HPN-ICF-IPV6-ADDRESS-MIB

All MIBs › HPN-ICF-IPV6-ADDRESS-MIB

Last Updated: 2006-03-15

Category: Technology: IPv6, Vendor: H3C/HH3C, Vendor: HP/HPE

Description: Manages IPv6 address assignment, prefix delegation, and stateless autoconfiguration on HP/Comware devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HPN-ICF-IPV6-ADDRESS-MIB?

HPN-ICF-IPV6-ADDRESS-MIB is an HP/Comware ICF MIB for managing IPv6 address assignment on device interfaces, including static configuration, prefix delegation, and stateless address autoconfiguration (SLAAC). It exposes configuration-oriented data describing which IPv6 addresses and prefixes are assigned to which interfaces and how they were obtained. Its monitoring role is primarily configuration/state visibility rather than classic hardware health: administrators use it to verify that expected IPv6 addresses are actually bound to interfaces and that autoconfiguration or delegation is functioning, catching address-assignment failures during IPv6 rollout. It complements standard IETF IPv6 MIBs (e.g., IP-MIB, IPV6-MIB) by adding HP/Comware-specific address-management detail. It is deployed on HP/H3C Comware routers and switches running dual-stack or IPv6-only network segments. Engineers can download the HPN-ICF-IPV6-ADDRESS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HPN-ICF-IPV6-ADDRESS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

HP/H3C Comware routers and switches

Monitoring Examples

The module description only states this MIB manages IPv6 addressing and no specific object or table names were supplied in the source excerpt, so a concrete polling walkthrough cannot be grounded in real identifiers here. Typically, an administrator would check per-interface assigned IPv6 addresses and their origin (manual, DHCPv6-PD, or SLAAC) to confirm an interface that should have received a delegated prefix actually did, rather than falling back to a link-local address only.

What Can Be Monitored

assigned IPv6 addresses per interface
prefix delegation state
stateless autoconfiguration status
address source/origin

