GALILEO-MIB

All MIBs › GALILEO-MIB

Category: Network Monitoring (RMON), Vendor: Galileo

Description: MIB for Galileo network management platform providing discovery, topology, and device monitoring objects.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is GALILEO-MIB?

Despite its short description describing a general "Galileo network management platform," GALILEO-MIB's actual objects (the "rl" prefix is RADLAN's vendor prefix, and "Galileo" refers to the Marvell/Galileo switch silicon family) reveal it to be a low-level switch-chip QoS and traffic-policy tuning module embedded in various RADLAN-based Ethernet switch firmwares. It exposes the chip's operating mode, over-provisioning and burst-size tuning for congestion policy, drop-precedence override behavior, and CoS flow-forwarding-table aging/polling parameters, plus a debug sub-tree for inspecting per-flow classification (FCOG) entries. This makes it a configuration and internal-diagnostic MIB for the switch's hardware QoS engine rather than a general fault/hardware-health MIB, useful for confirming that traffic-prioritization policy is tuned as intended and, via the debug objects, for inspecting how specific flows are being classified by the chip. It is an internal vendor/chip-specific MIB with no stated dependency on standard MIBs, tightly coupled to the Galileo silicon's own policy model. It would be found embedded in the management software of various Ethernet switches built around Marvell/Galileo switching silicon, most often accessed by vendor support engineers during deep QoS troubleshooting rather than routine monitoring. Engineers can download the GALILEO-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in GALILEO-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ethernet switch built on Marvell/Galileo switching silicon (RADLAN-based firmware)

Monitoring Examples

An engineer would check rlGalMode and rlGalModeAfterReset to confirm which chip operating mode is active and will persist across a reboot, and would review rlPolicyGalileoTuningOverProvisioning and rlPolicyGalileoTuningExtremConditionBurstSize when tuning how aggressively the switch reacts to congestion bursts. rlPolicyGalileoDebugFcogTable, keyed by rlPolicyGalileoDebugFcogType, would be inspected during a support escalation to see how the chip classified a specific flow (by rlPolicyGalileoDebugL2SrcAddr) and whether the observed rlPolicyGalileoDebugTuning matched the configured policy. rlCosFftAgingTimeout and rlCosFftPollingInterval would be checked if CoS classification appeared stale or slow to update.

What Can Be Monitored

chip operating mode
QoS over-provisioning/burst-size tuning
CoS flow table aging/polling interval
per-flow classification debug entries

