All MIBs › HUAWEI-BTEST-MIB
Organization: Huawei Technologies Co.,Ltd.
Last Updated: 2012-01-09
Category: Domain: DSL, Vendor: Huawei
Description: Huawei broadband test MIB providing objects to initiate and monitor diagnostic tests on subscriber DSL lines and broadband access interfaces.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HUAWEI-BTEST-MIB?
HUAWEI-BTEST-MIB is a Huawei enterprise MIB (under huaweiUtility, hwTest) that models the Broadband Test Subsystem (BTSS) used to run diagnostic tests on subscriber DSL lines and broadband access ports, such as central-office (CO) emulation tests, CQT transparent-command tests, and Single-Ended Line Test (SELT) for ADSL2+. It exposes per-port test control and results through tables like hwBTSSCoTestTable (start/stop CO emulation, pass/fail result), hwBTSSTestedPortOperTable (capture/release/monitor operations on a tested port), and hwBTSSAdslSeltTestTable, which returns detailed SELT physical-layer measurements (loop length, loop termination state, loop gauge, Shannon capacity, echo response, inband noise) indexed by ifIndex. This lets an operator remotely diagnose DSL line quality and connectivity issues (e.g., estimating loop length or detecting an open/shorted line) without a truck roll. It depends on HUAWEI-DEVICE-MIB for frame/slot indexing and HUAWEI-COMMTEST-MIB for the shared hwTestGroupNo index used by auxiliary test ports. It is deployed on Huawei broadband access platforms (DSLAMs/MSANs) supporting xDSL line testing, and engineers can download the HUAWEI-BTEST-MIB file to add DSL diagnostics to their monitoring toolchain.
IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-BTEST-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Huawei broadband access platforms (DSLAM/MSAN) supporting xDSL line diagnostics
Monitoring Examples
An operator sets hwBTSSAdslSeltTestOperType to start(2) on a subscriber's ifIndex and then polls hwBTSSAdslSeltTestOperResult and hwBTSSAdslSeltTestParamLoopTermin; a result of fail(2) or a loop termination state of short(1) or open(0) would indicate a physical fault on the copper pair before a technician is dispatched.
What Can Be Monitored
- CO emulation test start/stop and result
- tested-port capture/release/monitor operations
- SELT test operation status and result
- loop length, termination state, and gauge measurements
- upstream/downstream Shannon capacity and margin-vs-rate data
- CQT transparent-command test results
This MIB depends on
Related MIBs
Imported Objects
From HUAWEI-COMMTEST-MIB
| hwTestGroupNo | OBJECT-TYPE |
From HUAWEI-DEVICE-MIB
| hwFrameIndex | OBJECT-TYPE |
| hwSlotIndex | OBJECT-TYPE |
From HUAWEI-MIB
| huaweiUtility | OBJECT-IDENTITY |
From HUAWEI-TC-MIB
| HWPortType |
From IF-MIB
| ifIndex | OBJECT-TYPE |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| RowStatus | |
| TEXTUAL-CONVENTION |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hwTest | 1.3.6.1.4.1.2011.6.21 | |||
| hwBTest | 1.3.6.1.4.1.2011.6.21.3 | This MIB is used for defining Huawei's BTEST MIB objects,which is used for Broad test. | ||
| hwBTestMib | 1.3.6.1.4.1.2011.6.21.3.1 | |||
| hwBTestMIBObjects | 1.3.6.1.4.1.2011.6.21.3.1.1 | |||
| hwBTSSxDslLineCfgTable | 1.3.6.1.4.1.2011.6.21.3.1.1.1 | not-accessible | The hwBTSSxDslLineCfgTable table describes xDSL line configuration. This table is used for bandwidth test. The index of this table is ifIndex. | |
| hwBTSSxDslLineCfgEntry | 1.3.6.1.4.1.2011.6.21.3.1.1.1.1 | not-accessible | The hwBTSSxDslLineCfgTable table describes xDSL line configuration. This table is used for bandwidth test. The index of this entry is ifIndex. | |
| HWB hwBTSSxDslLineOverlapType | 1.3.6.1.4.1.2011.6.21.3.1.1.1.1.1 | HWBTSSxDslLineOverLap | read-write | Overlap mode of xDSL with PSTN line. Options: 1. overLap(1) - xDSL overlap with POTS line 2. direct(2) - There is no pots line, no splitter, no phone 3. unknown(3) - The mode is unknown Default: unknown(3) |
| hwBTSSCoTestTable | 1.3.6.1.4.1.2011.6.21.3.1.1.2 | not-accessible | xDSL central office emulational measurement table.The table is used for xDSL central emulational measurement. The index of this table is ifIndex. | |
| hwBTSSCoTestEntry | 1.3.6.1.4.1.2011.6.21.3.1.1.2.1 | not-accessible | xDSL central office emulational measurement table.The table is used for xDSL central emulational measurement. The index of this entry is ifIndex. | |
| INT hwBTSSCoOperType | 1.3.6.1.4.1.2011.6.21.3.1.1.2.1.1 | INTEGER | read-write | CO emulational operation type. Options: 1. stop(1) - Stop CO emulational 2. start(2) - Start CO emulational |
| INT hwBTSSCoTestResult | 1.3.6.1.4.1.2011.6.21.3.1.1.2.1.2 | INTEGER | accessible-for-notify | CO emulational test result. Options: 1. normal(1) - The test of CO emulational is successful 2. testfail(2) - Fail in test of CO emulational |
