F10-IF-EXTENSION-MIB

All MIBs › F10-IF-EXTENSION-MIB

Organization: Dell Inc

Last Updated: 2014--0-8-

Category: Network Interfaces, Technology: Switching/L2, Vendor: Dell/DNOS

Description: Dell Force10 MIB providing interface extensions beyond standard IF-MIB, including port-channel and VLAN interface specifics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is F10-IF-EXTENSION-MIB?

F10-IF-EXTENSION-MIB is a Dell Force10 proprietary MIB that augments the standard IETF IF-MIB with additional interface attributes specific to Dell Networking OS switches, such as extended details for port-channel (LAG) and VLAN logical interfaces. It generally exposes configuration and operational extensions layered on top of standard ifTable/ifXTable entries rather than introducing an entirely new data model. For monitoring purposes it is used to get a fuller software-level picture of interface configuration and status beyond the basic up/down state and counters that IF-MIB provides, helping confirm logical interfaces like port-channels and VLAN SVIs are configured and operating as expected. It is explicitly dependent on the standard IF-MIB (RFC 2863) which it extends, and likely also uses Dell's FORCE10-TC textual conventions. It is used in Dell Force10 switch/router deployments wherever port-channel bundling or VLAN interfaces need finer-grained SNMP visibility than IF-MIB alone provides. Engineers can download the F10-IF-EXTENSION-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in F10-IF-EXTENSION-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Dell Force10 (Dell EMC Networking) switches and routers

Monitoring Examples

No object or table names were captured for this MIB, so specific polling targets cannot be confirmed, but consistent with its role as an IF-MIB extension, an admin would expect to poll interface-extension objects indexed by ifIndex to see additional port-channel membership or VLAN-interface attributes not exposed by standard IF-MIB. A port-channel member interface not appearing in the expected extended table would indicate a LAG misconfiguration.

What Can Be Monitored

port-channel (LAG) interface details
VLAN interface attributes
extended interface configuration state

