IPX-RIP-PRIVATE-MIB

All MIBs › IPX-RIP-PRIVATE-MIB

Organization: Lucent's Concord Technology Center (CTC)

Last Updated: 1999-04-01

Category: Routing Protocols, Vendor: Lucent/Ascend

Description: Lucent/Avaya IPX RIP private MIB providing SNMP objects for IPX Routing Information Protocol neighbor and route table management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is IPX-RIP-PRIVATE-MIB?

IPX-RIP-PRIVATE-MIB (the Cajun IPX RIP Private MIB) is a Lucent/Avaya proprietary MIB for managing IPX Routing Information Protocol (RIP) neighbor and route information on Cajun-branded switching/routing equipment. It exposes objects describing IPX RIP neighbor relationships and the resulting route table entries learned via RIP. In a monitoring context it is used to confirm that IPX RIP neighbors are up and exchanging routes correctly, and that the learned route table reflects expected network topology, which is important for diagnosing IPX routing instability or neighbor loss. It is a vendor-proprietary extension layered conceptually on the generic IPX protocol MIB rather than a standard IETF module. It is typically deployed on Lucent/Avaya Cajun switches in legacy enterprise networks still running Novell IPX alongside RIP-based routing, where IPX-RIP-PRIVATE-MIB SNMP monitoring helps confirm neighbor and route state remain stable.

IPNetwork Monitor allows you to monitor SNMP objects defined in IPX-RIP-PRIVATE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Lucent/Avaya Cajun switch or router

Monitoring Examples

No object or table names were supplied for this module (sample_objects is empty), so a concrete polling scenario naming real objects cannot be honestly constructed. In general such a MIB would expose an IPX RIP neighbor table and a route table with hop-count/status fields, but no specific object names can be confirmed from the available data.

Imported Objects

From Cajun-ROOT

cjnProtocol

OBJECT-IDENTITY

From IPX-INTERFACE-MANAGEMENT-PRIVATE-MIB

cjnIpxIfIndex

OBJECT-TYPE

From IPX-PRIVATE-MIB

NetNumber

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

RowStatus

How to Use in IPNetwork Monitor

Example using cjnIpxRipIfStatTriggeredUpdatesSent OID:

