HUAWEI-SNMP-NOTIFICATION-MIB

All MIBs › HUAWEI-SNMP-NOTIFICATION-MIB

Organization: Huawei Technologies Co.,Ltd

Last Updated: 2012-11-02

Category: Alarm and Event Management, Domain: Network Management, SNMP Framework, Vendor: Huawei

Description: Huawei SNMP notification MIB for configuring trap filters, notification targets, and event severity thresholds.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-SNMP-NOTIFICATION-MIB?

HUAWEI-SNMP-NOTIFICATION-MIB is a Huawei private-enterprise MIB that configures how a Huawei device sends SNMP host notifications, covering trap filters, notification targets, syslog integration, and event severity thresholds. It exposes configuration data for alarm and event notification delivery — which hosts receive traps, which log/syslog destinations are used, and severity-based filtering — rather than raw hardware sensor readings itself. Its relevance to hardware/software status monitoring is that it is the delivery mechanism through which all other fault/alarm conditions (hardware faults, software errors, threshold breaches) on the device get reported to management stations, so verifying its configuration ensures real hardware/software problems are actually surfaced to operators. It is designed around and depends on the standard SNMP notification framework and Huawei's own alarm/event MIB tree for the underlying condition definitions it filters and forwards. It is typically deployed across Huawei networking equipment (routers, switches) in enterprise and carrier networks, where HUAWEI-SNMP-NOTIFICATION-MIB SNMP monitoring centralizes and tunes alarm/event/trap delivery to NMS platforms.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-SNMP-NOTIFICATION-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei router/switch

Monitoring Examples

No object names were provided in the source excerpt, so a concrete polling walk cannot be grounded in named identifiers; based on the module description, an administrator would configure/verify trap-target host entries, severity threshold filters, and syslog forwarding settings to ensure critical alarms (e.g., hardware faults) are actually delivered to the NMS. A misconfigured severity filter silently dropping high-severity events would mean real device faults go unreported even though the underlying condition MIBs detect them correctly.

What Can Be Monitored

trap/notification target configuration
event severity filtering thresholds
syslog forwarding configuration

Imported Objects

From HUAWEI-DEVICE-MIB

hwFrameIndex	OBJECT-TYPE
hwNewDeviceIpAddr
hwOldDeviceIpAddr
hwPortIndex	OBJECT-TYPE
hwSlotIndex	OBJECT-TYPE
hwSysIpAddr	OBJECT-TYPE
hwSysVersion	OBJECT-TYPE