Imported Objects

From FORCE10-SMI

f10Mgmt

OBJECT-IDENTITY

From IF-MIB

ifIndex

OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter64
Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
TimeStamp
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
f10IfExtensionMib	1.3.6.1.4.1.6027.3.11			Dell Networking OS IF Extenstion MIB.
f10IfExtensionMibObject	1.3.6.1.4.1.6027.3.11.1
f10IfExtensionParams	1.3.6.1.4.1.6027.3.11.1.1
f10IfTable	1.3.6.1.4.1.6027.3.11.1.1.1		not-accessible	Dell Networking OS Extension ifTable contains generic interface parameters.
f10IfEntry	1.3.6.1.4.1.6027.3.11.1.1.1.1		not-accessible	A row defintion of Dell Networking OS Interface Extension parameters.
U32 f10IfIpMtu	1.3.6.1.4.1.6027.3.11.1.1.1.1.1	Unsigned32	read-write	The IP (Internet Protocol), Maximum Transmission Unit value.
INT f10IfDuplexMode	1.3.6.1.4.1.6027.3.11.1.1.1.1.2	INTEGER	read-write	Duplex mode of the interface. This will be read-write only for s60
STR f10IfQueueingStrategy	1.3.6.1.4.1.6027.3.11.1.1.1.1.3	DisplayString	read-only	Queueing strategy used for packets.
T/F f10IfRxFlowCtrl	1.3.6.1.4.1.6027.3.11.1.1.1.1.4	TruthValue	read-write	Flow control receive. This will be read-write only for s60
T/F f10IfTxFlowCtrl	1.3.6.1.4.1.6027.3.11.1.1.1.1.5	TruthValue	read-write	Flow Control transmit.This will be read-only only for s60
OCT f10IfDescr	1.3.6.1.4.1.6027.3.11.1.1.1.1.6	OCTET STRING	read-write	A textual string containing information about the interface. This will be read-write only for s60
INT f10IfAdminStatus	1.3.6.1.4.1.6027.3.11.1.1.1.1.7	INTEGER	read-write	A admin status of any interface. This will be read-write only for s60
U32 f10IfRateInterval	1.3.6.1.4.1.6027.3.11.1.1.1.1.8	Unsigned32	read-write	The rate info interval for the interface. This will be read-write only for s60
INT f10IfSpeed	1.3.6.1.4.1.6027.3.11.1.1.1.1.9	INTEGER	read-write	The interface's current bandwidth in bits per second. This will be read-write only for s60
I32 f10IfPortListBitPos	1.3.6.1.4.1.6027.3.11.1.1.1.1.10	Integer32	read-only	This is used for identifying the bit position in PortList Object for a given interface.
f10IfExtensionStats	1.3.6.1.4.1.6027.3.11.1.2
f10IfStaticsTable	1.3.6.1.4.1.6027.3.11.1.2.1		not-accessible	The statistcs information of the interfaces for performance monitoring.
f10IfStaticsEntry	1.3.6.1.4.1.6027.3.11.1.2.1.1		not-accessible	A row defintion of Dell Networking OS Extension interface statistics.
C64 f10IfInVlanPkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.1	Counter64	read-only	The total number of valid VLAN Tagged frames received.
C64 f10IfIn64BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.2	Counter64	read-only	The total number of frames (including bad frames) received that were 64 octets in length (excluding framing bits but in-cluding FCS octets).
C64 f10ifIn65To127BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.3	Counter64	read-only	The total number of frames (including bad frames) received that were between 65 and 127 octets in length inclusive (ex-cluding framing bits but including FCS octets).
C64 f10IfIn128To255BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.4	Counter64	read-only	The total number of frames (including bad frames) received that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).
C64 f10IfIn256To511BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.5	Counter64	read-only	The total number of frames (including bad frames) received that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).
C64 f10IfIn512To1023BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.6	Counter64	read-only	The total number of frames (including bad frames) received that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).
C64 f10IfInOver1023BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.7	Counter64	read-only	The total number of frames received that were longer than 1023 (1025 Bytes in case of VLAN Tag) octets (excluding framing bits, but including FCS octets) and were otherwise well formed. This counter is not incremented for too long frames.
C64 f10IfInThrottles	1.3.6.1.4.1.6027.3.11.1.2.1.1.8	Counter64	read-only	This counter is incremented when a valid frame with a length or type field value equal to 0x8808 (Control Frame) is re-ceived.
C64 f10IfInRunts	1.3.6.1.4.1.6027.3.11.1.2.1.1.9	Counter64	read-only	The total number of frames received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.
C64 f10IfInGiants	1.3.6.1.4.1.6027.3.11.1.2.1.1.10	Counter64	read-only	The total number of frames received that were longer than 1518 (1522 Bytes in case of VLAN Tag) octets (excluding framing bits, but including FCS octets) and were otherwise well formed. This counter is not incremented for too long frames.
C64 f10IfInCRC	1.3.6.1.4.1.6027.3.11.1.2.1.1.11	Counter64	read-only	The total number of frames received that had a length (ex-cluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had a bad CRC.
C64 f10IfInOverruns	1.3.6.1.4.1.6027.3.11.1.2.1.1.12	Counter64	read-only	The total number of frames dropped because of buffer issue.
C64 f10IfOutVlanPkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.13	Counter64	read-only	The Number of Good VLAN Tagged Frames sent successfully.
C64 f10IfOutUnderruns	1.3.6.1.4.1.6027.3.11.1.2.1.1.14	Counter64	read-only	The total number of frames dropped because of buffer underrun.
C64 f10IfOutUnicasts	1.3.6.1.4.1.6027.3.11.1.2.1.1.15	Counter64	read-only	The Number of Good Unicast Frames sent successfully.
C64 f10IfOutCollisions	1.3.6.1.4.1.6027.3.11.1.2.1.1.16	Counter64	read-only	A count of the frames that due to excessive or late collisions are not transmitted successfully.
C64 f10IfOutWredDrops	1.3.6.1.4.1.6027.3.11.1.2.1.1.17	Counter64	read-only	A count of the frames that are dropped using WRED policy because of to excessive traffic.
C64 f10IfOut64BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.18	Counter64	read-only	The Number of Good Frames sent successfully whose size was 64 Bytes.
C64 f10IfOut65To127BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.19	Counter64	read-only	The Number of Good Frames sent successfully whose size was in the range of 65 to 127 Bytes.
C64 f10IfOut128To255BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.20	Counter64	read-only	The Number of Good Frames sent successfully whose size was in the range of 128 to 255 Bytes.
C64 f10IfOut256To511BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.21	Counter64	read-only	The Number of Good Frames sent successfully whose size was in the range of 256 to 511 Bytes.
C64 f10IfOut512To1023BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.22	Counter64	read-only	The Number of Good Frames sent successfully whose size was in the range of 512 to 1023 Bytes.
C64 f10IfOutOver1023BytePkts	1.3.6.1.4.1.6027.3.11.1.2.1.1.23	Counter64	read-only	The Number of Good Frames sent successfully whose size was greater than 1023 Bytes.
C64 f10IfOutThrottles	1.3.6.1.4.1.6027.3.11.1.2.1.1.24	Counter64	read-only	This counter is incremented when a valid frame with a length or type field value equal to 0x8808 (Control Frame) is sent.
TIM f10IfLastDiscontinuityTime	1.3.6.1.4.1.6027.3.11.1.2.1.1.25	TimeStamp	read-only	The value of sysUpTime on the most recent occasion at which this interface's counters suffered a discontinuity via a reset. If no such discontinuities have occurred since the last reinitialization of the local management subsystem, then this object contains a zero value.
I32 f10IfInCentRate	1.3.6.1.4.1.6027.3.11.1.2.1.1.26	Integer32	read-only	This is the ingress rate in percentage. This is an integer value which can go from 0 to 100.
I32 f10IfOutCentRate	1.3.6.1.4.1.6027.3.11.1.2.1.1.27	Integer32	read-only	This is the egress rate in percentage. This is an integer value which can go from 0 to 100.
f10IfExtensionMibConformance	1.3.6.1.4.1.6027.3.11.2
f10IfExtensionMibCompliances	1.3.6.1.4.1.6027.3.11.2.1
f10IfExtensionMibCompliance	1.3.6.1.4.1.6027.3.11.2.1.1			The compliance statement for Dell Networking OS IF Extension MIB.
f10IfExtensionMibGroups	1.3.6.1.4.1.6027.3.11.2.2
f10IfParamsGroup	1.3.6.1.4.1.6027.3.11.2.2.1			A collection of objects providing the Dell Networking OS IF Extenstion parameters.
f10IfStatsGroup	1.3.6.1.4.1.6027.3.11.2.2.2			A collection of objects providing the interface statistics.

RFC description

Force10 interface extension MIB for Dell Force10 switches. Extends standard interface MIB with additional statistics, port modes, and forwarding parameters.

Start monitoring Dell Force10 switch/router (extended interface/port-channel/VLAN attributes) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download F10-IF-EXTENSION-MIB

What Is F10-IF-EXTENSION-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description