ITOUCH-CHASSIS-MIB

All MIBs › ITOUCH-CHASSIS-MIB

Category: Device Management, Vendor: iTouch

Description:

iTouch chassis MIB providing SNMP objects for modular chassis hardware inventory, card status, and power management.

Imported Objects

MacAddress

From ITOUCH-MIB

AddressType
HardwareType
IOType
iTouch	OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress

From RFC1213-MIB

DisplayString

What Is ITOUCH-CHASSIS-MIB?

ITOUCH-CHASSIS-MIB is an iTouch Systems enterprise MIB providing SNMP visibility into a modular chassis-based device's hardware inventory, including installed cards/modules and power management. Its purpose is to represent the physical makeup of a chassis system so a management station can see which modules are present, their type, and their operational status. This makes it directly a hardware-status monitoring MIB: card presence and status objects reveal whether a module has failed or been removed, and power-management objects reveal power supply health, both of which are critical for detecting a hardware fault in a modular chassis before it causes a service outage. It conceptually parallels the standard ENTITY-MIB physical-entity model used by many chassis-based systems, though this module implements its own private enterprise structure. It is deployed on iTouch Systems modular chassis equipment, typically multiplexer or media-conversion platforms used in telecom and enterprise network environments. Engineers can download the ITOUCH-CHASSIS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ITOUCH-CHASSIS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

What Can Be Monitored

chassis card/slot status
power supply status
installed module presence and type

Supported Devices

iTouch Systems modular chassis network equipment

Monitoring Examples

No specific object or table names were available for this module, so a concrete polling scenario cannot be grounded in real identifiers; based on its stated purpose, though, an administrator would use it to check chassis card/slot inventory and power supply status to catch a failed or missing module in the chassis.