From HUAWEI-MIB

huaweiUtility

OBJECT-IDENTITY

From HUAWEI-TC-MIB

hwAlarmSn	OBJECT-TYPE
hwTrapType	OBJECT-TYPE

From IF-MIB

ifIndex

OBJECT-TYPE

From SNMP-TARGET-MIB

snmpTargetAddrName	OBJECT-TYPE
snmpTargetAddrTAddress	OBJECT-TYPE

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
RowStatus
TEXTUAL-CONVENTION
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
hwAlarm	1.3.6.1.4.1.2011.6.30.4
INT hwAlarmAdminStatus	1.3.6.1.4.1.2011.6.30.7.1.1.9	INTEGER	read-write	Alarm management status. Options: 1. init(1) -The default status is init(1). 2. conversion(2) -If an alarm needs to be converted into an event, perform the setting operation to set the management status of the alarm to conversion(2).
U32 hwAlarmBufferMaxSn	1.3.6.1.4.1.2011.6.30.1.2	Unsigned32	read-only	Maximum serial number of the alarm buffered in the current system.
U32 hwAlarmBufferMinSn	1.3.6.1.4.1.2011.6.30.1.1	Unsigned32	read-only	Minimum serial number of the alarm buffered in the current system.
INT hwAlarmClass	1.3.6.1.4.1.2011.6.30.7.1.1.3	INTEGER	read-only	Alarm class. Currently, the system supports two alarm classes. Options: 1. faultalarm(1) -indicates the fault alarm. 2. restorealarm(2) -indicates the restore alarm.
I32 hwAlarmClearedNum	1.3.6.1.4.1.2011.6.30.17.15	Integer32	accessible-for-notify	Cleared active alarm number.
NTF hwAlarmClearedReportTrap	1.3.6.1.4.1.2011.6.30.18.1.0.5			The agent generates this trap when clear active alarm completed.
OCT hwAlarmClearedSnList	1.3.6.1.4.1.2011.6.30.17.16	OCTET STRING	accessible-for-notify	The serial number list of cleared alarm (the serial number are separated with comma).
hwAlarmCtrl	1.3.6.1.4.1.2011.6.30.7
hwAlarmCtrlEntry	1.3.6.1.4.1.2011.6.30.7.1.1		not-accessible	Alarm control table. It is used to set the alarm level through the NMS or query the alarm list supported in the system. The information that can be queried includes the alarm ID, alarm name, alarm class, alarm type, alarm level, alarm default level, count of the alarm in the statistical period, count of the alarm in the previous statistical period and alarm management status. The index of this entry is hwAlarmID.
hwAlarmCtrlTable	1.3.6.1.4.1.2011.6.30.7.1		not-accessible	Alarm control table. It is used to set the alarm level through the NMS or query the alarm list supported in the system. The information that can be queried includes the alarm ID, alarm name, alarm class, alarm type, alarm level, alarm default level, count of the alarm in the statistical period, count of the alarm in the previous statistical period and alarm management status. The index of this table is hwAlarmID.
SEV hwAlarmDefaultLevel	1.3.6.1.4.1.2011.6.30.7.1.1.5	SeverityLevel	read-only	Alarm default level. The alarm level in the system can be changed and thus the alarm default level and alarm level need to be distinguished. Options: 1. critical(1) -indicates the critical alarm. 2. major(2) -indicates the major alarm. 3. minor(3) -indicates the minor alarm. 4. warning(4) -indicates the warning alarm.
hwAlarmExpCtrlEntry	1.3.6.1.4.1.2011.6.30.12.1.1		not-accessible	Alarm output control table. It is used to query and configure whether the alarm signal is output through the external alarm interface. The index of this entry is hwAlarmExpID.
hwAlarmExpCtrlTable	1.3.6.1.4.1.2011.6.30.12.1		not-accessible	Alarm output control table. It is used to query and configure whether the alarm signal is output through the external alarm interface. The index of this table is hwAlarmExpID.
I32 hwAlarmExpID	1.3.6.1.4.1.2011.6.30.12.1.1.1	Integer32	not-accessible	Index of hwAlarmExpCtrlTable. It is used to configure whether a specified alarm is output. In the configuration, the fault alarms refer to all the fault alarms with level higher than warning in the system.
INT hwAlarmExpSign	1.3.6.1.4.1.2011.6.30.12.1.1.2	INTEGER	read-write	Flag that indicates whether the alarm is output through the external alarm interface. The values are as follows: Options: 1. disable(1) -indicates that the alarm is not output through the external alarm interface. 2. enable(2) -indicates that the alarm is output through the external alarm interface.
hwAlarmExpSignal	1.3.6.1.4.1.2011.6.30.12
I32 hwAlarmID	1.3.6.1.4.1.2011.6.30.7.1.1.1	Integer32	not-accessible	Index object of the alarm control table. The index value is the alarm ID and the information about the alarm control table is obtained according to the current alarm ID.
I32 hwAlarmIndex	1.3.6.1.4.1.2011.6.30.1.7.1.1	Integer32	not-accessible	Index of the alarm reporting control table. The index value is the alarm ID.
hwAlarmJitterProof	1.3.6.1.4.1.2011.6.30.9.10
I32 hwAlarmJitterProofInterval	1.3.6.1.4.1.2011.6.30.9.10.2	Integer32	read-write	Alarm jitter-proof interval. Interval of the alarm jitter-proof. Range: 1-60 Default: 10 Unit: second DEFVAL { 10 }
INT hwAlarmJitterProofSwitch	1.3.6.1.4.1.2011.6.30.9.10.1	INTEGER	read-write	Alarm jitter-proof function. Through this function, the alarm trap is reported to the NMS after a period that can be set. The default period is 10s and the range is 1-60s. If the alarm is rectified within the preset period, the alarm trap is not reported to the NMS. The value range of the function is 1-2. Options: 1. on(1) -indicates that the function is enabled. 2. off(2) -indicates that the function is disabled. DEFVAL { off }.
SEV hwAlarmLevel	1.3.6.1.4.1.2011.6.30.7.1.1.4	SeverityLevel	read-write	Alarm level. Currently, the system supports four alarm levels. Options: 1. critical(1) -indicates the critical alarm. 2. major(2) -indicates the major alarm. 3. minor(3) -indicates the minor alarm. 4. warning(4) -indicates the warning alarm.
OCT hwAlarmName	1.3.6.1.4.1.2011.6.30.7.1.1.2	OCTET STRING	read-only	Alarm name. It is used to briefly describe the alarm triggered by the system.
INT hwAlarmRecordAdminStatus	1.3.6.1.4.1.2011.6.30.8.1.1.2	INTEGER	read-write	Recorded management status of the alarm. Options: 1. clear(1) -indicates that the fault alarm is cleared. 2. exist(2) -indicates that the fault alarm exists.
hwAlarmRecordClear	1.3.6.1.4.1.2011.6.30.8
hwAlarmRecordClearEntry	1.3.6.1.4.1.2011.6.30.8.1.1		not-accessible	Alarm clear table. It is used to clear the active alarm by specified serial number through the NMS. The alarm refers to the alarm whose recovery alarm is not generated. The index of this entry is hwAlarmRecordSn. hwAlarmRecordSn is the serial number of the alarm to be cleared.
OCT hwAlarmRecordClearOperate	1.3.6.1.4.1.2011.6.30.8.2	OCTET STRING	read-create	Serial number list of the active alarm to be cleared.
hwAlarmRecordClearTable	1.3.6.1.4.1.2011.6.30.8.1		not-accessible	Alarm clear table. It is used to clear the active alarm by specified serial number through the NMS. The alarm refers to the alarm whose recovery alarm is not generated. The index of this table is hwAlarmRecordSn. hwAlarmRecordSn is the serial number of the alarm to be cleared.
I32 hwAlarmRecordSn	1.3.6.1.4.1.2011.6.30.8.1.1.1	Integer32	not-accessible	Index of the alarm or event that is not recovered and to be cleared. The index value is the serial number of the alarm or event. The serial number is saved on the NMS and can be issued through the NMS.
hwAlarmSendEntry	1.3.6.1.4.1.2011.6.30.1.7.1		not-accessible	Alarm reporting control table. It is used to control by alarm ID whether to report the trap generated corresponding to an alarm to the trap host. The index of this entry is object hwAlarmIndex.