| INT hwBTSSCoTestBusyFlag | 1.3.6.1.4.1.2011.6.21.3.1.1.2.1.3 | INTEGER | read-write | CO force test flag Options: 1. busyNoTest(1) - No test on busy 2. busyTest(2) - Test on busy 3. busystrenTest(3) - Forced test on busy |
| hwBTSSAuxPortCfgTable | 1.3.6.1.4.1.2011.6.21.3.1.1.17 | not-accessible | Configuration table of the broadband test auxiliary port This table is used to configure a certain type of emulation port required in the CO emulation test. The indexes of this table are hwTestGroupNo and hwBTSSAuxPortType. | |
| hwBTSSAuxPortCfgEntry | 1.3.6.1.4.1.2011.6.21.3.1.1.17.1 | not-accessible | Configuration table of the broadband test auxiliary port This table is used to configure a certain type of emulation port required in the CO emulation test. The indexes of this entry are hwTestGroupNo and hwBTSSAuxPortType. | |
| INT hwBTSSAuxPortType | 1.3.6.1.4.1.2011.6.21.3.1.1.17.1.1 | INTEGER | not-accessible | Assistance port type of BTSS. Options: 1. adsl(1) - Assistance port type of BTSS is adsl 2. vdsl(2) - Assistance port type of BTSS is vdsl 3. gshdsl(3) - Assistance port type of BTSS is gshdsl |
| I32 hwBTSSAuxPortIfIndex | 1.3.6.1.4.1.2011.6.21.3.1.1.17.1.2 | Integer32 | read-create | Assistance port ifIndex of BTSS. |
| ROW hwBTSSAuxPortRowStatus | 1.3.6.1.4.1.2011.6.21.3.1.1.17.1.3 | RowStatus | read-create | Row status(add(4),delete(6)). |
| hwBTSSTestedPortOperTable | 1.3.6.1.4.1.2011.6.21.3.1.1.18 | not-accessible | This table describes operation for tested port. The index of this table is ifIndex. | |
| hwBTSSTestedPortOperEntry | 1.3.6.1.4.1.2011.6.21.3.1.1.18.1 | not-accessible | This table describes operation for tested port. The index of this entry is ifIndex. | |
| INT hwBTSSTestedPortOperType | 1.3.6.1.4.1.2011.6.21.3.1.1.18.1.1 | INTEGER | read-write | Operation type of BTSS tested port. Options: 1. capture(1) - Capture 2. release(2) - Release 3. startmonitor(3) - Start monitor 4. stopmonitor(4) - Stop monitor 5. resumeport(5) - Resume port 6. invalid(-1) - Invalid value |
| INT hwBTSSTestedPortOperMode | 1.3.6.1.4.1.2011.6.21.3.1.1.18.1.2 | INTEGER | read-write | Operation mode of BTSS tested port. Options: 1. inline(1) - BTSS tested port in test 2. outline(2) - BTSS tested port out test 3. monitor(3) - Monitoring BTSS tested port 4. both(4) - Capture for circuit and loop-line test 5. meltNoCutxDSL(5) - Capture for melt chip test with co and cpe connecting 6. meltForceCutxDSL(6) - Capture for melt chip test with co and cpe disconnecting 7. testLineLoopback(7) - Capture for test line loopback 8. internalResistorLoopback(8) - Capture for internal resistor loopback 9. passthroughmode(9) - No capture Default: passthroughmode(9) |
| INT hwBTSSTestedPortOperResult | 1.3.6.1.4.1.2011.6.21.3.1.1.18.1.3 | INTEGER | accessible-for-notify | Test result of BTSS tested port. Options: 1. normal(1) - The test of BTSS tested port is successful 2. fail(2) - Fail in test of BTSS tested port 3. timeout(4) - The test of BTSS tested port is timeout |
| INT hwBTSSTestedPortTestBusyFlag | 1.3.6.1.4.1.2011.6.21.3.1.1.18.1.4 | INTEGER | read-write | Tested port force test. Options: 1. busyNoTest(1) - No test on busy 2. busyTest(2) - Test on busy 3. busystrenTest(3) - Forced test on busy |
| INT hwBTSSTestedPortTestPOTSFlag | 1.3.6.1.4.1.2011.6.21.3.1.1.18.1.5 | INTEGER | read-write | Tested port POTS service flag Options: 1. noCutPOTS(1) - No cut off POTS 2. busyNoTest(2) - No test on POTS busy (Cut off POTS) 3. busyTest(3) - Test on POTS busy (Cut off POTS) 4. busystrenTest(4) - Forced test on POTS busy (Cut off POTS) |
| hwBTSSCqtTransTestTable | 1.3.6.1.4.1.2011.6.21.3.1.1.19 | not-accessible | This table describes CQT test by transparent command. The index of this table is ifIndex. | |
| hwBTSSCqtTransTestEntry | 1.3.6.1.4.1.2011.6.21.3.1.1.19.1 | not-accessible | This table describes CQT test by transparent command. The index of this entry is ifIndex. | |
| INT hwBTSSCqtTransTestOperType | 1.3.6.1.4.1.2011.6.21.3.1.1.19.1.1 | INTEGER | read-write | CQT transparent Operation type Options: 1. stop(1) - Stop CQT transparent test 2. start(2) - Start CQT transparent test |
| INT hwBTSSCqtTransTestCRCMode | 1.3.6.1.4.1.2011.6.21.3.1.1.19.1.2 | INTEGER | read-write | CRC Operation type of CQT transparent. Options: 1. disable(1) - Disable CQT transparent 2. enable(2) - Enable CQT transparent Default: disable(1) |
| INT hwBTSSCqtTransTestOperResult | 1.3.6.1.4.1.2011.6.21.3.1.1.19.1.3 | INTEGER | accessible-for-notify | CQT transparent Operation result. Options: 1. normal(1) - The CQT transparent test is successful 2. fail(2) - The CQT transparent test fails 3. abort(3) - The CQT transparent test aborts 4. powerfeed(4) - The CQT transparent test power feeds |
