IPV6-STATIC-ROUTE-MIB

All MIBs › IPV6-STATIC-ROUTE-MIB

Organization: D-Link Corp.

Last Updated: 2007-06-15

Category: Routing Protocols, Technology: IPv6, Vendor: D-Link

Description: D-Link IPv6 static routing MIB providing SNMP objects for configuring and monitoring IPv6 static route entries.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is IPV6-STATIC-ROUTE-MIB?

IPV6-STATIC-ROUTE-MIB is a D-Link proprietary enterprise MIB for configuring and monitoring IPv6 static routes and the associated IPv6 ARP (neighbor) table on D-Link network devices. It exposes route-table style objects describing destination prefixes, next-hop addresses, and route status, alongside neighbor/ARP entries mapping IPv6 addresses to link-layer addresses. In a monitoring context it is used to verify that configured static routes remain active and correctly point to reachable next hops, and that IPv6 neighbor resolution is working, both of which are critical to IPv6 forwarding correctness on the device. It is a proprietary enterprise MIB and does not appear to formally import a standard IETF IPv6 routing MIB. It is typically deployed on D-Link switches and routers used in small-to-midsize enterprise IPv6 network deployments. Engineers can download the IPV6-STATIC-ROUTE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in IPV6-STATIC-ROUTE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link switch or router

Monitoring Examples

No object or table names were supplied for this module (sample_objects is empty), so a concrete polling scenario naming real objects cannot be honestly constructed. In general such a MIB would expose a static-route table (destination/next-hop/status) and an IPv6 ARP/neighbor table, but no specific object names can be confirmed from the available data.

Imported Objects

From DLINK-ID-REC-MIB

dlink-common-mgmt

From RFC1213-MIB

DisplayString

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-SMI

IpAddress
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

MacAddress
RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
swIPv6StaticRouteMIB	1.3.6.1.4.1.171.12.26			The structure of the IPv6 static Route and ARP table management for the proprietary enterprise.
swIPv6StaticRouteCtrl	1.3.6.1.4.1.171.12.26.1
swIPv6StaticRouteInfo	1.3.6.1.4.1.171.12.26.2
swIPv6StaticRouteMgmt	1.3.6.1.4.1.171.12.26.3
swIPv6StaticRouteTable	1.3.6.1.4.1.171.12.26.3.1		not-accessible	This entity's IPv6 static Routing table.
swIPv6StaticRouteEntry	1.3.6.1.4.1.171.12.26.3.1.1		not-accessible	A particular route to a particular destination, under a particular policy. Once an entry is built, it cannot be modified. That is, it just supports create and delete actions.
ADR swIPv6StaticRouteDest	1.3.6.1.4.1.171.12.26.3.1.1.1	Ipv6Address	read-only	Specify the destination network IPv6 address for the route. If swIPv6StaticRouteDest and swIPv6StaticRoutePrefixLen are both 0, it means the default route.
INT swIPv6StaticRoutePrefixLen	1.3.6.1.4.1.171.12.26.3.1.1.2	INTEGER	read-only	The prefix length for this IPv6 address. If swIPv6StaticRouteDest and swIPv6StaticRoutePrefixLen are both 0, it means the default route.
STR swIPv6StaticRouteInterfaceName	1.3.6.1.4.1.171.12.26.3.1.1.3	DisplayString	read-only	This object indicates the name of the interface.
ADR swIPv6StaticRouteNextHop	1.3.6.1.4.1.171.12.26.3.1.1.4	Ipv6Address	read-only	Specify the next hop address for this route.
INT swIPv6StaticRouteMetric	1.3.6.1.4.1.171.12.26.3.1.1.5	INTEGER	read-create	The routing metric for this route.
INT swIPv6StaticRouteWeight	1.3.6.1.4.1.171.12.26.3.1.1.6	INTEGER	read-create	Specified weight value. Used for weighted multipath. The default setting is 1.
STR swIPv6StaticProtocol	1.3.6.1.4.1.171.12.26.3.1.1.7	DisplayString	read-only	The protocol state for this route.
ROW swIPv6StaticRouteStatus	1.3.6.1.4.1.171.12.26.3.1.1.8	RowStatus	read-create	This object indicates the status of this entry.
INT swIPv6StaticRouteBkupState	1.3.6.1.4.1.171.12.26.3.1.1.9	INTEGER	read-create	primary: Specifies the route as the primary route to the destination. backup: Specifies the route as the backup route to the destination. none: The route is not specified. If the route is not specified as the primary route or the backup route, then it will be auto-assigned by the system. The first created is the primary, the second created is the backup.
swIPv6NeighborCacheMgmt	1.3.6.1.4.1.171.12.26.4
swIPv6NeighborCacheTable	1.3.6.1.4.1.171.12.26.4.1		not-accessible	This entity's IPv6 NeighborCache table.
swIPv6NeighborCacheEntry	1.3.6.1.4.1.171.12.26.4.1.1		not-accessible	A particular route to a particular destination, under a particular policy. Once an entry is built, it cannot be modified. That is, it just supports create and delete actions.
ADR swIPv6NeighborCacheIPv6Address	1.3.6.1.4.1.171.12.26.4.1.1.1	Ipv6Address	read-only	The destination IPv6 address of this neighbor.
MAC swIPv6NeighborCacheMacAddress	1.3.6.1.4.1.171.12.26.4.1.1.2	MacAddress	read-only	The MAC address of this neighbor .
STR swIPv6NeighborCacheInterfaceName	1.3.6.1.4.1.171.12.26.4.1.1.3	DisplayString	read-only	This object indicates the name of the IP interface.
INT swIPv6NeighborCacheReachState	1.3.6.1.4.1.171.12.26.4.1.1.4	INTEGER	read-only	This object indicates the reachability state of this neighbor.
ROW swIPv6NeighborCacheRouteStatus	1.3.6.1.4.1.171.12.26.4.1.1.5	RowStatus	read-create	This object indicates the status of this entry.
INT swIPv6NeighborCacheDeleteAction	1.3.6.1.4.1.171.12.26.4.2	INTEGER	read-write	This object will delete the cached neighbor entries. all: Deletes all cached neighbor entries include static and dynamic entries. static: Deletes all the cached static neighbor entries. dynamic: Deletes all the cached dynamic neighbor entries.

RFC description

D-Link proprietary MIB for IPv6 static routing and ARP table management.

Start monitoring D-Link switch or router (IPv6 static routes/ARP) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download IPV6-STATIC-ROUTE-MIB

What Is IPV6-STATIC-ROUTE-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description