INT hwAlarmSendSwitch	1.3.6.1.4.1.2011.6.30.1.7.1.2	INTEGER	read-write	Control function of whether to report the trap generated corresponding to an alarm to the trap host. Options: 1. on(1) -indicates that the trap generated corresponding to the alarm of object hwAlarmIndex needs to be reported to the trap host. 2. off(2) -indicates that the trap generated corresponding to the alarm of object hwAlarmIndex need not to be reported to the trap host.
hwAlarmSendTable	1.3.6.1.4.1.2011.6.30.1.7		not-accessible	Alarm reporting control table. It is used to control by alarm ID whether to report the trap generated corresponding to an alarm to the trap host. The index of this table is object hwAlarmIndex.
INT hwAlarmServiceEffect	1.3.6.1.4.1.2011.6.30.7.1.1.10	INTEGER	read-write	Alarm Service effect status. It is used to describe the Service effect of the alarm and is classified into two types. Options: 1. nonserviceaffect(1) -indicates the alarm is a non-service affecting condition. 2. serviceaffect(2) -indicates the alarm is a service affecting condition.
DAT hwAlarmStatCurPeriodStartTime	1.3.6.1.4.1.2011.6.30.4.4	DateAndTime	read-only	The alarm statistics function is to automatically collect the alarm statistics according to the preset period and this object is used to query the start time of the current statistical period.
C32 hwAlarmStatCurrentNum	1.3.6.1.4.1.2011.6.30.4.6.1.2	Counter32	read-only	Query the count of the alarm occurring in the current statistical period by index.
C32 hwAlarmStatCurrNum	1.3.6.1.4.1.2011.6.30.7.1.1.7	Counter32	read-only	Count of the alarm occurring in the current period.
I32 hwAlarmStatID	1.3.6.1.4.1.2011.6.30.4.6.1.1	Integer32	read-only	Index of operation table hwAlarmStatInfoTable. It is used to indicate the ID of the alarm to be queried.
hwAlarmStatInfoEntry	1.3.6.1.4.1.2011.6.30.4.6.1		not-accessible	Function of querying the alarm statistical information. It is used to query the count of the alarm occurring in the statistical period. The index of this entry is hwAlarmStatID. It is used to specify the alarm whose count is queried. The index value is the alarm ID.
hwAlarmStatInfoTable	1.3.6.1.4.1.2011.6.30.4.6		not-accessible	Function of querying the alarm statistical information. It is used to query the count of the alarm occurring in the statistical period. The index of this table is hwAlarmStatID. It is used to specify the alarm whose count is queried. The index value is the alarm ID.
C32 hwAlarmStatLastNum	1.3.6.1.4.1.2011.6.30.4.6.1.3	Counter32	read-only	Query the count of the alarm occurring in the previous statistical period by index.
I32 hwAlarmStatPeriod	1.3.6.1.4.1.2011.6.30.4.2	Integer32	read-write	Alarm statistics period. Range: 1-8760 Default: 24 Unit: hour
C32 hwAlarmStatPrevNum	1.3.6.1.4.1.2011.6.30.7.1.1.8	Counter32	read-only	Count of the alarm occurring in the previous period.
INT hwAlarmStatSave	1.3.6.1.4.1.2011.6.30.4.3	INTEGER	read-write	Operation of saving the alarm statistical information. The statistical information is saved to the flash memory according to the preset period. Options: 1. save(2) -indicates that the information is saved. 2. nosaving(3) -indicates that the information is not saved.
INT hwAlarmSynAdminStatus	1.3.6.1.4.1.2011.6.30.1.5	INTEGER	read-write	When the alarm whose synchronization is initiated by the NMS, one of the following methods can be used: Options: 1. other(1) -other. 2. stop(2) -stop. 3. interval(3) -indicates that synchronize the alarm by serial number (that is, synchronize all the alarms in the system). During the synchronization, hwAlarmSynBeginSn, hwAlarmSynEndSn and hwSynTrapAdminStatus need to be issued. The corresponding value is interval(3). 4. all(4) -indicates that synchronize all the active alarms (the active alarms refer to the alarm whose fault alarms are already sent but the corresponding recovery alarms are not sent). hwSynTrapAdminStatus is issued directly and the corresponding value is all (4).
U32 hwAlarmSynBeginSn	1.3.6.1.4.1.2011.6.30.1.3	Unsigned32	read-write	Starting serial number of the alarm trap whose synchronization is initiated by the NMS. The value ranges from hwAlarmBufferMinSn to hwAlarmBufferMaxSn. When the value that is not in the range is used, an error is returned.
U32 hwAlarmSynEndSn	1.3.6.1.4.1.2011.6.30.1.4	Unsigned32	read-write	Ending serial number of the alarm trap whose synchronization is initiated by the NMS. The value ranges from hwAlarmBufferMinSn to hwAlarmBufferMaxSn. When the value that is not in the range is used, an error is returned. The value cannot be smaller than the value of hwAlarmSynBeginSn.
hwAlarmSynObjects	1.3.6.1.4.1.2011.6.30.1
EVE hwAlarmType	1.3.6.1.4.1.2011.6.30.7.1.1.6	EventType	read-only	Alarm type. It is used to describe the major cause of the alarm and is classified into five types. Options: 1. communication(1) -indicates the communication alarm. 2. service(2) -indicates the service quality alarm. 3. process(3) -indicates the process error alarm. 4. equipment(4) -indicates the hardware device alarm. 5. environment(5) -indicates the environment alarm.
NTF hwAlmSynBeginTrap	1.3.6.1.4.1.2011.6.30.18.1.0.3			The agent generates this trap when alarm synchronization starts.
NTF hwAlmSynEndTrap	1.3.6.1.4.1.2011.6.30.18.1.0.4			The agent generates this trap when alarm synchronization completes.
INT hwClrAlarmExpSignal	1.3.6.1.4.1.2011.6.30.12.2	INTEGER	read-write	It is used to clear the alarm output signal. After the alarm output signal is cleared, the recovery notification is sent to the external alarm interface and the corresponding active alarm is cleared. For the current external alarm interface, only the one-LED and three-LED output mode is supported. In the one-LED output mode, the alarm output signal cannot be cleared by level and can be cleared only by all(1); In the three-LED output mode, the alarm output signal can be cleared by all the following parameters. Options: 1. other(-1) -indicates the default status in the system. 2. all(1) -indicates that all the alarm output signals are cleared. 3. critical(2) -indicates that the critical alarm output signal is cleared. 4. major(3) -indicates that the major alarm output signal is cleared. 5. minor(4) -indicates that the minor alarm output signal is cleared.
OCT hwCommunityReadName	1.3.6.1.4.1.2011.6.30.17.10	OCTET STRING	accessible-for-notify	Community read name, a kind of string parameter.
OCT hwCommunityWriteName	1.3.6.1.4.1.2011.6.30.17.11	OCTET STRING	accessible-for-notify	Community write name, a kind of string parameter.
INT hwEventAdminStatus	1.3.6.1.4.1.2011.6.30.6.1.1.9	INTEGER	read-write	Event management status. Currently, the system supports two states. Options: 1. init(1) -During the setting operation, you can change only the event that is in the initial state to the alarm but cannot change an alarm to an event. Therefore, init(1) can be implemented only through the getting operation to check whether the current state is initial. 2. conversion(2) -If an event needs to be converted into an alarm, perform the setting operation through conversion(2).
INT hwEventClass	1.3.6.1.4.1.2011.6.30.6.1.1.3	INTEGER	read-only	Event class. Currently, the system supports two event classes: Options: 1. running(1) -indicates the running event, such as the prompt displayed during the loading process. 2. security(2) -indicates the event that affects the system security status of the access devices, for example, the event wherein a user try to access the system to add, delete, or change the user account in the system, thus changing the system security status.