OIDs

OID symbolic	OID numeric	Type	Access	Description
MAC basicBase802Address	1.3.6.1.4.1.33.16.1.1	MacAddress	read-only	Base IEEE 802 global address for the chassis.
MAC basicNewBase802Address	1.3.6.1.4.1.33.16.1.4	MacAddress	read-write	New base IEEE 802 global address for the chassis. Must be set in conjunction with featType 'changeEthernetAddress' and featKey from the ITouch System MIB.
INT basicSlot	1.3.6.1.4.1.33.16.1.2	INTEGER	read-only	Chassis slot number (slotIndex) of the system whose agent is supplying this MIB.
INT basicSlotNumber	1.3.6.1.4.1.33.16.1.3	INTEGER	read-only	Number of slots in the chassis.
controllerEntry	1.3.6.1.4.1.33.16.4.1.1		not-accessible	Values for a controller.
INT controllerIndex	1.3.6.1.4.1.33.16.4.1.1.2	INTEGER	read-only	An index value that uniquely identifies a controller.
OID controllerNetwork	1.3.6.1.4.1.33.16.4.1.1.3	OBJECT IDENTIFIER	read-write	The instance identifier of the first object in the conceptual row entry for the segment, port, or controller this controller is to use, that is, segmentType, portType or controllerType.
controllerTable	1.3.6.1.4.1.33.16.4.1		not-accessible	A list of controller entries, one for each controller of each type on the local system.
NET controllerType	1.3.6.1.4.1.33.16.4.1.1.1	NetworkType	read-only	The controller type.
INT firmwareUpdateCompletionStatus	1.3.6.1.4.1.33.16.9.1.1.6	INTEGER	read-only	This variable indicates the completion status of the the last firmware update attempt. 'none' indicates that no firmware update has yet been attempted.
STR firmwareUpdateDefaultFileName	1.3.6.1.4.1.33.16.9.1.1.2	DisplayString	read-only	This variable when read will obtain the default file name from the target.
firmwareUpdateEntry	1.3.6.1.4.1.33.16.9.1.1		not-accessible	An entry in the table concerning the writing of firmware to a target I/O card.
STR firmwareUpdateFileName	1.3.6.1.4.1.33.16.9.1.1.3	DisplayString	read-write	This variable contains the name of the file to be read from the flash memory card and written to the target.
INT firmwareUpdateMethod	1.3.6.1.4.1.33.16.9.1.1.7	INTEGER	read-write	This variable indicates the method of update of the firmware update attempt.
INT firmwareUpdateSlotIndex	1.3.6.1.4.1.33.16.9.1.1.1	INTEGER	read-only	This variable identifies the slot to which is to be the target of the firmware update.
INT firmwareUpdateState	1.3.6.1.4.1.33.16.9.1.1.5	INTEGER	read-only	This variable indicates the current state of firmware update, 'idle' indicates that firmware update may be initiated, and 'writing' indicates that an update is in process.
INT firmwareUpdateStatus	1.3.6.1.4.1.33.16.9.1.1.4	INTEGER	read-write	This variable is used to start the update process. The agent always 'ready' for this value. Setting this value to 'execute' causes the agent to write the file specified by firmwareUpdateFileName to be written to the taget. Setting this value to 'execute' when firmwareUpdateFileName has not been written or when firmwareUpdateState is 'writing' causes bad value to be returned.
firmwareUpdateTable	1.3.6.1.4.1.33.16.9.1		not-accessible	Table of descriptive and status information concerning the writing of firmware to a target I/O card.
interfaceEntry	1.3.6.1.4.1.33.16.5.1.1		not-accessible	Values for an interface.
INT interfaceIndex	1.3.6.1.4.1.33.16.5.1.1.1	INTEGER	read-only	An index value that uniquely identifies an interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
OID interfaceNetwork	1.3.6.1.4.1.33.16.5.1.1.2	OBJECT IDENTIFIER	read-write	The instance identifier of the first object in the conceptual row entry for the segment, port, or controller this interface is to use, that is, segmentType, portType, or controllerType.
interfaceTable	1.3.6.1.4.1.33.16.5.1		not-accessible	A list of interface entries, corresponding to the MIB II Interface group. These are directly equivalent to hardware network controllers, and must be the lowest numbered interfaces on the system.
portEntry	1.3.6.1.4.1.33.16.3.4.1		not-accessible	Values for an I/O card port.
INT portIndex	1.3.6.1.4.1.33.16.3.4.1.2	INTEGER	read-only	An index value that uniquely identifies a port.
INT portIOCardOperStatus	1.3.6.1.4.1.33.16.3.3	INTEGER	read-only	Status of the I/O card relative to the function card in this slot.
SER portIOCardSerialNumber	1.3.6.1.4.1.33.16.3.2	SerialNumber	read-only	The ITouch serial number of the I/O card in this slot.
IOT portIOCardType	1.3.6.1.4.1.33.16.3.1	IOType	read-only	The hardware type of the I/O card in this slot.
portTable	1.3.6.1.4.1.33.16.3.4		not-accessible	A list of port entries, one for each port of each type on the slots I/O card.
NET portType	1.3.6.1.4.1.33.16.3.4.1.1	NetworkType	read-only	The port type.
INT powerSupplyAdminAction	1.3.6.1.4.1.33.16.8.1.1.2	INTEGER	read-write	Control to cause reset of the power supply. When read, the value is always 'ready'. Setting to 'reset' or 'resetHold' causes a single attempt to take that action, but does not ensure transition to any particular value of powerSupplyRedundancyStatus.
GAU powerSupplyChassisWatts	1.3.6.1.4.1.33.16.8.1.1.24	Gauge	read-only	Total watts of power currently drawn by the entire chassis. A value of 0 indicates unknown.
GAU powerSupplyChassisWattsMax	1.3.6.1.4.1.33.16.8.1.1.25	Gauge	read-only	Total maximum watts of power available from all the power supplies in the chassis. A value of 0 indicates unknown.
powerSupplyEntry	1.3.6.1.4.1.33.16.8.1.1		not-accessible	Values for a chassis power supply.
INT powerSupplyFanHistory	1.3.6.1.4.1.33.16.8.1.1.17	INTEGER	read-only	The status history of the power supply's fan.
INT powerSupplyFanStatus	1.3.6.1.4.1.33.16.8.1.1.10	INTEGER	read-only	The current status of the power supply's fan.
INT powerSupplyFirmwareVersion	1.3.6.1.4.1.33.16.8.1.1.3	INTEGER	read-only	Version number of power supply firmware.
INT powerSupplyHardwareInhibitHistory	1.3.6.1.4.1.33.16.8.1.1.18	INTEGER	read-only	The status history of the power supply's hardware inhibit.
INT powerSupplyHardwareInhibitStatus	1.3.6.1.4.1.33.16.8.1.1.11	INTEGER	read-only	The current status of the power supply's hardware inhibit.
INT powerSupplyHardwareType	1.3.6.1.4.1.33.16.8.1.1.26	INTEGER	read-only	The type of power supply.
INT powerSupplyIndex	1.3.6.1.4.1.33.16.8.1.1.1	INTEGER	read-only	An index value that uniquely identifies a power supply, in the range 1 to the number of power supply slots in the chassis.
INT powerSupplyMinus12History	1.3.6.1.4.1.33.16.8.1.1.14	INTEGER	read-only	History of the -12 volt power from the power supply.
INT powerSupplyMinus12Status	1.3.6.1.4.1.33.16.8.1.1.7	INTEGER	read-only	Status of the -12 volt power from the power supply.
GAU powerSupplyMinus12Volts	1.3.6.1.4.1.33.16.8.1.1.21	Gauge	read-only	In hundredths, volts of -12 volt power currently provided by the power supply. A value of 0 indicates unknown.
INT powerSupplyPlus12History	1.3.6.1.4.1.33.16.8.1.1.13	INTEGER	read-only	History of the +12 volt power from the power supply.
INT powerSupplyPlus12Status	1.3.6.1.4.1.33.16.8.1.1.6	INTEGER	read-only	Status of the +12 volt power from the power supply.
GAU powerSupplyPlus12Volts	1.3.6.1.4.1.33.16.8.1.1.20	Gauge	read-only	In hundredths, volts of +12 volt power currently provided by the power supply. A value of 0 indicates unknown.
INT powerSupplyPlus5History	1.3.6.1.4.1.33.16.8.1.1.12	INTEGER	read-only	History of the +5 volt power from the power supply.
INT powerSupplyPlus5Status	1.3.6.1.4.1.33.16.8.1.1.5	INTEGER	read-only	Status of the +5 volt power from the power supply.
GAU powerSupplyPlus5Volts	1.3.6.1.4.1.33.16.8.1.1.19	Gauge	read-only	In hundredths, volts of +5 volt power currently provided by the power supply. A value of 0 indicates unknown.
INT powerSupplyRedundancyStatus	1.3.6.1.4.1.33.16.8.1.1.4	INTEGER	read-only	The current redundancy status of the power supply.
powerSupplyTable	1.3.6.1.4.1.33.16.8.1		not-accessible	A list of power supply entries.
INT powerSupplyThermalShutdownHistory	1.3.6.1.4.1.33.16.8.1.1.16	INTEGER	read-only	The thermal shutdown history of the power supply.
INT powerSupplyThermalShutdownStatus	1.3.6.1.4.1.33.16.8.1.1.9	INTEGER	read-only	The current thermal shutdown status of the power supply.
INT powerSupplyThermalWarningHistory	1.3.6.1.4.1.33.16.8.1.1.15	INTEGER	read-only	The thermal warning history of the power supply.
INT powerSupplyThermalWarningStatus	1.3.6.1.4.1.33.16.8.1.1.8	INTEGER	read-only	The current thermal warning status of the power supply.
GAU powerSupplyWatts	1.3.6.1.4.1.33.16.8.1.1.22	Gauge	read-only	Watts of power currently drawn from this power supply. A value of 0 indicates unknown.
GAU powerSupplyWattsMax	1.3.6.1.4.1.33.16.8.1.1.23	Gauge	read-only	Maximum watts of power available from this power supply. A value of 0 indicates unknown.
segmentEntry	1.3.6.1.4.1.33.16.2.1.1		not-accessible	Values for a chassis segment.
LET segmentIndex	1.3.6.1.4.1.33.16.2.1.1.2	Letter	read-only	An index value that uniquely identifies a segment.
segmentTable	1.3.6.1.4.1.33.16.2.1		not-accessible	A list of segment entries, one for each segment of each type on the chassis.
NET segmentType	1.3.6.1.4.1.33.16.2.1.1.1	NetworkType	read-only	The segment type.
INT slotAdminAction	1.3.6.1.4.1.33.16.7.1.1.2	INTEGER	read-write	Control to cause reset of the system in a slot. When read, the value is always 'ready'. Setting to 'reset' or 'resetHold' causes a single attempt to take that action, but does not ensure transition to any particular value of slotOperStatus.
MAC slotBase802Address	1.3.6.1.4.1.33.16.7.1.1.16	MacAddress	read-only	Base IEEE 802 global address for the slot.
MAC slotBoot802Address	1.3.6.1.4.1.33.16.7.2.1.5	MacAddress	read-only	IEEE 802 global address in use for bootstrap operation.
OCT slotBootAddress	1.3.6.1.4.1.33.16.7.2.1.7	OCTET STRING	read-only	The network address the system in the slot is using to identify itself for bootstrap operation.
ADR slotBootAddressType	1.3.6.1.4.1.33.16.7.2.1.6	AddressType	read-only	The type of network address contained in slotBootAddress.
GAU slotBootBlockNumber	1.3.6.1.4.1.33.16.7.2.1.12	Gauge	read-only	The current block number being transferred for bootstrap operation, zero if unknown or not applicable.
OID slotBootControlController	1.3.6.1.4.1.33.16.6.1.1.4	OBJECT IDENTIFIER	read-write	The instance identifier of the first object in the conceptual row entry for the controller this entry selects for bootstrap operation, that is, controllerType. This entry must be compatible with slotBootControlNetwork, including being of the same network type. The value 0.0 indicates default action.
slotBootControlEntry	1.3.6.1.4.1.33.16.6.1.1		not-accessible	Values for a chassis slot.
INT slotBootControlFlagDumpBootpTftp	1.3.6.1.4.1.33.16.6.2.1.3	INTEGER	read-write	Control for performing dump over BOOTP/TFTP.
INT slotBootControlFlagDumpLocal	1.3.6.1.4.1.33.16.6.2.1.9	INTEGER	read-write	Control for performing dump from a local device.
INT slotBootControlFlagDumpMop	1.3.6.1.4.1.33.16.6.2.1.12	INTEGER	read-write	Control for performing dump over Digital's MOP.
INT slotBootControlFlagDumpRarpTftp	1.3.6.1.4.1.33.16.6.2.1.18	INTEGER	read-write	Control for performing dump over RARP/TFTP.
INT slotBootControlFlagDumpTftpDirect	1.3.6.1.4.1.33.16.6.2.1.6	INTEGER	read-write	Control for performing dump over direct TFTP.
INT slotBootControlFlagDumpXmop	1.3.6.1.4.1.33.16.6.2.1.15	INTEGER	read-write	Control for performing dump over ITouch extended MOP.