| OCT hwBTSSCqtTransTestTxCmd | 1.3.6.1.4.1.2011.6.21.3.1.1.19.1.4 | OCTET STRING | read-write | Sending command string in TL1 format. |
| I32 hwBTSSCqtTransTestResultNo | 1.3.6.1.4.1.2011.6.21.3.1.1.19.1.5 | Integer32 | accessible-for-notify | Test result No. Range: 1-255 |
| INT hwBTSSCqtTransTestResultLastFlag | 1.3.6.1.4.1.2011.6.21.3.1.1.19.1.6 | INTEGER | accessible-for-notify | Last package flag for test result. Options: 1. false(0) - This is not the last package 2. true(1) - The last package |
| OCT hwBTSSCqtTransTestResult | 1.3.6.1.4.1.2011.6.21.3.1.1.19.1.7 | OCTET STRING | accessible-for-notify | CQT transparent Test result. |
| hwBTSSMultiFrameMiscOperTable | 1.3.6.1.4.1.2011.6.21.3.1.1.20 | not-accessible | This table describes test relatived operation for multi-frame. The index of this table is ifIndex. | |
| hwBTSSMultiFrameMiscOperEntry | 1.3.6.1.4.1.2011.6.21.3.1.1.20.1 | not-accessible | This table describes test relatived operation for multi-frame. The index of this entry is ifIndex. | |
| INT hwBTSSMultiFrameMiscCleanTest | 1.3.6.1.4.1.2011.6.21.3.1.1.20.1.1 | INTEGER | read-write | Clean current test on specified frame. Options: 1. start(1) - Start clean current test |
| I32 hwBTSSMultiFrameMiscTestedFrame | 1.3.6.1.4.1.2011.6.21.3.1.1.20.1.2 | Integer32 | read-write | Tested frame of BTSS multi-frame. Default: 0 |
| HWP hwBTSSMultiFrameMiscTestedPortType | 1.3.6.1.4.1.2011.6.21.3.1.1.20.1.3 | HWPortType | read-write | Tested port type of BTSS multi-frame. |
| HWB hwBTSSMultiFrameMiscTestedLineType | 1.3.6.1.4.1.2011.6.21.3.1.1.20.1.4 | HWBTSSxDslLineOverLap | read-write | Tested line type of BTSS multi-frame. |
| hwBTSSAdslSeltTestTable | 1.3.6.1.4.1.2011.6.21.3.1.1.21 | not-accessible | This table describes selt test for adsl2+. The index of this table is ifIndex. | |
| hwBTSSAdslSeltTestEntry | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1 | not-accessible | This table describes selt test for adsl2+. The index of this entry is ifIndex. | |
| INT hwBTSSAdslSeltTestOperType | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.1 | INTEGER | read-write | Selt test operation type. Options: 1. stop(1) - Stop selt test of BTSS 2. start(2) - Start selt test of BTSS 3. invalid(-1) - No operation |
| INT hwBTSSAdslSeltTestOperResult | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.2 | INTEGER | accessible-for-notify | Selt test operation result. Options: 1. normal(1) - Selt test of BTSS is successful 2. fail(2) - Fail in selt test of BTSS 3. abort(3) - Selt test of BTSS aborts |
| I32 hwBTSSAdslSeltTestResultNo | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.3 | Integer32 | accessible-for-notify | Selt test result serial number. Range: 1-255 |
| INT hwBTSSAdslSeltTestResultLastFlag | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.4 | INTEGER | accessible-for-notify | Last package flag of test. Options: 1. false(0) - This is not the last package 2. true(1) - The last package |
| OCT hwBTSSAdslSeltTestResult | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.5 | OCTET STRING | accessible-for-notify | Selt test result data. |
| I32 hwBTSSAdslSeltTestParamLoopLength | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.6 | Integer32 | read-only | Selt test parameter Loop Length. The invalid value is -1. If no SELT is performed, no SELT data is generated because the SELT is incomplete, or no SELT data can be obtained from the port because the SELT data is aged and cleared, the invalid value will be returned. |
| INT hwBTSSAdslSeltTestParamLoopTermin | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.7 | INTEGER | read-only | Selt test parameter Loop Termination state. Options: 1. open(0) - Indicates that the line terminal is started 2. short(1) - Indicates that the line terminal is short-circuited 3. unknow(2) - Indicates the unknown state 4. terminated(3) - Indicates that the line terminal is stopped 5. invalid(-1) - Indicates the invalid state |
| INT hwBTSSAdslSeltTestParamLoopGauge | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.8 | INTEGER | read-write | Selt test parameter Loop Gauge. Options: 1. greater26awg(1) - Indicates that the line gauge is greater than 26 2. equal26awg(2) - Indicates that the line gauge is 26 3. equal24awg(3) - Indicates that the line gauge is 24 4. less24awg(4) - Indicates that the line gauge is smaller than 24 5. unknowawg(5) - Indicates an unknown line gauge. 6. invalid(-1) - Indicates an invalid value. |
