FD-SYSTEM-MIB

All MIBs › FD-SYSTEM-MIB

Organization: epon eoc factory.

Last Updated: 2010-05-27

Category: Device Management, Domain: DSL/xPON, Hardware and Environment, Technology: EPON/PON, Vendor: C-Data

Description: C-Data FD-series system-level MIB for device identity, firmware version, and system configuration on FD-platform OLTs.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is FD-SYSTEM-MIB?

FD-SYSTEM-MIB is a C-Data Technology proprietary MIB providing system-level management for its FD-series platform, which includes GPON/EPON Optical Line Terminal (OLT) equipment used in fiber access networks. It exposes basic device-identity and system-configuration data such as device model/type, firmware/software version, and general system settings. Its main monitoring value is confirming the software/firmware identity and baseline configuration state of the OLT chassis, useful for inventory tracking and verifying a device is running the expected firmware version. FD-SYSTEM-MIB SNMP monitoring therefore centers on identity and configuration verification rather than live traffic or hardware sensor data. It is a foundational, vendor-specific module that typically coexists with, and is indexed alongside, the standard SNMPv2 System group (sysDescr, sysUpTime) and other C-Data FD-series MIBs covering interfaces or PON-specific data. It is deployed on C-Data FD-series OLT and related access-network hardware used by ISPs and fiber network operators.

IPNetwork Monitor allows you to monitor SNMP objects defined in FD-SYSTEM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

C-Data FD1616S-B2 — current 1U 16-port GPON OLT (ITU G.984/FSAN compliant, up to 1:128 split), part of C-Data's actively sold FD-series OLT lineup

Monitoring Examples

No specific object or table names were captured for this MIB, so exact polling targets cannot be confirmed, but consistent with being a system mib module an admin would expect to poll system identity/version objects to confirm the OLT's model, hardware revision, and running firmware version, and to detect an unexpected firmware version after a maintenance window or a device that has silently reset.

What Can Be Monitored

device model/hardware identity
firmware/software version
system configuration state

