labeled 'Bytes In' in the SERVER ACCOUNTING display.
INT sessionLogIndex	1.3.6.1.4.1.33.13.6.2.1.1	INTEGER	read-only	The index number of a session log entry. Corresponds directly to the order of the displayed records in the SERVER ACCOUNTING display. The maximum value is sessionLogLimit.
INT sessionLogLimit	1.3.6.1.4.1.33.13.6.1	INTEGER	read-write	The maximum number of entries allowed in the Session Log table. Corresponds directly to SERVER ACCOUNTING ENTRIES and the value labeled 'Accounting Entries:' in the SERVER CHARACTERISTICS display.
CTR sessionLogOutCharacters	1.3.6.1.4.1.33.13.6.2.1.11	Counter	read-only	The number of characters that went out of the port for the session. Corresponds directly to the value labeled 'Bytes Out' in the SERVER ACCOUNTING display.
INT sessionLogPort	1.3.6.1.4.1.33.13.6.2.1.3	INTEGER	read-only	An index value that uniquely identifies the port where the event took place. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB. Corresponds directly to the value labeled 'Port' in the SERVER ACCOUNTING display.
INT sessionLogPriority	1.3.6.1.4.1.33.13.6.6	INTEGER	read-write	The largest priority number for the system to log. Higher numbered (lower priority) events will not be logged.
INT sessionLogReliable	1.3.6.1.4.1.33.13.6.9	INTEGER	read-write	Control for reliable logging. Corresponds directly to the presence of the label 'Reliable Accounting' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display.
STR sessionLogRemoteName	1.3.6.1.4.1.33.13.6.2.1.7	DisplayString	read-only	The name of the session remote partner. Corresponds directly to the value labeled 'Destination' in the SERVER ACCOUNTING display.
sessionLogTable	1.3.6.1.4.1.33.13.6.2		not-accessible	A list of session log entries.
INT sessionLogTl1AutonomousLogSize	1.3.6.1.4.1.33.13.6.14	INTEGER	read-write	The size in bytes of the TL1 autonomous log, which records alarms. A change in log size will not take effect until rebooting the unit.
INT sessionLogTl1CommandLogSize	1.3.6.1.4.1.33.13.6.15	INTEGER	read-write	The size in bytes of the TL1 command log, which records all TL1 commands entered on this server. A change in log size will not take effect until rebooting the unit.
STR sessionLogUserName	1.3.6.1.4.1.33.13.6.2.1.6	DisplayString	read-only	The user name logged in on the port when the event occurred. Corresponds directly to the value labeled 'Username' in the SERVER ACCOUNTING display.
INT sessionLogVerbose	1.3.6.1.4.1.33.13.6.5	INTEGER	read-write	Control for verbose logging.
INT sessionLogVerboseEvent	1.3.6.1.4.1.33.13.6.2.1.12	INTEGER	read-only	When logging in 'verbose' mode, the event that occured.
STR sessionLogVerboseMessage	1.3.6.1.4.1.33.13.6.2.1.14	DisplayString	read-only	Text describing the event that was logged.
OCT sessionLogX25CalledAddress	1.3.6.1.4.1.33.13.6.2.1.16	OCTET STRING	read-only	For an X.25 connection, the X.121 destination address.
OCT sessionLogX25CallerAddress	1.3.6.1.4.1.33.13.6.2.1.15	OCTET STRING	read-only	For an X.25 connection, the X.121 source address.
INT sessionLogX25Direction	1.3.6.1.4.1.33.13.6.2.1.13	INTEGER	read-only	The initial direction for an X.25 connection. A value of 0 is returned if the session is not X25
INT sessionLogX25DisconnectCause	1.3.6.1.4.1.33.13.6.2.1.17	INTEGER	read-only	For a terminated X.25 connection, the standard, X.25 cause code.
INT sessionLogX25DisconnectDiagnostic	1.3.6.1.4.1.33.13.6.2.1.18	INTEGER	read-only	For a terminated X.25 connection, the standard, X.25 diagnostic code.
INT sessionLogZeroAccountingAll	1.3.6.1.4.1.33.13.6.12	INTEGER	read-write	A control to clear all entries in the accounting log including command log entries. Corresponds directly to the command CLEAR SERVER ACCOUNTING ALL. In response to a get-request or get-next-request the agent always returns ready for this value.
INT sessionLogZeroAlarmLogging	1.3.6.1.4.1.33.13.6.17	INTEGER	read-write	Control to clear all alarm log entries. In response to a get-request or a get-next-request the agent always returns ready for this value.
INT sessionLogZeroCommandLogging	1.3.6.1.4.1.33.13.6.13	INTEGER	read-write	A control to clear all command log entries. Corresponds directly to the command CLEAR SERVER COMMAND LOGGING. In response to a get-request or get-next-request the agent always returns ready for this value.
INT sessionLogZeroDataLogging	1.3.6.1.4.1.33.13.6.16	INTEGER	read-write	A control to clear all data log entries. Corresponds directly to the command CLEAR SERVER DATA LOGGING. In response to a get-request or get-next-request the agent always returns ready for this value.
NTF temperatureThresholdExceeded	1.3.6.1.4.1.33.0.38			Indication that the temperature exceeded a threshhold and the value of the currrent temperature.
xBasic	1.3.6.1.4.1.33.13.1
xBroadcastGroup	1.3.6.1.4.1.33.13.8
xCcl	1.3.6.1.4.1.33.13.7
xCharacter	1.3.6.1.4.1.33.13
xDial	1.3.6.1.4.1.33.13.5
xMenu	1.3.6.1.4.1.33.13.3
xNetLogin	1.3.6.1.4.1.33.13.4
xQueue	1.3.6.1.4.1.33.13.2
xSessionLog	1.3.6.1.4.1.33.13.6

OID symbolic	OID numeric	Type	Access	Description
NTF contactClosureChanged	1.3.6.1.4.1.33.0.30			Indication that the contact closure transitioned to open or closed.
NTF powerAlarmFuseBankA	1.3.6.1.4.1.33.0.31			Indicates that a fuse from bank A tripped its breaker, or that it went operational. However, it is unlikely that a trap would be issued when the fuse starts working.
NTF powerAlarmFuseBankB	1.3.6.1.4.1.33.0.32			Indicates that a fuse from bank B tripped its breaker, or that it went operational. However, it is unlikely that a trap would be issued when the fuse starts working.
NTF powerSupplyAlarmA	1.3.6.1.4.1.33.0.33			Indicates that power supply A lost or regained power. However, it is unlikely that a trap would be issued when the power comes on.
NTF powerSupplyAlarmB	1.3.6.1.4.1.33.0.34			Indicates that power supply B lost or regained power. However, it is unlikely that a trap would be issued when the power comes on.
NTF portInputSignalChange	1.3.6.1.4.1.33.0.35			Indicates that an input signal on a port has transitioned to the state indicated in the variable rs232InSigState.
NTF portOutputSignalChange	1.3.6.1.4.1.33.0.36			Indicates that an output signal on a port has transitioned to the state indicated in the variable rs232OutSigState.
NTF humidityThresholdExceeded	1.3.6.1.4.1.33.0.37			Indication that the humidity exceeded a threshhold and the value of the currrent humidity.
NTF temperatureThresholdExceeded	1.3.6.1.4.1.33.0.38			Indication that the temperature exceeded a threshhold and the value of the currrent temperature.
NTF alarmMasterNotResponding	1.3.6.1.4.1.33.0.39			Indication that the high density alarm management device lost or regained contact with the inReach port to which it was connected as indicated by the basicPortAlarmMasterStatus variable.
NTF alarmMasterInputStateChange	1.3.6.1.4.1.33.0.41			Indication that the alarm input point within a high density alarm management port transitioned to open or closed.
NTF asciiToTrapTranslation	1.3.6.1.4.1.33.0.42			This trap contains ASCII data, which arrived at serial port, was formatted as a trap, and sent out on the network.
NTF powerMasterNotResponding	1.3.6.1.4.1.33.0.43			Indication that the power management port lost or regained contact with the power unit to which it was connected as indicated by the basicPortPowerMasterDeviceStatus variable.
characterDep	1.3.6.1.4.1.33.2
xCharacter	1.3.6.1.4.1.33.13
xBasic	1.3.6.1.4.1.33.13.1
INT basicBroadcast	1.3.6.1.4.1.33.13.1.1	INTEGER	read-write	Control for user ability to broadcast messages to other local ports. Corresponds directly to SERVER BROADCAST and the presence of the label 'Broadcast' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display.
INT basicErrorReport	1.3.6.1.4.1.33.13.1.2	INTEGER	read-write	Control for server display of an error when the user gives an unsupported command. Corresponds directly to SERVER REPORT ERRORS and the presence of the label 'Report Errors' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display.
INT basicLock	1.3.6.1.4.1.33.13.1.3	INTEGER	read-write	Control for user ability to use a password to protect a logged in terminal from other users. Corresponds directly to SERVER LOCK and the presence of the label 'Lock' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display.
INT basicInactivityTimer	1.3.6.1.4.1.33.13.1.4	INTEGER	read-write	Number of minutes a terminal may remain logged in with no sessions, no input or output, and no modem transitions. Corresponds directly to SERVER INACTIVITY TIMER and the value labeled 'Inactivity Timer:' in the SERVER CHARACTERISTICS display.
INT basicPasswordRetryLimit	1.3.6.1.4.1.33.13.1.5	INTEGER	read-write	Number of times the server allows a user to retry an incorrect password. Corresponds directly to SERVER PASSWORD LIMIT and the value labeled 'Password Limit:' in the SERVER CHARACTERISTICS display.
STR basicPrivilegedPassword	1.3.6.1.4.1.33.13.1.6	DisplayString	read-write	The password a user must enter to become privileged. For security reasons, reading this object always returns a zero-length value. Corresponds directly to SERVER PRIVILEGED PASSWORD.
STR basicLoginPassword	1.3.6.1.4.1.33.13.1.7	DisplayString	read-write	The password a user must enter to be given the opportunity to log in. For security reasons, reading this object always returns a zero-length value. Corresponds directly to SERVER LOGIN PASSWORD.
STR basicLoginPrompt	1.3.6.1.4.1.33.13.1.8	DisplayString	read-write	The text string the server displays to prompt a user for the login password. Corresponds directly to SERVER LOGIN PROMPT.
STR basicWelcome	1.3.6.1.4.1.33.13.1.9	DisplayString	read-write	The text string the server displays before attempting to log in a user. Corresponds directly to SERVER WELCOME and the value labeled 'Welcome:' in the SERVER CHARACTERISTICS display.
GAU basicActivePorts	1.3.6.1.4.1.33.13.1.10	Gauge	read-only	The number of ports with connected sessions or logged in users. Corresponds directly to the value labeled 'Active Ports:' and 'Cur' in the SERVER STATUS display.
GAU basicActivePortsHigh	1.3.6.1.4.1.33.13.1.11	Gauge	read-only	The highest value of basicActivePorts since system initialization. Corresponds directly to the value labeled 'Active Ports:' and 'High' in the SERVER STATUS display.
GAU basicActiveUsers	1.3.6.1.4.1.33.13.1.12	Gauge	read-only	The number of logged in users. Corresponds directly to the value labeled 'Active Users:' and 'Cur' in the SERVER STATUS display.
GAU basicActiveUsersHigh	1.3.6.1.4.1.33.13.1.13	Gauge	read-only	The highest value of basicActiveUsers since system initialization. Corresponds directly to the value labeled 'Active Users:' and 'High' in the SERVER STATUS display.
GAU basicSessions	1.3.6.1.4.1.33.13.1.14	Gauge	read-only	The total number of connected sessions. Corresponds directly to the value labeled 'Connected Sessions:' and 'Cur' in the SERVER STATUS display.
GAU basicSessionsHigh	1.3.6.1.4.1.33.13.1.15	Gauge	read-only	The highest value of basicSessions since system initialization. Corresponds directly to the value labeled 'Connected Sessions:' and 'High' in the SERVER STATUS display.
INT basicSessionsLimit	1.3.6.1.4.1.33.13.1.16	INTEGER	read-write	The maximum total number of sessions that can simultaneously be connected to the system. A value of -1 indicates no limit up to available dynamic system memory. Corresponds directly to SERVER SESSION LIMIT and the value labeled 'Connected Sessions:' and 'Max' in the SERVER STATUS display.
basicPortTable	1.3.6.1.4.1.33.13.1.17		not-accessible	A list of basic character port entries.
basicPortEntry	1.3.6.1.4.1.33.13.1.17.1		not-accessible	Basic parameter values for a port.
INT basicPortIndex	1.3.6.1.4.1.33.13.1.17.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT basicPortDefaultDestAction	1.3.6.1.4.1.33.13.1.17.1.2	INTEGER	read-write	The action to take relative to basicPortDefaultDestName. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE and the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display.
INT basicPortDefaultDestProtocol	1.3.6.1.4.1.33.13.1.17.1.3	INTEGER	read-write	The session protocol to use with basicPortDefaultDestName. Corresponds directly to LAT/TELNET PORT DEDICATED/PREFERRED SERVICE.
STR basicPortDefaultDestName	1.3.6.1.4.1.33.13.1.17.1.4	DisplayString	read-write	The default name to use in forming a connection when no other name is specified. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE and the value labeled 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. If the value of basicPortDefaultDestProtocol is 'telnet', an Internet port number may be included on the end of the name, delimited with a colon (':'). If the value of basicPortDefaultDestProtocol is not 'telnet', then the maximum length is 16.
STR basicPortDefaultDestLATNodeName	1.3.6.1.4.1.33.13.1.17.1.5	DisplayString	read-write	A LAT node name to use with basicPortDefaultDestName. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE NODE and the value labeled 'Node:' following the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. This object can have a non- zero-length value only if the value of basicPortDefaultDestProtocol is 'lat'.
STR basicPortDefaultDestLATPortName	1.3.6.1.4.1.33.13.1.17.1.6	DisplayString	read-write	A LAT port name to use with basicPortDefaultDestName. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE NODE and the value labeled 'Node:' following the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. this object can hav a non-zero-length value only if the value if basicPortDefaultDestProtocol is 'lat'
INT basicPortAutoConnect	1.3.6.1.4.1.33.13.1.17.1.7	INTEGER	read-write	Control for automatic session connection. Corresponds directly to PORT AUTOCONNECT and the presence of the label 'Autoconnect' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortAutoLogin	1.3.6.1.4.1.33.13.1.17.1.8	INTEGER	read-write	Control for automatic port login. Corresponds directly to PORT AUTODEDICATED and the presence of the label 'Autodedicated' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortBroadcast	1.3.6.1.4.1.33.13.1.17.1.9	INTEGER	read-write	Control for display of messages sent by users on other ports. Corresponds directly to PORT BROADCAST and the presence of the label 'Broadcast' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortConnectResume	1.3.6.1.4.1.33.13.1.17.1.10	INTEGER	read-write	Control for behavior of a connection attempt to a destination where the port already has a connection. 'disabled' causes a new connection. 'enabled' causes the existing connection to become the active connection. Corresponds directly to PORT CONNECTRESUME and the presence of the label 'Connectresume' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortDialup	1.3.6.1.4.1.33.13.1.17.1.11	INTEGER	read-write	Defines whether the port should be considered as connected to a dialup line. 'enabled' means that it is. Corresponds directly to PORT DIALUP and the presence of the label 'Dial Up' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicPortIdleTimeout	1.3.6.1.4.1.33.13.1.17.1.12	INTEGER	read-write	The number of minutes the system will allow a session to have no activity before automatically disconnecting it. A value of -1 indicates no timeout. Zero is not a valid value. Corresponds directly to PORT IDLE TIMEOUT and the value labeled 'Idle Timeout:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicPortInactivityLogout	1.3.6.1.4.1.33.13.1.17.1.13	INTEGER	read-write	Control for the system automatically logging the port out when it has no sessions, no local activity, and no modem signal changes for the time period specified by basicInactivityTimer. Corresponds directly to PORT INACTIVITY LOGOUT and the presence of the label 'Inactivity Logout' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortLossNotification	1.3.6.1.4.1.33.13.1.17.1.14	INTEGER	read-write	Control for the system sending a Bell character to the port when it looses an input character due to an overrun or data error. Corresponds directly to PORT LOSS NOTIFICATION and the presence of the label 'Loss Notification' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortMessageCodes	1.3.6.1.4.1.33.13.1.17.1.15	INTEGER	read-write	Control for including error numbers in error messages displayed on the port. Corresponds directly to PORT MESSAGE CODES and the presence of the label 'Message Codes' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortMultisessions	1.3.6.1.4.1.33.13.1.17.1.16	INTEGER	read-write	Control for running the multisession line protocol between the port and the locally-connected terminal. Corresponds directly to PORT MULTISESSIONS and the presence of the label 'Multisessions' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
STR basicPortDefaultUserName	1.3.6.1.4.1.33.13.1.17.1.17	DisplayString	read-write	Default user name to use for automatically logging in the port. Corresponds directly to PORT USERNAME and the value labeled 'Port n:' in the PORT CHARACTERISTICS display.
INT basicPortVerification	1.3.6.1.4.1.33.13.1.17.1.18	INTEGER	read-write	Control for display of informational messages on the port when the user connects, disconnects, or switches a session. Corresponds directly to PORT VERIFICATION and the presence of the label 'Verification' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortDefaultProtocol	1.3.6.1.4.1.33.13.1.17.1.19	INTEGER	read-write	The session protocol to use when not otherwise specified. Corresponds directly to PORT RESOLVE SERVICE and the value labeled 'Resolve Service:' in the PORT ALTERNATE CHARACTERISTICS display.
CTR basicPortLogins	1.3.6.1.4.1.33.13.1.17.1.20	Counter	read-only	The number of logins on the port since system initialization. Corresponds directly to the value labeled 'Local Accesses:' in the PORT COUNTERS display.
CTR basicPortRemoteSessions	1.3.6.1.4.1.33.13.1.17.1.21	Counter	read-only	The number of remotely originating sessions to the port since system initialization. Corresponds directly to the value labeled 'Remote Accesses:' in the PORT COUNTERS display.
CTR basicPortIdleTimeouts	1.3.6.1.4.1.33.13.1.17.1.22	Counter	read-only	The number of session disconnects due to expiration of basicPortIdleTimeout. Corresponds directly to the value labeled 'Idle Timeouts:' in the PORT COUNTERS display.
INT basicPortStatus	1.3.6.1.4.1.33.13.1.17.1.23	INTEGER	read-only	The current operational status of the port. Corresponds directly to the value labeled 'Status:' in the PORT STATUS display.
INT basicPortLastInCharacter	1.3.6.1.4.1.33.13.1.17.1.24	INTEGER	read-only	The character that most recently came into the port. Corresponds directly to the value labeled 'Last Char Input:' in the PORT STATUS display.
INT basicPortLastOutCharacter	1.3.6.1.4.1.33.13.1.17.1.25	INTEGER	read-only	The character that most recently went out of the port. Corresponds directly to the value labeled 'Last Char Output:' in the PORT STATUS display.
STR basicPortActiveUserName	1.3.6.1.4.1.33.13.1.17.1.26	DisplayString	read-only	The user name currently logged into the port. Corresponds directly to the value by the port number and labeled 'Username' in the USERS display.
INT basicPortDefaultSessionMode	1.3.6.1.4.1.33.13.1.17.1.27	INTEGER	read-write	Data recognition mode when starting a session, with the following meanings: interactive locally recognize all controls binary recognize only session protocol (corresponds to PASSALL) binaryWithFlow recognize only XON and XOFF (corresponds to PASTHRU transparent recognize no data Corresponds directly to PORT DEFAULT SESSION MODE and the value labeled 'Default Session Mode:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicPortZero	1.3.6.1.4.1.33.13.1.17.1.28	INTEGER	read-write	Control to zero counters for the port. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes the port's counters to be zeroed. Corresponds to the ZERO PORT command.
TIK basicPortZeroTime	1.3.6.1.4.1.33.13.1.17.1.29	TimeTicks	read-only	The number of hundredths of a second since the most recent zeroing of the port's counters, such as through execution of basicPortZero. Corresponds directly to the value labeled 'Seconds Since Zeroed:' in the PORT COUNTERS display.
INT basicPortUnixCommands	1.3.6.1.4.1.33.13.1.17.1.30	INTEGER	read-write	Control to allow the user to use Unix-style commands the port.
INT basicPortSessionMode	1.3.6.1.4.1.33.13.1.17.1.31	INTEGER	read-write	Data recognition mode for an active session, with the following meanings: interactive locally recognize all controls binary recognize only session protocol (corresponds to PASSALL) binaryWithFlow recognize only XON and XOFF (corresponds to PASTHRU transparent recognize no data noActiveSessions no sessions on this port. This object can be set to values of 1 to 4, but only if there is an active session on the port.
INT basicPortRemoteDisconnectNotify	1.3.6.1.4.1.33.13.1.17.1.32	INTEGER	read-write	If enabled, a BELL (ctrl G) will be sent out the serial port when a remote session is disconnected and the port is logged out.
INT basicPortDefaultDestControlled	1.3.6.1.4.1.33.13.1.17.1.33	INTEGER	read-write	A control to send preconfigured controlled port session strings when entering or exiting a session established to the basicPortDefaultDestName. Corresponds directly to the value labeled '(Controlled)' following the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display.
OCT basicPortControlledPortLogin	1.3.6.1.4.1.33.13.1.17.1.34	OCTET STRING	read-write	A control string to send out the serial port upon port login. Corresponds to the hexadecimal code which is represented in ASCII following the label 'Controlled Port Login:' in the PORT CONTROLLED display.
OCT basicPortControlledPortLogout	1.3.6.1.4.1.33.13.1.17.1.35	OCTET STRING	read-write	A control string to send out the serial port upon port logout. Corresponds to the hexadecimal code which is represented in ASCII following the label 'Controlled Port Logout:' in the PORT CONTROLLED display.
OCT basicPortControlledSessionInitialize	1.3.6.1.4.1.33.13.1.17.1.36	OCTET STRING	read-write	A control string to send out the serial port upon entering a session. Corresponds to the hexadecimal code which represented in ASCII following the label 'Controlled Session Initialize:' in the PORT CONTROLLED display.
OCT basicPortControlledSessionTerminate	1.3.6.1.4.1.33.13.1.17.1.37	OCTET STRING	read-write	A control string to send out the serial port upon exiting a session. Corresponds to the hexadecimal code which is represented in ASCII following the label 'Controlled Session Terminate:' in the PORT CONTROLLED display.