INT hwEventConditionEffect	1.3.6.1.4.1.2011.6.30.6.1.1.10	INTEGER	read-only	Event Effect. It is used to describe the Service effect of the event and is classified into two types. Options: 1. standingcondition(1) -indicates a condition is standing. 2. transientcondition(2) -indicates a condition is transient.
hwEventCtrl	1.3.6.1.4.1.2011.6.30.6
hwEventCtrlEntry	1.3.6.1.4.1.2011.6.30.6.1.1		not-accessible	Event control table. It is used to set the event level through the NMS or query the event list supported in the system. The information that can be queried includes the event ID, event name, event class, event type, event level, event default level, count of the event in the statistical period, count of the event in the previous statistical period and event management status. The index of this entry is the hwEventID.The index value is the event ID.
hwEventCtrlTable	1.3.6.1.4.1.2011.6.30.6.1		not-accessible	Event control table. It is used to set the event level through the NMS or query the event list supported in the system. The information that can be queried includes the event ID, event name, event class, event type, event level, event default level, count of the event in the statistical period, count of the event in the previous statistical period and event management status. The index of this table is the hwEventID.The index value is the event ID.
SEV hwEventDefaultLevel	1.3.6.1.4.1.2011.6.30.6.1.1.5	SeverityLevel	read-only	Event default level. When being defined, each event has a default level. In the system, however, the level can be configured according to the actual requirements. This object returns the default level. Options: 1. critical(1) -indicates the critical event. 2. major(2) -indicates the major event. 3. minor(3) -indicates the minor event. 4. warning(4) -indicates the warning event. 5. cleared(5) -indicates the claered event. 7. notalarmed(7) -indicates the not-alarmed event. 8. notreported(8) -indicates the not-reported event.
I32 hwEventID	1.3.6.1.4.1.2011.6.30.6.1.1.1	Integer32	not-accessible	Index object of the event control table. The index value is the event ID and the information about the event control table is obtained according to the current event ID.
SEV hwEventLevel	1.3.6.1.4.1.2011.6.30.6.1.1.4	SeverityLevel	read-write	Event type. Options: 1. critical(1) -indicates the critical event. The security event must be recorded in the log. 2. major(2) -indicates the major event. The security event must be recorded in the log. 3. minor(3) -indicates the minor event. The security event must be recorded in the log. 4. warning(4) -indicates the warning event. 5. cleared(5) -indicates the cleared event. 7. notalarmed(7) -indicates the not-alarmed event. 8. notreported(8) -indicates the not-reported event.
OCT hwEventName	1.3.6.1.4.1.2011.6.30.6.1.1.2	OCTET STRING	read-only	Event name. It is used to briefly describe the event trigged by the system.
C32 hwEventStatCurrNum	1.3.6.1.4.1.2011.6.30.6.1.1.7	Counter32	read-only	Count of the event occurring in the current period.
C32 hwEventStatPrevNum	1.3.6.1.4.1.2011.6.30.6.1.1.8	Counter32	read-only	Count of the event occurring in the previous period.
EVE hwEventType	1.3.6.1.4.1.2011.6.30.6.1.1.6	EventType	read-only	Event type. Currently, the system supports five event types. Options: 1. communication(1) -indicates the communication event. 2. service(2) -indicates the service quality event. 3. process(3) -indicates the process error event. 4. equipment(4) -indicates the hardware device event. 5. environment(5) -indicates the environment event.
OCT hwHostName	1.3.6.1.4.1.2011.6.30.17.7	OCTET STRING	accessible-for-notify	Host Name,a kind of string parameter.
NTF hwIllegalMessageTrap	1.3.6.1.4.1.2011.6.30.18.2.0.2			After the firewall is enabled, this trap message is reported when the system receives an SNMP packet whose IP address is refused by the firewall. A maximum of 15 such trap messages are sent in 15 minutes.
hwLogHost	1.3.6.1.4.1.2011.6.30.14
INT hwLogHostConfigStatus	1.3.6.1.4.1.2011.6.30.14.1.1.2	INTEGER	read-only	Obtained status of the log host. Options: 1. configed(1) -indicates that the log host is configured. 2. unconfiged(2) -indicates that the log host is not configured.
hwLogHostEntry	1.3.6.1.4.1.2011.6.30.14.1.1		not-accessible	Querying the status of the log host configured in the current system. The index of this entry is hwLogHostIP.
IP hwLogHostIP	1.3.6.1.4.1.2011.6.30.14.1.1.1	IpAddress	not-accessible	IP address of the log host. It is used to obtain the host status by IP address of the log host.
OCT hwLogHostMacAddress	1.3.6.1.4.1.2011.6.30.17.8	OCTET STRING	accessible-for-notify	Mac Address,a kind of string parameter.
hwLogHostTable	1.3.6.1.4.1.2011.6.30.14.1		not-accessible	Querying the status of the log host configured in the current system. The index of this table is hwLogHostIP.
I32 hwLogMaxSn	1.3.6.1.4.1.2011.6.30.13.1.1.3	Integer32	read-only	Maximum serial number of the log that can be synchronized currently.
I32 hwLogMinSn	1.3.6.1.4.1.2011.6.30.13.1.1.2	Integer32	read-only	Minimum serial number of the log that can be synchronized currently.
hwLogSyn	1.3.6.1.4.1.2011.6.30.13
INT hwLogSynAdminStatus	1.3.6.1.4.1.2011.6.30.13.1.1.6	INTEGER	read-write	The synchronizing administration. Options: 1.nosynmode(-1)-indicates the default status in the system. 2.interval(3) -indicates that the host should send all the log between hwLogSynBeginSn and hwLogSynEndSn. 3.all(4) -indicates that the host sends all log to NMS.
I32 hwLogSynBeginSn	1.3.6.1.4.1.2011.6.30.13.1.1.4	Integer32	read-write	Starting index of the log that is synchronized. The value ranges from hwLogMinSn to hwLogMaxSn. The hwLogSynBeginSn value of -1 indicates there is no log synchronizing.
I32 hwLogSynEndSn	1.3.6.1.4.1.2011.6.30.13.1.1.5	Integer32	read-write	Ending index of the log that is synchronized. The value ranges from hwLogMinSn to hwLogMaxSn and must be larger than hwLogSynBeginSn. The hwLogSynEndSn value of -1 indicates there is no log synchronizing.
hwLogSynEntry	1.3.6.1.4.1.2011.6.30.13.1.1		not-accessible	Log synchronization table. It is used to query the minimum and maximum serial numbers of the logs that can be synchronized and set the condition of synchronizing the log. The index of this entry is hwLogSynType. The index value is the synchronization type.
hwLogSynTable	1.3.6.1.4.1.2011.6.30.13.1		not-accessible	Log synchronization table. It is used to query the minimum and maximum serial numbers of the logs that can be synchronized and set the condition of synchronizing the log. The index of this table is hwLogSynType. The index value is the synchronization type.
INT hwLogSynType	1.3.6.1.4.1.2011.6.30.13.1.1.1	INTEGER	not-accessible	Type of the log that is synchronized. Currently, the logs are classified into two types. Options: 1. operating(1) -indicates the operating log. 2. security(2) -indicates the security log.
I32 hwMaintainIndex	1.3.6.1.4.1.2011.6.30.1.8.1.1	Integer32	not-accessible	Currently, the object is not supported.
hwMaintainSendEntry	1.3.6.1.4.1.2011.6.30.1.8.1		not-accessible	Currently, the table is not supported. The index of this entry is hwMaintainIndex.