| I32 hwBTSSAdslSeltTestParamUpShnCap | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.9 | Integer32 | read-only | Selt test parameter Upstream Shannon Capacity. The invalid value is -1. If no SELT is performed, no SELT data is generated because the SELT is incomplete, or no SELT data can be obtained from the port because the SELT data is aged and cleared, the invalid value will be returned. |
| I32 hwBTSSAdslSeltTestParamDwnShnCap | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.10 | Integer32 | read-only | Selt test parameter Downstream Shannon Capacity. |
| OCT hwBTSSAdslSeltTestParamInbandNoise | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.11 | OCTET STRING | read-only | Selt test parameter Inband Noise 512 values that indicate inband noise in dBm/Hz, covering ADSL, ADSL2, and ADSL2+ bands, from 0 to 2.2 MHz. |
| OCT hwBTSSAdslSeltTestParamTerminResp | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.12 | OCTET STRING | read-only | Selt test parameter Termination Response 180 values that indicate termination response magnitude from 0 to 18 kft. |
| OCT hwBTSSAdslSeltTestParamUpMgnAtRate | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.13 | OCTET STRING | read-only | Selt test parameter Upstream Ratevs. Margin. This value is a measure of the quality of your upstream data signal relative to the noise on the line. Hundreds of values that indicate SNR margin in DB/Hz at a particular bit rate are provided, at a certain increments, up to 30 Mbps. This information may be plotted with the bit rate on the X-axis and the SNR margin on the Y-axis. |
| OCT hwBTSSAdslSeltTestParamDwnMgnAtRate | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.14 | OCTET STRING | read-only | Selt test parameter Downstream Rate vs. Margin. This value is a measure of the quality of your downstream data signal relative to the noise on the line. Hundreds of values that indicate SNR margin in DB/Hz at a particular bit rate are provided, at a certain increments, up to 30 Mbps. This information may be plotted with the bit rate on the X-axis and the SNR margin on the Y-axis. |
| OCT hwBTSSAdslSeltTestParamUpRateAtMgn | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.15 | OCTET STRING | read-only | Selt test parameter Upstream Margin vs. Rate. |
| OCT hwBTSSAdslSeltTestParamDwnRateAtMgn | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.16 | OCTET STRING | read-only | Selt test parameter Downstream Margin vs. Rate. |
| OCT hwBTSSAdslSeltTestParamLoopAttenAtFreq | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.17 | OCTET STRING | read-only | Selt test parameter loop attenuation versus frequency. Every four bytes constitute the result of a tone. This information may be plotted with the bit frequency on the X-axis and the loop attenuation on the Y-axis. |
| U32 hwBTSSAdslSeltTestParamUnCalibLineScale | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.18 | Unsigned32 | read-only | The uncalibrated echo response, UER(i* UER_G*Df), shall be represented in linear format by a scale factor and a normalized complex number a(i)+j*b(i), where i is a frequency index i ranging from 0 to NSC-1, the subcarrier spacing, Df = 4.3125 kHz, and (NSC-1) * UER_G * Df is the highest frequency supported by the SELT-PMD functionality. The UER granularity parameter, UER_G, has two valid values: 1 and 2, indicating whether the measurements were performed using a tone spacing of 4.3125 kHz or of 8.625 kHz. If the uncalibrated echo response is being reported over a frequency range of 17.664 MHz or lower, UER_G shall be set to 1. If the uncalibrated echo response is being reported over a frequency range that is greater than 17.664 MHz, UER_G shall be set to 2. The scale factor shall be coded as a 32-bit unsigned integer. Both a(i) and b(i) shall be coded as 32-bit 2's complement signed integers. The value of UER(i* UER_G*Df) shall be defined as: UER(i* UER_G*Df) = (scale/2^31)*(a(i)+j*b(i))/2^31. In order to maximize precision, the scale factor shall be chosen such that max(|a(i)|, |b(i)|) over all i is equal to 2^31-1. NOTE - This data format supports an UER(f) granularity of 2^-31 and an UER(f) dynamic range of approximately +6 dB to -186 dB, however it does not imply any future accuracy requirements. An UER(i*UER_G* Df) value indicated as a(i) = b(i) = -2^31 is a special value. It indicates that no measurement could be done for this subcarrier either because it is not supported by the SELT-PMD function, or that the value is out of range to be represented. |