Imported Objects

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero

From Q-BRIDGE-MIB

PortList

From RADLAN-MIB

rlGalileo

OBJECT-IDENTITY

From SNMPv2-SMI

IpAddress

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT rlGalMibVersion	1.3.6.1.4.1.89.56.1	INTEGER	read-only	MIB's version, the current version is 1.
INT rlGalMode	1.3.6.1.4.1.89.56.2	INTEGER	read-only	Current mode supported by the device.
INT rlGalModeAfterReset	1.3.6.1.4.1.89.56.3	INTEGER	read-write	New mode supported by the device after the next reset.
rlPolicyGalileoDebugTuning	1.3.6.1.4.1.89.56.4
INT rlPolicyGalileoTuningOverProvisioning	1.3.6.1.4.1.89.56.4.1	INTEGER	read-write	For non-quantitative flows: Defines the function that is used to devide the aggregate rate (dependent on the number of flows using the specific meterId). The options for this mib variables are: - overProvisioning is 1/n -> may cause severe exceeding from permitted bw. - minorOverProvisioning is 1/(n+1)-> may cause minor exceeding from permitted bw. - underProvisioning is 1/(2^n) -> usaully causes to be under the permitted bw. where n is the number of flows using the specific meterId, initial value = 1.
INT rlPolicyGalileoTuningExtremConditionBurstSize	1.3.6.1.4.1.89.56.4.2	INTEGER	read-write	This variable indicates the value of a new burst size, when the given aggregate burst size has reached the following extreme condition: (aggregateBurstSize/n) < 1536 (smaller than max MTU). The options for this mib variables are: - new burst = 0 bytes - new burst = 1536 bytes where n is the number of flows using the specific meterId.
T/F rlPolicyGalileoTuningOverrideOutOfProfileDropPrecedence	1.3.6.1.4.1.89.56.4.3	TruthValue	read-write	This mib variable is used only when the rlPolicyGalileoTuningExtremConditionBurstSize is 0 bytes. The options for this mib variables are: - TRUE => out of profile Drop Precedence = High Drop Precedence. This value will override the rule's out of profile Drop Precedence. - FALSE => out of profile Drop Precedence is set according to the rule's decision.
INT rlCosFftAgingTimeout	1.3.6.1.4.1.89.56.5	INTEGER	read-write	The aging timeout of the CoS FFT Tables.
INT rlCosFftPollingInterval	1.3.6.1.4.1.89.56.6	INTEGER	read-write	The polling interval for dynamic CoS FFTs support in seconds.
rlPolicyGalileoDebug	1.3.6.1.4.1.89.56.7
rlPolicyGalileoDebugFcogTable	1.3.6.1.4.1.89.56.7.1		not-accessible	Indecate the instance of the fcog for hash_fnc calc per group type
rlPolicyGalileoDebugFcogEntry	1.3.6.1.4.1.89.56.7.1.1		not-accessible	the entry per groupType indicate the offsets for hash_func calc.
RLP rlPolicyGalileoDebugFcogType	1.3.6.1.4.1.89.56.7.1.1.1	RlPolicyGalileoDebugGroupType	read-only	Specifies a the Group type for which Fcog bytes specified.
T/F rlPolicyGalileoDebugL2SrcAddr	1.3.6.1.4.1.89.56.7.1.1.2	TruthValue	read-write	indecate if the L2 SrcAddr defined for fcog.
T/F rlPolicyGalileoDebugL2DstAddr	1.3.6.1.4.1.89.56.7.1.1.3	TruthValue	read-write	indecate if the L2DstAddr defined for fcog.
T/F rlPolicyGalileoDebugVlanId	1.3.6.1.4.1.89.56.7.1.1.4	TruthValue	read-write	indecate if the VlanId defined for fcog.
T/F rlPolicyGalileoDebugInport	1.3.6.1.4.1.89.56.7.1.1.5	TruthValue	read-write	indecate if the Inport defined for fcog.
T/F rlPolicyGalileoDebugIpxDstNet	1.3.6.1.4.1.89.56.7.1.1.6	TruthValue	read-write	indecate if the IpxDstNet defined for fcog.
T/F rlPolicyGalileoDebugIpxDstNode	1.3.6.1.4.1.89.56.7.1.1.7	TruthValue	read-write	indecate if the IpxDstNode defined for fcog.
T/F rlPolicyGalileoDebugIpSrcAddr	1.3.6.1.4.1.89.56.7.1.1.8	TruthValue	read-write	indecate if the IpSrcAddr defined for fcog.
T/F rlPolicyGalileoDebugIpDstAddr	1.3.6.1.4.1.89.56.7.1.1.9	TruthValue	read-write	indecate if the IpDstAddr defined for fcog.
T/F rlPolicyGalileoDebugIpProtocol	1.3.6.1.4.1.89.56.7.1.1.10	TruthValue	read-write	indecate if the IpProtocol defined for fcog.
T/F rlPolicyGalileoDebugIpSrcPort	1.3.6.1.4.1.89.56.7.1.1.11	TruthValue	read-write	indecate if the IpSrcPort defined for fcog.
