HUAWEI-LOAD-BACKUP-MIB

All MIBs › HUAWEI-LOAD-BACKUP-MIB

Organization: Fix-Net Dep, Huawei Technologies Co.,Ltd.

Last Updated: 2003-04-28

Category: Device Management, Domain: WAN, Vendor: Huawei

Description: Huawei load backup MIB for managing primary/secondary link failover and load-balancing backup policies on Huawei WAN and access routers.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-LOAD-BACKUP-MIB?

HUAWEI-LOAD-BACKUP-MIB is a Huawei enterprise MIB used to manage primary/secondary WAN link failover and load-balancing backup policies on Huawei routers and access platforms. It is expected to expose configuration objects that define backup link relationships, load-sharing weights or thresholds, and the operational state of the active versus standby paths. Although no object names were supplied to confirm this, MIBs in this "load and backup" family typically let an administrator monitor which link is currently active, whether a failover event has occurred, and how traffic load is distributed across redundant paths, functioning as a software/link-status health check rather than a hardware sensor MIB. It likely builds on the standard IF-MIB ifIndex convention to associate backup policies with specific WAN interfaces. This MIB is deployed in Huawei WAN/branch-office routers that use dual-link or multi-link backup for internet or MPLS connectivity resilience. Engineers can download the HUAWEI-LOAD-BACKUP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-LOAD-BACKUP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei WAN/access routers with dual-link backup configuration

Monitoring Examples

No sample objects were included for this module, so the exact table/object names polled cannot be confirmed; a typical deployment would involve polling a link-status or backup-policy table to detect whether the router has switched from its primary WAN link to the backup link, but this cannot be grounded in real object names here.