| OCT hwBTSSAdslSeltTestParamUnCalibEchoRespReal | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.19 | OCTET STRING | read-only | The uncalibrated echo response, UER(i* UER_G*Df), shall be represented in linear format by a scale factor and a normalized complex number a(i)+j*b(i), where i is a frequency index i ranging from 0 to NSC-1, the subcarrier spacing, Df = 4.3125 kHz, and (NSC-1) * UER_G * Df is the highest frequency supported by the SELT-PMD functionality. The UER granularity parameter, UER_G, has two valid values: 1 and 2, indicating whether the measurements were performed using a tone spacing of 4.3125 kHz or of 8.625 kHz. If the uncalibrated echo response is being reported over a frequency range of 17.664 MHz or lower, UER_G shall be set to 1. If the uncalibrated echo response is being reported over a frequency range that is greater than 17.664 MHz, UER_G shall be set to 2. The scale factor shall be coded as a 32-bit unsigned integer. Both a(i) and b(i) shall be coded as 32-bit 2's complement signed integers. The value of UER(i* UER_G*Df) shall be defined as: UER(i* UER_G*Df) = (scale/2^31)*(a(i)+j*b(i))/2^31. In order to maximize precision, the scale factor shall be chosen such that max(|a(i)|, |b(i)|) over all i is equal to 2^31-1. NOTE - This data format supports an UER(f) granularity of 2^-31 and an UER(f) dynamic range of approximately +6 dB to -186 dB, however it does not imply any future accuracy requirements. An UER(i*UER_G* Df) value indicated as a(i) = b(i) = -2^31 is a special value. It indicates that no measurement could be done for this subcarrier either because it is not supported by the SELT-PMD function, or that the value is out of range to be represented. |
| OCT hwBTSSAdslSeltTestParamUnCalibEchoRespImg | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.20 | OCTET STRING | read-only | The uncalibrated echo response, UER(i* UER_G*Df), shall be represented in linear format by a scale factor and a normalized complex number a(i)+j*b(i), where i is a frequency index i ranging from 0 to NSC-1, the subcarrier spacing, Df = 4.3125 kHz, and (NSC-1) * UER_G * Df is the highest frequency supported by the SELT-PMD functionality. The UER granularity parameter, UER_G, has two valid values: 1 and 2, indicating whether the measurements were performed using a tone spacing of 4.3125 kHz or of 8.625 kHz. If the uncalibrated echo response is being reported over a frequency range of 17.664 MHz or lower, UER_G shall be set to 1. If the uncalibrated echo response is being reported over a frequency range that is greater than 17.664 MHz, UER_G shall be set to 2. The scale factor shall be coded as a 32-bit unsigned integer. Both a(i) and b(i) shall be coded as 32-bit 2's complement signed integers. The value of UER(i* UER_G*Df) shall be defined as: UER(i* UER_G*Df) = (scale/2^31)*(a(i)+j*b(i))/2^31. In order to maximize precision, the scale factor shall be chosen such that max(|a(i)|, |b(i)|) over all i is equal to 2^31-1. NOTE - This data format supports an UER(f) granularity of 2^-31 and an UER(f) dynamic range of approximately +6 dB to -186 dB, however it does not imply any future accuracy requirements. An UER(i*UER_G* Df) value indicated as a(i) = b(i) = -2^31 is a special value. It indicates that no measurement could be done for this subcarrier either because it is not supported by the SELT-PMD function, or that the value is out of range to be represented. |
| U32 hwBTSSAdslSeltTestParamCalibLineScale | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.21 | Unsigned32 | read-only | The scale factor of calibrated echo response shall be coded as a 16 bit unsigned integer. |
| OCT hwBTSSAdslSeltTestParamCalibEchoRespReal | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.22 | OCTET STRING | read-only | The calibrated echo response UER(i* f), shall be represented in linear format by a scale factor and a normalized complex number a(i)+j*b(i), where i is the subcarrier index i ranging from 0 to NSC-1 and Df = 4.3125kHz and (NSC-1) * Df is the highest frequency supported by the SELT-PMD functionality. The scale factor shall be coded as a 16 bit unsigned integer. Both a(i) and b(i) shall be coded as a 16 bit 2's complement signed integer. The value of UER(i* f) shall be defined as UER(i* f) = (scale/215)*(a(i)+j*b(i))/215. In order to maximize precision, the scale factor shall be chosen such that max(|a(i)|, |b(i)|) over all i is equal to 215-1. This data format supports an UER(f) granularity of 2-15 and an UER(f) dynamic range of approximately +6 dB to -90 dB. An UER(i*Df) value indicated as a(i) = b(i) = -215 is a special value. It indicates that no measurement could be done for this subcarrier because it is out of the PSD mask passband or that the value is out of range to be represented. |