T/F rlPolicyGalileoDebugIpDstPort	1.3.6.1.4.1.89.56.7.1.1.12	TruthValue	read-write	indecate if the IpDstPort defined for fcog.
ROW rlPolicyGalileoDebugStatus	1.3.6.1.4.1.89.56.7.1.1.13	RowStatus	read-write	The status of a table entry. It is used to delete an entry from this table.
rlPolicyGalileoDebugFlowTable	1.3.6.1.4.1.89.56.7.2		not-accessible	This table will allow us to request variables from specific entry at the flowTable. only get and getNext will be supported (getNext will return alyaws EndOfMibTable)
rlPolicyGalileoDebugFlowTableEntry	1.3.6.1.4.1.89.56.7.2.1		not-accessible	all the input fileds has a default val except from the groupType, request of an entry should be based on the fcog definition.
RLP rlPolicyGalileoDebugFlowType	1.3.6.1.4.1.89.56.7.2.1.1	RlPolicyGalileoDebugGroupType	read-only	Specifies a the Group type.
INT rlPolicyGalileoDebugFlowRxIfIndex	1.3.6.1.4.1.89.56.7.2.1.2	INTEGER	read-only	Specifies a the IfIndex the packet arrived (for the calculation of the relevant cosTable.
OCT rlPolicyGalileoDebugFlowL2SrcAddr	1.3.6.1.4.1.89.56.7.2.1.3	OCTET STRING	read-only	Indicate the L2SrcAddr for the requsted entry.
OCT rlPolicyGalileoDebugFlowL2DstAddr	1.3.6.1.4.1.89.56.7.2.1.4	OCTET STRING	read-only	Indicate the L2DstAddr for the requsted entry.
INT rlPolicyGalileoDebugFlowVlanId	1.3.6.1.4.1.89.56.7.2.1.5	INTEGER	read-only	Indicate the VlanId for the requsted entry.
OCT rlPolicyGalileoDebugFlowIpxDstNet	1.3.6.1.4.1.89.56.7.2.1.6	OCTET STRING	read-only	Indicate the IPX DstNet for the requsted entry.
OCT rlPolicyGalileoDebugFlowIpxDstNode	1.3.6.1.4.1.89.56.7.2.1.7	OCTET STRING	read-only	Indicate the IPX DstNode for the requsted entry.
OCT rlPolicyGalileoDebugFlowIpSrcAddr	1.3.6.1.4.1.89.56.7.2.1.8	OCTET STRING	read-only	Indicate the IP SrcAddr for the requsted entry.
OCT rlPolicyGalileoDebugFlowIpDstAddr	1.3.6.1.4.1.89.56.7.2.1.9	OCTET STRING	read-only	Indicate the IP DstAddr for the requsted entry.
INT rlPolicyGalileoDebugFlowIpProtocol	1.3.6.1.4.1.89.56.7.2.1.10	INTEGER	read-only	Indicate the IP Protocol for the requsted entry.
OCT rlPolicyGalileoDebugFlowIpSrcPort	1.3.6.1.4.1.89.56.7.2.1.11	OCTET STRING	read-only	Indicate the IP SrcPort for the requsted entry.
OCT rlPolicyGalileoDebugFlowIpDstPort	1.3.6.1.4.1.89.56.7.2.1.12	OCTET STRING	read-only	Indicate the IP DstPort for the requsted entry.
T/F rlPolicyGalileoDebugFlowRetValid	1.3.6.1.4.1.89.56.7.2.1.13	TruthValue	read-only	Indicate if the requsted entry is valid (exist) or not.
T/F rlPolicyGalileoDebugFlowRetStatic	1.3.6.1.4.1.89.56.7.2.1.14	TruthValue	read-only	Indicate if the requsted entry is a static entry or not.
T/F rlPolicyGalileoDebugFlowRetAging	1.3.6.1.4.1.89.56.7.2.1.15	TruthValue	read-only	Indicate if the Aging bit of the requested entry is set or not.
INT rlPolicyGalileoDebugFlowRetCmd	1.3.6.1.4.1.89.56.7.2.1.16	INTEGER	read-only	Indicate if the CMD of the requested entry .
INT rlPolicyGalileoDebugFlowRetPrio	1.3.6.1.4.1.89.56.7.2.1.17	INTEGER	read-only	Indicate if the Pri/Sc of the requested entry .
INT rlPolicyGalileoDebugFlowRetInProfileDis	1.3.6.1.4.1.89.56.7.2.1.18	INTEGER	read-only	Indicate if the inProfile Discardability of the requested entry .
INT rlPolicyGalileoDebugFlowRetVpt	1.3.6.1.4.1.89.56.7.2.1.19	INTEGER	read-only	Indicate if the Vpt of the requested entry .
T/F rlPolicyGalileoDebugFlowRetChangeTos	1.3.6.1.4.1.89.56.7.2.1.20	TruthValue	read-only	Indicate if the Change Tos of the requested entry is set or not.
INT rlPolicyGalileoDebugFlowRetNewTos	1.3.6.1.4.1.89.56.7.2.1.21	INTEGER	read-only	Indicate if the New Tos of the requested entry.
INT rlPolicyGalileoDebugFlowRetVlanId	1.3.6.1.4.1.89.56.7.2.1.22	INTEGER	read-only	Indicate if the VlanId of the requested entry.
INT rlPolicyGalileoDebugFlowRetInIfIndex	1.3.6.1.4.1.89.56.7.2.1.23	INTEGER	read-only	Indicate if the InIfindex of the requested entry.