Imported Objects

From HUAWEI-DEVICE-MIB

hwFrameIndex	OBJECT-TYPE
hwSlotIndex	OBJECT-TYPE

From HUAWEI-MIB

huaweiUtility

OBJECT-IDENTITY

From HUAWEI-TC-MIB

HWPCBType

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
hwLoadBackup	1.3.6.1.4.1.2011.6.6			Huawei load and backup mib.
hwLoadBackupMon	1.3.6.1.4.1.2011.6.6.1
hwLoadParaTable	1.3.6.1.4.1.2011.6.6.1.1		not-accessible	The load parameter table.
hwLoadParaEntry	1.3.6.1.4.1.2011.6.6.1.1.1		not-accessible	The load parameter table entry.
IP hwLoadServerIpAddr	1.3.6.1.4.1.2011.6.6.1.1.1.1	IpAddress	read-write	The IP address of server.
INT hwLoadMode	1.3.6.1.4.1.2011.6.6.1.1.1.2	INTEGER	read-write	The load protocol.
STR hwLoadFileName	1.3.6.1.4.1.2011.6.6.1.1.1.3	DisplayString	read-write	The file name.
INT hwLoadContent	1.3.6.1.4.1.2011.6.6.1.1.1.4	INTEGER	read-write	Load content: enum explanation ********************************************** program(1), -- program file configuration(2), -- configuration file patch(3), -- patch file shellMacro(4), resLocal(5), resGeneral(6), cpeDrive(7), programDatabase(8), -- database file programBios(9), -- bios file programApp(10), -- application program logicFpga(11), -- fpga logic file logicCpld(12), -- Cpld logic file logicPci(13), -- pci logic file logicAfc(14), -- afc logic file programMicroCode(15), -- micro code file programFirmware(16), -- application program of pinch board programHelp(17), programDataFlow(18), -- flow file of card management point programBootFile(19), -- Boot program file of board logciPa(20), -- Boot program file of board start webExp(21), -- web exp file web exp webNev(22), -- web nev file web nev webHelp(23), -- web help file web programBsp(24), -- bsp program file bsp configurationIni(40), -- configuration file of ini formatini configurationEfs(41), -- configuration file with the header of efs configurationCli(42), -- configuration file of command line format programCurrent(45), -- the program being run programOther(46), -- the program that has not been run presently license(49), -- license file programchipset(50), -- AC5 chipset load
HWP hwLoadBoardType	1.3.6.1.4.1.2011.6.6.1.1.1.5	HWPCBType	read-write	The board type the system supports.
I32 hwPortId	1.3.6.1.4.1.2011.6.6.1.1.1.6	Integer32	read-write	The port index.
I32 hwLoadProcess	1.3.6.1.4.1.2011.6.6.1.1.1.7	Integer32	read-only	The Process of loading.
STR hwLoadUserName	1.3.6.1.4.1.2011.6.6.1.1.1.8	DisplayString	read-write	The load user namewhich is necessary in FTP mode and unnecessary in TFTP mode.
STR hwLoadPassword	1.3.6.1.4.1.2011.6.6.1.1.1.9	DisplayString	read-write	The load user name,which is necessary in FTP mode , which is necessary in FTP mode and unnecessary in TFTP mode.
hwBackupParaTable	1.3.6.1.4.1.2011.6.6.1.2		not-accessible	The backup parameter table.
hwBackupParaEntry	1.3.6.1.4.1.2011.6.6.1.2.1		not-accessible	The backup parameter table entry.
IP hwBackupServerIpAddr	1.3.6.1.4.1.2011.6.6.1.2.1.1	IpAddress	read-write	The IP address of Server
INT hwBackupMode	1.3.6.1.4.1.2011.6.6.1.2.1.2	INTEGER	read-write	Load protocol:tftp and MODEM currently supported.
STR hwBackupFileName	1.3.6.1.4.1.2011.6.6.1.2.1.3	DisplayString	read-write	The file name.
INT hwBackupContent	1.3.6.1.4.1.2011.6.6.1.2.1.4	INTEGER	read-write	The backup content.
I32 hwBackupProcess	1.3.6.1.4.1.2011.6.6.1.2.1.5	Integer32	read-only	The Process of backuping.
STR hwBackupUserName	1.3.6.1.4.1.2011.6.6.1.2.1.6	DisplayString	read-write	The backup user namewhich is necessary in FTP mode and unnecessary in TFTP mode.
STR hwBackupPassword	1.3.6.1.4.1.2011.6.6.1.2.1.7	DisplayString	read-write	The backup user name,which is necessary in FTP mode , which is necessary in FTP mode and unnecessary in TFTP mode.
HWP hwBackupBoardType	1.3.6.1.4.1.2011.6.6.1.2.1.8	HWPCBType	read-write	The type of backup board.
snmpTraps	1.3.6.1.4.1.2011.6.6.1.3
hwLoadAndBackupTrapsOID	1.3.6.1.4.1.2011.6.6.1.3.0
NTF hwBackupFailAlarm	1.3.6.1.4.1.2011.6.6.1.3.0.1			The back up failure alarm trap.
NTF hwLoadFailAlarm	1.3.6.1.4.1.2011.6.6.1.3.0.2			The load failure alarm trap.
NTF hwBackupFailAlarmSuccess	1.3.6.1.4.1.2011.6.6.1.3.0.3			The backup success notification.
NTF hwLoadFailAlarmSuccess	1.3.6.1.4.1.2011.6.6.1.3.0.4			The load success notification.