slotBootControlFlagEntry	1.3.6.1.4.1.33.16.6.2.1		not-accessible	Values for a boot control flag.
INT slotBootControlFlagLoadBootpTftp	1.3.6.1.4.1.33.16.6.2.1.1	INTEGER	read-write	Control for performing load over BOOTP/TFTP.
INT slotBootControlFlagLoadLocal	1.3.6.1.4.1.33.16.6.2.1.7	INTEGER	read-write	Control for performing load from a local device.
INT slotBootControlFlagLoadMop	1.3.6.1.4.1.33.16.6.2.1.10	INTEGER	read-write	Control for performing load over Digital's MOP.
INT slotBootControlFlagLoadRarpTftp	1.3.6.1.4.1.33.16.6.2.1.16	INTEGER	read-write	Control for performing load over RARP/TFTP.
INT slotBootControlFlagLoadTftpDirect	1.3.6.1.4.1.33.16.6.2.1.4	INTEGER	read-write	Control for performing load over direct TFTP.
INT slotBootControlFlagLoadXmop	1.3.6.1.4.1.33.16.6.2.1.13	INTEGER	read-write	Control for performing load over ITouch extended MOP.
INT slotBootControlFlagParamBootpTftp	1.3.6.1.4.1.33.16.6.2.1.2	INTEGER	read-write	Control for performing parameter load over BOOTP/TFTP.
INT slotBootControlFlagParamLocal	1.3.6.1.4.1.33.16.6.2.1.8	INTEGER	read-write	Control for performing parameter load from a local device.
INT slotBootControlFlagParamMop	1.3.6.1.4.1.33.16.6.2.1.11	INTEGER	read-write	Control for performing parameter load over Digital's MOP.
INT slotBootControlFlagParamRarpTftp	1.3.6.1.4.1.33.16.6.2.1.17	INTEGER	read-write	Control for performing parameter load over RARP/TFTP.
INT slotBootControlFlagParamTftpDirect	1.3.6.1.4.1.33.16.6.2.1.5	INTEGER	read-write	Control for performing parameter load over direct TFTP.
INT slotBootControlFlagParamXmop	1.3.6.1.4.1.33.16.6.2.1.14	INTEGER	read-write	Control for performing parameter load over ITouch extended MOP.
slotBootControlFlagTable	1.3.6.1.4.1.33.16.6.2		not-accessible	A list of slot boot control source flag entries.
INT slotBootControlIndex	1.3.6.1.4.1.33.16.6.1.1.2	INTEGER	read-only	An index value that uniquely identifies a boot control entry, from 1 to the number of entries for the slot.
IP slotBootControlInternetAddress	1.3.6.1.4.1.33.16.6.1.1.8	IpAddress	read-write	The internet address of the system is to use for itself when loading via TFTP. The value 0.0.0.0 indicates default action.
STR slotBootControlInternetDelimiter	1.3.6.1.4.1.33.16.6.1.1.11	DisplayString	read-write	The character separating the load file directory name from the file name.
STR slotBootControlInternetFile	1.3.6.1.4.1.33.16.6.1.1.7	DisplayString	read-write	The filename to request when loading an image via TFTP.
IP slotBootControlInternetGateway	1.3.6.1.4.1.33.16.6.1.1.10	IpAddress	read-write	The internet address of the gateway to use when loading an image via TFTP. The value 0.0.0.0 indicates default action.
IP slotBootControlInternetServer	1.3.6.1.4.1.33.16.6.1.1.9	IpAddress	read-write	The internet address of the server to use when loading an image via TFTP. The value 0.0.0.0 indicates default action.
STR slotBootControlMopFile	1.3.6.1.4.1.33.16.6.1.1.6	DisplayString	read-write	The software file name to request for down-line load of the server via MOP or XMOP.
OID slotBootControlNetwork	1.3.6.1.4.1.33.16.6.1.1.5	OBJECT IDENTIFIER	read-write	The instance identifier of the first object in the conceptual row entry for the segment or port this entry selects for bootstrap operation, that is, segmentType or portType. This entry must be compatible with slotBootControlController, including being of the same network type. The value 0.0 indicates default action.
INT slotBootControlSlot	1.3.6.1.4.1.33.16.6.1.1.1	INTEGER	read-only	An index value that uniquely identifies a slot, defined the same as slotIndex.
INT slotBootControlStatus	1.3.6.1.4.1.33.16.6.1.1.3	INTEGER	read-write	The status of the entry. Set to 'disabled' to disable the entry.
INT slotBootControlStorageClientSlot	1.3.6.1.4.1.33.16.6.3.1.1	INTEGER	read-only	An index value that uniquely identifies a slot, defined the same as slotIndex.
slotBootControlStorageEntry	1.3.6.1.4.1.33.16.6.3.1		not-accessible	Values for a chassis slot.
CTR slotBootControlStorageFailures	1.3.6.1.4.1.33.16.6.3.1.4	Counter	read-only	The number of times a read from or write to a given Storage location failed
INT slotBootControlStorageServerSlot	1.3.6.1.4.1.33.16.6.3.1.2	INTEGER	read-only	An index value that uniquely identifies the slot in which the Storage record resides, with the same values as slotIndex.
INT slotBootControlStorageStatus	1.3.6.1.4.1.33.16.6.3.1.3	INTEGER	read-only	The status of the entry.
slotBootControlStorageTable	1.3.6.1.4.1.33.16.6.3		not-accessible	A list of slot boot control Storage entries.
slotBootControlTable	1.3.6.1.4.1.33.16.6.1		not-accessible	A list of slot boot control entries.
OCT slotBootCrashCode	1.3.6.1.4.1.33.16.7.2.1.13	OCTET STRING	read-only	If slotOperStatus is dumpRequested or dumping, a code number to identify the crash reason; otherwise zero length.
slotBootEntry	1.3.6.1.4.1.33.16.7.2.1		not-accessible	Bootstrap status values for a chassis slot.
STR slotBootFileName	1.3.6.1.4.1.33.16.7.2.1.11	DisplayString	read-only	The full name of the file in use for bootstrap operation.
IP slotBootGatewayAddress	1.3.6.1.4.1.33.16.7.2.1.10	IpAddress	read-only	The internet address of the router in use for bootstrap operation.
INT slotBootIfIndex	1.3.6.1.4.1.33.16.7.2.1.2	INTEGER	read-only	An index value that uniquely identifies the interface in use for bootstrap functions. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
INT slotBootIndex	1.3.6.1.4.1.33.16.7.2.1.1	INTEGER	read-only	An index value that uniquely identifies a slot, defined the same as slotIndex.
OID slotBootNetwork	1.3.6.1.4.1.33.16.7.2.1.3	OBJECT IDENTIFIER	read-only	The instance identifier of the first object in the conceptual row entry for the segment or port this interface is using, that is, segmentType or portType.
INT slotBootProtocol	1.3.6.1.4.1.33.16.7.2.1.4	INTEGER	read-only	The protocol in use for bootstrap operation.
OCT slotBootServerAddress	1.3.6.1.4.1.33.16.7.2.1.9	OCTET STRING	read-only	The network address of the system supplying bootstrap services to the system in the slot.
ADR slotBootServerAddressType	1.3.6.1.4.1.33.16.7.2.1.8	AddressType	read-only	The type of network address contained in slotBootServerAddress.
INT slotBootstrapFirmwareRevision	1.3.6.1.4.1.33.16.7.1.1.11	INTEGER	read-only	The firmware revision level of the bootstrap ROM installed in the system in the slot.
slotBootTable	1.3.6.1.4.1.33.16.7.2		not-accessible	A list of slot bootstrap status entries. A given slot has an entry in this table only when slotOperStatus is one of: loadRequested, loading, dumpRequested, dumping, paramRequested, paramLoading
slotControllerEntry	1.3.6.1.4.1.33.16.7.3.1		not-accessible	Values for a controller.
INT slotControllerIndex	1.3.6.1.4.1.33.16.7.3.1.2	INTEGER	read-only	An index value that uniquely identifies a controller.
OID slotControllerNetwork	1.3.6.1.4.1.33.16.7.3.1.3	OBJECT IDENTIFIER	read-only	The instance identifier of the first object in the conceptual row entry for the segment or port this controller is to use, that is, segmentType or portType.
slotControllerTable	1.3.6.1.4.1.33.16.7.3		not-accessible	A list of controller entries, one for each controller of each type in each slot.
NET slotControllerType	1.3.6.1.4.1.33.16.7.3.1.1	NetworkType	read-only	The controller type.
INT slotDefaultNVS	1.3.6.1.4.1.33.16.7.1.1.26	INTEGER	read-write	Setting to 'execute' causes non-volatile stored parameters to be reset to factory defaults. Setting to 'ready' has no effect.
INT slotElementalFirmwareRevision	1.3.6.1.4.1.33.16.7.1.1.12	INTEGER	read-only	The firmware revision level of the minimal function ROM (management bus microprocessor) installed in the system in the slot.
slotEntry	1.3.6.1.4.1.33.16.7.1.1		not-accessible	Values for a chassis slot.
INT slotHardwareRevision	1.3.6.1.4.1.33.16.7.1.1.7	INTEGER	read-only	This revision level of the function card hardware in the slot.
SER slotHardwareSerialNumber	1.3.6.1.4.1.33.16.7.1.1.6	SerialNumber	read-only	The ITouch serial number of the function card hardware in this slot.
HAR slotHardwareType	1.3.6.1.4.1.33.16.7.1.1.5	HardwareType	read-only	The type of hardware in the slot.
INT slotIndex	1.3.6.1.4.1.33.16.7.1.1.1	INTEGER	read-only	An index value that uniquely identifies a slot, in the range 0 to basicSlotNumber, where the value 0 indicates the same slot as basicSlot. As the objects found at instance zero are duplicates, that instance does not appear in responses a get-next, that is, the lowest numbered slotIndex returned by get-next is 1.
INT slotIOCardHardwareVersion	1.3.6.1.4.1.33.16.7.1.1.24	INTEGER	read-only	Version number of I/O card in the slot.
INT slotIOCardOperStatus	1.3.6.1.4.1.33.16.7.1.1.10	INTEGER	read-only	Status of the I/O card relative to the function card in this slot.
SER slotIOCardSerialNumber	1.3.6.1.4.1.33.16.7.1.1.9	SerialNumber	read-only	The ITouch serial number of the I/O card in this slot.
IOT slotIOCardType	1.3.6.1.4.1.33.16.7.1.1.8	IOType	read-only	The hardware type of the I/O card in this slot.
IP slotIpAddress	1.3.6.1.4.1.33.16.7.1.1.17	IpAddress	read-only	An internet address to which the system in this slot might respond. May be one of many.
GAU slotLedNumber	1.3.6.1.4.1.33.16.7.1.1.14	Gauge	read-only	The number of LEDs on the system in the slot. A value of 0 indicates none, unknown, or status not readable.
OCT slotLedStatus	1.3.6.1.4.1.33.16.7.1.1.15	OCTET STRING	read-only	The status of the LEDs displayed on the front and back of the system in the slot. The first bit is the high-order bit of the first byte of the value, proceeding to the low-order bit, then to then next byte. On the system hardware, the first LED is at the top, left, front, proceeding left to right, top to bottom, and front to back.
INT slotMemorySize	1.3.6.1.4.1.33.16.7.1.1.13	INTEGER	read-only	The number of bytes of memory installed in the system in the slot.
INT slotMinus12Status	1.3.6.1.4.1.33.16.7.1.1.20	INTEGER	read-only	Status of the -12 volt power to the slot.
GAU slotMinus12Watts	1.3.6.1.4.1.33.16.7.1.1.23	Gauge	read-only	Tenths of watts of -12 volt power currently drawn by the slot.
INT slotOperStatus	1.3.6.1.4.1.33.16.7.1.1.3	INTEGER	read-only	Relative to the chassis, the current operating status of the system in the slot.
INT slotPlus12Status	1.3.6.1.4.1.33.16.7.1.1.19	INTEGER	read-only	Status of the +12 volt power to the slot.
GAU slotPlus12Watts	1.3.6.1.4.1.33.16.7.1.1.22	Gauge	read-only	Tenths of watts of +12 volt power currently drawn by the slot.
INT slotPlus5Status	1.3.6.1.4.1.33.16.7.1.1.18	INTEGER	read-only	Status of the +5 volt power to the slot.
GAU slotPlus5Watts	1.3.6.1.4.1.33.16.7.1.1.21	Gauge	read-only	Tenths of watts of +5 volt power currently drawn by the slot.
INT slotRestoreNVS	1.3.6.1.4.1.33.16.7.1.1.25	INTEGER	read-write	Setting to 'execute' causes the non-volatile parameter storage to be restored from an installed memory card. Setting to 'ready' has no effect.
GAU slotSecondsSinceReset	1.3.6.1.4.1.33.16.7.1.1.4	Gauge	read-only	The number of seconds since the system in the slot was last reset by hardware or software.
slotTable	1.3.6.1.4.1.33.16.7.1		not-accessible	A list of slot entries.
xChassis	1.3.6.1.4.1.33.16
xChassisBasic	1.3.6.1.4.1.33.16.1
xController	1.3.6.1.4.1.33.16.4
xFirmwareUpdate	1.3.6.1.4.1.33.16.9
xInterface	1.3.6.1.4.1.33.16.5
xPort	1.3.6.1.4.1.33.16.3
xPowerSupply	1.3.6.1.4.1.33.16.8
xSegment	1.3.6.1.4.1.33.16.2
xSlot	1.3.6.1.4.1.33.16.7
xSlotBootControl	1.3.6.1.4.1.33.16.6