T/F rlPolicyGalileoDebugFlowRetEnableMeter	1.3.6.1.4.1.89.56.7.2.1.24	TruthValue	read-only	Indicate if Meter of the requested entry is enbled or not.
INT rlPolicyGalileoDebugFlowRetOutProfileDis	1.3.6.1.4.1.89.56.7.2.1.25	INTEGER	read-only	Indicate the outProfile Discardability of the requested entry .
INT rlPolicyGalileoFcuFwdCpuCounter	1.3.6.1.4.1.89.56.8	INTEGER	read-only	Count the number of packets that forward from the Flow Classification Unit to the CPU
rlPolicySimpleGalMib	1.3.6.1.4.1.89.56.9
INT rlPolicySimpleGalMibVersion	1.3.6.1.4.1.89.56.9.1	INTEGER	read-only	MIB's version, the current version is 1.
OCT rlPolicySimpleGalMibPortTypeSupport	1.3.6.1.4.1.89.56.9.2	OCTET STRING	read-only	return a bit mask that indicates the supported port type: ---------- \|87654321\| ---------- 1 - BoundaryType 2 - InteriorType
INT rlPolicySimpleGalMibRecalculateRules	1.3.6.1.4.1.89.56.9.3	INTEGER	read-write	Setting any value will cause recalculation of all the rules.
T/F rlPolicySimpleGalMibPolicyEnable	1.3.6.1.4.1.89.56.9.4	TruthValue	read-write	Enables or disables the policy feature
rlPolicySimpleGalMibProfileTable	1.3.6.1.4.1.89.56.9.5		not-accessible	The table defines all the profiles.
rlPolicySimpleGalMibProfileEntry	1.3.6.1.4.1.89.56.9.5.1		not-accessible	The entry define one profile.
INT rlPolicySimpleGalMibIndex	1.3.6.1.4.1.89.56.9.5.1.1	INTEGER	read-only	This enumerates the table entry.
STR rlPolicySimpleGalMibDescription	1.3.6.1.4.1.89.56.9.5.1.2	DisplayString	read-write	Informational text given by the user to describe the profile.
RLP rlPolicySimpleGalMibProfileType	1.3.6.1.4.1.89.56.9.5.1.3	RlPolicySimpleGalMibProfileType	read-write	Specifies a profile type.
INT rlPolicySimpleGalMibRate	1.3.6.1.4.1.89.56.9.5.1.4	INTEGER	read-write	The rate in kilobytes/second for the specified profile, or in the case of minDelay per session profile type the rate will indicate the rate per individual session
INT rlPolicySimpleGalMibBurstSize	1.3.6.1.4.1.89.56.9.5.1.5	INTEGER	read-write	The burst size parameter. A value of 0 means that the device should choose the Burst Size that is most suitable for the profile.
INT rlPolicySimpleGalMibMaxSession	1.3.6.1.4.1.89.56.9.5.1.6	INTEGER	read-write	Relevant only for the minDelay per session. Indicate the maximum number of sessions for this profile.
INT rlPolicySimpleGalMibNewVpt	1.3.6.1.4.1.89.56.9.5.1.7	INTEGER	read-write	Indicates the new VPT to assign to the packet.
T/F rlPolicySimpleGalMibChangeTosOrDscp	1.3.6.1.4.1.89.56.9.5.1.8	TruthValue	read-write	Indicates whether the TOS or DSCP should be remarked with a new value
INT rlPolicySimpleGalMibNewTosOrDscp	1.3.6.1.4.1.89.56.9.5.1.9	INTEGER	read-write	Indicates the new value for the TOS or DSCP. Relevant only if rlPolicySimpleGalMibChangeTosOrDscp is true.
ROW rlPolicySimpleGalMibStatus	1.3.6.1.4.1.89.56.9.5.1.10	RowStatus	read-write	The status of a table entry. It is used to delete an entry from this table.
rlPolicySimpleGalMibIpFcogTable	1.3.6.1.4.1.89.56.9.6		not-accessible	This table defines the used fields for ip classification, per port type (interior/boundary)
rlPolicySimpleGalMibIpFcogEntry	1.3.6.1.4.1.89.56.9.6.1		not-accessible	the entry define the used fields for classification
RLP rlPolicySimpleGalMibIpFcogPortType	1.3.6.1.4.1.89.56.9.6.1.1	RlPolicySimpleGalMibPortType	read-only	The port type (interior/boundary) to which this entry applies.
T/F rlPolicySimpleGalMibIpFcogTosOrDscp	1.3.6.1.4.1.89.56.9.6.1.2	TruthValue	read-write	Indicates whether the IP TOS or DSCP field will be used in classifiers or not.
T/F rlPolicySimpleGalMibIpFcogProtocol	1.3.6.1.4.1.89.56.9.6.1.3	TruthValue	read-write	Indicates whether the IP L4 protocol field will be used in classifiers or not.
INT rlPolicySimpleGalMibIpFcogSrcIpMask	1.3.6.1.4.1.89.56.9.6.1.4	INTEGER	read-write	Indicates the number of most significant bits of the Ip Address that are used in specifying IP source addresses in classifiers.