Imported Objects

From EPON-EOC-MIB

DeviceOperation
DeviceStatus
DeviceType
LedStatus
epon	OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
MacAddress
RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
systemInfo	1.3.6.1.4.1.34592.1.3.1			system mib module
sysBaseInfo	1.3.6.1.4.1.34592.1.3.1.1
DEV sysModel	1.3.6.1.4.1.34592.1.3.1.1.1	DeviceType	read-only	OLT platform system model
STR sysDesc	1.3.6.1.4.1.34592.1.3.1.1.2	DisplayString	read-write	Used for system manager to give a brief system description information
STR sysLocation	1.3.6.1.4.1.34592.1.3.1.1.3	DisplayString	read-write	Used for system manager to input the device(olt platform) location information
STR sysContact	1.3.6.1.4.1.34592.1.3.1.1.4	DisplayString	read-write	system manager contact information
LED sysMajAlarmLed	1.3.6.1.4.1.34592.1.3.1.1.5	LedStatus	read-only	Status of main card MAJ led
LED sysCriAlarmLed	1.3.6.1.4.1.34592.1.3.1.1.6	LedStatus	read-only	Status of main card CRJ led
STR sysAlarmDesc	1.3.6.1.4.1.34592.1.3.1.1.7	DisplayString	read-only	Meaning of MAJ and CRI alarm leds. Normally, you can get alarm meaning from this object when one of or both the MAJ and CRI alarm leds are lip
sysConfig	1.3.6.1.4.1.34592.1.3.1.2
INT consolePortSpd	1.3.6.1.4.1.34592.1.3.1.2.1	INTEGER	read-only	Main card CONSOLE port access speed
IP manageIpAddr	1.3.6.1.4.1.34592.1.3.1.2.2	IpAddress	read-write	The IP Address of outband network management port
IP manageNetMask	1.3.6.1.4.1.34592.1.3.1.2.3	IpAddress	read-write	The network mask of outband network management port
IP manageGateway	1.3.6.1.4.1.34592.1.3.1.2.4	IpAddress	read-write	The Default Gateway Address of outband network management port
STR snmpReadCommunity	1.3.6.1.4.1.34592.1.3.1.2.5	DisplayString	read-write	The read-only community used on the embedded snmp agent
STR snmpRWCommunity	1.3.6.1.4.1.34592.1.3.1.2.6	DisplayString	read-write	The read-write community used on the embedded snmp agent
IP trapDstIpAddr1	1.3.6.1.4.1.34592.1.3.1.2.8	IpAddress	read-write	The first destination IP Address to which the system trap will send
IP trapDstIpAddr2	1.3.6.1.4.1.34592.1.3.1.2.9	IpAddress	read-write	The second destination IP Address to which the system trap will send
IP trapDstIpAddr3	1.3.6.1.4.1.34592.1.3.1.2.10	IpAddress	read-write	The third destination IP Address to which the system trap will send
IP trapDstIpAddr4	1.3.6.1.4.1.34592.1.3.1.2.11	IpAddress	read-write	The fourth destination IP Address to which the system trap will send
DEV sysOperate	1.3.6.1.4.1.34592.1.3.1.2.12	DeviceOperation	read-write	Set the value of this object to 'save(1)' to save all system configurations. Return 'noOperation(2)' when read. Set the value to 'noOperation(2)'will take nothing effect
chassisInfo	1.3.6.1.4.1.34592.1.3.1.3
DEV chassisType	1.3.6.1.4.1.34592.1.3.1.3.1	DeviceType	read-only	type of the olt platform chassis
OCT chassisFactorySerial	1.3.6.1.4.1.34592.1.3.1.3.2	OCTET STRING	read-only	Description. Chassis factory serial,reserved for future use.
STR chassisRevision	1.3.6.1.4.1.34592.1.3.1.3.3	DisplayString	read-only	Description.
U32 chassisTemperature	1.3.6.1.4.1.34592.1.3.1.3.4	Unsigned32	read-only	chassis temperature
U32 powerStatusBit	1.3.6.1.4.1.34592.1.3.1.3.5	Unsigned32	read-only	Power status bit masks; value & 1 == 1 indicating power A on else off value & 2 == 2 indicating power B on else off
U32 fanStatusBit	1.3.6.1.4.1.34592.1.3.1.3.6	Unsigned32	read-only	Fan stauts bit masks value & 1 == 1 indicating fan 1 on else off value & 2 == 2 indicating fan 2 on else off value & 4 == 4 indicating fan 3 on else off value & 8 == 8 indicating fan 4 on else off
cardModule	1.3.6.1.4.1.34592.1.3.1.5
mainCard	1.3.6.1.4.1.34592.1.3.1.5.1
DEV mainCardType	1.3.6.1.4.1.34592.1.3.1.5.1.1	DeviceType	read-only	type of main card (it is also called control and switch card)
OCT mainCardFactorySerial	1.3.6.1.4.1.34592.1.3.1.5.1.2	OCTET STRING	read-only	Description. Main card factory serial, reserved for future use
STR mainCardHWRevision	1.3.6.1.4.1.34592.1.3.1.5.1.3	DisplayString	read-only	main card hardware revision
STR mainCardSWVersion	1.3.6.1.4.1.34592.1.3.1.5.1.4	DisplayString	read-only	software version running on main card
DEV mainCardRunningStatus	1.3.6.1.4.1.34592.1.3.1.5.1.5	DeviceStatus	read-only	The running status of main card, it can only be normal or abnormal, since the main card is always online
TIK mainCardRunningTime	1.3.6.1.4.1.34592.1.3.1.5.1.6	TimeTicks	read-only	The running time since the main card was last powered
DEV mainCardOperate	1.3.6.1.4.1.34592.1.3.1.5.1.7	DeviceOperation	read-write	The operation collection, such as reset, restore...
ponCard	1.3.6.1.4.1.34592.1.3.1.5.2
ponCardTable	1.3.6.1.4.1.34592.1.3.1.5.2.1		not-accessible	This table defines base para objects of PON cards installed in the chassis
