HP-TUNNEL-MIB

All MIBs › HP-TUNNEL-MIB

Organization: HP Networking

Last Updated: 2015-02-02

Category: Domain: WAN, VPN and Security, Vendor: HP/HPE

Description: HP SNMP MIB for IP tunnel interface configuration and statistics including GRE and IPsec tunnels on HP networking devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HP-TUNNEL-MIB?

HP-TUNNEL-MIB is a Hewlett-Packard SNMP module for managing IP tunnel interfaces — including GRE and IPsec-style tunnels — on HP networking devices, along with VLAN-to-tunnel mapping. It exposes tunnel source/destination address configuration, per-tunnel MTU-drop diagnostic data, and VLAN tunnel mapping table entries. Its monitoring focus is tunnel software/interface health — specifically, catching packets being silently dropped because they exceed a tunnel's negotiated MTU, which explains intermittent application failures over a tunnel that otherwise looks up. It is a standalone HP module addressing tunnel management, conceptually related to but not a formal extension of the IETF's generic Tunnel MIB (RFC 4087). It is deployed on HP routers/switches terminating GRE or IPsec tunnels across a WAN or between sites needing VLAN extension over a tunnel. Engineers can download the HP-TUNNEL-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HP-TUNNEL-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

HP router/switch terminating GRE or IPsec tunnels

Monitoring Examples

An administrator can poll the hpTunnelMTUDrop objects — hpTunnelMTUDropTunnelSource/hpTunnelMTUDropTunnelDest, hpTunnelMTUDropRouterAddr, and hpTunnelMTUDropTunnelMTU — to identify a specific tunnel where oversized packets are being dropped due to an MTU mismatch, and could enable hpTunnelMTUDropNotifyEnable to get a trap the next time it happens. The hpicfVlanTunnelMappingTable/hpicfVlanTunnelMappingEntry, keyed by hpicfVLANIndex, would be checked to confirm a given VLAN is correctly mapped to its intended tunnel.

What Can Be Monitored

tunnel MTU-drop events
tunnel source/destination address
VLAN-to-tunnel mapping
MTU-drop notification state