INT rlPolicySimpleGalMibIpFcogDstIpMask	1.3.6.1.4.1.89.56.9.6.1.5	INTEGER	read-write	Indicates the number of most significant bits of the Ip Address that are used in specifying IP destination addresses in classifiers.
T/F rlPolicySimpleGalMibIpFcogSrcPort	1.3.6.1.4.1.89.56.9.6.1.6	TruthValue	read-write	Indicates whether the IP L4 protocol source port field will be used in classifiers or not.
T/F rlPolicySimpleGalMibIpFcogDstPort	1.3.6.1.4.1.89.56.9.6.1.7	TruthValue	read-write	Indicates whether the IP L4 protocol destination port field will be used in classifiers or not.
T/F rlPolicySimpleGalMibIpFcogInIfIndex	1.3.6.1.4.1.89.56.9.6.1.8	TruthValue	read-write	Indicates whether ifIndex of input ports will be used in classifiers or not.
rlPolicySimpleGalMibIpRulesTable	1.3.6.1.4.1.89.56.9.7		not-accessible	This table contains the policy rules defined by the user. The order of the entries in the table is important, since the first rule that applies to the incoming packet will be acted upon, ignoring any further rules that may apply as well.
rlPolicySimpleGalMibIpRulesEntry	1.3.6.1.4.1.89.56.9.7.1		not-accessible	This entry defines one policy rule.
RLP rlPolicySimpleGalMibIpRulesPortType	1.3.6.1.4.1.89.56.9.7.1.1	RlPolicySimpleGalMibPortType	read-only	The port type (interior/boundary) to which this rule applies.
INT rlPolicySimpleGalMibIpRulesIndex	1.3.6.1.4.1.89.56.9.7.1.2	INTEGER	read-only	This enumerates the table. The user should assign indices in such a way that there will be a gap big enough between one rule and the next to allow insertion of additional rules in between (a gap of 1000 is recommended).
STR rlPolicySimpleGalMibIpRulesDescription	1.3.6.1.4.1.89.56.9.7.1.3	DisplayString	read-write	Informational text given by the user to describe the rule.
INT rlPolicySimpleGalMibIpRulesTosOrDscp	1.3.6.1.4.1.89.56.9.7.1.4	INTEGER	read-write	Indicates the TOS or DSCP to compare with.
INT rlPolicySimpleGalMibIpRulesProtocol	1.3.6.1.4.1.89.56.9.7.1.5	INTEGER	read-write	Indicates the L4 protocol to compare with.
IP rlPolicySimpleGalMibIpRulesSrcIp	1.3.6.1.4.1.89.56.9.7.1.6	IpAddress	read-write	Indicates the source IP address to compare with.
INT rlPolicySimpleGalMibIpRulesSrcIpMask	1.3.6.1.4.1.89.56.9.7.1.7	INTEGER	read-write	Indicates the number of most significant bits of the Ip Address that are used in specifying IP source addresses in classifiers.
IP rlPolicySimpleGalMibIpRulesDstIp	1.3.6.1.4.1.89.56.9.7.1.8	IpAddress	read-write	Indicates the destination IP address to compare with.
INT rlPolicySimpleGalMibIpRulesDstIpMask	1.3.6.1.4.1.89.56.9.7.1.9	INTEGER	read-write	Indicates the number of most significant bits of the Ip Address that are used in specifying IP destination addresses in classifiers.
INT rlPolicySimpleGalMibIpRulesSrcPort	1.3.6.1.4.1.89.56.9.7.1.10	INTEGER	read-write	Indicates the source L4 port to compare with.
INT rlPolicySimpleGalMibIpRulesDstPort	1.3.6.1.4.1.89.56.9.7.1.11	INTEGER	read-write	Indicates the destination L4 port to compare with.
POR rlPolicySimpleGalMibIpRulesInIfIndexList	1.3.6.1.4.1.89.56.9.7.1.12	PortList	read-write	Indicates the list of input ports to which this rule applies.
INT rlPolicySimpleGalMibIpRulesCondition	1.3.6.1.4.1.89.56.9.7.1.13	INTEGER	read-write	Indicate the relation that should hold for each relevant field of the rule in comparison to the packet's field.
INT rlPolicySimpleGalMibIpRulesAction	1.3.6.1.4.1.89.56.9.7.1.14	INTEGER	read-write	Indicates the action to be performed if there is a match with the rule.
INT rlPolicySimpleGalMibIpRulesProfilePointer	1.3.6.1.4.1.89.56.9.7.1.15	INTEGER	read-write	Indicates the profile attached to the rule. The value is the index in the profile table of the attached profile. Value 0 means that no profile is attached to the rule and is valid only in case of action block.
POR rlPolicySimpleGalMibIpRulesOutIfIndexList	1.3.6.1.4.1.89.56.9.7.1.16	PortList	read-write	Indicates the list of output ports to on which bandwidth should be allocated for this rule.