ponCardEntry	1.3.6.1.4.1.34592.1.3.1.5.2.1.1		not-accessible	Each entry defines a sole PON card objects
I32 ponCardSlotId	1.3.6.1.4.1.34592.1.3.1.5.2.1.1.1	Integer32	not-accessible	PON card slot index, defined begin from 1 to max slot number
DEV ponCardType	1.3.6.1.4.1.34592.1.3.1.5.2.1.1.2	DeviceType	read-only	PON card type value
OCT ponCardFactorySerial	1.3.6.1.4.1.34592.1.3.1.5.2.1.1.3	OCTET STRING	read-only	Description. PON card factory serial, reserved for future use
STR ponCardHwRev	1.3.6.1.4.1.34592.1.3.1.5.2.1.1.4	DisplayString	read-only	PON card hardware revision
STR ponCardFwVer	1.3.6.1.4.1.34592.1.3.1.5.2.1.1.5	DisplayString	read-only	PON card software version
DEV ponCardRunningStatus	1.3.6.1.4.1.34592.1.3.1.5.2.1.1.7	DeviceStatus	read-only	pon card on-line status, each pon card may have following status: not installed (present) installed but can not be connected by main card installed and can be connected by main card
TIK ponCardRuningTime	1.3.6.1.4.1.34592.1.3.1.5.2.1.1.8	TimeTicks	read-only	The running time since the pon card last powered
DEV ponCardOperate	1.3.6.1.4.1.34592.1.3.1.5.2.1.1.9	DeviceOperation	read-write	Operate action taken on PON card
INT ponCardUpgradeStat	1.3.6.1.4.1.34592.1.3.1.5.2.1.1.10	INTEGER	read-only	Description.
onuAuth	1.3.6.1.4.1.34592.1.3.1.6
INT authMethod	1.3.6.1.4.1.34592.1.3.1.6.1	INTEGER	read-write	Which method that the manager will take to authenticate accessed ONUs, When set to blackList, the OLT will allow only the ONUs that their MAC is not included in the black MAC table. When set to whiteList,the OLT will allow only the ONUs that their MAC is included in the white MAC table.
INT nonAuthOper	1.3.6.1.4.1.34592.1.3.1.6.2	INTEGER	read-write	ONU MAC Authentication operation object, now, it can only be used to clear the MAC list which had tried to register but had not been authenticated
onuAuthMacCfgTable	1.3.6.1.4.1.34592.1.3.1.6.3		not-accessible	MAC list table which contain the ONU MAC address list, these MAC address will be used to authenticate accessed ONUs.
onuAuthMacCfgEntry	1.3.6.1.4.1.34592.1.3.1.6.3.1		not-accessible	Each entry in this table defines a sole MAC (when the beginMAC is equal to the endMAC or the endMAC is blank/zero) or a MAC range.
U32 authMacEntryId	1.3.6.1.4.1.34592.1.3.1.6.3.1.1	Unsigned32	not-accessible	Description. entry serial ID, which used to identify an entry uniquely
MAC beginMacAddr	1.3.6.1.4.1.34592.1.3.1.6.3.1.2	MacAddress	read-create	begin MAC address, this object must be set to effect this entry
MAC endMacAddr	1.3.6.1.4.1.34592.1.3.1.6.3.1.3	MacAddress	read-create	End MAC address of a MAC range entry. Set this value to zero will result that this entry only indicate a unique MAC.
INT macAttr	1.3.6.1.4.1.34592.1.3.1.6.3.1.4	INTEGER	read-create	This object is used to decide that the MAC(s) introduced in this entry should be classified into blackList or whiteList. When set to 'obsolete', this entry is not in use. This option is reserved for future use.
ROW onuAuthMacRowStatus	1.3.6.1.4.1.34592.1.3.1.6.3.1.5	RowStatus	read-create	This object is used to create or delete a MAC entry
nonAuthOnuListTable	1.3.6.1.4.1.34592.1.3.1.6.4		not-accessible	This table contain illegal ONU MAC list which try to register on OLT
nonAuthOnuListEntry	1.3.6.1.4.1.34592.1.3.1.6.4.1		not-accessible	Each entry in this table contain a nonAuth onu MAC info
U32 nonAuthOnuMacIndex	1.3.6.1.4.1.34592.1.3.1.6.4.1.1	Unsigned32	not-accessible	Administrativly assigned entry index
MAC nonAuthOnuMac	1.3.6.1.4.1.34592.1.3.1.6.4.1.2	MacAddress	read-only	The MAC address which tried to register
U32 nonAuthOnuTries	1.3.6.1.4.1.34592.1.3.1.6.4.1.3	Unsigned32	read-only	The times that the illegal ONU try to register
userManage	1.3.6.1.4.1.34592.1.3.1.7
userManageTable	1.3.6.1.4.1.34592.1.3.1.7.1		not-accessible	Description. Access user management table. The table defined the users who can access the system shell management interface, including local CLI and remote telnet access. The users defined in this table is independent with those defined in EMS.
userManageEntry	1.3.6.1.4.1.34592.1.3.1.7.1.1		not-accessible	Description. One entry contains one user attributes, up to 5 entries can be created in this table.
I32 userId	1.3.6.1.4.1.34592.1.3.1.7.1.1.1	Integer32	not-accessible	Administrativly assigned entry index
STR userName	1.3.6.1.4.1.34592.1.3.1.7.1.1.2	DisplayString	read-create	user name
OCT userPassword	1.3.6.1.4.1.34592.1.3.1.7.1.1.3	OCTET STRING	read-create	user password
U32 userPermission	1.3.6.1.4.1.34592.1.3.1.7.1.1.4	Unsigned32	read-only	Description. This object define the user priority and other permission attributes