INT hwMaintainSendSwitch	1.3.6.1.4.1.2011.6.30.1.8.1.2	INTEGER	read-write	Currently, the object is not supported. Options: 1.on(1) -on. 2.off(2)-off.
hwMaintainSendTable	1.3.6.1.4.1.2011.6.30.1.8		not-accessible	Currently, the table is not supported. The index of this table is hwMaintainIndex.
NTF hwMessageReportTrap	1.3.6.1.4.1.2011.6.30.18.1.0.1			The register trap message is reported by the host to the NMS when the function of handshake between the host and the NMS is enabled.
IP hwNMSIPAddr	1.3.6.1.4.1.2011.6.30.17.13	IpAddress	accessible-for-notify	The NMS IP.
hwNotificationCause	1.3.6.1.4.1.2011.6.30.15
OCT hwNotificationCauseDesc	1.3.6.1.4.1.2011.6.30.15.1.1.2	OCTET STRING	read-only	Cause description of the alarm or event.
hwNotificationCauseEntry	1.3.6.1.4.1.2011.6.30.15.1.1		not-accessible	Alarm or event cause querying table. It is used to query the cause description of the alarm or event by alarm or event ID. The index of this entry is hwNotificationCauseID and the index value is the alarm or event ID.
I32 hwNotificationCauseID	1.3.6.1.4.1.2011.6.30.15.1.1.1	Integer32	not-accessible	The index of hwNotificationCauseTable. The value is the alarm or event ID.
hwNotificationCauseTable	1.3.6.1.4.1.2011.6.30.15.1		not-accessible	Alarm or event cause querying table. It is used to query the cause description of the alarm or event by alarm or event ID. The index of this table is hwNotificationCauseID and the index value is the alarm or event ID.
OCT hwNotificationTime	1.3.6.1.4.1.2011.6.30.17.14	OCTET STRING	accessible-for-notify	Current date and time of the system.
INT hwNotificationType	1.3.6.1.4.1.2011.6.30.17.5	INTEGER	accessible-for-notify	It's value is a configuration. Options: 1. event(10) -event, NSA(non-service affecting condition). 2. adacnsa(11) -ADAC(auto detect auto clear) alarm, NSA(non-service affecting condition). 3. admcnsa(12) -ADMC(auto detect manual clear) alarm, NSA(non-service affecting condition). 4. adacsa(27) -ADAC(auto detect auto clear) alarm, SA(service affecting condition). 5. admcsa(28) -ADMC(auto detect manual clear) alarm, SA(service affecting condition).
hwNotifyFilter	1.3.6.1.4.1.2011.6.30.9
I32 hwNotifyFilterCondition	1.3.6.1.4.1.2011.6.30.9.1.1.3	Integer32	not-accessible	Detailed condition of filtering the alarm. The range is determined by different alarm types as follows: When the type of the object to be filtered is system(1), hwNotifyFilterCondition can be any value. When the type of the object to be filtered is level(2), the object to be filtered is the alarm, the range is 1-4. Options: 1. critical(1) -indicates the critical alarm. 2. major(2) -indicates the major alarm. 3. minor(3) -indicates the minor alarm. 4. warning(4) -indicates the warning alarm. In GR version, When the type of the object to be filtered is level(2), the object to be filtered is the event, the range is 7-8. Options: 1. notalarmed(7) -indicates the not-alarmed event. 2. notreported(8) -indicates the not-reported event. When the type of the object to be filtered is type(3), the range is 1-5. Options: 1. communication(1)-indicates the communication alarm. 2. service(2) -indicates the service quality alarm. 3. process(3) -indicates the process error alarm. 4. equipment(4) -indicates the hardware device alarm. 5. environment(5) -indicates the environment alarm. When the type of the object to be filtered is id(4), the range is 1-0xffffffff, that is, the ID of the alarm or event. When the type of the object to be filtered is parameter(5), the range is a 32-bit value of the unsigned long type. The first eight bits of the value indicate the type of the object to be filtered. Currently, the system supports four types of the objects to be filtered. The type is 0xFF000000. 0 indicates that the object is filtered by shelf ID. If the first eight bits are 0, the shelf ID is obtained from mask 0x00FF0000. 1 indicates that the object is filtered by shelf ID and slot ID. If the first eight bits are 1, the shelf ID is obtained from mask 0x00FF0000 and the slot ID is obtained from mask 0x0000FF00. 2 indicates that the object is filtered by shelf ID, slot ID and port ID. If the first eight bits are 2, the shelf ID is obtained from mask 0x00FF0000, the slot ID is obtained from mask 0x0000FF00, and the port ID is obtained from mask 0x000000FF. 3 indicates that the object is filtered by VLAN ID. If the first eight bits are 3, the VLAN ID is obtained from mask 0x00FFFFFF. The value is issued as a hexadecimal numeral.
hwNotifyFilterEntry	1.3.6.1.4.1.2011.6.30.9.1.1		not-accessible	Filter table of the alarm, event and trap. It is used to set the filter condition of the alarm, event and trap through the NMS. The indexes of this entry are hwNotifyFilterObject, hwNotifyFilterType and hwNotifyFilterCondition.
INT hwNotifyFilterObject	1.3.6.1.4.1.2011.6.30.9.1.1.1	INTEGER	not-accessible	Description of all the filter objects supported by hwNotifyFilterTable. Options: 1. event(1) -indicates that the object to be filtered is the event. 2. alarm(2) -indicates that the object to be filtered is the alarm. The following items indicate the trap types that are to be filtered: 3. maintain(3)-indicates the maintenance trap. 4. snmpstd(4) -indicates the standard trap. 5. topo(5) -indicates the topological trap. 6. test(6) -indicates the test trap. 7. datachange(15)-indicates the data change trap.
ROW hwNotifyFilterRowStatus	1.3.6.1.4.1.2011.6.30.9.1.1.4	RowStatus	read-create	The status of this conceptual row. createAndGo(4) is supplied to create a new instance of a conceptual row. destroy(6) is supplied to delete the instances associated with an existing conceptual row.
hwNotifyFilterTable	1.3.6.1.4.1.2011.6.30.9.1		not-accessible	Filter table of the alarm, event and trap. It is used to set the filter condition of the alarm, event and trap through the NMS. The indexes of this table are hwNotifyFilterObject, hwNotifyFilterType and hwNotifyFilterCondition.
INT hwNotifyFilterType	1.3.6.1.4.1.2011.6.30.9.1.1.2	INTEGER	not-accessible	Description of the filter type. Currently, the system supports five filter types. Options: 1. system(1) -indicates that the object is filtered by network element (NE). 2. level(2) -indicates that the object is filtered by level. 3. type(3) -indicates that the object is filtered by type. 4. id(4) -indicates that the object is filtered by ID. 5. parameter(5) -indicates that the object is filtered by parameter. When the filter object is maintain(3), snmpstd(4), topo(5), test(6), or datachange(15), the filter type (an enumerated value) can only be id(4), indicating that the object is filtered by trap ID. Other alarms and events are supported.
INT hwNotifySubAdminStatus	1.3.6.1.4.1.2011.6.30.9.11.1.2	INTEGER	read-write	Status of alarm shielding. Only two states are supported, namely, received and shielded. Options: 1. enable(1) -indicates that the alarm is received. 2. disable(2) -indicates that the alarm is shielded.
OCT hwNotifySubContentList	1.3.6.1.4.1.2011.6.30.9.11.1.3	OCTET STRING	read-write	ID list of the alarm or event to be shielded. It is all or the ID list (the IDs are separated with comma). All indicates all the alarms or events.
hwNotifySubEntry	1.3.6.1.4.1.2011.6.30.9.11.1		not-accessible	Alarm shielding table. It is used to set the condition of shielding the alarm. The index of this entry is hwNotifySubHostAddress, which is the IP address of a trap host whose alarm is shielded.