OCT rlPolicySimpleGalMibIpRulesBitsUsed	1.3.6.1.4.1.89.56.9.7.1.17	OCTET STRING	read-write	a bit mask that indicates the the used fields for the entry: (the implemention is identical to BITS implementation,from MSB to LSB) ---------- \|87654321\| ---------- 8 - tosOrDscp 7 - Protocol 6 - SrcIp 5 - DstIp 4 - SrcIpPort 3 - DstIpPort
STR rlPolicySimpleGalMibIpRulesErrorDescrip	1.3.6.1.4.1.89.56.9.7.1.18	DisplayString	read-only	A description error indicate the user about the specific error. The error can cause by one of the following reasons: 1. if the profile was asign to the rule could not be perform 2. if the operation of QoS portLock failed
ROW rlPolicySimpleGalMibIpRulesStatus	1.3.6.1.4.1.89.56.9.7.1.19	RowStatus	read-write	The status of a table entry. It is used to delete an entry from this table. notInService is used to disable an entry. notReady will be assigned by the device to indicate that the rule can not be active because some ports in the output ports list are not in a state allowing bandwidth allocation guarantee.
rlPolicySimpleGalMibIpxFcogTable	1.3.6.1.4.1.89.56.9.8		not-accessible	This table defines the used fields for ipx classification
rlPolicySimpleGalMibIpxFcogEntry	1.3.6.1.4.1.89.56.9.8.1		not-accessible	the entry defines the used fields for classification
INT rlPolicySimpleGalMibIpxFcogIndex	1.3.6.1.4.1.89.56.9.8.1.1	INTEGER	read-only	the table index - only one entry exist
OCT rlPolicySimpleGalMibIpxFcogDstNet	1.3.6.1.4.1.89.56.9.8.1.2	OCTET STRING	read-write	Indicates the parts of the field in use in the rules
OCT rlPolicySimpleGalMibIpxFcogDstNode	1.3.6.1.4.1.89.56.9.8.1.3	OCTET STRING	read-write	Indicates the parts of the field in use in the rules
T/F rlPolicySimpleGalMibIpxFcogDstSocket	1.3.6.1.4.1.89.56.9.8.1.4	TruthValue	read-write	Indicates whether the field is in use in the rules
OCT rlPolicySimpleGalMibIpxFcogSrcNet	1.3.6.1.4.1.89.56.9.8.1.5	OCTET STRING	read-write	Indicates the parts of the field in use in the rules
OCT rlPolicySimpleGalMibIpxFcogSrcNode	1.3.6.1.4.1.89.56.9.8.1.6	OCTET STRING	read-write	Indicates the parts of the field in use in the rules
T/F rlPolicySimpleGalMibIpxFcogSrcSocket	1.3.6.1.4.1.89.56.9.8.1.7	TruthValue	read-write	Indicates whether the field is in use in the rules
T/F rlPolicySimpleGalMibIpxFcogInIfIndex	1.3.6.1.4.1.89.56.9.8.1.8	TruthValue	read-write	Indicates whether the field is in use in the rules
rlPolicySimpleGalMibIpxRulesTable	1.3.6.1.4.1.89.56.9.9		not-accessible	This table contains the policy rules defined by the user. The order of the entries in the table is important, since the first rule that matches the incoming packet will be acted upon, ignoring any further rules that may match as well.
rlPolicySimpleGalMibIpxRulesEntry	1.3.6.1.4.1.89.56.9.9.1		not-accessible	This entry defines one policy rule.
INT rlPolicySimpleGalMibIpxRulesIndex	1.3.6.1.4.1.89.56.9.9.1.1	INTEGER	read-only	This enumerates the table. The user should assign indices in such a way that there will be a gap big enough between one rule and the next to allow insertion of additional rules in between (a gap of 1000 is recommended).
STR rlPolicySimpleGalMibIpxRulesDescription	1.3.6.1.4.1.89.56.9.9.1.2	DisplayString	read-write	Informational text given by the user to describe the rule.
OCT rlPolicySimpleGalMibIpxRulesDstNet	1.3.6.1.4.1.89.56.9.9.1.3	OCTET STRING	read-write	Indicate the ipxDst Net to compare to
OCT rlPolicySimpleGalMibIpxRulesDstNode	1.3.6.1.4.1.89.56.9.9.1.4	OCTET STRING	read-write	Indicate the ipxDstNode to compare to
INT rlPolicySimpleGalMibIpxRulesDstSocket	1.3.6.1.4.1.89.56.9.9.1.5	INTEGER	read-write	Indicate the ipx DstSocket to compare to
OCT rlPolicySimpleGalMibIpxRulesSrcNet	1.3.6.1.4.1.89.56.9.9.1.6	OCTET STRING	read-write	Indicate the ipxSrc Net to compare to
OCT rlPolicySimpleGalMibIpxRulesSrcNode	1.3.6.1.4.1.89.56.9.9.1.7	OCTET STRING	read-write	Indicate the ipxSrcNode to compare to
INT rlPolicySimpleGalMibIpxRulesSrcSocket	1.3.6.1.4.1.89.56.9.9.1.8	INTEGER	read-write	Indicate the ipx SrcSocket to compare to