OID symbolic	OID numeric	Type	Access	Description
xChassis	1.3.6.1.4.1.33.16
xChassisBasic	1.3.6.1.4.1.33.16.1
MAC basicBase802Address	1.3.6.1.4.1.33.16.1.1	MacAddress	read-only	Base IEEE 802 global address for the chassis.
INT basicSlot	1.3.6.1.4.1.33.16.1.2	INTEGER	read-only	Chassis slot number (slotIndex) of the system whose agent is supplying this MIB.
INT basicSlotNumber	1.3.6.1.4.1.33.16.1.3	INTEGER	read-only	Number of slots in the chassis.
MAC basicNewBase802Address	1.3.6.1.4.1.33.16.1.4	MacAddress	read-write	New base IEEE 802 global address for the chassis. Must be set in conjunction with featType 'changeEthernetAddress' and featKey from the ITouch System MIB.
xSegment	1.3.6.1.4.1.33.16.2
segmentTable	1.3.6.1.4.1.33.16.2.1		not-accessible	A list of segment entries, one for each segment of each type on the chassis.
segmentEntry	1.3.6.1.4.1.33.16.2.1.1		not-accessible	Values for a chassis segment.
NET segmentType	1.3.6.1.4.1.33.16.2.1.1.1	NetworkType	read-only	The segment type.
LET segmentIndex	1.3.6.1.4.1.33.16.2.1.1.2	Letter	read-only	An index value that uniquely identifies a segment.
xPort	1.3.6.1.4.1.33.16.3
IOT portIOCardType	1.3.6.1.4.1.33.16.3.1	IOType	read-only	The hardware type of the I/O card in this slot.
SER portIOCardSerialNumber	1.3.6.1.4.1.33.16.3.2	SerialNumber	read-only	The ITouch serial number of the I/O card in this slot.
INT portIOCardOperStatus	1.3.6.1.4.1.33.16.3.3	INTEGER	read-only	Status of the I/O card relative to the function card in this slot.
portTable	1.3.6.1.4.1.33.16.3.4		not-accessible	A list of port entries, one for each port of each type on the slots I/O card.
portEntry	1.3.6.1.4.1.33.16.3.4.1		not-accessible	Values for an I/O card port.
NET portType	1.3.6.1.4.1.33.16.3.4.1.1	NetworkType	read-only	The port type.
INT portIndex	1.3.6.1.4.1.33.16.3.4.1.2	INTEGER	read-only	An index value that uniquely identifies a port.
xController	1.3.6.1.4.1.33.16.4
controllerTable	1.3.6.1.4.1.33.16.4.1		not-accessible	A list of controller entries, one for each controller of each type on the local system.
controllerEntry	1.3.6.1.4.1.33.16.4.1.1		not-accessible	Values for a controller.
NET controllerType	1.3.6.1.4.1.33.16.4.1.1.1	NetworkType	read-only	The controller type.
INT controllerIndex	1.3.6.1.4.1.33.16.4.1.1.2	INTEGER	read-only	An index value that uniquely identifies a controller.
OID controllerNetwork	1.3.6.1.4.1.33.16.4.1.1.3	OBJECT IDENTIFIER	read-write	The instance identifier of the first object in the conceptual row entry for the segment, port, or controller this controller is to use, that is, segmentType, portType or controllerType.
xInterface	1.3.6.1.4.1.33.16.5
interfaceTable	1.3.6.1.4.1.33.16.5.1		not-accessible	A list of interface entries, corresponding to the MIB II Interface group. These are directly equivalent to hardware network controllers, and must be the lowest numbered interfaces on the system.
interfaceEntry	1.3.6.1.4.1.33.16.5.1.1		not-accessible	Values for an interface.
INT interfaceIndex	1.3.6.1.4.1.33.16.5.1.1.1	INTEGER	read-only	An index value that uniquely identifies an interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
OID interfaceNetwork	1.3.6.1.4.1.33.16.5.1.1.2	OBJECT IDENTIFIER	read-write	The instance identifier of the first object in the conceptual row entry for the segment, port, or controller this interface is to use, that is, segmentType, portType, or controllerType.
xSlotBootControl	1.3.6.1.4.1.33.16.6
slotBootControlTable	1.3.6.1.4.1.33.16.6.1		not-accessible	A list of slot boot control entries.
slotBootControlEntry	1.3.6.1.4.1.33.16.6.1.1		not-accessible	Values for a chassis slot.
INT slotBootControlSlot	1.3.6.1.4.1.33.16.6.1.1.1	INTEGER	read-only	An index value that uniquely identifies a slot, defined the same as slotIndex.
INT slotBootControlIndex	1.3.6.1.4.1.33.16.6.1.1.2	INTEGER	read-only	An index value that uniquely identifies a boot control entry, from 1 to the number of entries for the slot.
INT slotBootControlStatus	1.3.6.1.4.1.33.16.6.1.1.3	INTEGER	read-write	The status of the entry. Set to 'disabled' to disable the entry.
OID slotBootControlController	1.3.6.1.4.1.33.16.6.1.1.4	OBJECT IDENTIFIER	read-write	The instance identifier of the first object in the conceptual row entry for the controller this entry selects for bootstrap operation, that is, controllerType. This entry must be compatible with slotBootControlNetwork, including being of the same network type. The value 0.0 indicates default action.
OID slotBootControlNetwork	1.3.6.1.4.1.33.16.6.1.1.5	OBJECT IDENTIFIER	read-write	The instance identifier of the first object in the conceptual row entry for the segment or port this entry selects for bootstrap operation, that is, segmentType or portType. This entry must be compatible with slotBootControlController, including being of the same network type. The value 0.0 indicates default action.
STR slotBootControlMopFile	1.3.6.1.4.1.33.16.6.1.1.6	DisplayString	read-write	The software file name to request for down-line load of the server via MOP or XMOP.
STR slotBootControlInternetFile	1.3.6.1.4.1.33.16.6.1.1.7	DisplayString	read-write	The filename to request when loading an image via TFTP.
IP slotBootControlInternetAddress	1.3.6.1.4.1.33.16.6.1.1.8	IpAddress	read-write	The internet address of the system is to use for itself when loading via TFTP. The value 0.0.0.0 indicates default action.
IP slotBootControlInternetServer	1.3.6.1.4.1.33.16.6.1.1.9	IpAddress	read-write	The internet address of the server to use when loading an image via TFTP. The value 0.0.0.0 indicates default action.
IP slotBootControlInternetGateway	1.3.6.1.4.1.33.16.6.1.1.10	IpAddress	read-write	The internet address of the gateway to use when loading an image via TFTP. The value 0.0.0.0 indicates default action.
STR slotBootControlInternetDelimiter	1.3.6.1.4.1.33.16.6.1.1.11	DisplayString	read-write	The character separating the load file directory name from the file name.
slotBootControlFlagTable	1.3.6.1.4.1.33.16.6.2		not-accessible	A list of slot boot control source flag entries.
slotBootControlFlagEntry	1.3.6.1.4.1.33.16.6.2.1		not-accessible	Values for a boot control flag.
INT slotBootControlFlagLoadBootpTftp	1.3.6.1.4.1.33.16.6.2.1.1	INTEGER	read-write	Control for performing load over BOOTP/TFTP.
INT slotBootControlFlagParamBootpTftp	1.3.6.1.4.1.33.16.6.2.1.2	INTEGER	read-write	Control for performing parameter load over BOOTP/TFTP.
INT slotBootControlFlagDumpBootpTftp	1.3.6.1.4.1.33.16.6.2.1.3	INTEGER	read-write	Control for performing dump over BOOTP/TFTP.
INT slotBootControlFlagLoadTftpDirect	1.3.6.1.4.1.33.16.6.2.1.4	INTEGER	read-write	Control for performing load over direct TFTP.
INT slotBootControlFlagParamTftpDirect	1.3.6.1.4.1.33.16.6.2.1.5	INTEGER	read-write	Control for performing parameter load over direct TFTP.
INT slotBootControlFlagDumpTftpDirect	1.3.6.1.4.1.33.16.6.2.1.6	INTEGER	read-write	Control for performing dump over direct TFTP.
INT slotBootControlFlagLoadLocal	1.3.6.1.4.1.33.16.6.2.1.7	INTEGER	read-write	Control for performing load from a local device.
INT slotBootControlFlagParamLocal	1.3.6.1.4.1.33.16.6.2.1.8	INTEGER	read-write	Control for performing parameter load from a local device.
INT slotBootControlFlagDumpLocal	1.3.6.1.4.1.33.16.6.2.1.9	INTEGER	read-write	Control for performing dump from a local device.
INT slotBootControlFlagLoadMop	1.3.6.1.4.1.33.16.6.2.1.10	INTEGER	read-write	Control for performing load over Digital's MOP.
INT slotBootControlFlagParamMop	1.3.6.1.4.1.33.16.6.2.1.11	INTEGER	read-write	Control for performing parameter load over Digital's MOP.
INT slotBootControlFlagDumpMop	1.3.6.1.4.1.33.16.6.2.1.12	INTEGER	read-write	Control for performing dump over Digital's MOP.
INT slotBootControlFlagLoadXmop	1.3.6.1.4.1.33.16.6.2.1.13	INTEGER	read-write	Control for performing load over ITouch extended MOP.
INT slotBootControlFlagParamXmop	1.3.6.1.4.1.33.16.6.2.1.14	INTEGER	read-write	Control for performing parameter load over ITouch extended MOP.
INT slotBootControlFlagDumpXmop	1.3.6.1.4.1.33.16.6.2.1.15	INTEGER	read-write	Control for performing dump over ITouch extended MOP.
INT slotBootControlFlagLoadRarpTftp	1.3.6.1.4.1.33.16.6.2.1.16	INTEGER	read-write	Control for performing load over RARP/TFTP.
INT slotBootControlFlagParamRarpTftp	1.3.6.1.4.1.33.16.6.2.1.17	INTEGER	read-write	Control for performing parameter load over RARP/TFTP.
INT slotBootControlFlagDumpRarpTftp	1.3.6.1.4.1.33.16.6.2.1.18	INTEGER	read-write	Control for performing dump over RARP/TFTP.
slotBootControlStorageTable	1.3.6.1.4.1.33.16.6.3		not-accessible	A list of slot boot control Storage entries.
slotBootControlStorageEntry	1.3.6.1.4.1.33.16.6.3.1		not-accessible	Values for a chassis slot.
INT slotBootControlStorageClientSlot	1.3.6.1.4.1.33.16.6.3.1.1	INTEGER	read-only	An index value that uniquely identifies a slot, defined the same as slotIndex.
INT slotBootControlStorageServerSlot	1.3.6.1.4.1.33.16.6.3.1.2	INTEGER	read-only	An index value that uniquely identifies the slot in which the Storage record resides, with the same values as slotIndex.
INT slotBootControlStorageStatus	1.3.6.1.4.1.33.16.6.3.1.3	INTEGER	read-only	The status of the entry.
CTR slotBootControlStorageFailures	1.3.6.1.4.1.33.16.6.3.1.4	Counter	read-only	The number of times a read from or write to a given Storage location failed
xSlot	1.3.6.1.4.1.33.16.7
slotTable	1.3.6.1.4.1.33.16.7.1		not-accessible	A list of slot entries.
slotEntry	1.3.6.1.4.1.33.16.7.1.1		not-accessible	Values for a chassis slot.
INT slotIndex	1.3.6.1.4.1.33.16.7.1.1.1	INTEGER	read-only	An index value that uniquely identifies a slot, in the range 0 to basicSlotNumber, where the value 0 indicates the same slot as basicSlot. As the objects found at instance zero are duplicates, that instance does not appear in responses a get-next, that is, the lowest numbered slotIndex returned by get-next is 1.
INT slotAdminAction	1.3.6.1.4.1.33.16.7.1.1.2	INTEGER	read-write	Control to cause reset of the system in a slot. When read, the value is always 'ready'. Setting to 'reset' or 'resetHold' causes a single attempt to take that action, but does not ensure transition to any particular value of slotOperStatus.
INT slotOperStatus	1.3.6.1.4.1.33.16.7.1.1.3	INTEGER	read-only	Relative to the chassis, the current operating status of the system in the slot.
GAU slotSecondsSinceReset	1.3.6.1.4.1.33.16.7.1.1.4	Gauge	read-only	The number of seconds since the system in the slot was last reset by hardware or software.
HAR slotHardwareType	1.3.6.1.4.1.33.16.7.1.1.5	HardwareType	read-only	The type of hardware in the slot.
SER slotHardwareSerialNumber	1.3.6.1.4.1.33.16.7.1.1.6	SerialNumber	read-only	The ITouch serial number of the function card hardware in this slot.
INT slotHardwareRevision	1.3.6.1.4.1.33.16.7.1.1.7	INTEGER	read-only	This revision level of the function card hardware in the slot.
IOT slotIOCardType	1.3.6.1.4.1.33.16.7.1.1.8	IOType	read-only	The hardware type of the I/O card in this slot.
SER slotIOCardSerialNumber	1.3.6.1.4.1.33.16.7.1.1.9	SerialNumber	read-only	The ITouch serial number of the I/O card in this slot.
INT slotIOCardOperStatus	1.3.6.1.4.1.33.16.7.1.1.10	INTEGER	read-only	Status of the I/O card relative to the function card in this slot.
INT slotBootstrapFirmwareRevision	1.3.6.1.4.1.33.16.7.1.1.11	INTEGER	read-only	The firmware revision level of the bootstrap ROM installed in the system in the slot.