Imported Objects

From HPN-ICF-OID-MIB

hpnicfCommon

OBJECT-IDENTITY

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
hpnicfIpv6AddrMIB	1.3.6.1.4.1.11.2.14.11.15.2.71			The MIB module for managing IPv6 address
hpnicfIpv6AddressObjects	1.3.6.1.4.1.11.2.14.11.15.2.71.1
hpnicfIpv6AddressConfig	1.3.6.1.4.1.11.2.14.11.15.2.71.1.1
hpnicfIpv6AddrSetTable	1.3.6.1.4.1.11.2.14.11.15.2.71.1.1.1		not-accessible	The table of address information is relevant to this entity's IPv6 addresses for setting. The address information that can be read and set in this table is a subset of the address information that can be read in hpnicfIpv6AddrReadTable and ipv6AddrTable in IPV6-MIB. This table is used to configure IPv6 addresses of an interface identified by hpnicfIpv6AddrSetIfIndex. When users create or delete an entry in this table, the agent also increases or reduces a corresponding entry in the hpnicfIpv6AddrReadTable and ipv6AddrTable in IPV6-MIB. When an interface which has been assigned IPv6 address is deleted, the agent also deletes the entry corresponding to the interface in this table and hpnicfIpv6AddrReadTable. All IPv6 addresses in this table will also show in ipv6AddrTable in IPV6-MIB.
hpnicfIpv6AddrSetEntry	1.3.6.1.4.1.11.2.14.11.15.2.71.1.1.1.1		not-accessible	Define the IPv6 address information.
I32 hpnicfIpv6AddrSetIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.71.1.1.1.1.1	Integer32	not-accessible	The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of RFC 1573's ifIndex.
IPt hpnicfIpv6AddrSetAddrType	1.3.6.1.4.1.11.2.14.11.15.2.71.1.1.1.1.2	InetAddressType	not-accessible	The IP address type to which this entry's address information pertains. The value must be ipv6.
IP hpnicfIpv6AddrSetAddr	1.3.6.1.4.1.11.2.14.11.15.2.71.1.1.1.1.3	InetAddress	not-accessible	The IPv6 address to which this entry's address information pertains.
I32 hpnicfIpv6AddrSetPfxLength	1.3.6.1.4.1.11.2.14.11.15.2.71.1.1.1.1.4	Integer32	read-create	The length of the prefix (in bits) associated with the IPv6 address of this entry.
INT hpnicfIpv6AddrSetSourceType	1.3.6.1.4.1.11.2.14.11.15.2.71.1.1.1.1.5	INTEGER	read-create	Indicate the type of source of IPv6 address. The value can be one of following: 'assignedIp': Assigned global/site-local IPv6 address; 'assignedEUI64Ip': Assigned global/site-local IPv6 address by using EUI-64 interface identifier; 'assignedLinklocalIp': Assigned link-local IPv6 address. The value of hpnicfIpv6AddrSetSourceType is relevant to hpnicfIpv6AddrReadSourceType and hpnicfIpv6AddrReadCatalog . For example, if the value of hpnicfIpv6AddrSetSourceType is set to 'assignedIp', then the value of hpnicfIpv6AddrReadSourceType is 'assignedIp' and the value of hpnicfIpv6AddrReadCatalog is 'global' or 'sitelocal'. The relation listed in the following table. ---------------------------------------------------------------- hpnicfIpv6Addr- \| hpnicfIpv6Addr- \| hpnicfIpv6Addr- SetSourceType \| ReadSourceType \| ReadCatalog ---------------------------------------------------------------- assignedIp \| assignedIp \| global or sitelocal ---------------------------------------------------------------- assignedEUI64Ip \| assignedEUI64Ip \| global or sitelocal ---------------------------------------------------------------- assignedLinklocalIp \| assignedIp \| linklocal ----------------------------------------------------------------
ROW hpnicfIpv6AddrSetRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.71.1.1.1.1.6	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table, only supports active(1), createAndGo(4) and destroy(6).
hpnicfIpv6AddrReadTable	1.3.6.1.4.1.11.2.14.11.15.2.71.1.1.2		not-accessible	The table of address information is relevant to this entity's IPv6 addresses for reading. This is the extension of the ipv6AddrTable in IPV6-MIB. All IPv6 addresses in this table will also show in ipv6AddrTable in IPV6-MIB.
hpnicfIpv6AddrReadEntry	1.3.6.1.4.1.11.2.14.11.15.2.71.1.1.2.1		not-accessible	Define the IPv6 address information.
I32 hpnicfIpv6AddrReadIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.71.1.1.2.1.1	Integer32	not-accessible	The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of RFC 1573's ifIndex.
IPt hpnicfIpv6AddrReadAddrType	1.3.6.1.4.1.11.2.14.11.15.2.71.1.1.2.1.2	InetAddressType	not-accessible	The IP address type to which this entry's address information pertains. The value must be ipv6.
IP hpnicfIpv6AddrReadAddr	1.3.6.1.4.1.11.2.14.11.15.2.71.1.1.2.1.3	InetAddress	not-accessible	The IPv6 address to which this entry's address information pertains.
I32 hpnicfIpv6AddrReadPfxLength	1.3.6.1.4.1.11.2.14.11.15.2.71.1.1.2.1.4	Integer32	read-only	The length of the prefix (in bits) associated with the IPv6 address of this entry.
INT hpnicfIpv6AddrReadSourceType	1.3.6.1.4.1.11.2.14.11.15.2.71.1.1.2.1.5	INTEGER	read-only	Indicate the type of source of IPv6 address. The value can be one of following: 'assignedIp': Assigned IPv6 address; 'assignedEUI64Ip': Assigned IPv6 address by using EUI-64 interface identifier; 'assignedAutoIp': Auto generated IPv6 address by user setting; 'autoIp': Auto generated IPv6 address as a result of non-linklocal anycast/unicast address configuration; 'dhcpv6': Assigned IPv6 address through DHCPv6 protocol; 'negotiate': Assigned IPv6 address through negotiation; 'cluster': Assigned IPv6 address through cluster module.
INT hpnicfIpv6AddrReadCatalog	1.3.6.1.4.1.11.2.14.11.15.2.71.1.1.2.1.6	INTEGER	read-only	Indicate the category of the IPv6 address. The value can be one of following: 'nodelocal': node-local scope; 'linklocal': link-local scope; 'sitelocal': site-local scope; 'orglocal': organization-local scope; 'global': global scope.

RFC description

HP/H3C IPv6 address management supporting configuration and reading of IPv6 addresses on interfaces with multiple origin types.

Start monitoring HP/H3C Comware routers and switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HPN-ICF-IPV6-ADDRESS-MIB

What Is HPN-ICF-IPV6-ADDRESS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description