POR rlPolicySimpleGalMibIpxRulesInIfIndexList	1.3.6.1.4.1.89.56.9.9.1.9	PortList	read-write	Indicates the list of input ports to which this rule applies.
INT rlPolicySimpleGalMibIpxRulesCondition	1.3.6.1.4.1.89.56.9.9.1.10	INTEGER	read-write	Indicate the relation that should hold for each relevant field of the rule in comparison to the packet's.
INT rlPolicySimpleGalMibIpxRulesAction	1.3.6.1.4.1.89.56.9.9.1.11	INTEGER	read-write	Indicates the action to be performed if the rule matches.
INT rlPolicySimpleGalMibIpxRulesProfilePointer	1.3.6.1.4.1.89.56.9.9.1.12	INTEGER	read-write	Indicates the profile attached to the rule. The value is the index in the profile table of the attached profile. Value 0 means that no profile is attached to the rule and is valid only in case of action block.
POR rlPolicySimpleGalMibIpxRulesOutIfIndexList	1.3.6.1.4.1.89.56.9.9.1.13	PortList	read-write	Indicates the list of output ports on which bandwidth should be allocated for this rule.
ROW rlPolicySimpleGalMibIpxRulesStatus	1.3.6.1.4.1.89.56.9.9.1.14	RowStatus	read-write	The status of a table entry. It is used to delete an entry from this table. notInService is used to disable an entry. notReady will be assigned by the device to indicate that the rule can not be active because some ports in the output ports list are not in a state allowing bandwidth allocation guarantee.
rlPolicySimpleGalMibBridgeFcogTable	1.3.6.1.4.1.89.56.9.10		not-accessible	The table defines the used fields for Bridge classification
rlPolicySimpleGalMibBridgeFcogEntry	1.3.6.1.4.1.89.56.9.10.1		not-accessible	the entry defines the used fields for classification
INT rlPolicySimpleGalMibBridgeFcogIndex	1.3.6.1.4.1.89.56.9.10.1.1	INTEGER	read-only	the table index - only one entry exist
OCT rlPolicySimpleGalMibBridgeFcogDstMac	1.3.6.1.4.1.89.56.9.10.1.2	OCTET STRING	read-write	Indicate the use of the field in the rules
OCT rlPolicySimpleGalMibBridgeFcogSrcMac	1.3.6.1.4.1.89.56.9.10.1.3	OCTET STRING	read-write	Indicate the use of the field in the rules
T/F rlPolicySimpleGalMibBridgeFcogVid	1.3.6.1.4.1.89.56.9.10.1.4	TruthValue	read-write	Indicate whether the field is in use in the rules
T/F rlPolicySimpleGalMibBridgeFcogInIfIndex	1.3.6.1.4.1.89.56.9.10.1.5	TruthValue	read-write	Indicate whether the field is in use in the rules
T/F rlPolicySimpleGalMibBridgeFcogEthType	1.3.6.1.4.1.89.56.9.10.1.6	TruthValue	read-write	Indicate whether the field is in use in the rules
T/F rlPolicySimpleGalMibBridgeFcogIpTosOrDscp	1.3.6.1.4.1.89.56.9.10.1.7	TruthValue	read-write	Indicate whether the field is in use in the rules
T/F rlPolicySimpleGalMibBridgeFcogIpProtocol	1.3.6.1.4.1.89.56.9.10.1.8	TruthValue	read-write	Indicate whether the field is in use in the rules
INT rlPolicySimpleGalMibBridgeFcogIpSrcIpMask	1.3.6.1.4.1.89.56.9.10.1.9	INTEGER	read-write	Indicate the number of used bits of the Ip Address from the left
INT rlPolicySimpleGalMibBridgeFcogIpDstIpMask	1.3.6.1.4.1.89.56.9.10.1.10	INTEGER	read-write	Indicate the number of used bits of the Ip Address from the left
T/F rlPolicySimpleGalMibBridgeFcogIpSrcPort	1.3.6.1.4.1.89.56.9.10.1.11	TruthValue	read-write	Indicate whether the field is in use in the rules
T/F rlPolicySimpleGalMibBridgeFcogIpDstPort	1.3.6.1.4.1.89.56.9.10.1.12	TruthValue	read-write	Indicate whether the field is in use in the rules
rlPolicySimpleGalMibBridgeRulesTable	1.3.6.1.4.1.89.56.9.11		not-accessible	This table contains the policy rules defined by the user. The order of the entries in the table is important, since the first rule that applies to the incoming packet will be acted upon, ignoring any further rules that may apply as well.
rlPolicySimpleGalMibBridgeRulesEntry	1.3.6.1.4.1.89.56.9.11.1		not-accessible	This entry defines one policy rule.
INT rlPolicySimpleGalMibBridgeRulesIndex	1.3.6.1.4.1.89.56.9.11.1.1	INTEGER	read-only	This enumerates the table. The user should assign indices in such a way that there will be a gap big enough between one rule and the next to allow insertion of additional rules in between (a gap of 1000 is recommended).