| OCT hwBTSSAdslSeltTestParamCalibEchoRespImg | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.23 | OCTET STRING | read-only | The calibrated echo response UER(i* f), shall be represented in linear format by a scale factor and a normalized complex number a(i)+j*b(i), where i is the subcarrier index i ranging from 0 to NSC-1 and Df = 4.3125kHz and (NSC-1) * Df is the highest frequency supported by the SELT-PMD functionality. The scale factor shall be coded as a 16 bit unsigned integer. Both a(i) and b(i) shall be coded as a 16 bit 2's complement signed integer. The value of UER(i* f) shall be defined as UER(i* f) = (scale/215)*(a(i)+j*b(i))/215. In order to maximize precision, the scale factor shall be chosen such that max(|a(i)|, |b(i)|) over all i is equal to 215-1. This data format supports an UER(f) granularity of 2-15 and an UER(f) dynamic range of approximately +6 dB to -90 dB. An UER(i*Df) value indicated as a(i) = b(i) = -215 is a special value. It indicates that no measurement could be done for this subcarrier because it is out of the PSD mask passband or that the value is out of range to be represented. |
| OCT hwBTSSAdslSeltTestParamVarUerC | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.24 | OCTET STRING | read-only | The relative variance of the uncalibrated echo response REL_VAR_UER(i* UER_G *Df) shall be represented as an 8-bit unsigned integer v(i), where i is the subcarrier index i = 0 to NSC-1. The value of REL_VAR_UER(i* UER_G *Df) shall be defined as REL_VAR_UER(i* UER_G *Df) = 3 - v(i)/2 dB. The number v(i) is an 8-bit unsigned integer in the range 0 to 254. This data format supports a REL_VAR_UER(i) over a range from -124 dB to +3 dB for each carrier with a granularity from 0.5 dB. Out of range values shall be clamped to the closest range bound. The special value v(i) = 255 indicates that no measurement is available for that carrier. Unit: 0.5dB |
| U32 hwBTSSAdslSeltTestParamUerMmdC | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.25 | Unsigned32 | read-write | This parameter is the maximum allowed time for SELT uncalibrated echo response measurement, between the time of the start command written by the SELT-PMD-ME, and the time the result is available for read operation by SELT-PMD-ME. It is configurable between 5 seconds and 240 seconds, in steps of 1 second. The invalid value is 255. If data on the port cannot be queried, the invalid value will be returned. Unit: 1 second |
| U32 hwBTSSAdslSeltTestParamQlnMmdC | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.26 | Unsigned32 | read-write | This parameter is the maximum allowed time for SELT quiet line noise measurement, between the time of the start command written by the SELT-PMD-ME, and the time the result is available for read operation by SELT-PMD-ME. It is configurable between 1 second and 240 seconds, in steps of 1 second. The invalid value is 255. If data on the port cannot be queried, the invalid value will be returned. Unit: 1 second |
| INT hwBTSSAdslSeltTestParamUmeC | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.27 | INTEGER | read-write | This parameter is a binary variable. Options: 1.enable(1) - Enable UER capture switch 2.disable(2) - Disable UER capture switch 3.invalid(-1) - Invalid value |
| INT hwBTSSAdslSeltTestParamQmeC | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.28 | INTEGER | read-write | This parameter is a binary variable. Options: 1.enable(1) - Enable QLN capture switch 2.disable(2) - Disable QLN capture switch 3.invalid(-1) - Invalid value |
| INT hwBTSSAdslSeltTestParamUerStatus | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.29 | INTEGER | read-only | UerStatus. Options: 1.off(1) - The status is off. 2.running(2) - The status is running. 3.completed(3) - The status is completed. 4.failed(4) - The status is failed. |
| INT hwBTSSAdslSeltTestParamQlnStatus | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.30 | INTEGER | read-only | QlnStatus. Options: 1.off(1) - The status is off. 2.running(2) - The status is running. 3.completed(3) - The status is completed. 4.failed(4) - The status is failed. |
| INT hwBTSSAdslSeltTestParamCalcEnable | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.31 | INTEGER | read-write | The status of calculation switch. Options: 1. enable(1) - Enable calculation switch 2. disable(2) - Disable calculation switch 3. invalid(-1) - Invalid value Default: enable(1) |
| I32 hwBTSSAdslSeltTestParamAttnAt180KHZ | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.65535 | Integer32 | read-only | Selt test parameter attenuation at 180KHZ. It ranges from -1100 to 0 units of 0.1dB(physical values are -110 to 0 dB). The invalid value is -1. If no SELT is performed, no SELT data is generated because the SELT is incomplete, or no SELT data can be obtained from the port because the SELT data is aged and cleared, the invalid value will be returned. Unit: 0.1dB |