INT basicPortRloginTransparentMode	1.3.6.1.4.1.33.13.1.17.1.38	INTEGER	read-write	A control to pass x'ff' as binary data, not doubling x'ff'. Similar to basicPortSessionMode = transparent but for a rlogin session.
INT basicPortLoginDuration	1.3.6.1.4.1.33.13.1.17.1.39	INTEGER	read-write	The amount of time in minutes that a port may remain logged in regardless of the activity on the port. The value 0 indicates that the timer is disabled. Corresponds directly to the value labeled 'Login Duration:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicPortOutboundSecurity	1.3.6.1.4.1.33.13.1.17.1.40	INTEGER	read-write	Control to disable outbound security, which can be either Kerberos or SecureID, on a per port basis. Corresponds directly to the presence of the value 'OutboundSecurity' following the label 'Enabled Characteristics' in the PORT CHARACTERISTICS display.
INT basicPortXonTimer	1.3.6.1.4.1.33.13.1.17.1.41	INTEGER	read-write	Indicates the number of seconds between successive 'XON's sent out a port. A zero signifies that the timer is disabled. Corresponds directly to the value labeled 'Xon Send Timer:' in the PORT ALTERNATE CHARACTERISTICS display.
OCT basicPortDefaultDedicatedSessionType	1.3.6.1.4.1.33.13.1.17.1.42	OCTET STRING	read-write	A bit mask that specifies the default session type for a dedicated service for this port. The bit numbers are: 1;service name, 2;node name, 3;port name, 4, telnet console; 5, rlogin; 6, bridge console; 7, chassis console.
INT basicPortIdleTimeReceive	1.3.6.1.4.1.33.13.1.17.1.43	INTEGER	read-write	Control to restrict the basicPortIdleTimeout to apply to data received from the network and transmitted out the serial port. Data received by the serial port will not be considered activity. Corresponds directly to the value labeled 'Idle Time Receive Mode:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicPortIdleTimeTransmit	1.3.6.1.4.1.33.13.1.17.1.44	INTEGER	read-write	Control to restrict the basicPortIdleTimeout to apply to data received from the serial port and transmitted out the LAN. Data received from the network will not count as activity. Corresponds directly to the value labeled 'Idle Time Transmit Mode:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicPortZeroDisconnectSession	1.3.6.1.4.1.33.13.1.17.1.45	INTEGER	read-write	A control to disconnect a session at Port 0 when the password limit is reached.
INT basicPortConsolePort	1.3.6.1.4.1.33.13.1.17.1.46	INTEGER	read-write	Control to configure this port as a console port. This control is only valid on those models with variable configuration ports. This object can only be set enabled; and doing so will disable basicPortSensor and basicPortAlarmControl. A set will only update the permanent database. Use a charPortReset for this change to take effect.
STR basicPortLoginPassword	1.3.6.1.4.1.33.13.1.17.1.47	DisplayString	read-write	The password a user must enter to be given the opportunity to log in to a given port. For security reasons reading this object always returns a zero-length value. Corresponds directly to PORT LOGIN PASSWORD.
INT basicPortSensor	1.3.6.1.4.1.33.13.1.17.1.48	INTEGER	read-write	Control to configure this port as a temperature and humidity sensor. This control is only valid on those models with variable configuration ports. This object can only be set enabled; and doing so will disable basicPortConsolePort and basicPortAlarmControl. A set will only update the permanent database. Use a charPortReset for this change to take effect.
INT basicPortAlarmControl	1.3.6.1.4.1.33.13.1.17.1.49	INTEGER	read-write	Control to configure this port for alarm input and control output. This control is only valid on those models with variable configuration ports. This object can only be set enabled; and doing so will disable basicPortConsolePort and basicPortSensor. A set will only update the permanent database. Use a charPortReset for this change to take effect.
INT basicPortCommandLogging	1.3.6.1.4.1.33.13.1.17.1.50	INTEGER	read-write	A control to toggle logging of commands at this port. Command input may be logged from direct terminal connections, session input from the LAN, or session output to the LAN. Corresponds directly to the presence of 'Command Logging' under the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. The desired change will not take effect until the port is logged off.
OCT basicPortBreakSequence	1.3.6.1.4.1.33.13.1.17.1.51	OCTET STRING	read-write	A sequence of characters to be sent out the serial port on receipt of a Break from the network in lieu of a hardware break.
INT basicPortTl1Mode	1.3.6.1.4.1.33.13.1.17.1.53	INTEGER	read-write	Controls the TL1 mode of a port. Valid TL1 modes are human- to-machine language (hml), machine-to-machine language (mml), and MML without echo. MML is for direct connection to another TL1 device whereas HML provides human prompts. A change takes effect after logging out the port.
INT basicPortTl1Console	1.3.6.1.4.1.33.13.1.17.1.54	INTEGER	read-write	Controls whether this port becomes the TL1 console receiving and displaying autonomous reports of alarm events. A change takes effect after logging out the port.
INT basicPortFallThrough	1.3.6.1.4.1.33.13.1.17.1.55	INTEGER	read-write	Control to allow a user to login to a port after RADIUS or SecurID authentication fails because the RADIUS servers or SecurID servers are unavailable. When a user is logged in via 'fallthrough', he is logged in to the port as a non-privileged user. The change takes effect after logging out the port.
INT basicPortCommandLoggingSuppressControlCharacters	1.3.6.1.4.1.33.13.1.17.1.56	INTEGER	read-write	Control to toggle suppression of control characters in the command log. This object can only be set to enabled when command logging is enabled on that port.
INT basicPortDataLogging	1.3.6.1.4.1.33.13.1.17.1.57	INTEGER	read-write	Control to toggle data logging on the specified port.
INT basicPortDataLoggingSuppressControlCharacters	1.3.6.1.4.1.33.13.1.17.1.58	INTEGER	read-write	Control to toggle suppression of control characters in the data log. This object can only be set to enabled when data logging is enabled on that port.
INT basicPortOnboardSecurity	1.3.6.1.4.1.33.13.1.17.1.59	INTEGER	read-write	A control to toggle onboard security for this port where the username and password are authenticated against an internal access list. The desired change will not take effect until the port is logged off.
INT basicPortFallBack	1.3.6.1.4.1.33.13.1.17.1.60	INTEGER	read-write	Control to allow a 'fallback' authentication mechanism after RADIUS or SecurID authentication fails because the RADIUS or SecurID servers are unavailable. Onboard security, an internal security database, is used for fallback authentication. The user in fallback mode must enter a valid username and password to be successfully logged in. The change takes effect after logging out the port.
INT basicPortAlarmMaster	1.3.6.1.4.1.33.13.1.17.1.61	INTEGER	read-write	Control to configure this port for high densitiy alarm input and control output management. This control is only valid on those models with variable configuration ports. This object can only be set enabled; and doing so will disable basicPortConsolePort, basicPortSensor and basicPortAlarmControl. A set will only update the permanent database. Use a charPortReset for this change to take effect.
INT basicPortAlarmMasterAccounting	1.3.6.1.4.1.33.13.1.17.1.62	INTEGER	read-write	Control to toggle logging of alarm events on this port. Use a charPortReset for this change to take effect.
INT basicPortAlarmMasterAudibleAlarm	1.3.6.1.4.1.33.13.1.17.1.63	INTEGER	read-write	Control whether the alarm will have an audible sound for all alarm points attached to this port.
INT basicPortAlarmMasterFixTime	1.3.6.1.4.1.33.13.1.17.1.64	INTEGER	read-write	Time in minutes between audible alarm soundings for an alarm master port. This occurs after someone hits the master alarm reset button. If there is at least one alarm condition on an alarm point within the fix time, then the alarm will sound again at the end of that fix time.
STR basicPortAlarmMasterLcdDisplayString	1.3.6.1.4.1.33.13.1.17.1.65	DisplayString	read-write	Updates the LCD display message for the high density alarm unit attached to the port. Corresponds directly to the DISPLAY AMST command.
INT basicPortAlarmMasterReboot	1.3.6.1.4.1.33.13.1.17.1.66	INTEGER	read-write	Control to reboot the high density alarm unit attached to the port when set to 'execute'. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Corresponds directly to the REBOOT AMST command.
IP basicPortAlarmMasterUpdateFirmwareHost	1.3.6.1.4.1.33.13.1.17.1.67	IpAddress	read-write	The internet address of the server to use when downloading a new firmware image for the high density alarm unit attached to this port via TFTP. Corresponds directly to the UPDATE AMST FIRMWARE command's INTERNET ADDRESS parameter.
STR basicPortAlarmMasterUpdateFirmwareFileName	1.3.6.1.4.1.33.13.1.17.1.68	DisplayString	read-write	The filename to request when downloading a new firmware image for the high density alarm unit attached to this port via TFTP. Corresponds directly to the UPDATE AMST FIRMWARE command's FILE parameter.
INT basicPortAlarmMasterUpdateFirmware	1.3.6.1.4.1.33.13.1.17.1.69	INTEGER	read-write	Control to update firmware for the high density alarm unit attached to the port when set to 'execute'. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. The basicPortAlarmMasterUpdateFirmwareHost and basicPortAlarmMasterUpdateFirmwareFileName must be set prior to setting this object. Corresponds directly to the UPDATE AMST FIRMWARE command.
INT basicPortAlarmMasterStatus	1.3.6.1.4.1.33.13.1.17.1.70	INTEGER	read-only	Indicates the current status of the high density alarm unit attached to the port. If no response is obtained from this unit, the status is set to basicPortAlarmMasterFaultSeverity. Otherwise it is cleared.
INT basicPortAlarmMasterFaultSeverity	1.3.6.1.4.1.33.13.1.17.1.71	INTEGER	read-write	Control to determine the severity level associated with the trap sent out when a fault occurs when no response is obtained from the high density alarm unit attached to this port.
INT basicPortPowerMaster	1.3.6.1.4.1.33.13.1.17.1.72	INTEGER	read-write	Control to configure this port as a power master port. This control is only valid on those models with variable configuration ports and which support the power master. This object can only be set enabled, and doing so will disable the previous port type, such as basicPortConsolePort. A set will only update the permanent database. Use a charPortReset for this change to take effect.
INT basicPortPowerMasterTimeDelay	1.3.6.1.4.1.33.13.1.17.1.73	INTEGER	read-write	Control to set the power up delay interval in milliseconds for the power device attached to this port.
INT basicPortPowerMasterSwitch	1.3.6.1.4.1.33.13.1.17.1.74	INTEGER	read-write	Control to power on or off all of the outlets in the power device attached to this port. A get-request always returns ready.
STR basicPortPowerMasterModel	1.3.6.1.4.1.33.13.1.17.1.75	DisplayString	read-only	The model number of the power master device, which is connected to this port.
STR basicPortPowerMasterSerialNumber	1.3.6.1.4.1.33.13.1.17.1.76	DisplayString	read-only	The serial number of the power master device, which is connected to this port.
STR basicPortPowerMasterFirmware	1.3.6.1.4.1.33.13.1.17.1.77	DisplayString	read-only	The firmware version of the power master device, which is connected to this port.
INT basicPortLockout	1.3.6.1.4.1.33.13.1.17.1.78	INTEGER	read-write	Control to prohibit access to this port and send a trap when login authentication fails. One must log out the port for this change to take effect.
INT basicPortAsciiToTrapTranslation	1.3.6.1.4.1.33.13.1.17.1.79	INTEGER	read-write	Control to configure the port as an ascii-to-trap translator. One must log out the port for this change to take effect.
INT basicPortAsciiToTrapTranslationTrapSeverity	1.3.6.1.4.1.33.13.1.17.1.80	INTEGER	read-write	Control to determine the severity level associated with the trap sent out from this port. One must log out the port for this change to take effect.
CTR basicPortAsciiToTrapTranslationMessages	1.3.6.1.4.1.33.13.1.17.1.81	Counter	read-only	Count of number of trap messages sent from this port.
STR basicPortAsciiToTrapTranslationLastMessage	1.3.6.1.4.1.33.13.1.17.1.82	DisplayString	read-only	The last message or partial message sent out by this port.
INT basicPortPowerMasterAlarmSeverity	1.3.6.1.4.1.33.13.1.17.1.83	INTEGER	read-write	Control to determine the severity level associated with the trap sent out when the power device is not responding to this port.
INT basicPortPowerMasterDeviceStatus	1.3.6.1.4.1.33.13.1.17.1.84	INTEGER	read-only	Indicates the current status of the power device controlled by this port. If the device is responding, the status is cleared. Otherwise the status matches the basicPortPowerMasterAlarmSeverity.
basicSerialPortTable	1.3.6.1.4.1.33.13.1.18		not-accessible	A list of basic character serial port entries.
basicSerialPortEntry	1.3.6.1.4.1.33.13.1.18.1		not-accessible	Basic parameter values for a serial port.
INT basicSerialPortIndex	1.3.6.1.4.1.33.13.1.18.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT basicSerialPortBreak	1.3.6.1.4.1.33.13.1.18.1.2	INTEGER	read-write	Action to take on a BREAK condition from the port. Corresponds directly to PORT BREAK and the value labeled 'Break:' in the PORT CHARACTERISTICS display.
INT basicSerialPortInterrupts	1.3.6.1.4.1.33.13.1.18.1.3	INTEGER	read-write	Control for recognizing BREAK or local switch to interrupt a session. Corresponds directly to PORT INTERRUPTS and the presence of the label 'Interrupts' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicSerialPortNoLoss	1.3.6.1.4.1.33.13.1.18.1.4	INTEGER	read-write	Control for storing port input locally in anticipation of session startup. Corresponds directly to PORT NOLOSS and the presence of the label 'Noloss' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicSerialPortPause	1.3.6.1.4.1.33.13.1.18.1.5	INTEGER	read-write	Control for pausing after each screenful of locally-originated output to the port. Corresponds directly to PORT PAUSE and the presence of the label 'Pause' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
STR basicSerialPortPrompt	1.3.6.1.4.1.33.13.1.18.1.6	DisplayString	read-write	Prompt for the system to use on the port. Corresponds directly to PORT PROMPT and the value labeled 'Prompt:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortTerminalType	1.3.6.1.4.1.33.13.1.18.1.7	INTEGER	read-write	Type of terminal attached to the port, for formatting local output. Corresponds directly to PORT TYPE and the value labeled 'Type:' in the PORT CHARACTERISTICS display.
INT basicSerialPortTypeaheadLimit	1.3.6.1.4.1.33.13.1.18.1.8	INTEGER	read-write	Maximum number of input characters to hold pending tranmission on a session. Corresponds directly to PORT TYPEAHEAD SIZE and the value labeled 'Typeahead Size:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortBackwardSwitch	1.3.6.1.4.1.33.13.1.18.1.9	INTEGER	read-write	Character input from the character port to cause a switch to the previous, lower numbered session. The value 0 indicates no character has this effect. Corresponds directly to PORT BACKWARD SWITCH and the value labeled 'Backwards Switch:' in the PORT CHARACTERISTICS display.
INT basicSerialPortForwardSwitch	1.3.6.1.4.1.33.13.1.18.1.10	INTEGER	read-write	Character input from the character port to cause a switch to the next, higher numbered session. The value 0 indicates no character has this effect. Corresponds directly to PORT FORWARD SWITCH and the value labeled 'Forwards Switch:' in the PORT CHARACTERISTICS display.
INT basicSerialPortLocalSwitch	1.3.6.1.4.1.33.13.1.18.1.11	INTEGER	read-write	Character input from the character port to cause a switch to local command mode. The value 0 indicates no character has this effect. Corresponds directly to PORT LOCAL SWITCH and the value labeled 'Local Switch:' in the PORT CHARACTERISTICS display.
INT basicSerialPortModemControl	1.3.6.1.4.1.33.13.1.18.1.12	INTEGER	read-write	Control for observing hardware modem control signals. Corresponds directly to PORT MODEM CONTROL and the value labeled 'Modem Control:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortSignalCheck	1.3.6.1.4.1.33.13.1.18.1.13	INTEGER	read-write	Control for observing DSR and DCD to bound allowing sessions. Corresponds directly to PORT SIGNAL CHECK and the presence of the label 'Signal Check' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortDSRLogout	1.3.6.1.4.1.33.13.1.18.1.14	INTEGER	read-write	Control for logging out the port when DCD is deasserted. Corresponds directly to PORT DSRLOGOUT and the presence of the label 'DSRlogout' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortDSRObserve	1.3.6.1.4.1.33.13.1.18.1.15	INTEGER	read-write	Control for beginning the login sequence on the port when DCD is asserted. Corresponds directly to PORT DSRWAIT and the presence of the label 'DSRwait' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortDCDTimeout	1.3.6.1.4.1.33.13.1.18.1.16	INTEGER	read-write	The number of milleseconds that DCD may be asserted before disconnecting the port. Corresponds directly to PORT DCD TIMEOUT and the value labeled 'DCD Timeout:' in the PORT ALTERNATE CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortDTRAssert	1.3.6.1.4.1.33.13.1.18.1.17	INTEGER	read-write	Control when the system asserts DTR on the port. always unconditional(DISABLED) onConnectionOrRing connection formed or RING asserted(ENABLED) onConnection connection formed (FORCONNECTION) onRing RING asserted (FORRING) Corresponds directly to PORT DTRWAIT and the value labeled 'DTR Wait:' in the PORT ALTERNATE CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortLimitedCommands	1.3.6.1.4.1.33.13.1.18.1.18	INTEGER	read-write	Control for limiting the commands available to the user on the port. Corresponds directly to PORT SECURITY and the presence of the label 'Security' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortLimitedView	1.3.6.1.4.1.33.13.1.18.1.19	INTEGER	read-write	Control for restricting what a user may display. Corresponds directly to PORT LIMITED VIEW and the presence of the label 'Limited View' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicSerialPortPassword	1.3.6.1.4.1.33.13.1.18.1.20	INTEGER	read-write	Control for requiring the user to supply the login password to log in on the port. Corresponds directly to PORT PASSWORD and the presence of the label 'Password' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicSerialPortLineEditor	1.3.6.1.4.1.33.13.1.18.1.21	INTEGER	read-write	Control for allowing the user to use local mode command line editing. Corresponds directly to PORT LINE EDITOR and the presence of the label 'Line Editor' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicSerialPortLineEditorBackspace	1.3.6.1.4.1.33.13.1.18.1.22	INTEGER	read-write	Character input from the character port to move the cursor to the left. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR BACKSPACE and the value labeled 'Backspace Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorBeginning	1.3.6.1.4.1.33.13.1.18.1.23	INTEGER	read-write	Character input from the character port to move the cursor to the beginning of the line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR BEGINNING and the value labeled 'Begin Line Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorCancel	1.3.6.1.4.1.33.13.1.18.1.24	INTEGER	read-write	Character input from the character port to cancel an interactive dialog or delete the current line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR CANCEL and the value labeled 'Cancel Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorDeleteBeginning	1.3.6.1.4.1.33.13.1.18.1.25	INTEGER	read-write	Character input from the character port to delete the current line from the cursor to the beginning. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR DELETE BEGINNING and the value labeled 'Delete Begin Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorDeleteLine	1.3.6.1.4.1.33.13.1.18.1.26	INTEGER	read-write	Character input from the character port to delete the current line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR DELETE LINE and the value labeled 'Delete Line Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorEnd	1.3.6.1.4.1.33.13.1.18.1.27	INTEGER	read-write	Character input from the character port to move the cursor to the end of the line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR END and the value labeled 'End of Line Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorForward	1.3.6.1.4.1.33.13.1.18.1.28	INTEGER	read-write	Character input from the character port to move the cursor to the right. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR FORWARDS and the value labeled 'Forwards Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorInsertToggle	1.3.6.1.4.1.33.13.1.18.1.29	INTEGER	read-write	Character input from the character port to toggle between insert and overwrite modes. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR INSERT TOGGLE and the value labeled 'Insert Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorNextLine	1.3.6.1.4.1.33.13.1.18.1.30	INTEGER	read-write	Character input from the character port to recall the next, newer line in the command history. The value -1 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR NEXT LINE and the value labeled 'Next Line Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorPreviousLine	1.3.6.1.4.1.33.13.1.18.1.31	INTEGER	read-write	Character input from the character port to recall the previous, older line in the command history. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR PREVIOUS LINE and the value labeled 'Previous Line Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorQuotingCharacter	1.3.6.1.4.1.33.13.1.18.1.32	INTEGER	read-write	Character input from the character port to inhibit interpretation of the next input character. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR QUOTING CHARACTER and the value labeled 'Quoting Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorRedisplay	1.3.6.1.4.1.33.13.1.18.1.33	INTEGER	read-write	Character input from the character port to redisplay the current command line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR REDISPLAY CHARACTER and the value labeled 'Redisplay Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortQuadartReceiveDiscard	1.3.6.1.4.1.33.13.1.18.1.34	INTEGER	read-write	Control for discard of received errors from quadart hardware.
OCT basicSerialPortAPDProtocols	1.3.6.1.4.1.33.13.1.18.1.35	OCTET STRING	read-write	A bit map that specifies the protocols that this port will attempt to detect using the Auto Protocol Detection function. The bit numbers for the protocols are: 1;ARAP, 3;Interactive, 4;SLIP, 5;PPP. Bits 6-16 are reserved for future use. More than one of these protocols may be ORed together. The default is 0 (zero) no protocols.
INT basicSerialPortAPDTimeout	1.3.6.1.4.1.33.13.1.18.1.36	INTEGER	read-write	A time value, in seconds, that specifies how long the port will attempt to determine which protocol is coming into the port. When basicSerialPortAPDTimeout seconds have expired, the port will assume the protocol to use is that specified by basicSerialPortAPDDefaultProtocol. A value of 0 (zero provides an unlimited timeout.