STR rlPolicySimpleGalMibBridgeRulesDescription	1.3.6.1.4.1.89.56.9.11.1.2	DisplayString	read-write	Informational text given by the user to describe the rule.
OCT rlPolicySimpleGalMibBridgeRulesDstMac	1.3.6.1.4.1.89.56.9.11.1.3	OCTET STRING	read-write	Indicate the Dst mac to compare
OCT rlPolicySimpleGalMibBridgeRulesSrcMac	1.3.6.1.4.1.89.56.9.11.1.4	OCTET STRING	read-write	Indicate the source mac to compare
INT rlPolicySimpleGalMibBridgeRulesVid	1.3.6.1.4.1.89.56.9.11.1.5	INTEGER	read-write	Indicate the vlanId to compare
POR rlPolicySimpleGalMibBridgeRulesInIfIndexList	1.3.6.1.4.1.89.56.9.11.1.6	PortList	read-write	Indicates the list of input ports to which this rule applies.
INT rlPolicySimpleGalMibBridgeRulesEthType	1.3.6.1.4.1.89.56.9.11.1.7	INTEGER	read-write	Indicate the Ethernet type of the packet
INT rlPolicySimpleGalMibBridgeRulesIpTosOrDscp	1.3.6.1.4.1.89.56.9.11.1.8	INTEGER	read-write	Indicates the tos or dscp to compare
INT rlPolicySimpleGalMibBridgeRulesIpProtocol	1.3.6.1.4.1.89.56.9.11.1.9	INTEGER	read-write	Indicates the protocol to compare
IP rlPolicySimpleGalMibBridgeRulesIpSrcIp	1.3.6.1.4.1.89.56.9.11.1.10	IpAddress	read-write	Indicate the srcIp to compare
IP rlPolicySimpleGalMibBridgeRulesIpDstIp	1.3.6.1.4.1.89.56.9.11.1.11	IpAddress	read-write	Indicate the DstIp to compare
INT rlPolicySimpleGalMibBridgeRulesIpSrcPort	1.3.6.1.4.1.89.56.9.11.1.12	INTEGER	read-write	Indicate the Src port to compare
INT rlPolicySimpleGalMibBridgeRulesIpDstPort	1.3.6.1.4.1.89.56.9.11.1.13	INTEGER	read-write	Indicate the Src port to compare
INT rlPolicySimpleGalMibBridgeRulesCondition	1.3.6.1.4.1.89.56.9.11.1.14	INTEGER	read-write	Indicate the relation that should hold for each relevant field of the rule in comparison to the packet's field.
INT rlPolicySimpleGalMibBridgeRulesAction	1.3.6.1.4.1.89.56.9.11.1.15	INTEGER	read-write	Indicates the action to be performed if there is a match with the rule.
INT rlPolicySimpleGalMibBridgeRulesProfilePointer	1.3.6.1.4.1.89.56.9.11.1.16	INTEGER	read-write	Indicates the profile attached to the rule. The value is the index in the profile table of the attached profile. Value 0 means that no profile is attached to the rule and is valid only in case of action block.
POR rlPolicySimpleGalMibBridgeRulesOutIfIndexList	1.3.6.1.4.1.89.56.9.11.1.17	PortList	read-write	Indicates the list of output ports to on which bandwidth should be allocated for this rule.
ROW rlPolicySimpleGalMibBridgeRulesStatus	1.3.6.1.4.1.89.56.9.11.1.18	RowStatus	read-write	The status of a table entry. It is used to delete an entry from this table. notInService is used to disable an entry. notReady will be assigned by the device to indicate that the rule can not be active because some ports in the output ports list are not in a state allowing bandwidth allocation guarantee.
rlPolicySimpleGalMibPortTable	1.3.6.1.4.1.89.56.9.12		not-accessible	The table defines all of the ports types
rlPolicySimpleGalMibPortEntry	1.3.6.1.4.1.89.56.9.12.1		not-accessible	An entry defines a port's type
INT rlPolicySimpleGalMibPortIfIndex	1.3.6.1.4.1.89.56.9.12.1.1	INTEGER	read-only	This enumerates the table entry.
RLP rlPolicySimpleGalMibPortType	1.3.6.1.4.1.89.56.9.12.1.2	RlPolicySimpleGalMibPortType	read-write	Defines the port type
INT rlGalPolicyMode	1.3.6.1.4.1.89.56.10	INTEGER	read-only	Indicates whether the QoS is for: -All Bridged packets; or -All routed IP packets. The value cannot change after system init

RFC description

Manages RADLAN ROS Galileo mode configuration and policy tuning for network switches.

Start monitoring Ethernet switch on Marvell/Galileo switching silicon (RADLAN-based firmware, QoS chip tuning) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download GALILEO-MIB

What Is GALILEO-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description