| I32 hwBTSSAdslSeltTestParamAttnAt300KHZ | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.65536 | Integer32 | read-only | Selt test parameter attenuation at 300KHZ. It ranges from -1100 to 0 units of 0.1dB(physical values are -110 to 0 dB). The invalid value is -1. If no SELT is performed, no SELT data is generated because the SELT is incomplete, or no SELT data can be obtained from the port because the SELT data is aged and cleared, the invalid value will be returned. Unit: 0.1dB |
| OCT hwBTSSAdslSeltTestParamQSPsdValue | 1.3.6.1.4.1.2011.6.21.3.1.1.21.1.65537 | OCTET STRING | read-only | The SELT quiet line noise provides the quiet line noise PSD as measured by the SELT-PMD function (see clause A.1.1.2) for each sub-carrier frequency i * SELTQLN_G * Df where i ranges from 0 to NSC-1, Df = 4.3125 kHz, and (NSC-1) * SELTQLN_G * Df is the highest frequency supported by the SELT-PMD functionality. SELTQLN_G has two valid values: 1 and 2, indicating whether the measurements were performed using a tone spacing of 4.3125 kHz or of 8.625 kHz. If the SELT quiet line noise is being reported over a frequency range of 17.664 MHz or lower, SELTQLN_G shall be set to 1. If the SELT quiet line noise is being reported over a frequency range that is greater than 17.664 MHz, SELTQLN_G shall be set to 2. SELT quiet line noise SELTQLN(i * SELTQLN_G * Df) shall be represented as an 8-bit unsigned integer n(i), where i is the subcarrier index i = 0 to NSC-1. The value of SELTQLN(i * SELTQLN_G * Df) shall be defined as SELTQLN(i * SELTQLN_G * Df ) = -23 - (n(i)/2) dBm/Hz. This data format supports a SELTQLN(f) granularity of 0.5 dB and an SELTQLN(f) dynamic range of -150 to -23 dBm/Hz. Unit: 0.5dBm/Hz |
| hwBTSSAdslDeltTestTable | 1.3.6.1.4.1.2011.6.21.3.1.1.22 | not-accessible | This table describes Delt test for adsl2+. The index of this table is ifIndex. | |
| hwBTSSAdslDeltTestEntry | 1.3.6.1.4.1.2011.6.21.3.1.1.22.1 | not-accessible | This table describes Delt test for adsl2+. The index of this entry is ifIndex. | |
| INT hwBTSSAdslDeltTestOperType | 1.3.6.1.4.1.2011.6.21.3.1.1.22.1.1 | INTEGER | read-write | Delt test operation type. Options: 1. stop(1) - Delt test stop 2. start(2) - Start delt test 3. invalid(-1) - No operation |
| INT hwBTSSAdslDeltTestOperResult | 1.3.6.1.4.1.2011.6.21.3.1.1.22.1.2 | INTEGER | accessible-for-notify | Delt test operation result. Options: 1. normal(1) - Delt test is normal 2. fail(2) - Fail in delt test 3. abort(3) - Delt test aborts |
| I32 hwBTSSAdslDeltTestResultNo | 1.3.6.1.4.1.2011.6.21.3.1.1.22.1.3 | Integer32 | accessible-for-notify | Delt test result serial number. Range: 1-255 |
| INT hwBTSSAdslDeltTestResultLastFlag | 1.3.6.1.4.1.2011.6.21.3.1.1.22.1.4 | INTEGER | accessible-for-notify | Last package flag for test result. Options: 1. false(0) - This is not the last package 2. true(1) - The last package |
| OCT hwBTSSAdslDeltTestResult | 1.3.6.1.4.1.2011.6.21.3.1.1.22.1.5 | OCTET STRING | accessible-for-notify | Delt test result data. |
| hwBTSSLoopLineToneOprTable | 1.3.6.1.4.1.2011.6.21.3.1.1.23 | not-accessible | The table hwBTSSLoopLineToneOprTable is used to Loop Line Tone. The index of this table is ifIndex. | |
| hwBTSSLoopLineToneOprEntry | 1.3.6.1.4.1.2011.6.21.3.1.1.23.1 | not-accessible | The table hwBTSSLoopLineToneOprTable is used to Loop Line Tone. The index of this entry is ifIndex. | |
| INT hwBTSSLoopLineToneOprType | 1.3.6.1.4.1.2011.6.21.3.1.1.23.1.1 | INTEGER | read-write | Operation type of BTSS loop line tone Options: 1. check(1) - Indicates that checking the signal tone is started 2. send(2) - Indicates that sending the signal tone is started 3. stopsend(3) - Indicates that stopping sending the signal tone is started |
| INT hwBTSSLoopLineToneIntensity | 1.3.6.1.4.1.2011.6.21.3.1.1.23.1.2 | INTEGER | read-write | Tone intensity of BTSS loop line tone. Options: 1. fivedB(1) - Tone intensity of BTSS is five dB 2. tendB(2) - Tone intensity of BTSS is ten dB 3. fifteendB(3) - Tone intensity of BTSS is fifteen dB |
| INT hwBTSSLoopLineToneBusyFlag | 1.3.6.1.4.1.2011.6.21.3.1.1.23.1.3 | INTEGER | read-write | Tested port force test of BTSS loop line tone. Options: 1. busyNoTest(1) - No test on busy 2. busyTest(2) - Test on busy 3. busystrenTest(3) - Forced test on busy |
| INT hwBTSSLoopLineToneResult | 1.3.6.1.4.1.2011.6.21.3.1.1.23.1.4 | INTEGER | read-only | Operate result of BTSS loop line tone. Options: 1. succeed(1) - The test of BTSS loop line tone is successful 2. failed(2) - Failed in BTSS loop line tone test |
| hwBTSSSeltAuxPortCfgTable | 1.3.6.1.4.1.2011.6.21.3.1.1.24 | not-accessible | This table sets assistance port for SELT. The index of this table is hwBTSSSeltAuxedPortIfIndex. | |
| hwBTSSSeltAuxPortCfgEntry | 1.3.6.1.4.1.2011.6.21.3.1.1.24.1 | not-accessible | This table sets assistance port for SELT. The index of this entry is hwBTSSSeltAuxedPortIfIndex. | |