Imported Objects

From HP-ICF-OID

hpSwitch

OBJECT-IDENTITY

From IF-MIB

InterfaceIndex

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From Q-BRIDGE-MIB

VlanIndex

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION

From TUNNEL-MIB

tunnelIfAddressType	OBJECT-TYPE
tunnelIfEntry	OBJECT-TYPE
tunnelIfLocalInetAddress	OBJECT-TYPE
tunnelIfRemoteInetAddress	OBJECT-TYPE
tunnelInetConfigEntry	OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
hpTunnelMIB	1.3.6.1.4.1.11.2.14.11.5.1.77			Renamed hpTunnelNotifications
hpTunnelNotifications	1.3.6.1.4.1.11.2.14.11.5.1.77.0
NTF hpTunnelIcmpErrorRcvd	1.3.6.1.4.1.11.2.14.11.5.1.77.0.1			This notification is generated when the tunnel source recevied an ICMP destination unreachable error message from the router in the underlay network with the IP address hpTunnelMTUDropRouterAddr for the reason of MTU violation.
hpTunnelObjects	1.3.6.1.4.1.11.2.14.11.5.1.77.1
hpTunnelConfigTable	1.3.6.1.4.1.11.2.14.11.5.1.77.1.1		not-accessible	This table is used to provision for a tunnel without having to configure the source and destination ends of the tunnels.
hpTunnelConfigEntry	1.3.6.1.4.1.11.2.14.11.5.1.77.1.1.1		not-accessible	A set of objects that are used to create a tunnel.
I32 hpTunnelID	1.3.6.1.4.1.11.2.14.11.5.1.77.1.1.1.1	Integer32	not-accessible	The tunnel number to configure a tunnel.
NUM hpTunnelIfIndex	1.3.6.1.4.1.11.2.14.11.5.1.77.1.1.1.2	InterfaceIndex	read-only	The interface index associated with this tunnel entry. Since this Object is read-only, it is deprecated in favor of hpTunnelInterfaceIndex.
ROW hpTunnelRowStatus	1.3.6.1.4.1.11.2.14.11.5.1.77.1.1.1.3	RowStatus	read-create	The status of this row, by which new entries may be created, or old entries deleted from this table.
NUM hpTunnelInterfaceIndex	1.3.6.1.4.1.11.2.14.11.5.1.77.1.1.1.4	InterfaceIndex	read-create	The tunnel interface index associated with this tunnel entry.
hpTunnelIfTable	1.3.6.1.4.1.11.2.14.11.5.1.77.1.2		not-accessible	This table augments the tunnelIfTable
hpTunnelIfEntry	1.3.6.1.4.1.11.2.14.11.5.1.77.1.2.1		not-accessible	A set of objects as an augment to tunnelIfTable.
INT hpTunnelIfPMTU	1.3.6.1.4.1.11.2.14.11.5.1.77.1.2.1.1	INTEGER	read-write	Enable/Disable path mtu discovery for this tunnel.
INT hpTunnelIfNUD	1.3.6.1.4.1.11.2.14.11.5.1.77.1.2.1.2	INTEGER	read-write	Enable/Disable Neighbor Unreachability Detection for this tunnel.
U32 hpTunnelIfMTU	1.3.6.1.4.1.11.2.14.11.5.1.77.1.2.1.3	Unsigned32	read-write	The size of the largest packet which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface.
HPT hpTunnelEncapsMethod	1.3.6.1.4.1.11.2.14.11.5.1.77.1.2.1.4	HpTunnelType	read-write	The encapsulation method used by the tunnel.
STR hpTunnelIpsecName	1.3.6.1.4.1.11.2.14.11.5.1.77.1.2.1.5	SnmpAdminString	read-write	Specifies the IPSEC profile name for tunnel. This mentioned IPSEC profile can be attached with tunnel to avail the protection for tunnel traffic
hpTunnelInetConfigTable	1.3.6.1.4.1.11.2.14.11.5.1.77.1.3		not-accessible	This table augments the tunnelInetConfigTable
hpTunnelInetConfigEntry	1.3.6.1.4.1.11.2.14.11.5.1.77.1.3.1		not-accessible	A set of objects as an augment to tunnelInetConfigTable.
HPT hpTunnelInetConfigEncapsMethod	1.3.6.1.4.1.11.2.14.11.5.1.77.1.3.1.1	HpTunnelType	read-write	The encapsulation method used by the tunnel.
hpicfVlanTunnelMappingTable	1.3.6.1.4.1.11.2.14.11.5.1.77.1.4		not-accessible	A table that maps a VLAN to a tunnel. The tunnel to VLAN mapping implies that tunnel will carry bidirectional traffic of a VLAN.
hpicfVlanTunnelMappingEntry	1.3.6.1.4.1.11.2.14.11.5.1.77.1.4.1		not-accessible	An entry containing the mapping of a VLAN to a tunnel. The VLAN-to-tunnel mapping allows all the VLAN traffic to flow through the associated tunnel.
VLA hpicfVLANIndex	1.3.6.1.4.1.11.2.14.11.5.1.77.1.4.1.1	VlanIndex	not-accessible	This object refers to the VLANID that is mapped to a tunnel
NUM hpicfTunnelIfIndex	1.3.6.1.4.1.11.2.14.11.5.1.77.1.4.1.2	InterfaceIndex	not-accessible	This object specifies the tunnel interface index which is mapped to a speciifc VLAN.