NTF hwCopyAndSaveFail	1.3.6.1.4.1.2011.6.6.1.3.0.5			Save configuration to flash failure trap.
NTF hwCopyAndSaveSuccess	1.3.6.1.4.1.2011.6.6.1.3.0.6			Save configuration to flash success notification .
NTF hwConfigurationChangedEvent	1.3.6.1.4.1.2011.6.6.1.3.0.7			The configuration changed event alarm.
hwTrapCauseOids	1.3.6.1.4.1.2011.6.6.1.3.1
hwTrapLoadBackupResult	1.3.6.1.4.1.2011.6.6.1.3.1.1
I32 hwTrapLoadResult	1.3.6.1.4.1.2011.6.6.1.3.1.1.1	Integer32	accessible-for-notify	The load result.
I32 hwTrapBackupResult	1.3.6.1.4.1.2011.6.6.1.3.1.1.2	Integer32	accessible-for-notify	Definition node of the backup failure cause.
INT hwCopyAndSaveResult	1.3.6.1.4.1.2011.6.6.1.3.1.1.3	INTEGER	accessible-for-notify	The failure cause definition node of the memory running copy and resume.
hwTrapEventCauses	1.3.6.1.4.1.2011.6.6.1.3.1.2
INT hwConfEventCause	1.3.6.1.4.1.2011.6.6.1.3.1.2.1	INTEGER	accessible-for-notify	The configuration changed cause.
hwBackupAndRestoreConfig	1.3.6.1.4.1.2011.6.6.1.4
INT hwBackupAndRestore	1.3.6.1.4.1.2011.6.6.1.4.1	INTEGER	read-write	The running configuration in the system has been backup to flash or disk, or been restored from .
hwPatch	1.3.6.1.4.1.2011.6.6.2
hwPatchTable	1.3.6.1.4.1.2011.6.6.2.1		not-accessible	The operation and enquiry table of patch.
hwPatchEntry	1.3.6.1.4.1.2011.6.6.2.1.1		not-accessible	The operation and enquiry table entry of patch.
U32 hwPatchId	1.3.6.1.4.1.2011.6.6.2.1.1.1	Unsigned32	not-accessible	The patch number.
STR hwPatchDescription	1.3.6.1.4.1.2011.6.6.2.1.1.2	DisplayString	read-only	The description of patch.
I32 hwPatchFuncNum	1.3.6.1.4.1.2011.6.6.2.1.1.3	Integer32	read-only	The number of functions in patch.
I32 hwPatchTextLen	1.3.6.1.4.1.2011.6.6.2.1.1.4	Integer32	read-only	The length of patch code.
I32 hwPatchDataLen	1.3.6.1.4.1.2011.6.6.2.1.1.5	Integer32	read-only	The length of patch data.
INT hwPatchType	1.3.6.1.4.1.2011.6.6.2.1.1.6	INTEGER	read-only	The type of patch.
INT hwPatchAdminStatus	1.3.6.1.4.1.2011.6.6.2.1.1.7	INTEGER	read-write	The operation of patch.
INT hwPatchOperState	1.3.6.1.4.1.2011.6.6.2.1.1.8	INTEGER	read-only	The station of patch.
hwPatchStatTable	1.3.6.1.4.1.2011.6.6.2.2		not-accessible	The table of statistics information of patch.
hwPatchStatEntry	1.3.6.1.4.1.2011.6.6.2.2.1		not-accessible	The table entry of statistics information of patch.
I32 hwPatchStatNumMax	1.3.6.1.4.1.2011.6.6.2.2.1.1	Integer32	read-only	The maximum patch number of system.
I32 hwPatchStatTextMax	1.3.6.1.4.1.2011.6.6.2.2.1.2	Integer32	read-only	The capacity of patch code area.
I32 hwPatchStatDataMax	1.3.6.1.4.1.2011.6.6.2.2.1.3	Integer32	read-only	The capacity of patch data area.
I32 hwPatchStatTextUsed	1.3.6.1.4.1.2011.6.6.2.2.1.4	Integer32	read-only	The used patch code area.
I32 hwPatchStatDataUsed	1.3.6.1.4.1.2011.6.6.2.2.1.5	Integer32	read-only	The used patch data area.
hwLoadBackupConformance	1.3.6.1.4.1.2011.6.6.3
hwLoadBackupCompliances	1.3.6.1.4.1.2011.6.6.3.1
hwLoadBackupCompliance	1.3.6.1.4.1.2011.6.6.3.1.1			The compliance statement for systems supporting the this module.
hwLoadBackupObjectGroups	1.3.6.1.4.1.2011.6.6.3.2
hwLoadParaTableGroup	1.3.6.1.4.1.2011.6.6.3.2.1			The load parameter group objects.
hwBackupParaTableGroup	1.3.6.1.4.1.2011.6.6.3.2.2			The backup parameter group objects.
hwTrapEventCausesGroup	1.3.6.1.4.1.2011.6.6.3.2.3			The trap event causes group objects.
hwTrapLoadBackupResultGroup	1.3.6.1.4.1.2011.6.6.3.2.4			The load and backup result group objects.
hwTrapLoadBackupTrapsGroup	1.3.6.1.4.1.2011.6.6.3.2.5			The load and backup traps group objects.
hwBackupAndRestoreConfigGroup	1.3.6.1.4.1.2011.6.6.3.2.6			The load and backup config group objects.
hwPatchTableGroup	1.3.6.1.4.1.2011.6.6.3.2.7			The patch table group objects.
hwPatchStatTableGroup	1.3.6.1.4.1.2011.6.6.3.2.8			The patch statistics group objects.

RFC description

Manages load balancing and backup configurations on Huawei network devices.

Start monitoring Huawei WAN/access router with dual-link backup with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-LOAD-BACKUP-MIB

What Is HUAWEI-LOAD-BACKUP-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description