OCT basicSerialPortAPDDefaultProtocol	1.3.6.1.4.1.33.13.1.18.1.37	OCTET STRING	read-write	A bit map that specifies the protocol that this port will use when the time specified by basicSerialPortAPDTimeout has expired without sucessfully identifying the incoming porotocol. The bit numbers for the protocols are: None;Logout the port, 1;ARAP, 2;CSLIP, 3;Interactive, 4;SLIP, 5;PPP. Bits 6-16 are reserved for future use. Only one protocol may be specified for this object
INT basicSerialPortUsernameCharSet	1.3.6.1.4.1.33.13.1.18.1.38	INTEGER	read-write	A control, that if set to seven-bit, will allow only the ASCII printable characters in the range SP (X20) to ~ (X7E) in the username field. A value of none allows any character
INT basicSerialPortAutoHangup	1.3.6.1.4.1.33.13.1.18.1.39	INTEGER	read-write	A control that, if enabled, will cause the port to be logged off when the last session on that port is destroyed
INT basicSerialPortCommandSize	1.3.6.1.4.1.33.13.1.18.1.40	INTEGER	read-write	Maximum number of input characters to hold in the command buffer. Corresponds directly to the PORT COMMAND SIZE and the value labeled 'Command Size:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortAutoProtocolDetectPrompt	1.3.6.1.4.1.33.13.1.18.1.41	INTEGER	read-write	Controls whether to send the basicAutoProtocolDetectMessage out the serial port at the beginning of auto protocol detection mode. Corresponds to the value labeled 'APD Prompt' in the PORT ALTERNATE CHARACTERISTICS display.
STR basicSerialPortUsernamePrompt	1.3.6.1.4.1.33.13.1.18.1.42	DisplayString	read-write	The text string used to prompt for a user's name. Corresponds directly to the value labeled 'Username Prompt:' in the PORT ALTERNATE CHARACTERISTICS display.
STR basicSerialPortPasswordPrompt	1.3.6.1.4.1.33.13.1.18.1.43	DisplayString	read-write	The text string used to prompt for a user's password. Corresponds directly to the value labeled 'Password Prompt:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortAutoProtocolDetectSecurityInteractiveOnly	1.3.6.1.4.1.33.13.1.18.1.44	INTEGER	read-write	Controls whether Auto Protocol Detect (APD) authentication applies only to interactive users, and not to other APD protocols such as PPP. Corresponds directly to the value labeled 'APD Authentication Interactive Only:' in the PORT CHARACTERISTICS display.
STR basicSerialPortDedicatedUserData	1.3.6.1.4.1.33.13.1.18.1.45	DisplayString	read-write	The text string to send at the beginning of a connection to a Telnet dedicated service. Corresponds to the value labeled 'UserData:' in the PORT CHARACTERISTICS display.
INT basicSerialPortIpAutoDiscovery	1.3.6.1.4.1.33.13.1.18.1.47	INTEGER	read-write	Control to enable a non-standard method of acquiring the IP address after boot completes via the BOOTP protocol. Corresponds to the value labeled 'IP Address Auto Discovery' in the SERVER CHARACTERISTICS display.
STR basicSerialPortDedicatedKickStartData	1.3.6.1.4.1.33.13.1.18.1.48	DisplayString	read-write	A text string which is used to compare at login time to incoming serial data. A match will initiate a telnet session to a dedicated service. Corresponds to the value labeled 'KickStart:' in the PORT CHARACTERISTICS display.
INT basicSerialPortBreakLength	1.3.6.1.4.1.33.13.1.18.1.50	INTEGER	read-write	Specifies the duration in milliseconds of a remote serial break which is sent via the Telnet Break command. Corresponds directly to the value labeled 'Break Length:' in the PORT CHARACTERISTIC display.
INT basicSerialPortRotaryRoundRobin	1.3.6.1.4.1.33.13.1.18.1.51	INTEGER	read-write	Controls whether a port which participates in an internet rotary is selected in round robin or fixed priority order. Corresponds directly to the value labeled 'Round Robin search:' in the SERVER INTERNET ROTARY display.
INT basicSerialPortWelcomeBeforeAuthentication	1.3.6.1.4.1.33.13.1.18.1.52	INTEGER	read-write	Control to display the basicWelcome message prior to authenticating the user. Corresponds to the presence of the value 'Welcome-Banner-Pre-Authentication' following the label 'Enabled Characteristics' in the PORT CHARACTERISTICS display.
INT basicSerialPortGatewayAutoDiscovery	1.3.6.1.4.1.33.13.1.18.1.53	INTEGER	read-write	Control to enable a non-standard method of acquiring the gateway address after boot completes via the bootp protocol.
INT basicSerialPortSubnetAutoDiscovery	1.3.6.1.4.1.33.13.1.18.1.54	INTEGER	read-write	Control to enable a non-standard method of acquiring the subnet mask after boot completes via the bootp protocol.
INT basicSerialPortRaiseLowerDtr	1.3.6.1.4.1.33.13.1.18.1.55	INTEGER	read-write	A control to to raise or lower the DTR signal from this port by setting it to high or low, respectively. This request will have no effect unless basicSerialPortRaiseControlDtr is enabled. In response to a get-request or get-next-request the agent always returns low for this object.
INT basicSerialPortRaiseControlDtr	1.3.6.1.4.1.33.13.1.18.1.56	INTEGER	read-write	Controls the ability to change the state of DTR using basicSerialPortRaiseLowerDTR. This characteristic is not intended for use with modem ports. Corresponds directly to the presence of 'Control DTR' under the label 'Enabled Characteristics' in the PORT CHARACTERISTICS display. The desired change will not take effect until the port is logged off.
INT basicSerialPortIpConfigureBootp	1.3.6.1.4.1.33.13.1.18.1.57	INTEGER	read-write	Control to use the BOOTP protocol upon startup to learn the unit's own internet address, subnet mask, primary and secondary gateway servers, domain name servers, time server and domain name. This object was moved to the ITOUCH-INTERNET-MIB for InReach agent software version V2.4.
INT basicConsoleLogoutDisconnect	1.3.6.1.4.1.33.13.1.19	INTEGER	read-write	Control for automatic session disconnection when a console port user logs out. Corresponds directly to SERVER CONSOLE LOGOUT and the presence of the label 'Console Logout' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display.
INT basicControlledPorts	1.3.6.1.4.1.33.13.1.20	INTEGER	read-write	Status of Controlled Ports feature. Corresponds directly to the 'Controlled Ports' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. Enabling this feature causes strings of control characters to be sent out on a port upon starting and/or stopping a session
basicPortSessionTable	1.3.6.1.4.1.33.13.1.21		not-accessible	A list of port session entries.
basicPortSessEntry	1.3.6.1.4.1.33.13.1.21.1		not-accessible	Status and parameter values for a basic port session.
INT basicPortPortIndex	1.3.6.1.4.1.33.13.1.21.1.1	INTEGER	read-only	The value of basicPortIndex for the port to which this session belongs. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT basicPortSessIndex	1.3.6.1.4.1.33.13.1.21.1.2	INTEGER	read-only	The session index in the context of the port, a non-zero positive integer. Session indexes within a port need not be sequential. Session indexes may be reused for different ports. For example, port 1 and port 3 may both have a session 2 at the same time. Session indexes may have any valid integer value, with any meaning convenient to the agent implementation. The session identified by a particular value of this index is the same session as identified by charSessIndex in the standard Character MIB.
INT basicSessControlled	1.3.6.1.4.1.33.13.1.21.1.3	INTEGER	read-only	A control to send preconfigured controlled port session strings out the serial port when entering or exiting this session. Corresponds directly to the value labeled 'Controlled' under the Service Mode header in the SESSION display.
INT basicPortSessEncryption	1.3.6.1.4.1.33.13.1.22	INTEGER	read-write	Status of the default encryption value to be set for each session. Corresponds directly to Console Security on SHOW SERVER screen.
INT basicTemperatureUnits	1.3.6.1.4.1.33.13.1.23	INTEGER	read-write	Indicates the units of measurement for the temperature sensors.
INT basicEnvironmentalManagerCircuitBreaker	1.3.6.1.4.1.33.13.1.24	INTEGER	read-only	Indicates whether the circuit breaker is activated.
basicContactClosureOrAlarmInputTable	1.3.6.1.4.1.33.13.1.25		not-accessible	Information about contact closures or alarm inputs.
basicContactClosureOrAlarmInputEntry	1.3.6.1.4.1.33.13.1.25.1		not-accessible	An entry in the basicContactClosureOrAlarmInputTable.
INT basicContactClosureOrAlarmInputValue	1.3.6.1.4.1.33.13.1.25.1.1	INTEGER	read-only	Indicates the state of the contact closure or alarm input.
STR basicContactClosureOrAlarmInputName	1.3.6.1.4.1.33.13.1.25.1.2	DisplayString	read-write	The name used to identify this contact closure or alarm input.
INT basicContactClosureOrAlarmInputTrapEnable	1.3.6.1.4.1.33.13.1.25.1.3	INTEGER	read-write	Control to send trap when contact closure or alarm input changes state.
INT basicContactClosureOrAlarmInputFaultSeverity	1.3.6.1.4.1.33.13.1.25.1.4	INTEGER	read-write	Control to determine the severity level associated with the trap sent out when a fault occurs for a given contact closure or alarm input.
INT basicContactClosureOrAlarmInputFaultState	1.3.6.1.4.1.33.13.1.25.1.5	INTEGER	read-write	Control to indicate which state, open or closed, represents the fault condition. The other state is the cleared condition.
INT basicContactClosureOrAlarmInputStatus	1.3.6.1.4.1.33.13.1.25.1.6	INTEGER	read-only	Indicates the current status of the contact closure or alarm input. If the basicContactClosureOrAlarmInputValue matches the fault state, then the status is equal to the fault severity. Otherwise the status is cleared.
STR basicContactClosureOrAlarmInputZone	1.3.6.1.4.1.33.13.1.25.1.7	DisplayString	read-write	The name used to identify the zone where the equipment resides.
STR basicContactClosureOrAlarmInputRelatedEquipment	1.3.6.1.4.1.33.13.1.25.1.8	DisplayString	read-write	The name used to identify related equipment.
STR basicContactClosureOrAlarmInputSiteId	1.3.6.1.4.1.33.13.1.25.1.9	DisplayString	read-write	The name used to identify the site where the unit resides.
INT basicContactClosureOrAlarmInputIndex	1.3.6.1.4.1.33.13.1.25.1.10	INTEGER	read-only	An index which uniquely identifies the contact closure or alarm input.
STR basicContactClosureOrAlarmInputManufacturer	1.3.6.1.4.1.33.13.1.25.1.11	DisplayString	read-write	The name used to identify the manufacturer of this equipment.
STR basicContactClosureOrAlarmInputModel	1.3.6.1.4.1.33.13.1.25.1.12	DisplayString	read-write	The model name of this equipment.
basicPowerOutletTable	1.3.6.1.4.1.33.13.1.26		not-accessible	Information about Environmental Manager Power Outlets.
basicPowerOutletEntry	1.3.6.1.4.1.33.13.1.26.1		not-accessible	An entry in the basicPowerOutletTable.
INT basicPowerOutletOnOff	1.3.6.1.4.1.33.13.1.26.1.1	INTEGER	read-write	Controls turning on or off the power for the device connected to this power outlet.
INT basicPowerOutletReboot	1.3.6.1.4.1.33.13.1.26.1.2	INTEGER	read-write	Controls rebooting of the device attached this power outlet.
STR basicPowerOutletName	1.3.6.1.4.1.33.13.1.26.1.3	DisplayString	read-write	A name used to identify this power outlet.
INT basicPowerOutletRedundant	1.3.6.1.4.1.33.13.1.26.1.4	INTEGER	read-only	Controls whether power outlets in bank A have redundant outlets in bank B. When enabled, powering on an outlet in bank A will simultaneously power on the corresponding outlet number in bank B.
STR basicPowerOutletConsoleName	1.3.6.1.4.1.33.13.1.26.1.5	DisplayString	read-write	A name used to identify a console port on a unit with power outlet managment.
INT basicPowerOutletHighCurrent	1.3.6.1.4.1.33.13.1.26.1.6	INTEGER	read-write	A control to indicate a high current unit is attached to this power outlet. When enabled the high current unit will provide current when it detects no power from the power outlet; and will stop the current when the outlet resumes power. This control only works on those InReach devices which support the high current unit such as the IRMGR0. Corresponds directly to the value labeled 'HCNC Setting' in the INREACH MANAGER OUTLET STATUS display.
INT basicPowerOutletIndex	1.3.6.1.4.1.33.13.1.26.1.10	INTEGER	read-only	An index which uniquely identifies a power outlet.
basicTemperatureHumiditySensor	1.3.6.1.4.1.33.13.1.27
basicTemperatureSensorTable	1.3.6.1.4.1.33.13.1.27.1		not-accessible	Information about Environmental Manager Temperature Sensors.
basicTemperatureSensorEntry	1.3.6.1.4.1.33.13.1.27.1.1		not-accessible	An entry in the basicTemperatureSensorTable.
INT basicTempTrapHighThreshold	1.3.6.1.4.1.33.13.1.27.1.1.1	INTEGER	read-write	The temperature at or above which a sensorThresholdTrap is generated.
INT basicTempTrapLowThreshold	1.3.6.1.4.1.33.13.1.27.1.1.2	INTEGER	read-write	The temperature at or below which a sensorThresholdTrap is generated.
INT basicTemperatureSensor	1.3.6.1.4.1.33.13.1.27.1.1.3	INTEGER	read-write	Controls the enabling or disabling of a temperature sensor.
INT basicTemperatureValue	1.3.6.1.4.1.33.13.1.27.1.1.4	INTEGER	read-write	The current temperature reading for this sensor.
INT basicTemperatureAlarmSeverity	1.3.6.1.4.1.33.13.1.27.1.1.5	INTEGER	read-write	Control to determine the severity level associated with the trap sent out when the temperature reading is out-of-bounds.
INT basicTemperatureAlarmStatus	1.3.6.1.4.1.33.13.1.27.1.1.6	INTEGER	read-only	Indicates the current status of the temperature sensor. If the basicTemperatureValue falls within the normal range, the status is cleared. Otherwise the status matches the alarm severity level.
INT basicTemperatureSensorIndex	1.3.6.1.4.1.33.13.1.27.1.1.10	INTEGER	read-only	An index which uniquely identifies a temperature sensor.
basicHumiditySensorTable	1.3.6.1.4.1.33.13.1.27.2		not-accessible	Information about Environmental Manager Humidity Sensors.
basicHumiditySensorEntry	1.3.6.1.4.1.33.13.1.27.2.1		not-accessible	An entry in the basicHumiditySensorTable.
INT basicHumidityTrapHighThreshold	1.3.6.1.4.1.33.13.1.27.2.1.1	INTEGER	read-write	The humidity at or above which a sensorThresholdTrap is generated.
INT basicHumidityTrapLowThreshold	1.3.6.1.4.1.33.13.1.27.2.1.2	INTEGER	read-write	The humidity at or below which a sensorThresholdTrap is generated.
INT basicHumiditySensor	1.3.6.1.4.1.33.13.1.27.2.1.3	INTEGER	read-write	Controls the enabling or disabling of a humidity sensor.
INT basicHumidityValue	1.3.6.1.4.1.33.13.1.27.2.1.4	INTEGER	read-write	The current humidity reading for this sensor.
INT basicHumidityAlarmSeverity	1.3.6.1.4.1.33.13.1.27.2.1.5	INTEGER	read-write	Control to indicate the severity level associated with the trap sent out when the humidity reading is out-of-bounds.
INT basicHumidityAlarmStatus	1.3.6.1.4.1.33.13.1.27.2.1.6	INTEGER	read-only	Indicates the current status of the humidity sensor. If the basicHumidityValue falls within the normal range, the status is cleared. Otherwise the status matches the alarm severity level.
INT basicHumiditySensorIndex	1.3.6.1.4.1.33.13.1.27.2.1.10	INTEGER	read-only	An index which uniquely identifies a humidity sensor.
basicControlSignalTable	1.3.6.1.4.1.33.13.1.28		not-accessible	Information about Environmental Manager Control Signal points.
basicControlSignalEntry	1.3.6.1.4.1.33.13.1.28.1		not-accessible	An entry in the basicControlSignalTable.
INT basicControlSignalValue	1.3.6.1.4.1.33.13.1.28.1.1	INTEGER	read-write	Sets and reads the state of the control signal point.
INT basicControlSignalIndex	1.3.6.1.4.1.33.13.1.28.1.10	INTEGER	read-only	An index which uniquely identifies a control signal point.
INT basicPowerAlarmTimer	1.3.6.1.4.1.33.13.1.29	INTEGER	read-write	The polling interval in seconds for the fuse and power supply status. An alarm trap is issued on power failure.
basicControlOutputTable	1.3.6.1.4.1.33.13.1.30		not-accessible	Information about controlled output distribution points.
basicControlOutputEntry	1.3.6.1.4.1.33.13.1.30.1		not-accessible	An entry in the basicControlOutputTable.
INT basicControlOutputSignalDtrRts	1.3.6.1.4.1.33.13.1.30.1.1	INTEGER	read-write	Controls the raising or lowering of a signal on a distribution control signal point. The signal is DTR when the basicControlOutputIndex is odd, or RTS when the basicControlOutputIndex is even.
STR basicControlOutputName	1.3.6.1.4.1.33.13.1.30.1.2	DisplayString	read-write	The name used to identify this distribution control signal point.
INT basicControlOutputIndex	1.3.6.1.4.1.33.13.1.30.1.10	INTEGER	read-only	An index which uniquely identifies a distribution control signal point.
INT basicPowerStatusFuseA	1.3.6.1.4.1.33.13.1.31	INTEGER	read-only	Indicates the status of fuse bank A.
INT basicPowerStatusFuseB	1.3.6.1.4.1.33.13.1.32	INTEGER	read-only	Indicates the status of fuse bank B.
INT basicPowerSupplyStatusA	1.3.6.1.4.1.33.13.1.33	INTEGER	read-only	Indicates the status of power supply A.
INT basicPowerSupplyStatusB	1.3.6.1.4.1.33.13.1.34	INTEGER	read-only	Indicates the status of power supply B.
basicPortTrapTable	1.3.6.1.4.1.33.13.1.35		not-accessible	A list of traps associated with signal control changes on ports.
basicPortTrapEntry	1.3.6.1.4.1.33.13.1.35.1		not-accessible	Administrative status of signal change traps for a hardware port.
INT basicPortTrapIndex	1.3.6.1.4.1.33.13.1.35.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by rs232PortIndex in the standard rs232 MIB.
INT basicPortSignalName	1.3.6.1.4.1.33.13.1.35.1.2	INTEGER	read-only	Identification of the hardware signal as specified in RFC1659 as follows: rts Request to Send cts Clear to Send dsr Data Set Ready dts Data Terminal Ready ri Ring Indicator dcd Received Line Signal Detector Some agents do not support DSR since its pin is shared with DCD.
INT basicPortTrapStatus	1.3.6.1.4.1.33.13.1.35.1.3	INTEGER	read-write	Control to toggle the sending of a trap on a specific signal change on a physical port. One must logout the port prior to this taking effect.
basicAlarmMasterInputTable	1.3.6.1.4.1.33.13.1.36		not-accessible	Information about the high density alarm manager's alarm inputs.
basicAlarmMasterInputEntry	1.3.6.1.4.1.33.13.1.36.1		not-accessible	An entry in the basicAlarmMasterInputTable.
INT basicAlarmMasterInputPort	1.3.6.1.4.1.33.13.1.36.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT basicAlarmMasterInputSlot	1.3.6.1.4.1.33.13.1.36.1.2	INTEGER	read-only	An index value that uniquely identifies a slot of alarm points on a given high density alarm port.
INT basicAlarmMasterInputPoint	1.3.6.1.4.1.33.13.1.36.1.3	INTEGER	read-only	An index value that uniquely identifies an alarm point within an alarm slot on a high density alarm port.
STR basicAlarmMasterInputName	1.3.6.1.4.1.33.13.1.36.1.4	DisplayString	read-write	The name used to identify this alarm point.
INT basicAlarmMasterInputTrapEnable	1.3.6.1.4.1.33.13.1.36.1.5	INTEGER	read-write	Control to send a trap when the alarm input changes state.
INT basicAlarmMasterControlOutputSignal	1.3.6.1.4.1.33.13.1.36.1.6	INTEGER	read-write	Control to toggle the output signal for an alarm point.
INT basicAlarmMasterInputEnable	1.3.6.1.4.1.33.13.1.36.1.7	INTEGER	read-write	Control to toggle whether this alarm point is active.
INT basicAlarmMasterInputDebounceInterval	1.3.6.1.4.1.33.13.1.36.1.8	INTEGER	read-write	Amount of time in seconds to debounce a signal change before triggering an alarm.
INT basicAlarmMasterInputFaultSeverity	1.3.6.1.4.1.33.13.1.36.1.9	INTEGER	read-write	Control to determine the severity level associated with the trap sent out when a fault occurs for this alarm input point.
INT basicAlarmMasterInputFaultState	1.3.6.1.4.1.33.13.1.36.1.10	INTEGER	read-write	Control to indicate which state, open or closed, represents the fault condition for this alarm input point. The other state is the cleared condition.
INT basicAlarmMasterInputStatus	1.3.6.1.4.1.33.13.1.36.1.11	INTEGER	read-only	Indicates the current status of the alarm input point. If the basicAlarmMasterInputValue matches the fault state, then the status is equal to the fault severity. Otherwise the status is cleared.
INT basicAlarmMasterInputValue	1.3.6.1.4.1.33.13.1.36.1.12	INTEGER	read-only	Indicates the current state of the alarm input point.
INT basicAlarmMasterDisplay	1.3.6.1.4.1.33.13.1.36.1.13	INTEGER	read-write	Control to toggle the display of the alarm status for this point in the display window of the high density alarm unit.
basicPowerMasterOutletTable	1.3.6.1.4.1.33.13.1.37		not-accessible	Information about power master outlets.
basicPowerMasterOutletEntry	1.3.6.1.4.1.33.13.1.37.1		not-accessible	An entry in the basicPowerMasterOutletTable.
INT basicPowerMasterPortIndex	1.3.6.1.4.1.33.13.1.37.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by the charPortIndex in the standard Character MIB.
INT basicPowerMasterOutletIndex	1.3.6.1.4.1.33.13.1.37.1.2	INTEGER	read-only	An index which uniquely identifies a power master outlet.
STR basicPowerMasterOutletName	1.3.6.1.4.1.33.13.1.37.1.3	DisplayString	read-write	The name used to identify this power master outlet.
INT basicPowerMasterOutletState	1.3.6.1.4.1.33.13.1.37.1.4	INTEGER	read-write	Switches the power master outlet on or off. There may be a noticeable time delay while processing a get-request for this object.