| I32 hwBTSSSeltAuxedPortIfIndex | 1.3.6.1.4.1.2011.6.21.3.1.1.24.1.1 | Integer32 | not-accessible | The ifindex of the Auxed port. If there is only one global Auxed port, the value is 65535. |
| I32 hwBTSSSeltAuxPortIfIndex | 1.3.6.1.4.1.2011.6.21.3.1.1.24.1.2 | Integer32 | read-write | Assistance port ifIndex |
| ROW hwBTSSSeltAuxPortRowStatus | 1.3.6.1.4.1.2011.6.21.3.1.1.24.1.3 | RowStatus | read-create | Row status(add(4), delete(6)) of the Aux port. |
| hwBTSSAdslSeltLevelTable | 1.3.6.1.4.1.2011.6.21.3.1.1.25 | not-accessible | This table supports the configuration of adsl selt level. The indexes of this table are hwFrameIndex and hwSlotIndex. | |
| hwBTSSAdslSeltLevelEntry | 1.3.6.1.4.1.2011.6.21.3.1.1.25.1 | not-accessible | This table supports the configuration of adsl selt level. The indexes of this entry are hwFrameIndex and hwSlotIndex. | |
| I32 hwBTSSAdslSeltLevel | 1.3.6.1.4.1.2011.6.21.3.1.1.25.1.1 | Integer32 | read-write | The level of adsl SELT: 1 Level0; 2 Level1; 3 Level2; 4 Level3. A special value of -1 indicates the level of adsl SELT is invalid. |
| hwBTSSAdslSeltCalibrationTable | 1.3.6.1.4.1.2011.6.21.3.1.1.26 | not-accessible | This table describes calibration data of selt test. The index of this table is ifIndex. | |
| hwBTSSAdslSeltCalibrationEntry | 1.3.6.1.4.1.2011.6.21.3.1.1.26.1 | not-accessible | This table describes calibration data of selt test. The index of this entry is ifIndex. | |
| OCT hwBTSSAdslSeltCalibrationInvVendorId | 1.3.6.1.4.1.2011.6.21.3.1.1.26.1.1 | OCTET STRING | read-only | It consists of 8 binary octets, including a provider code. |
| OCT hwBTSSAdslSeltCalibrationDataSegment1 | 1.3.6.1.4.1.2011.6.21.3.1.1.26.1.2 | OCTET STRING | read-only | The part 1 of selt calibration data. The unit of selt calibration data is 0.00001. |
| OCT hwBTSSAdslSeltCalibrationDataSegment2 | 1.3.6.1.4.1.2011.6.21.3.1.1.26.1.3 | OCTET STRING | read-only | The part 2 of selt calibration data. The unit of selt calibration data is 0.00001. |
| hwBTestTraps | 1.3.6.1.4.1.2011.6.21.3.2 | |||
| hwBTestTrapVbOids | 1.3.6.1.4.1.2011.6.21.3.2.1 | |||
| hwBTestVbOidsReason | 1.3.6.1.4.1.2011.6.21.3.2.1.2 | |||
| INT hwBTSSCqtOfflineReason | 1.3.6.1.4.1.2011.6.21.3.2.1.2.1 | INTEGER | accessible-for-notify | Cqt module offline reason. Options: 1. commFail(1) - CQT module communication fail. Resolving method:Check CQT module running normal 2. userReset(2) - User reset command |
| I32 hwBTSSRequestID | 1.3.6.1.4.1.2011.6.21.3.2.1.2.2 | Integer32 | accessible-for-notify | NMS request ID. |
| hwBTestAlarmTraps | 1.3.6.1.4.1.2011.6.21.3.2.2 | |||
| hwBTestAlarmTrapsOIDs | 1.3.6.1.4.1.2011.6.21.3.2.2.0 | |||
| NTF hwBTSSCqtOnlineTrap | 1.3.6.1.4.1.2011.6.21.3.2.2.0.1 | CQT unit online status trap. This notification indicates alarm when CQT unit online. enumFirst: explain: CQT module communication OK resolving method:NA. | ||
| NTF hwBTSSCqtOfflineTrap | 1.3.6.1.4.1.2011.6.21.3.2.2.0.2 | CQT unit offline status trap. This notification indicates alarm when CQT unit offline. | ||
| hwBTestGeneralTraps | 1.3.6.1.4.1.2011.6.21.3.2.3 | |||
| hwBTestGeneralTrapsOIDs | 1.3.6.1.4.1.2011.6.21.3.2.3.0 | |||
| NTF hwBTSSCoStartTrap | 1.3.6.1.4.1.2011.6.21.3.2.3.0.1 | Start Co test trap. This notification indicates alarm when starting Co test. | ||
| NTF hwBTSSCoStopTrap | 1.3.6.1.4.1.2011.6.21.3.2.3.0.2 | Stop Co test trap. This notification indicates alarm when stopping Co test. | ||
| NTF hwBTSSTestedPortOperTrap | 1.3.6.1.4.1.2011.6.21.3.2.3.0.3 | Tested port operation trap. This notification indicates alarm when tested port operation. | ||
| NTF hwBTSSCqtTransTestOperResultTrap | 1.3.6.1.4.1.2011.6.21.3.2.3.0.4 | Cqt transparent test trap. This notification indicates alarm when starting or stoping Cqt transparent test. | ||
| NTF hwBTSSCqtTransTestResultTrap | 1.3.6.1.4.1.2011.6.21.3.2.3.0.5 | Cqt transparent test trap. This notification indicates alarm when reporting the result after Cqt transparent test. | ||
| NTF hwBTSSLoopLineToneOperTrap | 1.3.6.1.4.1.2011.6.21.3.2.3.0.6 | loop line tone test result trap: 1:hwBTSSLoopLineToneResult. This notification indicates alarm when reporting the test result of Loop Line Tone. | ||
| NTF hwBTSSCaptureTrap | 1.3.6.1.4.1.2011.6.21.3.2.3.0.7 | BTSS capture trap. This trap is sent when BTSS capture result reported. | ||
| NTF hwBTSSDeltResultDataTrap | 1.3.6.1.4.1.2011.6.21.3.2.3.0.8 | BTSS delt result trap. This notification indicates alarm when captures result data of BTSS delt test. |
RFC description
Broad test management MIB for Huawei ADSL and network device testing.
Start monitoring Huawei broadband access platform (DSLAM/MSAN, xDSL line diagnostics) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.