IP hwNotifySubHostAddress	1.3.6.1.4.1.2011.6.30.9.11.1.1	IpAddress	not-accessible	IP address of the target host for which all the traps generated for the alarms are shielded.
hwNotifySubTable	1.3.6.1.4.1.2011.6.30.9.11		not-accessible	Alarm shielding table. It is used to set the condition of shielding the alarm. The index of this table is hwNotifySubHostAddress, which is the IP address of a trap host whose alarm is shielded.
NTF hwOperationFromNmsTrap	1.3.6.1.4.1.2011.6.30.18.2.0.1			This trap is reported when important operation from NMS.
I32 hwProtocolVersion	1.3.6.1.4.1.2011.6.30.17.9	Integer32	accessible-for-notify	The version of SNMP protocol. 1 :indicates the SNMP v1 protocol. 2 :indicates the SNMP v2c protocol. 3 :indicates the SNMP v3 protocol.
OCT hwRtuConfigID	1.3.6.1.4.1.2011.6.30.3.11.1.1	OCTET STRING	read-write	The ConfigID of RTU. Currently, the object is not supported.
hwRtuConfigIDEntry	1.3.6.1.4.1.2011.6.30.3.11.1		not-accessible	RTU ConfigID table.The index of this entry is ifIndex. Currently, the object is not supported.
hwRtuConfigIDTable	1.3.6.1.4.1.2011.6.30.3.11		not-accessible	RTU ConfigID table.The index of this table is ifIndex. Currently, the object is not supported.
INT hwRtuResetAllConfigID	1.3.6.1.4.1.2011.6.30.3.2	INTEGER	read-write	Set operation used to reset all RTU's configID. Options: 1. unknown(1) -means don't known if RTU is administrable, setting all configID to '-1'. 2. administrable(2)-means RTU is administrable, setting all configID to '0'. Get operation is useless. Currently, the object is not supported.
hwRtuTrapRestrain	1.3.6.1.4.1.2011.6.30.3
INT hwRtuTrapRestrainSwitch	1.3.6.1.4.1.2011.6.30.3.1	INTEGER	read-write	RTU trap restrain switch status. Options: 1. enable(1) -RTU trap restrain switch is enable. 2. disable(2) -RTU trap restrain switch is disable.
NTF hwShakeMessageTrap	1.3.6.1.4.1.2011.6.30.18.1.0.2			Shake between host and NMS. After the function of handshake between the host and the NMS is enabled, the host periodically sends a trap message to the NMS if it registers with the NMS successfully.
hwSnmpNotiAlarmTraps	1.3.6.1.4.1.2011.6.30.18.2
hwSnmpNotiAlarmTrapsPrefix	1.3.6.1.4.1.2011.6.30.18.2.0
hwSnmpNotiCommonTraps	1.3.6.1.4.1.2011.6.30.18.1
hwSnmpNotiCommonTrapsPrefix	1.3.6.1.4.1.2011.6.30.18.1.0
hwSnmpNotiTraps	1.3.6.1.4.1.2011.6.30.18
INT hwSpecificTrapType	1.3.6.1.4.1.2011.6.30.17.4	INTEGER	accessible-for-notify	Specific trap type. Options: 1. alarm(2) -indicates the trap type is alarm trap. 2. maintain(3) -indicates the trap type is maintain trap. 3. standard(4) -indicates the trap type is snmp standard trap. 4. topo(5) -indicates the trap type is topo trap. 5. test(6) -indicates the trap type is test trap. 6. fault(12) -indicates the trap type is fault alarm from alarm synchronization. 7. restore(13) -indicates the trap type is restore alarm from alarm synchronization. 8. unrestored(14)-indicates the trap type is unrestored alarm from alarm synchronization. 9. datachange(15)-indicates the trap type is data change trap. There are two types of trap in the system: 1. Alarm trap. The alarm trap including alarms and events, options as: alarm(2), fault(12), restore(13) and unrestored(14), only alarm trap can include hwNotificationType. The format of an alarm trap is as follows: ------------------------------------------------------------------------ \| PDU Type \| RequestID \| ErrorStatus \| ErrorIndex \| Variable-bindings \| ------------------------------------------------------------------------ The format of Variable-bindings in alarm type is as follows: ---------------------------------------------------------------------------------------------------------------------------------------------------------------------- \| sysUpTime \| snmpTrapOID \| TrapSN \| InfoLevel \| Specific-trap \| Agent-addr \| AlarmID \| AlarmSN \| CauseID \| Type \| Time \| AlmText \| CauseText \| userLabel \| Paras... \| ---------------------------------------------------------------------------------------------------------------------------------------------------------------------- 2. Non-alarm trap. The non-alarm trap including the maintain, test, topology and datachange trap, options as: maintain(2), standard(12), topo(13), test(14) and datachange(15). The format of a non-alarm trap is as follows: ------------------------------------------------------------------------ \| PDU Type \| RequestID \| ErrorStatus \| ErrorIndex \| Variable-bindings \| ------------------------------------------------------------------------ The format of Variable-bindings in non-alarm trap is as follows: ------------------------------------------------------------------------------------------------------------------- \| sysUpTime \| snmpTrapOID \| TrapSN \| InfoLevel \| Specific-trap \| Agent-addr \| TrapID \| Para-0 \| Para-1 \| Paras... \| -------------------------------------------------------------------------------------------------------------------
NTF hwSynAlarm	1.3.6.1.4.1.2011.6.30.2.2.0.1			Currently, the object is not supported. This trap is reported when syn operation from NMS.
hwSynMibTrap	1.3.6.1.4.1.2011.6.30.2
hwSyntrap	1.3.6.1.4.1.2011.6.30			This MIB object is used to describe the interfaces of sending the host notifications (including the alarm and event), and configurations of the log, syslog and trap.
hwSynTrapOid	1.3.6.1.4.1.2011.6.30.2.1
hwSynTraps	1.3.6.1.4.1.2011.6.30.2.2.0
hwSynTrapsDefine	1.3.6.1.4.1.2011.6.30.2.2
INT hwSyslogFacility	1.3.6.1.4.1.2011.6.30.5.2	INTEGER	read-write	Description of the facility of the output syslog information. Options: 1. local0(1) -indicates that the syslog facility is local0. 2. local1(2) -indicates that the syslog facility is local1. 3. local2(3) -indicates that the syslog facility is local2. 4. local3(4) -indicates that the syslog facility is local3. 5. local4(5) -indicates that the syslog facility is local4. 6. local5(6) -indicates that the syslog facility is local5. 7. local6(7) -indicates that the syslog facility is local6. 8. local7(8) -indicates that the syslog facility is local7. 9. default(9) -indicates that the syslog facility is not set yet. The system provides eight facility from local0(1) to local7(8) to config the syslog facility. The default(9) indicates that the syslog facility is not set yet. When the value is default(9), the facility of operating syslog or security syslog is local0, and the facility of alarm/event syslog is associate with the alarm/event type as follows: ALARM TYPE FACILITY 1. COMMUNICATION local0 2. SERVICE QUALITY local1 3. PROCESS ERROR local2 4. EQUIPMENT local3 5. ENVIRONMENTAL local4
hwSyslogHostEntry	1.3.6.1.4.1.2011.6.30.14.2.1		not-accessible	Syslog host table. It is used to set attribute of syslog host in the current system. The index of this table is hwSyslogHostName.
BIT hwSyslogHostFacility	1.3.6.1.4.1.2011.6.30.14.2.1.4	Bits	read-write	List of the syslog host facility. Through this object, the syslog host facility can be configured in batches in the format of bit-domain string. The syslog host facility hwSyslogHostFacility is of the bit type. The value indicated that an operation is performed based on bits. When the bit is set to 1, the messages of the bit are collected. local0 indicates bit 16, local1 indicates bit 17,... and local7 indicates bit 23.
IP hwSyslogHostInetAddress	1.3.6.1.4.1.2011.6.30.14.2.1.3	IpAddress	read-write	IP address of the syslog host.