STR basicPowerMasterOutletAmperageStatus	1.3.6.1.4.1.33.13.1.37.1.5	DisplayString	read-only	Indicates the current amperage drawn at this outlet. There may be a noticeable time delay while processing a get-request for this object.
basicControlOutputRelayTable	1.3.6.1.4.1.33.13.1.38		not-accessible	Information about controlled output relays.
basicControlOutputRelayEntry	1.3.6.1.4.1.33.13.1.38.1		not-accessible	An entry in the basicControlOutputRelayTable.
INT basicControlOutputRelayIndex	1.3.6.1.4.1.33.13.1.38.1.1	INTEGER	read-only	An index which uniquely identifies a control output relay.
STR basicControlOutputRelayName	1.3.6.1.4.1.33.13.1.38.1.2	DisplayString	read-write	The name used to identify this control output relay.
INT basicControlOutputRelayState	1.3.6.1.4.1.33.13.1.38.1.3	INTEGER	read-write	Controls the opening or closing of the control output relay.
INT basicControlOutputRelayStatus	1.3.6.1.4.1.33.13.1.38.1.4	INTEGER	read-only	Indicates the current status of the control output relay.
STR basicAutoProtocolDetectMessage	1.3.6.1.4.1.33.13.1.100	DisplayString	read-write	The text string sent as a prompt message out the port at the beginning of auto protocol detection mode. Corresponds to the value labeled 'APD Message' in the SERVER UNIT display.
xQueue	1.3.6.1.4.1.33.13.2
INT queueLimit	1.3.6.1.4.1.33.13.2.1	INTEGER	read-write	The maximum number of entries that can be made in the Queue table. The value -1 indicates the imit is available memory. Corresponds directly to SERVER QUEUE LIMIT and the value labeled 'Queue Limit:' in the SERVER CHARACTERISTICS display.
GAU queueHigh	1.3.6.1.4.1.33.13.2.2	Gauge	read-only	The highest value of queueNumber since system initialization. Corresponds directly to the value labeled 'Queue Entries' and 'High' in the SERVER STATUS display.
GAU queueNumber	1.3.6.1.4.1.33.13.2.3	Gauge	read-only	The number of entries in the Queue table. Corresponds directly to the value labeled 'Queue Entries' and 'Cur' in the SERVER STATUS display.
queueTable	1.3.6.1.4.1.33.13.2.4		not-accessible	A list of queue entries.
queueEntry	1.3.6.1.4.1.33.13.2.4.1		not-accessible	Parameter values for a queue entry.
INT queueJob	1.3.6.1.4.1.33.13.2.4.1.1	INTEGER	read-only	The job number of a queued request. Corresponds directly to the value labeled 'Entry' in the QUEUE display.
INT queueStatus	1.3.6.1.4.1.33.13.2.4.1.2	INTEGER	read-write	The status of a queue entry. Set to 'invalid' to remove the entry, which corresponds directly to the REMOVE QUEUE ENTRY command. Actual removal of the entry is implementation specific.
STR queueSourceName	1.3.6.1.4.1.33.13.2.4.1.3	DisplayString	read-only	The name of the system that originated the queue entry. Corresponds directly to the value labeled 'Source Node' in the QUEUE display.
STR queueServiceName	1.3.6.1.4.1.33.13.2.4.1.4	DisplayString	read-only	The name of the service for which the originator is waiting. Corresponds directly to the value labeled 'Service' in the QUEUE display.
INT queueServicePortIndex	1.3.6.1.4.1.33.13.2.4.1.5	INTEGER	read-only	The charPortIndex of the port for which the originator is waiting, if supplied by the originator. As defined in the standard Character MIB. Corresponds indirectly to the port number part of the value labeled 'Port Name' in the QUEUE display.
STR queueServicePortName	1.3.6.1.4.1.33.13.2.4.1.6	DisplayString	read-only	The name of the port for which the originator is waiting, if supplied by the originator. Corresponds directly to the port name part of the value labeled 'Port Name' in the SERVER QUEUE display.
queuePortTable	1.3.6.1.4.1.33.13.2.5		not-accessible	A list of queuing-related character port entries.
queuePortEntry	1.3.6.1.4.1.33.13.2.5.1		not-accessible	Queuing parameter values for a port.
INT queuePortIndex	1.3.6.1.4.1.33.13.2.5.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT queuePortQueuing	1.3.6.1.4.1.33.13.2.5.1.2	INTEGER	read-write	Control for allowing queued requests for using the port. Corresponds directly to PORT QUEUING and the presence of the label 'Queuing' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
xMenu	1.3.6.1.4.1.33.13.3
GAU menuNumber	1.3.6.1.4.1.33.13.3.1	Gauge	read-only	The number of entries in the Menu table. Corresponds indirectly to SERVER MENU display.
STR menuContinuePrompt	1.3.6.1.4.1.33.13.3.2	DisplayString	read-write	The text to use when prompting a menu user to press RETURN to continue. Corresponds directly to SERVER MENU CONTINUE PROMPT and the value labeled 'Menu Continue Prompt:' in the SERVER MENU display.
STR menuSelectionPrompt	1.3.6.1.4.1.33.13.3.3	DisplayString	read-write	The text to use when prompting a menu user for a menu selection. Corresponds directly to SERVER MENU PROMPT and the value labeled 'Menu Prompt:' in the SERVER MENU display.
menuTable	1.3.6.1.4.1.33.13.3.4		not-accessible	A list of menu entries.
menuEntry	1.3.6.1.4.1.33.13.3.4.1		not-accessible	Parameter values for a menu entry.
INT menuIndex	1.3.6.1.4.1.33.13.3.4.1.1	INTEGER	read-only	The index number of a menu entry. Corresponds directly to the numbers down the left of the SERVER MENU display.
INT menuStatus	1.3.6.1.4.1.33.13.3.4.1.2	INTEGER	read-write	The status of a the entry. Set to 'invalid' to remove the entry, which corresponds directly to the CLEAR SERVER MENU command. Actual removal of the entry is implementation specific.
STR menuText	1.3.6.1.4.1.33.13.3.4.1.3	DisplayString	read-write	The text to be displayed in the menu. Corresponds directly to the line next to the entry number in the SERVER MENU display.
STR menuCommand	1.3.6.1.4.1.33.13.3.4.1.4	DisplayString	read-write	The commands to execute when the user chooses the menu entry. Corresponds directly second line following the entry number in the SERVER MENU display.
menuPortTable	1.3.6.1.4.1.33.13.3.5		not-accessible	A list of menu-related character port entries.
menuPortEntry	1.3.6.1.4.1.33.13.3.5.1		not-accessible	Menu parameter values for a port.
INT menuPortIndex	1.3.6.1.4.1.33.13.3.5.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT menuPortMenuStatus	1.3.6.1.4.1.33.13.3.5.1.2	INTEGER	read-write	Control for menu operation on the port. Corresponds indirectly to PORT MENU and PORT PRIVILEGED MENU and the presence of the labels 'Menu' and 'Privileged Menu' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT menuPortNestedMenuStatus	1.3.6.1.4.1.33.13.3.5.1.3	INTEGER	read-write	Control for nested menu operation on the port. Corresponds indirectly to PORT NESTED MENU and the presence of the label 'Nested Menu' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT menuPortNestedMenuPrivilege	1.3.6.1.4.1.33.13.3.5.1.4	INTEGER	read-write	Control for nested privileged menu operation on the port. Corresponds indirectly to PORT NESTED PRIVILEGED MENU and the presence of the label 'Nested Privileged Menu' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT menuPortNestedTopLevel	1.3.6.1.4.1.33.13.3.5.1.5	INTEGER	read-write	The top level nested menu to select from the menu definition file.
STR menuNestedName	1.3.6.1.4.1.33.13.3.6	DisplayString	read-write	Name of the script file containing the nested menu.
INT menuNestedScriptMaximum	1.3.6.1.4.1.33.13.3.7	INTEGER	read-write	Maximum number of temporary storage bytes for a nested menu script file. If not zero, the nested menu function is enabled.
INT menuNestedSystemName	1.3.6.1.4.1.33.13.3.8	INTEGER	read-write	Control to request to download a menu script which is unique for this unit by prepending the sysLocalName of this unit to the nestedMenuName.
INT menuNestedEthernet	1.3.6.1.4.1.33.13.3.9	INTEGER	read-write	Control to request to download a menu script which is unique for this unit by prepending the Ethernet address, or 802.3 MAC address, of this unit to the nestedMenuName.
xNetLogin	1.3.6.1.4.1.33.13.4
INT netLoginNumber	1.3.6.1.4.1.33.13.4.1	INTEGER	read-only	The number of entries in the Network Login Server table.
netLoginServerTable	1.3.6.1.4.1.33.13.4.2		not-accessible	A list of network login server entries.
netLoginServerEntry	1.3.6.1.4.1.33.13.4.2.1		not-accessible	Network login parameter values for a server entry.
STR netLoginServerName	1.3.6.1.4.1.33.13.4.2.1.1	DisplayString	read-only	The name of a network login server, suitable for resolution to a network address. Corresponds directly to host portion of SERVER SCRIPT SERVER and the value labeled 'Script Host' in the SERVER PARAMETER SERVER display.
INT netLoginServerStatus	1.3.6.1.4.1.33.13.4.2.1.2	INTEGER	read-write	Status of this entry. Set to 'invalid' to remove the entry, which corresponds directly to the CLEAR SERVER SCRIPT SERVER command. Actual removal of the entry is implementation specific.
STR netLoginServerPath	1.3.6.1.4.1.33.13.4.2.1.3	DisplayString	read-write	The full path name to the script file that is identified by the user name. Corresponds directly to path portion of SERVER SCRIPT SERVER and the value labeled 'Script Path' in the SERVER PARAMETER SERVER display. Defaults to the NULL string when a new entry is created.
STR netLoginServerSeparator	1.3.6.1.4.1.33.13.4.2.1.4	DisplayString	read-write	The single character string that will be inserted between the components of a file's path on the script server. Defaults to the NULL string when a new entry is created. Corresponds directly to the separator portion of SERVER SCRIPT SERVER display.
netLoginPortTable	1.3.6.1.4.1.33.13.4.3		not-accessible	A list of network login character port entries.
netLoginPortEntry	1.3.6.1.4.1.33.13.4.3.1		not-accessible	Network login parameter values for a port.
INT netLoginPortIndex	1.3.6.1.4.1.33.13.4.3.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT netLoginPortScriptUse	1.3.6.1.4.1.33.13.4.3.1.2	INTEGER	read-write	Control for the script action taken when a user logs in on the port. Corresponds directly to PORT SCRIPT LOGIN and the value labeled 'Script Login:' in the PORT ALTERNATE CHARACTERISTICS display.
INT netLoginPortScriptEcho	1.3.6.1.4.1.33.13.4.3.1.3	INTEGER	read-write	Control for display of script operation on the port when running a script. Corresponds directly to PORT SCRIPT ECHO and the presence of the label 'Script Echo' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
ADR netLoginPortLoaderAddressType	1.3.6.1.4.1.33.13.4.3.1.4	AddressType	read-only	The type of network address contained in netLoginPortLoaderAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. Corresponds indirectly to the address part of the value labeled 'Script Loaded From:' in the PORT STATUS display.
OCT netLoginPortLoaderAddress	1.3.6.1.4.1.33.13.4.3.1.5	OCTET STRING	read-only	The network address of the server that provided the script for the current port login. Corresponds directly the address part of the value labeled 'Script Loaded From:' in the PORT STATUS display.
STR netLoginPortLoaderFile	1.3.6.1.4.1.33.13.4.3.1.6	DisplayString	read-only	The path and file name of the script used for the current port login. Corresponds directly the file name part of the value labeled 'Script Loaded From:' in the PORT STATUS display.
STR netLoginPortExecuteFile	1.3.6.1.4.1.33.13.4.3.1.7	DisplayString	read-write	The path and file name of a script to be executed immediately on the port. Corresponds directly the file name in the SCRIPT command.
xDial	1.3.6.1.4.1.33.13.5
dialPortTable	1.3.6.1.4.1.33.13.5.1		not-accessible	A list of dial character port entries.
dialPortEntry	1.3.6.1.4.1.33.13.5.1.1		not-accessible	Dial parameter values for a port.
INT dialPortIndex	1.3.6.1.4.1.33.13.5.1.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT dialPortDialback	1.3.6.1.4.1.33.13.5.1.1.2	INTEGER	read-write	Control for use of dialback when a user logs in on the port. Corresponds directly to PORT DIALBACK and the presence of the label 'Dialback' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT dialPortDialbackTimeout	1.3.6.1.4.1.33.13.5.1.1.3	INTEGER	read-write	The number of seconds to wait for remote modem response when dialing back. Corresponds directly to PORT DIALBACK TIMEOUT and the value labeled 'Dialback Timeout:' in the PORT ALTERNATE CHARACTERISTICS display.
INT dialPortDialout	1.3.6.1.4.1.33.13.5.1.1.4	INTEGER	read-write	A control to determine the state of a remote port after it has been logged out from the remote side of the connection. none will log out the port, query will ask user what to do, slip and ppp will revert to those protocols
INT dialPortDialbackNoUsername	1.3.6.1.4.1.33.13.5.1.1.5	INTEGER	read-write	Control which when enabled on a dialback port will not prompt for a username upon dialing back. Instead the original username is reused.
xSessionLog	1.3.6.1.4.1.33.13.6
INT sessionLogLimit	1.3.6.1.4.1.33.13.6.1	INTEGER	read-write	The maximum number of entries allowed in the Session Log table. Corresponds directly to SERVER ACCOUNTING ENTRIES and the value labeled 'Accounting Entries:' in the SERVER CHARACTERISTICS display.
sessionLogTable	1.3.6.1.4.1.33.13.6.2		not-accessible	A list of session log entries.
sessionLogEntry	1.3.6.1.4.1.33.13.6.2.1		not-accessible	Parameter values for a session log entry.
INT sessionLogIndex	1.3.6.1.4.1.33.13.6.2.1.1	INTEGER	read-only	The index number of a session log entry. Corresponds directly to the order of the displayed records in the SERVER ACCOUNTING display. The maximum value is sessionLogLimit.
INT sessionLogConnectionID	1.3.6.1.4.1.33.13.6.2.1.2	INTEGER	read-only	An indentifying number for records relating to the same connection, that is, the connect and disconnect records, either of which can be missing. Corresponds directly to value labeled 'Entry' the SERVER ACCOUNTING display.
INT sessionLogPort	1.3.6.1.4.1.33.13.6.2.1.3	INTEGER	read-only	An index value that uniquely identifies the port where the event took place. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB. Corresponds directly to the value labeled 'Port' in the SERVER ACCOUNTING display.
INT sessionLogEvent	1.3.6.1.4.1.33.13.6.2.1.4	INTEGER	read-only	The type of event. Corresponds directly to the alphabetic part of the value labeled 'Type' in the SERVER ACCOUNTING display. Type 15 is used by internal processes that call the session log function with an already formatted message.
INT sessionLogEventDetail	1.3.6.1.4.1.33.13.6.2.1.5	INTEGER	read-only	The detailed reason for the event. Corresponds directly to the numeric part of the value labeled 'Type' in the SERVER ACCOUNTING display.
STR sessionLogUserName	1.3.6.1.4.1.33.13.6.2.1.6	DisplayString	read-only	The user name logged in on the port when the event occurred. Corresponds directly to the value labeled 'Username' in the SERVER ACCOUNTING display.
STR sessionLogRemoteName	1.3.6.1.4.1.33.13.6.2.1.7	DisplayString	read-only	The name of the session remote partner. Corresponds directly to the value labeled 'Destination' in the SERVER ACCOUNTING display.
DAT sessionLogConnectTime	1.3.6.1.4.1.33.13.6.2.1.8	DateTime	read-only	The date and time that session connection occurred. Corresponds directly to the value labeled 'Connect Time' in the SERVER ACCOUNTING display.
DAT sessionLogDisconnectTime	1.3.6.1.4.1.33.13.6.2.1.9	DateTime	read-only	The date and time that session disconnection occurred. Corresponds directly to the value labeled 'Disconnect Time' in the SERVER ACCOUNTING display.
CTR sessionLogInCharacters	1.3.6.1.4.1.33.13.6.2.1.10	Counter	read-only	The number of characters that came into the port for the session. Corresponds directly to the value labeled 'Bytes In' in the SERVER ACCOUNTING display.
CTR sessionLogOutCharacters	1.3.6.1.4.1.33.13.6.2.1.11	Counter	read-only	The number of characters that went out of the port for the session. Corresponds directly to the value labeled 'Bytes Out' in the SERVER ACCOUNTING display.
INT sessionLogVerboseEvent	1.3.6.1.4.1.33.13.6.2.1.12	INTEGER	read-only	When logging in 'verbose' mode, the event that occured.
INT sessionLogX25Direction	1.3.6.1.4.1.33.13.6.2.1.13	INTEGER	read-only	The initial direction for an X.25 connection. A value of 0 is returned if the session is not X25
STR sessionLogVerboseMessage	1.3.6.1.4.1.33.13.6.2.1.14	DisplayString	read-only	Text describing the event that was logged.
OCT sessionLogX25CallerAddress	1.3.6.1.4.1.33.13.6.2.1.15	OCTET STRING	read-only	For an X.25 connection, the X.121 source address.
OCT sessionLogX25CalledAddress	1.3.6.1.4.1.33.13.6.2.1.16	OCTET STRING	read-only	For an X.25 connection, the X.121 destination address.
INT sessionLogX25DisconnectCause	1.3.6.1.4.1.33.13.6.2.1.17	INTEGER	read-only	For a terminated X.25 connection, the standard, X.25 cause code.
INT sessionLogX25DisconnectDiagnostic	1.3.6.1.4.1.33.13.6.2.1.18	INTEGER	read-only	For a terminated X.25 connection, the standard, X.25 diagnostic code.
INT sessionLogHostType	1.3.6.1.4.1.33.13.6.3	INTEGER	read-write	The type of host to which session log events are to be sent.
OCT sessionLogHostAddress	1.3.6.1.4.1.33.13.6.4	OCTET STRING	read-write	The address of the host to receive events.
INT sessionLogVerbose	1.3.6.1.4.1.33.13.6.5	INTEGER	read-write	Control for verbose logging.
INT sessionLogPriority	1.3.6.1.4.1.33.13.6.6	INTEGER	read-write	The largest priority number for the system to log. Higher numbered (lower priority) events will not be logged.
INT sessionLogEmpty	1.3.6.1.4.1.33.13.6.7	INTEGER	read-write	Control to empty the log. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes the log to be emptied.
INT sessionLogFacility	1.3.6.1.4.1.33.13.6.8	INTEGER	read-write	The UNIX facility level that server originated accounting messages are logged to.
INT sessionLogReliable	1.3.6.1.4.1.33.13.6.9	INTEGER	read-write	Control for reliable logging. Corresponds directly to the presence of the label 'Reliable Accounting' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display.
INT sessionLogHostSecondaryType	1.3.6.1.4.1.33.13.6.10	INTEGER	read-write	The type of secondary host to which session log events are to be sent. This value should be set to unix when configuring a non-zero sessionLogHostSecondaryAddress. Corresponds to the presence of the label 'SYSLOGD Host2' following the label 'Daemon(s)' in the SERVER UNIT display.
OCT sessionLogHostSecondaryAddress	1.3.6.1.4.1.33.13.6.11	OCTET STRING	read-write	The address of a secondary host to receive events. Corresponds directly to the value labeled 'SYSLOGD Host2' in the SERVER UNIT display.
INT sessionLogZeroAccountingAll	1.3.6.1.4.1.33.13.6.12	INTEGER	read-write	A control to clear all entries in the accounting log including command log entries. Corresponds directly to the command CLEAR SERVER ACCOUNTING ALL. In response to a get-request or get-next-request the agent always returns ready for this value.
INT sessionLogZeroCommandLogging	1.3.6.1.4.1.33.13.6.13	INTEGER	read-write	A control to clear all command log entries. Corresponds directly to the command CLEAR SERVER COMMAND LOGGING. In response to a get-request or get-next-request the agent always returns ready for this value.
INT sessionLogTl1AutonomousLogSize	1.3.6.1.4.1.33.13.6.14	INTEGER	read-write	The size in bytes of the TL1 autonomous log, which records alarms. A change in log size will not take effect until rebooting the unit.
INT sessionLogTl1CommandLogSize	1.3.6.1.4.1.33.13.6.15	INTEGER	read-write	The size in bytes of the TL1 command log, which records all TL1 commands entered on this server. A change in log size will not take effect until rebooting the unit.
INT sessionLogZeroDataLogging	1.3.6.1.4.1.33.13.6.16	INTEGER	read-write	A control to clear all data log entries. Corresponds directly to the command CLEAR SERVER DATA LOGGING. In response to a get-request or get-next-request the agent always returns ready for this value.
INT sessionLogZeroAlarmLogging	1.3.6.1.4.1.33.13.6.17	INTEGER	read-write	Control to clear all alarm log entries. In response to a get-request or a get-next-request the agent always returns ready for this value.
xCcl	1.3.6.1.4.1.33.13.7
cclParsedScriptTable	1.3.6.1.4.1.33.13.7.1		not-accessible	A list of parsed CCL scripts.
cclParsedScriptEntry	1.3.6.1.4.1.33.13.7.1.1		not-accessible	Parsed CCL script information.
STR cclScriptName	1.3.6.1.4.1.33.13.7.1.1.1	DisplayString	read-only	The name of a CCL script file that has been loaded from a script server. Corresponds directly to the name in a SERVER CCL command and the value labeled 'CCL name:' in the PORT CHARACTERISTICS display.
INT cclScriptControl	1.3.6.1.4.1.33.13.7.1.1.2	INTEGER	read-write	Control for maintaining the CCL script. The refresh action consists of retrieving the script by name from a script server and parsing it into an executable format. This may be used to add an entry to the table or refresh an existing entry with a new version of the CCL script from the server. This command may take ten seconds or more to complete and may fail if the script file cannot be retrieved or an error is encountered in parsing the CCL script. An error value of genErr is returned upon refresh failure. The refresh action corresponds directly to the commnd: REFRESH SERVER CCL. Setting this field to delete causes a script that is NOT being referenced by any ports to be removed from the list and its memory freed. This action corresponds directly to the command: DELETE SERVER CCL. An error value of badValue is returned upon delete failure.
cclPortTable	1.3.6.1.4.1.33.13.7.2		not-accessible	A list of ccl character port entries.
cclPortEntry	1.3.6.1.4.1.33.13.7.2.1		not-accessible	CCL parameter values for a port.
STR cclPortCclName	1.3.6.1.4.1.33.13.7.2.1.1	DisplayString	read-write	The name of the ARAP modem CCL script file.