INT slotElementalFirmwareRevision	1.3.6.1.4.1.33.16.7.1.1.12	INTEGER	read-only	The firmware revision level of the minimal function ROM (management bus microprocessor) installed in the system in the slot.
INT slotMemorySize	1.3.6.1.4.1.33.16.7.1.1.13	INTEGER	read-only	The number of bytes of memory installed in the system in the slot.
GAU slotLedNumber	1.3.6.1.4.1.33.16.7.1.1.14	Gauge	read-only	The number of LEDs on the system in the slot. A value of 0 indicates none, unknown, or status not readable.
OCT slotLedStatus	1.3.6.1.4.1.33.16.7.1.1.15	OCTET STRING	read-only	The status of the LEDs displayed on the front and back of the system in the slot. The first bit is the high-order bit of the first byte of the value, proceeding to the low-order bit, then to then next byte. On the system hardware, the first LED is at the top, left, front, proceeding left to right, top to bottom, and front to back.
MAC slotBase802Address	1.3.6.1.4.1.33.16.7.1.1.16	MacAddress	read-only	Base IEEE 802 global address for the slot.
IP slotIpAddress	1.3.6.1.4.1.33.16.7.1.1.17	IpAddress	read-only	An internet address to which the system in this slot might respond. May be one of many.
INT slotPlus5Status	1.3.6.1.4.1.33.16.7.1.1.18	INTEGER	read-only	Status of the +5 volt power to the slot.
INT slotPlus12Status	1.3.6.1.4.1.33.16.7.1.1.19	INTEGER	read-only	Status of the +12 volt power to the slot.
INT slotMinus12Status	1.3.6.1.4.1.33.16.7.1.1.20	INTEGER	read-only	Status of the -12 volt power to the slot.
GAU slotPlus5Watts	1.3.6.1.4.1.33.16.7.1.1.21	Gauge	read-only	Tenths of watts of +5 volt power currently drawn by the slot.
GAU slotPlus12Watts	1.3.6.1.4.1.33.16.7.1.1.22	Gauge	read-only	Tenths of watts of +12 volt power currently drawn by the slot.
GAU slotMinus12Watts	1.3.6.1.4.1.33.16.7.1.1.23	Gauge	read-only	Tenths of watts of -12 volt power currently drawn by the slot.
INT slotIOCardHardwareVersion	1.3.6.1.4.1.33.16.7.1.1.24	INTEGER	read-only	Version number of I/O card in the slot.
INT slotRestoreNVS	1.3.6.1.4.1.33.16.7.1.1.25	INTEGER	read-write	Setting to 'execute' causes the non-volatile parameter storage to be restored from an installed memory card. Setting to 'ready' has no effect.
INT slotDefaultNVS	1.3.6.1.4.1.33.16.7.1.1.26	INTEGER	read-write	Setting to 'execute' causes non-volatile stored parameters to be reset to factory defaults. Setting to 'ready' has no effect.
slotBootTable	1.3.6.1.4.1.33.16.7.2		not-accessible	A list of slot bootstrap status entries. A given slot has an entry in this table only when slotOperStatus is one of: loadRequested, loading, dumpRequested, dumping, paramRequested, paramLoading
slotBootEntry	1.3.6.1.4.1.33.16.7.2.1		not-accessible	Bootstrap status values for a chassis slot.
INT slotBootIndex	1.3.6.1.4.1.33.16.7.2.1.1	INTEGER	read-only	An index value that uniquely identifies a slot, defined the same as slotIndex.
INT slotBootIfIndex	1.3.6.1.4.1.33.16.7.2.1.2	INTEGER	read-only	An index value that uniquely identifies the interface in use for bootstrap functions. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
OID slotBootNetwork	1.3.6.1.4.1.33.16.7.2.1.3	OBJECT IDENTIFIER	read-only	The instance identifier of the first object in the conceptual row entry for the segment or port this interface is using, that is, segmentType or portType.
INT slotBootProtocol	1.3.6.1.4.1.33.16.7.2.1.4	INTEGER	read-only	The protocol in use for bootstrap operation.
MAC slotBoot802Address	1.3.6.1.4.1.33.16.7.2.1.5	MacAddress	read-only	IEEE 802 global address in use for bootstrap operation.
ADR slotBootAddressType	1.3.6.1.4.1.33.16.7.2.1.6	AddressType	read-only	The type of network address contained in slotBootAddress.
OCT slotBootAddress	1.3.6.1.4.1.33.16.7.2.1.7	OCTET STRING	read-only	The network address the system in the slot is using to identify itself for bootstrap operation.
ADR slotBootServerAddressType	1.3.6.1.4.1.33.16.7.2.1.8	AddressType	read-only	The type of network address contained in slotBootServerAddress.
OCT slotBootServerAddress	1.3.6.1.4.1.33.16.7.2.1.9	OCTET STRING	read-only	The network address of the system supplying bootstrap services to the system in the slot.
IP slotBootGatewayAddress	1.3.6.1.4.1.33.16.7.2.1.10	IpAddress	read-only	The internet address of the router in use for bootstrap operation.
STR slotBootFileName	1.3.6.1.4.1.33.16.7.2.1.11	DisplayString	read-only	The full name of the file in use for bootstrap operation.
GAU slotBootBlockNumber	1.3.6.1.4.1.33.16.7.2.1.12	Gauge	read-only	The current block number being transferred for bootstrap operation, zero if unknown or not applicable.
OCT slotBootCrashCode	1.3.6.1.4.1.33.16.7.2.1.13	OCTET STRING	read-only	If slotOperStatus is dumpRequested or dumping, a code number to identify the crash reason; otherwise zero length.
slotControllerTable	1.3.6.1.4.1.33.16.7.3		not-accessible	A list of controller entries, one for each controller of each type in each slot.
slotControllerEntry	1.3.6.1.4.1.33.16.7.3.1		not-accessible	Values for a controller.
NET slotControllerType	1.3.6.1.4.1.33.16.7.3.1.1	NetworkType	read-only	The controller type.
INT slotControllerIndex	1.3.6.1.4.1.33.16.7.3.1.2	INTEGER	read-only	An index value that uniquely identifies a controller.
OID slotControllerNetwork	1.3.6.1.4.1.33.16.7.3.1.3	OBJECT IDENTIFIER	read-only	The instance identifier of the first object in the conceptual row entry for the segment or port this controller is to use, that is, segmentType or portType.
xPowerSupply	1.3.6.1.4.1.33.16.8
powerSupplyTable	1.3.6.1.4.1.33.16.8.1		not-accessible	A list of power supply entries.
powerSupplyEntry	1.3.6.1.4.1.33.16.8.1.1		not-accessible	Values for a chassis power supply.
INT powerSupplyIndex	1.3.6.1.4.1.33.16.8.1.1.1	INTEGER	read-only	An index value that uniquely identifies a power supply, in the range 1 to the number of power supply slots in the chassis.
INT powerSupplyAdminAction	1.3.6.1.4.1.33.16.8.1.1.2	INTEGER	read-write	Control to cause reset of the power supply. When read, the value is always 'ready'. Setting to 'reset' or 'resetHold' causes a single attempt to take that action, but does not ensure transition to any particular value of powerSupplyRedundancyStatus.
INT powerSupplyFirmwareVersion	1.3.6.1.4.1.33.16.8.1.1.3	INTEGER	read-only	Version number of power supply firmware.
INT powerSupplyRedundancyStatus	1.3.6.1.4.1.33.16.8.1.1.4	INTEGER	read-only	The current redundancy status of the power supply.
INT powerSupplyPlus5Status	1.3.6.1.4.1.33.16.8.1.1.5	INTEGER	read-only	Status of the +5 volt power from the power supply.
INT powerSupplyPlus12Status	1.3.6.1.4.1.33.16.8.1.1.6	INTEGER	read-only	Status of the +12 volt power from the power supply.
INT powerSupplyMinus12Status	1.3.6.1.4.1.33.16.8.1.1.7	INTEGER	read-only	Status of the -12 volt power from the power supply.
INT powerSupplyThermalWarningStatus	1.3.6.1.4.1.33.16.8.1.1.8	INTEGER	read-only	The current thermal warning status of the power supply.
INT powerSupplyThermalShutdownStatus	1.3.6.1.4.1.33.16.8.1.1.9	INTEGER	read-only	The current thermal shutdown status of the power supply.
INT powerSupplyFanStatus	1.3.6.1.4.1.33.16.8.1.1.10	INTEGER	read-only	The current status of the power supply's fan.
INT powerSupplyHardwareInhibitStatus	1.3.6.1.4.1.33.16.8.1.1.11	INTEGER	read-only	The current status of the power supply's hardware inhibit.
INT powerSupplyPlus5History	1.3.6.1.4.1.33.16.8.1.1.12	INTEGER	read-only	History of the +5 volt power from the power supply.
INT powerSupplyPlus12History	1.3.6.1.4.1.33.16.8.1.1.13	INTEGER	read-only	History of the +12 volt power from the power supply.
INT powerSupplyMinus12History	1.3.6.1.4.1.33.16.8.1.1.14	INTEGER	read-only	History of the -12 volt power from the power supply.
INT powerSupplyThermalWarningHistory	1.3.6.1.4.1.33.16.8.1.1.15	INTEGER	read-only	The thermal warning history of the power supply.
INT powerSupplyThermalShutdownHistory	1.3.6.1.4.1.33.16.8.1.1.16	INTEGER	read-only	The thermal shutdown history of the power supply.
INT powerSupplyFanHistory	1.3.6.1.4.1.33.16.8.1.1.17	INTEGER	read-only	The status history of the power supply's fan.
INT powerSupplyHardwareInhibitHistory	1.3.6.1.4.1.33.16.8.1.1.18	INTEGER	read-only	The status history of the power supply's hardware inhibit.
GAU powerSupplyPlus5Volts	1.3.6.1.4.1.33.16.8.1.1.19	Gauge	read-only	In hundredths, volts of +5 volt power currently provided by the power supply. A value of 0 indicates unknown.
GAU powerSupplyPlus12Volts	1.3.6.1.4.1.33.16.8.1.1.20	Gauge	read-only	In hundredths, volts of +12 volt power currently provided by the power supply. A value of 0 indicates unknown.
GAU powerSupplyMinus12Volts	1.3.6.1.4.1.33.16.8.1.1.21	Gauge	read-only	In hundredths, volts of -12 volt power currently provided by the power supply. A value of 0 indicates unknown.
GAU powerSupplyWatts	1.3.6.1.4.1.33.16.8.1.1.22	Gauge	read-only	Watts of power currently drawn from this power supply. A value of 0 indicates unknown.
GAU powerSupplyWattsMax	1.3.6.1.4.1.33.16.8.1.1.23	Gauge	read-only	Maximum watts of power available from this power supply. A value of 0 indicates unknown.
GAU powerSupplyChassisWatts	1.3.6.1.4.1.33.16.8.1.1.24	Gauge	read-only	Total watts of power currently drawn by the entire chassis. A value of 0 indicates unknown.
GAU powerSupplyChassisWattsMax	1.3.6.1.4.1.33.16.8.1.1.25	Gauge	read-only	Total maximum watts of power available from all the power supplies in the chassis. A value of 0 indicates unknown.
INT powerSupplyHardwareType	1.3.6.1.4.1.33.16.8.1.1.26	INTEGER	read-only	The type of power supply.
xFirmwareUpdate	1.3.6.1.4.1.33.16.9
firmwareUpdateTable	1.3.6.1.4.1.33.16.9.1		not-accessible	Table of descriptive and status information concerning the writing of firmware to a target I/O card.
firmwareUpdateEntry	1.3.6.1.4.1.33.16.9.1.1		not-accessible	An entry in the table concerning the writing of firmware to a target I/O card.
INT firmwareUpdateSlotIndex	1.3.6.1.4.1.33.16.9.1.1.1	INTEGER	read-only	This variable identifies the slot to which is to be the target of the firmware update.
STR firmwareUpdateDefaultFileName	1.3.6.1.4.1.33.16.9.1.1.2	DisplayString	read-only	This variable when read will obtain the default file name from the target.
STR firmwareUpdateFileName	1.3.6.1.4.1.33.16.9.1.1.3	DisplayString	read-write	This variable contains the name of the file to be read from the flash memory card and written to the target.
INT firmwareUpdateStatus	1.3.6.1.4.1.33.16.9.1.1.4	INTEGER	read-write	This variable is used to start the update process. The agent always 'ready' for this value. Setting this value to 'execute' causes the agent to write the file specified by firmwareUpdateFileName to be written to the taget. Setting this value to 'execute' when firmwareUpdateFileName has not been written or when firmwareUpdateState is 'writing' causes bad value to be returned.
INT firmwareUpdateState	1.3.6.1.4.1.33.16.9.1.1.5	INTEGER	read-only	This variable indicates the current state of firmware update, 'idle' indicates that firmware update may be initiated, and 'writing' indicates that an update is in process.
INT firmwareUpdateCompletionStatus	1.3.6.1.4.1.33.16.9.1.1.6	INTEGER	read-only	This variable indicates the completion status of the the last firmware update attempt. 'none' indicates that no firmware update has yet been attempted.
INT firmwareUpdateMethod	1.3.6.1.4.1.33.16.9.1.1.7	INTEGER	read-write	This variable indicates the method of update of the firmware update attempt.

