HPN-ICF-TRAP-MIB

All MIBs › HPN-ICF-TRAP-MIB

Last Updated: 2010-06-05

Category: Alarm and Event Management, SNMP Framework, Vendor: H3C/HH3C, Vendor: HP/HPE

Description: Defines enterprise-specific SNMP trap notifications for system and network events on HP/Comware devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HPN-ICF-TRAP-MIB?

HPN-ICF-TRAP-MIB is an HP/H3C Comware enterprise MIB that defines the SNMP trap (notification) types generated by routers, switches, and related network products in that product family. Rather than exposing polled counters or tables, it standardizes the format and variable bindings of alert messages the device sends when significant system or network events occur. It is used specifically to monitor the health and status of the device by surfacing asynchronous fault and state-change events, such as hardware failures, interface state transitions, configuration changes, or security-related occurrences, that operators would otherwise have to detect by polling. Because it is a trap-only module, it typically depends on lower-layer notification infrastructure such as SNMPv2-TM and RFC 3411 framework MIBs for delivery. It is deployed on HP/H3C Comware-based routers and switches, where HPN-ICF-TRAP-MIB SNMP monitoring configures a network management system to receive and correlate these traps for real-time alerting.

IPNetwork Monitor allows you to monitor SNMP objects defined in HPN-ICF-TRAP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

HP/H3C Comware routers
HP/H3C Comware switches

Monitoring Examples

As a trap-definitions module, HPN-ICF-TRAP-MIB has no runtime data tables or counters of its own to poll; instead an NMS registers as a trap receiver and reacts when the device emits one of the enterprise-specific notifications defined here. A realistic scenario is the NMS logging a trap indicating a hardware or interface fault on the chassis and triggering an alert workflow rather than discovering the issue via periodic polling. Because the module description notes objects may be product-specific, the exact set of traps that fire depends on the particular Comware hardware model in use.

Imported Objects

From HPN-ICF-OID-MIB

hpnicfCommon

OBJECT-IDENTITY

From IF-MIB

InterfaceIndex
ifDescr	OBJECT-TYPE
ifIndex	OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