INT cclPortModemAudible	1.3.6.1.4.1.33.13.7.2.1.2	INTEGER	read-write	This boolean indicates if the CCL script should put the modem into audible mode.
xBroadcastGroup	1.3.6.1.4.1.33.13.8
broadcastGroupTable	1.3.6.1.4.1.33.13.8.1		not-accessible	A list of broadcast groups.
broadcastGroupEntry	1.3.6.1.4.1.33.13.8.1.1		not-accessible	Broadcast group information.
INT broadcastGroupIndex	1.3.6.1.4.1.33.13.8.1.1.1	INTEGER	read-only	An index value that uniquely identifies a broadcast group.
INT broadcastGroupStatus	1.3.6.1.4.1.33.13.8.1.1.2	INTEGER	read-write	A status value for the broadcast group. The value 'enabled' means that the group is active and broadcasting data whereas 'disabled' means that the group is not active.
INT broadcastGroupMaster	1.3.6.1.4.1.33.13.8.1.1.3	INTEGER	read-write	An index value that uniquely identifies the Master Broadcast Port for this group. The port provided in this object is the same port as identified by charPortIndex in the standard Character MIB.
OCT broadcastGroupSlaves	1.3.6.1.4.1.33.13.8.1.1.4	OCTET STRING	read-write	A bitmap representing the ports included in this broadcast group. A bit with a value of '1' means the corresponding port is included in the broadcast group whereas a value of '0' indicates that the port is not part of the broadcast group.
OCT broadcastGroupSlavesBroadcastOnly	1.3.6.1.4.1.33.13.8.1.1.5	OCTET STRING	read-write	A bitmap representing the ports set up to discard input data and transmit only the broadcast data on the line. A bit set to '1' means that the corresponding port will only broadcast the data and discard any input.
INT broadcastGroupSlaveTcpPort	1.3.6.1.4.1.33.13.8.1.1.6	INTEGER	read-write	A TCP port number on which the broadcast group process will listen for incoming TCP connections. A client connected to this particular port will receive the data broadcast by the Master Port. A value of '0' indicates that no TCP port is defined.
INT broadcastGroupSlaveTcpBroadcastOnly	1.3.6.1.4.1.33.13.8.1.1.7	INTEGER	read-write	Specifies whether the TCP port will discard input characters for the Master port so that the Master port operates in broadcast only mode.

AddressType (1)
ADR netLoginPortLoaderAddressType	1.3.6.1.4.1.33.13.4.3.1.4	AddressType	read-only	The type of network address contained in netLoginPortLoaderAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. Corresponds indirectly to the address part of the value labeled 'Script Loaded From:' in the PORT STATUS display.
Counter (6)
CTR basicPortAsciiToTrapTranslationMessages	1.3.6.1.4.1.33.13.1.17.1.81	Counter	read-only	Count of number of trap messages sent from this port.
CTR basicPortIdleTimeouts	1.3.6.1.4.1.33.13.1.17.1.22	Counter	read-only	The number of session disconnects due to expiration of basicPortIdleTimeout. Corresponds directly to the value labeled 'Idle Timeouts:' in the PORT COUNTERS display.
CTR basicPortLogins	1.3.6.1.4.1.33.13.1.17.1.20	Counter	read-only	The number of logins on the port since system initialization. Corresponds directly to the value labeled 'Local Accesses:' in the PORT COUNTERS display.
CTR basicPortRemoteSessions	1.3.6.1.4.1.33.13.1.17.1.21	Counter	read-only	The number of remotely originating sessions to the port since system initialization. Corresponds directly to the value labeled 'Remote Accesses:' in the PORT COUNTERS display.
CTR sessionLogInCharacters	1.3.6.1.4.1.33.13.6.2.1.10	Counter	read-only	The number of characters that came into the port for the session. Corresponds directly to the value labeled 'Bytes In' in the SERVER ACCOUNTING display.
CTR sessionLogOutCharacters	1.3.6.1.4.1.33.13.6.2.1.11	Counter	read-only	The number of characters that went out of the port for the session. Corresponds directly to the value labeled 'Bytes Out' in the SERVER ACCOUNTING display.
DateTime (2)
DAT sessionLogConnectTime	1.3.6.1.4.1.33.13.6.2.1.8	DateTime	read-only	The date and time that session connection occurred. Corresponds directly to the value labeled 'Connect Time' in the SERVER ACCOUNTING display.
DAT sessionLogDisconnectTime	1.3.6.1.4.1.33.13.6.2.1.9	DateTime	read-only	The date and time that session disconnection occurred. Corresponds directly to the value labeled 'Disconnect Time' in the SERVER ACCOUNTING display.
DisplayString (53)
STR basicAlarmMasterInputName	1.3.6.1.4.1.33.13.1.36.1.4	DisplayString	read-write	The name used to identify this alarm point.
STR basicAutoProtocolDetectMessage	1.3.6.1.4.1.33.13.1.100	DisplayString	read-write	The text string sent as a prompt message out the port at the beginning of auto protocol detection mode. Corresponds to the value labeled 'APD Message' in the SERVER UNIT display.
STR basicContactClosureOrAlarmInputManufacturer	1.3.6.1.4.1.33.13.1.25.1.11	DisplayString	read-write	The name used to identify the manufacturer of this equipment.
STR basicContactClosureOrAlarmInputModel	1.3.6.1.4.1.33.13.1.25.1.12	DisplayString	read-write	The model name of this equipment.
STR basicContactClosureOrAlarmInputName	1.3.6.1.4.1.33.13.1.25.1.2	DisplayString	read-write	The name used to identify this contact closure or alarm input.
STR basicContactClosureOrAlarmInputRelatedEquipment	1.3.6.1.4.1.33.13.1.25.1.8	DisplayString	read-write	The name used to identify related equipment.
STR basicContactClosureOrAlarmInputSiteId	1.3.6.1.4.1.33.13.1.25.1.9	DisplayString	read-write	The name used to identify the site where the unit resides.
STR basicContactClosureOrAlarmInputZone	1.3.6.1.4.1.33.13.1.25.1.7	DisplayString	read-write	The name used to identify the zone where the equipment resides.
STR basicControlOutputName	1.3.6.1.4.1.33.13.1.30.1.2	DisplayString	read-write	The name used to identify this distribution control signal point.
STR basicControlOutputRelayName	1.3.6.1.4.1.33.13.1.38.1.2	DisplayString	read-write	The name used to identify this control output relay.
STR basicLoginPassword	1.3.6.1.4.1.33.13.1.7	DisplayString	read-write	The password a user must enter to be given the opportunity to log in. For security reasons, reading this object always returns a zero-length value. Corresponds directly to SERVER LOGIN PASSWORD.
STR basicLoginPrompt	1.3.6.1.4.1.33.13.1.8	DisplayString	read-write	The text string the server displays to prompt a user for the login password. Corresponds directly to SERVER LOGIN PROMPT.
STR basicPortActiveUserName	1.3.6.1.4.1.33.13.1.17.1.26	DisplayString	read-only	The user name currently logged into the port. Corresponds directly to the value by the port number and labeled 'Username' in the USERS display.
STR basicPortAlarmMasterLcdDisplayString	1.3.6.1.4.1.33.13.1.17.1.65	DisplayString	read-write	Updates the LCD display message for the high density alarm unit attached to the port. Corresponds directly to the DISPLAY AMST command.
STR basicPortAlarmMasterUpdateFirmwareFileName	1.3.6.1.4.1.33.13.1.17.1.68	DisplayString	read-write	The filename to request when downloading a new firmware image for the high density alarm unit attached to this port via TFTP. Corresponds directly to the UPDATE AMST FIRMWARE command's FILE parameter.
STR basicPortAsciiToTrapTranslationLastMessage	1.3.6.1.4.1.33.13.1.17.1.82	DisplayString	read-only	The last message or partial message sent out by this port.
STR basicPortDefaultDestLATNodeName	1.3.6.1.4.1.33.13.1.17.1.5	DisplayString	read-write	A LAT node name to use with basicPortDefaultDestName. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE NODE and the value labeled 'Node:' following the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. This object can have a non- zero-length value only if the value of basicPortDefaultDestProtocol is 'lat'.
STR basicPortDefaultDestLATPortName	1.3.6.1.4.1.33.13.1.17.1.6	DisplayString	read-write	A LAT port name to use with basicPortDefaultDestName. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE NODE and the value labeled 'Node:' following the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. this object can hav a non-zero-length value only if the value if basicPortDefaultDestProtocol is 'lat'
STR basicPortDefaultDestName	1.3.6.1.4.1.33.13.1.17.1.4	DisplayString	read-write	The default name to use in forming a connection when no other name is specified. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE and the value labeled 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display. If the value of basicPortDefaultDestProtocol is 'telnet', an Internet port number may be included on the end of the name, delimited with a colon (':'). If the value of basicPortDefaultDestProtocol is not 'telnet', then the maximum length is 16.
STR basicPortDefaultUserName	1.3.6.1.4.1.33.13.1.17.1.17	DisplayString	read-write	Default user name to use for automatically logging in the port. Corresponds directly to PORT USERNAME and the value labeled 'Port n:' in the PORT CHARACTERISTICS display.
STR basicPortLoginPassword	1.3.6.1.4.1.33.13.1.17.1.47	DisplayString	read-write	The password a user must enter to be given the opportunity to log in to a given port. For security reasons reading this object always returns a zero-length value. Corresponds directly to PORT LOGIN PASSWORD.
STR basicPortPowerMasterFirmware	1.3.6.1.4.1.33.13.1.17.1.77	DisplayString	read-only	The firmware version of the power master device, which is connected to this port.
STR basicPortPowerMasterModel	1.3.6.1.4.1.33.13.1.17.1.75	DisplayString	read-only	The model number of the power master device, which is connected to this port.
STR basicPortPowerMasterSerialNumber	1.3.6.1.4.1.33.13.1.17.1.76	DisplayString	read-only	The serial number of the power master device, which is connected to this port.
STR basicPowerMasterOutletAmperageStatus	1.3.6.1.4.1.33.13.1.37.1.5	DisplayString	read-only	Indicates the current amperage drawn at this outlet. There may be a noticeable time delay while processing a get-request for this object.
STR basicPowerMasterOutletName	1.3.6.1.4.1.33.13.1.37.1.3	DisplayString	read-write	The name used to identify this power master outlet.
STR basicPowerOutletConsoleName	1.3.6.1.4.1.33.13.1.26.1.5	DisplayString	read-write	A name used to identify a console port on a unit with power outlet managment.
STR basicPowerOutletName	1.3.6.1.4.1.33.13.1.26.1.3	DisplayString	read-write	A name used to identify this power outlet.
STR basicPrivilegedPassword	1.3.6.1.4.1.33.13.1.6	DisplayString	read-write	The password a user must enter to become privileged. For security reasons, reading this object always returns a zero-length value. Corresponds directly to SERVER PRIVILEGED PASSWORD.
STR basicSerialPortDedicatedKickStartData	1.3.6.1.4.1.33.13.1.18.1.48	DisplayString	read-write	A text string which is used to compare at login time to incoming serial data. A match will initiate a telnet session to a dedicated service. Corresponds to the value labeled 'KickStart:' in the PORT CHARACTERISTICS display.
STR basicSerialPortDedicatedUserData	1.3.6.1.4.1.33.13.1.18.1.45	DisplayString	read-write	The text string to send at the beginning of a connection to a Telnet dedicated service. Corresponds to the value labeled 'UserData:' in the PORT CHARACTERISTICS display.
STR basicSerialPortPasswordPrompt	1.3.6.1.4.1.33.13.1.18.1.43	DisplayString	read-write	The text string used to prompt for a user's password. Corresponds directly to the value labeled 'Password Prompt:' in the PORT ALTERNATE CHARACTERISTICS display.
STR basicSerialPortPrompt	1.3.6.1.4.1.33.13.1.18.1.6	DisplayString	read-write	Prompt for the system to use on the port. Corresponds directly to PORT PROMPT and the value labeled 'Prompt:' in the PORT ALTERNATE CHARACTERISTICS display.
STR basicSerialPortUsernamePrompt	1.3.6.1.4.1.33.13.1.18.1.42	DisplayString	read-write	The text string used to prompt for a user's name. Corresponds directly to the value labeled 'Username Prompt:' in the PORT ALTERNATE CHARACTERISTICS display.
STR basicWelcome	1.3.6.1.4.1.33.13.1.9	DisplayString	read-write	The text string the server displays before attempting to log in a user. Corresponds directly to SERVER WELCOME and the value labeled 'Welcome:' in the SERVER CHARACTERISTICS display.
STR cclPortCclName	1.3.6.1.4.1.33.13.7.2.1.1	DisplayString	read-write	The name of the ARAP modem CCL script file.
STR cclScriptName	1.3.6.1.4.1.33.13.7.1.1.1	DisplayString	read-only	The name of a CCL script file that has been loaded from a script server. Corresponds directly to the name in a SERVER CCL command and the value labeled 'CCL name:' in the PORT CHARACTERISTICS display.
STR menuCommand	1.3.6.1.4.1.33.13.3.4.1.4	DisplayString	read-write	The commands to execute when the user chooses the menu entry. Corresponds directly second line following the entry number in the SERVER MENU display.
STR menuContinuePrompt	1.3.6.1.4.1.33.13.3.2	DisplayString	read-write	The text to use when prompting a menu user to press RETURN to continue. Corresponds directly to SERVER MENU CONTINUE PROMPT and the value labeled 'Menu Continue Prompt:' in the SERVER MENU display.
STR menuNestedName	1.3.6.1.4.1.33.13.3.6	DisplayString	read-write	Name of the script file containing the nested menu.
STR menuSelectionPrompt	1.3.6.1.4.1.33.13.3.3	DisplayString	read-write	The text to use when prompting a menu user for a menu selection. Corresponds directly to SERVER MENU PROMPT and the value labeled 'Menu Prompt:' in the SERVER MENU display.
STR menuText	1.3.6.1.4.1.33.13.3.4.1.3	DisplayString	read-write	The text to be displayed in the menu. Corresponds directly to the line next to the entry number in the SERVER MENU display.
STR netLoginPortExecuteFile	1.3.6.1.4.1.33.13.4.3.1.7	DisplayString	read-write	The path and file name of a script to be executed immediately on the port. Corresponds directly the file name in the SCRIPT command.
STR netLoginPortLoaderFile	1.3.6.1.4.1.33.13.4.3.1.6	DisplayString	read-only	The path and file name of the script used for the current port login. Corresponds directly the file name part of the value labeled 'Script Loaded From:' in the PORT STATUS display.
STR netLoginServerName	1.3.6.1.4.1.33.13.4.2.1.1	DisplayString	read-only	The name of a network login server, suitable for resolution to a network address. Corresponds directly to host portion of SERVER SCRIPT SERVER and the value labeled 'Script Host' in the SERVER PARAMETER SERVER display.
STR netLoginServerPath	1.3.6.1.4.1.33.13.4.2.1.3	DisplayString	read-write	The full path name to the script file that is identified by the user name. Corresponds directly to path portion of SERVER SCRIPT SERVER and the value labeled 'Script Path' in the SERVER PARAMETER SERVER display. Defaults to the NULL string when a new entry is created.
STR netLoginServerSeparator	1.3.6.1.4.1.33.13.4.2.1.4	DisplayString	read-write	The single character string that will be inserted between the components of a file's path on the script server. Defaults to the NULL string when a new entry is created. Corresponds directly to the separator portion of SERVER SCRIPT SERVER display.
STR queueServiceName	1.3.6.1.4.1.33.13.2.4.1.4	DisplayString	read-only	The name of the service for which the originator is waiting. Corresponds directly to the value labeled 'Service' in the QUEUE display.
STR queueServicePortName	1.3.6.1.4.1.33.13.2.4.1.6	DisplayString	read-only	The name of the port for which the originator is waiting, if supplied by the originator. Corresponds directly to the port name part of the value labeled 'Port Name' in the SERVER QUEUE display.
STR queueSourceName	1.3.6.1.4.1.33.13.2.4.1.3	DisplayString	read-only	The name of the system that originated the queue entry. Corresponds directly to the value labeled 'Source Node' in the QUEUE display.
STR sessionLogRemoteName	1.3.6.1.4.1.33.13.6.2.1.7	DisplayString	read-only	The name of the session remote partner. Corresponds directly to the value labeled 'Destination' in the SERVER ACCOUNTING display.
STR sessionLogUserName	1.3.6.1.4.1.33.13.6.2.1.6	DisplayString	read-only	The user name logged in on the port when the event occurred. Corresponds directly to the value labeled 'Username' in the SERVER ACCOUNTING display.
STR sessionLogVerboseMessage	1.3.6.1.4.1.33.13.6.2.1.14	DisplayString	read-only	Text describing the event that was logged.
Gauge (9)
GAU basicActivePorts	1.3.6.1.4.1.33.13.1.10	Gauge	read-only	The number of ports with connected sessions or logged in users. Corresponds directly to the value labeled 'Active Ports:' and 'Cur' in the SERVER STATUS display.
GAU basicActivePortsHigh	1.3.6.1.4.1.33.13.1.11	Gauge	read-only	The highest value of basicActivePorts since system initialization. Corresponds directly to the value labeled 'Active Ports:' and 'High' in the SERVER STATUS display.
GAU basicActiveUsers	1.3.6.1.4.1.33.13.1.12	Gauge	read-only	The number of logged in users. Corresponds directly to the value labeled 'Active Users:' and 'Cur' in the SERVER STATUS display.
GAU basicActiveUsersHigh	1.3.6.1.4.1.33.13.1.13	Gauge	read-only	The highest value of basicActiveUsers since system initialization. Corresponds directly to the value labeled 'Active Users:' and 'High' in the SERVER STATUS display.
GAU basicSessions	1.3.6.1.4.1.33.13.1.14	Gauge	read-only	The total number of connected sessions. Corresponds directly to the value labeled 'Connected Sessions:' and 'Cur' in the SERVER STATUS display.
GAU basicSessionsHigh	1.3.6.1.4.1.33.13.1.15	Gauge	read-only	The highest value of basicSessions since system initialization. Corresponds directly to the value labeled 'Connected Sessions:' and 'High' in the SERVER STATUS display.
GAU menuNumber	1.3.6.1.4.1.33.13.3.1	Gauge	read-only	The number of entries in the Menu table. Corresponds indirectly to SERVER MENU display.
GAU queueHigh	1.3.6.1.4.1.33.13.2.2	Gauge	read-only	The highest value of queueNumber since system initialization. Corresponds directly to the value labeled 'Queue Entries' and 'High' in the SERVER STATUS display.
GAU queueNumber	1.3.6.1.4.1.33.13.2.3	Gauge	read-only	The number of entries in the Queue table. Corresponds directly to the value labeled 'Queue Entries' and 'Cur' in the SERVER STATUS display.
INTEGER (232)
INT basicAlarmMasterControlOutputSignal	1.3.6.1.4.1.33.13.1.36.1.6	INTEGER	read-write	Control to toggle the output signal for an alarm point.
INT basicAlarmMasterDisplay	1.3.6.1.4.1.33.13.1.36.1.13	INTEGER	read-write	Control to toggle the display of the alarm status for this point in the display window of the high density alarm unit.
INT basicAlarmMasterInputDebounceInterval	1.3.6.1.4.1.33.13.1.36.1.8	INTEGER	read-write	Amount of time in seconds to debounce a signal change before triggering an alarm.
INT basicAlarmMasterInputEnable	1.3.6.1.4.1.33.13.1.36.1.7	INTEGER	read-write	Control to toggle whether this alarm point is active.
INT basicAlarmMasterInputFaultSeverity	1.3.6.1.4.1.33.13.1.36.1.9	INTEGER	read-write	Control to determine the severity level associated with the trap sent out when a fault occurs for this alarm input point.
INT basicAlarmMasterInputFaultState	1.3.6.1.4.1.33.13.1.36.1.10	INTEGER	read-write	Control to indicate which state, open or closed, represents the fault condition for this alarm input point. The other state is the cleared condition.
INT basicAlarmMasterInputPoint	1.3.6.1.4.1.33.13.1.36.1.3	INTEGER	read-only	An index value that uniquely identifies an alarm point within an alarm slot on a high density alarm port.
INT basicAlarmMasterInputPort	1.3.6.1.4.1.33.13.1.36.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT basicAlarmMasterInputSlot	1.3.6.1.4.1.33.13.1.36.1.2	INTEGER	read-only	An index value that uniquely identifies a slot of alarm points on a given high density alarm port.
INT basicAlarmMasterInputStatus	1.3.6.1.4.1.33.13.1.36.1.11	INTEGER	read-only	Indicates the current status of the alarm input point. If the basicAlarmMasterInputValue matches the fault state, then the status is equal to the fault severity. Otherwise the status is cleared.
INT basicAlarmMasterInputTrapEnable	1.3.6.1.4.1.33.13.1.36.1.5	INTEGER	read-write	Control to send a trap when the alarm input changes state.
INT basicAlarmMasterInputValue	1.3.6.1.4.1.33.13.1.36.1.12	INTEGER	read-only	Indicates the current state of the alarm input point.
INT basicBroadcast	1.3.6.1.4.1.33.13.1.1	INTEGER	read-write	Control for user ability to broadcast messages to other local ports. Corresponds directly to SERVER BROADCAST and the presence of the label 'Broadcast' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display.
INT basicConsoleLogoutDisconnect	1.3.6.1.4.1.33.13.1.19	INTEGER	read-write	Control for automatic session disconnection when a console port user logs out. Corresponds directly to SERVER CONSOLE LOGOUT and the presence of the label 'Console Logout' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display.
INT basicContactClosureOrAlarmInputFaultSeverity	1.3.6.1.4.1.33.13.1.25.1.4	INTEGER	read-write	Control to determine the severity level associated with the trap sent out when a fault occurs for a given contact closure or alarm input.
INT basicContactClosureOrAlarmInputFaultState	1.3.6.1.4.1.33.13.1.25.1.5	INTEGER	read-write	Control to indicate which state, open or closed, represents the fault condition. The other state is the cleared condition.
INT basicContactClosureOrAlarmInputIndex	1.3.6.1.4.1.33.13.1.25.1.10	INTEGER	read-only	An index which uniquely identifies the contact closure or alarm input.