Select a Lucent/Avaya Cajun switch/router (legacy IPX RIP) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type cjnIpxRipIfStatTriggeredUpdatesSent into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of RIP triggered updates sent on the interface. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
cjnIpxRip	1.3.6.1.4.1.1751.2.43.2.20			Cajun IPX RIP Private MIB
cjnIpxRipGlobalGroup	1.3.6.1.4.1.1751.2.43.2.20.1
INT cjnIpxRipEnabled	1.3.6.1.4.1.1751.2.43.2.20.1.1	INTEGER	read-write	Enable / Disable IPX RIP on this system.
cjnIpxRipFilterGroup	1.3.6.1.4.1.1751.2.43.2.20.2
cjnIpxRipFilterTable	1.3.6.1.4.1.1751.2.43.2.20.2.1		not-accessible	A list of Cajun IPX RIP filters.
cjnIpxRipFilterEntry	1.3.6.1.4.1.1751.2.43.2.20.2.1.1		not-accessible	A Cajun IPX RIP filter instance.
FIL cjnIpxRipFilterPrec	1.3.6.1.4.1.1751.2.43.2.20.2.1.1.1	FilterPrec	read-only	The precedence of this RIP filter. The precedence is relative to other RIP filters on the same interface.
ROW cjnIpxRipFilterRowStatus	1.3.6.1.4.1.1751.2.43.2.20.2.1.1.2	RowStatus	read-create	The status of this row, by which new entries may be created, or old entries deleted from this table.
NET cjnIpxRipFilterNetStart	1.3.6.1.4.1.1751.2.43.2.20.2.1.1.3	NetNumber	read-create	The first IPX network number in the range which this filter matches.
NET cjnIpxRipFilterNetEnd	1.3.6.1.4.1.1751.2.43.2.20.2.1.1.4	NetNumber	read-create	The last IPX network number in the range which this filter matches.
INT cjnIpxRipFilterDirection	1.3.6.1.4.1.1751.2.43.2.20.2.1.1.5	INTEGER	read-create	The direction of IPX RIP packets to which this filter applies. Inbound applies the filter only to RIP packets received on the interface. Outbound applies the filter only to RIP packets sent on the interface. Both applies the filter to RIP packets sent and received on the interface.
INT cjnIpxRipFilterAction	1.3.6.1.4.1.1751.2.43.2.20.2.1.1.6	INTEGER	read-create	The action to take if this filter matches an IPX RIP entry. Filter causes the RIP entry to be ignored in received RIP packets or suppressed in sent RIP packets. Allow causes the RIP entry to be accepted in received RIP packets or advertised in sent RIP packets.
I32 cjnIpxRipFilterTicks	1.3.6.1.4.1.1751.2.43.2.20.2.1.1.7	Integer32	read-create	Used to override the delay, in ticks, to reach the IPX network specified in the RIP entry.
I32 cjnIpxRipFilterHops	1.3.6.1.4.1.1751.2.43.2.20.2.1.1.8	Integer32	read-create	Used to override the hops to reach the IPX network specified in the RIP entry.
cjnIpxRipIfGroup	1.3.6.1.4.1.1751.2.43.2.20.3
cjnIpxRipIfTable	1.3.6.1.4.1.1751.2.43.2.20.3.1		not-accessible	A list of Cajun IPX RIP interface entries.
cjnIpxRipIfEntry	1.3.6.1.4.1.1751.2.43.2.20.3.1.1		not-accessible	A Cajun IPX RIP interface instance.
ROW cjnIpxRipIfRowStatus	1.3.6.1.4.1.1751.2.43.2.20.3.1.1.1	RowStatus	read-create	The status of this row, by which new entries may be created, or old entries deleted from this table.
INT cjnIpxRipIfInterpacketGap	1.3.6.1.4.1.1751.2.43.2.20.3.1.1.2	INTEGER	read-create	If set to enable(1), IPX RIP packets from periodic advertisements are sent with an interpacket gap of 55 milliseconds. If set to disable(2), no interpacket gap is used.
INT cjnIpxRipIfUseMaximumPacketSize	1.3.6.1.4.1.1751.2.43.2.20.3.1.1.3	INTEGER	read-create	If set to enable(1), IPX RIP packets will contain as many entries as will fit in the maximum packet size allowable on the interface given the configured encapsulation type. If set to disable(2), IPX RIP packets will contain at most 50 entries.
I32 cjnIpxRipIfUpdateInterval	1.3.6.1.4.1.1751.2.43.2.20.3.1.1.4	Integer32	read-create	The RIP periodic update interval, in seconds.
I32 cjnIpxRipIfAgeMultiplier	1.3.6.1.4.1.1751.2.43.2.20.3.1.1.5	Integer32	read-create	The holding multiplier for information received in RIP updates. RIP information will be kept for the number of seconds indicated by the cjnIpxRipIfUpdateInterval multiplied by the cjnIpxRipIfAgeMultiplier.
INT cjnIpxRipIfTriggeredUpdates	1.3.6.1.4.1.1751.2.43.2.20.3.1.1.6	INTEGER	read-create	Specified whether or not RIP updates are immediately sent on the interface in response to changes in the routing table.
INT cjnIpxRipIfAdvertiseDefaultRouteOnly	1.3.6.1.4.1.1751.2.43.2.20.3.1.1.7	INTEGER	read-create	Specifies whether or not ONLY the default route (FFFFFFFE) is advertised in RIP updates sent on the interface.
INT cjnIpxRipIfMode	1.3.6.1.4.1.1751.2.43.2.20.3.1.1.8	INTEGER	read-create	The handling of RIP packets on the interface. If set to talk(1), RIP packets may be sent on the interface but not received. If set to listen(2), RIP packets may be received but not sent. If set to both(3), RIP packets may be sent and received.
cjnIpxRipIfStatGroup	1.3.6.1.4.1.1751.2.43.2.20.4
cjnIpxRipIfStatTable	1.3.6.1.4.1.1751.2.43.2.20.4.1		not-accessible	A list of Cajun IPX RIP interface statistics entries.
cjnIpxRipIfStatEntry	1.3.6.1.4.1.1751.2.43.2.20.4.1.1		not-accessible	A Cajun IPX RIP interface statistics instance.
C32 cjnIpxRipIfStatTriggeredUpdatesSentEx	1.3.6.1.4.1.1751.2.43.2.20.4.1.1.1	Counter32	read-only	The number of RIP triggered updates sent on the interface.
C32 cjnIpxRipIfStatPeriodicUpdatesSent	1.3.6.1.4.1.1751.2.43.2.20.4.1.1.2	Counter32	read-only	The number of periodic RIP updates sent on the interface.
C32 cjnIpxRipIfStatUpdatesReceived	1.3.6.1.4.1.1751.2.43.2.20.4.1.1.3	Counter32	read-only	The number of RIP updates received on the interface.
C32 cjnIpxRipIfStatRequestsReceived	1.3.6.1.4.1.1751.2.43.2.20.4.1.1.4	Counter32	read-only	The number of RIP requests received on the interface.
C32 cjnIpxRipIfStatBadPacketsReceived	1.3.6.1.4.1.1751.2.43.2.20.4.1.1.5	Counter32	read-only	The number of incorrectly formatted RIP packets received on the interface.
INT cjnIpxRipIfStatsReset	1.3.6.1.4.1.1751.2.43.2.20.4.1.1.6	INTEGER	read-write	When set to the value enable (1) all IPX RIP statistics for this interface are reset to zero after which the value of this MIB object returns to disable(2).

RFC description

IPX RIP protocol configuration and filtering for Lucent Cajun devices.

Start monitoring Lucent/Avaya Cajun switch/router (legacy IPX RIP) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download IPX-RIP-PRIVATE-MIB

What Is IPX-RIP-PRIVATE-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

How to Use in IPNetwork Monitor

RFC description