RowStatus
TAddress
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
hpnicfTrap	1.3.6.1.4.1.11.2.14.11.15.2.38			This MIB is applicable to routers, switches and other products. Some objects in this may be used only for some specific products, so users should refer to the related documents to acquire more detail information.
hpnicfTableGroup	1.3.6.1.4.1.11.2.14.11.15.2.38.1
hpnicfMacTabStatGroup	1.3.6.1.4.1.11.2.14.11.15.2.38.1.1
INT hpnicfMacTabTrapEnable	1.3.6.1.4.1.11.2.14.11.15.2.38.1.1.1	INTEGER	read-write	Indicates whether hpnicfMacTabFullTrap and hpnicfMacTabAlmostFullTrap traps should be generated when the MAC table is filled.
I32 hpnicfMacTabTrapInterval	1.3.6.1.4.1.11.2.14.11.15.2.38.1.1.2	Integer32	read-write	Definition of the minimum interval between two traps which occur when the MAC table is full or two traps which occur when the MAC table is almost full.
hpnicfMacTabTrapInfo	1.3.6.1.4.1.11.2.14.11.15.2.38.1.1.3
I32 hpnicfMacTabLen	1.3.6.1.4.1.11.2.14.11.15.2.38.1.1.3.1	Integer32	accessible-for-notify	The length of the MAC table.
hpnicfMacTabTrap	1.3.6.1.4.1.11.2.14.11.15.2.38.1.1.4
NTF hpnicfMacTabFullTrap	1.3.6.1.4.1.11.2.14.11.15.2.38.1.1.4.1			Send this trap when the MAC table is filled. The interval between two traps generated should be longer than hpnicfMacTabTrapInterval.
NTF hpnicfMacTabAlmostFullTrap	1.3.6.1.4.1.11.2.14.11.15.2.38.1.1.4.2			Send this trap when the MAC table is almost full. The interval between two traps generated should be longer than hpnicfMacTabTrapInterval.
hpnicfArpTabStatGroup	1.3.6.1.4.1.11.2.14.11.15.2.38.1.2
INT hpnicfArpTabTrapEnable	1.3.6.1.4.1.11.2.14.11.15.2.38.1.2.1	INTEGER	read-write	Indicates whether hpnicfArpTabFullTrap traps should be generated when the ARP table is filled.
I32 hpnicfArpTabTrapInterval	1.3.6.1.4.1.11.2.14.11.15.2.38.1.2.2	Integer32	read-write	Definition of the minimum interval between two traps which occur when the ARP table is filled.
hpnicfArpTabTrapInfo	1.3.6.1.4.1.11.2.14.11.15.2.38.1.2.3
I32 hpnicfArpTabLen	1.3.6.1.4.1.11.2.14.11.15.2.38.1.2.3.1	Integer32	accessible-for-notify	The length of the ARP table.
hpnicfArpTabTrap	1.3.6.1.4.1.11.2.14.11.15.2.38.1.2.4
NTF hpnicfArpTabFullTrap	1.3.6.1.4.1.11.2.14.11.15.2.38.1.2.4.1			Send this trap when the ARP table is filled. The interval between two traps generated should be longer than hpnicfArpTabTrapInterval.
NTF hpnicfArpPortDynamicEntryFullTrap	1.3.6.1.4.1.11.2.14.11.15.2.38.1.2.4.2			Send this trap when the dynamic ARP number of the port exceeds the limitation. The object hpnicfArpTabLen describes the limitation of the max dynamic ARP number of this port. The interval between two traps should be longer than hpnicfArpTabTrapInterval.
hpnicfRtTabStatGroup	1.3.6.1.4.1.11.2.14.11.15.2.38.1.3
hpnicfDetailRtTrapTable	1.3.6.1.4.1.11.2.14.11.15.2.38.1.3.1		not-accessible	This table contains objects to decide what kind of trap should be sent.
hpnicfDetailRtTrapEntry	1.3.6.1.4.1.11.2.14.11.15.2.38.1.3.1.1		not-accessible	Entry items
INT hpnicfDetailRtProType	1.3.6.1.4.1.11.2.14.11.15.2.38.1.3.1.1.1	INTEGER	accessible-for-notify	The index value which uniquely identifies an entry in the hpnicfDetailRtTrapTable.
INT hpnicfDetailRtEnable	1.3.6.1.4.1.11.2.14.11.15.2.38.1.3.1.1.2	INTEGER	read-write	Indicates whether hpnicfDetailRtTabFullTrap traps should be generated when a specific routing table is filled.
INT hpnicfRtTabTrapEnable	1.3.6.1.4.1.11.2.14.11.15.2.38.1.3.2	INTEGER	read-write	Indicates whether hpnicfRtTabFullTrap traps should be generated when the routing table is filled.