AddressType (2)
ADR slotBootAddressType	1.3.6.1.4.1.33.16.7.2.1.6	AddressType	read-only	The type of network address contained in slotBootAddress.
ADR slotBootServerAddressType	1.3.6.1.4.1.33.16.7.2.1.8	AddressType	read-only	The type of network address contained in slotBootServerAddress.
Counter (1)
CTR slotBootControlStorageFailures	1.3.6.1.4.1.33.16.6.3.1.4	Counter	read-only	The number of times a read from or write to a given Storage location failed
DisplayString (6)
STR firmwareUpdateDefaultFileName	1.3.6.1.4.1.33.16.9.1.1.2	DisplayString	read-only	This variable when read will obtain the default file name from the target.
STR firmwareUpdateFileName	1.3.6.1.4.1.33.16.9.1.1.3	DisplayString	read-write	This variable contains the name of the file to be read from the flash memory card and written to the target.
STR slotBootControlInternetDelimiter	1.3.6.1.4.1.33.16.6.1.1.11	DisplayString	read-write	The character separating the load file directory name from the file name.
STR slotBootControlInternetFile	1.3.6.1.4.1.33.16.6.1.1.7	DisplayString	read-write	The filename to request when loading an image via TFTP.
STR slotBootControlMopFile	1.3.6.1.4.1.33.16.6.1.1.6	DisplayString	read-write	The software file name to request for down-line load of the server via MOP or XMOP.
STR slotBootFileName	1.3.6.1.4.1.33.16.7.2.1.11	DisplayString	read-only	The full name of the file in use for bootstrap operation.
Gauge (13)
GAU powerSupplyChassisWatts	1.3.6.1.4.1.33.16.8.1.1.24	Gauge	read-only	Total watts of power currently drawn by the entire chassis. A value of 0 indicates unknown.
GAU powerSupplyChassisWattsMax	1.3.6.1.4.1.33.16.8.1.1.25	Gauge	read-only	Total maximum watts of power available from all the power supplies in the chassis. A value of 0 indicates unknown.
GAU powerSupplyMinus12Volts	1.3.6.1.4.1.33.16.8.1.1.21	Gauge	read-only	In hundredths, volts of -12 volt power currently provided by the power supply. A value of 0 indicates unknown.
GAU powerSupplyPlus12Volts	1.3.6.1.4.1.33.16.8.1.1.20	Gauge	read-only	In hundredths, volts of +12 volt power currently provided by the power supply. A value of 0 indicates unknown.
GAU powerSupplyPlus5Volts	1.3.6.1.4.1.33.16.8.1.1.19	Gauge	read-only	In hundredths, volts of +5 volt power currently provided by the power supply. A value of 0 indicates unknown.
GAU powerSupplyWatts	1.3.6.1.4.1.33.16.8.1.1.22	Gauge	read-only	Watts of power currently drawn from this power supply. A value of 0 indicates unknown.
GAU powerSupplyWattsMax	1.3.6.1.4.1.33.16.8.1.1.23	Gauge	read-only	Maximum watts of power available from this power supply. A value of 0 indicates unknown.
GAU slotBootBlockNumber	1.3.6.1.4.1.33.16.7.2.1.12	Gauge	read-only	The current block number being transferred for bootstrap operation, zero if unknown or not applicable.
GAU slotLedNumber	1.3.6.1.4.1.33.16.7.1.1.14	Gauge	read-only	The number of LEDs on the system in the slot. A value of 0 indicates none, unknown, or status not readable.
GAU slotMinus12Watts	1.3.6.1.4.1.33.16.7.1.1.23	Gauge	read-only	Tenths of watts of -12 volt power currently drawn by the slot.
GAU slotPlus12Watts	1.3.6.1.4.1.33.16.7.1.1.22	Gauge	read-only	Tenths of watts of +12 volt power currently drawn by the slot.
GAU slotPlus5Watts	1.3.6.1.4.1.33.16.7.1.1.21	Gauge	read-only	Tenths of watts of +5 volt power currently drawn by the slot.
GAU slotSecondsSinceReset	1.3.6.1.4.1.33.16.7.1.1.4	Gauge	read-only	The number of seconds since the system in the slot was last reset by hardware or software.
HardwareType (1)
HAR slotHardwareType	1.3.6.1.4.1.33.16.7.1.1.5	HardwareType	read-only	The type of hardware in the slot.
INTEGER (72)
INT basicSlot	1.3.6.1.4.1.33.16.1.2	INTEGER	read-only	Chassis slot number (slotIndex) of the system whose agent is supplying this MIB.
INT basicSlotNumber	1.3.6.1.4.1.33.16.1.3	INTEGER	read-only	Number of slots in the chassis.
INT controllerIndex	1.3.6.1.4.1.33.16.4.1.1.2	INTEGER	read-only	An index value that uniquely identifies a controller.
INT firmwareUpdateCompletionStatus	1.3.6.1.4.1.33.16.9.1.1.6	INTEGER	read-only	This variable indicates the completion status of the the last firmware update attempt. 'none' indicates that no firmware update has yet been attempted.
INT firmwareUpdateMethod	1.3.6.1.4.1.33.16.9.1.1.7	INTEGER	read-write	This variable indicates the method of update of the firmware update attempt.
INT firmwareUpdateSlotIndex	1.3.6.1.4.1.33.16.9.1.1.1	INTEGER	read-only	This variable identifies the slot to which is to be the target of the firmware update.
INT firmwareUpdateState	1.3.6.1.4.1.33.16.9.1.1.5	INTEGER	read-only	This variable indicates the current state of firmware update, 'idle' indicates that firmware update may be initiated, and 'writing' indicates that an update is in process.
INT firmwareUpdateStatus	1.3.6.1.4.1.33.16.9.1.1.4	INTEGER	read-write	This variable is used to start the update process. The agent always 'ready' for this value. Setting this value to 'execute' causes the agent to write the file specified by firmwareUpdateFileName to be written to the taget. Setting this value to 'execute' when firmwareUpdateFileName has not been written or when firmwareUpdateState is 'writing' causes bad value to be returned.
INT interfaceIndex	1.3.6.1.4.1.33.16.5.1.1.1	INTEGER	read-only	An index value that uniquely identifies an interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
INT portIndex	1.3.6.1.4.1.33.16.3.4.1.2	INTEGER	read-only	An index value that uniquely identifies a port.
INT portIOCardOperStatus	1.3.6.1.4.1.33.16.3.3	INTEGER	read-only	Status of the I/O card relative to the function card in this slot.
INT powerSupplyAdminAction	1.3.6.1.4.1.33.16.8.1.1.2	INTEGER	read-write	Control to cause reset of the power supply. When read, the value is always 'ready'. Setting to 'reset' or 'resetHold' causes a single attempt to take that action, but does not ensure transition to any particular value of powerSupplyRedundancyStatus.
INT powerSupplyFanHistory	1.3.6.1.4.1.33.16.8.1.1.17	INTEGER	read-only	The status history of the power supply's fan.
INT powerSupplyFanStatus	1.3.6.1.4.1.33.16.8.1.1.10	INTEGER	read-only	The current status of the power supply's fan.
INT powerSupplyFirmwareVersion	1.3.6.1.4.1.33.16.8.1.1.3	INTEGER	read-only	Version number of power supply firmware.
INT powerSupplyHardwareInhibitHistory	1.3.6.1.4.1.33.16.8.1.1.18	INTEGER	read-only	The status history of the power supply's hardware inhibit.
INT powerSupplyHardwareInhibitStatus	1.3.6.1.4.1.33.16.8.1.1.11	INTEGER	read-only	The current status of the power supply's hardware inhibit.
INT powerSupplyHardwareType	1.3.6.1.4.1.33.16.8.1.1.26	INTEGER	read-only	The type of power supply.
INT powerSupplyIndex	1.3.6.1.4.1.33.16.8.1.1.1	INTEGER	read-only	An index value that uniquely identifies a power supply, in the range 1 to the number of power supply slots in the chassis.
INT powerSupplyMinus12History	1.3.6.1.4.1.33.16.8.1.1.14	INTEGER	read-only	History of the -12 volt power from the power supply.
INT powerSupplyMinus12Status	1.3.6.1.4.1.33.16.8.1.1.7	INTEGER	read-only	Status of the -12 volt power from the power supply.
INT powerSupplyPlus12History	1.3.6.1.4.1.33.16.8.1.1.13	INTEGER	read-only	History of the +12 volt power from the power supply.
INT powerSupplyPlus12Status	1.3.6.1.4.1.33.16.8.1.1.6	INTEGER	read-only	Status of the +12 volt power from the power supply.
INT powerSupplyPlus5History	1.3.6.1.4.1.33.16.8.1.1.12	INTEGER	read-only	History of the +5 volt power from the power supply.
INT powerSupplyPlus5Status	1.3.6.1.4.1.33.16.8.1.1.5	INTEGER	read-only	Status of the +5 volt power from the power supply.
INT powerSupplyRedundancyStatus	1.3.6.1.4.1.33.16.8.1.1.4	INTEGER	read-only	The current redundancy status of the power supply.
INT powerSupplyThermalShutdownHistory	1.3.6.1.4.1.33.16.8.1.1.16	INTEGER	read-only	The thermal shutdown history of the power supply.