ROW hpicfVlanTunnelMappingRowStatus	1.3.6.1.4.1.11.2.14.11.5.1.77.1.4.1.3	RowStatus	read-create	The row status of a VLAN to tunnel mapping entry.
hpicfUDPTunnelTypeTable	1.3.6.1.4.1.11.2.14.11.5.1.77.1.5		not-accessible	A table containing the information about the UDP tunnel types.
hpicfUDPTunnelTypeEntry	1.3.6.1.4.1.11.2.14.11.5.1.77.1.5.1		not-accessible	An entry containing the information on a UDP tunnel type.
INT hpicfUDPTunnelType	1.3.6.1.4.1.11.2.14.11.5.1.77.1.5.1.1	INTEGER	read-create	This object is used to configure the UDP tunnel type. A value of none(0) indicates that the tunnel is not a UDP tunnel. A value of remotemirror(1) indicates that the UDP tunnel configured is a remote mirroring tunnel. A value of vxlan(2) indicates that the UDP tunnel configured is a VXLAN tunnel.
hpTunnelNotifyScalars	1.3.6.1.4.1.11.2.14.11.5.1.77.1.6
IPt hpTunnelMTUDropRouterAddrType	1.3.6.1.4.1.11.2.14.11.5.1.77.1.6.1	InetAddressType	accessible-for-notify	The IP address type of the router that sent the ICMP destination unreachable message.
IP hpTunnelMTUDropRouterAddr	1.3.6.1.4.1.11.2.14.11.5.1.77.1.6.2	InetAddress	accessible-for-notify	IP address of the router that sent the ICMP destination unreachable message.
I32 hpTunnelMTUDropRouterMTU	1.3.6.1.4.1.11.2.14.11.5.1.77.1.6.3	Integer32	accessible-for-notify	The interface MTU of the router that sent the ICMP destination unreachable message.
IPt hpTunnelMTUDropTunnelSrcAddrType	1.3.6.1.4.1.11.2.14.11.5.1.77.1.6.4	InetAddressType	accessible-for-notify	The address type of the source IP address of the original packet that is encapsulated by the VXLAN/Tap tunnel interface.
IP hpTunnelMTUDropTunnelSource	1.3.6.1.4.1.11.2.14.11.5.1.77.1.6.5	InetAddress	accessible-for-notify	The source IP address of the original packet that is encapsulated by the VXLAN/Tap tunnel interface.
IPt hpTunnelMTUDropTunnelDstAddrType	1.3.6.1.4.1.11.2.14.11.5.1.77.1.6.6	InetAddressType	accessible-for-notify	The address type of the destination IP address of the original packet that is encapsulated by the VXLAN/Tap tunnel interface.
IP hpTunnelMTUDropTunnelDest	1.3.6.1.4.1.11.2.14.11.5.1.77.1.6.7	InetAddress	accessible-for-notify	The destination IP address of the original packet that is encapsulated by the VXLAN/Tap tunnel interface.
NUM hpTunnelMTUDropInIfIndex	1.3.6.1.4.1.11.2.14.11.5.1.77.1.6.8	InterfaceIndex	accessible-for-notify	The interface index of the inbound VLAN of the ICMP destination unreachable packet.
INT hpTunnelMTUDropNotifyEnable	1.3.6.1.4.1.11.2.14.11.5.1.77.1.6.9	INTEGER	read-write	This enables or disables the virtual network notifications.
hpTunnelConformance	1.3.6.1.4.1.11.2.14.11.5.1.77.2
hpTunnelMIBCompliances	1.3.6.1.4.1.11.2.14.11.5.1.77.2.1
hpTunnelMIBCompliance	1.3.6.1.4.1.11.2.14.11.5.1.77.2.1.1			The compliance statement for the HP Tunnel MIB.
hpTunnelMIBCompliance2	1.3.6.1.4.1.11.2.14.11.5.1.77.2.1.2			The compliance statement for the HP Tunnel MIB.
hpTunnelMIBGroups	1.3.6.1.4.1.11.2.14.11.5.1.77.2.2
hpTunnelProvisionGroup	1.3.6.1.4.1.11.2.14.11.5.1.77.2.2.1			A collection of objects to support creation of a tunnel.
hpTunnelInetConfigGroup	1.3.6.1.4.1.11.2.14.11.5.1.77.2.2.2			A collection of objects to augment tunnelInetConfigTable.
hpVlanTunnelMappingGroup	1.3.6.1.4.1.11.2.14.11.5.1.77.2.2.3			A collection of objects to support VLAN to tunnel mapping.
hpTunnelProvisionGroup2	1.3.6.1.4.1.11.2.14.11.5.1.77.2.2.4			A collection of objects to support creation of a tunnel.
hpTunnelNotifyScalarsGroup	1.3.6.1.4.1.11.2.14.11.5.1.77.2.2.5			Group of objects required for notifications.
hpTunnelNotificationsGroup	1.3.6.1.4.1.11.2.14.11.5.1.77.2.2.6			The notifications for the VXLAN/Tap tunnels.

RFC description

HP Networking tunnel interface management supporting various encapsulation methods including IPsec and VXLAN.

Start monitoring HP router/switch terminating GRE or IPsec tunnels with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HP-TUNNEL-MIB

What Is HP-TUNNEL-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description