I32 hpnicfRtTabTrapInterval	1.3.6.1.4.1.11.2.14.11.15.2.38.1.3.3	Integer32	read-write	Definition of the minimum interval between two traps which occur when the routing table is filled.
hpnicfRtTabTrapInfo	1.3.6.1.4.1.11.2.14.11.15.2.38.1.3.4
I32 hpnicfRtTabLen	1.3.6.1.4.1.11.2.14.11.15.2.38.1.3.4.1	Integer32	accessible-for-notify	The length of the routing table. The detail routing tables also use the same object.
IPt hpnicfDefaultRtNextHopType	1.3.6.1.4.1.11.2.14.11.15.2.38.1.3.4.2	InetAddressType	accessible-for-notify	The IP address type of the next hop of the default route. The value must be ipv4 or ipv6
IP hpnicfDefaultRtNextHop	1.3.6.1.4.1.11.2.14.11.15.2.38.1.3.4.3	InetAddress	accessible-for-notify	The IP address of the next hop of the default route.
NUM hpnicfDefaultRtOutIf	1.3.6.1.4.1.11.2.14.11.15.2.38.1.3.4.4	InterfaceIndex	accessible-for-notify	The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
hpnicfRtTabTrap	1.3.6.1.4.1.11.2.14.11.15.2.38.1.3.5
NTF hpnicfRtTabFullTrap	1.3.6.1.4.1.11.2.14.11.15.2.38.1.3.5.1			Send this trap when the routing table is filled. The interval between two traps generated should be longer than hpnicfRtTabTrapInterval.
NTF hpnicfDetailRtTabFullTrap	1.3.6.1.4.1.11.2.14.11.15.2.38.1.3.5.2			Send this trap when the detail routing table is filled. The interval between two traps generated should be longer than hpnicfRtTabTrapInterval.
NTF hpnicfDefaultRtDelTrap	1.3.6.1.4.1.11.2.14.11.15.2.38.1.3.5.3			Send this trap when the default route is deleted.
T/F hpnicfDefaultRtDelTrapEnable	1.3.6.1.4.1.11.2.14.11.15.2.38.1.3.6	TruthValue	read-write	Indicates whether hpnicfDefaultRtDelTrap traps should be generated when the default route is deleted.
hpnicfMulticastTabStatGroup	1.3.6.1.4.1.11.2.14.11.15.2.38.1.4
INT hpnicfMulticastTabTrapEnable	1.3.6.1.4.1.11.2.14.11.15.2.38.1.4.1	INTEGER	read-write	Indicates whether hpnicfMulticastTabFullTrap traps should be generated when the multicast table is filled.
I32 hpnicfMulticastTabTrapInterval	1.3.6.1.4.1.11.2.14.11.15.2.38.1.4.2	Integer32	read-write	Definition of the minimum interval between two traps which occur when the multicast table is filled.
hpnicfMulticastTabTrapInfo	1.3.6.1.4.1.11.2.14.11.15.2.38.1.4.3
INT hpnicfMulticastTabType	1.3.6.1.4.1.11.2.14.11.15.2.38.1.4.3.1	INTEGER	accessible-for-notify	Defining the type of the multicast table, layer2 or layer3.
I32 hpnicfMulticastTabLen	1.3.6.1.4.1.11.2.14.11.15.2.38.1.4.3.2	Integer32	accessible-for-notify	The length of the multicast table.
hpnicfMulticastTabTrap	1.3.6.1.4.1.11.2.14.11.15.2.38.1.4.4
NTF hpnicfMulticastTabFullTrap	1.3.6.1.4.1.11.2.14.11.15.2.38.1.4.4.1			Send this trap when the multicast table is filled. The interval between two traps generated should be longer than hpnicfMulticastTabTrapInterval.
hpnicfNdTabStatGroup	1.3.6.1.4.1.11.2.14.11.15.2.38.1.5
INT hpnicfNdTabTrapEnable	1.3.6.1.4.1.11.2.14.11.15.2.38.1.5.1	INTEGER	read-write	Indicates whether hpnicfNdTabFullTrap traps should be generated when the ND table is filled.
I32 hpnicfNdTabTrapInterval	1.3.6.1.4.1.11.2.14.11.15.2.38.1.5.2	Integer32	read-write	Definition of the minimum interval between two traps which occur when the ND table is filled.
hpnicfNdTabTrapInfo	1.3.6.1.4.1.11.2.14.11.15.2.38.1.5.3
I32 hpnicfNdTabLen	1.3.6.1.4.1.11.2.14.11.15.2.38.1.5.3.1	Integer32	accessible-for-notify	The length of the ND table.
hpnicfNdTabTrap	1.3.6.1.4.1.11.2.14.11.15.2.38.1.5.4
NTF hpnicfNdTabFullTrap	1.3.6.1.4.1.11.2.14.11.15.2.38.1.5.4.1			Send this trap when the ND table is filled. The interval between two traps generated should be longer than hpnicfNdTabTrapInterval.
hpnicfPeriodicalTrapGroup	1.3.6.1.4.1.11.2.14.11.15.2.38.1.6
hpnicfPeriodicalTrapObjects	1.3.6.1.4.1.11.2.14.11.15.2.38.1.6.1