INT powerSupplyThermalShutdownStatus	1.3.6.1.4.1.33.16.8.1.1.9	INTEGER	read-only	The current thermal shutdown status of the power supply.
INT powerSupplyThermalWarningHistory	1.3.6.1.4.1.33.16.8.1.1.15	INTEGER	read-only	The thermal warning history of the power supply.
INT powerSupplyThermalWarningStatus	1.3.6.1.4.1.33.16.8.1.1.8	INTEGER	read-only	The current thermal warning status of the power supply.
INT slotAdminAction	1.3.6.1.4.1.33.16.7.1.1.2	INTEGER	read-write	Control to cause reset of the system in a slot. When read, the value is always 'ready'. Setting to 'reset' or 'resetHold' causes a single attempt to take that action, but does not ensure transition to any particular value of slotOperStatus.
INT slotBootControlFlagDumpBootpTftp	1.3.6.1.4.1.33.16.6.2.1.3	INTEGER	read-write	Control for performing dump over BOOTP/TFTP.
INT slotBootControlFlagDumpLocal	1.3.6.1.4.1.33.16.6.2.1.9	INTEGER	read-write	Control for performing dump from a local device.
INT slotBootControlFlagDumpMop	1.3.6.1.4.1.33.16.6.2.1.12	INTEGER	read-write	Control for performing dump over Digital's MOP.
INT slotBootControlFlagDumpRarpTftp	1.3.6.1.4.1.33.16.6.2.1.18	INTEGER	read-write	Control for performing dump over RARP/TFTP.
INT slotBootControlFlagDumpTftpDirect	1.3.6.1.4.1.33.16.6.2.1.6	INTEGER	read-write	Control for performing dump over direct TFTP.
INT slotBootControlFlagDumpXmop	1.3.6.1.4.1.33.16.6.2.1.15	INTEGER	read-write	Control for performing dump over ITouch extended MOP.
INT slotBootControlFlagLoadBootpTftp	1.3.6.1.4.1.33.16.6.2.1.1	INTEGER	read-write	Control for performing load over BOOTP/TFTP.
INT slotBootControlFlagLoadLocal	1.3.6.1.4.1.33.16.6.2.1.7	INTEGER	read-write	Control for performing load from a local device.
INT slotBootControlFlagLoadMop	1.3.6.1.4.1.33.16.6.2.1.10	INTEGER	read-write	Control for performing load over Digital's MOP.
INT slotBootControlFlagLoadRarpTftp	1.3.6.1.4.1.33.16.6.2.1.16	INTEGER	read-write	Control for performing load over RARP/TFTP.
INT slotBootControlFlagLoadTftpDirect	1.3.6.1.4.1.33.16.6.2.1.4	INTEGER	read-write	Control for performing load over direct TFTP.
INT slotBootControlFlagLoadXmop	1.3.6.1.4.1.33.16.6.2.1.13	INTEGER	read-write	Control for performing load over ITouch extended MOP.
INT slotBootControlFlagParamBootpTftp	1.3.6.1.4.1.33.16.6.2.1.2	INTEGER	read-write	Control for performing parameter load over BOOTP/TFTP.
INT slotBootControlFlagParamLocal	1.3.6.1.4.1.33.16.6.2.1.8	INTEGER	read-write	Control for performing parameter load from a local device.
INT slotBootControlFlagParamMop	1.3.6.1.4.1.33.16.6.2.1.11	INTEGER	read-write	Control for performing parameter load over Digital's MOP.
INT slotBootControlFlagParamRarpTftp	1.3.6.1.4.1.33.16.6.2.1.17	INTEGER	read-write	Control for performing parameter load over RARP/TFTP.
INT slotBootControlFlagParamTftpDirect	1.3.6.1.4.1.33.16.6.2.1.5	INTEGER	read-write	Control for performing parameter load over direct TFTP.
INT slotBootControlFlagParamXmop	1.3.6.1.4.1.33.16.6.2.1.14	INTEGER	read-write	Control for performing parameter load over ITouch extended MOP.
INT slotBootControlIndex	1.3.6.1.4.1.33.16.6.1.1.2	INTEGER	read-only	An index value that uniquely identifies a boot control entry, from 1 to the number of entries for the slot.
INT slotBootControlSlot	1.3.6.1.4.1.33.16.6.1.1.1	INTEGER	read-only	An index value that uniquely identifies a slot, defined the same as slotIndex.
INT slotBootControlStatus	1.3.6.1.4.1.33.16.6.1.1.3	INTEGER	read-write	The status of the entry. Set to 'disabled' to disable the entry.
INT slotBootControlStorageClientSlot	1.3.6.1.4.1.33.16.6.3.1.1	INTEGER	read-only	An index value that uniquely identifies a slot, defined the same as slotIndex.
INT slotBootControlStorageServerSlot	1.3.6.1.4.1.33.16.6.3.1.2	INTEGER	read-only	An index value that uniquely identifies the slot in which the Storage record resides, with the same values as slotIndex.
INT slotBootControlStorageStatus	1.3.6.1.4.1.33.16.6.3.1.3	INTEGER	read-only	The status of the entry.
INT slotBootIfIndex	1.3.6.1.4.1.33.16.7.2.1.2	INTEGER	read-only	An index value that uniquely identifies the interface in use for bootstrap functions. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
INT slotBootIndex	1.3.6.1.4.1.33.16.7.2.1.1	INTEGER	read-only	An index value that uniquely identifies a slot, defined the same as slotIndex.
INT slotBootProtocol	1.3.6.1.4.1.33.16.7.2.1.4	INTEGER	read-only	The protocol in use for bootstrap operation.
INT slotBootstrapFirmwareRevision	1.3.6.1.4.1.33.16.7.1.1.11	INTEGER	read-only	The firmware revision level of the bootstrap ROM installed in the system in the slot.
INT slotControllerIndex	1.3.6.1.4.1.33.16.7.3.1.2	INTEGER	read-only	An index value that uniquely identifies a controller.
INT slotDefaultNVS	1.3.6.1.4.1.33.16.7.1.1.26	INTEGER	read-write	Setting to 'execute' causes non-volatile stored parameters to be reset to factory defaults. Setting to 'ready' has no effect.
INT slotElementalFirmwareRevision	1.3.6.1.4.1.33.16.7.1.1.12	INTEGER	read-only	The firmware revision level of the minimal function ROM (management bus microprocessor) installed in the system in the slot.
INT slotHardwareRevision	1.3.6.1.4.1.33.16.7.1.1.7	INTEGER	read-only	This revision level of the function card hardware in the slot.
INT slotIndex	1.3.6.1.4.1.33.16.7.1.1.1	INTEGER	read-only	An index value that uniquely identifies a slot, in the range 0 to basicSlotNumber, where the value 0 indicates the same slot as basicSlot. As the objects found at instance zero are duplicates, that instance does not appear in responses a get-next, that is, the lowest numbered slotIndex returned by get-next is 1.
INT slotIOCardHardwareVersion	1.3.6.1.4.1.33.16.7.1.1.24	INTEGER	read-only	Version number of I/O card in the slot.
INT slotIOCardOperStatus	1.3.6.1.4.1.33.16.7.1.1.10	INTEGER	read-only	Status of the I/O card relative to the function card in this slot.
INT slotMemorySize	1.3.6.1.4.1.33.16.7.1.1.13	INTEGER	read-only	The number of bytes of memory installed in the system in the slot.
INT slotMinus12Status	1.3.6.1.4.1.33.16.7.1.1.20	INTEGER	read-only	Status of the -12 volt power to the slot.
INT slotOperStatus	1.3.6.1.4.1.33.16.7.1.1.3	INTEGER	read-only	Relative to the chassis, the current operating status of the system in the slot.
INT slotPlus12Status	1.3.6.1.4.1.33.16.7.1.1.19	INTEGER	read-only	Status of the +12 volt power to the slot.
INT slotPlus5Status	1.3.6.1.4.1.33.16.7.1.1.18	INTEGER	read-only	Status of the +5 volt power to the slot.
INT slotRestoreNVS	1.3.6.1.4.1.33.16.7.1.1.25	INTEGER	read-write	Setting to 'execute' causes the non-volatile parameter storage to be restored from an installed memory card. Setting to 'ready' has no effect.
IOType (2)
IOT portIOCardType	1.3.6.1.4.1.33.16.3.1	IOType	read-only	The hardware type of the I/O card in this slot.
IOT slotIOCardType	1.3.6.1.4.1.33.16.7.1.1.8	IOType	read-only	The hardware type of the I/O card in this slot.
IpAddress (5)
IP slotBootControlInternetAddress	1.3.6.1.4.1.33.16.6.1.1.8	IpAddress	read-write	The internet address of the system is to use for itself when loading via TFTP. The value 0.0.0.0 indicates default action.
IP slotBootControlInternetGateway	1.3.6.1.4.1.33.16.6.1.1.10	IpAddress	read-write	The internet address of the gateway to use when loading an image via TFTP. The value 0.0.0.0 indicates default action.
IP slotBootControlInternetServer	1.3.6.1.4.1.33.16.6.1.1.9	IpAddress	read-write	The internet address of the server to use when loading an image via TFTP. The value 0.0.0.0 indicates default action.
IP slotBootGatewayAddress	1.3.6.1.4.1.33.16.7.2.1.10	IpAddress	read-only	The internet address of the router in use for bootstrap operation.