INT hwSyslogHostInetAddressType	1.3.6.1.4.1.2011.6.30.14.2.1.2	INTEGER	read-write	Obtained version of internet address. Options: 1. ipv4(1) -indicates that the internet address version is IPv4. 2. ipv6(2) -indicates that the internet address version is IPv6.
OCT hwSyslogHostName	1.3.6.1.4.1.2011.6.30.14.2.1.1	OCTET STRING	not-accessible	Syslog host name,a kind of string parameter. Index of hwSyslogHostTable.
ROW hwSyslogHostRowStatus	1.3.6.1.4.1.2011.6.30.14.2.1.5	RowStatus	read-create	The status of this conceptual row. active(1) indicates that the log host is set to the activated state. notInservice(2) indicates that the log host is set to the deactivated state. createandgo(4) indicates that the log host is created and it is the deactivated state by default. destroy(6) indicates that a specific log host is deleted.
hwSyslogHostTable	1.3.6.1.4.1.2011.6.30.14.2		not-accessible	Syslog host table. It is used to set attribute of syslog host in the current system. The index of this table is hwSyslogHostName.
INT hwSyslogLevelIndex	1.3.6.1.4.1.2011.6.30.5.1.1.1	INTEGER	read-only	Description of the level of the output syslog information. Currently, the syslog supports eight data types. Options: 1. emergency(1) -indicates that system is unusable. 2. alert(2) -indicates that action must be taken immediately. 3. critical(3) -indicates that critical conditions. 4. error(4) -indicates that error conditions. 5. warning(5) -indicates that warning conditions. 6. notice(6) -indicates that normal but significant condition. 7. informational(7) -indicates that informational messages. 8. debug(8) -indicates that debug-level messages.
INT hwSyslogLogFacility	1.3.6.1.4.1.2011.6.30.5.4.1.2	INTEGER	read-write	Description of the facility of the output syslog information. Options: 1. local0(1) -indicates that the syslog facility is local0. 2. local1(2) -indicates that the syslog facility is local1. 3. local2(3) -indicates that the syslog facility is local2. 4. local3(4) -indicates that the syslog facility is local3. 5. local4(5) -indicates that the syslog facility is local4. 6. local5(6) -indicates that the syslog facility is local5. 7. local6(7) -indicates that the syslog facility is local6. 8. local7(8) -indicates that the syslog facility is local7. 9. default(9) -indicates that the syslog facility is not set yet. The system provides eight facility from local0(1) to local7(8) to config the syslog facility. The default(9) indicates that the syslog facility is not set yet. When the value is default(9), the facility of operating syslog or security syslog is local0, and the facility of alarm/event syslog is associate with the alarm/event type as follows: ALARM TYPE FACILITY 1. COMMUNICATION local0 2. SERVICE QUALITY local1 3. PROCESS ERROR local2 4. EQUIPMENT local3 5. ENVIRONMENTAL local4
hwSysloglogFacilityEntry	1.3.6.1.4.1.2011.6.30.5.4.1		not-accessible	Log facility of the current syslog. The index of this entry is hwSyslogLogType. hwSyslogLogType is used to describe the type of the syslog.
hwSysloglogFacilityTable	1.3.6.1.4.1.2011.6.30.5.4		not-accessible	Log facility of the current syslog. The index of this entry is hwSyslogLogType. hwSyslogLogType is used to describe the type of the syslog.
INT hwSyslogLogSeverity	1.3.6.1.4.1.2011.6.30.5.4.1.3	INTEGER	read-write	Description of the severity of the output syslog information. Options: 1. emergency(1) -indicates that system is unusable. 2. alert(2) -indicates that action must be taken immediately. 3. critical(3) -indicates that critical conditions. 4. error(4) -indicates that error conditions. 5. warning(5) -indicates that warning conditions. 6. notice(6) -indicates that normal but significant condition. 7. informational(7) -indicates that informational messages. 8. debug(8) -indicates that debug messages. 9. default(9) -indicates that the severity of syslog is not set yet. The system provides eight level from emergency(1) to debug(8) to config the syslog severity. The default(9) indicates that the syslog severity is not set yet. When the value is default(9), the severity of operating syslog or security syslog is informational(7), and the severity of alarm/event syslog is associate with the alarm/event level as follows: ALARM LEVEL SEVERITY 1. CRITICAL alert 2. MAJOR critical 3. MINOR warning 4. WARNING informational 5. CLEARED notice
INT hwSyslogLogType	1.3.6.1.4.1.2011.6.30.5.4.1.1	INTEGER	not-accessible	Description of the type of the output syslog information. Options: 1. log(1) -indicates that the syslog type is log. 2. alarm-event(2) -indicates that the syslog type is alarm-event. 3. igmp(3) -indicates that the syslog type is igmp.
hwSyslogOutput	1.3.6.1.4.1.2011.6.30.5
hwSyslogOutputEntry	1.3.6.1.4.1.2011.6.30.5.1.1		not-accessible	Levels of the all the logs supported by the current syslog. The index of this entry is hwSyslogLevelIndex. hwSyslogLevelIndex is used to describe of the level of the output syslog information.
INT hwSyslogOutputOperStatus	1.3.6.1.4.1.2011.6.30.5.1.1.2	INTEGER	read-write	The output status of the syslog information. Options: 1. unoutput(1) -indicates that the syslog information is not output to the local PC or server. 2. output(2) -indicates that the syslog information is output to the terminal and server.
hwSyslogOutputTable	1.3.6.1.4.1.2011.6.30.5.1		not-accessible	Levels of the all the logs supported by the current syslog. The index of this table is hwSyslogLevelIndex. hwSyslogLevelIndex is used to describe of the level of the output syslog information.
INT hwSyslogSeverity	1.3.6.1.4.1.2011.6.30.5.3	INTEGER	read-write	Description of the severity of the output syslog information. Options: 1. emergency(1) -indicates that system is unusable. 2. alert(2) -indicates that action must be taken immediately. 3. critical(3) -indicates that critical conditions. 4. error(4) -indicates that error conditions. 5. warning(5) -indicates that warning conditions. 6. notice(6) -indicates that normal but significant condition. 7. informational(7) -indicates that informational messages. 8. debug(8) -indicates that debug messages. 9. default(9) -indicates that the severity of syslog is not set yet. The system provides eight level from emergency(1) to debug(8) to config the syslog severity. The default(9) indicates that the syslog severity is not set yet. When the value is default(9), the severity of operating syslog or security syslog is informational(7), and the severity of alarm/event syslog is associate with the alarm/event level as follows: ALARM LEVEL SEVERITY 1. CRITICAL alert 2. MAJOR critical 3. MINOR warning 4. WARNING informational 5. CLEARED notice
NTF hwTargetHostDeletedTrap	1.3.6.1.4.1.2011.6.30.18.2.0.3			This trap message is reported when the destination host of the trap message is deleted.
I32 hwTrapBufferMaxSn	1.3.6.1.4.1.2011.6.30.11.1.1.3	Integer32	read-only	Maximum serial number of the trap in the trap buffer area.
I32 hwTrapBufferMinSn	1.3.6.1.4.1.2011.6.30.11.1.1.2	Integer32	read-only	Minimum serial number of the trap in the trap buffer area.
hwTrapConfig	1.3.6.1.4.1.2011.6.30.16
hwTrapFlowCtrl	1.3.6.1.4.1.2011.6.30.10