I32 hpnicfPeriodicalTrapInterval	1.3.6.1.4.1.11.2.14.11.15.2.38.1.6.1.1	Integer32	read-write	Definition of the periodical interval. If no trap occurs during the certain interval, an hpnicfPeriodicalTrap will be generated. If the interval is set to 0, no hpnicfPeriodicalTrap will be generated.
INT hpnicfPeriodicalTrapSwitch	1.3.6.1.4.1.11.2.14.11.15.2.38.1.6.1.2	INTEGER	read-write	Definition of the periodical switch. If the value is off,the hpnicfPeriodicalTrap will not be generated. the hpnicfPeriodicalTrapInterval will be set to 0.
INT hpnicfPeriodicalTrapSwitch2	1.3.6.1.4.1.11.2.14.11.15.2.38.1.6.1.3	INTEGER	read-write	Periodical heartbeat trap sending switch. If the value is off, the hpnicfPeriodicalTrap will not be generated, and the hpnicfPeriodicalTrapInterval will be set to 0. This node differs from hpnicfPeriodicalTrapSwitch in value.
hpnicfPeriodicalTrapInfo	1.3.6.1.4.1.11.2.14.11.15.2.38.1.6.2
hpnicfPeriodicalNotification	1.3.6.1.4.1.11.2.14.11.15.2.38.1.6.3
hpnicfPeriodicalNotificationPrefix	1.3.6.1.4.1.11.2.14.11.15.2.38.1.6.3.0
NTF hpnicfPeriodicalTrap	1.3.6.1.4.1.11.2.14.11.15.2.38.1.6.3.0.1			If no trap occurs during the interval spicified by hpnicfPeriodicalTrapInterval, an hpnicfPeriodicalTrap will be generated. If the interval is set to 0, no hpnicfPeriodicalTrap will be generated.
hpnicfTrapDesInfo	1.3.6.1.4.1.11.2.14.11.15.2.38.1.7
hpnicfTrapDesInfoTable	1.3.6.1.4.1.11.2.14.11.15.2.38.1.7.1		not-accessible	A table of trap destination host address and port .
hpnicfTrapDesInfoEntry	1.3.6.1.4.1.11.2.14.11.15.2.38.1.7.1.1		not-accessible	The entry of trap destination host address and port.
I32 hpnicfTrapDesInfoIndex	1.3.6.1.4.1.11.2.14.11.15.2.38.1.7.1.1.1	Integer32	not-accessible	The index of this table.
IP hpnicfTrapDesIPAddress	1.3.6.1.4.1.11.2.14.11.15.2.38.1.7.1.1.2	IpAddress	read-create	The host IP address of the trap destination.
I32 hpnicfTrapDesPort	1.3.6.1.4.1.11.2.14.11.15.2.38.1.7.1.1.3	Integer32	read-create	The port of the trap destination.
ROW hpnicfTrapDesRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.38.1.7.1.1.4	RowStatus	read-create	The status of this table entry.
ADR hpnicfTrapDesAddrTAddress	1.3.6.1.4.1.11.2.14.11.15.2.38.1.7.1.1.5	TAddress	read-create	This object contains a transport address.
hpnicfTrapConfig	1.3.6.1.4.1.11.2.14.11.15.2.38.1.8
hpnicfTrapConfigTable	1.3.6.1.4.1.11.2.14.11.15.2.38.1.8.1		not-accessible	A table of trap configuration.
hpnicfTrapConfigEntry	1.3.6.1.4.1.11.2.14.11.15.2.38.1.8.1.1		not-accessible	The entry of trap configuration.
I32 hpnicfTrapConfigIndex	1.3.6.1.4.1.11.2.14.11.15.2.38.1.8.1.1.1	Integer32	not-accessible	The index of this table.
STR hpnicfTrapConfigName	1.3.6.1.4.1.11.2.14.11.15.2.38.1.8.1.1.2	SnmpAdminString	read-only	The name of the appointed traps.
STR hpnicfTrapConfigDescr	1.3.6.1.4.1.11.2.14.11.15.2.38.1.8.1.1.3	SnmpAdminString	read-write	The description of the appointed traps.
INT hpnicfTrapConfigSwitch	1.3.6.1.4.1.11.2.14.11.15.2.38.1.8.1.1.4	INTEGER	read-write	Indicates whether the specified traps should be generated.
INT hpnicfTrapConfigSwitch2	1.3.6.1.4.1.11.2.14.11.15.2.38.1.8.1.1.5	INTEGER	read-write	Indicates whether the specified traps should be generated. This node differs from hpnicfTrapConfigSwitch in value.

RFC description

Manages trap generation for table events like MAC table full, ARP table full, and network topology changes.

Start monitoring HP/H3C Comware router or switch (generic trap notifications) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HPN-ICF-TRAP-MIB

What Is HPN-ICF-TRAP-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description