U32 userAccessDeviceMap	1.3.6.1.4.1.34592.1.3.1.7.1.1.5	Unsigned32	read-create	This object is defined for future use. It is a bit map value which defines which devices in the system can be accessed by a user. Temporary definitions: ---------------------------------------------- \|sys level \| swithch module \| olt module\| onu \|............ ---------------------------------------------- high 2b 2b 5b 7b reserved low when the map bit set to 1, the user can access the corresponding device otherwise can not
U32 loginTimeout	1.3.6.1.4.1.34592.1.3.1.7.1.1.6	Unsigned32	read-only	Description. Time out time since one accessed user last operation, when this time elapse, the user will be kicked off
ROW userEntryRowStatus	1.3.6.1.4.1.34592.1.3.1.7.1.1.7	RowStatus	read-create	Use this object to create or delete a user info
upgrade	1.3.6.1.4.1.34592.1.3.1.8
STR ftpServerIp	1.3.6.1.4.1.34592.1.3.1.8.1	DisplayString	read-write	The host IP Address on which FTP server running and this host will be used as the server to do FTP operation
STR ftpServerUserName	1.3.6.1.4.1.34592.1.3.1.8.2	DisplayString	read-write	The user name used to access ftp server
STR ftpServerUserPasswd	1.3.6.1.4.1.34592.1.3.1.8.3	DisplayString	read-write	The user password which will be used to access ftp server
STR ftpOperFileName	1.3.6.1.4.1.34592.1.3.1.8.4	DisplayString	read-write	The file name which will be download to or upload from device. When the operation is download, the operation file should located on the host; When the operation is upload the file should located on the target device;
INT ftpOperTarget	1.3.6.1.4.1.34592.1.3.1.8.6	INTEGER	read-write	The operate target, which are device firmware or configuration file. When do upgrade or download,one of these file targets should be selected to operate. ctrlCardImage(1), ponCardImage(2), oltApp(3), oltPers(4), oltBoot(5), onuApp(6), onuPers(7), onuBoot(8), otherSpecifiedFile(9)
INT dwLoadFileCrcCheck	1.3.6.1.4.1.34592.1.3.1.8.7	INTEGER	read-write	This object is used to indicate the target device should or not to do crc check operation,if 'checkCrc' the operator should give the download file's crc calculate result on the 'dwLoadFileCrcValue' object. Crc check is now only useful when do download operation.
U32 dwLoadFileCrcValue	1.3.6.1.4.1.34592.1.3.1.8.8	Unsigned32	read-write	CRC value of the download file, this value will be used to compare with the CRC result calculated by the firmware running on device to check if error occurred during file transmission
OCT operDeviceMap	1.3.6.1.4.1.34592.1.3.1.8.9	OCTET STRING	read-write	This object defines the upgrade or download device objects,when do upgrade operation one or more device can be selected as operate objects. The data format defined as following: --------------------------------- \| slot \| olt \| onu \| --------------------------------- 1byte 1byte 8byte All these 10 bytes used as bit map for device selecting, when selected set the according bit to 1, else set to 0 The bit sequence in each used from low to high: For example: slot:0000 0101, select slot 1 and 3, dont select slot 2 and 4 and others(reserved) olt: 0000 0011 select olt(pon port) 1 and 2, dont select others(reserved) onu: byte[0] map to onuId 1~8; byte[1] map to onuId 9~16,..., byte[7] map to onuId 56~63 Bit map in byte[0]: b0~b7 map to onuId1~onuId8, etc.
INT upgradeStatus	1.3.6.1.4.1.34592.1.3.1.8.10	INTEGER	read-only	Upgrade process status
INT upgradeOperation	1.3.6.1.4.1.34592.1.3.1.8.11	INTEGER	read-write	This object defines an operation collection, which are used to do downlaod,upgrade or get file(upload) operations.
I32 ftpProgress	1.3.6.1.4.1.34592.1.3.1.8.12	Integer32	read-only	Description.
fdSysConformance	1.3.6.1.4.1.34592.1.3.1.13
fdSystemGroups	1.3.6.1.4.1.34592.1.3.1.13.1
sysBaseManageGroup	1.3.6.1.4.1.34592.1.3.1.13.1.1			A collection of objects providing fd system basic features management
chassisInfoGroup	1.3.6.1.4.1.34592.1.3.1.13.1.2			A collection of objects providing chassis information management
cardModuleGroup	1.3.6.1.4.1.34592.1.3.1.13.1.3			A collection of objects providing installed card module basic features management
onuAuthGroup	1.3.6.1.4.1.34592.1.3.1.13.1.4			A collection of objects providing ONU authentication MAC list management
userManageGroup	1.3.6.1.4.1.34592.1.3.1.13.1.5			A collection of objects providing system user management
systemUpgradeGroup	1.3.6.1.4.1.34592.1.3.1.13.1.6			A collection of objects providing system device upgrade management
fdSystemCompliances	1.3.6.1.4.1.34592.1.3.1.13.2
fdSystemCompliance	1.3.6.1.4.1.34592.1.3.1.13.2.1			The compliance statement

RFC description

Vendor-private MIB from Fortinet FortiDDoS systems that defines managed objects for DDoS mitigation appliance status, performance, and configuration.

Start monitoring C-Data FD-series OLT (system identity/firmware) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download FD-SYSTEM-MIB

What Is FD-SYSTEM-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description