INT hwTrapFlowCtrlSwitch	1.3.6.1.4.1.2011.6.30.10.1	INTEGER	read-write	Trap traffic control. In certain cases, the alarm module receives the alarm reported by the service module, processes the alarm and then reports the alarm to the NMS. When multiple alarms are reported, the trap traffic in the system increases suddenly. As a result, the NMS is affected and the trap may be lost. Therefore, a buffer function is added to the system to solve the problem. The function is called trap traffic control. This object is used to configure the function. Options: 1. on(1) -indicates that you need to enable trap traffic control. The traffic control is started. 2. off(2)-indicates that you need to disable trap traffic control. The traffic control is stopped.
INT hwTrapFormatMode	1.3.6.1.4.1.2011.6.30.16.1	INTEGER	read-write	The format of the reported trap. Options: 1. standard(1) -The trap message is in the standard format. 2. private(2) -The trap message is in the private format. DEFVAL { private }.
I32 hwTrapID	1.3.6.1.4.1.2011.6.30.17.1	Integer32	accessible-for-notify	Trap ID.
INT hwTrapLevel	1.3.6.1.4.1.2011.6.30.17.3	INTEGER	accessible-for-notify	Trap level, indicates the significance of trap. Options: 1. critical(1) -indicates the trap level is critical. 2. major(2) -indicates the trap level is major. 3. minor(3) -indicates the trap level is minor. 4. warning(4) -indicates the trap level is warning. 5. cleared(5) -indicates the trap level is cleared. 6. indeterminate(6)-indicates the trap level is indeterminate. 7. notalarmed(7) -indicates the trap level is notalarmed. 8. reliable(8) -indicates the trap level is reliable.
I32 hwTrapNum	1.3.6.1.4.1.2011.6.30.17.12	Integer32	accessible-for-notify	Number of synchronized trap messages.
INT hwTrapOperType	1.3.6.1.4.1.2011.6.30.17.17	INTEGER	accessible-for-notify	This object indicates the operation type. Options: 1. add(1) - Add 2. modify(2) - Modify 3. delete(3) - Delete
hwTrapReliability	1.3.6.1.4.1.2011.6.30.19
hwTrapReliabilityConfEntry	1.3.6.1.4.1.2011.6.30.19.1.1		not-accessible	Trap reliablity table. It is used to set the reliable trap through the NMS. The indexes of this entry are hwTrapReliabilityTrapType and hwTrapReliabilityTrapID.
ROW hwTrapReliabilityConfRowStatus	1.3.6.1.4.1.2011.6.30.19.1.1.3	RowStatus	read-create	The status of this conceptual row. createAndGo(4) is supplied to create a new instance of a conceptual row. destroy(6) is supplied to delete the instances associated with an existing conceptual row.
hwTrapReliabilityConfTable	1.3.6.1.4.1.2011.6.30.19.1		not-accessible	Trap reliablity table. It is used to set the reliable trap through the NMS. The indexes of this table are hwTrapReliabilityTrapType and hwTrapReliabilityTrapID.
I32 hwTrapReliabilityTrapID	1.3.6.1.4.1.2011.6.30.19.1.1.2	Integer32	not-accessible	Reliable trap ID, the range is 1-0xffffffff.
INT hwTrapReliabilityTrapType	1.3.6.1.4.1.2011.6.30.19.1.1.1	INTEGER	not-accessible	Reliable trap types. Options: 1. maintain(3) -indicates the maintenance trap. 2. snmpstd(4) -indicates the standard trap. 3. topo(5) -indicates the topological trap. 4. test(6) -indicates the test trap. 5. datachange(15)-indicates the data change trap.
U32 hwTrapReliablityTrapSnConfirm	1.3.6.1.4.1.2011.6.30.19.2	Unsigned32	read-write	Serial number of the trap confirmed by the NMS. When get this leaf, the value is alwayse -1 and any serial number set will be successful.
I32 hwTrapSN	1.3.6.1.4.1.2011.6.30.17.2	Integer32	accessible-for-notify	Serial number of the trap in the current system.
hwTrapSyn	1.3.6.1.4.1.2011.6.30.11
OCT hwTrapSynActiveAlarmList	1.3.6.1.4.1.2011.6.30.11.3	OCTET STRING	read-write	Serial number list of the active alarm to be synchronized to NMS.
INT hwTrapSynAdminStatus	1.3.6.1.4.1.2011.6.30.11.1.1.6	INTEGER	read-write	Trap synchronization management status. Options: 1. other(1) -other. 2. stop(2) -stop. 3. interval(3) -indicates the traps with the serial numbers in the range of the synchronization serial numbers are synchronized. In this case, you must specify the index and issue the starting serial number of trap and the ending serial number of trap. 4. all(4) -indicates that all the traps are synchronized. In this case, you can only specify the index and issue the last object 5. intervalsynfile(5)-indicates that the traps with specified serial numbers form to a file and then the file is synchronized. In this case, you must specify the index and issue the starting serial number of trap that is synchronized and the ending serial number of trap that is synchronized. 6. allsynfile(6) -indicates that all the traps form to a file and then the file is synchronized. In this case, you can only specify the index and issue the last object.
I32 hwTrapSynBeginSn	1.3.6.1.4.1.2011.6.30.11.1.1.4	Integer32	read-write	Starting serial number of the trap that is synchronized. The value is the serial number of the trap in the trap buffer area and can be obtained through hwTrapBufferMinSn and hwTrapBufferMaxSn. The hwTrapSynBeginSn value of -1 indicates there is no trap synchronizing.
I32 hwTrapSynEndSn	1.3.6.1.4.1.2011.6.30.11.1.1.5	Integer32	read-write	Ending serial number of trap that is synchronized. The value is the serial number of the trap in the trap buffer area and can be obtained through hwTrapBufferMinSn and hwTrapBufferMaxSn. The hwTrapSynEndSn value of -1 indicates there is no trap synchronizing.
hwTrapSynEntry	1.3.6.1.4.1.2011.6.30.11.1.1		not-accessible	Trap synchronization table. The trap synchronization function is used to send the trap buffered in the system to the trap host in a file or in the synchronization mode. The index of this entry is hwTrapSynType, indicating the type of the trap synchronization.
hwTrapSynTable	1.3.6.1.4.1.2011.6.30.11.1		not-accessible	Trap synchronization table. The trap synchronization function is used to send the trap buffered in the system to the trap host in a file or in the synchronization mode. The index of this table is hwTrapSynType, indicating the type of the trap synchronization.
INT hwTrapSynType	1.3.6.1.4.1.2011.6.30.11.1.1.1	INTEGER	not-accessible	Trap synchronization types. Options: 1. trap(1) -indicates that all the traps are synchronized. 2. alarm(2) -indicates that only the alarm trap is synchronized. 3. alarmSub(3) -indicates that the alarm trap is synchronized by synchronization ID. The value of alarmSub can be obtained through hwTrapBufferMinSn or hwTrapBufferMaxSn.
BIT hwTrapTypeSynSwitch	1.3.6.1.4.1.2011.6.30.11.2	Bits	read-write	The switch of all types of info for trap synchronization. Function of the trap synchronization. It is controlled by the bit. The issued value is ULONG and is controlled by the first eight bits. The following part uses the eight bits as an example. Options: 1. event(0) -indicates that the corresponding bits are 10000000. 2. alarm(1) -indicates that the corresponding bits are 1000000. 3. maintain(2) -indicates that the corresponding bits are 100000. 4. topo(4) -indicates that the corresponding bits are 1000. 5. test(5) -indicates that the corresponding bits are 100. 6. datachange(6) -indicates that the corresponding bits are 10.
hwTrapVbOids	1.3.6.1.4.1.2011.6.30.17
OCT hwUserLabel	1.3.6.1.4.1.2011.6.30.17.6	OCTET STRING	accessible-for-notify	Alarm or event user label, a kind of string parameter.

RFC description

SNMP notification configuration including trap targets, syslog hosts, and alarm synchronization.

Start monitoring Huawei router or switch (alarm/event/trap notification delivery config) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-SNMP-NOTIFICATION-MIB

What Is HUAWEI-SNMP-NOTIFICATION-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description