INT basicContactClosureOrAlarmInputStatus	1.3.6.1.4.1.33.13.1.25.1.6	INTEGER	read-only	Indicates the current status of the contact closure or alarm input. If the basicContactClosureOrAlarmInputValue matches the fault state, then the status is equal to the fault severity. Otherwise the status is cleared.
INT basicContactClosureOrAlarmInputTrapEnable	1.3.6.1.4.1.33.13.1.25.1.3	INTEGER	read-write	Control to send trap when contact closure or alarm input changes state.
INT basicContactClosureOrAlarmInputValue	1.3.6.1.4.1.33.13.1.25.1.1	INTEGER	read-only	Indicates the state of the contact closure or alarm input.
INT basicControlledPorts	1.3.6.1.4.1.33.13.1.20	INTEGER	read-write	Status of Controlled Ports feature. Corresponds directly to the 'Controlled Ports' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. Enabling this feature causes strings of control characters to be sent out on a port upon starting and/or stopping a session
INT basicControlOutputIndex	1.3.6.1.4.1.33.13.1.30.1.10	INTEGER	read-only	An index which uniquely identifies a distribution control signal point.
INT basicControlOutputRelayIndex	1.3.6.1.4.1.33.13.1.38.1.1	INTEGER	read-only	An index which uniquely identifies a control output relay.
INT basicControlOutputRelayState	1.3.6.1.4.1.33.13.1.38.1.3	INTEGER	read-write	Controls the opening or closing of the control output relay.
INT basicControlOutputRelayStatus	1.3.6.1.4.1.33.13.1.38.1.4	INTEGER	read-only	Indicates the current status of the control output relay.
INT basicControlOutputSignalDtrRts	1.3.6.1.4.1.33.13.1.30.1.1	INTEGER	read-write	Controls the raising or lowering of a signal on a distribution control signal point. The signal is DTR when the basicControlOutputIndex is odd, or RTS when the basicControlOutputIndex is even.
INT basicControlSignalIndex	1.3.6.1.4.1.33.13.1.28.1.10	INTEGER	read-only	An index which uniquely identifies a control signal point.
INT basicControlSignalValue	1.3.6.1.4.1.33.13.1.28.1.1	INTEGER	read-write	Sets and reads the state of the control signal point.
INT basicEnvironmentalManagerCircuitBreaker	1.3.6.1.4.1.33.13.1.24	INTEGER	read-only	Indicates whether the circuit breaker is activated.
INT basicErrorReport	1.3.6.1.4.1.33.13.1.2	INTEGER	read-write	Control for server display of an error when the user gives an unsupported command. Corresponds directly to SERVER REPORT ERRORS and the presence of the label 'Report Errors' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display.
INT basicHumidityAlarmSeverity	1.3.6.1.4.1.33.13.1.27.2.1.5	INTEGER	read-write	Control to indicate the severity level associated with the trap sent out when the humidity reading is out-of-bounds.
INT basicHumidityAlarmStatus	1.3.6.1.4.1.33.13.1.27.2.1.6	INTEGER	read-only	Indicates the current status of the humidity sensor. If the basicHumidityValue falls within the normal range, the status is cleared. Otherwise the status matches the alarm severity level.
INT basicHumiditySensor	1.3.6.1.4.1.33.13.1.27.2.1.3	INTEGER	read-write	Controls the enabling or disabling of a humidity sensor.
INT basicHumiditySensorIndex	1.3.6.1.4.1.33.13.1.27.2.1.10	INTEGER	read-only	An index which uniquely identifies a humidity sensor.
INT basicHumidityTrapHighThreshold	1.3.6.1.4.1.33.13.1.27.2.1.1	INTEGER	read-write	The humidity at or above which a sensorThresholdTrap is generated.
INT basicHumidityTrapLowThreshold	1.3.6.1.4.1.33.13.1.27.2.1.2	INTEGER	read-write	The humidity at or below which a sensorThresholdTrap is generated.
INT basicHumidityValue	1.3.6.1.4.1.33.13.1.27.2.1.4	INTEGER	read-write	The current humidity reading for this sensor.
INT basicInactivityTimer	1.3.6.1.4.1.33.13.1.4	INTEGER	read-write	Number of minutes a terminal may remain logged in with no sessions, no input or output, and no modem transitions. Corresponds directly to SERVER INACTIVITY TIMER and the value labeled 'Inactivity Timer:' in the SERVER CHARACTERISTICS display.
INT basicLock	1.3.6.1.4.1.33.13.1.3	INTEGER	read-write	Control for user ability to use a password to protect a logged in terminal from other users. Corresponds directly to SERVER LOCK and the presence of the label 'Lock' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display.
INT basicPasswordRetryLimit	1.3.6.1.4.1.33.13.1.5	INTEGER	read-write	Number of times the server allows a user to retry an incorrect password. Corresponds directly to SERVER PASSWORD LIMIT and the value labeled 'Password Limit:' in the SERVER CHARACTERISTICS display.
INT basicPortAlarmControl	1.3.6.1.4.1.33.13.1.17.1.49	INTEGER	read-write	Control to configure this port for alarm input and control output. This control is only valid on those models with variable configuration ports. This object can only be set enabled; and doing so will disable basicPortConsolePort and basicPortSensor. A set will only update the permanent database. Use a charPortReset for this change to take effect.
INT basicPortAlarmMaster	1.3.6.1.4.1.33.13.1.17.1.61	INTEGER	read-write	Control to configure this port for high densitiy alarm input and control output management. This control is only valid on those models with variable configuration ports. This object can only be set enabled; and doing so will disable basicPortConsolePort, basicPortSensor and basicPortAlarmControl. A set will only update the permanent database. Use a charPortReset for this change to take effect.
INT basicPortAlarmMasterAccounting	1.3.6.1.4.1.33.13.1.17.1.62	INTEGER	read-write	Control to toggle logging of alarm events on this port. Use a charPortReset for this change to take effect.
INT basicPortAlarmMasterAudibleAlarm	1.3.6.1.4.1.33.13.1.17.1.63	INTEGER	read-write	Control whether the alarm will have an audible sound for all alarm points attached to this port.
INT basicPortAlarmMasterFaultSeverity	1.3.6.1.4.1.33.13.1.17.1.71	INTEGER	read-write	Control to determine the severity level associated with the trap sent out when a fault occurs when no response is obtained from the high density alarm unit attached to this port.
INT basicPortAlarmMasterFixTime	1.3.6.1.4.1.33.13.1.17.1.64	INTEGER	read-write	Time in minutes between audible alarm soundings for an alarm master port. This occurs after someone hits the master alarm reset button. If there is at least one alarm condition on an alarm point within the fix time, then the alarm will sound again at the end of that fix time.
INT basicPortAlarmMasterReboot	1.3.6.1.4.1.33.13.1.17.1.66	INTEGER	read-write	Control to reboot the high density alarm unit attached to the port when set to 'execute'. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Corresponds directly to the REBOOT AMST command.
INT basicPortAlarmMasterStatus	1.3.6.1.4.1.33.13.1.17.1.70	INTEGER	read-only	Indicates the current status of the high density alarm unit attached to the port. If no response is obtained from this unit, the status is set to basicPortAlarmMasterFaultSeverity. Otherwise it is cleared.
INT basicPortAlarmMasterUpdateFirmware	1.3.6.1.4.1.33.13.1.17.1.69	INTEGER	read-write	Control to update firmware for the high density alarm unit attached to the port when set to 'execute'. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. The basicPortAlarmMasterUpdateFirmwareHost and basicPortAlarmMasterUpdateFirmwareFileName must be set prior to setting this object. Corresponds directly to the UPDATE AMST FIRMWARE command.
INT basicPortAsciiToTrapTranslation	1.3.6.1.4.1.33.13.1.17.1.79	INTEGER	read-write	Control to configure the port as an ascii-to-trap translator. One must log out the port for this change to take effect.
INT basicPortAsciiToTrapTranslationTrapSeverity	1.3.6.1.4.1.33.13.1.17.1.80	INTEGER	read-write	Control to determine the severity level associated with the trap sent out from this port. One must log out the port for this change to take effect.
INT basicPortAutoConnect	1.3.6.1.4.1.33.13.1.17.1.7	INTEGER	read-write	Control for automatic session connection. Corresponds directly to PORT AUTOCONNECT and the presence of the label 'Autoconnect' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortAutoLogin	1.3.6.1.4.1.33.13.1.17.1.8	INTEGER	read-write	Control for automatic port login. Corresponds directly to PORT AUTODEDICATED and the presence of the label 'Autodedicated' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortBroadcast	1.3.6.1.4.1.33.13.1.17.1.9	INTEGER	read-write	Control for display of messages sent by users on other ports. Corresponds directly to PORT BROADCAST and the presence of the label 'Broadcast' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortCommandLogging	1.3.6.1.4.1.33.13.1.17.1.50	INTEGER	read-write	A control to toggle logging of commands at this port. Command input may be logged from direct terminal connections, session input from the LAN, or session output to the LAN. Corresponds directly to the presence of 'Command Logging' under the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. The desired change will not take effect until the port is logged off.
INT basicPortCommandLoggingSuppressControlCharacters	1.3.6.1.4.1.33.13.1.17.1.56	INTEGER	read-write	Control to toggle suppression of control characters in the command log. This object can only be set to enabled when command logging is enabled on that port.
INT basicPortConnectResume	1.3.6.1.4.1.33.13.1.17.1.10	INTEGER	read-write	Control for behavior of a connection attempt to a destination where the port already has a connection. 'disabled' causes a new connection. 'enabled' causes the existing connection to become the active connection. Corresponds directly to PORT CONNECTRESUME and the presence of the label 'Connectresume' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortConsolePort	1.3.6.1.4.1.33.13.1.17.1.46	INTEGER	read-write	Control to configure this port as a console port. This control is only valid on those models with variable configuration ports. This object can only be set enabled; and doing so will disable basicPortSensor and basicPortAlarmControl. A set will only update the permanent database. Use a charPortReset for this change to take effect.
INT basicPortDataLogging	1.3.6.1.4.1.33.13.1.17.1.57	INTEGER	read-write	Control to toggle data logging on the specified port.
INT basicPortDataLoggingSuppressControlCharacters	1.3.6.1.4.1.33.13.1.17.1.58	INTEGER	read-write	Control to toggle suppression of control characters in the data log. This object can only be set to enabled when data logging is enabled on that port.
INT basicPortDefaultDestAction	1.3.6.1.4.1.33.13.1.17.1.2	INTEGER	read-write	The action to take relative to basicPortDefaultDestName. Corresponds directly to PORT DEDICATED/PREFERRED SERVICE and the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display.
INT basicPortDefaultDestControlled	1.3.6.1.4.1.33.13.1.17.1.33	INTEGER	read-write	A control to send preconfigured controlled port session strings when entering or exiting a session established to the basicPortDefaultDestName. Corresponds directly to the value labeled '(Controlled)' following the label 'Dedicated/Preferred Service:' in the PORT CHARACTERISTICS display.
INT basicPortDefaultDestProtocol	1.3.6.1.4.1.33.13.1.17.1.3	INTEGER	read-write	The session protocol to use with basicPortDefaultDestName. Corresponds directly to LAT/TELNET PORT DEDICATED/PREFERRED SERVICE.
INT basicPortDefaultProtocol	1.3.6.1.4.1.33.13.1.17.1.19	INTEGER	read-write	The session protocol to use when not otherwise specified. Corresponds directly to PORT RESOLVE SERVICE and the value labeled 'Resolve Service:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicPortDefaultSessionMode	1.3.6.1.4.1.33.13.1.17.1.27	INTEGER	read-write	Data recognition mode when starting a session, with the following meanings: interactive locally recognize all controls binary recognize only session protocol (corresponds to PASSALL) binaryWithFlow recognize only XON and XOFF (corresponds to PASTHRU transparent recognize no data Corresponds directly to PORT DEFAULT SESSION MODE and the value labeled 'Default Session Mode:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicPortDialup	1.3.6.1.4.1.33.13.1.17.1.11	INTEGER	read-write	Defines whether the port should be considered as connected to a dialup line. 'enabled' means that it is. Corresponds directly to PORT DIALUP and the presence of the label 'Dial Up' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicPortFallBack	1.3.6.1.4.1.33.13.1.17.1.60	INTEGER	read-write	Control to allow a 'fallback' authentication mechanism after RADIUS or SecurID authentication fails because the RADIUS or SecurID servers are unavailable. Onboard security, an internal security database, is used for fallback authentication. The user in fallback mode must enter a valid username and password to be successfully logged in. The change takes effect after logging out the port.
INT basicPortFallThrough	1.3.6.1.4.1.33.13.1.17.1.55	INTEGER	read-write	Control to allow a user to login to a port after RADIUS or SecurID authentication fails because the RADIUS servers or SecurID servers are unavailable. When a user is logged in via 'fallthrough', he is logged in to the port as a non-privileged user. The change takes effect after logging out the port.
INT basicPortIdleTimeout	1.3.6.1.4.1.33.13.1.17.1.12	INTEGER	read-write	The number of minutes the system will allow a session to have no activity before automatically disconnecting it. A value of -1 indicates no timeout. Zero is not a valid value. Corresponds directly to PORT IDLE TIMEOUT and the value labeled 'Idle Timeout:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicPortIdleTimeReceive	1.3.6.1.4.1.33.13.1.17.1.43	INTEGER	read-write	Control to restrict the basicPortIdleTimeout to apply to data received from the network and transmitted out the serial port. Data received by the serial port will not be considered activity. Corresponds directly to the value labeled 'Idle Time Receive Mode:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicPortIdleTimeTransmit	1.3.6.1.4.1.33.13.1.17.1.44	INTEGER	read-write	Control to restrict the basicPortIdleTimeout to apply to data received from the serial port and transmitted out the LAN. Data received from the network will not count as activity. Corresponds directly to the value labeled 'Idle Time Transmit Mode:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicPortInactivityLogout	1.3.6.1.4.1.33.13.1.17.1.13	INTEGER	read-write	Control for the system automatically logging the port out when it has no sessions, no local activity, and no modem signal changes for the time period specified by basicInactivityTimer. Corresponds directly to PORT INACTIVITY LOGOUT and the presence of the label 'Inactivity Logout' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortIndex	1.3.6.1.4.1.33.13.1.17.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT basicPortLastInCharacter	1.3.6.1.4.1.33.13.1.17.1.24	INTEGER	read-only	The character that most recently came into the port. Corresponds directly to the value labeled 'Last Char Input:' in the PORT STATUS display.
INT basicPortLastOutCharacter	1.3.6.1.4.1.33.13.1.17.1.25	INTEGER	read-only	The character that most recently went out of the port. Corresponds directly to the value labeled 'Last Char Output:' in the PORT STATUS display.
INT basicPortLockout	1.3.6.1.4.1.33.13.1.17.1.78	INTEGER	read-write	Control to prohibit access to this port and send a trap when login authentication fails. One must log out the port for this change to take effect.
INT basicPortLoginDuration	1.3.6.1.4.1.33.13.1.17.1.39	INTEGER	read-write	The amount of time in minutes that a port may remain logged in regardless of the activity on the port. The value 0 indicates that the timer is disabled. Corresponds directly to the value labeled 'Login Duration:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicPortLossNotification	1.3.6.1.4.1.33.13.1.17.1.14	INTEGER	read-write	Control for the system sending a Bell character to the port when it looses an input character due to an overrun or data error. Corresponds directly to PORT LOSS NOTIFICATION and the presence of the label 'Loss Notification' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortMessageCodes	1.3.6.1.4.1.33.13.1.17.1.15	INTEGER	read-write	Control for including error numbers in error messages displayed on the port. Corresponds directly to PORT MESSAGE CODES and the presence of the label 'Message Codes' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortMultisessions	1.3.6.1.4.1.33.13.1.17.1.16	INTEGER	read-write	Control for running the multisession line protocol between the port and the locally-connected terminal. Corresponds directly to PORT MULTISESSIONS and the presence of the label 'Multisessions' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortOnboardSecurity	1.3.6.1.4.1.33.13.1.17.1.59	INTEGER	read-write	A control to toggle onboard security for this port where the username and password are authenticated against an internal access list. The desired change will not take effect until the port is logged off.
INT basicPortOutboundSecurity	1.3.6.1.4.1.33.13.1.17.1.40	INTEGER	read-write	Control to disable outbound security, which can be either Kerberos or SecureID, on a per port basis. Corresponds directly to the presence of the value 'OutboundSecurity' following the label 'Enabled Characteristics' in the PORT CHARACTERISTICS display.
INT basicPortPortIndex	1.3.6.1.4.1.33.13.1.21.1.1	INTEGER	read-only	The value of basicPortIndex for the port to which this session belongs. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT basicPortPowerMaster	1.3.6.1.4.1.33.13.1.17.1.72	INTEGER	read-write	Control to configure this port as a power master port. This control is only valid on those models with variable configuration ports and which support the power master. This object can only be set enabled, and doing so will disable the previous port type, such as basicPortConsolePort. A set will only update the permanent database. Use a charPortReset for this change to take effect.
INT basicPortPowerMasterAlarmSeverity	1.3.6.1.4.1.33.13.1.17.1.83	INTEGER	read-write	Control to determine the severity level associated with the trap sent out when the power device is not responding to this port.
INT basicPortPowerMasterDeviceStatus	1.3.6.1.4.1.33.13.1.17.1.84	INTEGER	read-only	Indicates the current status of the power device controlled by this port. If the device is responding, the status is cleared. Otherwise the status matches the basicPortPowerMasterAlarmSeverity.
INT basicPortPowerMasterSwitch	1.3.6.1.4.1.33.13.1.17.1.74	INTEGER	read-write	Control to power on or off all of the outlets in the power device attached to this port. A get-request always returns ready.
INT basicPortPowerMasterTimeDelay	1.3.6.1.4.1.33.13.1.17.1.73	INTEGER	read-write	Control to set the power up delay interval in milliseconds for the power device attached to this port.
INT basicPortRemoteDisconnectNotify	1.3.6.1.4.1.33.13.1.17.1.32	INTEGER	read-write	If enabled, a BELL (ctrl G) will be sent out the serial port when a remote session is disconnected and the port is logged out.
INT basicPortRloginTransparentMode	1.3.6.1.4.1.33.13.1.17.1.38	INTEGER	read-write	A control to pass x'ff' as binary data, not doubling x'ff'. Similar to basicPortSessionMode = transparent but for a rlogin session.
INT basicPortSensor	1.3.6.1.4.1.33.13.1.17.1.48	INTEGER	read-write	Control to configure this port as a temperature and humidity sensor. This control is only valid on those models with variable configuration ports. This object can only be set enabled; and doing so will disable basicPortConsolePort and basicPortAlarmControl. A set will only update the permanent database. Use a charPortReset for this change to take effect.
INT basicPortSessEncryption	1.3.6.1.4.1.33.13.1.22	INTEGER	read-write	Status of the default encryption value to be set for each session. Corresponds directly to Console Security on SHOW SERVER screen.
INT basicPortSessIndex	1.3.6.1.4.1.33.13.1.21.1.2	INTEGER	read-only	The session index in the context of the port, a non-zero positive integer. Session indexes within a port need not be sequential. Session indexes may be reused for different ports. For example, port 1 and port 3 may both have a session 2 at the same time. Session indexes may have any valid integer value, with any meaning convenient to the agent implementation. The session identified by a particular value of this index is the same session as identified by charSessIndex in the standard Character MIB.
INT basicPortSessionMode	1.3.6.1.4.1.33.13.1.17.1.31	INTEGER	read-write	Data recognition mode for an active session, with the following meanings: interactive locally recognize all controls binary recognize only session protocol (corresponds to PASSALL) binaryWithFlow recognize only XON and XOFF (corresponds to PASTHRU transparent recognize no data noActiveSessions no sessions on this port. This object can be set to values of 1 to 4, but only if there is an active session on the port.
INT basicPortSignalName	1.3.6.1.4.1.33.13.1.35.1.2	INTEGER	read-only	Identification of the hardware signal as specified in RFC1659 as follows: rts Request to Send cts Clear to Send dsr Data Set Ready dts Data Terminal Ready ri Ring Indicator dcd Received Line Signal Detector Some agents do not support DSR since its pin is shared with DCD.
INT basicPortStatus	1.3.6.1.4.1.33.13.1.17.1.23	INTEGER	read-only	The current operational status of the port. Corresponds directly to the value labeled 'Status:' in the PORT STATUS display.
INT basicPortTl1Console	1.3.6.1.4.1.33.13.1.17.1.54	INTEGER	read-write	Controls whether this port becomes the TL1 console receiving and displaying autonomous reports of alarm events. A change takes effect after logging out the port.
INT basicPortTl1Mode	1.3.6.1.4.1.33.13.1.17.1.53	INTEGER	read-write	Controls the TL1 mode of a port. Valid TL1 modes are human- to-machine language (hml), machine-to-machine language (mml), and MML without echo. MML is for direct connection to another TL1 device whereas HML provides human prompts. A change takes effect after logging out the port.
INT basicPortTrapIndex	1.3.6.1.4.1.33.13.1.35.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by rs232PortIndex in the standard rs232 MIB.
INT basicPortTrapStatus	1.3.6.1.4.1.33.13.1.35.1.3	INTEGER	read-write	Control to toggle the sending of a trap on a specific signal change on a physical port. One must logout the port prior to this taking effect.
INT basicPortUnixCommands	1.3.6.1.4.1.33.13.1.17.1.30	INTEGER	read-write	Control to allow the user to use Unix-style commands the port.
INT basicPortVerification	1.3.6.1.4.1.33.13.1.17.1.18	INTEGER	read-write	Control for display of informational messages on the port when the user connects, disconnects, or switches a session. Corresponds directly to PORT VERIFICATION and the presence of the label 'Verification' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicPortXonTimer	1.3.6.1.4.1.33.13.1.17.1.41	INTEGER	read-write	Indicates the number of seconds between successive 'XON's sent out a port. A zero signifies that the timer is disabled. Corresponds directly to the value labeled 'Xon Send Timer:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicPortZero	1.3.6.1.4.1.33.13.1.17.1.28	INTEGER	read-write	Control to zero counters for the port. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes the port's counters to be zeroed. Corresponds to the ZERO PORT command.
INT basicPortZeroDisconnectSession	1.3.6.1.4.1.33.13.1.17.1.45	INTEGER	read-write	A control to disconnect a session at Port 0 when the password limit is reached.
INT basicPowerAlarmTimer	1.3.6.1.4.1.33.13.1.29	INTEGER	read-write	The polling interval in seconds for the fuse and power supply status. An alarm trap is issued on power failure.