IP slotIpAddress	1.3.6.1.4.1.33.16.7.1.1.17	IpAddress	read-only	An internet address to which the system in this slot might respond. May be one of many.
Letter (1)
LET segmentIndex	1.3.6.1.4.1.33.16.2.1.1.2	Letter	read-only	An index value that uniquely identifies a segment.
MacAddress (4)
MAC basicBase802Address	1.3.6.1.4.1.33.16.1.1	MacAddress	read-only	Base IEEE 802 global address for the chassis.
MAC basicNewBase802Address	1.3.6.1.4.1.33.16.1.4	MacAddress	read-write	New base IEEE 802 global address for the chassis. Must be set in conjunction with featType 'changeEthernetAddress' and featKey from the ITouch System MIB.
MAC slotBase802Address	1.3.6.1.4.1.33.16.7.1.1.16	MacAddress	read-only	Base IEEE 802 global address for the slot.
MAC slotBoot802Address	1.3.6.1.4.1.33.16.7.2.1.5	MacAddress	read-only	IEEE 802 global address in use for bootstrap operation.
NetworkType (4)
NET controllerType	1.3.6.1.4.1.33.16.4.1.1.1	NetworkType	read-only	The controller type.
NET portType	1.3.6.1.4.1.33.16.3.4.1.1	NetworkType	read-only	The port type.
NET segmentType	1.3.6.1.4.1.33.16.2.1.1.1	NetworkType	read-only	The segment type.
NET slotControllerType	1.3.6.1.4.1.33.16.7.3.1.1	NetworkType	read-only	The controller type.
OBJECT IDENTIFIER (6)
OID controllerNetwork	1.3.6.1.4.1.33.16.4.1.1.3	OBJECT IDENTIFIER	read-write	The instance identifier of the first object in the conceptual row entry for the segment, port, or controller this controller is to use, that is, segmentType, portType or controllerType.
OID interfaceNetwork	1.3.6.1.4.1.33.16.5.1.1.2	OBJECT IDENTIFIER	read-write	The instance identifier of the first object in the conceptual row entry for the segment, port, or controller this interface is to use, that is, segmentType, portType, or controllerType.
OID slotBootControlController	1.3.6.1.4.1.33.16.6.1.1.4	OBJECT IDENTIFIER	read-write	The instance identifier of the first object in the conceptual row entry for the controller this entry selects for bootstrap operation, that is, controllerType. This entry must be compatible with slotBootControlNetwork, including being of the same network type. The value 0.0 indicates default action.
OID slotBootControlNetwork	1.3.6.1.4.1.33.16.6.1.1.5	OBJECT IDENTIFIER	read-write	The instance identifier of the first object in the conceptual row entry for the segment or port this entry selects for bootstrap operation, that is, segmentType or portType. This entry must be compatible with slotBootControlController, including being of the same network type. The value 0.0 indicates default action.
OID slotBootNetwork	1.3.6.1.4.1.33.16.7.2.1.3	OBJECT IDENTIFIER	read-only	The instance identifier of the first object in the conceptual row entry for the segment or port this interface is using, that is, segmentType or portType.
OID slotControllerNetwork	1.3.6.1.4.1.33.16.7.3.1.3	OBJECT IDENTIFIER	read-only	The instance identifier of the first object in the conceptual row entry for the segment or port this controller is to use, that is, segmentType or portType.
OCTET STRING (4)
OCT slotBootAddress	1.3.6.1.4.1.33.16.7.2.1.7	OCTET STRING	read-only	The network address the system in the slot is using to identify itself for bootstrap operation.
OCT slotBootCrashCode	1.3.6.1.4.1.33.16.7.2.1.13	OCTET STRING	read-only	If slotOperStatus is dumpRequested or dumping, a code number to identify the crash reason; otherwise zero length.
OCT slotBootServerAddress	1.3.6.1.4.1.33.16.7.2.1.9	OCTET STRING	read-only	The network address of the system supplying bootstrap services to the system in the slot.
OCT slotLedStatus	1.3.6.1.4.1.33.16.7.1.1.15	OCTET STRING	read-only	The status of the LEDs displayed on the front and back of the system in the slot. The first bit is the high-order bit of the first byte of the value, proceeding to the low-order bit, then to then next byte. On the system hardware, the first LED is at the top, left, front, proceeding left to right, top to bottom, and front to back.
SerialNumber (3)
SER portIOCardSerialNumber	1.3.6.1.4.1.33.16.3.2	SerialNumber	read-only	The ITouch serial number of the I/O card in this slot.
SER slotHardwareSerialNumber	1.3.6.1.4.1.33.16.7.1.1.6	SerialNumber	read-only	The ITouch serial number of the function card hardware in this slot.
SER slotIOCardSerialNumber	1.3.6.1.4.1.33.16.7.1.1.9	SerialNumber	read-only	The ITouch serial number of the I/O card in this slot.
No type (34)
controllerEntry	1.3.6.1.4.1.33.16.4.1.1		not-accessible	Values for a controller.
controllerTable	1.3.6.1.4.1.33.16.4.1		not-accessible	A list of controller entries, one for each controller of each type on the local system.
firmwareUpdateEntry	1.3.6.1.4.1.33.16.9.1.1		not-accessible	An entry in the table concerning the writing of firmware to a target I/O card.
firmwareUpdateTable	1.3.6.1.4.1.33.16.9.1		not-accessible	Table of descriptive and status information concerning the writing of firmware to a target I/O card.
interfaceEntry	1.3.6.1.4.1.33.16.5.1.1		not-accessible	Values for an interface.
interfaceTable	1.3.6.1.4.1.33.16.5.1		not-accessible	A list of interface entries, corresponding to the MIB II Interface group. These are directly equivalent to hardware network controllers, and must be the lowest numbered interfaces on the system.
portEntry	1.3.6.1.4.1.33.16.3.4.1		not-accessible	Values for an I/O card port.
portTable	1.3.6.1.4.1.33.16.3.4		not-accessible	A list of port entries, one for each port of each type on the slots I/O card.
powerSupplyEntry	1.3.6.1.4.1.33.16.8.1.1		not-accessible	Values for a chassis power supply.
powerSupplyTable	1.3.6.1.4.1.33.16.8.1		not-accessible	A list of power supply entries.
segmentEntry	1.3.6.1.4.1.33.16.2.1.1		not-accessible	Values for a chassis segment.
segmentTable	1.3.6.1.4.1.33.16.2.1		not-accessible	A list of segment entries, one for each segment of each type on the chassis.
slotBootControlEntry	1.3.6.1.4.1.33.16.6.1.1		not-accessible	Values for a chassis slot.
slotBootControlFlagEntry	1.3.6.1.4.1.33.16.6.2.1		not-accessible	Values for a boot control flag.
slotBootControlFlagTable	1.3.6.1.4.1.33.16.6.2		not-accessible	A list of slot boot control source flag entries.
slotBootControlStorageEntry	1.3.6.1.4.1.33.16.6.3.1		not-accessible	Values for a chassis slot.
slotBootControlStorageTable	1.3.6.1.4.1.33.16.6.3		not-accessible	A list of slot boot control Storage entries.
slotBootControlTable	1.3.6.1.4.1.33.16.6.1		not-accessible	A list of slot boot control entries.
slotBootEntry	1.3.6.1.4.1.33.16.7.2.1		not-accessible	Bootstrap status values for a chassis slot.
slotBootTable	1.3.6.1.4.1.33.16.7.2		not-accessible	A list of slot bootstrap status entries. A given slot has an entry in this table only when slotOperStatus is one of: loadRequested, loading, dumpRequested, dumping, paramRequested, paramLoading
slotControllerEntry	1.3.6.1.4.1.33.16.7.3.1		not-accessible	Values for a controller.
slotControllerTable	1.3.6.1.4.1.33.16.7.3		not-accessible	A list of controller entries, one for each controller of each type in each slot.
slotEntry	1.3.6.1.4.1.33.16.7.1.1		not-accessible	Values for a chassis slot.
slotTable	1.3.6.1.4.1.33.16.7.1		not-accessible	A list of slot entries.
xChassis	1.3.6.1.4.1.33.16
xChassisBasic	1.3.6.1.4.1.33.16.1
xController	1.3.6.1.4.1.33.16.4
xFirmwareUpdate	1.3.6.1.4.1.33.16.9
xInterface	1.3.6.1.4.1.33.16.5
xPort	1.3.6.1.4.1.33.16.3
xPowerSupply	1.3.6.1.4.1.33.16.8
xSegment	1.3.6.1.4.1.33.16.2
xSlot	1.3.6.1.4.1.33.16.7
xSlotBootControl	1.3.6.1.4.1.33.16.6

RFC description

iTouch Communications system chassis management including slots, controllers, and firmware updates.

Start monitoring iTouch Communications (later Black Box) modular chassis network equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ITOUCH-CHASSIS-MIB

This MIB depends on

Related MIBs

What Is ITOUCH-CHASSIS-MIB?

What Can Be Monitored

Supported Devices

Monitoring Examples

RFC description