INT basicPowerMasterOutletIndex	1.3.6.1.4.1.33.13.1.37.1.2	INTEGER	read-only	An index which uniquely identifies a power master outlet.
INT basicPowerMasterOutletState	1.3.6.1.4.1.33.13.1.37.1.4	INTEGER	read-write	Switches the power master outlet on or off. There may be a noticeable time delay while processing a get-request for this object.
INT basicPowerMasterPortIndex	1.3.6.1.4.1.33.13.1.37.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by the charPortIndex in the standard Character MIB.
INT basicPowerOutletHighCurrent	1.3.6.1.4.1.33.13.1.26.1.6	INTEGER	read-write	A control to indicate a high current unit is attached to this power outlet. When enabled the high current unit will provide current when it detects no power from the power outlet; and will stop the current when the outlet resumes power. This control only works on those InReach devices which support the high current unit such as the IRMGR0. Corresponds directly to the value labeled 'HCNC Setting' in the INREACH MANAGER OUTLET STATUS display.
INT basicPowerOutletIndex	1.3.6.1.4.1.33.13.1.26.1.10	INTEGER	read-only	An index which uniquely identifies a power outlet.
INT basicPowerOutletOnOff	1.3.6.1.4.1.33.13.1.26.1.1	INTEGER	read-write	Controls turning on or off the power for the device connected to this power outlet.
INT basicPowerOutletReboot	1.3.6.1.4.1.33.13.1.26.1.2	INTEGER	read-write	Controls rebooting of the device attached this power outlet.
INT basicPowerOutletRedundant	1.3.6.1.4.1.33.13.1.26.1.4	INTEGER	read-only	Controls whether power outlets in bank A have redundant outlets in bank B. When enabled, powering on an outlet in bank A will simultaneously power on the corresponding outlet number in bank B.
INT basicPowerStatusFuseA	1.3.6.1.4.1.33.13.1.31	INTEGER	read-only	Indicates the status of fuse bank A.
INT basicPowerStatusFuseB	1.3.6.1.4.1.33.13.1.32	INTEGER	read-only	Indicates the status of fuse bank B.
INT basicPowerSupplyStatusA	1.3.6.1.4.1.33.13.1.33	INTEGER	read-only	Indicates the status of power supply A.
INT basicPowerSupplyStatusB	1.3.6.1.4.1.33.13.1.34	INTEGER	read-only	Indicates the status of power supply B.
INT basicSerialPortAPDTimeout	1.3.6.1.4.1.33.13.1.18.1.36	INTEGER	read-write	A time value, in seconds, that specifies how long the port will attempt to determine which protocol is coming into the port. When basicSerialPortAPDTimeout seconds have expired, the port will assume the protocol to use is that specified by basicSerialPortAPDDefaultProtocol. A value of 0 (zero provides an unlimited timeout.
INT basicSerialPortAutoHangup	1.3.6.1.4.1.33.13.1.18.1.39	INTEGER	read-write	A control that, if enabled, will cause the port to be logged off when the last session on that port is destroyed
INT basicSerialPortAutoProtocolDetectPrompt	1.3.6.1.4.1.33.13.1.18.1.41	INTEGER	read-write	Controls whether to send the basicAutoProtocolDetectMessage out the serial port at the beginning of auto protocol detection mode. Corresponds to the value labeled 'APD Prompt' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortAutoProtocolDetectSecurityInteractiveOnly	1.3.6.1.4.1.33.13.1.18.1.44	INTEGER	read-write	Controls whether Auto Protocol Detect (APD) authentication applies only to interactive users, and not to other APD protocols such as PPP. Corresponds directly to the value labeled 'APD Authentication Interactive Only:' in the PORT CHARACTERISTICS display.
INT basicSerialPortBackwardSwitch	1.3.6.1.4.1.33.13.1.18.1.9	INTEGER	read-write	Character input from the character port to cause a switch to the previous, lower numbered session. The value 0 indicates no character has this effect. Corresponds directly to PORT BACKWARD SWITCH and the value labeled 'Backwards Switch:' in the PORT CHARACTERISTICS display.
INT basicSerialPortBreak	1.3.6.1.4.1.33.13.1.18.1.2	INTEGER	read-write	Action to take on a BREAK condition from the port. Corresponds directly to PORT BREAK and the value labeled 'Break:' in the PORT CHARACTERISTICS display.
INT basicSerialPortBreakLength	1.3.6.1.4.1.33.13.1.18.1.50	INTEGER	read-write	Specifies the duration in milliseconds of a remote serial break which is sent via the Telnet Break command. Corresponds directly to the value labeled 'Break Length:' in the PORT CHARACTERISTIC display.
INT basicSerialPortCommandSize	1.3.6.1.4.1.33.13.1.18.1.40	INTEGER	read-write	Maximum number of input characters to hold in the command buffer. Corresponds directly to the PORT COMMAND SIZE and the value labeled 'Command Size:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortDCDTimeout	1.3.6.1.4.1.33.13.1.18.1.16	INTEGER	read-write	The number of milleseconds that DCD may be asserted before disconnecting the port. Corresponds directly to PORT DCD TIMEOUT and the value labeled 'DCD Timeout:' in the PORT ALTERNATE CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortDSRLogout	1.3.6.1.4.1.33.13.1.18.1.14	INTEGER	read-write	Control for logging out the port when DCD is deasserted. Corresponds directly to PORT DSRLOGOUT and the presence of the label 'DSRlogout' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortDSRObserve	1.3.6.1.4.1.33.13.1.18.1.15	INTEGER	read-write	Control for beginning the login sequence on the port when DCD is asserted. Corresponds directly to PORT DSRWAIT and the presence of the label 'DSRwait' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortDTRAssert	1.3.6.1.4.1.33.13.1.18.1.17	INTEGER	read-write	Control when the system asserts DTR on the port. always unconditional(DISABLED) onConnectionOrRing connection formed or RING asserted(ENABLED) onConnection connection formed (FORCONNECTION) onRing RING asserted (FORRING) Corresponds directly to PORT DTRWAIT and the value labeled 'DTR Wait:' in the PORT ALTERNATE CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortForwardSwitch	1.3.6.1.4.1.33.13.1.18.1.10	INTEGER	read-write	Character input from the character port to cause a switch to the next, higher numbered session. The value 0 indicates no character has this effect. Corresponds directly to PORT FORWARD SWITCH and the value labeled 'Forwards Switch:' in the PORT CHARACTERISTICS display.
INT basicSerialPortGatewayAutoDiscovery	1.3.6.1.4.1.33.13.1.18.1.53	INTEGER	read-write	Control to enable a non-standard method of acquiring the gateway address after boot completes via the bootp protocol.
INT basicSerialPortIndex	1.3.6.1.4.1.33.13.1.18.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT basicSerialPortInterrupts	1.3.6.1.4.1.33.13.1.18.1.3	INTEGER	read-write	Control for recognizing BREAK or local switch to interrupt a session. Corresponds directly to PORT INTERRUPTS and the presence of the label 'Interrupts' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicSerialPortIpAutoDiscovery	1.3.6.1.4.1.33.13.1.18.1.47	INTEGER	read-write	Control to enable a non-standard method of acquiring the IP address after boot completes via the BOOTP protocol. Corresponds to the value labeled 'IP Address Auto Discovery' in the SERVER CHARACTERISTICS display.
INT basicSerialPortIpConfigureBootp	1.3.6.1.4.1.33.13.1.18.1.57	INTEGER	read-write	Control to use the BOOTP protocol upon startup to learn the unit's own internet address, subnet mask, primary and secondary gateway servers, domain name servers, time server and domain name. This object was moved to the ITOUCH-INTERNET-MIB for InReach agent software version V2.4.
INT basicSerialPortLimitedCommands	1.3.6.1.4.1.33.13.1.18.1.18	INTEGER	read-write	Control for limiting the commands available to the user on the port. Corresponds directly to PORT SECURITY and the presence of the label 'Security' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortLimitedView	1.3.6.1.4.1.33.13.1.18.1.19	INTEGER	read-write	Control for restricting what a user may display. Corresponds directly to PORT LIMITED VIEW and the presence of the label 'Limited View' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicSerialPortLineEditor	1.3.6.1.4.1.33.13.1.18.1.21	INTEGER	read-write	Control for allowing the user to use local mode command line editing. Corresponds directly to PORT LINE EDITOR and the presence of the label 'Line Editor' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicSerialPortLineEditorBackspace	1.3.6.1.4.1.33.13.1.18.1.22	INTEGER	read-write	Character input from the character port to move the cursor to the left. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR BACKSPACE and the value labeled 'Backspace Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorBeginning	1.3.6.1.4.1.33.13.1.18.1.23	INTEGER	read-write	Character input from the character port to move the cursor to the beginning of the line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR BEGINNING and the value labeled 'Begin Line Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorCancel	1.3.6.1.4.1.33.13.1.18.1.24	INTEGER	read-write	Character input from the character port to cancel an interactive dialog or delete the current line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR CANCEL and the value labeled 'Cancel Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorDeleteBeginning	1.3.6.1.4.1.33.13.1.18.1.25	INTEGER	read-write	Character input from the character port to delete the current line from the cursor to the beginning. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR DELETE BEGINNING and the value labeled 'Delete Begin Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorDeleteLine	1.3.6.1.4.1.33.13.1.18.1.26	INTEGER	read-write	Character input from the character port to delete the current line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR DELETE LINE and the value labeled 'Delete Line Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorEnd	1.3.6.1.4.1.33.13.1.18.1.27	INTEGER	read-write	Character input from the character port to move the cursor to the end of the line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR END and the value labeled 'End of Line Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorForward	1.3.6.1.4.1.33.13.1.18.1.28	INTEGER	read-write	Character input from the character port to move the cursor to the right. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR FORWARDS and the value labeled 'Forwards Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorInsertToggle	1.3.6.1.4.1.33.13.1.18.1.29	INTEGER	read-write	Character input from the character port to toggle between insert and overwrite modes. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR INSERT TOGGLE and the value labeled 'Insert Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorNextLine	1.3.6.1.4.1.33.13.1.18.1.30	INTEGER	read-write	Character input from the character port to recall the next, newer line in the command history. The value -1 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR NEXT LINE and the value labeled 'Next Line Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorPreviousLine	1.3.6.1.4.1.33.13.1.18.1.31	INTEGER	read-write	Character input from the character port to recall the previous, older line in the command history. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR PREVIOUS LINE and the value labeled 'Previous Line Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorQuotingCharacter	1.3.6.1.4.1.33.13.1.18.1.32	INTEGER	read-write	Character input from the character port to inhibit interpretation of the next input character. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR QUOTING CHARACTER and the value labeled 'Quoting Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLineEditorRedisplay	1.3.6.1.4.1.33.13.1.18.1.33	INTEGER	read-write	Character input from the character port to redisplay the current command line. The value 0 indicates no character has this effect. Corresponds directly to PORT LINE EDITOR REDISPLAY CHARACTER and the value labeled 'Redisplay Character:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortLocalSwitch	1.3.6.1.4.1.33.13.1.18.1.11	INTEGER	read-write	Character input from the character port to cause a switch to local command mode. The value 0 indicates no character has this effect. Corresponds directly to PORT LOCAL SWITCH and the value labeled 'Local Switch:' in the PORT CHARACTERISTICS display.
INT basicSerialPortModemControl	1.3.6.1.4.1.33.13.1.18.1.12	INTEGER	read-write	Control for observing hardware modem control signals. Corresponds directly to PORT MODEM CONTROL and the value labeled 'Modem Control:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortNoLoss	1.3.6.1.4.1.33.13.1.18.1.4	INTEGER	read-write	Control for storing port input locally in anticipation of session startup. Corresponds directly to PORT NOLOSS and the presence of the label 'Noloss' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicSerialPortPassword	1.3.6.1.4.1.33.13.1.18.1.20	INTEGER	read-write	Control for requiring the user to supply the login password to log in on the port. Corresponds directly to PORT PASSWORD and the presence of the label 'Password' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicSerialPortPause	1.3.6.1.4.1.33.13.1.18.1.5	INTEGER	read-write	Control for pausing after each screenful of locally-originated output to the port. Corresponds directly to PORT PAUSE and the presence of the label 'Pause' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT basicSerialPortQuadartReceiveDiscard	1.3.6.1.4.1.33.13.1.18.1.34	INTEGER	read-write	Control for discard of received errors from quadart hardware.
INT basicSerialPortRaiseControlDtr	1.3.6.1.4.1.33.13.1.18.1.56	INTEGER	read-write	Controls the ability to change the state of DTR using basicSerialPortRaiseLowerDTR. This characteristic is not intended for use with modem ports. Corresponds directly to the presence of 'Control DTR' under the label 'Enabled Characteristics' in the PORT CHARACTERISTICS display. The desired change will not take effect until the port is logged off.
INT basicSerialPortRaiseLowerDtr	1.3.6.1.4.1.33.13.1.18.1.55	INTEGER	read-write	A control to to raise or lower the DTR signal from this port by setting it to high or low, respectively. This request will have no effect unless basicSerialPortRaiseControlDtr is enabled. In response to a get-request or get-next-request the agent always returns low for this object.
INT basicSerialPortRotaryRoundRobin	1.3.6.1.4.1.33.13.1.18.1.51	INTEGER	read-write	Controls whether a port which participates in an internet rotary is selected in round robin or fixed priority order. Corresponds directly to the value labeled 'Round Robin search:' in the SERVER INTERNET ROTARY display.
INT basicSerialPortSignalCheck	1.3.6.1.4.1.33.13.1.18.1.13	INTEGER	read-write	Control for observing DSR and DCD to bound allowing sessions. Corresponds directly to PORT SIGNAL CHECK and the presence of the label 'Signal Check' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. This object is not available on units that do not support modem signals (ie 2220).
INT basicSerialPortSubnetAutoDiscovery	1.3.6.1.4.1.33.13.1.18.1.54	INTEGER	read-write	Control to enable a non-standard method of acquiring the subnet mask after boot completes via the bootp protocol.
INT basicSerialPortTerminalType	1.3.6.1.4.1.33.13.1.18.1.7	INTEGER	read-write	Type of terminal attached to the port, for formatting local output. Corresponds directly to PORT TYPE and the value labeled 'Type:' in the PORT CHARACTERISTICS display.
INT basicSerialPortTypeaheadLimit	1.3.6.1.4.1.33.13.1.18.1.8	INTEGER	read-write	Maximum number of input characters to hold pending tranmission on a session. Corresponds directly to PORT TYPEAHEAD SIZE and the value labeled 'Typeahead Size:' in the PORT ALTERNATE CHARACTERISTICS display.
INT basicSerialPortUsernameCharSet	1.3.6.1.4.1.33.13.1.18.1.38	INTEGER	read-write	A control, that if set to seven-bit, will allow only the ASCII printable characters in the range SP (X20) to ~ (X7E) in the username field. A value of none allows any character
INT basicSerialPortWelcomeBeforeAuthentication	1.3.6.1.4.1.33.13.1.18.1.52	INTEGER	read-write	Control to display the basicWelcome message prior to authenticating the user. Corresponds to the presence of the value 'Welcome-Banner-Pre-Authentication' following the label 'Enabled Characteristics' in the PORT CHARACTERISTICS display.
INT basicSessControlled	1.3.6.1.4.1.33.13.1.21.1.3	INTEGER	read-only	A control to send preconfigured controlled port session strings out the serial port when entering or exiting this session. Corresponds directly to the value labeled 'Controlled' under the Service Mode header in the SESSION display.
INT basicSessionsLimit	1.3.6.1.4.1.33.13.1.16	INTEGER	read-write	The maximum total number of sessions that can simultaneously be connected to the system. A value of -1 indicates no limit up to available dynamic system memory. Corresponds directly to SERVER SESSION LIMIT and the value labeled 'Connected Sessions:' and 'Max' in the SERVER STATUS display.
INT basicTemperatureAlarmSeverity	1.3.6.1.4.1.33.13.1.27.1.1.5	INTEGER	read-write	Control to determine the severity level associated with the trap sent out when the temperature reading is out-of-bounds.
INT basicTemperatureAlarmStatus	1.3.6.1.4.1.33.13.1.27.1.1.6	INTEGER	read-only	Indicates the current status of the temperature sensor. If the basicTemperatureValue falls within the normal range, the status is cleared. Otherwise the status matches the alarm severity level.
INT basicTemperatureSensor	1.3.6.1.4.1.33.13.1.27.1.1.3	INTEGER	read-write	Controls the enabling or disabling of a temperature sensor.
INT basicTemperatureSensorIndex	1.3.6.1.4.1.33.13.1.27.1.1.10	INTEGER	read-only	An index which uniquely identifies a temperature sensor.
INT basicTemperatureUnits	1.3.6.1.4.1.33.13.1.23	INTEGER	read-write	Indicates the units of measurement for the temperature sensors.
INT basicTemperatureValue	1.3.6.1.4.1.33.13.1.27.1.1.4	INTEGER	read-write	The current temperature reading for this sensor.
INT basicTempTrapHighThreshold	1.3.6.1.4.1.33.13.1.27.1.1.1	INTEGER	read-write	The temperature at or above which a sensorThresholdTrap is generated.
INT basicTempTrapLowThreshold	1.3.6.1.4.1.33.13.1.27.1.1.2	INTEGER	read-write	The temperature at or below which a sensorThresholdTrap is generated.
INT broadcastGroupIndex	1.3.6.1.4.1.33.13.8.1.1.1	INTEGER	read-only	An index value that uniquely identifies a broadcast group.
INT broadcastGroupMaster	1.3.6.1.4.1.33.13.8.1.1.3	INTEGER	read-write	An index value that uniquely identifies the Master Broadcast Port for this group. The port provided in this object is the same port as identified by charPortIndex in the standard Character MIB.
INT broadcastGroupSlaveTcpBroadcastOnly	1.3.6.1.4.1.33.13.8.1.1.7	INTEGER	read-write	Specifies whether the TCP port will discard input characters for the Master port so that the Master port operates in broadcast only mode.
INT broadcastGroupSlaveTcpPort	1.3.6.1.4.1.33.13.8.1.1.6	INTEGER	read-write	A TCP port number on which the broadcast group process will listen for incoming TCP connections. A client connected to this particular port will receive the data broadcast by the Master Port. A value of '0' indicates that no TCP port is defined.
INT broadcastGroupStatus	1.3.6.1.4.1.33.13.8.1.1.2	INTEGER	read-write	A status value for the broadcast group. The value 'enabled' means that the group is active and broadcasting data whereas 'disabled' means that the group is not active.
INT cclPortModemAudible	1.3.6.1.4.1.33.13.7.2.1.2	INTEGER	read-write	This boolean indicates if the CCL script should put the modem into audible mode.
INT cclScriptControl	1.3.6.1.4.1.33.13.7.1.1.2	INTEGER	read-write	Control for maintaining the CCL script. The refresh action consists of retrieving the script by name from a script server and parsing it into an executable format. This may be used to add an entry to the table or refresh an existing entry with a new version of the CCL script from the server. This command may take ten seconds or more to complete and may fail if the script file cannot be retrieved or an error is encountered in parsing the CCL script. An error value of genErr is returned upon refresh failure. The refresh action corresponds directly to the commnd: REFRESH SERVER CCL. Setting this field to delete causes a script that is NOT being referenced by any ports to be removed from the list and its memory freed. This action corresponds directly to the command: DELETE SERVER CCL. An error value of badValue is returned upon delete failure.
INT dialPortDialback	1.3.6.1.4.1.33.13.5.1.1.2	INTEGER	read-write	Control for use of dialback when a user logs in on the port. Corresponds directly to PORT DIALBACK and the presence of the label 'Dialback' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT dialPortDialbackNoUsername	1.3.6.1.4.1.33.13.5.1.1.5	INTEGER	read-write	Control which when enabled on a dialback port will not prompt for a username upon dialing back. Instead the original username is reused.
INT dialPortDialbackTimeout	1.3.6.1.4.1.33.13.5.1.1.3	INTEGER	read-write	The number of seconds to wait for remote modem response when dialing back. Corresponds directly to PORT DIALBACK TIMEOUT and the value labeled 'Dialback Timeout:' in the PORT ALTERNATE CHARACTERISTICS display.
INT dialPortDialout	1.3.6.1.4.1.33.13.5.1.1.4	INTEGER	read-write	A control to determine the state of a remote port after it has been logged out from the remote side of the connection. none will log out the port, query will ask user what to do, slip and ppp will revert to those protocols
INT dialPortIndex	1.3.6.1.4.1.33.13.5.1.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT menuIndex	1.3.6.1.4.1.33.13.3.4.1.1	INTEGER	read-only	The index number of a menu entry. Corresponds directly to the numbers down the left of the SERVER MENU display.
INT menuNestedEthernet	1.3.6.1.4.1.33.13.3.9	INTEGER	read-write	Control to request to download a menu script which is unique for this unit by prepending the Ethernet address, or 802.3 MAC address, of this unit to the nestedMenuName.
INT menuNestedScriptMaximum	1.3.6.1.4.1.33.13.3.7	INTEGER	read-write	Maximum number of temporary storage bytes for a nested menu script file. If not zero, the nested menu function is enabled.
INT menuNestedSystemName	1.3.6.1.4.1.33.13.3.8	INTEGER	read-write	Control to request to download a menu script which is unique for this unit by prepending the sysLocalName of this unit to the nestedMenuName.
INT menuPortIndex	1.3.6.1.4.1.33.13.3.5.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT menuPortMenuStatus	1.3.6.1.4.1.33.13.3.5.1.2	INTEGER	read-write	Control for menu operation on the port. Corresponds indirectly to PORT MENU and PORT PRIVILEGED MENU and the presence of the labels 'Menu' and 'Privileged Menu' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT menuPortNestedMenuPrivilege	1.3.6.1.4.1.33.13.3.5.1.4	INTEGER	read-write	Control for nested privileged menu operation on the port. Corresponds indirectly to PORT NESTED PRIVILEGED MENU and the presence of the label 'Nested Privileged Menu' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT menuPortNestedMenuStatus	1.3.6.1.4.1.33.13.3.5.1.3	INTEGER	read-write	Control for nested menu operation on the port. Corresponds indirectly to PORT NESTED MENU and the presence of the label 'Nested Menu' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT menuPortNestedTopLevel	1.3.6.1.4.1.33.13.3.5.1.5	INTEGER	read-write	The top level nested menu to select from the menu definition file.
INT menuStatus	1.3.6.1.4.1.33.13.3.4.1.2	INTEGER	read-write	The status of a the entry. Set to 'invalid' to remove the entry, which corresponds directly to the CLEAR SERVER MENU command. Actual removal of the entry is implementation specific.
INT netLoginNumber	1.3.6.1.4.1.33.13.4.1	INTEGER	read-only	The number of entries in the Network Login Server table.
INT netLoginPortIndex	1.3.6.1.4.1.33.13.4.3.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT netLoginPortScriptEcho	1.3.6.1.4.1.33.13.4.3.1.3	INTEGER	read-write	Control for display of script operation on the port when running a script. Corresponds directly to PORT SCRIPT ECHO and the presence of the label 'Script Echo' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT netLoginPortScriptUse	1.3.6.1.4.1.33.13.4.3.1.2	INTEGER	read-write	Control for the script action taken when a user logs in on the port. Corresponds directly to PORT SCRIPT LOGIN and the value labeled 'Script Login:' in the PORT ALTERNATE CHARACTERISTICS display.
INT netLoginServerStatus	1.3.6.1.4.1.33.13.4.2.1.2	INTEGER	read-write	Status of this entry. Set to 'invalid' to remove the entry, which corresponds directly to the CLEAR SERVER SCRIPT SERVER command. Actual removal of the entry is implementation specific.
INT queueJob	1.3.6.1.4.1.33.13.2.4.1.1	INTEGER	read-only	The job number of a queued request. Corresponds directly to the value labeled 'Entry' in the QUEUE display.
INT queueLimit	1.3.6.1.4.1.33.13.2.1	INTEGER	read-write	The maximum number of entries that can be made in the Queue table. The value -1 indicates the imit is available memory. Corresponds directly to SERVER QUEUE LIMIT and the value labeled 'Queue Limit:' in the SERVER CHARACTERISTICS display.
INT queuePortIndex	1.3.6.1.4.1.33.13.2.5.1.1	INTEGER	read-only	An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB.
INT queuePortQueuing	1.3.6.1.4.1.33.13.2.5.1.2	INTEGER	read-write	Control for allowing queued requests for using the port. Corresponds directly to PORT QUEUING and the presence of the label 'Queuing' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
INT queueServicePortIndex	1.3.6.1.4.1.33.13.2.4.1.5	INTEGER	read-only	The charPortIndex of the port for which the originator is waiting, if supplied by the originator. As defined in the standard Character MIB. Corresponds indirectly to the port number part of the value labeled 'Port Name' in the QUEUE display.
INT queueStatus	1.3.6.1.4.1.33.13.2.4.1.2	INTEGER	read-write	The status of a queue entry. Set to 'invalid' to remove the entry, which corresponds directly to the REMOVE QUEUE ENTRY command. Actual removal of the entry is implementation specific.
INT sessionLogConnectionID	1.3.6.1.4.1.33.13.6.2.1.2	INTEGER	read-only	An indentifying number for records relating to the same connection, that is, the connect and disconnect records, either of which can be missing. Corresponds directly to value labeled 'Entry' the SERVER ACCOUNTING display.
INT sessionLogEmpty	1.3.6.1.4.1.33.13.6.7	INTEGER	read-write	Control to empty the log. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes the log to be emptied.
INT sessionLogEvent	1.3.6.1.4.1.33.13.6.2.1.4	INTEGER	read-only	The type of event. Corresponds directly to the alphabetic part of the value labeled 'Type' in the SERVER ACCOUNTING display. Type 15 is used by internal processes that call the session log function with an already formatted message.
INT sessionLogEventDetail	1.3.6.1.4.1.33.13.6.2.1.5	INTEGER	read-only	The detailed reason for the event. Corresponds directly to the numeric part of the value labeled 'Type' in the SERVER ACCOUNTING display.
INT sessionLogFacility	1.3.6.1.4.1.33.13.6.8	INTEGER	read-write	The UNIX facility level that server originated accounting messages are logged to.
INT sessionLogHostSecondaryType	1.3.6.1.4.1.33.13.6.10	INTEGER	read-write	The type of secondary host to which session log events are to be sent. This value should be set to unix when configuring a non-zero sessionLogHostSecondaryAddress. Corresponds to the presence of the label 'SYSLOGD Host2' following the label 'Daemon(s)' in the SERVER UNIT display.
INT sessionLogHostType	1.3.6.1.4.1.33.13.6.3	INTEGER	read-write	The type of host to which session log events are to be sent.
INT sessionLogIndex	1.3.6.1.4.1.33.13.6.2.1.1	INTEGER	read-only	The index number of a session log entry. Corresponds directly to the order of the displayed records in the SERVER ACCOUNTING display. The maximum value is sessionLogLimit.
INT sessionLogLimit	1.3.6.1.4.1.33.13.6.1	INTEGER	read-write	The maximum number of entries allowed in the Session Log table. Corresponds directly to SERVER ACCOUNTING ENTRIES and the value labeled 'Accounting Entries:' in the SERVER CHARACTERISTICS display.
INT sessionLogPort	1.3.6.1.4.1.33.13.6.2.1.3	INTEGER	read-only	An index value that uniquely identifies the port where the event took place. The port identified by a particular value of this index is the same port as identified by charPortIndex in the standard Character MIB. Corresponds directly to the value labeled 'Port' in the SERVER ACCOUNTING display.
INT sessionLogPriority	1.3.6.1.4.1.33.13.6.6	INTEGER	read-write	The largest priority number for the system to log. Higher numbered (lower priority) events will not be logged.
INT sessionLogReliable	1.3.6.1.4.1.33.13.6.9	INTEGER	read-write	Control for reliable logging. Corresponds directly to the presence of the label 'Reliable Accounting' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display.
INT sessionLogTl1AutonomousLogSize	1.3.6.1.4.1.33.13.6.14	INTEGER	read-write	The size in bytes of the TL1 autonomous log, which records alarms. A change in log size will not take effect until rebooting the unit.
INT sessionLogTl1CommandLogSize	1.3.6.1.4.1.33.13.6.15	INTEGER	read-write	The size in bytes of the TL1 command log, which records all TL1 commands entered on this server. A change in log size will not take effect until rebooting the unit.
INT sessionLogVerbose	1.3.6.1.4.1.33.13.6.5	INTEGER	read-write	Control for verbose logging.
INT sessionLogVerboseEvent	1.3.6.1.4.1.33.13.6.2.1.12	INTEGER	read-only	When logging in 'verbose' mode, the event that occured.
INT sessionLogX25Direction	1.3.6.1.4.1.33.13.6.2.1.13	INTEGER	read-only	The initial direction for an X.25 connection. A value of 0 is returned if the session is not X25
INT sessionLogX25DisconnectCause	1.3.6.1.4.1.33.13.6.2.1.17	INTEGER	read-only	For a terminated X.25 connection, the standard, X.25 cause code.
INT sessionLogX25DisconnectDiagnostic	1.3.6.1.4.1.33.13.6.2.1.18	INTEGER	read-only	For a terminated X.25 connection, the standard, X.25 diagnostic code.
INT sessionLogZeroAccountingAll	1.3.6.1.4.1.33.13.6.12	INTEGER	read-write	A control to clear all entries in the accounting log including command log entries. Corresponds directly to the command CLEAR SERVER ACCOUNTING ALL. In response to a get-request or get-next-request the agent always returns ready for this value.
INT sessionLogZeroAlarmLogging	1.3.6.1.4.1.33.13.6.17	INTEGER	read-write	Control to clear all alarm log entries. In response to a get-request or a get-next-request the agent always returns ready for this value.
INT sessionLogZeroCommandLogging	1.3.6.1.4.1.33.13.6.13	INTEGER	read-write	A control to clear all command log entries. Corresponds directly to the command CLEAR SERVER COMMAND LOGGING. In response to a get-request or get-next-request the agent always returns ready for this value.
INT sessionLogZeroDataLogging	1.3.6.1.4.1.33.13.6.16	INTEGER	read-write	A control to clear all data log entries. Corresponds directly to the command CLEAR SERVER DATA LOGGING. In response to a get-request or get-next-request the agent always returns ready for this value.
IpAddress (1)
IP basicPortAlarmMasterUpdateFirmwareHost	1.3.6.1.4.1.33.13.1.17.1.67	IpAddress	read-write	The internet address of the server to use when downloading a new firmware image for the high density alarm unit attached to this port via TFTP. Corresponds directly to the UPDATE AMST FIRMWARE command's INTERNET ADDRESS parameter.
OCTET STRING (15)
OCT basicPortBreakSequence	1.3.6.1.4.1.33.13.1.17.1.51	OCTET STRING	read-write	A sequence of characters to be sent out the serial port on receipt of a Break from the network in lieu of a hardware break.
OCT basicPortControlledPortLogin	1.3.6.1.4.1.33.13.1.17.1.34	OCTET STRING	read-write	A control string to send out the serial port upon port login. Corresponds to the hexadecimal code which is represented in ASCII following the label 'Controlled Port Login:' in the PORT CONTROLLED display.
OCT basicPortControlledPortLogout	1.3.6.1.4.1.33.13.1.17.1.35	OCTET STRING	read-write	A control string to send out the serial port upon port logout. Corresponds to the hexadecimal code which is represented in ASCII following the label 'Controlled Port Logout:' in the PORT CONTROLLED display.
OCT basicPortControlledSessionInitialize	1.3.6.1.4.1.33.13.1.17.1.36	OCTET STRING	read-write	A control string to send out the serial port upon entering a session. Corresponds to the hexadecimal code which represented in ASCII following the label 'Controlled Session Initialize:' in the PORT CONTROLLED display.
OCT basicPortControlledSessionTerminate	1.3.6.1.4.1.33.13.1.17.1.37	OCTET STRING	read-write	A control string to send out the serial port upon exiting a session. Corresponds to the hexadecimal code which is represented in ASCII following the label 'Controlled Session Terminate:' in the PORT CONTROLLED display.
OCT basicPortDefaultDedicatedSessionType	1.3.6.1.4.1.33.13.1.17.1.42	OCTET STRING	read-write	A bit mask that specifies the default session type for a dedicated service for this port. The bit numbers are: 1;service name, 2;node name, 3;port name, 4, telnet console; 5, rlogin; 6, bridge console; 7, chassis console.
OCT basicSerialPortAPDDefaultProtocol	1.3.6.1.4.1.33.13.1.18.1.37	OCTET STRING	read-write	A bit map that specifies the protocol that this port will use when the time specified by basicSerialPortAPDTimeout has expired without sucessfully identifying the incoming porotocol. The bit numbers for the protocols are: None;Logout the port, 1;ARAP, 2;CSLIP, 3;Interactive, 4;SLIP, 5;PPP. Bits 6-16 are reserved for future use. Only one protocol may be specified for this object
OCT basicSerialPortAPDProtocols	1.3.6.1.4.1.33.13.1.18.1.35	OCTET STRING	read-write	A bit map that specifies the protocols that this port will attempt to detect using the Auto Protocol Detection function. The bit numbers for the protocols are: 1;ARAP, 3;Interactive, 4;SLIP, 5;PPP. Bits 6-16 are reserved for future use. More than one of these protocols may be ORed together. The default is 0 (zero) no protocols.
OCT broadcastGroupSlaves	1.3.6.1.4.1.33.13.8.1.1.4	OCTET STRING	read-write	A bitmap representing the ports included in this broadcast group. A bit with a value of '1' means the corresponding port is included in the broadcast group whereas a value of '0' indicates that the port is not part of the broadcast group.
OCT broadcastGroupSlavesBroadcastOnly	1.3.6.1.4.1.33.13.8.1.1.5	OCTET STRING	read-write	A bitmap representing the ports set up to discard input data and transmit only the broadcast data on the line. A bit set to '1' means that the corresponding port will only broadcast the data and discard any input.
OCT netLoginPortLoaderAddress	1.3.6.1.4.1.33.13.4.3.1.5	OCTET STRING	read-only	The network address of the server that provided the script for the current port login. Corresponds directly the address part of the value labeled 'Script Loaded From:' in the PORT STATUS display.
OCT sessionLogHostAddress	1.3.6.1.4.1.33.13.6.4	OCTET STRING	read-write	The address of the host to receive events.
OCT sessionLogHostSecondaryAddress	1.3.6.1.4.1.33.13.6.11	OCTET STRING	read-write	The address of a secondary host to receive events. Corresponds directly to the value labeled 'SYSLOGD Host2' in the SERVER UNIT display.
OCT sessionLogX25CalledAddress	1.3.6.1.4.1.33.13.6.2.1.16	OCTET STRING	read-only	For an X.25 connection, the X.121 destination address.
OCT sessionLogX25CallerAddress	1.3.6.1.4.1.33.13.6.2.1.15	OCTET STRING	read-only	For an X.25 connection, the X.121 source address.
TimeTicks (1)
TIK basicPortZeroTime	1.3.6.1.4.1.33.13.1.17.1.29	TimeTicks	read-only	The number of hundredths of a second since the most recent zeroing of the port's counters, such as through execution of basicPortZero. Corresponds directly to the value labeled 'Seconds Since Zeroed:' in the PORT COUNTERS display.
No type (72)
NTF alarmMasterInputStateChange	1.3.6.1.4.1.33.0.41			Indication that the alarm input point within a high density alarm management port transitioned to open or closed.
NTF alarmMasterNotResponding	1.3.6.1.4.1.33.0.39			Indication that the high density alarm management device lost or regained contact with the inReach port to which it was connected as indicated by the basicPortAlarmMasterStatus variable.
NTF asciiToTrapTranslation	1.3.6.1.4.1.33.0.42			This trap contains ASCII data, which arrived at serial port, was formatted as a trap, and sent out on the network.
basicAlarmMasterInputEntry	1.3.6.1.4.1.33.13.1.36.1		not-accessible	An entry in the basicAlarmMasterInputTable.
basicAlarmMasterInputTable	1.3.6.1.4.1.33.13.1.36		not-accessible	Information about the high density alarm manager's alarm inputs.
basicContactClosureOrAlarmInputEntry	1.3.6.1.4.1.33.13.1.25.1		not-accessible	An entry in the basicContactClosureOrAlarmInputTable.
basicContactClosureOrAlarmInputTable	1.3.6.1.4.1.33.13.1.25		not-accessible	Information about contact closures or alarm inputs.
basicControlOutputEntry	1.3.6.1.4.1.33.13.1.30.1		not-accessible	An entry in the basicControlOutputTable.
basicControlOutputRelayEntry	1.3.6.1.4.1.33.13.1.38.1		not-accessible	An entry in the basicControlOutputRelayTable.
basicControlOutputRelayTable	1.3.6.1.4.1.33.13.1.38		not-accessible	Information about controlled output relays.
basicControlOutputTable	1.3.6.1.4.1.33.13.1.30		not-accessible	Information about controlled output distribution points.
basicControlSignalEntry	1.3.6.1.4.1.33.13.1.28.1		not-accessible	An entry in the basicControlSignalTable.
basicControlSignalTable	1.3.6.1.4.1.33.13.1.28		not-accessible	Information about Environmental Manager Control Signal points.
basicHumiditySensorEntry	1.3.6.1.4.1.33.13.1.27.2.1		not-accessible	An entry in the basicHumiditySensorTable.
basicHumiditySensorTable	1.3.6.1.4.1.33.13.1.27.2		not-accessible	Information about Environmental Manager Humidity Sensors.
basicPortEntry	1.3.6.1.4.1.33.13.1.17.1		not-accessible	Basic parameter values for a port.
basicPortSessEntry	1.3.6.1.4.1.33.13.1.21.1		not-accessible	Status and parameter values for a basic port session.
basicPortSessionTable	1.3.6.1.4.1.33.13.1.21		not-accessible	A list of port session entries.
basicPortTable	1.3.6.1.4.1.33.13.1.17		not-accessible	A list of basic character port entries.
basicPortTrapEntry	1.3.6.1.4.1.33.13.1.35.1		not-accessible	Administrative status of signal change traps for a hardware port.
basicPortTrapTable	1.3.6.1.4.1.33.13.1.35		not-accessible	A list of traps associated with signal control changes on ports.
basicPowerMasterOutletEntry	1.3.6.1.4.1.33.13.1.37.1		not-accessible	An entry in the basicPowerMasterOutletTable.
basicPowerMasterOutletTable	1.3.6.1.4.1.33.13.1.37		not-accessible	Information about power master outlets.
basicPowerOutletEntry	1.3.6.1.4.1.33.13.1.26.1		not-accessible	An entry in the basicPowerOutletTable.
basicPowerOutletTable	1.3.6.1.4.1.33.13.1.26		not-accessible	Information about Environmental Manager Power Outlets.
basicSerialPortEntry	1.3.6.1.4.1.33.13.1.18.1		not-accessible	Basic parameter values for a serial port.
basicSerialPortTable	1.3.6.1.4.1.33.13.1.18		not-accessible	A list of basic character serial port entries.
basicTemperatureHumiditySensor	1.3.6.1.4.1.33.13.1.27
basicTemperatureSensorEntry	1.3.6.1.4.1.33.13.1.27.1.1		not-accessible	An entry in the basicTemperatureSensorTable.
basicTemperatureSensorTable	1.3.6.1.4.1.33.13.1.27.1		not-accessible	Information about Environmental Manager Temperature Sensors.
broadcastGroupEntry	1.3.6.1.4.1.33.13.8.1.1		not-accessible	Broadcast group information.
broadcastGroupTable	1.3.6.1.4.1.33.13.8.1		not-accessible	A list of broadcast groups.
cclParsedScriptEntry	1.3.6.1.4.1.33.13.7.1.1		not-accessible	Parsed CCL script information.
cclParsedScriptTable	1.3.6.1.4.1.33.13.7.1		not-accessible	A list of parsed CCL scripts.
cclPortEntry	1.3.6.1.4.1.33.13.7.2.1		not-accessible	CCL parameter values for a port.
cclPortTable	1.3.6.1.4.1.33.13.7.2		not-accessible	A list of ccl character port entries.
characterDep	1.3.6.1.4.1.33.2
NTF contactClosureChanged	1.3.6.1.4.1.33.0.30			Indication that the contact closure transitioned to open or closed.
dialPortEntry	1.3.6.1.4.1.33.13.5.1.1		not-accessible	Dial parameter values for a port.
dialPortTable	1.3.6.1.4.1.33.13.5.1		not-accessible	A list of dial character port entries.
NTF humidityThresholdExceeded	1.3.6.1.4.1.33.0.37			Indication that the humidity exceeded a threshhold and the value of the currrent humidity.
menuEntry	1.3.6.1.4.1.33.13.3.4.1		not-accessible	Parameter values for a menu entry.
menuPortEntry	1.3.6.1.4.1.33.13.3.5.1		not-accessible	Menu parameter values for a port.
menuPortTable	1.3.6.1.4.1.33.13.3.5		not-accessible	A list of menu-related character port entries.
menuTable	1.3.6.1.4.1.33.13.3.4		not-accessible	A list of menu entries.
netLoginPortEntry	1.3.6.1.4.1.33.13.4.3.1		not-accessible	Network login parameter values for a port.
netLoginPortTable	1.3.6.1.4.1.33.13.4.3		not-accessible	A list of network login character port entries.
netLoginServerEntry	1.3.6.1.4.1.33.13.4.2.1		not-accessible	Network login parameter values for a server entry.
netLoginServerTable	1.3.6.1.4.1.33.13.4.2		not-accessible	A list of network login server entries.
NTF portInputSignalChange	1.3.6.1.4.1.33.0.35			Indicates that an input signal on a port has transitioned to the state indicated in the variable rs232InSigState.
NTF portOutputSignalChange	1.3.6.1.4.1.33.0.36			Indicates that an output signal on a port has transitioned to the state indicated in the variable rs232OutSigState.
NTF powerAlarmFuseBankA	1.3.6.1.4.1.33.0.31			Indicates that a fuse from bank A tripped its breaker, or that it went operational. However, it is unlikely that a trap would be issued when the fuse starts working.
NTF powerAlarmFuseBankB	1.3.6.1.4.1.33.0.32			Indicates that a fuse from bank B tripped its breaker, or that it went operational. However, it is unlikely that a trap would be issued when the fuse starts working.
NTF powerMasterNotResponding	1.3.6.1.4.1.33.0.43			Indication that the power management port lost or regained contact with the power unit to which it was connected as indicated by the basicPortPowerMasterDeviceStatus variable.
NTF powerSupplyAlarmA	1.3.6.1.4.1.33.0.33			Indicates that power supply A lost or regained power. However, it is unlikely that a trap would be issued when the power comes on.
NTF powerSupplyAlarmB	1.3.6.1.4.1.33.0.34			Indicates that power supply B lost or regained power. However, it is unlikely that a trap would be issued when the power comes on.
queueEntry	1.3.6.1.4.1.33.13.2.4.1		not-accessible	Parameter values for a queue entry.
queuePortEntry	1.3.6.1.4.1.33.13.2.5.1		not-accessible	Queuing parameter values for a port.
queuePortTable	1.3.6.1.4.1.33.13.2.5		not-accessible	A list of queuing-related character port entries.
queueTable	1.3.6.1.4.1.33.13.2.4		not-accessible	A list of queue entries.
sessionLogEntry	1.3.6.1.4.1.33.13.6.2.1		not-accessible	Parameter values for a session log entry.
sessionLogTable	1.3.6.1.4.1.33.13.6.2		not-accessible	A list of session log entries.
NTF temperatureThresholdExceeded	1.3.6.1.4.1.33.0.38			Indication that the temperature exceeded a threshhold and the value of the currrent temperature.
xBasic	1.3.6.1.4.1.33.13.1
xBroadcastGroup	1.3.6.1.4.1.33.13.8
xCcl	1.3.6.1.4.1.33.13.7
xCharacter	1.3.6.1.4.1.33.13
xDial	1.3.6.1.4.1.33.13.5
xMenu	1.3.6.1.4.1.33.13.3
xNetLogin	1.3.6.1.4.1.33.13.4
xQueue	1.3.6.1.4.1.33.13.2
xSessionLog	1.3.6.1.4.1.33.13.6

RFC description

Manages character stream device configuration for iTouch systems including ports, sessions, and alarm functions.

Start monitoring iTouch console servers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ITOUCH-CHARACTER-MIB

This MIB depends on

Related MIBs

What Is ITOUCH-CHARACTER-MIB?

What Can Be Monitored

Supported Devices

Monitoring Examples

RFC description